 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| D200E Series Low Cost, 2W SIP Single & Dual Output DC/DC Converters Electrical Specifications Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: * 2W Output Power * Miniature SIP Case * UL Approved (File E245422) * Single & Dual Outputs * 1,000 VDC Isolation * >3.5 MHour MTBF * 24 Standard Models * LOWEST COST!! Input Parameter Input Voltage Range Input Filter Reverse Polarity Input Current Conditions 5 VDC Input 12 VDC Input 24 VDC Input Min. 4.5 10.8 21.6 Typ. 5.0 12.0 24.0 Max. 5.5 13.2 26.4 0.3 Conditions Dual Output , Balanced Loads For Vin Change of 1% Min. Typ. 1.0 0.1 1.2 100 120 0.02 Momentary (1.0 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 60 75 Conditions Ambient Min. -40 -55 Free Air Convection RH, Non-condensing 95 % Typ. +25 Max. +85 +125 Typ. Max. Units VDC M pF kHz Units C C 0.03 150 Max. 3.0 1.0 A Units % % % mV P - P % %/C VDC Units Internal Capacitor Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit See Model Selection Guide RoHS Compliant General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com Case Size (5V 12V & 24V Input Models) Case Material Weight 0.77 x 0.28 x 0.40 Inches (19.6 x 7.0 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.07 Oz (2.1g) Conditions MIL HDBK 217F, 25C, Gnd Benign Min. 3.5 Typ. Max. Units MHours Reliability Specifications Parameter MTBF Safety Standards Safety Approvals UL 1950, EN 60950, IEC 60950 UL, cUL; File No. E245422 Conditions 5 VDC Input 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 300 450 C mW VDC Units Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D201E D202E D203E D204E D205E D206E D207E D208E D211E D212E D213E D214E D215E D216E D217E D218E D221E D222E D223E D224E D225E D226E D227E D228E Input Output Load Voltage (VDC) Current (mA) Regulation Voltage Current Current Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) 5 4.5 - 5.5 494 30 5.0 400.0 40.0 15 5 4.5 - 5.5 488 30 9.0 222.0 23.0 15 5 4.5 - 5.5 476 30 12.0 167.0 17.0 15 5 4.5 - 5.5 476 30 15.0 133.0 14.0 15 5 4.5 - 5.5 488 30 5.0 200.0 20.0 15 5 4.5 - 5.5 482 30 9.0 111.0 12.0 15 5 4.5 - 5.5 470 30 12.0 83.0 9.0 15 5 4.5 - 5.5 470 30 15.0 67.0 7.0 15 12 10.8 - 13.2 203 15 5.0 400.0 40.0 15 12 10.8 - 13.2 201 15 9.0 222.0 23.0 15 12 10.8 - 13.2 196 15 12.0 167.0 17.0 15 12 10.8 - 13.2 196 15 15.0 133.0 14.0 15 12 10.8 - 13.2 201 15 5.0 200.0 20.0 15 12 10.8 - 13.2 198 15 9.0 111.0 12.0 15 12 10.8 - 13.2 194 15 12.0 83.0 9.0 15 12 10.8 - 13.2 194 15 15.0 67.0 7.0 15 24 21.6 - 26.4 100 8 5.0 400.0 40.0 15 24 21.6 - 26.4 99 8 9.0 222.0 23.0 15 24 21.6 - 26.4 97 8 12.0 167.0 17.0 15 24 21.6 - 26.4 97 8 15.0 133.0 14.0 15 24 21.6 - 26.4 99 8 5.0 200.0 20.0 15 24 21.6 - 26.4 98 8 9.0 111.0 12.0 15 24 21.6 - 26.4 96 8 12.0 83.0 9.0 15 24 21.6 - 26.4 96 8 15.0 67.0 7.0 15 Efficiency (%, Typ) 81 82 84 84 82 83 85 85 82 83 85 85 83 84 86 86 83 84 86 86 84 85 87 87 Fuse Rating Slow-Blow (mA) 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhance stability over temperature and input line variations. Recommended capacitor values are given in the table below. For applications requiring very low output noise levels, a simple LC filter should be effective. Output Capacitor Input Vin Vout Capacitor Single Dual 5 VDC 4.7 F 5 VDC 10.0 F 4.7 F 12 VDC 2.2 F 9 VDC 4.7 F 2.2 F 24 VDC 1.0 F 12 VDC 2.2 F 1.0 F 15 VDC 1.0 F 0.47 F 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Derating Curve g Mechanical Dimensions Pin Connections Pin 1 2 4 Single +Vin -Vin -Vout Dual +Vin -Vin -Vout Pin 5 6 Single No Pin +Vout Dual Common +Vout Notes: * All dimensions are typical in inches (mm) * Tolerance x.xx = 0.01 (0.25) * Pin 1 is marked by a "dot" or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com * 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 * FAX: (781) 344-8481 * E-Mail: sales@micropowerdirect.com |
Price & Availability of D206E
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |