 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ELECTRONICS INC. 10Base-T Interface Module with Enhanced CMA and Resistor Network EPA2116G * Optimized for AMD/PHY controllers * * Robust construction allows for IR/VP processes * * Complies with or exceeds IEEE 802.3, 10Base-T Requirements * Electrical Parameters @ 25 C Cut-off Frequency (MHz) 1.0 MHz Xmit 17 Rcv 17 Insertion Loss (dB Max.) 1-10 MHz Xmit -1.5 Rcv -1 * Return Loss (dB Min.) 5-10 MHz Xmit -15 Rcv -15 @ 20 MHz Xmit -7 Rcv -5 Attenuation (dB Min.) (1) Common Mode Rejection (dB Min.) Crosstalk (dB Min.) [Between Channels] @ 1-10 MHz Rcv -30 -35 @ 25 MHz Xmit -18 Rcv -11 @ 30 MHz Xmit -30 Rcv -16 @ 40 MHz Xmit -33 Rcv -26 Xmit -30 @ 1-100 MHz Isolation : meets or exceeds 802.3 IEEE Requirements * Characteristic Filter Impedance : 100 * * Note: 1) Referenced to the filter output @ 5 MHz for filter only, excluding resistor network. * Transmit Channel 1 2 61.9 422 1.2K Schematic 14 8 49.9 15 Receive Channel 11 LPF 1:1 9 10 Media Side LPF 1:1 6 7 3 61.9 4 422 5 Chip Side 49.9 16 12 Chip Side Media Side Package A Dim. Min. .880 .360 .430 .700 .010 .100 .490 .017 .008 .095 0 .025 Dimensions (Inches) Max. Nom. .900 .380 .450 Typ. .015 Typ. .510 .022 .012 Typ. 5 .045 .040 .100 .100 .540 (Millimeters) Min. Max. Nom. 22.35 9.14 10.92 17.78 .254 2.54 12.45 .432 .203 2.41 0 .635 22.86 9.65 11.43 Typ. .381 Typ. 12.95 .559 .305 Typ. 5 1.14 1.02 2.54 2.54 13.72 J Pin 1 I.D. PCA EPA2116G Date Code N B Q Pad Layout P D M C E K L I A B C D E F G H I J K L M N P Q H F G PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 CSA2116Ga Rev. A 2/18/98 Product performance is limited to specified parameters. Data is subject to change without prior notice. TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pca.com ELECTRONICS INC. 10Base-T Module with Enhanced Common Mode Attenuation EPA2116G The circuit below is a guideline for interconnecting PCA's EPA2116G with AMD 79C96X and -970, PCnet chip family as reference controllers. Further details of system design, such as chip pin-out, etc. can be obtained from the specific chip manufacturer. Typical insertion loss of the isolation transformer/filter is 0.7dB. This parameter covers the entire spectrum of the encoded signals in 10 Base-T protocols. However, the predistortion resistor network introduces some loss which has to be taken into account in determining how well your design meets the Standard Template requirements. Users are encouraged to verify if this network best suits their application needs with the chip manufacturer before choosing a specific set of values. Additionally, user should make sure that these resistor values provide 802.3 Return Loss specification complaince at either extremes of the cable impedance, namely; 85 to 115. Implement only those parts in the design that will meet this requirement. A quick calculation of the effective Thevenin's termination impedance for the filter follows: R(termination)= 2(61.9//422)//1.2K100. Thus, when measuring the return loss of these parts on the bench, it is not necessary to provide a shunting resistor across the four outputs. The phantom resistors shown around the RJ45 connector have been known to suppress unwanted radiation that unused wires pick up from the immediate environment. Their placement and use are to be considered carefully before a design is finalized. It is recommended that there be a neat separation of ground planes in the layout. It is generally accepted practice to limit the plane off at least 0.08 inches away from the chip side pins of EPA2116G. There need not be any ground plane beyond this point. For best results, PCB designer should design the outgoing traces preferably to be 50, balanced and well coupled to achieve minimum radiation from these traces. Typical Application Circuit for UTP TX+ TXd+ TX+ TX- 1 2 3 4 14 16 8 6 11 9 1 2 3 6 10 Base-T PHY TXTXdRX+ RX- RJ45* RX+ RX4 5 7 8 EPA2116G 5 12 Chassis Ground Notes : * Pin-outs shown are for NIC configurations. For Hubs and Repeaters swap pins 1-2 with pins 3-6. PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 CSA2116Gb Rev. A 2/18/98 TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pca.com |
Price & Availability of EPA2116G
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |