Part Number Hot Search : 
HC32251 WA302 104M00 STP2N80 STUK051 645ET SZ5211 MIC49300
Product Description
Full Text Search
 

To Download CL7SG-G Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 CL7 Linear, 100mA, Constant Current LED Driver with Enable
Features
100mA 5% constant current drive Built-in reverse polarity protection Logic level enable Dimmable via EN pin Overtemperature protection 90V max rating for transient immunity
General Description
The CL7 is a linear fixed current regulator designed for driving high brightness LEDs at 100mA from nominal 12V, 24V, and 48V power supplies. With a maximum rating of 90V, it is able to withstand transients without the need for additional transient protection circuitry. The CL7 is offered in the Power SO-8 package. An active low enable input (EN) allows logic level control of the LED for on/off control or PWM dimming. The enable input has 100k pull-down resistance. For applications not needing an enable input, refer to the CL6 data sheet. Overtemperature protection shuts off the LED current when the die temperature rises above 135C (nominal). Full LED current resumes when the die temperature falls below 105C (nominal).
Applications
Flashlights Specialty lighting Low voltage signage Low voltage lighting This device is not rated for automotive applications!
Typical Application Circuit
VIN 100mA VDD Host Controller EN OUT
Control 100k
CL7
GND
CL7
Ordering Information
Device CL7
-G indicates package is RoHS compliant (`Green')
8-Lead Power SOIC CL7SG-G
Absolute Maximum Ratings
Supply voltage, VDD Output voltage, VOUT Enable voltage, VEN Operating junction temperature Storage temperature -25V to +100V -25V to +100V -0.5V to +6.5V -40C1 -65C to +150C
Pin Configurations
Power SO-8
GND GND GND GND VDD OUT NC EN
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Continuous operation of the device at the absolute rating level may affect device reliability. All voltages are referenced to device ground. 1. Maximum junction temperature internally limited.
Underside plate is GND
IOUT vs Temperature
IOUT (Normalized)
1.05 1.00 0.95
Pin Designation
Pin VDD OUT GND Name VDD Output Ground Enable Description Supply voltage for the CL7 Connect the LED between this pin and the supply voltage Circuit common Active low enable input - this input has an internal 100k pull-down resistance
0.90
EN
0.85 -50 -25 0 25 50 75
O
100 125
Temperature ( C)
Thermal Characteristics (Guaranteed by design - not production tested )
Symbol j-a TLIM THYS Parameter Thermal resistance, junction to ambient Overtemperature limit Overtemperature hysteresis Power SO-8 Min 120 Typ 67 135 30 Max 150 Units
O
Conditions
C/W Soldered to 2cm2 exposed copper area
O O
C C
-----
Recommended Operating Conditions (all voltages with respect to GND pin)
Symbol VDD VOUT TJ Parameter Supply voltage Voltage at OUT pin1 Junction temperature2 Normal Extended Normal Extended Min 6.5 6.5 4.0 4.0 -40 Typ Max 28 90 28 90 119 Units V V
o
Conditions -------
C
1. Continuous operation at high VOUT voltages may result in activation of overtemperature protection. Use appropriate heatsinking. 2. Maximum junction temperature internally limited.
2
CL7
Electrical Characteristics (Over normal recommended operating conditions unless otherwise specified. All voltages with respect
to GND pin. Production tested @ 25OC.)
Symbol IDD IOUT IOUT(OFF) VEN(ON) VEN(OFF) REN VOFF tON tOFF tRISE tFALL
Parameter Current into VDD pin Current into OUT pin1 Current into OUT pin with VDD pin open or EN=1 Enable voltage, on Enable voltage, off Enable pull-down resistance Voltage at VDD to shut off LED current On delay, EN to OUT Off delay, EN to OUT Current rise time, EN to OUT Current fall time, EN to OUT
Min 3.0 95 90 50 2.4 -
Typ 5.0 100 100 100 3.0 0.1 4.0 0.3
Max 10 105 110 120 10 0.8 1 -
Units mA mA A V V k V s s s s
Conditions --Normal conditions, 25C Normal conditions, full temp2 Extended conditions VDD = open ------IOUT < 10A EN = 0V EN = 5V EN = 0V EN = 5V
Timing
EN
t ON t RISE
90%
t OFF t FALL
IOUT
10%
Application Circuits
PWM Dimming
VIN
(1-D) * 100mA EN = 0: 107.5mA EN = 1: 7.5mA
2-Level LED Circuit
VIN
VDD PWM signal EN Control
100k
OUT EN
VDD Control
100k
OUT
CL7
GND
CL7
GND
D is the portion of time the PWM signal is high.
Minimum VIN is increased by LED drop.
3
CL7
8-Lead SOIC (Narrow Body w/Heat Slug) Package Outline (SG)
4.90x3.90mm body, 1.70mm height (max), 1.27mm pitch
D
8
D1
8 Exposed Thermal Pad Zone
1
Note 1 (Index Area D/2 x E1/2)
E1
E
E2
L2
Gauge Plane
1
1 L1
L
Seating Plane
Top View
A
Bottom View
View B
View B
h h A A2 e
Seating Plane Note 1
A1
b A
Side View
View A-A
Note 1: This chamfer feature is optional. If it is not present, then a Pin 1 identifier must be located in the index area indicated.The Pin 1 identifier may be either a mold, or an embedded metal or marked feature.
Symbol MIN Dimension NOM (mm) MAX
A 1.25 1.70
A1 0.00 0.15
A2 1.25 1.70
b 0.31 0.51
D 4.80 4.90 5.00
D1 3.30* 3.81*
E 5.80 6.00 6.20
E1 3.80 3.90 4.00
E2 2.29* 2.79*
e 1.27 BSC
h 0.25 0.50
L 0.40 1.27
L1
L2
0
O
1 5O 15O
1.04 0.25 REF BSC
8O
JEDEC Registration MS-012, Variation BA, Issue E, Sept. 2005. Dimensions marked with (*) are non-JEDEC dimensions. Drawings not to scale.
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to http://www.supertex.com/packaging.html.)
Doc.# DSFP-CL7 NR021407
4


▲Up To Search▲   

 
Price & Availability of CL7SG-G

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X