|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
LCD MODULE www..com ET12864CV3 2006-04-06 PRODUCT SPECIFICATION FOR LCM MODULE MODULE NO. : ET12864CV3 REVERSION : A TYPE : COB Customer Approval: PREPARED BY DATE CHECKED BY DATE APPROVED BY DATE EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com Fax: 86-755-83421997 Http//www.eastet.com 1 LCD MODULE www..com ET12864CV3 2006-04-06 DOCUMENT REVISION HISTORY VERSION A DATE 2006-04-06 DESCRIPTION First issue CHANGED BY Ken EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com Fax: 86-755-83421997 Http//www.eastet.com 2 LCD MODULE www..com ET12864CV3 2006-04-06 CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. PHYSICAL DATA EXTERNAL DIMENSIONS ABSOLUTE MAXIMUM RATINGS OPERATING PRINCIPLES & METHODS ELECTRICAL CHARACTERISTICS ELECTRO-OPTICAL CHARACTERISTICS CAUTIONS FOR USING LCD MODULES USING LCD MODULES 1. PHYSICAL DATA Dots Format : 128*64Dots. 3 Fax: 86-755-83421997 Http//www.eastet.com EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com LCD MODULE www..com ET12864CV3 2006-04-06 LCD mode Viewing direction Driving condition Power supply voltage Backlight Type Operating temperature Storage temperature Module size (LxWxH) Viewing area (LxW) Dot size (WxH) Dot pitch (WxH) : STN, Yellow Green : 6 o'clock : 1/64 Duty , 1/9 Bias . : +5V : Yellow Green LED Backlight, : 0~50C : -10~60C : Refer to the outline drawing . : Refer to the outline drawing . : Refer to the outline drawing . : Refer to the outline drawing . 2. EXTERNAL DIMENSIONS Figure 1. External Dimensions 3. ABSOLUTE MAXIMUM RATINGS ( Ta = 25C ) Table 1. Absolute Maximum Ratings EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com Fax: 86-755-83421997 Http//www.eastet.com 4 LCD MODULE www..com ET12864CV3 2006-04-06 Parameter Supply voltage for logic Supply current Supply voltage for LED Supply current for LED Operating temperature Storage temperature *Note: Based on Vss=0V. Symbol Vdd Idd Vled Iled Top Tst Min -0.3 - Max 7.0 10 5.0 100 Unit V mA V mA C C 0 -10 50 60 4. OPERATING PRINCIPLES & METHODS Table 2. Interface Pin Connections Pin Symbol Level Description No. 1 FG Power supply Ground of frame 2 3 4 5 6 7 8 9. 10~1 7 18 19 20 VSS VDD Vo /WR /RD /CE C/D /RST DB0~DB7 FS LEDA LEDK 5V 0V Power supply Power supply Power supply H/L H/L H/L H/L H/L H/L Ground Power supply +. Operation voltage of LCD Write Read Chip select signal for IC H: DB<0:7> Display RAM Data, L: DB<0:7> Instruction Data Reset signal Data Bus Font select Side light anode Side light cathode Figure 2. Block Diagram EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com Fax: 86-755-83421997 Http//www.eastet.com 5 LCD MODULE www..com ET12864CV3 2006-04-06 Instruction table EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com Fax: 86-755-83421997 Http//www.eastet.com 6 LCD MODULE www..com ET12864CV3 2006-04-06 See the "T6963C" data sheet of TOSHIBA to get more detail. 5. ELECTRICAL CHARACTERISTICS (Based on Ta = -20 to 70 deg. C, Vss = 0 V) DC Characteristics Table 3. DC Characteristics Item Operating voltage Supply current VOP Supply backlight voltage Input backlight current Output voltage Input voltage Symbol VDD IDD VDD-VO Vled Iled VOUT VIL VIH 0 0.7V DD Min 4.5 19 4.5 20.0 5.0 -10 Type 5.0 Max 5.5 10 21 5.5 100 0.3VDD V mA V V V Unit V mA Applicable terminal VDD VDD,VO LEDA,LEDK LEDA,LEDK VOUT RS,R/W,CS1,CS 2,E,DB0~DB7 Test condition -During display 25C Turn on LED Turn on LED VDD=5V - 6. ELECTRO-OPTICAL CHARACTERISTICS (VDD=5.0V, Ta = 25 C) Table 5. Electro-Optical Characteristics Item Contrast ratio Symbol Cr Condition --Min 2 35 Viewing angle range Cr 2 35 50 33 Type 3 --------Max ----------Unit --deg deg deg deg Remarks -- = 90 = 270 = 0 = 180 Note 1 2 2 2 2 7 Fax: 86-755-83421997 Http//www.eastet.com EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com LCD MODULE www..com ET12864CV3 2006-04-06 Figure 6. Definition of contrast ratio `Cr'. & viewing angle range `'. Note1: Definition of contrast ratio Cr . Note2: Definition of viewing angle range `. 7. PRECAUTIONS FOR USING LCD MODULES Handing Precautions (1) The display panel is made of glass. Do not subject it to a mechanical shock by dropping it or impact. (2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the substance contacts your skin or clothes, wash it off using soap and water. (3) Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. (4) The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. (5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If it is heavily contaminated, moisten cloth with one of the following solvents : - Isopropyl alcohol - Ethyl alcohol (6) Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the following. - Water - Ketone - Aromatic solvents (7) Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water droplets, moisture condensation or a current flow in a high-humidity environment. (8) Install the LCD Module by using the mounting holes. When mounting the LCD module make sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the backlight cable. (9) Do not attempt to disassemble or process the LCD module. (10) NC terminal should be open. Do not connect anything. (11) If the logic circuit power is off, do not apply the input signals. (12) To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. - Be sure to ground the body when handling the LCD modules. - Tools required for assembling, such as soldering irons, must be properly grounded. - To reduce the amount of static electricity generated, do not conduct assembling and other work under dry conditions. EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com Fax: 86-755-83421997 Http//www.eastet.com 8 LCD MODULE www..com ET12864CV3 2006-04-06 - The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated. Storage Precautions When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. Keep the modules in bags (avoid high temperature / high humidity and low temperatures below 0C). Whenever possible, the LCD modules should be stored in the same conditions in which they were shipped from our company. Others Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low temperature. If the LCD modules have been operating for a long time showing the same display patterns, the display patterns may remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating status can be regained by suspending use for some time. It should be noted that this phenomenon does not adversely affect performance reliability. To minimize the performance degradation of the LCD modules resulting from destruction caused by static electricity etc., exercise care to avoid holding the following sections when handling the modules. - Exposed area of the printed circuit board. - Terminal electrode sections. 8. USING LCD MODULES Liquid Crystal Display Modules LCD is composed of glass and polarizer. Pay attention to the following items when handling. (1) Please keep the temperature within specified range for use and storage. Polarization degradation, bubble generation or polarizer peel-off may occur with high temperature and high humidity. (2) Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass, tweezers, etc.). (3) N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors made of organic substances which will be damaged by chemicals such as acetone, toluene, ethanol and isopropylalcohol. (4) When the display surface becomes dusty, wipe gently with absorbent cotton or other soft material like chamois soaked in petroleum benzin. Do not scrub hard to avoid damaging the display surface. (5) Wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or color fading. (6) Avoid contacting oil and fats. (7) Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizers. After products are tested at low temperature they must be warmed up in a container before coming is contacting with room temperature air. (8) Do not put or attach anything on the display area to avoid leaving marks on. (9) Do not touch the display with bare hands. This will stain the display area and degradate insulation between terminals (some cosmetics are determinated to the polarizers). (10) As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Installing LCD Modules The hole in the printed circuit board is used to fix LCM as shown in the picture below. Attend to the following items when installing the LCM. (1) Cover the surface with a transparent protective plate to protect the polarizer and LC cell. EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com Fax: 86-755-83421997 Http//www.eastet.com 9 LCD MODULE www..com ET12864CV3 2006-04-06 (2) When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting plate should have enough height to avoid causing stress to the module surface, refer to the individual specifications for measurements. The measurement tolerance should be 0.1mm. Precaution for Handing LCD Modules Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it. (1) Do not alter, modify or change the shape of the tab on the metal frame. (2) Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be attached. (3) Do not damage or modify the pattern writing on the printed circuit board. (4) Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector. (5) Except for soldering the interface, do not make any alterations or modifications with a soldering iron. (6) Do not drop, bend or twist LCM. (7) In order to avoid the cracking of the FPC, you should to pay attention to the area of FPC (R50mm) where the FPC was bent .the edge of coverlay ; the area of surface of Ni-Au plating, the area of soldering land, the area of through hole. Electro-Static Discharge Control Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as for an ordinary CMOS IC. (1) Make certain that you are grounded when handing LCM. (2) Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body have the same electric potential. (3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak. (4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor. (5) As far as possible make the electric potential of your work clothes and that of the work bench the ground potential. (6) To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative humidity of 50%-60% is recommended. Precaution for soldering to the LCM (1) Observe the following when soldering lead wire, connector cable and etc. to the LCM. - Soldering iron temperature : 260C 10C. - Soldering time : 3-4 sec. - Solder : eutectic solder. If soldering flux is used, be sure to remove any remaining flux after finishing to soldering operation. (This does not apply in the case of a non-halogen type of flux.) It is recommended that you protect the LCD surface with a cover during soldering to prevent any damage dur to flux spatters. (2) When soldering the electroluminescent panel and PC board, the panel and board should not be detached more than three times. This maximum number is determined by the temperature and time conditions mentioned above, though there may be some variance depending on the temperature of the soldering iron. EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com Fax: 86-755-83421997 Http//www.eastet.com 10 LCD MODULE www..com ET12864CV3 2006-04-06 (3) When remove the electoluminescent panel from the PC board, be sure the solder has completely melted, the soldered pad on the PC board could be damaged. (4)Soldering iron is not allowed to touch the surface of FPC's cover film directly. Precautions for Operation (1) Viewing angle varies with the change of liquid crystal driving voltage (VO). Adjust VO to show the best contrast. (2) Driving the LCD in the voltage above the limit shortens its life. (3) Response time is greatly delayed at temperature below the operating temperature range. However, this does not mean the LCD will be out of the order. It will recover when it returns to the specified temperature range. (4) If the display area is pushed hard during operation, the display will become abnormal. However, it will return to normal if it is turned off and then back on. (5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. Therefore, it must be used under the relative condition of 40C , 50% RH. (6) When turning the power on, input each signal after the positive/negative voltage becomes stable. Storage When storing LCDs as spares for some years, the following precaution are necessary. (1) Store them in a sealed polyethylene bag. If properly sealed, there is no need for dessicant. (2) Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the temperature between 0C and 35C. (3) The polarizer surface should not come in contact with any other objects. (We advise you to store them in the container in which they were shipped.) (4) Environmental conditions : - Do not leave them for more than 160hrs. at 70C. - Should not be left for more than 48hrs. at -20C. Safety (1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned. (2) If any liquid leakes out of a damaged glass cell and comes in contact with the hands, wash off thoroughly with soap and water. Limited Warranty Unless agreed between EAST and customer, EAST will replace or repair any of its LCD modules which are found to be functionally defective when inspected in accordance with EAST LCD acceptance standards (copies available upon request) for a period of one year from date of shipments. Cosmetic/visual defects must be returned to EAST within 90 days of shipment. Confirmation of such date shall be based on freight documents. The warranty liability of EAST limited to repair and/or replacement on the terms set forth above. EAST will not be responsible for any subsequent or consequential events. Return LCM under warranty EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com Fax: 86-755-83421997 Http//www.eastet.com 11 LCD MODULE www..com ET12864CV3 2006-04-06 No warranty can be granted if the precautions stated above have been disregarded. The typical examples of violations are : - Broken LCD glass. - PCB eyelet's damaged or modified. - PCB conductors damaged. - Circuit modified in any way, including addition of components. - PCB tampered with by grinding, engraving or painting varnish. - soldering to or modifying the bezel in any manner. Module repairs will be invoiced to the customer upon mutual agreement. Modules must be returned with sufficient description of the failures or defects. Any connectors or cable installed by the customer must be removed completely without damaging the PCB's eyelet, conductors and terminals. EAST ET TECHNOLOGY CO., LTD. Tel: 86-755-83427955 61332400 E-mail: east@eastet .com Fax: 86-755-83421997 Http//www.eastet.com 12 |
Price & Availability of ET12864CV3 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |