Part Number Hot Search : 
RF3809 DTSPU50 AD974 FR20M05 K1536CT 2NBFA WM2637CD TA0706A
Product Description
Full Text Search
 

To Download CYV15G0104TRB Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 CYV15G0104TRB
Independent Clock HOTLink IITM Serializer and Reclocking Deserializer
Features
* Second-generation HOTLink(R) technology * Compliant to SMPTE 292M and SMPTE 259M video standards * Single channel video serializer plus single channel video reclocking deserializer -- 195- to 1500-Mbps serial data signaling rate -- Simultaneous operation at different signaling rates * Supports reception of either 1.485 or 1.485/1.001 Gbps data rate with the same training clock * Internal phase-locked loops (PLLs) with no external PLL components * Supports half-rate and full-rate clocking * Selectable differential PECL-compatible serial inputs -- Internal DC-restoration * Redundant differential PECL-compatible serial outputs -- No external bias resistors required -- Internal source termination * * * * -- Signaling-rate controlled edge-rates Synchronous LVTTL parallel interface JTAG boundary scan Built-In Self-Test (BIST) for at-speed link testing Link Quality Indicator -- Analog signal detect * * * * * -- Digital signal detect Low-power 1.8W @ 3.3V typical Single 3.3V supply Thermally enhanced BGA Pb-Free package option available 0.25 BiCMOS technology
Functional Description
The CYV15G0104TRB Independent Clock HOTLink IITM Serializer and Reclocking Deserializer is a point-to-point or point-to-multipoint communications building block enabling transfer of data over a variety of high-speed serial links including SMPTE 292M and SMPTE 259M video applications. It supports signaling rates in the range of 195 to 1500 Mbps per serial link. The transmit and receive channels are independent and can operate simultaneously at different rates. The transmit channel accepts 10-bit parallel characters in an Input Register and converts them to serial data. The receive channel accepts serial data and converts it to 10-bit parallel characters and presents these characters to an Output Register. The received serial data can also be reclocked and retransmitted through the reclocker serial outputs. Figure 1 illustrates typical connections between independent video co-processors and corresponding CYV15G0104TRB chips. The CYV15G0104TRB satisfies the SMPTE 259M and SMPTE 292M compliance as per SMPTE EG34-1999 Pathological Test Requirements. As a second-generation HOTLink device, the CYV15G0104TRB extends the HOTLink family with enhanced levels of integration and faster data rates, while maintaining serial-link compatibility (data and BIST) with other HOTLink devices. The transmit (TX) channel of the CYV15G0104TRB HOTLink II device accepts scrambled 10-bit transmission characters. These characters are serialized and output from dual Positive ECL (PECL) compatible differential transmission-line drivers at a bit-rate of either 10- or 20-times the input reference clock for that channel. The receive (RX) channel of the CYV15G0104TRB HOTLink II device accepts a serial bit-stream from one of two selectable PECL-compatible differential line receivers, and using a completely integrated Clock and Data Recovery PLL, recovers the timing information necessary for data reconstruction. The recovered bit-stream is reclocked and retransmitted through the reclocker serial outputs. Also, the recovered serial data is deserialized and presented to the destination host system. Figure 1. HOTLink IITM System Connections
Reclocked Output 10
10 Independent Channel CYV15G0104TRB Device 10 Reclocked Output Serial Links
Independent Channel CYV15G0104TRB Device 10
Cypress Semiconductor Corporation Document #: 38-02100 Rev. *C
*
198 Champion Court
*
San Jose, CA 95134-1709
* 408-943-2600 Revised May 2, 2007
[+] Feedback
Video Coprocessor
Video Coprocessor
CYV15G0104TRB
The transmit and receive channels contain an independent BIST pattern generator and checker, respectively. This BIST hardware allows at-speed testing of the high-speed serial data paths in each transmit and receive section, and across the interconnecting links.
The CYV15G0104TRB is ideal for SMPTE applications where different data rates and serial interface standards are necessary for each channel. Some applications include multi-format routers, switchers, format converters, SDI monitors, cameras, and camera control units.
CYV15G0104TRB Serializer and Reclocking Deserializer Logic Block Diagram
RXDA[9:0]
TRGCLKA
x10
x10
Phase Align Buffer Serializer
Deserializer
Reclocker
RX
TX
ROUTA1 ROUTA2
Document #: 38-02100 Rev. *C
TOUTB1 TOUTB2
INA1 INA2
TXDB[9:0]
REFCLKB
Page 2 of 28
[+] Feedback
CYV15G0104TRB
Reclocking Deserializer Path Block Diagram
TRGRATEA TRGCLKA SDASEL[2..1]A[1:0] LDTDEN
RESET TRST
x2
JTAG Boundary Scan Controller
TMS TCLK TDI TDO
BIST LFSR
Output Register
INSELA INA1+ INA1- INA2+ INA2- ULCA SPDSELA RXPLLPDA
Shifter
Receive Signal Monitor Clock & Data Recovery PLL
LFIA
10
10
10
RXDA[9:0]
BISTSTA
/2
RXBISTA[1:0] RXRATEA
RXCLKA+ RXCLKA-
Recovered Character Clock
Recovered Serial Data ROE[2..1]A
Reclocker Output PLL Clock Multiplier
RECLKOA REPDOA Character-Rate Clock
Register
ROE[2..1]A
ROUTA1+ ROUTA1- ROUTA2+ ROUTA2-
Bit-Rate Clock Bit-Rate Clock
Serializer Path Block Diagram
REFCLKB+ REFCLKB- TXRATEB SPDSELB TXCLKOB TXERRB TXCLKB TXCKSELB 0 1 Character-Rate Clock PABRSTB
= Internal Signal
TransmitPLL PLL Transmit Clock Multiplier Clock Multiplier
TOE[2..1]B
TXBISTB
TOE[2..1]B
Phase-Align Phase-Align Buffer Buffer
BIST LFSR
Input Register
TXDB[9:0]
10
10
10
10
Shifter
TOUTB1+ TOUTB1- TOUTB2+ TOUTB2-
Device Configuration and Control Block Diagram
RXRATEA RXPLLPDA TRGRATEA TXRATEB TXCKSELB PABRSTB SDASEL[2..1]A[1:0] TOE[2..1]B ROE[2..1]A RXBISTA[1:0] TXBISTB
= Internal Signal
WREN ADDR[2:0] DATA[6:0]
Device Configuration and Control Interface
Document #: 38-02100 Rev. *C
Page 3 of 28
[+] Feedback
CYV15G0104TRB
Pin Configuration (Top View)[1]
1 A B C D E F G H J K L M N P R T U V W Y
NC
2
NC
3
NC
4
NC
5
VCC VCC VCC VCC
6
NC
7
TOUT B1- TOUT B1+
8
GND
9
GND
10
TOUT B2- TOUT B2+ DATA [4] DATA [3]
11
IN A1- IN A1+ DATA [2] DATA [1]
12
ROUT A1- ROUT A1+ DATA [0]
13
GND
14
IN A2- IN A2+
15
ROUT A2- ROUT A2+ SPD SELB
16
VCC VCC VCC VCC
17
VCC NC
18
NC
19
VCC NC
20
NC
VCC
TDI
NC
VCC VCC VCC VCC
NC
VCC NC
GND
NC
GND
NC
NC
TMS
VCC
INSELA
NC
GND
DATA [6] DATA [5]
GND
NC
LDTD EN
TRST
GND
TDO
TCLK
RESET
ULCA
NC
GND
GND
GND
GND
NC
NC
VCC VCC
SCAN TMEN3 EN2
VCC
VCC
VCC
VCC
VCC
VCC
NC
NC
VCC
NC
VCC
NC
NC
NC
GND
WREN
GND
GND
NC
NC
SPD SELA
NC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
NC
NC
NC
NC
NC
NC
GND
GND
NC
NC
NC
NC
NC
NC
NC
GND
NC
NC
NC
GND
NC
NC
NC
NC
NC
NC
NC
GND
GND
GND
GND
GND
GND
GND
GND
GND
NC
NC
NC
NC
GND
GND
GND
GND
NC
NC
NC
NC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
TX DB[0] TX DB[3] TX DB[5] TX DB[6]
TX DB[1] TX DB[4] TX DB[7] TX CLKB
TX DB[2] TX DB[8]
TX DB[9]
VCC VCC VCC VCC
NC
NC
GND
GND
ADDR [0]
REF CLKB-
GND
GND
GND
VCC VCC VCC VCC
VCC VCC VCC VCC
RX DA[4] RX DA[9] LFIA
VCC
RX DA[5] TRG CLKA+ TRG CLKA-
BIST STA RX DA[2] RX DA[6] RX DA[8]
RX DA[0] RX DA[1] RX DA[3] RX DA[7]
NC
NC
NC
GND
NC
GND
REF RE CLKB+ CLKOA
GND
GND
NC
NC
NC
NC
GND
ADDR [2] TX CLKOB
ADDR [1]
RX REPDO GND CLKA+ A
GND
NC
NC
NC
NC
GND
NC
GND
RX CLKA-
GND
GND
TX ERRB
Note 1. NC = Do not connect.
Document #: 38-02100 Rev. *C
Page 4 of 28
[+] Feedback
CYV15G0104TRB
Pin Configuration (Bottom View)[1]
20 A B C D E F G H J K L M N P R T U V W Y
NC
19
VCC NC
18
NC
17
VCC NC
16
VCC VCC VCC VCC
15
ROUT A2- ROUT A2+ SPD SELB
14
IN A2- IN A2+
13
GND
12
ROUT A1- ROUT A1+ DATA [0]
11
IN A1- IN A1+ DATA [2] DATA [1]
10
TOUT B2- TOUT B2+ DATA [4] DATA [3]
9
GND
8
GND
7
TOUT B1- TOUT B1+
6
NC
5
VCC VCC VCC VCC
4
NC
3
NC
2
NC
1
NC
NC
NC
GND
NC
GND
VCC NC
NC
VCC VCC VCC VCC
NC
VCC
TDI
TDO
GND
TRST
LDTD EN
NC
GND
DATA [6] DATA [5]
GND
NC
VCC
INSELA
TMS
TMEN3 SCAN EN2
VCC VCC
NC
NC
GND
GND
GND
GND
NC
ULCA
RESET
TCLK
VCC
VCC
VCC
VCC
VCC
VCC
NC
NC
NC
VCC
NC
VCC
NC
NC
NC
SPD SELA
NC
NC
GND
GND
WREN
GND
GND
GND
GND
GND
GND
GND
GND
GND
NC
NC
NC
NC
GND
GND
GND
GND
NC
NC
NC
NC
GND
GND
NC
NC
GND
NC
NC
NC
GND
NC
NC
NC
GND
NC
NC
NC
NC
NC
NC
NC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
NC
NC
NC
NC
VCC
VCC
VCC
VCC
NC
NC
NC
NC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
VCC
RX DA[0] RX DA[1] RX DA[3] RX DA[7]
BIST STA RX DA[2] RX DA[6] RX DA[8]
VCC
RX DA[5] TRG CLKA+ TRG CLKA-
RX DA[4] RX DA[9] LFIA
VCC VCC VCC VCC
VCC VCC VCC VCC
GND
GND
GND
REF CLKB-
ADDR [0]
GND
GND
NC
NC
VCC VCC VCC VCC
TX DB[9]
TX DB[2] TX DB[8]
TX DB[1] TX DB[4] TX DB[7] TX CLKB
TX DB[0] TX DB[3] TX DB[5] TX DB[6]
GND
GND
RE REF CLKOA CLKB+ RX CLKA+
GND
NC
GND
NC
NC
NC
GND
GND REPDO
A
ADDR [1]
ADDR [2] TX CLKOB
GND
NC
NC
NC
NC
TX ERRB
GND
GND
RX CLKA-
GND
NC
GND
NC
NC
NC
NC
Document #: 38-02100 Rev. *C
Page 5 of 28
[+] Feedback
CYV15G0104TRB
Pin Definitions CYV15G0104TRB HOTLink II Serializer and Reclocking Deserializer
Name TXDB[9:0] I/O Characteristics LVTTL Input, synchronous, sampled by TXCLKB or REFCLKB[2] LVTTL Output, synchronous to REFCLKB [3], asynchronous to transmit channel enable / disable, asynchronous to loss or return of REFCLKB Signal Description Transmit Data Inputs. TXDB[9:0] data inputs are captured on the rising edge of the transmit interface clock. The transmit interface clock is selected by the TXCKSELB latch via the device configuration interface. Transmit Path Data and Status Signals
TXERRB
Transmit Path Error. TXERRB is asserted HIGH to indicate detection of a transmit Phase-Align Buffer underflow or overflow. If an underflow or overflow condition is detected, TXERRB, is asserted HIGH and remains asserted until the transmit Phase-Align Buffer is re-centered with the PABRSTB latch via the device configuration interface. When TXBISTB = 0, the BIST progress is presented on the TXERRB output. The TXERRB signal pulses HIGH for one transmit-character clock period to indicate a pass through the BIST sequence once every 511 character times. TXERRB is also asserted HIGH, when any of the following conditions is true: * The TXPLL is powered down. This occurs when TOE2B and TOE1B are both disabled by setting TOE2B = 0 and TOE1B = 0. * The absence of the REFCLKB signal. Reference Clock. REFCLKB clock inputs are used as the timing reference for the transmit PLL. This input clock may also be selected to clock the transmit parallel interface. When driven by a single-ended LVCMOS or LVTTL clock source, connect the clock source to either the true or complement REFCLKB input, and leave the alternate REFCLKB input open (floating). When driven by an LVPECL clock source, the clock must be a differential clock, using both inputs. Transmit Path Input Clock. When configuration latch TXCKSELB = 0, the associated TXCLKB input is selected as the character-rate input clock for the TXDB[9:0] input. In this mode, the TXCLKB input must be frequency-coherent to its TXCLKOB output clock, but may be offset in phase by any amount. Once initialized, TXCLKB is allowed to drift in phase by as much as 180 degrees. If the input phase of TXCLKB drifts beyond the handling capacity of the Phase Align Buffer, TXERRB is asserted to indicate the loss of data, and remains asserted until the Phase Align Buffer is initialized. The phase of TXCLKB relative to REFCLKB is initialized when the configuration latch PABRSTB is written as 0. When TXERRB is deasserted, the Phase Align Buffer is initialized and input characters are correctly captured. Transmit Clock Output. TXCLKOB output clock is synthesized by the transmit PLL and operates synchronous to the internal transmit character clock. TXCLKOB operates at either the same frequency as REFCLKB (TXRATEB = 0), or at twice the frequency of REFCLKB (TXRATEB = 1). The transmit clock outputs have no fixed phase relationship to REFCLKB. Parallel Data Output. RXDA[9:0] parallel data outputs change relative to the receive interface clock. If RXCLKA is a full-rate clock, the RXCLKA clock outputs are complementary clocks operating at the character rate. The RXDA[9:0] outputs for the associated receive channels follow rising edge of RXCLKA+ or falling edge of RXCLKA-. If RXCLKA is a half-rate clock, the RXCLKA clock outputs are complementary clocks operating at half the character rate. The RXDA[9:0] outputs for the associated receive channels follow both the falling and rising edges of the associated RXCLKA clock outputs. When BIST is enabled on the receive channel, the BIST status is presented on the RXDA[1:0] and BISTSTA outputs. See Table 6 for each status reported by the BIST state machine. Also, while BIST is enabled, the RXDA[9:2] outputs should be ignored.
Transmit Path Clock Signals REFCLKB Differential LVPECL or single-ended LVTTL input clock
TXCLKB
LVTTL Clock Input, internal pull-down
TXCLKOB
LVTTL Output
Receive Path Data and Status Signals RXDA[9:0] LVTTL Output, synchronous to the RXCLKA output
Notes 2. When REFCLKB is configured for half-rate operation, these inputs are sampled relative to both the rising and falling edges of the associated REFCLKB. 3. When REFCLKB is configured for half-rate operation, this output is presented relative to both the rising and falling edges of the associated REFCLKB.
Document #: 38-02100 Rev. *C
Page 6 of 28
[+] Feedback
CYV15G0104TRB
Pin Definitions (continued) CYV15G0104TRB HOTLink II Serializer and Reclocking Deserializer
Name BISTSTA I/O Characteristics LVTTL Output, synchronous to the RXCLKA output Asynchronous to reclocker output channel enable/disable Differential LVPECL or single-ended LVTTL input clock Signal Description BIST Status Output. When RXBISTA[1:0] = 10, BISTSTA (along with RXDA[1:0]) displays the status of the BIST reception. See Table 6 for the BIST status reported for each combination of BISTSTA and RXDA[1:0]. When RXBISTA[1:0] 10, BISTSTA should be ignored. REPDOA Reclocker Powered Down Status Output. REPDOA is asserted HIGH, when the reclocker output logic is powered down. This occurs when ROE2A and ROE1A are both disabled by setting ROE2A = 0 and ROE1A = 0.
Receive Path Clock Signals TRGCLKA CDR PLL Training Clock. TRGCLKA clock inputs are used as the reference source for the frequency detector (Range Controller) of the receive PLL to reduce PLL acquisition time. In the presence of valid serial data, the recovered clock output of the receive CDR PLL (RXCLKA) has no frequency or phase relationship with TRGCLKA. When driven by a single-ended LVCMOS or LVTTL clock source, connect the clock source to either the true or complement TRGCLKA input, and leave the alternate TRGCLKA input open (floating). When driven by an LVPECL clock source, the clock must be a differential clock, using both inputs. RXCLKA LVTTL Output Clock Receive Clock Output. RXCLKA is the receive interface clock used to control timing of the RXDA[9:0] parallel outputs. These true and complement clocks are used to control timing of data output transfers. These clocks are output continuously at either the half-character rate (1/20th the serial bit-rate) or character rate (1/10th the serial bit-rate) of the data being received, as selected by RXRATEA. Reclocker Clock Output. RECLKOA output clock is synthesized by the reclocker output PLL and operates synchronous to the internal recovered character clock. RECLKOA operates at either the same frequency as RXCLKA (RXRATEA = 0), or at twice the frequency of RXCLKA (RXRATEA = 1).The reclocker clock outputs have no fixed phase relationship to RXCLKA. Asynchronous Device Reset. RESET initializes all state machines, counters, and configuration latches in the device to a known state. RESET must be asserted LOW for a minimum pulse width. When the reset is removed, all state machines, counters and configuration latches are at an initial state. As per the JTAG specifications the device RESET cannot reset the JTAG controller. Therefore, the JTAG controller has to be reset separately. Refer to "JTAG Support" on page 16 for the methods to reset the JTAG state machine. See Table 4 on page 14 for the initialize values of the device configuration latches. Level Detect Transition Density Enable. When LDTDEN is HIGH, the Signal Level Detector, Range Controller, and Transition Density Detector are all enabled to determine if the RXPLL tracks TRGCLKA or the selected input serial data stream. If the Signal Level Detector, Range Controller, or Transition Density Detector are out of their respective limits while LDTDEN is HIGH, the RXPLL locks to TRGCLKA until such a time they become valid. SDASEL[2..1]A[1:0] is used to configure the trip level of the Signal Level Detector. The Transition Density Detector limit is one transition in every 60 consecutive bits. When LDTDEN is LOW, only the Range Controller is used to determine if the RXPLL tracks TRGCLKA or the selected input serial data stream. it is recommended to set LDTDEN = HIGH.
RECLKOA
LVTTL Output
Device Control Signals RESET LVTTL Input, asynchronous, internal pull-up
LDTDEN
LVTTL Input, internal pull-up
Document #: 38-02100 Rev. *C
Page 7 of 28
[+] Feedback
CYV15G0104TRB
Pin Definitions (continued) CYV15G0104TRB HOTLink II Serializer and Reclocking Deserializer
Name ULCA I/O Characteristics LVTTL Input, internal pull-up Signal Description Use Local Clock. When ULCA is LOW, the RXPLL is forced to lock to TRGCLKA instead of the received serial data stream. While ULCA is LOW, the link fault indicator LFIA is LOW indicating a link fault. When ULCA is HIGH, the RXPLL performs Clock and Data Recovery functions on the input data streams. This function is used in applications in which a stable RXCLKA is needed. In cases when there is an absence of valid data transitions for a long period of time, or the high-gain differential serial inputs (INA) are left floating, there may be brief frequency excursions of the RXCLKA outputs from TRGCLKA. SPDSELA SPDSELB 3-Level Select[4] static control input Serial Rate Select. The SPDSELA and SPDSELB inputs specify the operating signaling-rate range of the receive and transmit PLL, respectively. LOW = 195 - 400 MBd MID = 400 - 800 MBd HIGH = 800 - 1500 MBd. INSELA LVTTL Input, asynchronous Receive Input Selector. The INSELA input determines which external serial bit stream is passed to the receiver's Clock and Data Recovery circuit. When INSELA is HIGH, the Primary Differential Serial Data Input, INA1, is selected for the receive channel. When INSELA is LOW, the Secondary Differential Serial Data Input, INA2, is selected for the receive channel. Link Fault Indication Output. LFIA is an output status indicator signal. LFIA is the logical OR of six internal conditions. LFIA is asserted LOW when any of the following conditions is true: * Received serial data rate outside expected range * Analog amplitude below expected levels * Transition density lower than expected * Receive channel disabled * ULCA is LOW * Absence of TRGCLKA. Control Write Enable. The WREN input writes the values of the DATA[6:0] bus into the latch specified by the address location on the ADDR[2:0] bus.[5] Control Addressing Bus. The ADDR[2:0] bus is the input address bus used to configure the device. The WREN input writes the values of the DATA[6:0] bus into the latch specified by the address location on the ADDR[2:0] bus.[5] Table 4 lists the configuration latches within the device, and the initialization value of the latches upon the assertion of RESET. Table 5 shows how the latches are mapped in the device. Control Data Bus. The DATA[6:0] bus is the input data bus used to configure the device. The WREN input writes the values of the DATA[6:0] bus into the latch specified by address location on the ADDR[2:0] bus.[5 ] Table 4 on page 14 lists the configuration latches within the device, and the initialization value of the latches upon the assertion of RESET. Table 5 on page 15 shows how the latches are mapped in the device. Receive Clock Rate Select. Signal Detect Amplitude Select.
LFIA
LVTTL Output, asynchronous
Device Configuration and Control Bus Signals WREN LVTTL input, asynchronous, internal pull-up LVTTL input asynchronous, internal pull-up
ADDR[2:0]
DATA[6:0]
LVTTL input asynchronous, internal pull-up
Internal Device Configuration Latches RXRATEA Internal Latch[6] SDASEL[2..1] Internal Latch[6] A[1:0]
Notes 4. 3-Level Select inputs are used for static configuration. These are ternary inputs that make use of logic levels of LOW, MID, and HIGH. The LOW level is usually implemented by direct connection to VSS (ground). The HIGH level is usually implemented by direct connection to VCC (power). The MID level is usually implemented by not connecting the input (left floating), which allows it to self bias to the proper level. 5. See "Device Configuration and Control Interface" on page 13 for detailed information on the operation of the Configuration Interface. 6. See "Device Configuration and Control Interface" on page 13 for detailed information on the internal latches.
Document #: 38-02100 Rev. *C
Page 8 of 28
[+] Feedback
CYV15G0104TRB
Pin Definitions (continued) CYV15G0104TRB HOTLink II Serializer and Reclocking Deserializer
Name TXCKSELB TXRATEB TRGRATEA RXPLLPDA TXBISTB TOE2B TOE1B ROE2A ROE1A PABRSTB SCANEN2 TMEN3 Analog I/O TOUTB1 CML Differential Output Transmitter Primary Differential Serial Data Output. The transmitter TOUTB1 PECL-compatible CML outputs (+3.3V referenced) are capable of driving terminated transmission lines or standard fiber-optic transmitter modules, and must be AC-coupled for PECL-compatible connections. Transmitter Secondary Differential Serial Data Output. The transmitter TOUTB2 PECL-compatible CML outputs (+3.3V referenced) are capable of driving terminated transmission lines or standard fiber-optic transmitter modules, and must be AC-coupled for PECL-compatible connections. Reclocker Primary Differential Serial Data Output. The reclocker ROUTA1 PECL-compatible CML outputs (+3.3V referenced) are capable of driving terminated transmission lines or standard fiber-optic transmitter modules, and must be AC-coupled for PECL-compatible connections. Reclocker Secondary Differential Serial Data Output. The reclocker ROUTA2 PECL-compatible CML outputs (+3.3V referenced) are capable of driving terminated transmission lines or standard fiber-optic transmitter modules, and must be AC-coupled for PECL-compatible connections. Primary Differential Serial Data Input. The INA1 input accepts the serial data stream for deserialization. The INA1 serial stream is passed to the receive CDR circuit to extract the data content when INSELA = HIGH. Secondary Differential Serial Data Input. The INA2 input accepts the serial data stream for deserialization. The INA2 serial stream is passed to the receiver CDR circuit to extract the data content when INSELA = LOW. Test Mode Select. Used to control access to the JTAG Test Modes. If maintained high for 5 TCLK cycles, the JTAG test controller is reset. JTAG Test Clock. I/O Characteristics Internal Latch Internal
[6]
Signal Description Transmit Clock Select. Transmit PLL Clock Rate Select. Reclocker Output PLL Clock Rate Select. Receive Channel Power Control. Receive Bist Disabled. Transmit Bist Disabled. Transmitter Differential Serial Output Driver 2 Enable. Transmitter Differential Serial Output Driver 1 Enable. Reclocker Differential Serial Output Driver 2 Enable. Reclocker Differential Serial Output Driver 1 Enable. Transmit Clock Phase Alignment Buffer Reset. Factory Test 2. SCANEN2 input is for factory testing only. This input may be left as a NO CONNECT, or GND only. Factory Test 3. TMEN3 input is for factory testing only. This input may be left as a NO CONNECT, or GND only.
Internal Latch[6] Latch[6]
[6]
Internal Latch Internal Latch Internal Latch Internal
RXBISTA[1:0] Internal Latch[6]
[6] [6]
Internal Latch[6] Latch[6]
[6]
Internal Latch[6] Internal Latch
Factory Test Modes LVTTL input, internal pull-down LVTTL input, internal pull-down
TOUTB2
CML Differential Output
ROUTA1
CML Differential Output
ROUTA2
CML Differential Output
INA1
Differential Input
INA2
Differential Input
JTAG Interface TMS TCLK TDO LVTTL Input, internal pull-up LVTTL Input, internal pull-down
3-State LVTTL Output Test Data Out. JTAG data output buffer. High-Z while JTAG test mode is not selected.
Document #: 38-02100 Rev. *C
Page 9 of 28
[+] Feedback
CYV15G0104TRB
Pin Definitions (continued) CYV15G0104TRB HOTLink II Serializer and Reclocking Deserializer
Name TDI TRST Power VCC GND +3.3V Power. Signal and Power Ground for all internal circuits. configuration interface. When enabled, a register in the transmit channel becomes a signature pattern generator by logically converting to a Linear Feedback Shift Register (LFSR). This LFSR generates a 511-character sequence. This provides a predictable yet pseudo-random sequence that can be matched to an identical LFSR in the attached Receiver(s). A device reset (RESET sampled LOW) presets the BIST Enable Latches to disable BIST on all channels. All data present at the TXDB[9:0] inputs are ignored when BIST is active on that channel. Transmit PLL Clock Multiplier The Transmit PLL Clock Multiplier accepts a character-rate or half-character-rate external clock at the REFCLKB input, and that clock is multiplied by 10 or 20 (as selected by TXRATEB) to generate a bit-rate clock for use by the transmit shifter. It also provides a character-rate clock used by the transmit paths, and outputs this character rate clock as TXCLKOB. The clock multiplier PLL can accept a REFCLKB input between 19.5 MHz and 150 MHz, however, this clock range is limited by the operating mode of the CYV15G0104TRB clock multiplier (TXRATEB) and by the level on the SPDSELB input. SPDSELB is a 3-level select[4] input that selects one of three operating ranges for the serial data outputs of the transmit channel. The operating serial signaling-rate and allowable range of REFCLKB frequencies are listed in Table 1. Table 1. Operating Speed Settings SPDSELB LOW MID (Open) HIGH TXRATEB 1 0 1 0 1 0 REFCLKB Frequency (MHz) reserved 19.5-40 20-40 40-80 40-75 80-150 800-1500 400-800 Signaling Rate (Mbps) 195-400 I/O Characteristics LVTTL Input, internal pull-up LVTTL Input, internal pull-up Signal Description Test Data In. JTAG data input port. JTAG reset signal. When asserted (LOW), this input asynchronously resets the JTAG test access port controller.
CYV15G0104TRB HOTLink II Operation
The CYV15G0104TRB is a highly configurable, independent clocking device designed to support reliable transfer of large quantities of digital video data, using high-speed serial links from multiple sources to multiple destinations.
CYV15G0104TRB Transmit Data Path
Input Register The parallel input bus TXDB[9:0] can be clocked in using TXCLKB (TXCKSELB = 0) or REFCLKB (TXCKSELB = 1). Phase-Align Buffer Data from the Input Register is passed to the Phase-Align Buffer, when the TXDB[9:0] input register is clocked using TXCLKBA (TXCKSELB = 0) or when REFCLKB is a half-rate clock (TXCKSELB = 1 and TXRATEB = 1). When the TXDB[9:0] input register is clocked using REFCLKB (TXCKSELA = 1) and REFCLKB is a full-rate clock (TXRATEB = 0), the associated Phase Alignment Buffer in the transmit path is bypassed. These buffers are used to absorb clock phase differences between the TXCLKB input clock and the internal character clock for that channel. Once initialized, TXCLKB is allowed to drift in phase as much as 180 degrees. If the input phase of TXCLKB drifts beyond the handling capacity of the Phase Align Buffer, TXERRB is asserted to indicate the loss of data, and remains asserted until the Phase Align Buffer is initialized. The phase of TXCLKB relative to its internal character rate clock is initialized when the configuration latch PABRSTB is written as 0. When the associated TXERRB is deasserted, the Phase Align Buffer is initialized and input characters are correctly captured. If the phase offset, between the initialized location of the input clock and REFCLKB, exceeds the skew handling capabilities of the Phase-Align Buffer, an error is reported on that channel's TXERRB output. This output indicates an error continuously until the Phase-Align Buffer for that channel is reset. While the error remains active, the transmitter for that channel outputs a continuous "1001111000" character to indicate to the remote receiver that an error condition is present in the link. Transmit BIST The transmit channel contains an internal pattern generator that can be used to validate both the link and device operation. This generator is enabled by the TXBISTB latch via the device Document #: 38-02100 Rev. *C
The REFCLKB inputs are differential inputs with each input internally biased to 1.4V. If the REFCLKB+ input is connected to a TTL, LVTTL, or LVCMOS clock source, the input signal is recognized when it passes through the internally biased reference point. When driven by a single-ended TTL, LVTTL, or LVCMOS clock source, connect the clock source to either
Page 10 of 28
[+] Feedback
CYV15G0104TRB
the true or complement REFCLKB input, and leave the alternate REFCLKB input open (floating). When both the REFCLKB+ and REFCLKB- inputs are connected, the clock source must be a differential clock. This can either be a differential LVPECL clock that is DC- or AC-coupled or a differential LVTTL or LVCMOS clock. By connecting the REFCLKB- input to an external voltage source, it is possible to adjust the reference point of the REFCLKB+ input for alternate logic levels. When doing so, it is necessary to ensure that the input differential crossing point remains within the parametric range supported by the input. Transmit Serial Output Drivers The serial output interface drivers use differential Current Mode Logic (CML) drivers to provide source-matched drivers for 50 transmission lines. These drivers accept data from the transmit shifter. These drivers have signal swings equivalent to that of standard PECL drivers, and are capable of driving AC-coupled optical modules or transmission lines. Transmit Channels Enabled Each driver can be enabled or disabled separately via the device configuration interface. When a driver is disabled via the configuration interface, it is internally powered down to reduce device power. If both transmit serial drivers are in this disabled state, the transmitter internal logic for that channel is also powered down. A device reset (RESET sampled LOW) disables all output drivers. Note. When the disabled transmit channel (i.e., both outputs disabled) is re-enabled: * the data on the transmit serial outputs may not meet all timing specifications for up to 250 s * the state of the phase-align buffer cannot be guaranteed, and a phase-align reset is required if the phase-align buffer is used
Signal Detect/Link Fault Each selected Line Receiver (i.e., that routed to the clock and data recovery PLL) is simultaneously monitored for * analog amplitude above amplitude level selected by SDASELA * transition density above the specified limit * range controls report the received data stream inside normal frequency range (1500 ppm[24]) * receive channel enabled * Presence of reference clock * ULCA is not asserted. All of these conditions must be valid for the Signal Detect block to indicate a valid signal is present. This status is presented on the LFIA (Link Fault Indicator) output associated with each receive channel, which changes synchronous to the receive interface clock. Analog Amplitude While most signal monitors are based on fixed constants, the analog amplitude level detection is adjustable to allow operation with highly attenuated signals, or in high-noise environments. The analog amplitude level detection is set by the SDASELA latch via device configuration interface. The SDASELA latch sets the trip point for the detection of a valid signal at one of three levels, as listed in Table 2. This control input affects the analog monitors for all receive channels. The Analog Signal Detect monitors are active for the Line Receiver as selected by the INSELA input. Table 2. Analog Amplitude Detect Valid Signal Levels[7] SDASELA 00 01 10 11 Typical Signal with Peak Amplitudes Above Analog Signal Detector is disabled 140 mV p-p differential 280 mV p-p differential 420 mV p-p differential
CYV15G0104TRB Receive Data Path
Serial Line Receivers Two differential Line Receivers, INA1 and INA2, are available on the receive channel for accepting serial data streams. The active Serial Line Receiver is selected using the INSELA input. The Serial Line Receiver inputs are differential, and can accommodate wire interconnect and filtering losses or transmission line attenuation greater than 16 dB. For normal operation, these inputs should receive a signal of at least VIDIFF > 100 mV, or 200 mV peak-to-peak differential. Each Line Receiver can be DC- or AC-coupled to +3.3V powered fiber-optic interface modules (any ECL/PECL family, not limited to 100K PECL) or AC-coupled to +5V powered optical modules. The common-mode tolerance of these line receivers accommodates a wide range of signal termination voltages. Each receiver provides internal DC-restoration, to the center of the receiver's common mode range, for AC-coupled signals.
Transition Density The Transition Detection logic checks for the absence of transitions spanning greater than six transmission characters (60 bits). If no transitions are present in the data received, the Detection logic for that channel asserts LFIA. Range Controls The CDR circuit includes logic to monitor the frequency of the PLL Voltage Controlled Oscillator (VCO) used to sample the incoming data stream. This logic ensures that the VCO operates at, or near the rate of the incoming data stream for two primary cases: * when the incoming data stream resumes after a time in which it has been "missing." * when the incoming data stream is outside the acceptable signaling rate range.
Note 7. The peak amplitudes listed in this table are for typical waveforms that have generally 3-4 transitions for every ten bits. In a worse case environment the signals may have a sine-wave appearance (highest transition density with repeating 0101...). Signal peak amplitudes levels within this environment type could increase the values in the table above by approximately 100 mV.
Document #: 38-02100 Rev. *C
Page 11 of 28
[+] Feedback
CYV15G0104TRB
To perform this function, the frequency of the RXPLL VCO is periodically compared to the frequency of the TRGCLKA input. If the VCO is running at a frequency beyond 1500ppm[24] as defined by the TRGCLKA frequency, it is periodically forced to the correct frequency (as defined by TRGCLKA, SPDSELA, and TRGRATEA) and then released in an attempt to lock to the input data stream. The sampling and relock period of the Range Control is calculated as follows: RANGE_CONTROL_ SAMPLING_PERIOD = (RECOVERED BYTE CLOCK PERIOD) * (4096). During the time that the Range Control forces the RXPLL VCO to track TRGCLKA, the LFIA output is asserted LOW. After a valid serial data stream is applied, it may take up to one RANGE CONTROL SAMPLING PERIOD before the PLL locks to the input data stream, after which LFIA should be HIGH. The operating serial signaling-rate and allowable range of TRGCLKA frequencies are listed in Table 3. Table 3. Operating Speed Settings SPDSELA LOW MID (Open) HIGH TRGRATEA 1 0 1 0 1 0 Receive Channel Enabled The receive channel can be enabled or disabled through the RXPLLPDA input latch as controlled by the device configuration interface. When RXPLLPDA = 0, the CDR PLL and analog circuitry of the channel are disabled. Any disabled channel indicates a constant link fault condition on the LFIA output. When RXPLLPDA = 1, the CDR PLL and receive channel are enabled to receive a serial stream. Note. When the disabled receive channel is reenabled, the status of the LFIA output and data on the parallel outputs for the associated channel may be indeterminate for up to 2 ms. Clock/Data Recovery The extraction of a bit-rate clock and recovery of bits from the received serial stream is performed by a separate CDR block within the receive channel. The clock extraction function is performed by an integrated PLL that tracks the frequency of the transitions in the incoming bit stream and aligns the phase of the internal bit-rate clock to the transitions in the selected serial data stream. TRGCLKA Frequency (MHz) reserved 19.5-40 20-40 40-80 40-75 80-150 800-1500 400-800 Signaling Rate (Mbps) 195-400
Each CDR accepts a character-rate (bit-rate / 10) or half-character-rate (bit-rate / 20) training clock from the TRGCLKA input. This TRGCLKA input is used to * ensure that the VCO (within the CDR) is operating at the correct frequency (rather than a harmonic of the bit-rate) * reduce PLL acquisition time * limit unlocked frequency excursions of the CDR VCO when there is no input data present at the selected Serial Line Receiver. Regardless of the type of signal present, the CDR attempts to recover a data stream from it. If the signaling rate of the recovered data stream is outside the limits set by the range control monitors, the CDR tracks TRGCLKA instead of the data stream. Once the CDR output (RXCLKA) frequency returns back close to the TRGCLKA frequency, the CDR input is switched back to the input data stream. If no data is present at the selected line receiver, this switching behavior may result in brief RXCLKA frequency excursions from TRGCLKA. However, the validity of the input data stream is indicated by the LFIA output. The frequency of TRGCLKA is required to be within 1500ppm[24] of the frequency of the clock that drives the REFCLKB input of the remote transmitter to ensure a lock to the incoming data stream. This large ppm tolerance allows the CDR PLL to reliably receive a 1.485 or 1.485/1.001 Gbps SMPTE HD-SDI data stream with a constant TRGCLK frequency. For systems using multiple or redundant connections, the LFIA output can be used to select an alternate data stream. When an LFIA indication is detected, external logic can toggle selection of the INA1 and INA2 input through the INSELA input. When a port switch takes place, it is necessary for the receive PLL for that channel to reacquire the new serial stream. Reclocker The receive channel performs a reclocker function on the incoming serial data. To do this, the Clock and Data Recovery PLL first recovers the clock from the data. The data is retimed by the recovered clock and then passed to an output register. Also, the recovered character clock from the receive PLL is passed to the reclocker output PLL which generates the bit clock that is used to clock the retimed data into the output register. This data stream is then transmitted through the differential serial outputs. Reclocker Serial Output Drivers The serial output interface drivers use differential Current Mode Logic (CML) drivers to provide source-matched drivers for 50 transmission lines. These drivers accept data from the reclocker output register in the reclocker channel. These drivers have signal swings equivalent to that of standard PECL drivers, and are capable of driving AC-coupled optical modules or transmission lines. Reclocker Output Channels Enabled Each driver can be enabled or disabled separately via the device configuration interface. When a driver is disabled via the configuration interface, it is internally powered down to reduce device power. If both reclocker serial drivers are in this disabled state, the internal
Document #: 38-02100 Rev. *C
Page 12 of 28
[+] Feedback
CYV15G0104TRB
reclocker logic is also powered down. The deserialization logic and parallel outputs will remain enabled. A device reset (RESET sampled LOW) disables all output drivers. Note. When the disabled reclocker function (i.e., both outputs disabled) is re-enabled, the data on the reclocker serial outputs may not meet all timing specifications for up to 250 s. Output Bus The receive channel presents a 10-bit data signal (and a BIST status signal when RXBISTA[1:0] = 10). Receive BIST Operation The receiver channel contains an internal pattern checker that can be used to validate both device and link operation. These pattern checkers are enabled by the RXBISTA[1:0] latch via the device configuration interface. When enabled, a register in the receive channel becomes a signature pattern generator and checker by logically converting to a Linear Feedback Shift Register (LFSR). This LFSR generates a 511-character sequence. This provides a predictable yet pseudo-random sequence that can be matched to an identical LFSR in the attached Transmitter(s). When synchronized with the received data stream, the Receiver checks each character from the deserializer with each character generated by the LFSR and indicates compare errors and BIST status at the RXDA[1:0] and BISTSTA bits of the Output Register. The BIST status bus {BISTSTA, RXDA[0], RXDA[1]} indicates 010b or 100b for one character period per BIST loop to indicate loop completion. This status can be used to check test pattern progress. The specific status reported by the BIST state machine is listed in Table 6. These same codes are reported on the receive status outputs. If the number of invalid characters received ever exceeds the number of valid characters by 16, the receive BIST state machine aborts the compare operations and resets the LFSR to look for the start of the BIST sequence again. A device reset (RESET sampled LOW) presets the BIST Enable Latches to disable BIST on all channels. BIST Status State Machine When a receive path is enabled to look for and compare the received data stream with the BIST pattern, the {BISTSTA, RXDA[1:0]} bits identify the present state of the BIST compare operation. The BIST state machine has multiple states, as shown in Figure 2 and Table 6. When the receive PLL detects an out-of-lock condition, the BIST state is forced to the Start-of-BIST state, regardless of the present state of the BIST state machine. If the number of detected errors ever exceeds the number of valid matches by greater than 16, the state machine is forced to the WAIT_FOR_BIST state where it monitors the receive path for the first character of the next BIST sequence.
the device configuration interface. When RXPLLPDA = 0, the receive PLL and analog circuitry of the channel is disabled. The transmit channel is controlled by the TOE1B and the TOE2B latches via the device configuration interface. The reclocker function is controlled by the ROE1A and the ROE2A latches via the device configuration interface. When a driver is disabled via the configuration interface, it is internally powered down to reduce device power. If both serial drivers for a channel are in this disabled state, the associated internal logic for that channel is also powered down. When the reclocker serial drivers are disabled, the reclocker function will be disabled, but the deserialization logic and parallel outputs will remain enabled. Device Reset State When the CYV15G0104TRB is reset by assertion of RESET, all state machines, counters, and configuration latches in the device are initialized to a reset state. Additionally, the JTAG controller must also be reset for valid operation (even if JTAG testing is not performed). See "JTAG Support" on page 16 for JTAG state machine initialization. See Table 4 on page 14 for the initialize values of the configuration latches. Following a device reset, it is necessary to enable the transmit and receive channels used for normal operation. This can be done by sequencing the appropriate values on the device configuration interface.[5]
Device Configuration and Control Interface
The CYV15G0104TRB is highly configurable via the configuration interface. The configuration interface allows the transmitter and reclocker to be configured independently. Table 4 lists the configuration latches within the device including the initialization value of the latches upon the assertion of RESET. Table 5 on page 15 shows how the latches are mapped in the device. Each row in the Table 5 maps to a 7-bit latch bank. There are 6 such write-only latch banks. When WREN = 0, the logic value in the DATA[6:0] is latched to the latch bank specified by the values in ADDR[2:0]. The second column of Table 5 specifies the channels associated with the corresponding latch bank. For example, the first three latch banks (0,1 and 2) consist of configuration bits for the reclocker channel A. Latch Types There are two types of latch banks: static (S) and dynamic (D). Each channel is configured by 2 static and 1 dynamic latch banks. The S type contain those settings that normally do not change for a given application, whereas the D type controls the settings that could change during the application's lifetime. The first and second rows of each channel (address numbers 0, 1, 5, and 6) are the static control latches. The third row of latches for each channel (address numbers 2 and 7) are the dynamic control latches that are associated with enabling dynamic functions within the device. Address numbers 3 and 4 are internal test registers. Static Latch Values There are some latches in the table that have a static value (i.e. 1, 0, or X). The latches that have a `1' or `0' must be configured with their corresponding value each time that their
Power Control
The CYV15G0104TRB supports user control of the powered up or down state of each transmit and receive channel. The receive channels are controlled by the RXPLLPDA latch via Document #: 38-02100 Rev. *C
Page 13 of 28
[+] Feedback
CYV15G0104TRB
associated latch bank is configured. The latches that have an `X' are don't cares and can be configured with any value. Table 4. Device Configuration and Control Latch Descriptions Name RXRATEA Signal Description Receive Clock Rate Select. The initialization value of the RXRATEA latch = 1. RXRATEA is used to select the rate of the RXCLKA clock output. When RXRATEA = 1, the RXCLKA clock outputs are complementary clocks that follow the recovered clock operating at half the character rate. Data for the associated receive channels should be latched alternately on the rising edge of RXCLKA+ and RXCLKA-. When RXRATEA = 0, the RXCLKA clock outputs are complementary clocks that follow the recovered clock operating at the character rate. Data for the associated receive channels should be latched on the rising edge of RXCLKA+ or falling edge of RXCLKA-.
SDASEL1A[1:0] Primary Serial Data Input Signal Detector Amplitude Select. The initialization value of the SDASEL1A[1:0] latch = 10. SDASEL1A[1:0] selects the trip point for the detection of a valid signal for the INA1 Primary Differential Serial Data Inputs. When SDASEL1A[1:0] = 00, the Analog Signal Detector is disabled. When SDASEL1A[1:0] = 01, the typical p-p differential voltage threshold level is 140 mV. When SDASEL1A[1:0] = 10, the typical p-p differential voltage threshold level is 280 mV. When SDASEL1A[1:0] = 11, the typical p-p differential voltage threshold level is 420 mV. SDASEL2A[1:0] Secondary Serial Data Input Signal Detector Amplitude Select. The initialization value of the SDASEL2A[1:0] latch = 10. SDASEL2A[1:0] selects the trip point for the detection of a valid signal for the INA2 Secondary Differential Serial Data Inputs. When SDASEL2A[1:0] = 00, the Analog Signal Detector is disabled When SDASEL2A[1:0] = 01, the typical p-p differential voltage threshold level is 140 mV. When SDASEL2A[1:0] = 10, the typical p-p differential voltage threshold level is 280 mV. When SDASEL2A[1:0] = 11, the typical p-p differential voltage threshold level is 420 mV. TRGRATEA Training Clock Rate Select. The initialization value of the TRGRATEA latch = 0. TRGRATEA is used to select the clock multiplier for the training clock input to the CDR PLL. When TRGRATEA = 0, the TRGCLKA input is not multiplied before it is passed to the CDR PLL. When TRGRATEA = 1, the TRGCLKA input is multiplied by 2 before it is passed to the CDR PLL. TRGRATEA = 1 and SPDSELA = LOW is an invalid state and this combination is reserved. Receive Channel Enable. The initialization value of the RXPLLPDA latch = 0. RXPLLPDA selects if the receive channel is enabled or powered-down. When RXPLLPDA = 0, the receive PLL and analog circuitry are powered-down. When RXPLLPDA = 1, the receive PLL and analog circuitry are enabled. Receive Bist Disable / SMPTE Receive Enable. The initialization value of the RXBISTA[1:0] latch = 11. For SMPTE data reception, RXBISTA[1:0] should not remain in this initialization state (11). RXBISTA[1:0] selects if receive BIST is disabled or enabled and sets the device for SMPTE data reception. When RXBISTA[1:0] = 01, the receiver BIST function is disabled and the device is set to receive SMPTE data. When RXBISTA[1:0] = 10, the receive BIST function is enabled and the device is set to receive BIST data. RXBISTA[1:0] = 00 and RXBISTA[1:0] = 11 are invalid states. Reclocker Secondary Differential Serial Data Output Driver Enable. The initialization value of the ROE2A latch = 0. ROE2A selects if the ROUTA2 secondary differential output drivers are enabled or disabled. When ROE2A = 1, the associated serial data output driver is enabled allowing the reclocked data to be transmitted. When ROE2A = 0, the associated serial data output driver is disabled. When a driver is disabled via the configuration interface, it is internally powered down to reduce device power. If both serial drivers for a channel are in this disabled state, the reclocker logic is also powered down. A device reset (RESET sampled LOW) disables all output drivers. Reclocker Primary Differential Serial Data Output Driver Enable. The initialization value of the ROE1A latch = 0. ROE1A selects if the ROUTA1 primary differential output drivers are enabled or disabled. When ROE1A = 1, the associated serial data output driver is enabled allowing the reclocked data to be transmitted. When ROE1A = 0, the associated serial data output driver is disabled. When a driver is disabled via the configuration interface, it is internally powered down to reduce device power. If both serial drivers for a channel are in this disabled state, the reclocker logic is also powered down. A device reset (RESET sampled LOW) disables all output drivers. Transmit Clock Select. The initialization value of the TXCKSELB latch = 1. TXCKSELB selects the clock source used to write data into the Transmit Input Register. When TXCKSELB = 1, the input register TXDB[9:0] is clocked by REFCLKB. In this mode, the phase alignment buffer in the transmit path is bypassed. When TXCKSELB = 0, TXCLKB is used to clock in the input register TXDB[9:0].
RXPLLPDA
RXBISTA[1:0]
ROE2A
ROE1A
TXCKSELB
Document #: 38-02100 Rev. *C
Page 14 of 28
[+] Feedback
CYV15G0104TRB
Table 4. Device Configuration and Control Latch Descriptions (continued) Name TXRATEB Signal Description Transmit PLL Clock Rate Select. The initialization value of the TXRATEB latch = 0. TXRATEB is used to select the clock multiplier for the Transmit PLL. When TXRATEB = 0, the transmit PLL multiples the REFCLKB input by 10 to generate the serial bit-rate clock. When TXRATEB = 0, the TXCLKOB output clocks are full-rate clocks and follow the frequency and duty cycle of the REFCLKB input. When TXRATEB = 1, the Transmit PLL multiplies the REFCLKB input by 20 to generate the serial bit-rate clock. When TXRATEB = 1, the TXCLKOB output clocks are twice the frequency rate of the REFCLKB input. When TXCKSELB = 1 and TXRATEB = 1, the Transmit Data Inputs are captured using both the rising and falling edges of REFCLKB. TXRATEB = 1 and SPDSELB = LOW, is an invalid state and this combination is reserved. Transmit Bist Disable. The initialization value of the TXBISTB latch = 1. TXBISTB selects if the transmit BIST is disabled or enabled. When TXBISTB = 1, the transmit BIST function is disabled. When TXBISTB = 0, the transmit BIST function is enabled. Secondary Differential Serial Data Output Driver Enable. The initialization value of the TOE2B latch = 0. TOE2B selects if the TOUTB2 secondary differential output drivers are enabled or disabled. When TOE2B = 1, the associated serial data output driver is enabled allowing data to be transmitted from the transmit shifter. When TOE2B = 0, the associated serial data output driver is disabled. When a driver is disabled via the configuration interface, it is internally powered down to reduce device power. If both serial drivers for a channel are in this disabled state, the associated internal logic for that channel is also powered down. A device reset (RESET sampled LOW) disables all output drivers. Primary Differential Serial Data Output Driver Enable. The initialization value of the TOE1B latch = 0. TOE1B selects if the TOUTB1 primary differential output drivers are enabled or disabled. When TOE1B = 1, the associated serial data output driver is enabled allowing data to be transmitted from the transmit shifter. When TOE1B = 0, the associated serial data output driver is disabled. When a driver is disabled via the configuration interface, it is internally powered down to reduce device power. If both serial drivers for a channel are in this disabled state, the associated internal logic for that channel is also powered down. A device reset (RESET sampled LOW) disables all output drivers. Transmit Clock Phase Alignment Buffer Reset. The initialization value of the PABRSTB latch = 1. The PABRSTB is used to re-center the Transmit Phase Align Buffer. When the configuration latch PABRSTB is written as a 0, the phase of the TXCLKB input clock relative to REFCLKB+/- is initialized. PABRSTB is an asynchronous input, but is sampled by each TXCLKB to synchronize it to the internal clock domain. PABRSTB is a self clearing latch. This eliminates the requirement of writing a 1 to complete the initialization of the Phase Alignment Buffer.
TXBISTB
TOE2B
TOE1B
PABRSTB
Table 5. Device Control Latch Configuration Table
ADDR 0 (000b) 1 (001b) 2 (010b) 3 (011b) 4 (100b) 5 (101b) 6 (110b) 7 (111b) B B B S S D X X X X X 0 Channel A A A Type S S D DATA6 1 SDASEL2A[1] RXBISTA[1] DATA5 0 SDASEL2A[0] RXPLLPDA DATA4 X SDASEL1A[1] RXBISTA[0] DATA3 X SDASEL1A[0] X DATA2 0 X ROE2A DATA1 0 X ROE1A DATA0 RXRATEA TRGRATEA X Reset Value 1011111 1010110 1011001
INTERNAL TEST REGISTERS DO NOT WRITE TO THESE ADDRESSES
X X X
X X TXBISTB
X 0 TOE2B
0 TXCKSELB TOE1B
X TXRATEB PABRSTB
1011111 1010110 1011001
Document #: 38-02100 Rev. *C
Page 15 of 28
[+] Feedback
CYV15G0104TRB
Device Configuration Strategy The following is a series of ordered events needed to load the configuration latches on a per channel basis: 1. Pulse RESET Low after device power-up. This operation resets both channels. Initialize the JTAG state machine to its reset state as detailed in JTAG Support. 2. Set the static latch banks for the target channel. 3. Set the dynamic bank of latches for the target channel. Enable the Receive PLL and/or transmit channel. If the receiver is enabled, set the device for SMPTE data reception (RXBISTA[1:0] = 01) or BIST data reception (RXBISTA[1:0] = 10). 4. Reset the Phase Alignment Buffer. [Optional if phase align buffer is bypassed.]
high-speed serial inputs and outputs are not part of the JTAG test chain. To ensure valid device operation after power-up (including non-JTAG operation), the JTAG state machine should also be initialized to a reset state. This should be done in addition to the device reset (using RESET). The JTAG state machine can be initialized using TRST (asserting it LOW and deasserting it or leaving it asserted), or by asserting TMS HIGH for at least 5 consecutive TCLK cycles. This is necessary in order to ensure that the JTAG controller does not enter any of the test modes after device power-up. In this JTAG reset state, the rest of the device will be in normal operation. Note. The order of device reset (using RESET) and JTAG initialization does not matter. 3-Level Select Inputs Each 3-Level select inputs reports as two bits in the scan register. These bits report the LOW, MID, and HIGH state of the associated input as 00, 10, and 11 respectively JTAG ID The JTAG device ID for the CYV15G0104TRB is `0C811069'x.
JTAG Support
The CYV15G0104TRB contains a JTAG port to allow system level diagnosis of device interconnect. Of the available JTAG modes, boundary scan, and bypass are supported. This capability is present only on the LVTTL inputs and outputs, the TRGCLKA input, and the REFCLKB clock input. The Table 6. Receive BIST Status Bits
Description {BISTSTA, RXDA[0], RXDA[1]} 000, 001 010 011 100 101 110 111 Receive BIST Status (Receive BIST = Enabled) BIST Data Compare. Character compared correctly. BIST Last Good. Last Character of BIST sequence detected and valid. Reserved. BIST Last Bad. Last Character of BIST sequence detected invalid. BIST Start. Receive BIST is enabled on this channel, but character compares have not yet commenced. This also indicates a PLL Out of Lock condition. BIST Error. While comparing characters, a mismatch was found in one or more of the character bits. BIST Wait. The receiver is comparing characters but has not yet found the start of BIST character to enable the LFSR.
Document #: 38-02100 Rev. *C
Page 16 of 28
[+] Feedback
CYV15G0104TRB
Figure 2. Receive BIST State Machine
Monitor Data Received
Receive BIST {BISTSTA, RXDA[0], Detected LOW RXDA[1]} = BIST_START (101)
RX PLL Out of Lock
{BISTSTA, RXDA[0], RXDA[1]} = BIST_WAIT (111)
No
Start of BIST Detected
Yes, {BISTSTA, RXDA[0], RXDA[1]} = BIST_DATA_COMPARE (000, 001)
Compare Next Character Mismatch
Yes
Auto-Abort Condition
Match
{BISTSTA, RXDA[0], RXDA[1]} = BIST_DATA_COMPARE (000, 001)
No
End-of-BIST State
End-of-BIST State
No
Yes, {BISTSTA, RXDA[0], RXDA[1]} = BIST_LAST_BAD (100)
Yes, {BISTSTA, RXDA[0], RXDA[1]} = BIST_LAST_GOOD (010)
No, {BISTSTA, RXDA[0], RXDA[1]} = BIST_ERROR (110)
Document #: 38-02100 Rev. *C
Page 17 of 28
[+] Feedback
CYV15G0104TRB
Maximum Ratings
(Above which the useful life may be impaired. User guidelines only, not tested.) Storage Temperature .................................. -65C to +150C Ambient Temperature with Power Applied............................................. -55C to +125C Supply Voltage to Ground Potential ............... -0.5V to +3.8V DC Voltage Applied to LVTTL Outputs in High-Z State .......................................-0.5V to VCC + 0.5V Output Current into LVTTL Outputs (LOW)..................60 mA DC Input Voltage....................................-0.5V to VCC + 0.5V
Static Discharge Voltage.......................................... > 2000 V (per MIL-STD-883, Method 3015) Latch-up Current..................................................... > 200 mA Power-up Requirements The CYV15G0104TRB requires one power supply. The Voltage on any input or I/O pin cannot exceed the power pin during power-up.
Operating Range
Range Commercial Ambient Temperature 0C to +70C VCC +3.3V 5%
CYV15G0104TRB DC Electrical Characteristics
Parameter LVTTL-compatible Outputs VOHT VOLT IOST IOZL VIHT VILT IIHT IILT IIHPDT IILPUT VDIFF[9] VIHHP VILLP VCOMREF VIHH VIMM VILL IIHH IIMM IILL
[10]
Description Output HIGH Voltage Output LOW Voltage Output Short Circuit Current High-Z Output Leakage Current Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current Input HIGH Current with internal pull-down Input LOW Current with internal pull-up Input Differential Voltage Highest Input HIGH Voltage Lowest Input LOW voltage Common Mode Range Three-Level Input HIGH Voltage Three-Level Input MID Voltage Three-Level Input LOW Voltage Input HIGH Current Input MID current Input LOW current
Test Conditions IOH = - 4 mA, VCC = Min. IOL = 4 mA, VCC = Min. VOUT = 0V[8], VCC = 3.3V VOUT = 0V, VCC
Min. 2.4
Max.
Unit V
0.4 -20 -20 2.0 -0.5 -100 20 VCC + 0.3 0.8 1.5 +40 -1.5 -40 +200 -200 400 1.2 0.0 1.0 VCC VCC VCC/2 VCC - 1.2V VCC 0.53 * VCC 0.13 * VCC 200 -50 50 -200
V mA A V V mA A mA A A A mV V V V V V V A A A
LVTTL-compatible Inputs
REFCLKB Input, VIN = VCC Other Inputs, VIN = VCC REFCLKB Input, VIN = 0.0V Other Inputs, VIN = 0.0V VIN = VCC VIN = 0.0V
LVDIFF Inputs: REFCLKB
3-Level Inputs Min. VCC Max. Min. VCC Max. Min. VCC Max. VIN = VCC VIN = VCC/2 VIN = GND 0.87 * VCC 0.47 * VCC 0.0
Notes 8. Tested one output at a time, output shorted for less than one second, less than 10% duty cycle. 9. This is the minimum difference in voltage between the true and complement inputs required to ensure detection of a logic-1 or logic-0. A logic-1 exists when the true (+) input is more positive than the complement (-) input. A logic-0 exists when the complement (-) input is more positive than true (+) input. 10. The common mode range defines the allowable range of REFCLKB+ and REFCLKB- when REFCLKB+ = REFCLKB-. This marks the zero-crossing between the true and complement inputs as the signal switches between a logic-1 and a logic-0.
Document #: 38-02100 Rev. *C
Page 18 of 28
[+] Feedback
CYV15G0104TRB
CYV15G0104TRB DC Electrical Characteristics (continued)
Parameter VOHC VOLC VODIF Description Output HIGH Voltage (VCC Referenced) Output LOW Voltage (VCC Referenced) Output Differential Voltage |(OUT+) - (OUT-)| Input Differential Voltage |(IN+) - (IN-)| Highest Input HIGH Voltage Lowest Input LOW Voltage Input HIGH Current Input LOW Current
[11]
Test Conditions 100 differential load 150 differential load 100 differential load 150 differential load 100 differential load 150 differential load
Min. VCC - 0.5 VCC - 0.5 VCC - 1.4 VCC - 1.4 450 560 100 VCC - 2.0
Max. VCC - 0.2 VCC - 0.2 VCC - 0.7 VCC - 0.7 900 1000 1200 VCC
Unit V V V V mV mV mV V V A A V
Differential CML Serial Outputs: OUTA1, OUTA2, OUTB1, OUTB2, OUTC1, OUTC2, OUTD1, OUTD2
Differential Serial Line Receiver Inputs: INA1, INA2 VDIFFs[9] VIHE VILE IIHE IILE VICOM
VIN = VIHE Max. VIN = VILE Min. ((VCC - 2.0V)+0.5)min, (VCC - 0.5V) max. REFCLKB = MAX Commercial -700 +1.25 Typ. 585 560
1350 +3.1 Max. 690 660
Common Mode input range
Power Supply ICC [12, 13] ICC [12, 13] Max Power Supply Current Typical Power Supply Current
mA mA
REFCLKB Commercial = 125 MHz
AC Test Loads and Waveforms
3.3V R1 R1 = 590 R2 = 435 CL CL 7 pF (Includes fixture and probe capacitance) RL = 100 (Includes fixture and probe capacitance) RL
R2
[14]
(b) CML Output Test Load
[14]
(a) LVTTL Output Test Load
3.0V Vth = 1.4V GND 1 ns 2.0V 0.8V 2.0V 0.8V
VIHE Vth = 1.4V VILE 1 ns 20%
VIHE 80% VILE 80% 20% 270 ps
270 ps
(c) LVTTL Input Test Waveform
[15]
(d) CML/LVPECL Input Test Waveform
Note 11. The common mode range defines the allowable range of INPUT+ and INPUT- when INPUT+ = INPUT-. This marks the zero-crossing between the true and complement inputs as the signal switches between a logic-1 and a logic-0. 12. Maximum ICC is measured with VCC = MAX,TA = 25C, with all channels and Serial Line Drivers enabled, sending a continuous alternating 01 pattern, and outputs unloaded. 13. Typical ICC is measured under similar conditions except with VCC = 3.3V, TA = 25C,with all channels enabled and one Serial Line Driver per channel sending a continuous alternating 01 pattern. The redundant outputs on each channel are powered down and the parallel outputs are unloaded. 14. Cypress uses constant current (ATE) load configurations and forcing functions. This figure is for reference only. 15. The LVTTL switching threshold is 1.4V. All timing references are made relative to where the signal edges cross the threshold voltage.
Document #: 38-02100 Rev. *C
Page 19 of 28
[+] Feedback
CYV15G0104TRB
CYV15G0104TRB AC Electrical Characteristics
Parameter fTS tTXCLK tTXCLKH[16] tTXCLKL[16] tTXCLKR [16, 17, 18, 19] tTXCLKF [16, 17, 18, 19] tTXDS tTXDH fTOS tTXCLKO tTXCLKOD fRS tRXCLKP tRXCLKD tRXCLKR
[16]
Description TXCLKB Clock Cycle Frequency TXCLKB Period=1/fTS TXCLKB HIGH Time TXCLKB LOW Time TXCLKB Rise Time TXCLKB Fall Time Transmit Data Set-up Time to TXCLKB (TXCKSELB = 0) Transmit Data Hold Time from TXCLKB (TXCKSELB = 0) TXCLKOB Clock Frequency = 1x or 2x REFCLKB Frequency TXCLKOB Period=1/fTOS TXCLKOB Duty Cycle centered at 60% HIGH time RXCLKA Clock Output Frequency RXCLKA Period = 1/fRS RXCLKA Duty Cycle Centered at 50% (Full Rate and Half Rate) RXCLKA Rise Time RXCLKA Fall Time Status and Data Valid Time to RXCLKA (RXRATEA = 0) (Full Rate) Status and Data Valid Time to RXCLKA (RXRATEA = 1) (Half Rate) Status and Data Valid Time to RXCLKA (RXRATEA = 0) Status and Data Valid Time to RXCLKA (RXRATEA = 1) RECLKOA Clock Frequency RECLKOA Period=1/fROS RECLKOA Duty Cycle centered at 60% HIGH time REFCLKB Clock Frequency REFCLKB Period = 1/fREF REFCLKB HIGH Time (TXRATEB = 1)(Half Rate) REFCLKB HIGH Time (TXRATEB = 0)(Full Rate) REFCLKB LOW Time (TXRATEB = 1)(Half Rate) REFCLKB LOW Time (TXRATEB = 0)(Full Rate) REFCLKB Duty Cycle REFCLKB Rise Time (20%-80%) REFCLKB Fall Time (20%-80%)
Min. 19.5 6.66 2.2 2.2 0.2 0.2 2.2 1.0 19.5 6.66 -1.9 9.75 6.66 -1.0 0.3 0.3 5UI-2.0[21] 5UI-1.3[21] 5UI-1.8[21] 5UI-2.6 19.5 6.66 -1.9 19.5 6.6 5.9 2.9[16] 5.9 2.9[16] 30
[21]
Max 150 51.28
Unit MHz ns ns ns
CYV15G0104TRB Transmitter LVTTL Switching Characteristics Over the Operating Range
1.7 1.7
ns ns ns ns
150 51.28 0 150 102.56 +1.0 1.2 1.2
MHz ns ns MHz ns ns ns ns ns ns ns ns
CYV15G0104TRB Receiver LVTTL Switching Characteristics Over the Operating Range
tRXCLKF [16] tRXDv-[20] tRXDv+[20] fROS tRECLKO tRECLKOD fREF tREFCLK tREFH tREFL tREFD[22] tREFR [16, 17, 18, 19] tREFF[16, 17, 18, 19]
150 51.28 0 150 51.28
MHz ns ns MHz ns ns ns ns ns
CYV15G0104TRB REFCLKB Switching Characteristics Over the Operating Range
70 2 2
% ns ns
Notes 16. Tested initially and after any design or process changes that may affect these parameters, but not 100% tested. 17. The ratio of rise time to falling time must not vary by greater than 2:1. 18. For a given operating frequency, neither rise or fall specification can be greater than 20% of the clock-cycle period or the data sheet maximum time. 19. All transmit AC timing parameters measured with 1ns typical rise time and fall time. 20. Parallel data output specifications are only valid if all outputs are loaded with similar DC and AC loads. 21. Receiver UI (Unit Interval) is calculated as 1/(fTRG * 20) (when TRGRATEA = 1) or 1/(fTRG * 10) (when TRGRATEA = 0). In an operating link this is equivalent to tB. 22. The duty cycle specification is a simultaneous condition with the tREFH and tREFL parameters. This means that at faster character rates the REFCLKB duty cycle cannot be as large as 30%-70%.
Document #: 38-02100 Rev. *C
Page 20 of 28
[+] Feedback
CYV15G0104TRB
CYV15G0104TRB AC Electrical Characteristics (continued)
Parameter tTREFDS Description Transmit Data Set-up Time to REFCLKB - Full Rate (TXRATEB = 0, TXCKSELB = 1) Transmit Data Set-up Time to REFCLKB - Half Rate (TXRATEB = 1, TXCKSELB = 1) tTREFDH Transmit Data Hold Time from REFCLKB - Full Rate (TXRATEB= 0, TXCKSELB = 1) Transmit Data Hold Time from REFCLKB - Half Rate (TXRATEB = 1, TXCKSELB = 1) CYV15G0104TRB TRGCLKA Switching Characteristics Over the Operating Range fTRG tREFCLK tTRGH tTRGL tTRGD
[23]
Min. 2.4 2.3 1.0 1.6
Max
Unit ns ns ns ns
TRGCLKA Clock Frequency TRGCLKA Period = 1/fTRG TRGCLKA HIGH Time (TRGRATEA = 1)(Half Rate) TRGCLKA HIGH Time (TRGRATEA = 0)(Full Rate) TRGCLKA LOW Time (TRGRATEA = 1)(Half Rate) TRGCLKA LOW Time (TRGRATEA = 0)(Full Rate) TRGCLKA Duty Cycle TRGCLKA Rise Time (20%-80%) TRGCLKA Fall Time (20%-80%) TRGCLKA Frequency Referenced to Received Clock Frequency Bus Configuration Data Hold Bus Configuration Data Setup Bus Configuration WREN Pulse Width JTAG Test Clock Frequency JTAG Test Clock Period Device RESET Pulse Width Description Bit Time CML Output Rise Time 20-80% (CML Test Load) SPDSELx = HIGH SPDSELx= MID SPDSELx =LOW Condition
19.5 6.6 5.9 2.9
[16]
150 51.28
MHz ns ns ns ns ns
5.9 2.9[16] 30 70 2 2 -0.15 0 10 10 20 50 30 Min. 660 50 100 180 50 100 180 Max. 5128 270 500 1000 270 500 1000 +0.15
% ns ns % ns ns ns MHz ns ns Unit ps ps ps ps ps ps ps
tTRGR [16, 17, 18] tTRGF[16, 17, 18] tTRGRX[24] tDATAH tDATAS tWRENP fTCLK tTCLK tRST Parameter tB tRISE[16]
CYV15G0104TRB Bus Configuration Write Timing Characteristics Over the Operating Range
CYV15G0104TRB JTAG Test Clock Characteristics Over the Operating Range
CYV15G0104TRB Device RESET Characteristics Over the Operating Range CYV15G0104TRB Transmitter and Reclocker Serial Output Characteristics Over the Operating Range
tFALL[16]
CML Output Fall Time 80-20% (CML Test Load)
SPDSELx = HIGH SPDSELx = MID SPDSELx =LOW
Notes 23. The duty cycle specification is a simultaneous condition with the tTRGH and tTRGL parameters. This means that at faster character rates the TRGCLKA duty cycle cannot be as large as 30%-70%. 24. TRGCLKA has no phase or frequency relationship with the recovered clock(s) and only acts as a centering reference to reduce clock synchronization time. TRGCLKA must be within 1500 PPM (0.15%) of the transmitter PLL reference (REFCLK) frequency. Although transmitting to a HOTLink II receiver channel necessitates the frequency difference between the transmitter and receiver reference clocks to be within 1500-PPM, the stability of the crystal needs to be within the limits specified by the appropriate standard when transmitting to a remote receiver that is compliant to that standard.
Document #: 38-02100 Rev. *C
Page 21 of 28
[+] Feedback
CYV15G0104TRB
PLL Characteristics
Parameter tJTGENSD[16, 25] tJTGENHD tTXLOCK tJRGENSD[16, 26] tJRGENHD[16, 26] tRXLOCK tRXUNLOCK
[16, 25]
Description Transmit Jitter Generation - SD Data Rate Transmit Jitter Generation - HD Data Rate Transmit PLL lock to REFCLKB Reclocker Jitter Generation - SD Data Rate Reclocker Jitter Generation - HD Data Rate Receive PLL lock to input data stream (cold start) Receive PLL lock to input data stream Receive PLL Unlock Rate
Condition REFCLKB = 27 MHz REFCLKB = 148.5 MHz
Min.
Typ. 200 76
Max.
Unit ps ps
CYV15G0104TRB Transmitter Output PLL Characteristics
200 TRGCLKA = 27 MHz TRGCLKA = 148.5 MHz 133 107 376k 376k 46
s ps ps UI UI UI
CYV15G0104TRB Reclocker Output PLL Characteristics
CYV15G0104TRB Receive PLL Characteristics Over the Operating Range
Capacitance [16]
Parameter CINTTL CINPECL Description TTL Input Capacitance PECL input Capacitance Test Conditions TA = 25C, f0 = 1 MHz, VCC = 3.3V TA = 25C, f0 = 1 MHz, VCC = 3.3V Max. 7 4 Unit pF pF
CYV15G0104TRB HOTLink II Transmitter Switching Waveforms
Transmit Interface Write Timing TXCLKB selected
TXCLKB
tTXCLK tTXCLKH tTXCLKL
tTXDS
TXDB[9:0]
tTXDH
Transmit Interface Write Timing REFCLKB selected TXRATEB = 0
REFCLKB
tREFCLK tREFH tREFL
tTREFDS
TXDB[9:0]
tTREFDH
Notes 25. While sending BIST data at the corresponding data rate, after 10,000 histogram hits, time referenced to REFCLKB input. 26. Receiver input stream is BIST data from the transmit channel. This data is reclocked and output to a wide-bandwidth digital sampling oscilloscope. The measurement was recorded after 10,000 histogram hits, time referenced to REFCLKB of the transmit channel.
Document #: 38-02100 Rev. *C
Page 22 of 28
[+] Feedback
CYV15G0104TRB
CYV15G0104TRB HOTLink II Transmitter Switching Waveforms (continued)
Transmit Interface Write Timing REFCLKB selected TXRATEB = 1
REFCLKB
Note 27
tREFCLK tREFH tREFL
tTREFDS
TXDB[9:0]
tTREFDH
tTREFDS
tTREFDH
Transmit Interface TXCLKOB Timing TXRATE = 1
REFCLKB
tREFCLK tREFH tREFL
Note 28
tTXCLKO
Note 29
TXCLKOB (internal)
Transmit Interface TXCLKOB Timing tREFH TXRATEB = 0
REFCLKB
tREFCLK tREFL
Note28
Note29
tTXCLKO
TXCLKOB
Notes 27. When REFCLKB is configured for half-rate operation (TXRATEB = 1) and data is captured using REFCLKB instead of a TXCLKB clock. Data is captured using both the rising and falling edges of REFCLKB. 28. The TXCLKOB output remains at the character rate regardless of the state of TXRATEB and does not follow the duty cycle of REFCLKB. 29. The rising edge of TXCLKOB output has no direct phase relationship to the REFCLKB input.
Document #: 38-02100 Rev. *C
Page 23 of 28
[+] Feedback
CYV15G0104TRB
Switching Waveforms for the CYV15G0104TRB HOTLink II Receiver
Receive Interface Read Timing RXRATEA = 0
RXCLKA+
tRXCLKP
RXCLKA-
tRXDV-
RXDA[9:0]
tRXDV+ Receive Interface Read Timing RXRATEA = 1
RXCLKA+
tRXCLKP
RXCLKA-
tRXDV-
RXDA[9:0]
tRXDV+ Bus Configuration Write Timing
ADDR[2:0]
DATA[6:0]
tWRENP
WREN
tDATAS tDATAH
Document #: 38-02100 Rev. *C
Page 24 of 28
[+] Feedback
CYV15G0104TRB
Table 7. Package Coordinate Signal Allocation Ball ID A01 A02 A03 A04 A05 A06 A07 A08 A09 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 B01 B02 B03 B04 B05 B06 B07 B08 B09 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 C01 C02 C03 Signal Name NC NC NC NC VCC NC TOUTB1- GND GND TOUTB2- INA1- ROUTA1- GND INA2- ROUTA2- VCC VCC NC VCC NC VCC NC VCC NC VCC VCC TOUTB1+ GND NC TOUTB2+ INA1+ ROUTA1+ GND INA2+ ROUTA2+ VCC NC NC NC NC TDI TMS VCC Signal Type NO CONNECT NO CONNECT NO CONNECT NO CONNECT POWER NO CONNECT CML OUT GROUND GROUND CML OUT CML IN CML OUT GROUND CML IN CML OUT POWER POWER NO CONNECT POWER NO CONNECT POWER NO CONNECT POWER NO CONNECT POWER POWER CML OUT GROUND NO CONNECT CML OUT CML IN CML OUT GROUND CML IN CML OUT POWER NO CONNECT NO CONNECT NO CONNECT NO CONNECT LVTTL IN PU LVTTL IN PU POWER Ball ID C07 C08 C09 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 D01 D02 D03 D04 D05 D06 D07 D08 D09 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 E01 E02 E03 E04 E17 E18 E19 E20 F01 Signal Name NC GND DATA[6] DATA[4] DATA[2] DATA[0] GND NC SPDSELB VCC LDTDEN TRST GND TDO TCLK RESET VCC INSELA VCC ULCA NC GND DATA[5] DATA[3] DATA[1] GND GND GND NC VCC NC VCC SCANEN2 TMEN3 VCC VCC VCC VCC VCC VCC VCC VCC NC Signal Type NO CONNECT GROUND LVTTL IN PU LVTTL IN PU LVTTL IN PU LVTTL IN PU GROUND NO CONNECT 3-LEVEL SEL POWER LVTTL IN PU LVTTL IN PU GROUND LVTTL 3-S OUT LVTTL IN PD LVTTL IN PU POWER LVTTL IN POWER LVTTL IN PU NO CONNECT GROUND LVTTL IN PU LVTTL IN PU LVTTL IN PU GROUND GROUND GROUND NO CONNECT POWER NO CONNECT POWER LVTTL IN PD LVTTL IN PD POWER POWER POWER POWER POWER POWER POWER POWER NO CONNECT Ball ID F17 F18 F19 F20 G01 G02 G03 G04 G17 G18 G19 G20 H01 H02 H03 H04 H17 H18 H19 H20 J01 J02 J03 J04 J17 J18 J19 J20 K01 K02 K03 K04 K17 K18 K19 K20 L01 L02 L03 L04 L17 L18 L19 Signal Name VCC NC NC NC GND WREN GND GND NC NC SPDSELA NC GND GND GND GND GND GND GND GND GND GND GND GND NC NC NC NC NC NC GND GND NC NC NC NC NC NC NC GND NC NC NC Signal Type POWER NO CONNECT NO CONNECT NO CONNECT GROUND LVTTL IN PU GROUND GROUND NO CONNECT NO CONNECT 3-LEVEL SEL NO CONNECT GROUND GROUND GROUND GROUND GROUND GROUND GROUND GROUND GROUND GROUND GROUND GROUND NO CONNECT NO CONNECT NO CONNECT NO CONNECT NO CONNECT NO CONNECT GROUND GROUND NO CONNECT NO CONNECT NO CONNECT NO CONNECT NO CONNECT NO CONNECT NO CONNECT GROUND NO CONNECT NO CONNECT NO CONNECT Page 25 of 28
Document #: 38-02100 Rev. *C
[+] Feedback
CYV15G0104TRB
Table 7. Package Coordinate Signal Allocation (continued) Ball ID C04 C05 C06 M03 M04 M17 M18 M19 M20 N01 N02 N03 N04 N17 N18 N19 N20 P01 P02 P03 P04 P17 P18 P19 P20 R01 R02 R03 R04 R17 R18 R19 R20 T01 T02 T03 T04 T17 T18 T19 T20 U01 U02 Signal Name VCC VCC NC NC NC NC NC NC GND GND GND GND GND GND GND GND GND NC NC NC NC GND GND GND GND NC NC NC NC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC TXDB[0] TXDB[1] Signal Type POWER POWER NO CONNECT NO CONNECT NO CONNECT NO CONNECT NO CONNECT NO CONNECT GROUND GROUND GROUND GROUND GROUND GROUND GROUND GROUND GROUND NO CONNECT NO CONNECT NO CONNECT NO CONNECT GROUND GROUND GROUND GROUND NO CONNECT NO CONNECT NO CONNECT NO CONNECT POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER LVTTL IN LVTTL IN Ball ID F02 F03 F04 U03 U04 U05 U06 U07 U08 U09 U10 U11 U12 U13 U14 U15 U16 U17 U18 U19 U20 V01 V02 V03 V04 V05 V06 V07 V08 V09 V10 V11 V12 V13 V14 V15 V16 V17 V18 V19 V20 W01 W02 Signal Name NC VCC NC TXDB[2] TXDB[9] VCC NC NC GND GND ADDR [0] REFCLKB- GND GND GND VCC VCC RXDA[4] VCC BISTSTA RXDA[0] TXDB[3] TXDB[4] TXDB[8] NC VCC NC NC GND NC GND REFCLKB+ RECLKOA GND GND VCC VCC RXDA[9] RXDA[5] RXDA[2] RXDA[1] TXDB[5] TXDB[7] Signal Type NO CONNECT POWER NO CONNECT LVTTL IN LVTTL IN POWER NO CONNECT NO CONNECT GROUND GROUND LVTTL IN PU PECL IN GROUND GROUND GROUND POWER POWER LVTTL OUT POWER LVTTL OUT LVTTL OUT LVTTL IN LVTTL IN LVTTL IN NO CONNECT POWER NO CONNECT NO CONNECT GROUND NO CONNECT GROUND PECL IN LVTTL OUT GROUND GROUND POWER POWER LVTTL OUT LVTTL OUT LVTTL OUT LVTTL OUT LVTTL IN LVTTL IN Page 26 of 28 Ball ID L20 M01 M02 W03 W04 W05 W06 W07 W08 W09 W10 W11 W12 W13 W14 W15 W16 W17 W18 W19 W20 Y01 Y02 Y03 Y04 Y05 Y06 Y07 Y08 Y09 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y19 Y20 Signal Name GND NC NC NC NC VCC NC NC GND ADDR [2] ADDR [1] RXCLKA+ REPDOA GND GND VCC VCC LFIA TRGCLKA+ RXDA[6] RXDA[3] TXDB[6] TXCLKB NC NC VCC NC NC GND TXCLKOB NC GND RXCLKA- GND GND VCC VCC TXERRB TRGCLKA- RXDA[8] RXDA[7] Signal Type GROUND NO CONNECT NO CONNECT NO CONNECT NO CONNECT POWER NO CONNECT NO CONNECT GROUND LVTTL IN PU LVTTL IN PU LVTTL OUT LVTTL OUT GROUND GROUND POWER POWER LVTTL OUT PECL IN LVTTL OUT LVTTL OUT LVTTL IN LVTTL IN PD NO CONNECT NO CONNECT POWER NO CONNECT NO CONNECT GROUND LVTTL OUT NO CONNECT GROUND LVTTL OUT GROUND GROUND POWER POWER LVTTL OUT PECL IN LVTTL OUT LVTTL OUT
Document #: 38-02100 Rev. *C
[+] Feedback
CYV15G0104TRB
Ordering Information
Speed Standard Standard Ordering Code CYV15G0104TRB-BGC CYV15G0104TRB-BGXC Package Name BL256 BL256 Package Type 256-Ball Thermally Enhanced Ball Grid Array Pb-Free 256-Ball Thermally Enhanced Ball Grid Array Operating Range Commercial Commercial
Package Diagram
Figure 3. 256-Lead L2 Ball Grid Array (27 x 27 x 1.57 mm) BL256
TOP VIEW
27.000.13 A1 CORNER I.D.
0.20(4X) A O0.15 M C O0.30 M C O0.750.15(256X)
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H J K L M N P R T U V W Y
BOTTOM VIEW (BALL SIDE)
A B
24.13
A1 CORNER I.D.
R 2.5 Max (4X)
27.000.13
12.065 1.27 24.13
A
B 1.570.175 0.97 REF. 0.15 C
0.50 MIN.
A
0.600.10 C
26 TYP.
0.15
C
SEATING PLANE
0.20 MIN TOP OF MOLD COMPOUND TO TOP OF BALLS
SIDE VIEW
SECTION A-A
51-85123-*E
HOTLink is a registered trademark and HOTLink II is a trademark of Cypress Semiconductor. All product and company names mentioned in this document may be the trademarks of their respective holders.
Document #: 38-02100 Rev. *C
Page 27 of 28
(c) Cypress Semiconductor Corporation, 2002-2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
CYV15G0104TRB
Document History Page
Document Title: CYV15G0104TRB Independent Clock HOTLink IITM Serializer and Reclocking Deserializer Document Number: 38-02100 REV. ** *A *B *C ECN NO. 244348 338721 384307 1034021 ISSUE DATE See ECN See ECN See ECN See ECN ORIG. OF CHANGE FRE SUA AGT UKK New Data Sheet Added Pb-Free package option availability Revised setup and hold times (tTXDH, tTREFDS, tTREFDH, tRXDv-, tRXDv+) Added clarification for the necessity of JTAG controller reset and the methods to implement it. DESCRIPTION OF CHANGE
Document #: 38-02100 Rev. *C
Page 28 of 28
[+] Feedback


▲Up To Search▲   

 
Price & Availability of CYV15G0104TRB

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X