View ENH104V2-380_251524.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
White Electronic Designs Display Systems Division
GENERAL DESCRIPTION
WEDC provides optically enhanced solutions to the standard Optrex AA104VB05 color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module. The first enhancement is an index matching (IM) film lamination to the front surface of the display polarizer. The IM film is a contrast enhancement benefit and is available in two surface treatments - IM/Clear and IM/110 (a 10% diffusion).The second enhancement is the incorporation of reflective polarizer (RP) to improve brightness by up to 40%. The third enhancement is the incorporation of an enhanced light guide (ELG) to improve brightness by up to 35%. The resultant brightness level are shown in the Specifications below. This module is composed of a color LCD panel, driver ICs, control circuit, and a backlight unit. By applying 6 bit digital data 640 x 480, 260K-color images are displayed on the 10.4" diagonal screen. Input power voltage is single 3.3V/5V for LCD driving. Both 3.3V-CMOS and 5.0V-CMOS level voltage are acceptable for logic input voltage. Inverter for backlight is not included in this module. General specifications are summarized in the following table:
ITEM Display Area (mm)
ENH104V2-380/450/600
ENH104V2-380/450/600 Color TFT-LCD Module Features
SPECIFICATIONS
SPECIFICATION 211.2 (H) x 158.4 (V) (10.39-inch diagonal) 640 x 3 (H) x 480 (V) 0.33 (H) x 0.33 (V) RGB vertical stripe normally white 260K Optical compensation film 12 o'clock
Number of Dots Pixel Pitch (mm) Color Pixel Arrangement Display Mode Number of Color Wide Viewing Angle Technology Optimum Viewing Angle (Contrast ratio) Brightness (cd/m2) ENH104V2-380 (IM only) ENH104V2-450 (IM, RP) ENH104V2-600 (IM, RP, ELG) Module Size (mm) Module Mass (g) Backlight Unit Surface Treatment
380 450 600 243.0 (W) x 181.6 (H) x 12.2 (D) 530 CCFL, 2-tubes, replacements IM/Clear (glossy) or IM/110 and hardcoat 3H
Characteristic value without any note is typical value.
The LCD product described in this specification is designed and manufactured for the standard use in office automation equipment, instrumentation, communication equipment, automation, point of sale, etc. WEDC assumes no responsability for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specifications sheets. WEDC does assume the responsability for the warranty of the enhanced product.
ABSOLUTE MAXIMUM RATINGS
ITEM Power Supply Voltage for LCD Logic Input Voltage Lamp Voltage Lamp Current Lamp Frequency Operating temperature (1) Storage Temperature (1) SYMBOL VCC VI VL IL FL TOP TSTG MIN -0.3 0 0 0 0 -20 MAX 6.5 6.5 2000 10.0 80 50 60 Unit V V VRMS mArms kHz C C
Notes: 1. tOP, tSTG < 40C: 90%RH max. without condensation 2. tOP, tSTG < 40C: Absolute humidity shall be less than the value of 90%RH at 40C without condensation.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 1 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
ELECTRICAL CHARACTERISTICS
ENH104V2-380/450/600
TFT-LCD PANEL DRIVING, tA=25C
Power Supply Voltage for LCD Power Supply Current for LCD ITEM 3.3 V powered 5.0 V powered SYMBOL VCC VCC ICC ICC VRP VIH VIL MIN 3.0 4.75 2.0 0 TYP 3.3 5.0 220 150 MAX 3.6 5.25 380 280 100 5.25 0.8 UNIT V V mA mA mVp-p V V REMARK (A), (D) (A), (D) VCC = 3.3V (B) VCC = 5.0V (B) VCC = -3.3V/5.0V (B)
3.3 V powered 5.0 V powered Permissive Input Ripple Voltage Logic Input High Voltage Low
BACKLIGHT tA=25C
ITEM SYMBOL
Lamp Voltage Lamp Current Lamp frequency Starting Lamp Voltage Lamp Life Time
tA=25C tA=0C IL=3.0mArms IL=6.0mArms IL=7.0mArms
VL IL FL VS LT
MIN 3.0 40 810 1000 50000 40000 30000
TYP 580 6.0 50000 50000 40000
MAX 7.0 80 -
UNIT
REMARK
Vrms mArms kHz Vrms Vrms hour hour hour
IL=6.0mArms (1) (2)
(3), (4)
CTL CTH
A
LCD Module
CTL CTH
A
Inverter
Power Supply
Notes: 1. Lamp current measurement method (The current meter is inserted in low voltage line.) 2. Lamp frequency of inverter may produce interference with horizontal synchronous frequency,and this may cause horizontal beat on the display. Therefore, please adjust lamp frequency, and keep inverter as far from module as possible or use electronic shielding between inverter and module to avoid the interference. 3. Lamp life time is defined as the time either when the brightness becomes 50% of the initial value, or when the starting lamp voltage does not meet the value specified in this table. 4. The life time of the backlight depends on the ambient temperature. The life time will decrease under low/high temperature.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 2 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
Notes: 1. Power and signals sequence: t1 < 10ms 400ms < t5 0 < t2 < 50ms 200ms < t6 0 < t3 < 50ms 0 < t7 0 < t4 < 50ms
ENH104V2-380/450/600
VCC 0.9VCC Data 0.1VCC 0.1VCC 0.1VCC 0.9VCC
t1
t2 Backlight
t3
t4
t5
t6
t7
Data: RGB DATA, DCLK, HD, VD, DENA
VCC-dip conditions A. 3.3V powered 1. When 2.4 V < VCC < 3.0V, td <10ms . 2. When VCC < 2.4V VCC-dip conditions should also follow the power and signals sequence.
VCC
td
2.4 V
3.0 V
B. .
5.0V powered 1. When 3.6 V < VCC < 4.5V, td <10ms 2. When VCC < 3.6V VCC-dip conditions should also follow the power and signals sequence.
VCC
td
B. Typical current conditions: 64-gray-bar-pattern 480 line mode VCC = +3.3/5.0 V, fH=31.6kHz, fv=60Hz, fCK=25MHz
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 3 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
3.6 V
4.5 V
White Electronic Designs Display Systems Division
INTERPACE PIN CONNECTIONS
ENH104V2-380/450/600
CN1 (Interface Signal) Used Connector: DF9B-31P-1V (Hirose)/Corresponding connector: DF9B-31S-1V(Hirose)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Note: 1. 2. The shielding case is connected with GND. See; Timing Chart (p. 7)
Symbol GND DCK HD VD GND R0 R1 R2 R3 R4 R5 GND G0 G1 G2 G3 G4 G5 GND B0 B1 B2 B3 B4 B5 GND DENA VCC VCC TEST SC
Function Clock signal for sampling each data signal Horizontal synchronous signal Vertical synchronous signal RED data signal (LSB) RED data signal RED data signal RED data signal RED data signal RED data signal (MSB) GREEN data signal (LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal (MSB) BLUE data signal (LSB) BLUE data signal BLUE data signal BLUE data signal BLUE data signal BLUE data signal (MSB) Data enable signal(to settle the viewing area) +3.3/5.0V power supply +3.3/5.0V power supply This pin should be open. Test signal output for only internal test use. Scan direction Control. (GND or Open: Normal, High: Reverse)
CN2, CN3 (Backlight) Backlight-side connector: BHR-02(8.0)VS-1N(JST) Inverter-Side Connector: SM02(8.0)B-BHS(JST)
Note: VBLH-VBLL-VL
Pin No. 1 3
Symbol CTH CTL
Function VBLH High Voltage VBLL Low Voltage
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 4 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
INTERFACE TIMING
TIMING SPECIFICATIONS
DCK (1)(4) ITEM Frequency Period High Width Low Width Set up time Hold time Horizontal Active Time Horizontal Front Porch Horizontal Back Porch Vertical Active Time Vertical Front Porch Vertical Back Porch Frequency Period Low Width Frequency Period Low Width SYMBOL fCK tCK tWCL tWCH tDS tDH tHA tHFP tHBP tVA tVFP tVBP fH tH tWHL fV tV tWVL MIN 34.5 12 12 5 5 640 10 2 480 1 2 27 26.3 5 55 14.3 3
ENH104V2-380/450/600
DATA (1) (R,G,B, DENA HD, VD) DENA (3)
HD (2)(4)
VD (2)
TYP 25 40 640 16 144 480 12 33 31.6 31.6 96 60 16.7 -
MAX 29 640 480 38 37.0 70 18.2 -
UNIT MHz ns ns ns ns ns tCK tCK tCK tH tH tH kHz s tCK Hz ms tH
Notes: 1. DATA is latched at fall edge of DCK in this specification. 2. Polarities of HD and VD are negative in the specification. 3. DENA (Data Enable) should always be positive polarity as shown in the timing specification. 4. DCK should appear during all invalid period, and HD should appear during invalid period of frame cycle.
PIXEL TIMING CHART
tCK t WCH t WCL 2.0V 0.8V
DCK
t DS
t DH 2.0V 0.8V
D ATA ( R G B ) , DENA, HD, VD
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 5 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
HORIZONTAL TIMING CHART
DCK
ENH104V2-380/450/600
First Data
DATA (RGB)
Invalid Data
1
2
3
639
640
Invalid Data Last Data
t HFP
t HBP
t HA
DENA
t H =1/f H t WHL
HD
VERTICAL TIMING CHART
HD
LINE DATA
Invalid Data
1
2
3
479
480
Invalid Data
t VFP
t VBP
t VA
DENA
t V=1/f V t WVL
VD
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 6 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
R DATA R3 R2 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 1 0 0 0 G DATA G3 G2 0 0 1 0 1 0 1 1 0 0 0 0 0 1 0 1 0 1 1 0 0 0
ENH104V2-380/450/600
COLOR DATA ASSIGNMENT
COLOR INPUT DATA BLACK RED (63) GREEN (63) BLUE (63) CYAN MAGENTA YELLOW WHITE RED (0) RED (1) RED (2) R5 MSB 0 1 0 0 0 1 1 1 0 0 0 R4 0 1 0 0 0 1 1 1 0 0 0 R1 0 1 0 0 0 1 1 1 0 0 1 R0 G5 LSB MSB 0 0 1 0 0 1 0 0 0 1 1 0 1 1 1 1 0 0 1 0 0 0 G4 0 0 1 0 1 0 1 1 0 0 0 G1 0 0 1 0 1 0 1 1 0 0 0 G0 LSB 0 0 1 0 1 0 1 1 0 0 0 B5 MSB 0 0 0 1 1 1 0 1 0 0 0 B4 0 0 0 1 1 1 0 1 0 0 0 B DATA B3 B2 0 0 0 1 1 1 0 1 0 0 0 0 0 0 1 1 1 0 1 0 0 0 B1 0 0 0 1 1 1 0 1 0 0 0 B0 LSB 0 0 0 1 1 1 0 1 0 0 0
BASIC COLOR
RED RED (62) RED (63) GREEN () GREEN () GREEN () GREEN GREEN () GREEN () BLUE () BLUE () BLUE () BLUE BLUE () BLUE () 1 1 1 1 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 0 0 0 0 1 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0 1 1 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 0 0 0 1 1 0 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Notes: 1. Definition of gray scale Color (n) ...n indicates gray scale level. Higher n means brighter lever. 2. Data 1:High, 0:Low
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 7 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
BLOCK DIAGRAM
ENH104V2-380/450/600
Timing signal Display data
Timing Converter
G1
Driver (gate)
I/F Connector
G2
TFT-LCD
G480 S1919 S1920
Power
S1 Power Supply Circuit BACKLIGHT CN2, 3 1 3 CCFL
Driver(source)
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 8 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
S2
White Electronic Designs Display Systems Division
MECHANICAL SPECIFICATIONS
243 0.5 8 5 0.3 2.5 0.2 7.5 4.2 12.4 14.5 235 0.3 215.4 (Bezel Opening) 211.2 (Display Area)
ENH104V2-380/450/600
BHR-02(8.0)VS-1N 60 10
5
17 0.3
4
2 - O 3.5
90.8
2-R 1.75 2.5 0.2 2.9 5 0.3 161.8 (Bezel Opening) 158.4 (Display Area)
10 Display Center DF9B-31P-1V 2.9 10 90 60 10 124.3 BHR-02(8.0)VS-1N
181.6 0.5
8.6 60
55
166.6 0.3
12.2 0.5
5
4
REAR VIEW
Note: Tolerance is 0.5mm unless noted.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 9 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
132.6 03
White Electronic Designs Display Systems Division
SCANNING DIRECTION
SC : High
ENH104V2-380/450/600
D(1,1)
D(640,1) CN2
D(1,480)
D(640,480)
CN3
SC : GND or Open
D(1,1) CN3
D(640,1)
CN2 D(1,480) D(640,480)
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 10 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
OPTICAL CHARACTERISTICS
ENH104V2-380/450/600
tA=25C, VCC=3.3/5.0V, Input Signals: TYP Values Shown in Section 5
Parameter Contrast Ratio Luminance ENH104V2-380 (IM only) ENH104V2-450 (IM, RP) ENH104V2-600 (IM, RP, ELG) Response Time Viewing Angle Horizontal Vertical Red Green Color Coordinates Blue White Symbol CR Lw Condition = =0 = =0 tr tf Rx Ry Gx Gy Bx By Wx Wy = =0 = =0 CR > 10 0.54 0.30 0.30 0.49 0.14 0.15 0.29 0.31 Min 150 Typ 300 380 450 600 15 35 -60~60 -45~55 0.57 0.33 0.33 0.52 0.17 0.18 0.32 0.34 Max Unit cd/m2 0.60 0.36 0.36 0.55 0.20 0.21 0.35 0.37 ms ms Remarks 1, 3 2, 3 3, 4 3, 4 3 3
= =0
-
3
Notes: These items are measured using BM-5A (TOPCON) or LCD-7000 (Otsuka Electronic) under the dark room condition (no ambient light). Condition: IL=6.0mArms, FL-55kHz 1. Definition of Luminance CR=ON (White) Luminance/OFF (Black) Luminance: average of 5 points. 2. Definition of luminance Lw=ON (White) Luminance: average of 5 points.
(1,1) 120 240 360
160 1
320
480 2 5
3
4 (640,480)
Measurement Point
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 11 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
3. Definition of Viewing Angle (, )
ENH104V2-380/450/600
Upper (+)
Left (-)
Right (+)
LCD panel
Lower (-)
4.
Definition of Response Time
Whi te 90% 90%
L uminance
10% tr
Black
10%
tf
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 12 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
ENH104V2-380/450/600
RELIABILITY TEST CONDITIONS TEMPERATURE & HUMIDITY
TEST ITEMS High Temperature High Humidity Operation High Temperature Storage Low Temperature Storage Thermal Shock (non-operation) CONDITIONS 40C, 90%RH, 240 h 60C, 96 h -20C, 96 h Between -20C (1h) and 60C (1h), 5 cycles
SHOCK & VIBRATION
ITEM Shock (non-operation) CONDITIONS Shock level: 1470m/s2 (150G) Waveform: half sinusoidal wave, 2ms Number of shocks: one shock input in each direction of three mutually perpendicular axis for a total of six shock inputs Vibration level: 9.8m/s2 (1.0G) Waveform: sinusoidal Frequency range: 5 to 500Hz Frequency sweep rate: 0.5 octave /min Duration: one sweep from 5 to 500 to 5Hz in each of three mutually perpendicular axis (total 3 hours)
Vibration (non-operation)
JUDGEMANT STANDARD
The judgement of the above test should be made as follow: Pass: Normal display image with no obvious non-uniformity and no line defect. Partial transformation of the module parts should be ignoreed. Fail: No display image, obvious non-uniformity, or line defects.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 13 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
ASSEMBLY PRECAUTIONS
1. Please use the mounting hole on the module in installing and do not bending or wrenching LCD in assembling. And please do not drop, bend or twist LCD module in handling. 2. Please design display housing in accordance with the following guide lines. (a) Housing case must be designed carefully so as not to put stresses on LCD all sides and not to wrench module. The stresses may cause non-uniformity even if there is no nonuniformity statically. (b) Keep sufficient clearance between LCD module back surface and housing when the LCD module is mounted. Approximately 1.0mm of the clearance in the design is recommended taking into account the tolerance of LCD module thickness and mounting structure height on the housing. (c) When some parts, such as, FPC cable and ferrite plate, are installed underneath the LCD module, still sufficient clearance is required, such as 0.5mm. This clearance is, especially, to be reconsidered when the additional parts are implemented for EMI countermeasure. (d) Design the inverter location and connector position carefully so as not to give stress to lamp cable, or not to interface the LCD module by the lamp cable. (e) Keep sufficient clearance between LCD module and the others parts, such as inverter and speaker so as not to interface the LCD module. Approximately 1.0mm of the clearance in the design is recommended. 3. Please do not push or scratch LCD panel surface with anything hard. And do not soil LCD panel surface by touching with bare hands. (Polarizer film, surface of LCD panel is easy to be flawed.) 4. Please do not press any parts on the rear side such as source TCP, gate TCP, control circuit board and FPCs during handling LCD module. If pressing rear part is unavoidable, handle the LCD module with care not to damage them. 5. Please wipe off LCD panel surface with absorbent cotton or soft cloth in case of it being soiled.
ENH104V2-380/450/600
HANDLING PRECAUTIONS FOR TFT-LCD MODULE
6. Please wipe off drops of adhesives like saliva and water on LCD panel surface immediately. They might damage to cause panel surface variation and color change. 7. Please do not take a LCD module to pieces and reconstruct it. Resolving and reconstructing modules may cause them not to work well. 8. Please do not touch metal frames with bare hands and soiled gloves. A color change of the metal frames can happen during a long preservation of soiled LCD modules. 9. Please pay attention to handling lead wire of backlight so that it is not tugged in connecting with inverter. 10. Please connect the metal frame of LCD module to GND in order to minimize the effect of external noise and EMI. 11. Please connect the metal frame of LCD module to GND in order to minimize the effect of external noise and EMI.
OPERATING PRECAUTIONS
1. Please be sure to turn off the power supply before connecting and disconnecting signal input cable. 2. Please do not change variable resistance settings in LCD module. They are adjusted to the most suitable value. If they are changed, it might happen LCD does not satisfy the characteristics specification. 3. LCD backlight takes longer time to become stable of radiation characteristics in low temperature than in room temperature. 4. A condensation might happen on the surface and inside of LCD module in case of sudden change of ambient temperature. 5. Please pay attention not to display the same pattern for very long time. Image might stick on LCD. Even if image sticking happens, it may disappear as the operation time proceeds. 6. Please obey the same safe instructions as ones being prepared for ordinary electronic products.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 14 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0
White Electronic Designs Display Systems Division
PRECAUTIONS WITH ELECTROSTATICS
1. This LCD module use CMOS-IC on circuit board and TFT-LCD panel, and so it is easy to be affected by electrostatics. Please be careful with electrostatics by the way of your body connecting to the ground and so on. 2. Please remove protection film very slowly from the surface of LCD module to prevent from electrostatics occurrence.
ENH104V2-380/450/600
OTHERS
1. A strong incident light into LCD panel might cause display characteristics changing inferior because of polarizer film, color filter, and other materials becoming inferior. Please do not expose LCD module direct sunlight and strong UV rays. 2. Please pay attention to a panel side of LCD module not to contact with other materials in preserving it alone. 3. For the packaging box, please pay attention to the followings; (a) Packaging box and inner case for LCD are designed to protect the LCDs from the damage or scratching during transportation. Please do not open except picking LCDs up from the box. (b) Please do not pile them up more than 5 boxes. (They are not designed so.) And please do not turn over. (c) Please handle packaging box with care not to give them sudden shock and vibrations. And also please do not throw them up. (d) Packaging box and inner case for LCDs are made of cardboard. So please pay attention not to get them wet. (Such like keeping them in high humidity or wet place can occur getting them wet.)
STORAGE PRECAUTIONS
1. Please do not leave the LCDs in the environment of high humidity and high temperature such as 60C90%RH. 2. Please do not leave the LCDs in the environment of low temperature; below -20C.
SAFETY PRECAUTIONS
1. When you waste damaged or unnecessary LCDs, it is recommended to crush LCDs into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned. 2. If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash off thoroughly with soap and water. 3. Be sure to turn off the power supply when inserting or disconnecting the cable. 4. Inverter should be designed carefully so as not to keep working in case of detecting over current or open circuit on the lamp.
White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 15 Display Systems Division * Hillsboro, OR * (503) 690-2460 * www.wedc.com Rev. 0

▲Up To Search▲

Price & Availability of ENH104V2-380

	To Download ENH104V2-380 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .