 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Series AMLDL-Z Up to 1000mA | LED Driver FEATURES: * * * * Step Down DC/DC LED driver Constant current output Wide (4:1) input voltage range High efficiency up to 95% * * * * Operating Temperature range -40C to +85C Open and Short LED Protection PWM/Digital and Analog Voltage dimming Remote ON/OFF Control Models Single output Model AMLDL-3030Z AMLDL-3035Z AMLDL-3050Z AMLDL-3060Z AMLDL-3070Z AMLDL-30100Z Input Voltage (V) 7-30 7-30 7-30 7-30 7-30 7-30 Output Voltage (V) Output Current (mA) 2-28 2-28 2-28 2-28 2-28 2-28 300 350 500 600 700 1000 Efficiency (%) 95 95 95 95 95 95 Package Type DIP14 DIP14 DIP16 DIP16 DIP16 DIP16 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range Filter Absolute Maximum Rating Peak Input Voltage time DC/DC ON (Leave open if not used) DC/DC OFF Maximum Remote pin drive current Quiescent Current in Shutdown mode On/Off Control (Digital Control) Minimum Switch ON/OFF time On/Off Control (Analog Dimming Control) (Leave open if not used) Drive with DC Voltage Control Voltage Range limits Maximum Analog pin drive current Nominal 24 Typical 7-30 Capacitor Maximum 40 500 Units VDC VDC ms ON -Open or 0.3V Output Specifications Parameters Current accuracy Output Voltage range Output current Short Circuit protection Output no load Protection Max load capacitance Temperature coefficient Ripple & Noise Conditions Typical 6 2-28 Maximum Units % VDC mA V input = 30V Vin - Vout >1.5V to 3V 300 Regulated at the rated current for each model Continuously 47 Ta = -40 to +85C 0.05 20MHz Bandwidth 250 F %/oC mV p-p General Specifications Parameters Switching frequency Operating temperature Storage temperature Conditions 100% load Typical 40 - 380 -40 to +85 -40 to +125 Maximum Units KHz o C o C www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 1 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver General Specifications (continued) Parameters Maximum case temperature Thermal Impedance Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum Soldering Temperature NOTES: Conditions Free air convection Typical +40 Free air convection Maximum 100 Units o C C/W o 95 % RH Non-Conductive Black Plastic (UL94-V0 rated) 2.6 (DIP14) g 6.2 (DIP 16) DIP 14 0.80 x 0.40 x 0.27 inches 20.32 x 10.16 x 6.88 mm DIP 16 0.92 x 0.55 x 0.40 inches 23.37 x 13.97 x 10.16 mm > 500 000hrs (MIL-HDBK-217 F at +25 oC) o 1.5mm from case for 10sec. 260 C 1.Reversed polarity at the input power will damage the driver. The input ground must not be connected to the negative output. 2.Leave the pin VADJ opened if not used , grounding VADJ will shut the driver off, connecting VADJ to +Vin will damage the driver. 3.Maximum output open voltage is equal to input voltage Safety Specifications Parameters Agency approvals Standards CE EN 55015 (CISPR22) IEC 61000-4-2 (Perf. Criteria A) IEC 61000-4-3 (Perf. Criteria A) IEC 61000-4-4 (Perf. Criteria A) IEC 61000-4-6 (Perf. Criteria A) IEC 61000-4-8 (Perf. Criteria A) www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 2 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Pin Out Specifications DIP 14 Pin 1 2 7 8 14 Single - V Input Vadj - V Output + V Output + V Input - DC Supply PWM/ON/OFF or not used LED Cathode connection LED Anode connection + DC Supply DIP 16 Pin 1 2 3 7 8 9 10 15 16 Single - V Input - V Input Vadj - V Output - V Output + V Output + V Output + V Input + V Input - DC Supply - DC Supply PWM/ON/OFF or not used LED Cathode connection LED Cathode connection LED Anode connection LED Anode connection + DC Supply + DC Supply Derating Free Air Convection 100 Output Power (%) 80 60 AMLDL-3030Z AMLDL-3035Z AMLDL-3050Z AMLDL-3060Z AMLDL-3070Z Safe Operating Area 40 AMLDL-301000Z 20 0 - 40 - 20 0 20 40 60 71 80 85 100 Ambient Temperature C www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 3 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Dimensions DIP 14: AMLDL-3030Z & AMLDL3035Z 20.32 (0.80) 15.24 (0.60) DIP 16: AMLDL-3050Z, AMLDL-3060Z, AMLDL3070Z, AMLDL-30100Z 23.40 (0.92) 17.78 (0.70) 2.54 (0.10) 123 78 10.16 (0.40) 1 2.54 (0.10) 12 2.81 (0.11) 10.16 (0.40) 5.08 (0.20) 7 8 14 0.50 (0.02) 1.92 (0.08) Bottom View 14.00 (0.55) Bottom View 16 15 0.50 (0.02) 10 9 Printed Face Printed Face 6.88 (0.27) 3.05 (0.12) 10.16 (0.40) 0.50 (0.02) Application circuit examples: +Vout + -Vin AMLDL-Z -Vout 1 1 3.05 (0.12) +Vout 1 LED -Vin st + AMLDL-Z -Vout 1 1st LED Last LED Analogue DIM PWM Dim/ON/OFF 1 1 Analogue DIM PWM Dim/ON/OFF Last LED AC In 5Vac to 21Vac 0.1uF optional 100uF to 330uF +Vin + -Vin AMLDL-Z +Vout 1 1st LED -Vout Last LED 1 AC In VADJ Analogue DIM PWM Dim/ON/OFF www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 4 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Output Current Adjustment by External DC Control Voltage: The nominal output current is given by: Iout 0.08 x Vadj X Model Number AMLDL-3030Z AMLDL-3035Z AMLDL-3050Z AMLDL-3060Z AMLDL-3070Z AMLDL-30100Z Vctrl R1 +5v +Vin 30K +Vout VADJ 0.3 -1.25V AMLDL-Z -Vin -Vout 1 1st LED X 0.327 0.280 0.197 0.165 0.1388 0.095 Last LED 1 GND +Vout VADJ R2 10K 1st LED 1 10K 10K AMLDL-Z -Vin -Vout +Vout VADJ AMLDL-Z -Vin -Vout 1 1 1st LED 1 TL431 10K 1 VADJ = R2 R1 + R2 X Vctrl www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 5 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Resistive Dimming Control A simplified dimming control can be achieved using a variable resistor connected between VADJ and GND. Capacitor CADJ is optional, it is installed to limit AC mains interference and high frequency noise. The recommended value of CADJ is 0.22F. The output current is given by: (0.08 / X) x Radj Iout +Vout (Radj + 200K) X 0.327 0.280 0.197 0.165 0.1388 0.095 CADJ RADJ VADJ 1st LED 1 AMLDL-Z -Vin -Vout Model Number AMLDL-3030Z AMLDL-3035Z AMLDL-3050Z AMLDL-3060Z AMLDL-3070Z AMLDL-30100Z 1 Output Current Adjustment by PWM Control: Driving VADJ Directly A Pulse Width Modulated (PWM) signal with a duty cycle of DPWM can be applied directly to VADJ pin as shown below. The output current is given by: 0.1 x DPWM [for 0 +Vout PWM VADJ AMLDL-Z -Vin GND -Vout 1 1st LED Model Number AMLDL-3030Z AMLDL-3035Z AMLDL-3050Z AMLDL-3060Z AMLDL-3070Z AMLDL-30100Z X 0.327 0.280 0.197 0.165 0.1388 0.095 Last LED 1 Driving VADJ Via Open Collector Transistor The VADJ can also be driven via an open collector transistor as shown below. The diode and resistor serve to suppress any possible high amplitude negative voltage spikes to the VADJ input resulting from the collector to emitter capacitance of the transistor. Any negative voltage spikes will cause errors in output current and/or unstable driver operation. +Vout PWM VADJ 10K 1 1st LED AMLDL-Z -Vin 1 1 1.25V 0V -Vout Last LED GND www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 6 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Driving the VADJ from a Microcontroller The VADJ can be driven from an open drain output of a microcontroller as shown below. The diode and resistor serve to suppress any possible high amplitude negative voltage spikes to the VADJ input resulting from the drain to source capacitance of the FET. Any negative voltage spikes will cause errors in output current and/or unstable driver operation. +Vout MCU VADJ 10K 1 1st LED AMLDL-Z -Vin 1 1 -Vout Last LED GND Output Current Adjustment by PWM Control (Dimming): A PWM signal must have a frequency of greater than 100Hz to prevent any visible flicker. +Vin 10uF 35V -Vin + AMSR-7805-Z + 100nF - + 10uF - 16V 470 7 8 Vcc Discharge 4 Reset + 100nF - 1N4148 1 1 6 VR 100K 2 + 100nF Threshold Out 3 210 Trigger GND NE 555 1 + 100nF CRT_V 5 2SD11782K 1 10K PMW AMLDL-Z Pin 2 (VADJ) 1N4148 AMLDL-Z Pin 1 Output Current Adjustment by PWM Control (Flash): +Vin 10uF 35V -Vin + AMSR-7805-Z + 100nF - + 10uF - 16V VR 100K 7 8 Vcc Discharge 4 Reset + 100nF - 6 2K Threshold Out 3 210 2 + 10uF - 16V NE 555 Trigger GND 1 + 100nF CRT_V 5 2SD11782K 1 10K PMW AMLDL-Z Pin 2 (VADJ) 1N4148 AMLDL-Z Pin 1 www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 7 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Recommended Class B EMI Filter: Model Number AMLDL-3030Z AMLDL-3035Z AMLDL-3050Z AMLDL-3060Z AMLDL-3070Z AMLDL-30100Z Inductor Value (H) 68 68 27 27 27 27 +Vin + 10uF -Vin L + AMLDL-Z - +Vout 1 1st LED -Vout 1 Last LED VADJ Analogue DIM PWM Dim/ON/OFF Thermal Feedback Circuit +Vin R1 4.7K BZX284C6V2 1 R2 10K Q1 1 VADJ 10K +Vin AMLDL-Z -Vin +Vout 1st LED 1 R3 10K Thermistor B 3900 -Vout Last LED 1 GND Thermally Connected The selection of components for the thermal feedback circuit is depends on the choice of R2 and R3 and the effectiveness of the LED heatsink. To optimize the LED brightness control at high temperatures, the LEDs must have a sufficient thermal extraction path, if not the reduction in drive current will not be optimal. The thermal control threshold points are set by adjusting R2. Three values (33K, 22K, and 10K) were tested. These values were chosen to provide thermal break points of approximately 25C, 40C, and 60C. Note, that the LED drive current will not continually dim to zero - the thermal controls applying DC control to that VADJ pin has a dimming ratio from maximum current of approximately 5:1. Once the reduced DC level drops below the shutdown threshold of around 200mV, the LED drive current will fall to zero and the LEDs will be off. The slope of the current reduction is determined by the beta value of the thermistor. The larger the Beta value the sharper will be the resultant current control response. The slope of the current reduction is also affected by Q1's base emitter voltage variation with temperature. www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 8 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Output Current Adjustment By External DC Control Voltage: +Vout 1N4148 1 6.2K VADJ 1.25V 1st LED AMLDL-Z -Vin 1 1 -Vout Last LED 10K GND +Vout 1N4148 1 6.2K VADJ 1.25V 1st LED AMLDL-Z -Vin 1 1 -Vout Last LED 10K GND +Vout 1N4148 +5V ~ +Vin 1 6.2K VADJ 1.25V 1st LED AMLDL-Z -Vin 1 1 -Vout Last LED 10K 4.7K GND +Vout 1N4148 1 TL431 OUT: 0 ~ 2.5V 1 6.2K VADJ 1.25V 1st LED AMLDL-Z -Vin 1 1 10K 10K -Vout Last LED GND GND +Vout 1N4148 1 6.2K VADJ 1.25V 1st LED AMLDL-Z -Vin 1 1 -Vout Last LED 10K GND +Vout 1N4148 1 6.2K VADJ 1.25V 1st LED AMLDL-Z -Vin 1 1 -Vout Last LED 10K GND www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 9 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Typical Characteristics: AMLDL-3030Z Frequency (KHz) 400 375 350 325 300 275 250 225 200 175 150 125 100 75 50 25 Operating Frequency vs Input Voltage (Forward Voltage = 3.5V per LED) Efficiency (%) 100 Efficiency vs Vin ( Forward Voltage = 3.5V per LED) 95 6 LED 4 LED 5 LED 7 LED 90 3 LED 85 2 LED 80 1 LED 3 LED 2 LED 4 LED 5 LED 6 LED 7 LED 75 1 LED 70 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Vin (V) Output Current Vs VADJ ILED (mA) 325 300 275 250 225 200 175 150 125 100 75 50 25 0 0 0.25 0.35 0.45 0.55 0.65 0.75 0.85 0.95 1.05 1.15 1.25 1.3 1.35 VADJ (V) www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 10 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Typical Characteristics: AMLDL-3035Z Frequency (KHz) 375 350 325 300 275 250 225 200 175 150 125 100 1 LED Operating Frequency vs Input Voltage (Forward Voltage = 3.5V per LED) Efficiency (%) 95.00 Efficiency vs Vin (Forward Voltage = 3.5V per LED) 7 LED 5 LED 4 LED 6 LED 90.00 2 LED 3 LED 85.00 80.00 75 50 25 1 LED 3 LED 2 LED 4 LED 5 LED 6 LED 7 LED 75.00 1 LED 70.00 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Vin (V) ILED (mA) 375 350 325 300 275 250 225 200 175 150 125 100 75 50 25 0 0 0.25 0.35 0.45 Output Current Vs VADJ 0.55 0.65 0.75 0.85 0.95 1.05 1.15 1.25 1.3 1.35 VADJ (V) www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 11 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Typical Characteristics: AMLDL-3050Z Operating Frequency vs Input Voltage (Forward Voltage = 3.5V per LED) Efficiency (%) 100.00% 95.00% 90.00% 1LED 2 LED Frequency (KHz) 350 325 300 275 250 225 200 175 150 1 LED Efficiency vs Vin (Forward Voltage = 3.5V per LED) 4 LED 5 LED 6 LED 7 LED 3 LED 85.00% 80.00% 1 LED 3 LED 2 LED 4 LED 5 LED 6 LED 7 LED 125 100 75 50 25 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 75.00% 70.00% 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Vin (V) ILED (mA) 600 Output Current Vs VADJ 500 400 300 200 100 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 VADJ (V) www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 12 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Typical Characteristics: AMLDL-3060Z Frequency (KHz) 325 300 275 250 225 200 175 150 125 100 75 50 25 0 1 LED Operating Frequency vs Input Voltage (Forward Voltage = 3.5V per LED) Efficiency (%) 100% Efficiency vs Vin (Forward Voltage = 3.5V per LED) 4 LED 5 LED 6 LED 7 LED 95% 3 LED 2 LED 90% 1 LED 85% 80% 3 LED 4 LED 5 LED 6 LED 7 LED 2 LED 75% 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 70% 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Vin (V) ILED (mA) Output Current Vs VADJ 700 600 500 400 300 200 100 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 VADJ (V) www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 13 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Typical Characteristics: AMLDL-3070Z Operating Frequency vs Input Frequency (KHz) (Forward Voltage = 3.5V per LED)) Efficiency (%) 100% 95% 90% 1 LED Efficiency vs Vin (Forward Voltage = 3.5V per LED) 4 LED 5 LED 6 LED 7 LED 350 325 300 275 250 225 200 175 150 125 100 75 50 25 Vin (V) 1 LED 2 LED 3 LED 4 LED 5 LED 6 LED 7 LED 3 LED 2 LED 85% 80% 75% 70% 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Output Current Vs VADJ ILED (mA) 700 600 500 400 300 200 100 0 0.05 0.15 0.25 0.35 0.45 0.55 0.65 0.75 0.85 0.95 1.05 1.15 1.25 VADJ (V) www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 14 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMLDL-Z Up to 1000mA | LED Driver Typical Characteristics: AMLD-30100Z Frequency (KHz) 300 275 250 225 200 175 150 125 100 75 50 25 7 Operating Frequency vs Input Voltage (Forward Voltage = 3.5V per LED) Efficiency (%) 100% Efficiency vs Vin (Forward Voltage = 3.5V per LED) 95% 3 LED 2 LED 4 LED 5 LED 6 LED 7 LED 90% 85% 1 LED 1 LED 80% 75% 3 LED 2 LED 8 5 LED 4 LED 6 LED 7 LED 70% 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Vin (V) Vin (V) ILED (mA) 1100 1000 900 800 700 600 500 400 300 200 100 0 0 Output Current Vs VADJ 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 VADJ (V) NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified.5..Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 5. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. www.aimtec.com F 051e R9.E Tel: +1 514 620 2722 15 of 15 Toll free: + 1 888 9 AIMTEC (924 6832) North America only |
Price & Availability of AMLDL-3030Z
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |