 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Integrated Circuit Systems, Inc. ICS950910 Programmable Timing Control HubTM for P4TM Recommended Application: VIA P4X/P4M/KT/KN266/333 style chipsets. Output Features: * 1 - Pair of differential CPU clocks @ 3.3V (CK408)/ 1 - Pair of differential open drain CPU clocks (K7) * 1 - Pair of differential push pull CPU_CS clocks @ 2.5V * 3 - AGP @ 3.3V * 7 - PCI @ 3.3V * 1 - 48MHz @ 3.3V fixed * 1 - 24_48MHz @ 3.3V * 2 - REF @ 3.3V, 14.318MHz Key Specifications: * CPU_CS - CPUT/C: <250ps * CPU_CS - AGP: <250ps * CPU - DDR: <250ps * PCI - PCI: <500ps * CPU - PCI: Min = 1.0ns, Typ = 2.0ns, Max = 4.0ns Features/Benefits: * Programmable output frequency. * Programmable output divider ratios. * Programmable output rise/fall time. * Programmable output skew. * Programmable spread percentage for EMI control. * DDR output buffer supports up to 200MHz. * Watchdog timer technology to reset system if system malfunctions. * Programmable watch dog safe frequency. * Support I2C Index read/write and block read/write operations. * Uses external 14.318MHz crystal. Frequency Table Bit2 Bit7 FS3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Bit6 FS2 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 Bit5 FS1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 Bit4 FS0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 CPU MHz 105.00 140.00 210.00 174.99 80.00 106.66 160.00 133.33 100.00 133.33 200.00 166.66 100.00 133.33 200.00 166.66 AGP MHz 70.00 70.00 70.00 70.00 53.34 53.34 53.34 53.34 66.67 66.67 66.67 66.67 66.67 66.67 66.67 66.67 PCI MHz 35.00 35.00 35.00 35.00 26.66 26.66 26.66 26.66 33.33 33.33 33.33 33.33 33.33 33.33 33.33 33.33 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0 - 0.6% Down Spread 0 - 0.6% Down Spread 0 - 0.6% Down Spread 0 - 0.6% Down Spread Spread % Pin Configuration *FS0/REF0 1 GND 2 X1 3 X2 4 VDDAGP 5 *MODE/AGPCLK0 6 *SEL_408/K7/AGPCLK1 7 *(PCI_STOP#)AGPCLK2 8 GNDAGP 9 **FS1/PCICLK_F 10 ***PCICLK1 11 GNDPCI 13 PCICLK3 14 PCICLK4 15 VDDPCI 16 PCICLK5 17 *(CLK_STOP#)PCICLK6 18 GND48 19 *FS3/48MHz 20 Output Current Ioh = 4* I REF Ioh = 6* I REF Voh @ Z 56 Vtt_PWRGD#**/REF1 55 VDDREF 54 GND 53 CPUCLKT/CPUCLKODT 52 CPUCLKC/CPUCLKODC 51 VDDCPU3.3 50 VDDCPU2.5 49 CPUC_CS 48 CPUT_CS 47 GND 46 FBOUT ICS950910 *MULTSEL/PCICLK2 12 45 BUF_IN 44 DDRT0 43 DDRC0 42 DDRT1 41 DDRC1 40 VDD2.5 39 GND 38 DDRT2 37 DDRC2 36 DDRT3 35 DDRC3 34 VDD2.5 33 GND 32 DDRT4 31 DDRC4 30 DDRT5 29 DDRC5 MULTISEL0 Board Target Trace/Term Z 50 ohms 50 ohms Reference R, Iref = VDD/(3*Rr) Rr = 221 1%, Iref = 5.00mA Rr = 475 1%, Iref = 2.32mA *FS2/24_48MHz 21 AVDD48 22 VDD 23 GND 24 IREF 25 *(PD#)RESET# 26 SCLK 27 SDATA 28 0 1 1.0V @ 50 0.7V @ 50 56-SSOP * Internal Pull-Up Resistor ** Internal Pull-Down Resistor *** A 120k pull-down resistor to GND is needed on this pin. 0735B--09/21/07 Integrated Circuit Systems, Inc. ICS950910 Pin Description PIN # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PIN NAME *FS0/REF0 GND X1 X2 VDDAGP *MODE/AGPCLK0 *SEL_408/K7/AGPCLK1 *(PCI_STOP#)AGPCLK2 GNDAGP **FS1/PCICLK_F ***PCICLK1 *MULTSEL/PCICLK2 GNDPCI PCICLK3 PCICLK4 VDDPCI PCICLK5 *(CLK_STOP#)PCICLK6 GND48 *FS3/48MHz *FS2/24_48MHz AVDD48 VDD GND IREF PIN TYPE I/O PWR IN OUT PWR I/O I/O I/O PWR I/O I/O I/O PWR OUT OUT PWR OUT I/O PWR I/O I/O PWR PWR PWR OUT DESCRIPTION Frequency select latch input pin / 14.318 MHz reference clock. Ground pin. Crystal input, Nominally 14.318MHz. Crystal output, Nominally 14.318MHz Power supply for AGP clocks, nominal 3.3V Function select latch input pin, 1=Desktop Mode, 0=Mobile Mode / AGP clock output. CPU output type select latch input pin 0= K7, 1= CK408 / AGP clock output. Stops all PCICLKs besides the PCICLK_F clocks at logic 0 level, when input low. This input is activated by the MODE selection pin / AGP clock output. Ground pin for the AGP outputs Frequency select latch input pin / 3.3V PCI free running clock output. Memory type select latch input pin 0= DDR, 1= PC133 SDRAM / 3.3V PCI clock output. 3.3V LVTTL input for selection the current multiplier for CPU outputs / 3.3V PCI clock output. Ground pin for the PCI outputs PCI clock output. PCI clock output. Power supply for PCI clocks, nominal 3.3V PCI clock output. Stops all CPU, DDR/SDRAM and FB_OUT clocks at logic 0 level, when input low. This input is activated by the MODE selection pin / PCI clock output. Ground pin for the 48MHz outputs Frequency select latch input pin / Fixed 48MHz clock output. 3.3V Frequency select latch input pin / Fixed 24 or 48MHz clock output. 3.3V. Power for 24/48MHz outputs and fixed PLL core, nominal 3.3V Power supply, nominal 3.3V Ground pin. This pin establishes the reference current for the CPUCLK pairs. This pin requires a fixed precision resistor tied to ground in order to establish the appropriate current. 26 *(PD#)RESET# I/O Asynchronous active low input pin used to power down the device into a low power state. This input is activated by the MODE selection pin / Real time system reset signal for frequency gear ratio change or watchdog timer timeout. This signal is active low. Clock pin of I2C circuitry 5V tolerant Data pin for I2C circuitry 5V tolerant 27 28 SCLK SDATA IN I/O * Internal Pull-Up Resistor ** Internal Pull-Down Resistor *** A 120k pull-down resistor to GND is needed on this pin. 0735B--09/21/07 2 Integrated Circuit Systems, Inc. ICS950910 Pin Description (Continued) PIN # 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 PIN NAME DDRC5 DDRT5 DDRC4 DDRT4 GND VDD2.5 DDRC3 DDRT3 DDRC2 DDRT2 GND VDD2.5 DDRC1 DDRT1 DDRC0 DDRT0 BUF_IN FBOUT GND CPUT_CS CPUC_CS VDDCPU2.5 VDDCPU3.3 CPUCLKC/CPUCLKODC PIN TYPE OUT OUT OUT OUT PWR PWR OUT OUT OUT OUT PWR PWR OUT OUT OUT OUT IN OUT PWR OUT OUT PWR PWR OUT DESCRIPTION "Complimentary" Clock of differential pair output. "True" Clock of differential pair output. "Complimentary" Clock of differential pair output. "True" Clock of differential pair output. Ground pin. Power supply, nominal 2.5V "Complimentary" Clock of differential pair output. "True" Clock of differential pair output. "Complimentary" Clock of differential pair output. "True" Clock of differential pair output. Ground pin. Power supply, nominal 2.5V "Complimentary" Clock of differential pair output. "True" Clock of differential pair output. "Complimentary" Clock of differential pair output. "True" Clock of differential pair output. Input Buffers for memory outputs. Memory feed back output. Ground pin. True clock of differential pair 2.5V push-pull CPU outputs. Complimentary" clocks of differential pair 2.5V push-pull CPU outputs. Power pin for the CPUCLKs. 2.5V Power pin for the CPUCLKs. 3.3V "Complementary" clocks of differential pair CPU outputs. These are current mode outputs. External resistors are required for voltage bias / "Complementary" clocks of differential pair CPU outputs. These open drain outputs need an external 1.5V pull-up / 2.5V CPU clock output. "True" clocks of differential pair CPU outputs. These are current mode outputs. External resistors are required for voltage bias / "True" clocks of differential pair CPU outputs. These open drain outputs need an external 1.5V pull-up / 2.5V CPU clock output. Ground pin. Ref, XTAL power supply, nominal 3.3V This 3.3V LVTTL input is a level sensitive strobe used to determine when latch inputs are valid and are ready to be sampled. This is an active low input. / 14.318 MHz reference clock. 53 54 55 56 CPUCLKT/CPUCLKODT GND VDDREF Vtt_PWRGD#**/REF1 OUT PWR PWR IN 0735B--09/21/07 3 Integrated Circuit Systems, Inc. ICS950910 General Description The ICS950910 is a single chip clock solution for desktop designs using the VIA P4X/P4M/KT/KN266/333 style chipsets with PC133 or DDR memory. The ICS950910 is part of a whole new line of ICS clock generators and buffers called TCHTM (Timing Control Hub). This part incorporates ICS's newest clock technology which offers more robust features and functionality. Employing the use of a serially programmable I2C interface, this device can adjust the output clocks by configuring the frequency setting, the output divider ratios, selecting the ideal spread percentage, the output skew, the output strength, and enabling/disabling each individual output clock. M/N control can configure output frequency with resolution up to 0.1MHz increment. Block Diagram FBOUT Power Groups Pin Number VDD 55 5 16 22 23 34, 40 50 51 0735B--09/21/07 GND 2 9 13 19 24 33, 39 47 54 Description Xtal, Ref AGP [0:2], CPU digital, CPU PLL PCI [0:5], PCI_F outputs 48MHz, Fix Digital, Fix Analog Master clock, CPU Analog DDR/SDR outputs 2.5V CPUT/C_CS output 3.3V CPUT/C & CPUOD_T/C 4 Integrated Circuit Systems, Inc. ICS950910 General I2C serial interface information How to Write: Controller (host) sends a start bit. Controller (host) sends the write address D2 (H) ICS clock will acknowledge Controller (host) sends the begining byte location = N ICS clock will acknowledge Controller (host) sends the data byte count = X ICS clock will acknowledge Controller (host) starts sending Byte N through Byte N + X -1 (see Note 2) * ICS clock will acknowledge each byte one at a time * Controller (host) sends a Stop bit * * * * * * * * How to Read: * * * * * * * * * * * * * * Controller (host) will send start bit. Controller (host) sends the write address D2 (H) ICS clock will acknowledge Controller (host) sends the begining byte location = N ICS clock will acknowledge Controller (host) will send a separate start bit. Controller (host) sends the read address D3 (H) ICS clock will acknowledge ICS clock will send the data byte count = X ICS clock sends Byte N + X -1 ICS clock sends Byte 0 through byte X (if X(H) was written to byte 8). Controller (host) will need to acknowledge each byte Controllor (host) will send a not acknowledge bit Controller (host) will send a stop bit Index Block Write Operation Controller (Host) starT bit T Slave Address D2(H) WR WRite Beginning Byte = N ACK Data Byte Count = X ACK Beginning Byte N ACK X Byte ICS (Slave/Receiver) Index Block Read Operation Controller (Host) T starT bit Slave Address D2(H) WR WRite Beginning Byte = N ACK RT Repeat starT Slave Address D3(H) RD ReaD ACK Data Byte Count = X ACK Beginning Byte N ACK X Byte ICS (Slave/Receiver) ACK ACK Byte N + X - 1 ACK P stoP bit Byte N + X - 1 N P Not acknowledge stoP bit *See notes on the following page. 0735B--09/21/07 5 Integrated Circuit Systems, Inc. ICS950910 Byte 0: Functionality and frequency select register (Default=0) Bi t Bit2 Description Bit7 Bit6 Bit5 Bit4 CPUCLK AGPCLK PCICLK MHz MHz MHz FS 3 FS 2 FS 1 FS 0 Spread % +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread +/- 0.30% Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0.3 % Center Spread 0 - 0.6% Down Spread 0 - 0.6% Down Spread 0 - 0.6% Down Spread 0 - 0.6% Down Spread PWD Bi t (2,7:4) Bi t 3 Bi t 1 Bi t 0 0 0 0 0 0 102.00 68.00 34.00 0 0 0 0 1 105.00 70.00 35.00 0 0 0 1 0 108.00 72.00 36.00 0 0 0 1 1 111.00 74.00 27.00 0 0 1 0 0 114.00 76.00 38.00 0 0 1 0 1 117.00 78.00 39.00 0 0 1 1 0 120.00 80.00 40.00 0 0 1 1 1 123.00 82.00 41.00 0 1 0 0 0 126.00 72.00 36.00 0 1 0 0 1 130.00 74.30 37.10 0 1 0 1 0 133.90 66.95 33.48 0 1 0 1 1 140.00 70.00 35.00 0 1 1 0 0 144.00 72.00 36.00 0 1 1 0 1 148.00 74.00 37.00 0 1 1 1 0 152.00 76.00 38.00 0 1 1 1 1 156.00 78.00 39.00 1 0 0 0 0 105.00 70.00 35.00 1 0 0 0 1 140.00 70.00 35.00 1 0 0 1 0 210.00 70.00 35.00 1 0 0 1 1 174.99 70.00 35.00 1 0 1 0 0 80.00 53.34 26.66 1 0 1 0 1 106.66 53.34 26.66 1 0 1 1 0 160.00 53.34 26.66 1 0 1 1 1 133.33 53.34 26.66 1 1 1 0 0 100.00 66.67 33.33 1 1 1 0 1 133.33 66.67 33.33 1 1 1 1 0 200.00 66.67 33.33 1 1 1 1 1 166.66 66.67 33.33 1 1 0 0 0 100.00 66.67 33.33 1 1 0 0 1 133.33 66.67 33.33 1 1 0 1 0 200.00 66.67 33.33 1 1 0 1 1 166.66 66.67 33.33 0 - Frequency is selected by hardware select, latched inputs 1 - Frequency is selected by Bit 2,7:4 0 - Normal 1 - Spread spectrum enable 0 - Running 1 - Tristate all outputs Note 1 0 1 0 Notes: 1. Default at power-up will be for latched logic inputs to define frequency, as displayed by Bit 3. Mode Pin - Power Management Input Control MODE, Pin 6 (Latched Input) 0 1 0735B--09/21/07 Pin 26 PD# (Input) RESET# (Output) Pin 18 CPU_STOP# (Input) PCICLK5 (Output) Pin 8 PCI_STOP# (Input) AGP2 (Output) 6 Integrated Circuit Systems, Inc. ICS950910 Byte 1: CPU Active/Inactive Register (1 = enable, 0 = disable) Bit Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Pin# 29 10 30 31 32 53, 52 48, 49 PWD 1 1 1 1 1 1 1 1 Description DDRC5 (Active/Inactive) PCICLK_F (Active/Inactive) DDRT5 (Active/Inactive) DDRC4 (Active/Inactive) (Reserved) DDRT4 (Active/Inactive) CPUCLKT/C_CS (Active/Inactive) CPUCLKT/C_CS (Active/Inactive) Byte 2: PCI Active/Inactive Register (1 = enable, 0 = disable) Bit Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Pin# 46 18 17 15 14 12 11 53, 52 PWD 1 1 1 1 1 1 1 1 Description FB_OUT Free running control; 1 = free running; 0 = not free running PCICLK6 (Active/Inactive) PCICLK5 (Active/Inactive) PCICLK4 (Active/Inactive) PCICLK3 (Active/Inactive) PCICLK2 (Active/Inactive) PCICLK1 (Active/Inactive) CPUCLKT/C Free running control; 1 = free running; 0 = not free running Byte 3: Active/Inactive Register (1 = enable, 0 = disable) Bit Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0 Pin# 46 56 48, 49 8 7 6 PWD 1 1 1 1 1 1 1 1 Description FB_OUT (Active/Inactive) SEL 24_48, 0=24Mhz 1=48MHz DDR free running control; 1 = free running; 0 not free running REF1 (Active/Inactive) CPUC/T_CS free running control; 1 = free running; 0 not free running AGPCLK 2 (Active/Inactive) AGPCLK 1 (Active/Inactive) AGPCLK 0 (Active/Inactive) Byte 4: Frequency Select Active/Inactive Register (1 = enable, 0 = disable) Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Pin# 20 21 1 PWD X X X X 1 1 1 Description Latched FS3 Latched FS2 Latched FS1 Latched FS0 48MHz (Active/Inactive) 24_48MHz (Active/Inactive) (Reserved) REF0 (Active/Inactive) 0735B--09/21/07 7 Integrated Circuit Systems, Inc. ICS950910 Byte 5: Peripheral Active/Inactive Register (1 = enable, 0 = disable) Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Pin# 35 36 37 38 41 42 43 44 PWD 1 1 1 1 1 1 1 1 Description DDRC3 (Active/Inactive) DDRT3 (Active/Inactive) DDRC2 (Active/Inactive) DDRT2 (Active/Inactive) DDRC1 (Active/Inactive) DDRT1 (Active/Inactive) DDRC0 (Active/Inactive) DDRT0 (Active/Inactive) Byte 6: Vendor ID Register (1 = enable, 0 = disable) Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name Revision ID Bit3 Revision ID Bit2 Revision ID Bit1 Revision ID Bit0 Vendor ID Bit3 Vendor ID Bit2 Vendor ID Bit1 Vendor ID Bit0 PWD X X X X 0 0 0 1 Description Revision ID values will be based on individual device's revision (Reserved) (Reserved) (Reserved) (Reserved) Byte 7: Revision ID and Device ID Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name Device ID7 Device ID6 Device ID5 Device ID4 Device ID3 Device ID2 Device ID1 Device ID0 PWD Description 0 0 0 Device ID values will be based on individual device 1 "01h" in this case. 0 1 1 1 Byte 8: Byte Count Read Back Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name Byte7 Byte6 Byte5 Byte4 Byte3 Byte2 Byte1 Byte0 PWD Description 0 0 0 Note: Writing to this register will configure byte count and how 0 many bytes will be read back, default is 0FH = 15 bytes. 1 1 1 1 0735B--09/21/07 8 Integrated Circuit Systems, Inc. ICS950910 Byte 9: Watchdog Timer Count Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name WD7 WD6 WD5 WD4 WD3 WD2 WD1 WD0 PWD Description 0 0 0 The decimal representation of these 8 bits correspond to X * 1 290ms the watchdog timer will wait before it goes to alarm mode and reset the frequency to the safe setting. Default at power up is 0 16 * 290ms = 4.6 seconds. 0 0 0 Byte 10: Programming Enable bit 8 Watchdog Control Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name Program Enable WD Enable WD Alarm S F4 S F3 S F2 S F1 S F0 PWD 0 0 0 0 0 0 0 0 Description Programming Enable bit 0 = no programming. Frequencies are selected by HW latches or Byte0 1 = enable all I2C programing. Software Watchdog Enable bit. This bit will over write WDEN latched value. 0 = disable, 1 = Enable. Watchdog Alarm Status 0 = normal 1= alarm status Watchdog safe frequency bits. Writing to these bits will configure the safe frequency corrsponding to Byte 0 Bit 2, 7:4 table Byte 11: VCO Frequency M Divider (Reference divider) Control Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name Ndiv 8 Mdiv 6 Mdiv 5 Mdiv 4 Mdiv 3 Mdiv 2 Mdiv 1 Mdiv 0 PWD X X X X X X X X Description N divider bit 8 The decimal respresentation of Mdiv (6:0) corresposd to the reference divider value. Default at power up is equal to the latched inputs selection. Byte 12: VCO Frequency N Divider (VCO divider) Control Register Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0735B--09/21/07 Name Ndiv 7 Ndiv 6 Ndiv 5 Ndiv 4 Ndiv 3 Ndiv 2 Ndiv 1 Ndiv 0 PWD Description X X X The decimal representation of Ndiv (8:0) correspond to the X VCO divider value. Default at power up is equal to the latched inputs selecton. Notice Ndiv 8 is located in Byte 11. X X X X 9 Integrated Circuit Systems, Inc. ICS950910 Byte 13: Spread Spectrum Control Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name SS 7 SS 6 SS 5 SS 4 SS 3 SS 2 SS 1 SS 0 PWD Description X X The Spread Spectrum (12:0) bit will program the spread X precentage. Spread precent needs to be calculated based on the X VCO frequency, spreading profile, spreading amount and spread X frequency. It is recommended to use ICS software for spread X programming. Default power on is latched FS divider. X X Byte 14: Spread Spectrum Control Register Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Reserved Reserved Reserved SS 12 SS 11 SS 10 SS 9 SS 8 PWD X X X X X X X X Description Reserved Reserved Reserved Spread Spectrum Bit 12 Spread Spectrum Bit 11 Spread Spectrum Bit 10 Spread Spectrum Bit 9 Spread Spectrum Bit 8 Byte 15: Output Divider Control Register Bit Bit 7 B it 6 Bit 5 Bit 4 Bit 3 Bit 2 B it 1 Bit 0 Name CPU Div 3 CPU Div 2 CPU Div 1 CPU Div 0 CPU Div 3 CPU Div 2 CPU Div 1 CPU Div 0 PWD 0 1 0 1 0 1 0 1 Description CPUCLKC/T clock divider ratio can be configured via these 4 bits individually. For divider selection table refer to Table 1. Default at power up is latched FS divider. CPUCLKT/C_CS clock divider ratio can be configured via these 4 bits individually. For divider selection table refer to Table 1. Default at power up is latched FS divider. Byte 16: Output Divider Control Register Bit Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name AGP Div 3 AGP Div 2 AGP Div 1 AGP Div 0 Reser ved Reser ved Reser ved Reser ved PWD 0 1 0 1 - Description AGP clock divider ratio can be configured via these 4 bits individually. For divider selection table refer to Table 1. Default at power up is latched FS divider. Reser ved 0735B--09/21/07 10 Integrated Circuit Systems, Inc. ICS950910 Byte 17: Output Divider Control Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name AGP_INV Reserved CPU_INV CPU_INV PWD 0 0 0 0 Description AGP Phase Inversion bit Reserved CPU T/C Phase Inversion bit CPUT/C_CS Phase Inversion bit PCI Div 3 PCI Div 2 PCI Div 1 PCI Div 0 1 0 0 1 PCI clock divider ratio can be configured via these 4 bits individually. For divider selection table refer to Table 2. Default at power up is latched FS divider. Table 1 Table 2 Div (3:2) Div (1:0) 00 01 10 11 00 /2 /3 /5 /7 01 /4 /6 /10 /14 10 /8 /12 /20 /28 11 /16 /24 /40 /56 Div (3:2) Div (1:0) 00 01 10 11 00 /4 /3 /5 /9 01 /8 /6 /10 /18 10 /16 /12 /20 /36 11 /32 /24 /40 /72 Byte 18: Group Skew Control Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name CPUCLKT/C_CS Group Skew Control CPUCLKT/C Group Skew Control AGPCLK Group Skew Control Reserved Reserved PWD 1 0 1 0 1 0 X X Description These 2 bits delay the CPUCLKT/C_CS with respect to CPUCLKT/C 00 = 0ps 01 = 250ps 10 = 500ps 11 =750ps These 2 bits delay the CPUCLKT/C clock with respect to CPUCLKT/C_CS 00 = 0ps 01 = 250ps 10 = 500ps 11 = 750ps These 2 bits delay the AGPCLK clocks with respect to CPUCLK 00 = 0ps 01 = 250ps 10 = 500ps 11 = 750ps Reserved Reserved Byte 19: Group Skew Control Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name Reserved PCICLK(5:0) Group Skew Control PWD Description 1 0 Reserved 0 0 1 These 4 bits can change the CPU to PCI (5:0) skew from 1.4ns 0 2.9ns. Default at power up is - 2.5ns. Each binary increment or decrement of Bits (3:0) will increase or decrease the delay of the 0 PCI clocks by 100ps. 0 0735B--09/21/07 11 Integrated Circuit Systems, Inc. ICS950910 Byte 20: Group Skew Control Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name PCICLK_F Group Skew Control PWD Description 1 These 4 bits can change the CPU to PCIF skew from 1.4ns 0 2.9ns. Default at power up is - 2.5ns. Each binary increment or decrement of Bit (3:0) will increase or decrease the delay of the 0 PCI clocks by 100ps. 0 1 0 Reserved 0 0 Reserved Byte 21: Slew Rate Control Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name CPUCLKT/C_CS Slew Rate Control CPUCLKT1/C1 Slew Rate Control CPUCLKT2/C2 Slew Rate Control AGP_0 Slew Rate Control PWD 0 1 0 1 0 1 0 1 Description CPUCLKT/C_CS clock slew rate control bits. 01 = strong:10 = normal; 00 = weak CPUCLKT1/C1 clock slew rate control bits. 01 = strong: 10= normal; 00 = weak CPUCLKT2/C2 clock slew rate control bits. 01 = strong: 10= normal; 00 = weak AGP_0 clock slew rate control bits. 01 = strong: 10 = normal; 00 = weak Byte 22: Slew Rate Control Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name AGP(2:1) Slew Rate Control PCICLK_F Slew Rate Control PCICLK(7:4) Slew Rate Control PCICLK(3:0) Slew Rate Control PWD 0 1 0 1 0 1 0 1 Description AGP(2:1) clock slew rate control bits. 01 = strong:10 = normal; 00 = weak PCICLK_F clock slew rate control bits. 01 = strong: 10= normal; 00 = weak PCICLK(7:4) clock slew rate control bits. 01 = strong: 10= normal; 00 = weak PCICLK(3:0) clock slew rate control bits. 01 = strong: 10 = normal; 00 = weak Byte 23: Slew Rate Control Register Bit Bi t 7 Bi t 6 Bi t 5 Bi t 4 Bi t 3 Bi t 2 Bi t 1 Bi t 0 Name REF Slew Rate Control IOAPIC(1:0) Slew Rate Control 48MHz Slew Rate Control 24_48MHz Slew Rate Control PWD 0 1 0 1 0 1 0 1 Description REF clock slew rate control bits. 01 = strong:10 = normal; 00 = weak IOAPIC(1:0) clock slew rate control bits. 01 = strong: 10= normal; 00 = weak 48MHz clock slew rate control bits. 01 = strong: 10= normal; 00 = weak 24_48MHz clock slew rate control bits. 01 = strong: 10 = normal; 00 = weak 0735B--09/21/07 12 Integrated Circuit Systems, Inc. ICS950910 Absolute Maximum Ratings Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Logic Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND -0.5 V to VDD +0.5 V Ambient Operating Temperature . . . . . . . . . . . . 0C to +70C Case Temperature . . . . . . . . . . . . . . . . . . . . . . . . 115C Storage Temperature . . . . . . . . . . . . . . . . . . . . . -65C to +150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only and functional operation of the device at these or any other conditions above those listed in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. Electrical Characteristics - Input/Supply/Common Output Parameters TA = 0 - 70C; Supply Voltage VDD = 3.3 V +/-5% PARAMETER SYMBOL VIH Input High Voltage Input Low Voltage VIL IIH Input High Current IIH IIL1 Input Low Current IIL2 IDD3.3OP Operating Supply Current IDD3.3OP Powerdown Current Input Frequency Pin Inductance Input Capacitance Clk Stabilization Delay1 tPHZ,tPLZ 1 2 1 CONDITIONS MIN 2 VSS - 0.3 TYP MAX VDD + 0.3 0.8 5.75 200 UNITS V V mA VIN = VDD; Inputs with no pull-down resistors VIN = VDD; Inputs with pull-down resistors VIN = 0 V; Inputs with no pull-up resistors VIN = 0 V; Inputs with pull-up resistors CL = Full load; Select @ 100 MHz CL =Full load; Select @ 133 MHz IREF=2.32 mA VDD = 3.3 V Logic Inputs Output pin capacitance X1 & X2 pins From PowerUp or deassertion of PowerDown to 1st clock. Output enable delay (all outputs) Output disable delay (all outputs) A mA -5.75 -200 228 220 156 159 12 14.318 360 360 45 7 5 6 45 2.1 1 1 12 12 A mA mA mA MHz nH pF pF pF ms ns ns IDD3.3PD Fi Lpin CIN COUT CINX TSTAB tPZH,tPZL 27 1,2 Guaranteed by design, not 100% tested in production. See timing diagrams for buffered and un-buffered timing requirements. 0735B--09/21/07 13 Integrated Circuit Systems, Inc. ICS950910 Electrical Characteristics - CPUCLKC/T (Current Mode) TA = 0 - 70C; VDD=3.3V +/-5%; CL = 10-20 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS Current Source Output 1 VO = Vx Zo Impedance Statistical measurement on single VHigh Voltage High ended signal using oscilloscope VLow Voltage Low Measurement on single ended Vovs Max Voltage signal using absolute value. Vuds Min Voltage Vcross(abs) Crossing Voltage (abs) Variation of crossing over all Crossing Voltage (var) d-Vcross edges VOL = 0.175V, VOH = 0.525V tr Rise Time tf VOH = 0.525V VOL = 0.175V Fall Time d-tr Rise Time Variation d-tf Fall Time Variation Measurement from differential dt3 Duty Cycle wavefrom tsk3 VT = 50% Skew 1 VT = 50% Jitter, Cycle to cycle tjcyc-cyc 1 2 MIN 3000 660 -150 -450 250 TYP MAX UNITS 810 20 850 -15 380 22 850 150 1150 550 140 700 700 125 125 55 100 150 mV mV mV mV ps ps ps ps % ps ps 175 175 290 310 10 10 51 16 48 45 Guaranteed by design, not 100% tested in production. IOWT can be varied and is selectable thru the MULTSEL pin. Electrical Characteristics - CPUCLKODC/T TA = 0 - 70C; VDD = 1.7 V +/-5%; CL = 5 pF (unless otherwise stated) PARAMETER Output High Voltage Output Low Voltage Output Low Current Rise Time1 Fall Time1 Differential voltageAC1 Differential voltageDC1 Differential Crossover Voltage1 Duty Cycle1 Skew1 Jitter Diff, Cycle-toSYMBOL VOH2B VOL2B IOL2B tr2B tf2B VDIF VDIF VX dt2B tsk2B VT = 50% VT = 50% CONDITIONS Termination to Vpull-up(external) Termination to Vpull-up(external) VOL = 0.3 V VOL = 20%, VOH = 80% VOH = 80%, VOL = 20%, MIN 1 18 0.38 0.44 0.4 0.2 550 45 1200 51.5 140 60 100 -250 1250 55 200 250 250 250 0.9 0.9 TYP MAX 1.2 0.4 UNITS V V mA ns ns V V mV % ps ps ps ps tjcyc-cyc2B VT = VX cycle1 Jitter SE, Cycle-totjcyc-cyc2B VT = 1.0V cycle1 tjabs2B VT = 50% Jitter, Absolute1 Notes: 1 - Guaranteed by design, not 100% tested in production. 0735B--09/21/07 14 Integrated Circuit Systems, Inc. ICS950910 Electrical Characteristics - CPUT/C_CS TA = 0 - 70C; VDD=3.3V +/-5%; CL = 2 pF (unless otherwise stated) PARAMETER SYMBOL CONDITIONS IOH = -12 mA Output High Voltage VOH2B IOL = 12mA Output Low Voltage VOL2B VOH = 1.7V Output High Voltage IOH2B VOL = 0.7V Output Low Voltage IOL2B VOL = 0.4V, VOH = 2.0V tr2B Rise Time Differential Crossover Vx Note3 Voltage VT = 1.5V Duty Cycle d-t2B VT = 1.5V tjcyc-cyc2B Jitter, Cycle to cycle 2 MIN 2 TYP MAX 0.4 -19 19 0.91 45 45 48.7 62 1.6 55 55 100 UNITS V V mA mA ns % % ps IOWT can be varied and is selectable thru the MULTSEL pin. Electrical Characteristics- DDRT/C TA = 0 - 70C; VDD=3.3V +/-5%; CL = 30 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS IOH = -11 mA VOH3 Output High Voltage 3 IOL = 11 mA Output Low Voltage VOL 3 V OH = 2.0 V Output High Current IOH 3 VOL = 0.8 V Output Low Current IOL Rise Time Fall Time Duty Cycle Skew Jitter 1 MIN 2.4 TYP MAX 0.4 -12 UNITS V V mA ns ns % ps ps tr3 1 tf3 1 dt3 tsk1 1 1 tjcyc-cyc 1 20% to 80% 20% to 80% VT = 1.5 V VT = 1.5 V VT = 1.5 V 12 650 650 45 660 660 50.3 102 78 950 950 53 250 250 Guaranteed by design, not 100% tested in production. 0735B--09/21/07 15 Integrated Circuit Systems, Inc. ICS950910 Electrical Characteristics- PCICLK TA = 0 - 70C; VDD=3.3V +/-5%; CL = 30 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS 1 Output Frequency FO 1 VO = VDD*(0.5) Output Impedance RDSP1 1 IOH = -1 mA Output High Voltage VOH 1 IOL = 1 mA Output Low Voltage VOL V OH@MIN = 1.0 V 1 Output High Current IOH V OH@MAX = 3.135 V VOL @MIN = 1.95 V 1 Output Low Current IOL VOL @MAX = 0.4 V 1 VOL = 0.4 V, VOH = 2.4 V Rise Time tr1 1 VOH = 2.4 V, VOL = 0.4 V Fall Time tf1 1 VT = 1.5 V Duty Cycle dt1 Skew Jitter 1 MIN 12 2.4 -33 TYP 33.33 MAX 55 0.55 -33 UNITS MHz V V mA mA ns ns % ps ps 30 0.5 0.5 45 1.8 1.6 52.4 239 205 38 2 2 55 500 250 tsk1 1 VT = 1.5 V VT = 1.5 V 1 tjcyc-cyc Guaranteed by design, not 100% tested in production. Electrical Characteristics- AGP TA = 0 - 70C; VDD=3.3V +/-5%; CL = 30 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS 1 Output Frequency FO 1 VO = VDD*(0.5) Output Impedance RDSP1 1 IOH = -1 mA Output High Voltage VOH 1 IOL = 1 mA Output Low Voltage VOL VOH = 1.0 V 1 Output High Current IOH VOH = 3.135 V VOL = 1.95 V 1 Output Low Current IOL VOL = 0.4 V 1 VOL = 0.4 V, VOH = 2.4 V Rise Time tr1 1 VOH = 2.4 V, VOL = 0.4 V Fall Time tf1 Duty Cycle Skew Jitter 1 MIN 12 2.4 -33 TYP 66.66 MAX 55 0.55 -33 UNITS MHz V V mA mA ns ns % ps ps 30 0.5 0.5 45 1.5 1.28 52.9 40 113 38 2 2 55 500 250 dt1 1 1 VT = 1.5 V VT = 1.5 V VT = 1.5 V tsk1 1 tjcyc-cyc Guaranteed by design, not 100% tested in production. 0735B--09/21/07 16 Integrated Circuit Systems, Inc. ICS950910 Electrical Characteristics - VCH, 48MHz DOT, 48MHz, USB TA = 0 - 70C; VDD=3.3V +/-5%; CL = 20 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS FO1 Output Frequency 1 VO = VDD*(0.5) Output Impedance RDSP1 1 IOH = -1 mA Output High Voltage VOH 1 IOL = 1 mA Output Low Voltage VOL VOH = 1.0 V 1 Output High Current IOH VOH = 3.135 V VOL = 1.95 V 1 Output Low Current IOL VOL = 0.4 V 1 VOL = 0.4 V, VOH = 2.4 V 48MHz Rise Time tr1 1 VOH = 2.4 V, VOL = 0.4 V 48MHz Fall Time tf1 1 VOL = 0.4 V, VOH = 2.4 V 24MMz Rise Time tr1 1 VOH = 2.4 V, VOL = 0.4 V 24MHz Fall Time tf1 1 VT = 1.5 V 48 MHz Duty Cycle dt1 1 VT = 1.5 V 48MHz Duty Cycle dt1 1 VT = 1.5 V 48 MHz Jitter tjcyc-cyc 1 VT = 1.5 V 24MHz Jitter tjcyc-cyc 1 MIN 12 2.4 -29 TYP 48 48 MAX 55 0.55 -23 UNITS MHz V V mA mA ns ns ns ns % % ps ps 29 0.5 0.5 1 1 45 45 1.25 1.27 1.26 1.28 52.5 51.4 124 111 27 2 2 2 2 55 55 350 350 Guaranteed by design, not 100% tested in production. ** USB is 180 degrees phase different to DOT Electrical Characteristics - REF TA = 0 - 70C; VDD=3.3V +/-5%; CL = 30 pF (unless otherwise specified) PARAMETER SYMBOL CONDITIONS FO1 Output Frequency VO = VDD*(0.5) Output Impedance RDSP11 IOH = -1 mA Output High Voltage VOH1 1 IOL = 1 mA Output Low Voltage VOL VOH = 1.0 V Output High Current IOH1 VOH = 3.135 V VOL = 1.95 V Output Low Current IOL1 VOL = 0.4 V 1 VOL = 0.4 V, VOH = 2.4 V Rise Time tr1 1 VOH = 2.4 V, VOL = 0.4 V Fall Time tf1 1 VT = 1.5 V Duty Cycle dt1 Jitter 1 MIN 20 2.4 -29 TYP 14.32 MAX 60 0.4 -23 UNITS MHz V V mA mA ns ns % ps 29 1 1 45 1.92 1.92 54.1 245 27 4 4 55 500 tjcyc-cyc1 VT = 1.5 V Guaranteed by design, not 100% tested in production. 0735B--09/21/07 17 Integrated Circuit Systems, Inc. ICS950910 Shared Pin Operation Input/Output Pins The I/O pins designated by (input/output) serve as dual signal functions to the device. During initial power-up, they act as input pins. The logic level (voltage) that is present on these pins at this time is read and stored into a 5-bit internal data latch. At the end of Power-On reset, (see AC characteristics for timing values), the device changes the mode of operations for these pins to an output function. In this mode the pins produce the specified buffered clocks to external loads. To program (load) the internal configuration register for these pins, a resistor is connected to either the VDD (logic 1) power supply or the GND (logic 0) voltage potential. A 10 Kilohm (10K) resistor is used to provide both the solid CMOS programming voltage needed during the power-up programming period and to provide an insignificant load on the output clock during the subsequent operating period. Figure 1 shows a means of implementing this function when a switch or 2 pin header is used. With no jumper is installed the pin will be pulled high. With the jumper in place the pin will be pulled low. If programmability is not necessary, than only a single resistor is necessary. The programming resistors should be located close to the series termination resistor to minimize the current loop area. It is more important to locate the series termination resistor close to the driver than the programming resistor. Programming Header Via to Gnd Device Pad Via to VDD 2K W 8.2K W Clock trace to load Series Term. Res. Fig. 1 0735B--09/21/07 18 Integrated Circuit Systems, Inc. ICS950910 Power Down Waveforms 0ns 1 25ns 50ns 2 VCO Internal CPU 100MHz 3.3V 66MHz PCI 33MHz PD# REF 14.318MHZ 48MHZ Note 1. After PD# is sampled active (Low) for 2 consective rising edges of CPUCLKs, all the output clocks are driven Low on their next High to Low tranistiion. 2. Power-up latency <3ms. 3. Waveform shown for 100MHz Group Offset Waveforms 0ns 10ns 20ns 30ns 40ns Cycl e R epeat s CPU 66MHz CPU 100MHz CPU 133MHz 3.5V 66MHz PCI 33MHz APIC 16.7MHz REF 14.318MHz USB 48MHz Group Skews at Common Transition Edges GROUP CPU408 to CPUCS CPU Open Drain to CPUCS CPUCS to PCI CPU408 to PCI AGP to PCI 1 0735B--09/21/07 SYMBOL CPU CPU SCPU-PCI SCPU-PCI SAGP-PCI CONDITIONS 50% to 1.25V 50% to 1.25V 1.25 to 1.5V 1.25 to 1.5V 1.5 to 1.5V MIN 0 0 0 0 1.5 TYP 75 2.8 3.8 2.87 MAX 250 250 4 4 3.5 UNITS ps ns ns ns Guaranteed by design, not 100% tested in production. 19 Integrated Circuit Systems, Inc. ICS950910 N c L SYMBOL A A1 b c D E E1 e h L N INDEX AREA E1 E 12 D h x 45 a A A1 In Millimeters COMMON DIMENSIONS MIN MAX 2.41 2.80 0.20 0.40 0.20 0.34 0.13 0.25 SEE VARIATIONS 10.03 10.68 7.40 7.60 0.635 BASIC 0.38 0.64 0.50 1.02 SEE VARIATIONS 0 8 VARIATIONS D mm. MIN MAX 18.31 18.55 In Inches COMMON DIMENSIONS MIN MAX .095 .110 .008 .016 .008 .0135 .005 .010 SEE VARIATIONS .395 .420 .291 .299 0.025 BASIC .015 .025 .020 .040 SEE VARIATIONS 0 8 -Ce b SEATING PLANE .10 (.004) C N 56 10-0034 D (inch) MIN .720 MAX .730 Reference Doc.: JEDEC Publication 95, MO-118 300 mil SSOP Package Ordering Information ICS950910YFLF-T Example: ICS XXXX y F LF- T Designation for tape and reel packaging Lead Free (Optional) Package Type F = SSOP Revision Designator (will not correlate with datasheet revision) Device Type Prefix ICS = Standard Device 0735B--09/21/07 20 Integrated Circuit Systems, Inc. ICS950910 Revision History Rev. B Issue Date Description 09/21/07 Updated Pin 18 Typo. Page # 2 0735B--09/21/07 21 |
Price & Availability of ICS950910YFLF-T
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |