|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Instruction Sheet CHAMP* Right-Angle-Mount and Vertical-Mount Printed Circuit (PC) Board Connectors 408-7672 (was IS 7672) 09 AUG 06 Rev A Shielded Right-Angle-Mount Connector Vertical-Mount Connector Shielded Contact Tines (Typ) Unshielded 2.16 [.085] (Typ) Unshielded RECEPTACLE CONNECTORS CONNECTOR POSITIONS RIGHT-ANGLE UNSHIELDED SHIELDED VERTICAL UNSHIELDED SHIELDED PLUG CONNECTORS RIGHT-ANGLE VERTICAL UNSHIELDED 14 552738 --553119, 553121, 552212 --- 552739 552209 24 552740, 552791{ 553811, 554923, 555139 553448, 553815, 552224 554501 552741 552221 36 552742, 555493 554907, 555119, 555233, 555520 552235 554145, 554400 552743 552232 50 552725, 554663, 554841, 555492 552744 553813, 554901, 555057, 555149 --- 552118 554216, 554217 552726 552116 64 552246 --- 552745 552243 NOTE: Right-Angle-Mount Plug and Receptacle Connectors are available in standard pin orientation and reverse pin orientation. {For IEEE 488-1975 applications. Figure 1 2. DESCRIPTION 1. INTRODUCTION (Figure 1) This instruction sheet covers the CHAMP Right-Angle-Mount and Vertical-Mount PC Board Connectors (unshielded and shielded). These instructions include connector description and connector mounting procedures. Read this and all referenced material thoroughly before installing any connectors. NOTE Plug and receptacle connectors consist of polarized housings which are preloaded with solder-tine contacts on 2.16 mm [.085 in.] centers. They are available with 14, 24, 36, 50, and 64 contact positions that are arranged in two opposing rows. Vertical-mount connectors feature straight contact tines with 4.29 mm [.169 in.] between rows. The connectors may be installed on 1.57-3.18 mm [.062-.125 in.] thick pc boards. Shielded connectors have 2.54 and 5.08 mm [.100 and .200 in.] tail lengths. The 2.54 mm [.100 in.] tail can only be used on 1.57 mm [.062 in.] thick pc boards. This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.tycoelectronics.com LOC B Dimensions are in millimeters [with inch equivalents in brackets]. Figures are for identification only and are not drawn to scale. Reasons for reissue are provided in Section 5, REVISION SUMMARY. E2006 Tyco Electronics Corporation, Harrisburg, PA TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 1 of 3 All International Rights Reserved Tyco is a trademark. *Trademark Other products, logos, and company names used are the property of their respective owners. CHAMP Right-Angle-Mount and Vertical-Mount PC Board Connectors Right-angle-mount connectors are available for standard or reverse pin orientation on the pc board, refer to Figure 3 for application pin location. The contacts feature 90 bent contact tines with 4.29 mm [.169 in.] between rows. The connectors may be installed on 1.57-3.18 mm [.062-.125 in.] thick pc boards. Shielded connectors have a 3.99 mm [.157 in.] tail length, which is not suitable for 3.18 mm [.125 in.] thick pc boards. Shielded CHAMP Connectors afford excellent protection from Electromagnetic Interference (EMI) or electrostatic discharge to sensitive circuitry. These connectors are intermateable with existing connectors for cable-to-pc board applications. Refer to Instruction Sheet 7564 for cable connector information. All connectors have mounting flanges for attachment to the pc board and/or mating connector. Refer to instruction sheet 408-3160 for hardware information. 408-7672 Standard Orientation Reverse Orientation Pin No. 1 Pin No. 1 Pin No. 1 Hole for Reverse Orientation Pin No. 1 Hole for Standard Orientation Right-Angle-Mount Connector Rotate 3. CONNECTOR MOUNTING PROCEDURES CAUTION BEFORE attempting to install connector on the pc board, CLOSELY inspect for deformed broken contacts. First Row Started Into Holes PC Board NOTE Care must be used when installing these connectors; otherwise, the contact tines may be damaged. Also, correct orientation of the connector pin pattern with the pc board pattern should be checked. Vertical-Mount Connector Rotate The following procedures are recommended for shielded and unshielded connectors: First Row Started 1. Hold connector at a slight angle to the pc board and start one row of contacts into the contact holes. See Figure 2. 2. Rotate the connector until contact tines are aligned with opposite row of holes on pc board. 3. Make sure contact tines have started entrance into the holes, then push connector straight down until the standoffs bottom on the pc board. Into Holes PC Board Figure 2 4. Inspect contacts to make certain none have been deformed. All contact tines MUST extend through the pc board a minimum of 0.81 mm [.032 in.] for a good fillet. 5. Secure connector to pc board with CHAMP connector approved hardware, or the appropriate hardware kit selected for mating connectors. 2 of 3 Rev A CHAMP Right-Angle-Mount and Vertical-Mount PC Board Connectors 6. Solder contact tines to the pc board using high density wave solderable applications, or a standard reflow soldering technique. 408-7672 Screw Lock Kit 4. PANEL MOUNTING Either the plug or receptacle right-angle-mount or vertical-mount connector may be REAR panel mounted (see Figure 3). NOTE Panel thickness affects connector mating and hardware fastening. Consult reference documents or Tyco Electronics Engineering for application requirements. Front of Panel Screw 5. REVISION SUMMARY S Updated document to corporate requirements S General update to format S Deleted obsolete part numbers from table in Figure 1 Standoff Figure 3 Rev A 3 of 3 |
Price & Availability of 552212-1 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |