Part Number Hot Search : 
FFV36AK 20N36 RF2105 RAPH2SG 08100 FCX61903 6EJMS1 60040215
Product Description
Full Text Search
 

To Download H8-3022 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 REJ09B0352-0200
The revision list can be viewed directly by clicking the title page. The revision list summarizes the locations of revisions and additions. Details should always be checked by referring to the relevant text.
16
H8/3022 Group, H8/3022F-ZTAT
TM
Hardware Manual Renesas 16-Bit Single-Chip Microcomputer H8 Family / H8/300H Series H8/3022 HD64F3022F HD64F3022TE HD6433022F HD6433022TE H8/3021 HD6433021F HD6433021TE H8/3020 HD6433020F HD6433020TE
Rev.2.00 Revision date: Mar. 22, 2007
www.renesas.com
Notes regarding these materials
1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries.
Rev.2.00 Mar. 22, 2007 Page ii of xxiv REJ09B0352-0200
General Precautions in the Handling of MPU/MCU Products
The following usage notes are applicable to all MPU/MCU products from Renesas. For detailed usage notes on the products covered by this manual, refer to the relevant sections of the manual. If the descriptions under General Precautions in the Handling of MPU/MCU Products and in the body of the manual differ from each other, the description in the body of the manual takes precedence. 1. Handling of Unused Pins Handle unused pins in accord with the directions given under Handling of Unused Pins in the manual. The input pins of CMOS products are generally in the high-impedance state. In operation with an unused pin in the open-circuit state, extra electromagnetic noise is induced in the vicinity of LSI, an associated shoot-through current flows internally, and malfunctions may occur due to the false recognition of the pin state as an input signal. Unused pins should be handled as described under Handling of Unused Pins in the manual. 2. Processing at Power-on The state of the product is undefined at the moment when power is supplied. The states of internal circuits in the LSI are indeterminate and the states of register settings and pins are undefined at the moment when power is supplied. In a finished product where the reset signal is applied to the external reset pin, the states of pins are not guaranteed from the moment when power is supplied until the reset process is completed. In a similar way, the states of pins in a product that is reset by an on-chip power-on reset function are not guaranteed from the moment when power is supplied until the power reaches the level at which resetting has been specified. 3. Prohibition of Access to Reserved Addresses Access to reserved addresses is prohibited. The reserved addresses are provided for the possible future expansion of functions. Do not access these addresses; the correct operation of LSI is not guaranteed if they are accessed. 4. Clock Signals After applying a reset, only release the reset line after the operating clock signal has become stable. When switching the clock signal during program execution, wait until the target clock signal has stabilized. When the clock signal is generated with an external resonator (or from an external oscillator) during a reset, ensure that the reset line is only released after full stabilization of the clock signal. Moreover, when switching to a clock signal produced with an external resonator (or by an external oscillator) while program execution is in progress, wait until the target clock signal is stable. 5. Differences between Products Before changing from one product to another, i.e. to one with a different type number, confirm that the change will not lead to problems. The characteristics of MPU/MCU in the same group but having different type numbers may differ because of the differences in internal memory capacity and layout pattern. When changing to products of different type numbers, implement a system-evaluation test for each of the products.
Rev.2.00 Mar. 22, 2007 Page iii of xxiv REJ09B0352-0200
Rev.2.00 Mar. 22, 2007 Page iv of xxiv REJ09B0352-0200
Preface
The H8/3022 Group comprises high-performance single-chip microcomputers (MCUs) that integrate system supporting functions together with an H8/300H CPU core. The H8/300H CPU has a 32-bit internal architecture with sixteen 16-bit general registers, and a concise, optimized instruction set designed for speed. It can address a 16-Mbyte linear address space. The on-chip system supporting functions include ROM, RAM, a 16-bit integrated timer unit (ITU), a programmable timing pattern controller (TPC), a watchdog timer (WDT), a serial communication interface (SCI), an A/D converter, I/O ports, and other facilities. Of the two SCI channels, one has been expanded to support the ISO/IEC 7816-3 smart card interface. Functions have also been added to reduce power consumption in battery-powered applications: individual modules can be placed in standby, and the frequency of the system clock supplied to the chip can be divided down under software control. The five MCU operating modes offer a choice of expanded mode, single-chip mode, and address space size, enabling the H8/3022 Group to adapt quickly and flexibly to a variety of conditions. In addition to its masked-ROM versions, the H8/3022 Group has an F-ZTAT* version with user programmable on-chip flash memory that can be programmed on-board. These versions enable users to respond quickly and flexibly to changing application specifications. This manual describes the H8/3022 Group hardware. For details of the instruction set, refer to the H8/300H Series Programming Manual. Note: * F-ZTAT is a trademark of Renesas Technology Corp.
Rev.2.00 Mar. 22, 2007 Page v of xxiv REJ09B0352-0200
Rev.2.00 Mar. 22, 2007 Page vi of xxiv REJ09B0352-0200
Main Revisions for This Edition
Item All Page -- Revision (See Manual for Details) * * 2.3 Address Space Figure 2.2 Memory Map 18 Notification of change in company name amended (Before) Hitachi, Ltd. (After) Renesas Technology Corp. Product naming convention amended (Before) H8/3022 Series (After) H8/3022 Group
Figure amended
H'0000
H'FFFF
5.3.3 Interrupt Vector Table Table 5.3 Interrupt Sources, Vector Addresses, and Priority 5.5.4 Usage Notes Figure 5.9 IRQnF Flag when Interrupt Exception Handling is not Executed
94
Table amended Interrupt Source WOVI (interval timer)
105
Figure amended
IRQaF
1 read 0 written
1 read 0 written
IRQbF
1 read
1 IRQb written executed
0 read
0 written
(Inadvertent clearing) Generation condition (1) Generation condition (2)
7.1 Overview Table 7.1 Port Functions
131
Table amended
Port Port 9 Description Pins * 6-bit I/O port P95/SCK1/ IRQ5, P94/SCK0/ IRQ4, P93/RxD1, P92/RxD0, P91/TxD1, P90/TxD0 Mode 1 Mode 3 Mode 5 Mode 6 Mode 7 Input and output (SCK1, SCK0, RxD1, RxD0, TxD1, TxD0) for serial communication interfaces 1 and 0 (SCI0, 1), IRQ5 and IRQ4 input, and 6-bit generic input/output
Rev.2.00 Mar. 22, 2007 Page vii of xxiv REJ09B0352-0200
Item
Page
Revision (See Manual for Details) Figure amended
A 19 (output) Port 5 A 18 (output) A 17 (output) A 16 (output)
7.5.3 Pin Functions in 149 Each Mode Figure 7.13 Pin Functions in Modes 1 and 3 (Port 5)
8.4.8 Buffering Figure 8.52 Input Capture and Buffer Transfer Timing (Example)
263
Figure amended
TIOC pin Input capture signal TCNT GR BR M m n n M n+1 N n M N n N+1
8.4.9 ITU Output Timing Figure 8.55 Timing of Disabling of ITU Output by External Trigger (Example)
266
Figure amended
TIOCA1 pin Input capture signal TOER ITU output pins N ITU output ITU output N: Arbitrary setting (H'C1 to H'FF) H'C0 I/O port Generic input/output N ITU output ITU output H'C0 I/O port Generic input/output
9.2.5 Next Data Register A (NDRA)
293
Bit table amended
Bit Initial value Read/Write 7 NDR7 0 R/W 6 NDR6 0 R/W 5 NDR5 0 R/W 4 NDR4 0 R/W 3 NDR3 0 R/W 2 NDR2 0 R/W 1 NDR1 0 R/W 0 NDR0 0 R/W
Next data 7 to 4 These bits store the next output data for TPC output group 1
Next data 3 to 0 These bits store the next output data for TPC output group 0
9.4.2 Note on NonOverlapping Output
313
Description amended This can be accomplished by having the IMFA interrupt service routine write the next data in NDR. The next data must be written before the next compare match B occurs.
Rev.2.00 Mar. 22, 2007 Page viii of xxiv REJ09B0352-0200
Item 11.2.8 Bit Rate Register (BRR)
Page 350
Revision (See Manual for Details) Description amended The CPU can always read and write BRR. BRR is initialized to H'FF by a reset and in standby mode. The baud rate generator is controlled separately for the individual channels, so different values may be set for each. Table 11.3 shows examples of BRR settings in asynchronous mode. Table 11.4 shows examples of BRR settings in synchronous mode.
Table 11.3 Examples of Bit Rates and BRR Settings in Asynchronous Mode
352
Table amended
(MHz) 6 Bit Rate (bits/s) 110 150 300 n 2 2 1 N 106 77 155 Error (%) -0.44 0.16 0.16 n 2 2 2 N 212 155 77 12 Error (%) 0.03 0.16 0.16
11.3.4 Synchronous Operation Figure 11.17 Example of SCI Transmit Operation
382
Figure amended
Transmit direction
Serial clock
Serial data TDRE TEND TXI request
Bit 0
Bit 1
Bit 7
Bit 0
Bit 1
Bit 6
Bit 7
TXI interrupt handler writes data in TDR and clears TDRE flag to 0 1 frame
TXI request
TEI request
15.8.3 Error Protection Figure 15.13 Flash Memory State Transitions (Modes 5, 6, and 7 (on-chip ROM enabled), high level applied to FWE pin) 16.2.1 Connecting a Crystal Resonator Table 16.2 Crystal Resonator Parameters
485
Figure amended
Error protection mode (software standby) RD VF PR ER INIT FLER= 1
504
Preliminary deleted
Rev.2.00 Mar. 22, 2007 Page ix of xxiv REJ09B0352-0200
Item 18. Electrical Characteristics 18.2.5 Flash Memory Characteristics Table 18.15 Flash Memory Characteristics A.1 Instruction List Table A.1 Instruction Set 1. Data transfer instructions
Page 525 to 558 548
Revision (See Manual for Details) Preliminary deleted Table amended
Item Erase Wait time after SWE bit setting*1 Wait time after ESU bit setting*1 Wait time after E bit setting*1,*5 Symbol tsswe tsesu tse 1 100 10 Min Typ 1 100 10 Max -- -- 100 Unit s s ms Erase wait time Comments
561
Table amended
Operand Size
B B B
Mnemonic MOV.B @ERs+, Rd
Operation @ERs Rd8 ERs32+1 ERs32 Rs8 @(d:16, ERd) Rs8 @(d:24, ERd)
MOV.B Rs, @(d:16, ERd) MOV.B Rs, @(d:24, ERd)
2. Arithmetic instructions
565
Table amended
Operand Size
L
Mnemonic EXTS.L ERd
Operation ( of ERd32) ( of ERd32)
8. Block transfer instructions
573
Table amended
Operand Size
Mnemonic EEPMOV. W
Operation
-- if R4 0 then repeat @R5 @R6 R5+1 R5 R6+1 R6 R4-1 R4 until R4=0 else next;
Rev.2.00 Mar. 22, 2007 Page x of xxiv REJ09B0352-0200
Item A.2 Operation Code Maps Table A.2 Operation Code Map (2)
Page 575
Revision (See Manual for Details) Table amended
BH AH AL 1B 8 SUBS 9
Table A.2 Operation Code Map (3)
576
Table amended
CL AH ALBH BLCH
A.3 Number of States 581 Required for Execution Table A.4 Number of Cycles per Instruction
Table amended
Instruction BSR Mnemonic BSR d:16 Normal Advanced Word Data Access M Internal Operation N 2 2
B.2 Function PADDR--Port A Data Direction Register
641
Bit table amended
Modes 3 and 6 Modes 1, 5 and 7 Initial value Read/Write Initial value Read/Write
Rev.2.00 Mar. 22, 2007 Page xi of xxiv REJ09B0352-0200
All trademarks and registered trademarks are the property of their respective owners.
Rev.2.00 Mar. 22, 2007 Page xii of xxiv REJ09B0352-0200
Contents
Section 1 Overview.............................................................................................................
1.1 1.2 1.3 1 Overview........................................................................................................................... 1 Block Diagram .................................................................................................................. 5 Pin Description.................................................................................................................. 6 1.3.1 Pin Arrangement .................................................................................................. 6 1.3.2 Pin Functions ....................................................................................................... 7 Pin Functions .................................................................................................................... 11
1.4
Section 2 CPU ...................................................................................................................... 15
2.1 Overview........................................................................................................................... 2.1.1 Features................................................................................................................ 2.1.2 Differences from H8/300 CPU............................................................................. CPU Operating Modes ...................................................................................................... Address Space ................................................................................................................... Register Configuration ...................................................................................................... 2.4.1 Overview.............................................................................................................. 2.4.2 General Registers ................................................................................................. 2.4.3 Control Registers ................................................................................................. 2.4.4 Initial CPU Register Values ................................................................................. Data Formats ..................................................................................................................... 2.5.1 General Register Data Formats ............................................................................ 2.5.2 Memory Data Formats ......................................................................................... Instruction Set ................................................................................................................... 2.6.1 Instruction Set Overview ..................................................................................... 2.6.2 Instructions and Addressing Modes ..................................................................... 2.6.3 Tables of Instructions Classified by Function...................................................... 2.6.4 Basic Instruction Formats .................................................................................... 2.6.5 Notes on Use of Bit Manipulation Instructions.................................................... Addressing Modes and Effective Address Calculation ..................................................... 2.7.1 Addressing Modes ............................................................................................... 2.7.2 Effective Address Calculation.............................................................................. Processing States............................................................................................................... 2.8.1 Overview.............................................................................................................. 2.8.2 Program Execution State...................................................................................... 2.8.3 Exception-Handling State .................................................................................... 2.8.4 Exception-Handling Sequences ........................................................................... 2.8.5 Reset State............................................................................................................ 2.8.6 Power-Down State ............................................................................................... Basic Operational Timing ................................................................................................. 15 15 16 17 18 19 19 20 21 22 23 23 24 26 26 27 29 39 40 41 41 44 48 48 49 49 51 52 52 53
2.2 2.3 2.4
2.5
2.6
2.7
2.8
2.9
Rev.2.00 Mar. 22, 2007 Page xiii of xxiv REJ09B0352-0200
2.9.1 2.9.2 2.9.3 2.9.4
Overview.............................................................................................................. On-Chip Memory Access Timing........................................................................ On-Chip Supporting Module Access Timing ...................................................... Access to External Address Space .......................................................................
53 53 54 55
Section 3 MCU Operating Modes .................................................................................. 57
3.1 Overview........................................................................................................................... 3.1.1 Operating Mode Selection ................................................................................... 3.1.2 Register Configuration......................................................................................... Mode Control Register (MDCR) ...................................................................................... System Control Register (SYSCR) ................................................................................... Operating Mode Descriptions ........................................................................................... 3.4.1 Mode 1 ................................................................................................................. 3.4.2 Mode 3 ................................................................................................................. 3.4.3 Mode 5 ................................................................................................................. 3.4.4 Mode 6 ................................................................................................................. 3.4.5 Mode 7 ................................................................................................................. Pin Functions in Each Operating Mode ............................................................................ Memory Map in Each Operating Mode ............................................................................ 57 57 58 59 60 62 62 62 62 62 62 63 63
3.2 3.3 3.4
3.5 3.6
Section 4 Exception Handling ......................................................................................... 71
4.1 Overview........................................................................................................................... 4.1.1 Exception Handling Types and Priority............................................................... 4.1.2 Exception Handling Operation............................................................................. 4.1.3 Exception Vector Table ....................................................................................... Reset.................................................................................................................................. 4.2.1 Overview.............................................................................................................. 4.2.2 Reset Sequence .................................................................................................... 4.2.3 Interrupts after Reset............................................................................................ Interrupts........................................................................................................................... Trap Instruction................................................................................................................. Stack Status after Exception Handling.............................................................................. Notes on Stack Usage ....................................................................................................... 71 71 71 72 74 74 74 76 76 77 77 78
4.2
4.3 4.4 4.5 4.6
Section 5 Interrupt Controller .......................................................................................... 79
5.1 Overview........................................................................................................................... 5.1.1 Features................................................................................................................ 5.1.2 Block Diagram..................................................................................................... 5.1.3 Pin Configuration................................................................................................. 5.1.4 Register Configuration......................................................................................... Register Descriptions ........................................................................................................ 79 79 80 81 81 82
5.2
Rev.2.00 Mar. 22, 2007 Page xiv of xxiv REJ09B0352-0200
5.3
5.4
5.5
5.2.1 System Control Register (SYSCR) ...................................................................... 5.2.2 Interrupt Priority Registers A and B (IPRA, IPRB) ............................................. 5.2.3 IRQ Status Register (ISR).................................................................................... 5.2.4 IRQ Enable Register (IER) .................................................................................. 5.2.5 IRQ Sense Control Register (ISCR) .................................................................... Interrupt Sources ............................................................................................................... 5.3.1 External Interrupts ............................................................................................... 5.3.2 Internal Interrupts................................................................................................. 5.3.3 Interrupt Vector Table.......................................................................................... Interrupt Operation............................................................................................................ 5.4.1 Interrupt Handling Process................................................................................... 5.4.2 Interrupt Sequence ............................................................................................... 5.4.3 Interrupt Response Time...................................................................................... Usage Notes ...................................................................................................................... 5.5.1 Contention between Interrupt and Interrupt-Disabling Instruction ...................... 5.5.2 Instructions that Inhibit Interrupts........................................................................ 5.5.3 Interrupts during EEPMOV Instruction Execution .............................................. 5.5.4 Usage Notes .........................................................................................................
82 84 89 90 91 92 92 93 93 96 96 101 102 103 103 104 104 104
Section 6 Bus Controller.................................................................................................... 107
6.1 Overview........................................................................................................................... 6.1.1 Features................................................................................................................ 6.1.2 Block Diagram ..................................................................................................... 6.1.3 Pin Configuration................................................................................................. 6.1.4 Register Configuration......................................................................................... Register Descriptions ........................................................................................................ 6.2.1 Access State Control Register (ASTCR) ............................................................. 6.2.2 Wait Control Register (WCR).............................................................................. 6.2.3 Wait State Controller Enable Register (WCER) .................................................. 6.2.4 Address Control Register (ADRCR).................................................................... Operation........................................................................................................................... 6.3.1 Area Division ....................................................................................................... 6.3.2 Bus Control Signal Timing .................................................................................. 6.3.3 Wait Modes.......................................................................................................... 6.3.4 Interconnections with Memory (Example) .......................................................... Usage Notes ...................................................................................................................... 6.4.1 Register Write Timing ......................................................................................... 6.4.2 Precautions on setting ASTCR and ABWCR* .................................................... 107 107 108 109 109 110 110 111 112 113 115 115 117 119 125 127 127 127
6.2
6.3
6.4
Section 7 I/O Ports .............................................................................................................. 129
7.1 Overview........................................................................................................................... 129
Rev.2.00 Mar. 22, 2007 Page xv of xxiv REJ09B0352-0200
7.2
Port 1................................................................................................................................. 7.2.1 Overview.............................................................................................................. 7.2.2 Register Descriptions ........................................................................................... 7.2.3 Pin Functions in Each Mode ................................................................................ 7.3 Port 2................................................................................................................................. 7.3.1 Overview.............................................................................................................. 7.3.2 Register Descriptions ........................................................................................... 7.3.3 Pin Functions in Each Mode ................................................................................ 7.3.4 Input Pull-Up Transistors..................................................................................... 7.4 Port 3................................................................................................................................. 7.4.1 Overview.............................................................................................................. 7.4.2 Register Descriptions ........................................................................................... 7.4.3 Pin Functions in Each Mode ................................................................................ 7.5 Port 5................................................................................................................................. 7.5.1 Overview.............................................................................................................. 7.5.2 Register Descriptions ........................................................................................... 7.5.3 Pin Functions in Each Mode ................................................................................ 7.5.4 Input Pull-Up Transistors..................................................................................... 7.6 Port 6................................................................................................................................. 7.6.1 Overview.............................................................................................................. 7.6.2 Register Descriptions ........................................................................................... 7.6.3 Pin Functions in Each Mode ................................................................................ 7.7 Port 7................................................................................................................................. 7.7.1 Overview.............................................................................................................. 7.7.2 Register Description............................................................................................. 7.8 Port 8................................................................................................................................. 7.8.1 Overview.............................................................................................................. 7.8.2 Register Descriptions ........................................................................................... 7.8.3 Pin Functions ....................................................................................................... 7.9 Port 9................................................................................................................................. 7.9.1 Overview.............................................................................................................. 7.9.2 Register Descriptions ........................................................................................... 7.9.3 Pin Functions ....................................................................................................... 7.10 Port A................................................................................................................................ 7.10.1 Overview.............................................................................................................. 7.10.2 Register Descriptions ........................................................................................... 7.10.3 Pin Functions ....................................................................................................... 7.11 Port B ................................................................................................................................ 7.11.1 Overview.............................................................................................................. 7.11.2 Register Descriptions ........................................................................................... 7.11.3 Pin Functions .......................................................................................................
Rev.2.00 Mar. 22, 2007 Page xvi of xxiv REJ09B0352-0200
133 133 133 135 137 137 138 140 142 143 143 143 145 146 146 146 149 150 151 151 151 154 157 157 157 159 159 159 161 162 162 162 164 166 166 167 169 176 176 176 178
Section 8 16-Bit Integrated Timer Unit (ITU) ............................................................ 185
8.1 Overview........................................................................................................................... 8.1.1 Features................................................................................................................ 8.1.2 Block Diagrams ................................................................................................... 8.1.3 Pin Configuration................................................................................................. 8.1.4 Register Configuration......................................................................................... Register Descriptions ........................................................................................................ 8.2.1 Timer Start Register (TSTR)................................................................................ 8.2.2 Timer Synchro Register (TSNC) ......................................................................... 8.2.3 Timer Mode Register (TMDR) ............................................................................ 8.2.4 Timer Function Control Register (TFCR)............................................................ 8.2.5 Timer Output Master Enable Register (TOER) ................................................... 8.2.6 Timer Output Control Register (TOCR) .............................................................. 8.2.7 Timer Counters (TCNT) ...................................................................................... 8.2.8 General Registers (GRA, GRB)........................................................................... 8.2.9 Buffer Registers (BRA, BRB) ............................................................................. 8.2.10 Timer Control Registers (TCR) ........................................................................... 8.2.11 Timer I/O Control Register (TIOR) ..................................................................... 8.2.12 Timer Status Register (TSR)................................................................................ 8.2.13 Timer Interrupt Enable Register (TIER) .............................................................. CPU Interface.................................................................................................................... 8.3.1 16-Bit Accessible Registers ................................................................................. 8.3.2 8-Bit Accessible Registers ................................................................................... Operation........................................................................................................................... 8.4.1 Overview.............................................................................................................. 8.4.2 Basic Functions.................................................................................................... 8.4.3 Synchronization ................................................................................................... 8.4.4 PWM Mode.......................................................................................................... 8.4.5 Reset-Synchronized PWM Mode......................................................................... 8.4.6 Complementary PWM Mode ............................................................................... 8.4.7 Phase Counting Mode .......................................................................................... 8.4.8 Buffering.............................................................................................................. 8.4.9 ITU Output Timing .............................................................................................. Interrupts ........................................................................................................................... 8.5.1 Setting of Status Flags.......................................................................................... 8.5.2 Clearing of Status Flags ....................................................................................... 8.5.3 Interrupt Sources.................................................................................................. Usage Notes ...................................................................................................................... 185 185 188 193 195 198 198 199 202 205 207 210 211 212 213 214 217 219 221 223 223 225 226 226 227 237 239 243 246 256 258 265 267 267 269 270 271
8.2
8.3
8.4
8.5
8.6
Section 9 Programmable Timing Pattern Controller ................................................. 287
9.1 Overview........................................................................................................................... 287
Rev.2.00 Mar. 22, 2007 Page xvii of xxiv REJ09B0352-0200
9.2
9.3
9.4
9.1.1 Features................................................................................................................ 9.1.2 Block Diagram..................................................................................................... 9.1.3 Pin Configuration................................................................................................. 9.1.4 Register Configuration......................................................................................... Register Descriptions ........................................................................................................ 9.2.1 Port A Data Direction Register (PADDR) ........................................................... 9.2.2 Port A Data Register (PADR).............................................................................. 9.2.3 Port B Data Direction Register (PBDDR) ........................................................... 9.2.4 Port B Data Register (PBDR) .............................................................................. 9.2.5 Next Data Register A (NDRA) ............................................................................ 9.2.6 Next Data Register B (NDRB)............................................................................. 9.2.7 Next Data Enable Register A (NDERA).............................................................. 9.2.8 Next Data Enable Register B (NDERB) .............................................................. 9.2.9 TPC Output Control Register (TPCR) ................................................................. 9.2.10 TPC Output Mode Register (TPMR) ................................................................... Operation .......................................................................................................................... 9.3.1 Overview.............................................................................................................. 9.3.2 Output Timing...................................................................................................... 9.3.3 Normal TPC Output............................................................................................. 9.3.4 Non-Overlapping TPC Output............................................................................. Usage Notes ...................................................................................................................... 9.4.1 Operation of TPC Output Pins ............................................................................. 9.4.2 Note on Non-Overlapping Output........................................................................
287 288 289 290 291 291 291 292 292 293 295 297 298 299 302 305 305 306 307 309 312 312 312
Section 10 Watchdog Timer............................................................................................. 315
10.1 Overview........................................................................................................................... 10.1.1 Features................................................................................................................ 10.1.2 Block Diagram..................................................................................................... 10.1.3 Pin Configuration................................................................................................. 10.1.4 Register Configuration......................................................................................... 10.2 Register Descriptions ........................................................................................................ 10.2.1 Timer Counter (TCNT)........................................................................................ 10.2.2 Timer Control/Status Register (TCSR)................................................................ 10.2.3 Reset Control/Status Register (RSTCSR) ............................................................ 10.2.4 Notes on Register Access..................................................................................... 10.3 Operation .......................................................................................................................... 10.3.1 Watchdog Timer Operation ................................................................................. 10.3.2 Interval Timer Operation ..................................................................................... 10.3.3 Timing of Setting of Overflow Flag (OVF) ......................................................... 10.3.4 Timing of Setting of Watchdog Timer Reset Bit (WRST) .................................. 10.4 Interrupts...........................................................................................................................
Rev.2.00 Mar. 22, 2007 Page xviii of xxiv REJ09B0352-0200
315 315 316 316 317 318 318 319 321 323 325 325 326 327 328 329
10.5 Usage Notes ...................................................................................................................... 329
Section 11 Serial Communication Interface ................................................................ 331
11.1 Overview........................................................................................................................... 11.1.1 Features................................................................................................................ 11.1.2 Block Diagram ..................................................................................................... 11.1.3 Pin Configuration................................................................................................. 11.1.4 Register Configuration......................................................................................... 11.2 Register Descriptions ........................................................................................................ 11.2.1 Receive Shift Register (RSR) .............................................................................. 11.2.2 Receive Data Register (RDR) .............................................................................. 11.2.3 Transmit Shift Register (TSR) ............................................................................. 11.2.4 Transmit Data Register (TDR)............................................................................. 11.2.5 Serial Mode Register (SMR)................................................................................ 11.2.6 Serial Control Register (SCR).............................................................................. 11.2.7 Serial Status Register (SSR) ................................................................................ 11.2.8 Bit Rate Register (BRR) ...................................................................................... 11.3 Operation........................................................................................................................... 11.3.1 Overview.............................................................................................................. 11.3.2 Operation in Asynchronous Mode ....................................................................... 11.3.3 Multiprocessor Communication........................................................................... 11.3.4 Synchronous Operation........................................................................................ 11.4 SCI Interrupts.................................................................................................................... 11.5 Usage Notes ...................................................................................................................... 331 331 333 334 335 336 336 336 337 337 338 342 346 350 359 359 362 371 378 387 388
Section 12 Smart Card Interface ..................................................................................... 395
12.1 Overview........................................................................................................................... 12.1.1 Features................................................................................................................ 12.1.2 Block Diagram ..................................................................................................... 12.1.3 Pin Configuration................................................................................................. 12.1.4 Register Configuration......................................................................................... 12.2 Register Descriptions ........................................................................................................ 12.2.1 Smart Card Mode Register (SCMR) .................................................................... 12.2.2 Serial Status Register (SSR) ................................................................................ 12.3 Operation........................................................................................................................... 12.3.1 Overview.............................................................................................................. 12.3.2 Pin Connections ................................................................................................... 12.3.3 Data Format ......................................................................................................... 12.3.4 Register Settings .................................................................................................. 12.3.5 Clock.................................................................................................................... 12.3.6 Data Transfer Operations ..................................................................................... 395 395 396 397 397 398 398 400 402 402 402 404 406 408 410
Rev.2.00 Mar. 22, 2007 Page xix of xxiv REJ09B0352-0200
12.4 Usage Note........................................................................................................................ 416
Section 13 A/D Converter................................................................................................. 419
13.1 Overview........................................................................................................................... 13.1.1 Features................................................................................................................ 13.1.2 Block Diagram..................................................................................................... 13.1.3 Pin Configuration................................................................................................. 13.1.4 Register Configuration......................................................................................... 13.2 Register Descriptions ........................................................................................................ 13.2.1 A/D Data Registers A to D (ADDRA to ADDRD) ............................................. 13.2.2 A/D Control/Status Register (ADCSR) ............................................................... 13.2.3 A/D Control Register (ADCR) ............................................................................ 13.3 CPU Interface.................................................................................................................... 13.4 Operation .......................................................................................................................... 13.4.1 Single Mode (SCAN = 0) .................................................................................... 13.4.2 Scan Mode (SCAN = 1)....................................................................................... 13.4.3 Input Sampling and A/D Conversion Time ......................................................... 13.4.4 External Trigger Input Timing............................................................................. 13.5 Interrupts........................................................................................................................... 13.6 Usage Notes ...................................................................................................................... 419 419 420 421 422 423 423 424 427 428 429 429 431 433 434 435 435
Section 14 RAM .................................................................................................................. 441
14.1 Overview........................................................................................................................... 14.1.1 Block Diagram..................................................................................................... 14.1.2 Register Configuration......................................................................................... 14.2 System Control Register (SYSCR) ................................................................................... 14.3 Operation .......................................................................................................................... 441 442 442 443 444
Section 15 ROM .................................................................................................................. 445
15.1 Features............................................................................................................................. 445 15.2 Overview........................................................................................................................... 446 15.2.1 Block Diagram..................................................................................................... 446 15.2.2 Mode Transitions ................................................................................................. 447 15.2.3 On-Board Programming Modes........................................................................... 449 15.2.4 Flash Memory Emulation in RAM ...................................................................... 451 15.2.5 Differences between Boot Mode and User Program Mode ................................. 452 15.2.6 Block Configuration ............................................................................................ 453 15.3 Pin Configuration.............................................................................................................. 454 15.4 Register Configuration...................................................................................................... 454 15.5 Register Descriptions ........................................................................................................ 455 15.5.1 Flash Memory Control Register 1 (FLMCR1)..................................................... 455
Rev.2.00 Mar. 22, 2007 Page xx of xxiv REJ09B0352-0200
15.6
15.7
15.8
15.9 15.10
15.11 15.12 15.13 15.14
15.5.2 Flash Memory Control Register 2 (FLMCR2)..................................................... 15.5.3 Erase Block Register 1 (EBR1)............................................................................ 15.5.4 Erase Block Register 2 (EBR2)............................................................................ 15.5.5 RAM Emulation Register (RAMER)................................................................... 15.5.6 Differences from H8/3039 F-ZTAT Group ......................................................... On-Board Programming Modes ........................................................................................ 15.6.1 Boot Mode ........................................................................................................... 15.6.2 User Program Mode............................................................................................. Programming/Erasing Flash Memory ............................................................................... 15.7.1 Program Mode ..................................................................................................... 15.7.2 Program-Verify Mode.......................................................................................... 15.7.3 Notes on Program/Program-Verify Procedure..................................................... 15.7.4 Erase Mode .......................................................................................................... 15.7.5 Erase-Verify Mode............................................................................................... Protection .......................................................................................................................... 15.8.1 Hardware Protection ............................................................................................ 15.8.2 Software Protection.............................................................................................. 15.8.3 Error Protection.................................................................................................... 15.8.4 NMI Input Disable Conditions............................................................................. Flash Memory Emulation in RAM.................................................................................... Flash Memory PROM Mode............................................................................................. 15.10.1 Socket Adapters and Memory Map...................................................................... 15.10.2 Notes on Use of PROM Mode ............................................................................. Notes on Flash Memory Programming/Erasing................................................................ Overview of Mask ROM................................................................................................... 15.12.1 Block Diagram ..................................................................................................... Notes on Ordering Mask ROM Version Chips ................................................................. Notes when Converting the F-ZTAT Application Software to the Mask-ROM Versions ............................................................................................................................
458 459 460 461 463 464 465 470 472 473 474 474 479 479 481 481 483 484 486 488 490 490 491 492 498 498 499 500
Section 16 Clock Pulse Generator .................................................................................. 501
16.1 Overview........................................................................................................................... 16.1.1 Block Diagram ..................................................................................................... 16.2 Oscillator Circuit............................................................................................................... 16.2.1 Connecting a Crystal Resonator........................................................................... 16.2.2 External Clock Input ............................................................................................ 16.3 Duty Adjustment Circuit ................................................................................................... 16.4 Prescalers .......................................................................................................................... 16.5 Frequency Divider............................................................................................................. 16.5.1 Register Configuration......................................................................................... 16.5.2 Division Control Register (DIVCR) .................................................................... 501 502 503 503 505 508 508 508 508 508
Rev.2.00 Mar. 22, 2007 Page xxi of xxiv REJ09B0352-0200
16.5.3 Usage Notes ......................................................................................................... 509
Section 17 Power-Down State ......................................................................................... 511
17.1 Overview........................................................................................................................... 511 17.2 Register Configuration...................................................................................................... 513 17.2.1 System Control Register (SYSCR) ...................................................................... 513 17.2.2 Module Standby Control Register (MSTCR) ...................................................... 515 17.3 Sleep Mode ....................................................................................................................... 517 17.3.1 Transition to Sleep Mode..................................................................................... 517 17.3.2 Exit from Sleep Mode.......................................................................................... 517 17.4 Software Standby Mode.................................................................................................... 518 17.4.1 Transition to Software Standby Mode ................................................................. 518 17.4.2 Exit from Software Standby Mode ...................................................................... 518 17.4.3 Selection of Oscillator Waiting Time after Exit from Software Standby Mode .. 519 17.4.4 Sample Application of Software Standby Mode.................................................. 520 17.4.5 Usage Note........................................................................................................... 520 17.5 Hardware Standby Mode .................................................................................................. 521 17.5.1 Transition to Hardware Standby Mode................................................................ 521 17.5.2 Exit from Hardware Standby Mode ..................................................................... 521 17.5.3 Timing for Hardware Standby Mode ................................................................... 521 17.6 Module Standby Function................................................................................................. 523 17.6.1 Module Standby Timing ...................................................................................... 523 17.6.2 Read/Write in Module Standby............................................................................ 523 17.6.3 Usage Notes ......................................................................................................... 523 17.7 System Clock Output Disabling Function......................................................................... 524
Section 18 Electrical Characteristics ............................................................................. 525
18.1 Electrical characteristics of Mask ROM Version.............................................................. 18.1.1 Absolute Maximum Ratings ................................................................................ 18.1.2 DC Characteristics ............................................................................................... 18.1.3 AC Characteristics ............................................................................................... 18.1.4 A/D Conversion Characteristics........................................................................... 18.2 Electrical characteristics of Flash Memory Version ......................................................... 18.2.1 Absolute Maximum Ratings ................................................................................ 18.2.2 DC Characteristics ............................................................................................... 18.2.3 AC Characteristics ............................................................................................... 18.2.4 A/D Conversion Characteristics........................................................................... 18.2.5 Flash Memory Characteristics ............................................................................. 18.3 Operational Timing........................................................................................................... 18.3.1 Bus Timing .......................................................................................................... 18.3.2 Control Signal Timing .........................................................................................
Rev.2.00 Mar. 22, 2007 Page xxii of xxiv REJ09B0352-0200
525 525 526 530 535 536 536 537 541 546 547 549 549 553
18.3.3 18.3.4 18.3.5 18.3.6
Clock Timing ....................................................................................................... TPC and I/O Port Timing..................................................................................... ITU Timing .......................................................................................................... SCI Input/Output Timing .....................................................................................
555 555 556 557
Appendix A Instruction Set .............................................................................................. 559
A.1 A.2 A.3 Instruction List .................................................................................................................. 559 Operation Code Maps ....................................................................................................... 574 Number of States Required for Execution ........................................................................ 577
Appendix B Internal I/O Register Field ........................................................................ 589
B.1 B.2 Addresses .......................................................................................................................... 589 Function ............................................................................................................................ 596
Appendix C I/O Block Diagrams.................................................................................... 655
C.1 C.2 C.3 C.4 C.5 C.6 C.7 C.8 C.9 C.10 Port 1 Block Diagram ....................................................................................................... Port 2 Block Diagram ....................................................................................................... Port 3 Block Diagram ....................................................................................................... Port 5 Block Diagram ....................................................................................................... Port 6 Block Diagrams...................................................................................................... Port 7 Block Diagram ....................................................................................................... Port 8 Block Diagrams...................................................................................................... Port 9 Block Diagrams...................................................................................................... Port A Block Diagrams ..................................................................................................... Port B Block Diagrams ..................................................................................................... 655 656 657 658 659 661 662 664 668 671
Appendix D Pin States ....................................................................................................... 674
D.1 D.2 Port States in Each Mode .................................................................................................. 674 Pin States at Reset ............................................................................................................. 676
Appendix E Timing of Transition to and Recovery from Hardware Standby Mode................................................................................................................ 679 Appendix F Product Lineup ............................................................................................. 680 Appendix G Package Dimensions .................................................................................. 681 Appendix H Comparison of H8/300H Series Product Specifications.................. 683
H.1 Differences between H8/3039F and H8/3022F................................................................. 683
Rev.2.00 Mar. 22, 2007 Page xxiii of xxiv REJ09B0352-0200
Rev.2.00 Mar. 22, 2007 Page xxiv of xxiv REJ09B0352-0200
1. Overview
Section 1 Overview
1.1 Overview
The H8/3022 Group comprises microcomputers (MCUs) that integrate system supporting functions together with an H8/300H CPU core featuring an original Renesas Technology architecture. The H8/300H CPU has a 32-bit internal architecture with sixteen 16-bit general registers, and a concise, optimized instruction set designed for speed. It can address a 16-Mbyte linear address space. Its instruction set is upward-compatible at the object-code level with the H8/300 CPU, enabling easy porting of software from the H8/300 Series. The on-chip system supporting functions include ROM, RAM, a 16-bit integrated timer unit (ITU), a programmable timing pattern controller (TPC), a watchdog timer (WDT), a serial communication interface (SCI), an A/D converter, I/O ports, and other facilities. The H8/3022 Group consists of four models: the H8/3022 with 256 kbytes of ROM and 8 kbytes of RAM, the H8/3021 with 192 kbytes of ROM and 8 kbytes of RAM, and the H8/3020 with 128 kbytes of ROM and 4 kbytes of RAM. The five MCU operating modes offer a choice of expanded mode, single-chip mode and address space size. In addition to the masked-ROM version of the H8/3022 Group, an F-ZTAT* version with an onchip flash memory that can be freely programmed and reprogrammed by the user after the board is installed is also available. This version enables users to respond quickly and flexibly to changing application specifications, growing production volumes, and other conditions. Table 1.1 summarizes the features of the H8/3022 Group. Note: * F-ZTAT (Flexible ZTAT) is a trademark of Renesas Technology Corp.
Rev.2.00 Mar. 22, 2007 Page 1 of 684 REJ09B0352-0200
1. Overview
Table 1.1
Feature CPU
Features
Description Upward-compatible with the H8/300 CPU at the object-code level General-register machine * Sixteen 16-bit general registers (also useable as sixteen 8-bit registers or eight 32-bit registers) Maximum clock rate: 18 MHz Add/subtract: 111 ns Multiply/divide: 778 ns Normal mode (64-kbyte address space)* Advanced mode (16-Mbyte address space) 8/16/32-bit data transfer, arithmetic, and logic instructions Signed and unsigned multiply instructions (8 bits x 8 bits, 16 bits x 16 bits) Signed and unsigned divide instructions (16 bits / 8 bits, 32 bits / 16 bits) Bit accumulator function Bit manipulation instructions with register-indirect specification of bit positions ROM: 256 kbytes RAM: 8 kbytes ROM: 192 kbytes RAM: 8 kbytes ROM: 128 kbytes RAM: 4 kbytes Five external interrupt pins: NMI, IRQ0, IRQ1, IRQ4, IRQ5 25 internal interrupts Three selectable interrupt priority levels
High-speed operation * * * * * * * * * * Memory
Two CPU operating modes
Instruction features
H8/3022 * * * * * *
H8/3021
H8/3020
Interrupt controller
* * *
Rev.2.00 Mar. 22, 2007 Page 2 of 684 REJ09B0352-0200
1. Overview Feature Bus controller Description * * * 16-bit integrated timer unit (ITU) * * * * * * * * * Programmable timing pattern controller (TPC) * * * Watchdog timer * (WDT), 1 channel * * Serial communication interface (SCI), 2 channels A/D converter * * * * * * * * * I/O ports * * Address space can be partitioned into eight areas, with independent bus specifications in each area Two-state or three-state access selectable for each area Selection of four wait modes Five 16-bit timer channels, capable of processing up to 12 pulse outputs or 10 pulse inputs 16-bit timer counter (channels 0 to 4) Two multiplexed output compare/input capture pins (channels 0 to 4) Operation can be synchronized (channels 0 to 4) PWM mode available (channels 0 to 4) Phase counting mode available (channel 2) Buffering available (channels 3 and 4) Reset-synchronized PWM mode available (channels 3 and 4) Complementary PWM mode available (channels 3 and 4) Maximum 15-bit pulse output, using ITU as time base Up to three 4-bit pulse output groups and one 3-bit pulse output group (or one 15-bit group, one 8-bit group, or one 7-bit group) Non-overlap mode available Reset signal can be generated by overflow Reset signal can be output externally (However, not available with the FZTAT version.) Usable as an interval timer Selection of asynchronous or synchronous mode Full duplex: can transmit and receive simultaneously On-chip baud-rate generator Smart card interface functions added (SCI0 only) Resolution: 10 bits Eight channels, with selection of single or scan mode Variable analog conversion voltage range Sample-and-hold function Can be externally triggered 55 input/output pins 8 input-only pins
Rev.2.00 Mar. 22, 2007 Page 3 of 684 REJ09B0352-0200
1. Overview Feature Operating modes Description Five MCU operating modes Mode Mode 1 Mode 3 Mode 5 Mode 6 Mode 7 * Power-down state * * * * * Other features Product lineup * Address Space 1 Mbyte 16 Mbytes 1 Mbyte 16 Mbytes 1 Mbyte Address Pins A0 to A19 A0 to A23 A0 to A19 A0 to A23 -- Bus Width 8 bits 8 bits 8 bits 8 bits --
On-chip ROM is disabled in modes 1 and 3 Sleep mode Software standby mode Hardware standby mode Module standby function Programmable System clock frequency division On-chip clock oscillator Model (3V) HD64F3022F HD64F3022TE HD6433022F HD6433022TE HD6433021F HD6433021TE HD6433020F HD6433020TE Package 80-pin QFP (FP-80A) 80-pin TQFP (TFP-80C) 80-pin QFP (FP-80A) 80-pin TQFP (TFP-80C) 80-pin QFP (FP-80A) 80-pin TQFP (TFP-80C) 80-pin QFP (FP-80A) 80-pin TQFP (TFP-80C) Mask ROM Mask ROM Mask ROM ROM Flash memory
Note:
*
Normal mode cannot be used with this LSI.
Rev.2.00 Mar. 22, 2007 Page 4 of 684 REJ09B0352-0200
1. Overview
1.2
Block Diagram
Figure 1.1 shows an internal block diagram of the H8/3022 Group.
P37/D7 P36/D6 P35/D5 P34/D4 P33/D3 P32/D2 P31/D1 P30/D0
VCC VCC VSS VSS VSS
Port 3 Address bus MD2 MD1 MD0 EXTAL XTAL STBY RES RESO/FWE* NMI Data bus (upper) Data bus (lower)
Clock osc. Bus controller Port 5 Port 2 Port 1
H8/300H CPU
P53/A19 P52/A18 P51/A17 P50/A16
P65/WR P64/RD P63/AS P60/WAIT
Port 6
ROM (Flash memory, masked ROM)
Interrupt controller
P27/A15 P26/A14 P25/A13 P24/A12 P23/A11 P22/A10 P21/A9 P20/A8 P17/A7 P16/A6 P15/A5 P14/A4 P13/A3 P12/A2 P11/A1 P10/A0
RAM
Watchdog timer (WDT) Serial communication interface (SCI) x 2 channel
P81/IRQ1 P80/IRQ0
16-bit integrated timer unit (ITU)
Port 8
Port B
PB7/TP15/ADTRG PB5/TP13/TOCXB4 PB4/TP12/TOCXA4 PB3/TP11/TIOCB4 PB2/TP10/TIOCA4 PB1/TP9/TIOCB3 PB0/TP8/TIOCA3
Port A
PA7/TP7/TIOCB2/A20 PA6/TP6/TIOCA2/A21 PA5/TP5/TIOCB1/A22 PA4/TP4/TIOCA1/A23 PA3/TP3/TIOCB0/TCLKD PA2/TP2/TIOCA0/TCLKC PA1/TP1/TCLKB PA0/TP0/TCLKA AVCC AVSS
Port 7
P77/AN7 P76/AN6 P75/AN5 P74/AN4 P73/AN3 P72/AN2 P71/AN1 P70/AN0
Note: * Masked ROM : RESO Flash memory: FWE
Figure 1.1 Block Diagram
Rev.2.00 Mar. 22, 2007 Page 5 of 684 REJ09B0352-0200
Port 9
Programmable timing pattern controller (TPC)
A/D converter
P95/SCK1/IRQ5 P94/SCK0/IRQ4 P93/RxD1 P92/RxD0 P91/TxD1 P90/TxD0
1. Overview
1.3
1.3.1
Pin Description
Pin Arrangement
Figure 1.2 shows the pin arrangement of the H8/3022 Group.
RESO/FWE*
P60/WAIT
P71/AN1
P70/AN0
P65/WR
P53/A19 42
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
P72/AN2 P73/AN3 P74/AN4 P75/AN5 P76/AN6 P77/AN7 AVCC P80/IRQ0 P81/IRQ1 P91/TxD1 P93/RxD1 P95/SCK1/IRQ5 PA0/TP0/TCLKA PA1/TP1/TCLKB PA2/TP2/TIOCA0/TCLKC PA3/TP3/TIOCB0/TCLKD PA4/TP4/TIOCA1/A23 PA5/TP5/TIOCB1/A22 PA6/TP6/TIOCA2/A21 PA7/TP7/TIOCB2/A20
41
P52/A18
P64/RD
P63/AS
EXTAL
STBY
XTAL
AVSS
RES
MD1
MD0
NMI
VCC
VSS
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
12 13 14 15 16 18 19 20 10 11 17 1 2 3 4 5 6 7 8 9
40 39 38 37 36 35 34 33 Top view (FP-80A, TFP-80C) 32 31 30 29 28 27 26 25 24 23 22 21
A17/P51 A16/P50 A15/P27 A14/P26 A13/P25 A12/P24 A11/P23 A10/P22 A9/P21 A8/P20 VSS A7/P17 A6/P16 A5/P15 A4/P14 A3/P13 A2/P12 A1/P11 A0/P10 VCC
TIOCA3/TP8/PB0
TIOCB3/TP9/PB1
TIOCA4/TP10/PB2
TIOCB4/TP11/PB3
TOCXA4/TP12/PB4
TOCXB4/TP13/PB5
MD2
ADTRG/TP15/PB7
TxD0/P90
RxD0/P92
IRQ4/SCK0/P94
D0/P30
D1/P31
D2/P32
D3/P33
D4/P34
D5/P35
D6/P36
Note: * Masked ROM: RESO Flash memory: FWE
Figure 1.2 Pin Arrangement (FP-80A, TFP-80C Top View)
Rev.2.00 Mar. 22, 2007 Page 6 of 684 REJ09B0352-0200
D7/P37
VSS
1. Overview
1.3.2
Pin Functions
Pin Assignments in Each Mode: Table 1.2 lists the FP-80A and TFP-80C pin assignments in each mode. Table 1.2 FP-80A and TFP-80C Pin Assignments in Each Mode
Pin Name Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Mode 1 PB0/TP8/ TIOCA3 PB1/TP9/ TIOCB3 PB2/TP10/ TIOCA4 PB3/TP11/ TIOCB4 PB4/TP12/ TOCXA4 PB5/TP13/ TOCXB4 MD2 PB7/TP15/ ADTRG P90/TxD0 P92/RxD0 P94/SCK0/ IRQ4 VSS D0 D1 D2 D3 D4 D5 D6 D7 Mode 3 PB0/TP8/ TIOCA3 PB1/TP9/ TIOCB3 PB2/TP10/ TIOCA4 PB3/TP11/ TIOCB4 PB4/TP12/ TOCXA4 PB5/TP13/ TOCXB4 MD2 PB7/TP15/ ADTRG P90/TxD0 P92/RxD0 P94/SCK0/ IRQ4 VSS D0 D1 D2 D3 D4 D5 D6 D7 Mode 5 PB0/TP8/ TIOCA3 PB1/TP9/ TIOCB3 PB2/TP10/ TIOCA4 PB3/TP11/ TIOCB4 PB4/TP12/ TOCXA4 PB5/TP13/ TOCXB4 MD2 PB7/TP15/ ADTRG P90/TxD0 P92/RxD0 P94/SCK0/ IRQ4 VSS D0 D1 D2 D3 D4 D5 D6 D7 Mode 6 PB0/TP8/ TIOCA3 PB1/TP9/ TIOCB3 PB2/TP10/ TIOCA4 PB3/TP11/ TIOCB4 PB4/TP12/ TOCXA4 PB5/TP13/ TOCXB4 MD2 PB7/TP15/ ADTRG P90/TxD0 P92/RxD0 P94/SCK0/ IRQ4 VSS D0 D1 D2 D3 D4 D5 D6 D7 Mode 7 PB0/TP8/ TIOCA3 PB1/TP9/ TIOCB3 PB2/TP10/ TIOCA4 PB3/TP11/ TIOCB4 PB4/TP12/ TOCXA4 PB5/TP13/ TOCXB4 MD2 PB7/TP15/ ADTRG P90/TxD0 P92/RxD0 P94/SCK0/ IRQ4 VSS P30 P31 P32 P33 P34 P35 P36 P37
Rev.2.00 Mar. 22, 2007 Page 7 of 684 REJ09B0352-0200
1. Overview Pin Name Pin No. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Mode 1 VCC A0 A1 A2 A3 A4 A5 A6 A7 VSS A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 P60/WAIT MD0 MD1 STBY RES NMI VSS Mode 3 VCC A0 A1 A2 A3 A4 A5 A6 A7 VSS A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 P60/WAIT MD0 MD1 STBY RES NMI VSS Mode 5 VCC P10/A0 P11/A1 P12/A2 P13/A3 P14/A4 P15/A5 P16/A6 P17/A7 VSS P20/A8 P21/A9 P22/A10 P23/A11 P24/A12 P25/A13 P26/A14 P27/A15 P50/A16 P51/A17 P52/A18 P53/A19 P60/WAIT MD0 MD1 STBY RES NMI VSS Mode 6 VCC P10/A0 P11/A1 P12/A2 P13/A3 P14/A4 P15/A5 P16/A6 P17/A7 VSS P20/A8 P21/A9 P22/A10 P23/A11 P24/A12 P25/A13 P26/A14 P27/A15 P50/A16 P51/A17 P52/A18 P53/A19 P60/WAIT MD0 MD1 STBY RES NMI VSS Mode 7 VCC P10 P11 P12 P13 P14 P15 P16 P17 VSS P20 P21 P22 P23 P24 P25 P26 P27 P50 P51 P52 P53 P60 MD0 MD1 STBY RES NMI VSS
Rev.2.00 Mar. 22, 2007 Page 8 of 684 REJ09B0352-0200
1. Overview Pin Name Pin No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 Mode 1 EXTAL XTAL VCC AS RD WR RESO/ FWE* AVSS P70/AN0 P71/AN1 P72/AN2 P73/AN3 P74/AN4 P75/AN5 P76/AN6 P77/AN7 AVCC P80/IRQ0 P81/IRQ1 P91/TxD1 P93/RxD1 P95/SCK1/ IRQ5 PA0/TP0/ TCLKA PA1/TP1/ TCLKB PA2/TP2/ TIOCA0/ TCLKC Mode 3 EXTAL XTAL VCC AS RD WR RESO/ FWE* AVSS P70/AN0 P71/AN1 P72/AN2 P73/AN3 P74/AN4 P75/AN5 P76/AN6 P77/AN7 AVCC P80/IRQ0 P81/IRQ1 P91/TxD1 P93/RxD1 P95/SCK1/ IRQ5 PA0/TP0/ TCLKA PA1/TP1/ TCLKB PA2/TP2/ TIOCA0/ TCLKC Mode 5 EXTAL XTAL VCC AS RD WR RESO/ FWE* AVSS P70/AN0 P71/AN1 P72/AN2 P73/AN3 P74/AN4 P75/AN5 P76/AN6 P77/AN7 AVCC P80/IRQ0 P81/IRQ1 P91/TxD1 P93/RxD1 P95/SCK1/ IRQ5 PA0/TP0/ TCLKA PA1/TP1/ TCLKB PA2/TP2/ TIOCA0/ TCLKC Mode 6 EXTAL XTAL VCC AS RD WR RESO/ FWE* AVSS P70/AN0 P71/AN1 P72/AN2 P73/AN3 P74/AN4 P75/AN5 P76/AN6 P77/AN7 AVCC P80/IRQ0 P81/IRQ1 P91/TxD1 P93/RxD1 P95/SCK1/ IRQ5 PA0/TP0/ TCLKA PA1/TP1/ TCLKB PA2/TP2/ TIOCA0/ TCLKC Mode 7 EXTAL XTAL VCC P63 P64 P65 RESO/ FWE* AVSS P70/AN0 P71/AN1 P72/AN2 P73/AN3 P74/AN4 P75/AN5 P76/AN6 P77/AN7 AVCC P80/IRQ0 P81/IRQ1 P91/TxD1 P93/RxD1 P95/SCK1/ IRQ5 PA0/TP0/ TCLKA PA1/TP1/ TCLKB PA2/TP2/ TIOCA0/ TCLKC
Rev.2.00 Mar. 22, 2007 Page 9 of 684 REJ09B0352-0200
1. Overview Pin Name Pin No. 76 Mode 1 PA3/TP3/ TIOCB0/ TCLKD PA4/TP4/ TIOCA1 PA5/TP5/ TIOCB1 PA6/TP6/ TIOCA2 PA7/TP7/ TIOCB2 Mode 3 PA3/TP3/ TIOCB0/ TCLKD PA4/TP4/ TIOCA1/A23 PA5/TP5/ TIOCB1/A22 PA6/TP6/ TIOCA2/A21 A20 Mode 5 PA3/TP3/ TIOCB0/ TCLKD PA4/TP4/ TIOCA1 PA5/TP5/ TIOCB1 PA6/TP6/ TIOCA2 PA7/TP7/ TIOCB2 Mode 6 PA3/TP3/ TIOCB0/ TCLKD PA4/TP4/ TIOCA1/A23 PA5/TP5/ TIOCB1/A22 PA6/TP6/ TIOCA2/A21 A20 Mode 7 PA3/TP3/ TIOCB0/ TCLKD PA4/TP4/ TIOCA1 PA5/TP5/ TIOCB1 PA6/TP6/ TIOCA2 PA7/TP7/ TIOCB2
77 78 79 80
Notes: Pins marked NC should be left unconnected. * Mask ROM: RESO Flash Memory: FWE
Rev.2.00 Mar. 22, 2007 Page 10 of 684 REJ09B0352-0200
1. Overview
1.4
Pin Functions
Table 1.3 summarizes the pin functions. Table 1.3
Type Power
Pin Functions
Symbol VCC Pin No. 21, 53 12, 30, 50 52 I/O Input Name and Function Power: For connection to the power supply. Connect all VCC pins to the system power supply. Ground: For connection to ground (0 V). Connect all VSS pins to the 0-V system power supply. For connection to a crystal resonator For examples of crystal resonator and external clock input, see section 16, Clock Pulse Generator. For connection to a crystal resonator or input of an external clock signal. For examples of crystal resonator and external clock input, see section 16, Clock Pulse Generator. System clock: Supplies the system clock to external devices Mode 2 to mode 0: For setting the operating mode, as follows. These pins should not be changed during operation. MD2 0 0 0 0 1 1 1 1 MD1 0 0 1 1 0 0 1 1 MD0 0 1 0 1 0 1 0 1 Operating Mode -- Mode 1 -- Mode 3 -- Mode 5 Mode 6 Mode 7
VSS
Input
Clock
XTAL
Input
EXTAL
51
Input
Operating mode control MD2, MD1, MD0
46 7, 45, 44
Output Input
Rev.2.00 Mar. 22, 2007 Page 11 of 684 REJ09B0352-0200
1. Overview Type System control Symbol RES RESO/ FWE Pin No. 48 57 I/O Input Output/ Input Name and Function Reset input: When driven low, this pin resets the chip Reset output (Mask ROM version): Outputs WDT-generated reset signal to an external device. Write enable signal (F-ZTAT version): Flash memory write control signal. Standby: When driven low, this pin forces a transition to hardware standby mode Nonmaskable interrupt: Requests a nonmaskable interrupt Interrupt request 5, 4, 1, 0: Maskable interrupt request pins Address bus: Outputs address signals
STBY Interrupts NMI IRQ5, IRQ4 IRQ1, IRQ0 Address bus A23 to A20, A19 to A8, A7 to A0 Data bus Bus control D7 to D0 AS RD WR
47 49 72, 11, 69, 68 77 to 80, 42 to 31, 29 to 22 20 to 13 54 55 56
Input Input Input Output
Input/ output Output Output Output
Data bus: Bidirectional data bus Address strobe: Goes low to indicate valid address output on the address bus Read: Goes low to indicate reading from the external address space. Write: Goes low to indicate writing to the external address space indicates valid data on the data bus. Wait: Requests insertion of wait states in bus cycles during access to the external address space
WAIT
43
Input
Rev.2.00 Mar. 22, 2007 Page 12 of 684 REJ09B0352-0200
1. Overview Type 16-bit integrated timer unit (ITU) Symbol TCLKD to TCLKA TIOCA4 to TIOCA0 TIOCB4 to TIOCB0 TOCXA4 TOCXB4 Programmable timing pattern controller (TPC) Serial communication interface (SCI) TP15, TP13 to TP0 Pin No. 76 to 73 3, 1, 79, 77, 75 4, 2, 80, 78, 76 5 6 8, 6 to 1 80 to 73 I/O Input Input/ Output Input/ output Output Output Output Name and Function Clock input D to A: External clock inputs Input capture/output compare A4 to A0: GRA4 to GRA0 output compare or input capture, or PWM output Input capture/output compare B4 to B0 GRB4 to GRB0 output compare or input capture, or PWM output Output compare XA4: PWM output Output compare XB4: PWM output TPC output 15, 13 to 0 : Pulse output
TxD1, TxD0 RxD1, RxD0 SCK1, SCK0
70, 9 71, 10 72, 11 66 to 59 8 67
Output Input Input/ output Input Input Input
Transmit data:(channels 0 and 1): SCI data output Receive data:(channels 0 and 1): SCI data input Serial clock:(channels 0 and 1): SCI clock input/output Analog 7 to 0: Analog input pins A/D trigger: External trigger input for starting A/D conversion Power supply pin and reference voltage input pin for the A/D converter. Connect to the system power supply when not using the A/D converter Ground pin for the A/D converter. Connect to system power-supply (0 V).
A/D converter AN7 to AN0 ADTRG AVCC
AVSS
58
Input
Rev.2.00 Mar. 22, 2007 Page 13 of 684 REJ09B0352-0200
1. Overview Type I/O ports Symbol P17 to P10 Pin No. 29 to 22 I/O Input/ output Input/ output Input/ output Input/ output Input/ output Input Input/ output Input/ output Input/ output Input/ output Name and Function Port 1: Eight input/output pins. The direction of each pin can be selected in the port 1 data direction register (P1DDR). Port 2: Eight input/output pins. The direction of each pin can be selected in the port 2 data direction register (P2DDR). Port 3: Eight input/output pins. The direction of each pin can be selected in the port 3 data direction register (P3DDR). Port 5: Four input/output pins. The direction of each pin can be selected in the port 5 data direction register (P5DDR). Port 6: Four input/output pins. The direction of each pin can be selected in the port 6 data direction register (P6DDR). Port 7: Eight input pins Port 8: Two input/output pins. The direction of each pin can be selected in the port 8 data direction register (P8DDR). Port 9: Six input/output pins. The direction of each pin can be selected in the port 9 data direction register (P9DDR). Port A: Eight input/output pins. The direction of each pin can be selected in the port A data direction register (PADDR). Port B: Seven input/output pins. The direction of each pin can be selected in the port B data direction register (PBDDR).
P27 to P20
38 to 31
P37 to P30
20 to 13
P53 to P50
42 to 39
P65 to P63, 56 to 54, P60 43 P77 to P70 P81, P80 66 to 59 69, 68
P95 to P90
72, 11 71, 10 70, 9
PA7 to PA0 80 to 73
PB7, PB5 to PB0
8, 6 to 1
Rev.2.00 Mar. 22, 2007 Page 14 of 684 REJ09B0352-0200
2. CPU
Section 2 CPU
2.1 Overview
The H8/300H CPU is a high-speed central processing unit with an internal 32-bit architecture that is upward-compatible with the H8/300 CPU. The H8/300H CPU has sixteen 16-bit general registers, can address a 16-Mbyte linear address space, and is ideal for realtime control. 2.1.1 Features
The H8/300H CPU has the following features. * Upward compatibility with H8/300 CPU Can execute H8/300 series object programs without alteration * General-register architecture Sixteen 16-bit general registers (also usable as sixteen 8-bit registers or eight 32-bit registers) * Sixty-two basic instructions 8/16/32-bit transfer, arithmetic and logic instructions Multiply and divide instructions Powerful bit-manipulation instructions * Eight addressing modes Register direct [Rn] Register indirect [@ERn] Register indirect with displacement [@(d:16, ERn) or @(d:24, ERn)] Register indirect with post-increment or pre-decrement [@ERn+ or @-ERn] Absolute address [@aa:8, @aa:16, or @aa:24] Immediate [#xx:8, #xx:16, or #xx:32] Program-counter relative [@(d:8, PC) or @(d:16, PC)] Memory indirect [@@aa:8] * 16-Mbyte linear address space
Rev.2.00 Mar. 22, 2007 Page 15 of 684 REJ09B0352-0200
2. CPU
* High-speed operation All frequently-used instructions execute in two to four states Maximum clock frequency: 18 MHz 8/16/32-bit register-register add/subtract: 8 x 8-bit register-register multiply: 16 / 8-bit register-register divide: 32 / 16-bit register-register divide: * Two CPU operating modes Normal mode (cannot be used with this LSI) Advanced mode * Low-power mode Transition to power-down state by SLEEP instruction 2.1.2 Differences from H8/300 CPU 778 ns 778 ns 1222 ns 111 ns
16 x 16-bit register-register multiply: 1222 ns
In comparison to the H8/300 CPU, the H8/300H has the following enhancements. * More general registers Eight 16-bit registers have been added. * Expanded address space Advanced mode supports a maximum 16-Mbyte address space. Normal mode supports the same 64-kbyte address space as the H8/300 CPU. * Enhanced addressing The addressing modes have been enhanced to make effective use of the 16-Mbyte address space. * Enhanced instructions Data transfer, arithmetic, and logic instructions can operate on 32-bit data. Signed multiply/divide instructions and other instructions have been added.
Rev.2.00 Mar. 22, 2007 Page 16 of 684 REJ09B0352-0200
2. CPU
2.2
CPU Operating Modes
The H8/300H CPU has two operating modes: normal and advanced. Normal mode supports a maximum 64-kbyte address space. Advanced mode supports up to 16 Mbytes. See figure 2.1. Unless specified otherwise, all descriptions in this manual refer to advanced mode.
Maximum 64 kbytes, program and data areas combined
Normal mode*
CPU operating modes Maximum 16 Mbytes, program and data areas combined
Advanced mode
Note: * Normal mode cannot be used with this LSI.
Figure 2.1 CPU Operating Modes
Rev.2.00 Mar. 22, 2007 Page 17 of 684 REJ09B0352-0200
2. CPU
2.3
Address Space
The maximum address space of the H8/300H CPU is 16 Mbytes. This LSI allows selection of a normal mode and advanced mode 1-Mbyte mode or 16-Mbyte mode for the address space depending on the MCU operation mode. Figure 2.2 shows the address ranges of the H8/3022 Group. For further details see section 3.6, Memory Map in Each Operating Mode. The 1-Mbyte operating mode uses 20-bit addressing. The upper 4 bits of effective addresses are ignored.
H'0000 H'00000 H'000000
H'FFFF H'FFFFF
H'FFFFFF (a) 1-Mbyte mode 1. Normal mode (64-Kbyte mode)* Note: * Normal mode cannot be used with this LSI. 2. Advanced mode (b) 16-Mbyte mode
Figure 2.2 Memory Map
Rev.2.00 Mar. 22, 2007 Page 18 of 684 REJ09B0352-0200
2. CPU
2.4
2.4.1
Register Configuration
Overview
The H8/300H CPU has the internal registers shown in figure 2.3. There are two types of registers: general registers and control registers.
General Registers (ERn) 15 ER0 ER1 ER2 ER3 ER4 ER5 ER6 ER7 Control Registers (CR) 23 PC 76543210 CCR I UI H U N Z V C Legend SP: Stack pointer PC: Program counter CCR: Condition code register Interrupt mask bit I: User bit or interrupt mask bit UI: Half-carry flag H: User bit U: Negative flag N: Zero flag Z: Overflow flag V: Carry flag C: 0 E0 E1 E2 E3 E4 E5 E6 E7 (SP) 07 R0H R1H R2H R3H R4H R5H R6H R7H 07 R0L R1L R2L R3L R4L R5L R6L R7L 0
Figure 2.3 CPU Registers
Rev.2.00 Mar. 22, 2007 Page 19 of 684 REJ09B0352-0200
2. CPU
2.4.2
General Registers
The H8/300H CPU has eight 32-bit general registers. These general registers are all functionally alike and can be used without distinction between data registers and address registers. When a general register is used as a data register, it can be accessed as a 32-bit, 16-bit, or 8-bit register. When the general registers are used as 32-bit registers or as address registers, they are designated by the letters ER (ER0 to ER7). The ER registers divide into 16-bit general registers designated by the letters E (E0 to E7) and R (R0 to R7). These registers are functionally equivalent, providing a maximum sixteen 16-bit registers. The E registers (E0 to E7) are also referred to as extended registers. The R registers divide into 8-bit general registers designated by the letters RH (R0H to R7H) and RL (R0L to R7L). These registers are functionally equivalent, providing a maximum sixteen 8-bit registers. Figure 2.4 illustrates the usage of the general registers. The usage of each register can be selected independently.
* Address registers * 32-bit registers
* 16-bit registers E registers (extended registers) E0 to E7
* 8-bit registers
ER registers ER0 to ER7 R registers R0 to R7
RH registers R0H to R7H
RL registers R0L to R7L
Figure 2.4 Usage of General Registers
Rev.2.00 Mar. 22, 2007 Page 20 of 684 REJ09B0352-0200
2. CPU
General register ER7 has the function of stack pointer (SP) in addition to its general-register function, and is used implicitly in exception handling and subroutine calls. Figure 2.5 shows the stack.
Free area SP (ER7) Stack area
Figure 2.5 Stack 2.4.3 Control Registers
The control registers are the 24-bit program counter (PC) and the 8-bit condition code register (CCR). Program Counter (PC): This 24-bit counter indicates the address of the next instruction the CPU will execute. The length of all CPU instructions is 2 bytes (one word) or a multiple of 2 bytes, so the least significant PC bit is ignored. When an instruction is fetched, the least significant PC bit is regarded as 0. Condition Code Register (CCR): This 8-bit register contains internal CPU status information, including the interrupt mask bit (I) and half-carry (H), negative (N), zero (Z), overflow (V), and carry (C) flags. Bit 7--Interrupt Mask Bit (I): Masks interrupts other than NMI when set to 1. NMI is accepted regardless of the I bit setting. The I bit is set to 1 at the start of an exception-handling sequence. Bit 6--User Bit or Interrupt Mask Bit (UI): Can be written and read by software using the LDC, STC, ANDC, ORC, and XORC instructions. This bit can also be used as an interrupt mask bit. For details see section 5, Interrupt Controller.
Rev.2.00 Mar. 22, 2007 Page 21 of 684 REJ09B0352-0200
2. CPU
Bit 5--Half-Carry Flag (H): When the ADD.B, ADDX.B, SUB.B, SUBX.B, CMP.B, or NEG.B instruction is executed, this flag is set to 1 if there is a carry or borrow at bit 3, and cleared to 0 otherwise. When the ADD.W, SUB.W, CMP.W, or NEG.W instruction is executed, the H flag is set to 1 if there is a carry or borrow at bit 11, and cleared to 0 otherwise. When the ADD.L, SUB.L, CMP.L, or NEG.L instruction is executed, the H flag is set to 1 if there is a carry or borrow at bit 27, and cleared to 0 otherwise. Bit 4--User Bit (U): Can be written and read by software using the LDC, STC, ANDC, ORC, and XORC instructions. Bit 3--Negative Flag (N): Indicates the most significant bit (sign bit) of data. Bit 2--Zero Flag (Z): Set to 1 to indicate zero data, and cleared to 0 to indicate non-zero data. Bit 1--Overflow Flag (V): Set to 1 when an arithmetic overflow occurs, and cleared to 0 at other times. Bit 0--Carry Flag (C): Set to 1 when a carry occurs, and cleared to 0 otherwise. Used by: * Add instructions, to indicate a carry * Subtract instructions, to indicate a borrow * Shift and rotate instructions, to store the value shifted out of the end bit The carry flag is also used as a bit accumulator by bit manipulation instructions. Some instructions leave flag bits unchanged. Operations can be performed on CCR by the LDC, STC, ANDC, ORC, and XORC instructions. The N, Z, V, and C flags are used by conditional branch (Bcc) instructions. For the action of each instruction on the flag bits, see appendix A.1, Instruction List. For the I and UI bits, see section 5, Interrupt Controller. 2.4.4 Initial CPU Register Values
In reset exception handling, PC is initialized to a value loaded from the vector table, and the I bit in CCR is set to 1. The other CCR bits and the general registers are not initialized. In particular, the stack pointer (ER7) is not initialized. The stack pointer must therefore be initialized by an MOV.L instruction executed immediately after a reset.
Rev.2.00 Mar. 22, 2007 Page 22 of 684 REJ09B0352-0200
2. CPU
2.5
Data Formats
The H8/300H CPU can process 1-bit, 4-bit (BCD), 8-bit (byte), 16-bit (word), and 32-bit (longword) data. Bit-manipulation instructions operate on 1-bit data by accessing bit n (n = 0, 1, 2, ..., 7) of byte operand data. The DAA and DAS decimal-adjust instructions treat byte data as two digits of 4-bit BCD data. 2.5.1 General Register Data Formats
Figures 2.6 and 2.7 show the data formats in general registers.
General Register
Data Type
Data Format 7 0 Don't care 7 0
1-bit data
RnH
76543210
1-bit data
RnL 7
Don't care 43 0
76543210
4-bit BCD data
RnH
Upper digit Lower digit
Don't care 7 43 0
4-bit BCD data
RnL 7
Don't care 0
Upper digit Lower digit
Byte data
RnH MSB LSB 7
Don't care 0 LSB
Byte data
RnL
Don't care MSB
Legend RnH: General register RH RnL: General register RL
Figure 2.6 General Register Data Formats
Rev.2.00 Mar. 22, 2007 Page 23 of 684 REJ09B0352-0200
2. CPU
General Register
Data Type
Data Format 15 0 LSB
Word data
Rn MSB 15 0 LSB 16 15 0 LSB
Word data
En MSB 31
Longword data ERn MSB Legend ERn: General register En: General register E Rn: General register R MSB: Most significant bit LSB: Least significant bit
Figure 2.7 General Register Data Formats 2.5.2 Memory Data Formats
Figure 2.8 shows the data formats on memory. The H8/300H CPU can access word data and longword data on memory, but word or longword data must begin at an even address. If an attempt is made to access word or longword data at an odd address, no address error occurs but the least significant bit of the address is regarded as 0, so the access starts at the preceding address. This also applies to instruction fetches.
Rev.2.00 Mar. 22, 2007 Page 24 of 684 REJ09B0352-0200
2. CPU
Data Type Address Data Format
7 1-bit data Byte data Word data Address L Address L Address 2m Address 2m + 1 Address 2n Longword data Address 2n + 1 Address 2n + 2 Address 2n + 3
MSB
0 6 5 4 3 2 1 0
LSB
7
MSB
MSB LSB
LSB
Figure 2.8 Memory Data Formats When ER7 (SP) is used as an address register to access the stack, the operand size should be word size or longword size.
Rev.2.00 Mar. 22, 2007 Page 25 of 684 REJ09B0352-0200
2. CPU
2.6
2.6.1
Instruction Set
Instruction Set Overview
The H8/300H CPU has 62 types of instructions, which are classified as shown in table 2.1. Table 2.1
Function Data transfer
Instruction Classification
Instruction MOV, PUSH* , POP* , MOVTPE* , MOVFPE*
1 1 2 2
Types 3
Arithmetic operations ADD, SUB, ADDX, SUBX, INC, DEC, ADDS, SUBS, DAA, DAS, 18 MULXU, MULXS, DIVXU, DIVXS, CMP, NEG, EXTS, EXTU Logic operations Shift operations Bit manipulation Branch System control Block data transfer AND, OR, XOR, NOT SHAL, SHAR, SHLL, SHLR, ROTL, ROTR, ROTXL, ROTXR 4 8
BSET, BCLR, BNOT, BTST, BAND, BIAND, BOR, BIOR, BXOR, 14 BIXOR, BLD, BILD, BST, BIST Bcc* , JMP, BSR, JSR, RTS TRAPA, RTE, SLEEP, LDC, STC, ANDC, ORC, XORC, NOP EEPMOV
3
5 9 1 Total 62 types
Notes: 1. POP.W Rn is identical to MOV.W @SP+, Rn. PUSH.W Rn is identical to MOV.W Rn, @-SP. POP.L ERn is identical to MOV.L @SP+, Rn. PUSH.L ERn is identical to MOV.L Rn, @-SP. 2. These instructions are not available on the H8/3022 Group. 3. Bcc is a generic branching instruction.
Rev.2.00 Mar. 22, 2007 Page 26 of 684 REJ09B0352-0200
2. CPU
2.6.2
Instructions and Addressing Modes
Table 2.2 indicates the instructions available in the H8/300H CPU. Table 2.2 Instructions and Addressing Modes
Addressing Modes @ @ @ Function Data transfer Instruction #xx MOV POP, PUSH MOVFPE, MOVTPE Arithmetic operations ADD, CMP SUB ADDX, SUBX ADDS, SUBS INC, DEC DAA, DAS MULXU, MULXS, DIVXU, DIVXS NEG EXTU, EXTS Logic operations AND, OR, XOR NOT Shift instructions Bit manipulation -- -- -- BWL -- BWL -- B B -- -- -- -- -- -- -- -- -- -- -- B -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- BWL BWL -- -- -- -- -- -- -- -- -- -- -- -- -- BWL -- WL -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- BWL -- B BW -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- L -- -- -- -- -- -- -- -- -- -- -- BWL BWL -- WL B BWL -- B -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- B -- -- -- -- -- Rn ERn (d:16, ERn) @ (d:24, ERn) BWL -- ERn+ /@ -ERn BWL -- @ aa: 8 B -- @ aa: 16 @ aa: 24 @ PC) @ (d: @@ aa:8 -- -- Implied -- WL PC) -- -- (d:8, 16,
BWL BWL BWL BWL -- -- -- --
BWL BWL -- -- -- --
Rev.2.00 Mar. 22, 2007 Page 27 of 684 REJ09B0352-0200
2. CPU
Addressing Modes @ @ @ Function Branch Instruction #xx Bcc, BSR JMP, JSR RTS System control TRAPA RTE SLEEP LDC STC ANDC, ORC, XORC NOP Block data transfer -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- BW -- -- -- -- -- -- B -- B Rn -- -- -- -- -- -- B B -- -- -- -- -- W W -- ERn -- (d:16, ERn) -- -- -- -- -- -- W W -- @ (d:24, ERn) -- -- -- -- -- -- W W -- ERn+ /@ -ERn -- -- -- -- -- -- W W -- @ aa: 8 -- -- -- -- -- -- -- -- -- @ aa: 16 -- -- -- -- -- -- W W -- -- -- -- -- W W -- @ aa: 24 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- @ PC) @ (d: @@ aa:8 -- Implied -- -- PC) (d:8, 16,
Legend B: Byte W: Word L: Longword
Rev.2.00 Mar. 22, 2007 Page 28 of 684 REJ09B0352-0200
2. CPU
2.6.3
Tables of Instructions Classified by Function
Tables 2.3 to 2.10 summarize the instructions in each functional category. The operation notation used in these tables is defined as follows. Operation Notation
Rd Rs Rn ERn (EAd) (EAs) CCR N Z V C PC SP #IMM disp + - x / :3/:8/:16/:24 Note: * General register (destination)* General register (source)* General register* General register (32-bit register or address register) Destination operand Source operand Condition code register N (negative) flag of CCR Z (zero) flag of CCR V (overflow) flag of CCR C (carry) flag of CCR Program counter Stack pointer Immediate data Displacement Addition Subtraction Multiplication Division Logical AND Logical OR Exclusive logical OR Move NOT (logical complement) 3-, 8-, 16-, or 24-bit length General registers include 8-bit registers (R0H to R7H, R0L to R7L), 16-bit registers (R0 to R7, E0 to E7), and 32-bit data or address registers (ER0 to ER7).
Rev.2.00 Mar. 22, 2007 Page 29 of 684 REJ09B0352-0200
2. CPU
Table 2.3
Instruction MOV
Data Transfer Instructions
Size* B/W/L Function (EAs) Rd, Rs (EAd) Moves data between two general registers or between a general register and memory, or moves immediate data to a general register.
MOVFPE MOVTPE POP
B B W/L
(EAs) Rd Cannot be used in the H8/3022 Group. Rs (EAs) Cannot be used in the H8/3022 Group. @SP+ Rn Pops a general register from the stack. POP.W Rn is identical to MOV.W @SP+, Rn. Similarly, POP.L ERn is identical to MOV.L @SP+, ERn.
PUSH
W/L
Rn @-SP Pushes a general register onto the stack. PUSH.W Rn is identical to MOV.W Rn, @-SP. Similarly, PUSH.L ERn is identical to MOV.L ERn, @-SP.
Note:
* B: W: L:
Size refers to the operand size. Byte Word Longword
Rev.2.00 Mar. 22, 2007 Page 30 of 684 REJ09B0352-0200
2. CPU
Table 2.4
Instruction ADD, SUB
Arithmetic Operation Instructions
Size* B/W/L Function Rd Rs Rd, Rd #IMM Rd Performs addition or subtraction on data in two general registers, or on immediate data and data in a general register. (Immediate byte data cannot be subtracted from data in a general register. Use the SUBX or ADD instruction.) B Rd Rs C Rd, Rd #IMM C Rd Performs addition or subtraction with carry on data in two general registers, or on immediate data and data in a general register. B/W/L Rd 1 Rd, Rd 2 Rd Increments or decrements a general register by 1 or 2. (Byte operands can be incremented or decremented by 1 only.) L Rd 1 Rd, Rd 2 Rd, Rd 4 Rd Adds or subtracts the value 1, 2, or 4 to or from data in a 32-bit register. B Rd decimal adjust Rd Decimal-adjusts an addition or subtraction result in a general register by referring to CCR to produce 4-bit BCD data. B/W Rd x Rs Rd Performs unsigned multiplication on data in two general registers: either 8 bits x 8 bits 16 bits or 16 bits x 16 bits 32 bits.
ADDX, SUBX INC, DEC ADDS, SUBS DAA, DAS MULXU
MULXS
B/W
Rd x Rs Rd Performs signed multiplication on data in two general registers: either 8 bits x 8 bits 16 bits or 16 bits x 16 bits 32 bits.
Rev.2.00 Mar. 22, 2007 Page 31 of 684 REJ09B0352-0200
2. CPU Instruction DIVXU Size* B/W Function Rd / Rs Rd Performs unsigned division on data in two general registers: either 16 bits / 8 bits 8-bit quotient and 8-bit remainder or 32 bits / 16 bits 16-bit quotient and 16-bit remainder. DIVXS B/W Rd / Rs Rd Performs signed division on data in two general registers: either 16 bits / 8 bits 8-bit quotient and 8-bit remainder, or 32 bits / 16 bits 16-bit quotient and 16-bit remainder. CMP B/W/L Rd - Rs, Rd - #IMM Compares data in a general register with data in another general register or with immediate data, and sets CCR according to the result. NEG B/W/L 0 - Rd Rd Takes the two's complement (arithmetic complement) of data in a general register. EXTS W/L Rd (sign extension) Rd Extends byte data in the lower 8 bits of a 16-bit register to word data, or extends word data in the lower 16 bits of a 32-bit register to longword data, by extending the sign bit. EXTU W/L Rd (zero extension) Rd Extends byte data in the lower 8 bits of a 16-bit register to word data, or extends word data in the lower 16 bits of a 32-bit register to longword data, by padding with zeros. Note: * B: W: L: Size refers to the operand size. Byte Word Longword
Rev.2.00 Mar. 22, 2007 Page 32 of 684 REJ09B0352-0200
2. CPU
Table 2.5
Instruction AND
Logic Operation Instructions
Size* B/W/L Function Rd Rs Rd, Rd #IMM Rd Performs a logical AND operation on a general register and another general register or immediate data.
OR
B/W/L
Rd Rs Rd, Rd #IMM Rd Performs a logical OR operation on a general register and another general register or immediate data.
XOR
B/W/L
Rd Rs Rd, Rd #IMM Rd Performs a logical exclusive OR operation on a general register and another general register or immediate data.
NOT Note: * B: W: L:
B/W/L
Rd Rd Takes the one's complement of general register contents.
Size refers to the operand size. Byte Word Longword
Table 2.6
Instruction SHAL, SHAR SHLL, SHLR ROTL, ROTR ROTXL, ROTXR Note: * B: W: L:
Shift Instructions
Size* B/W/L B/W/L B/W/L B/W/L Function Rd (shift) Rd Performs an arithmetic shift on general register contents. Rd (shift) Rd Performs a logical shift on general register contents. Rd (rotate) Rd Rotates general register contents. Rd (rotate) Rd Rotates general register contents through the carry bit. Size refers to the operand size. Byte Word Longword
Rev.2.00 Mar. 22, 2007 Page 33 of 684 REJ09B0352-0200
2. CPU
Table 2.7
Instruction BSET
Bit Manipulation Instructions
Size* B Function 1 ( of ) Sets a specified bit in a general register or memory operand to 1. The bit number is specified by 3-bit immediate data or the lower 3 bits of a general register.
BCLR
B
0 ( of ) Clears a specified bit in a general register or memory operand to 0. The bit number is specified by 3-bit immediate data or the lower 3 bits of a general register.
BNOT
B
( of ) ( of ) Inverts a specified bit in a general register or memory operand. The bit number is specified by 3-bit immediate data or the lower 3 bits of a general register.
BTST
B
( of ) Z Tests a specified bit in a general register or memory operand and sets or clears the Z flag accordingly. The bit number is specified by 3-bit immediate data or the lower 3 bits of a general register.
BAND
B
C ( of ) C ANDs the carry flag with a specified bit in a general register or memory operand and stores the result in the carry flag.
BIAND
B
C [ ( of )] C ANDs the carry flag with the inverse of a specified bit in a general register or memory operand and stores the result in the carry flag. The bit number is specified by 3-bit immediate data.
Rev.2.00 Mar. 22, 2007 Page 34 of 684 REJ09B0352-0200
2. CPU Instruction BOR Size* B Function C ( of ) C ORs the carry flag with a specified bit in a general register or memory operand and stores the result in the carry flag. BIOR B C [ ( of )] C ORs the carry flag with the inverse of a specified bit in a general register or memory operand and stores the result in the carry flag. The bit number is specified by 3-bit immediate data. BXOR B C ( of ) C Exclusive-ORs the carry flag with a specified bit in a general register or memory operand and stores the result in the carry flag. BIXOR B C [ ( of )] C Exclusive-ORs the carry flag with the inverse of a specified bit in a general register or memory operand and stores the result in the carry flag. The bit number is specified by 3-bit immediate data. BLD B ( of ) C Transfers a specified bit in a general register or memory operand to the carry flag. BILD B ( of ) C Transfers the inverse of a specified bit in a general register or memory operand to the carry flag. The bit number is specified by 3-bit immediate data. BST B C ( of ) Transfers the carry flag value to a specified bit in a general register or memory operand. BIST B C ( of ) Transfers the inverse of the carry flag value to a specified bit in a general register or memory operand. The bit number is specified by 3-bit immediate data. Note: * Size refers to the operand size. B: Byte
Rev.2.00 Mar. 22, 2007 Page 35 of 684 REJ09B0352-0200
2. CPU
Table 2.8
Instruction Bcc
Branching Instructions
Size -- Function Branches to a specified address if a specified condition is true. The branching conditions are listed below. Mnemonic BRA (BT) BRN (BF) BHI BLS Bcc (BHS) BCS (BLO) BNE BEQ BVC BVS BPL BMI BGE BLT BGT BLE Description Always (true) Never (false) High Low or same Condition Always Never CZ=0 CZ=1
Carry clear (high or same) C = 0 Carry set (low) Not equal Equal Overflow clear Overflow set Plus Minus Greater or equal Less than Greater than Less or equal C=1 Z=0 Z=1 V=0 V=1 N=0 N=1 NV=0 NV=1 Z (N V) = 0 Z (N V) = 1
JMP BSR JSR RTS
-- -- -- --
Branches unconditionally to a specified address Branches to a subroutine at a specified address Branches to a subroutine at a specified address Returns from a subroutine
Rev.2.00 Mar. 22, 2007 Page 36 of 684 REJ09B0352-0200
2. CPU
Table 2.9
Instruction TRAPA RTE SLEEP LDC
System Control Instructions
Size* -- -- -- B/W Function Starts trap-instruction exception handling Returns from an exception-handling routine Causes a transition to the power-down state (EAs) CCR Moves the source operand contents to the condition code register. The condition code register size is one byte, but in transfer from memory, data is read by word access.
STC
B/W
CCR (EAd) Transfers the CCR contents to a destination location. The condition code register size is one byte, but in transfer to memory, data is written by word access.
ANDC ORC XORC
B B B
CCR #IMM CCR Logically ANDs the condition code register with immediate data. CCR #IMM CCR Logically ORs the condition code register with immediate data. CCR #IMM CCR Logically exclusive-ORs the condition code register with immediate data.
NOP Note:
--
PC + 2 PC Only increments the program counter.
* Size refers to the operand size. B: Byte W: Word
Rev.2.00 Mar. 22, 2007 Page 37 of 684 REJ09B0352-0200
2. CPU
Table 2.10 Block Transfer Instruction
Instruction EEPMOV.B Size -- Function if R4L 0 then repeat until else next; EEPMOV.W -- if R4 0 then repeat until else next; Transfers a data block according to parameters set in general registers R4L or R4, ER5, and ER6. R4L or R4: Size of block (bytes) ER5: ER6: Starting source address Starting destination address @ER5+ @ER6+, R4 - 1 R4 R4 = 0 @ER5+ @ER6+, R4L - 1 R4L R4L = 0
Execution of the next instruction begins as soon as the transfer is completed.
Rev.2.00 Mar. 22, 2007 Page 38 of 684 REJ09B0352-0200
2. CPU
2.6.4
Basic Instruction Formats
The H8/300H instructions consist of 2-byte (1-word) units. An instruction consists of an operation field (OP field), a register field (r field), an effective address extension (EA field), and a condition field (cc). Operation Field: Indicates the function of the instruction, the addressing mode, and the operation to be carried out on the operand. The operation field always includes the first 4 bits of the instruction. Some instructions have two operation fields. Register Field: Specifies a general register. Address registers are specified by 3 bits, data registers by 3 bits or 4 bits. Some instructions have two register fields. Some have no register field. Effective Address Extension: Eight, 16, or 32 bits specifying immediate data, an absolute address, or a displacement. A 24-bit address or displacement is treated as 32-bit data in which the first 8 bits are 0 (H'00). Condition Field: Specifies the branching condition of Bcc instructions. Figure 2.9 shows examples of instruction formats.
Operation field only op Operation field and register fields op rn rm ADD.B Rn, Rm, etc. NOP, RTS, etc.
Operation field, register fields, and effective address extension op EA (disp) Operation field, effective address extension, and condition field op cc EA (disp) BRA d:8 rn rm MOV.B @(d:16, Rn), Rm
Figure 2.9 Instruction Formats
Rev.2.00 Mar. 22, 2007 Page 39 of 684 REJ09B0352-0200
2. CPU
2.6.5
Notes on Use of Bit Manipulation Instructions
The BSET, BCLR, BNOT, BST, and BIST instructions read a byte of data, modify a bit in the byte, then write the byte back. Care is required when these instructions are used to access registers with write-only bits, or to access ports.
Step 1 2 3 Read Modify Write Description Read one data byte at the specified address Modify one bit in the data byte Write the modified data byte back to the specified address
Example 1: BCLR is executed to clear bit 0 in the port A data direction register (PADDR) under the following conditions. PA7, PA6: PA5 - PA0: Input pins Output pins
The intended purpose of this BCLR instruction is to switch PA0 from output to input. Before Execution of BCLR Instruction
PA7 Input/output DDR Input 0 PA6 Input 0 PA5 Output 1 PA4 Output 1 PA3 Output 1 PA2 Output 1 PA1 Output 1 PA0 Output 1
Execution of BCLR Instruction
BCLR #0, @PADDR ;Clear bit 0 in data direction register
After Execution of BCLR Instruction
PA7 Input/output DDR Output 1 PA6 Output 1 PA5 Output 1 PA4 Output 1 PA3 Output 1 PA2 Output 1 PA1 Output 1 PA0 Input 0
Explanation: To execute the BCLR instruction, the CPU begins by reading PADDR. Since PADDR is a write-only register, it is read as H'FF, even though its true value is H'3F. Next the CPU clears bit 0 of the read data, changing the value to H'FE.
Rev.2.00 Mar. 22, 2007 Page 40 of 684 REJ09B0352-0200
2. CPU
Finally, the CPU writes this value (H'FE) back to PADDR to complete the BCLR instruction. As a result, PA0DDR is cleared to 0, making PA0 an input pin. In addition, PA7DDR and PA6DDR are set to 1, making PA7 and PA6 output pins. The BCLR instruction can be used to clear flags in the on-chip registers. In an interrupt-handling routine, for example, if it is known that the flag is set to 1, it is not necessary to read the flag ahead of time.
2.7
2.7.1
Addressing Modes and Effective Address Calculation
Addressing Modes
The H8/300H CPU supports the eight addressing modes listed in table 2.11. Each instruction uses a subset of these addressing modes. Arithmetic and logic instructions can use the register direct and immediate modes. Data transfer instructions can use all addressing modes except programcounter relative and memory indirect. Bit manipulation instructions use register direct, register indirect, or absolute (@aa:8) addressing mode to specify an operand, and register direct (BSET, BCLR, BNOT, and BTST instructions) or immediate (3-bit) addressing mode to specify a bit number in the operand. Table 2.11 Addressing Modes
No. 1 2 3 4 5 6 7 8 Addressing Mode Register direct Register indirect Register indirect with displacement Register indirect with post-increment Register indirect with pre-decrement Absolute address Immediate Program-counter relative Memory indirect Symbol Rn @ERn @(d:16, ERn)/@d:24, ERn) @ERn+ @-ERn @aa:8/@aa:16/@aa:24 #xx:8/#xx:16/#xx:32 @(d:8, PC)/@(d:16, PC) @@aa:8
1 Register Direct--Rn: The register field of the instruction code specifies an 8-, 16-, or 32-bit register containing the operand. R0H to R7H and R0L to R7L can be specified as 8-bit registers. R0 to R7 and E0 to E7 can be specified as 16-bit registers. ER0 to ER7 can be specified as 32-bit registers.
Rev.2.00 Mar. 22, 2007 Page 41 of 684 REJ09B0352-0200
2. CPU
2 Register Indirect--@ERn: The register field of the instruction code specifies an address register (ERn), the lower 24 bits of which contain the address of the operand. 3 Register Indirect with Displacement--@(d:16, ERn) or @(d:24, ERn): A 16-bit or 24-bit displacement contained in the instruction code is added to the contents of an address register (ERn) specified by the register field of the instruction, and the lower 24 bits of the sum specify the address of a memory operand. A 16-bit displacement is sign-extended when added. 4 Register Indirect with Post-Increment or Pre-Decrement--@ERn+ or @-ERn: * Register indirect with post-increment--@ERn+ The register field of the instruction code specifies an address register (ERn) the lower 24 bits of which contain the address of a memory operand. After the operand is accessed, 1, 2, or 4 is added to the address register contents (32 bits) and the sum is stored in the address register. The value added is 1 for byte access, 2 for word access, or 4 for longword access. For word or longword access, the register value should be even. * Register indirect with pre-decrement--@-ERn The value 1, 2, or 4 is subtracted from an address register (ERn) specified by the register field in the instruction code, and the lower 24 bits of the result become the address of a memory operand. The result is also stored in the address register. The value subtracted is 1 for byte access, 2 for word access, or 4 for longword access. For word or longword access, the resulting register value should be even. 5 Absolute Address--@aa:8, @aa:16, or @aa:24: The instruction code contains the absolute address of a memory operand. The absolute address may be 8 bits long (@aa:8), 16 bits long (@aa:16), or 24 bits long (@aa:24). For an 8-bit absolute address, the upper 16 bits are all assumed to be 1 (H'FFFF). For a 16-bit absolute address the upper 8 bits are a sign extension. A 24-bit absolute address can access the entire address space. Table 2.12 indicates the accessible address ranges.
Rev.2.00 Mar. 22, 2007 Page 42 of 684 REJ09B0352-0200
2. CPU
Table 2.12 Absolute Address Access Ranges
Absolute Address 8 bits (@aa:8) 16 bits (@aa:16) 24 bits (@aa:24) 1-Mbyte Modes H'FFF00 to H'FFFFF (1,048,320 to 1,048,575) H'00000 to H'07FFF, H'F8000 to H'FFFFF (0 to 32,767, 1,015,808 to 1,048,575) H'00000 to H'FFFFF (0 to 1,048,575) 16-Mbyte Modes H'FFFF00 to H'FFFFFF (16,776,960 to 16,777,215) H'000000 to H'007FFF, H'FF8000 to H'FFFFFF (0 to 32,767, 16,744,448 to 16,777,215) H'000000 to H'FFFFFF (0 to 16,777,215)
6 Immediate--#xx:8, #xx:16, or #xx:32: The instruction code contains 8-bit (#xx:8), 16-bit (#xx:16), or 32-bit (#xx:32) immediate data as an operand. The instruction codes of the ADDS, SUBS, INC, and DEC instructions contain immediate data implicitly. The instruction codes of some bit manipulation instructions contain 3-bit immediate data specifying a bit number. The TRAPA instruction code contains 2-bit immediate data specifying a vector address. 7 Program-Counter Relative--@(d:8, PC) or @(d:16, PC): This mode is used in the Bcc and BSR instructions. An 8-bit or 16-bit displacement contained in the instruction code is signextended to 24 bits and added to the 24-bit PC contents to generate a 24-bit branch address. The PC value to which the displacement is added is the address of the first byte of the next instruction, so the possible branching range is -126 to +128 bytes (-63 to +64 words) or -32766 to +32768 bytes (-16383 to +16384 words) from the branch instruction. The resulting value should be an even number. 8 Memory Indirect--@@aa:8: This mode can be used by the JMP and JSR instructions. The instruction code contains an 8-bit absolute address specifying a memory operand. This memory operand contains a branch address. The memory operand is accessed by longword access. The first byte of the memory operand is ignored, generating a 24-bit branch address. See figure 2.10. The upper bits of the 8-bit absolute address are assumed to be 0 (H'0000), so the address range is 0 to 255 (H'000000 to H'0000FF). Note that the first part of this range is also the exception vector area. For further details see section 5, Interrupt Controller.
Rev.2.00 Mar. 22, 2007 Page 43 of 684 REJ09B0352-0200
2. CPU
Specified by @aa:8
Reserved
Branch address
Figure 2.10 Memory-Indirect Branch Address Specification When a word-size or longword-size memory operand is specified, or when a branch address is specified, if the specified memory address is odd, the least significant bit is regarded as 0. The accessed data or instruction code therefore begins at the preceding address. See section 2.5.2, Memory Data Formats. 2.7.2 Effective Address Calculation
Table 2.13 explains how an effective address is calculated in each addressing mode. In the 1-Mbyte operating modes the upper 4 bits of the calculated address are ignored in order to generate a 20-bit effective address.
Rev.2.00 Mar. 22, 2007 Page 44 of 684 REJ09B0352-0200
Table 2.13 Effective Address Calculation
Effective Address Calculation Operand is general register contents 31 23 General register contents 0 0 Effective Address
No.
Addressing Mode and Instruction Format
1
Register direct (Rn)
op
rm rn
2
Register indirect (@ERn)
op 31 General register contents 0
r
3
Register indirect with displacement @(d:16, ERn)/@(d:24, ERn)
23
0
op Sign extension
r
disp
disp
4 31
Register indirect with post-increment or pre-decrement 0 General register contents 23 0
Register indirect with post-increment @ERn+
op
r 31
1, 2, or 4 0 General register contents 23 1, 2, or 4 1 for a byte operand, 2 for a word operand, 4 for a longword operand 0
Register indirect with pre-decrement @ERn
Rev.2.00 Mar. 22, 2007 Page 45 of 684 REJ09B0352-0200
op
r
2. CPU
2. CPU
No. 23 H'FFFF 87 0
Addressing Mode and Instruction Format Effective Address Calculation Effective Address
5
Absolute address @aa:8
op 23
Sign extension
abs 16 15 0
@aa:16 abs 23
op
0
Rev.2.00 Mar. 22, 2007 Page 46 of 684 REJ09B0352-0200
abs Operand is immediate data IMM 23 PC contents 0 23
Sign extension
@aa:24
op
6
Immediate #xx:8, #xx:16, or #xx:32
op
7
Program-counter relative @(d:8, PC) or @(d:16, PC)
0 disp
op
disp
No.
Addressing Mode and Instruction Format Effective Address Calculation Effective Address
8
Memory indirect @@aa:8
Normal mode* 23 H'0000 15 0 Memory contents abs 23 16 15 H'00 0 87 0
op
abs
Advanced mode
op 23 H'0000 31
abs 87 abs 0 Memory contents 23 0 0
Legend r, rm, rn: op: disp: IMM: abs:
Register field Operation field Displacement Immediate data Absolute address
Rev.2.00 Mar. 22, 2007 Page 47 of 684 REJ09B0352-0200
Note: * Normal mode cannot be used with this LSI.
2. CPU
2. CPU
2.8
2.8.1
Processing States
Overview
The H8/300H CPU has four processing states: the program execution state, exception-handling state, power-down state, and reset state. The power-down state includes sleep mode, software standby mode, and hardware standby mode. Figure 2.11 classifies the processing states. Figure 2.13 indicates the state transitions.
Processing states Program execution state The CPU executes program instructions in sequence Exception-handling state A transient state in which the CPU executes a hardware sequence (saving PC and CCR, fetching a vector, etc.) in response to a reset, interrupt, or other exception
Reset state The CPU and all on-chip supporting modules are initialized and halted
Power-down state The CPU is halted to conserve power
Sleep mode
Software standby mode
Hardware standby mode
Figure 2.11 Processing States
Rev.2.00 Mar. 22, 2007 Page 48 of 684 REJ09B0352-0200
2. CPU
2.8.2
Program Execution State
In this state the CPU executes program instructions in normal sequence. 2.8.3 Exception-Handling State
The exception-handling state is a transient state that occurs when the CPU alters the normal program flow due to a reset, interrupt, or trap instruction. The CPU fetches a starting address from the exception vector table and branches to that address. In interrupt and trap exception handling the CPU references the stack pointer (ER7) and saves the program counter and condition code register. Types of Exception Handling and Their Priority: Exception handling is performed for resets, interrupts, and trap instructions. Table 2.14 indicates the types of exception handling and their priority. Trap instruction exceptions are accepted at all times in the program execution state. Table 2.14 Exception Handling Types and Priority
Priority High Type of Exception Reset Detection Timing Synchronized with clock Start of Exception Handling Exception handling starts immediately when RES changes from low to high When an interrupt is requested, exception handling starts at the end of the current instruction or current exception-handling sequence Exception handling starts when a trap (TRAPA) instruction is executed
Interrupt
End of instruction execution or end of exception handling*
Trap instruction Low
When TRAPA instruction is executed
Note: * Interrupts are not detected at the end of the ANDC, ORC, XORC, and LDC instructions, or immediately after reset exception handling.
Figure 2.12 classifies the exception sources. For further details about exception sources, vector numbers, and vector addresses, see section 4, Exception Handling, and section 5, Interrupt Controller.
Rev.2.00 Mar. 22, 2007 Page 49 of 684 REJ09B0352-0200
2. CPU
Reset External interrupts Exception sources Interrupt Internal interrupts (from on-chip supporting modules) Trap instruction
Figure 2.12 Classification of Exception Sources
Program execution state SLEEP instruction with SSBY = 0 End of exception handling Exception Sleep mode
Interrupt NMI, IRQ 0 , IRQ 1, or IRQ 2 interrupt
SLEEP instruction with SSBY = 1
Exception-handling state
Software standby mode
RES = high STBY = high, RES = low
Reset state*1
Hardware standby mode Power-down state
*2
Notes: 1. From any state except hardware standby mode, a transition to the reset state occurs whenever RES goes low. 2. From any state, a transition to hardware standby mode occurs when STBY goes low.
Figure 2.13 State Transitions
Rev.2.00 Mar. 22, 2007 Page 50 of 684 REJ09B0352-0200
2. CPU
2.8.4
Exception-Handling Sequences
Reset Exception Handling: Reset exception handling has the highest priority. The reset state is entered when the RES signal goes low. Reset exception handling starts after that, when RES changes from low to high. When reset exception handling starts the CPU fetches a start address from the exception vector table and starts program execution from that address. All interrupts, including NMI, are disabled during the reset exception-handling sequence and immediately after it ends. Interrupt Exception Handling and Trap Instruction Exception Handling: When these exception-handling sequences begin, the CPU references the stack pointer (ER7) and pushes the program counter and condition code register on the stack. Next, if the UE bit in the system control register (SYSCR) is set to 1, the CPU sets this set to 1, the CPU sets the I bit in the condition code register to 1. If the UE bit is cleared to 0, the CPU sets both the I bit and the UI bit in the condition code register to 1. Then the CPU fetches a start address from the exception vector table and execution branches to that address. Figure 2.14 shows the stack after the exception-handling sequence.
SP-4 SP-3 SP-2 SP-1 SP (ER7) Stack area
SP (ER7) SP+1 SP+2 SP+3 SP+4
CCR
PC
Even address
Before exception handling starts Legend CCR: Condition code register SP: Stack pointer
Pushed on stack
After exception handling ends
Notes: 1. PC is the address of the first instruction executed after the return from the exception-handling routine. 2. Registers must be saved and restored by word access or longword access, starting at an even address.
Figure 2.14 Stack Structure after Exception Handling
Rev.2.00 Mar. 22, 2007 Page 51 of 684 REJ09B0352-0200
2. CPU
2.8.5
Reset State
When the RES input goes low all current processing stops and the CPU enters the reset state. The I bit in the condition code register is set to 1 by a reset. All interrupts are masked in the reset state. Reset exception handling starts when the RES signal changes from low to high. The reset state can also be entered by a watchdog timer overflow. For details see section 10, Watchdog timer. 2.8.6 Power-Down State
In the power-down state the CPU stops operating to conserve power. There are three modes: sleep mode, software standby mode, and hardware standby mode. Sleep Mode: A transition to sleep mode is made if the SLEEP instruction is executed while the SSBY bit is cleared to 0 in the system control register (SYSCR). CPU operations stop immediately after execution of the SLEEP instruction, but the contents of CPU registers are retained. Software Standby Mode: A transition to software standby mode is made if the SLEEP instruction is executed while the SSBY bit is set to 1 in SYSCR. The CPU and clock halt and all on-chip supporting modules stop operating. The on-chip supporting modules are reset, but as long as a specified voltage is supplied the contents of CPU registers and on-chip RAM are retained. The I/O ports also remain in their existing states. Hardware Standby Mode: A transition to hardware standby mode is made when the STBY input goes low. As in software standby mode, the CPU and clock halt and the on-chip supporting modules are reset, but as long as a specified voltage is supplied, on-chip RAM contents are retained. For further information see section 17, Power-Down State.
Rev.2.00 Mar. 22, 2007 Page 52 of 684 REJ09B0352-0200
2. CPU
2.9
2.9.1
Basic Operational Timing
Overview
The H8/300H CPU operates according to the system clock (). The interval from one rise of the system clock to the next rise is referred to as a "state." A memory cycle or bus cycle consists of two or three states. The CPU uses different methods to access on-chip memory, the on-chip supporting modules, and the external address space. Access to the external address space can be controlled by the bus controller. 2.9.2 On-Chip Memory Access Timing
On-chip memory is accessed in two states. The data bus is 16 bits wide, permitting both byte and word access. Figure 2.15 shows the on-chip memory access cycle. Figure 2.16 indicates the pin states.
Bus cycle T1 state Internal address bus Internal read signal Internal data bus (read access) Internal write signal Internal data bus (write access) Write data Read data Address T2 state
Figure 2.15 On-Chip Memory Access Cycle
Rev.2.00 Mar. 22, 2007 Page 53 of 684 REJ09B0352-0200
2. CPU
T1 Address bus AS , RD, WR Address
T2
High High impedance
D7 to D0
Figure 2.16 Pin States during On-Chip Memory Access 2.9.3 On-Chip Supporting Module Access Timing
The on-chip supporting modules are accessed in three states. The data bus is 8 or 16 bits wide, depending on the register being accessed. Figure 2.17 shows the on-chip supporting module access timing. Figure 2.18 indicates the pin states.
Bus cycle T1 state Internal address bus Internal read signal Internal data bus Address T2 state T3 state
Read access
Read data
Internal write signal Write access Internal data bus Write data
Figure 2.17 Access Cycle for On-Chip Supporting Modules
Rev.2.00 Mar. 22, 2007 Page 54 of 684 REJ09B0352-0200
2. CPU
T1 Address bus AS , RD, WR
T2
T3
Address
High High impedance
D7 to D0
Figure 2.18 Pin States during Access to On-Chip Supporting Modules 2.9.4 Access to External Address Space
The external address space is divided into eight areas (areas 0 to 7). Bus-controller settings determine whether each area accessed in two or three states. For details see section 6, Bus Controller.
Rev.2.00 Mar. 22, 2007 Page 55 of 684 REJ09B0352-0200
2. CPU
Rev.2.00 Mar. 22, 2007 Page 56 of 684 REJ09B0352-0200
3. MCU Operating Modes
Section 3 MCU Operating Modes
3.1
3.1.1
Overview
Operating Mode Selection
The H8/3022 Group has five operating modes (modes 1, 3, 5 to7) that are selected by the mode pins (MD2 and MD0) as indicated in table 3.1. The input at these pins determines expanded mode or single-chip mode. Table 3.1 Operating Mode Selection
Mode Pins Operating Mode MD2 -- Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Mode 6 Mode 7 0 0 0 0 1 1 1 1 MD1 0 0 1 1 0 0 1 1 MD0 0 1 0 1 0 1 0 1 Address Space -- Expanded mode -- Expanded mode -- Expanded mode Expanded mode Single-chip advanced mode Description Initial Bus 1 Mode* -- 8 bits -- 8 bits -- 8 bits 8 bits -- On-Chip ROM -- Disabled -- Disabled -- Enabled Enabled Enabled On-Chip RAM -- Enabled* -- Enabled* -- Enabled* Enabled* Enabled*
1 1 2 1 1
Notes: 1. If the RAM enable bit (RAME) in the system control register (SYSCR) is cleared to 0, these addresses become external addresses. 2. In mode 7, clearing bit RAME in SYSCR to 0 and reading the on-chip RAM always return H'FF, and write access is ignored. For details, see section 14.3, Operation.
For the address space size there are two choices: 1 Mbyte, or 16 Mbytes. Modes 1 and 3 are on-chip ROM disable expanded modes capable of accessing external memory and peripheral devices. Mode 1 supports a maximum address space of 1 Mbyte. Mode 3 supports a maximum address space of 16 Mbytes.
Rev.2.00 Mar. 22, 2007 Page 57 of 684 REJ09B0352-0200
3. MCU Operating Modes
Modes 5 and 6 are externally expanded mode that enables access to external memory and peripheral devices and also enables access to the on-chip ROM. Mode 5 supports a maximum address space of 1 Mbyte. Mode 6 supports a maximum address space of 16 Mbyte. Mode 7 is single-chip modes that operate using the on-chip ROM, RAM, and registers. All I/O ports are available. Mode 7 is an advanced mode with a maximum address space of 1 Mbyte. The H8/3022 Group can be used only in modes 1, 3, or 5 to 7. The inputs at the mode pins must select one of these seven modes. The inputs at the mode pins must not be changed during operation. 3.1.2 Register Configuration
The H8/3022 Group has a mode control register (MDCR) that indicates the inputs at the mode pins (MD2 and MD0), and a system control register (SYSCR). Table 3.2 summarizes these registers. Table 3.2
Address* H'FFF1 H'FFF2
Registers
Name Mode control register System control register Abbreviation MDCR SYSCR R/W R R/W Initial Value Undetermined H'0B
Note: * The lower 16 bits of the address are indicated.
Rev.2.00 Mar. 22, 2007 Page 58 of 684 REJ09B0352-0200
3. MCU Operating Modes
3.2
Mode Control Register (MDCR)
MDCR is an 8-bit read-only register that indicates the current operating mode of the H8/3022 Group.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 0 -- 4 -- 0 -- 3 -- 0 -- 2 MDS2 --* R 1 MDS1 --* R 0 MDS0 --* R
Reserved bits
Mode select 2 to 0 Bits indicating the current operating mode
Note: Determined by pins MD2 to MD 0 .
Bits 7 and 6--Reserved: These bits cannot be modified and are always read as 1. Bits 5 to 3--Reserved: These bits cannot be modified and are always read as 0. Bits 2 to 0--Mode Select 2 to 0 (MDS2 to MDS0): These bits indicate the logic levels at pins MD2 to MD0 (the current operating mode). MDS2 to MDS0 correspond to MD2 to MD0. MDS1 and MDS0 are read-only bits. The mode pin (MD2 to MD0) levels are latched when MDCR is read.
Rev.2.00 Mar. 22, 2007 Page 59 of 684 REJ09B0352-0200
3. MCU Operating Modes
3.3
System Control Register (SYSCR)
SYSCR is an 8-bit register that controls the operation of the H8/3022 Group.
Bit Initial value Read/Write 7 SSBY 0 R/W 6 STS2 0 R/W 5 STS1 0 R/W 4 STS0 0 R/W 3 UE 1 R/W 2 NMIEG 0 R/W 1 -- 1 -- 0 RAME 1 R/W RAM enable Enables or disables on-chip RAM Reserved bit NMI edge select Selects the valid edge of the NMI input User bit enable Selects whether to use UI bit in CCR as a user bit or an interrupt mask bit Standby timer select 2 to 0 These bits select the waiting time at recovery from software standby mode Software standby Enables transition to software standby mode
Bit 7--Software Standby (SSBY): Enables transition to software standby mode. (For further information about software standby mode see section 17, Power-Down State.) When software standby mode is exited by an external interrupt, this bit remains set to 1. To clear this bit, write 0.
Bit7 SSBY 0 1 Description SLEEP instruction causes transition to sleep mode SLEEP instruction causes transition to software standby mode (Initial value)
Bits 6 to 4--Standby Timer Select (STS2 to STS0): These bits select the length of time the CPU and on-chip supporting modules wait for the internal clock oscillator to settle when software standby mode is exited by an external interrupt. Set these bits so that the waiting time will be at least 7 ms at the system clock rate. For further information about waiting time selection, see section 17.4.3, Selection of Oscillator Waiting Time after Exit from Software Standby Mode.
Rev.2.00 Mar. 22, 2007 Page 60 of 684 REJ09B0352-0200
3. MCU Operating Modes Bit6 STS2 0 0 0 0 1 1 1 Bit5 STS1 0 0 1 1 0 0 1 Bit4 STS0 0 1 0 1 0 1 --
Description Waiting time = 8,192 states Waiting time = 16,384 states Waiting time = 32,768 states Waiting time = 65,536 states Waiting time = 131,072 states Waiting time = 1,024 states Illegal setting (Initial value)
Bit 3--User Bit Enable (UE): Selects whether to use the UI bit in the condition code register as a user bit or an interrupt mask bit.
Bit 3 UE 0 1 Description UI bit in CCR is used as an interrupt mask bit UI bit in CCR is used as a user bit (Initial value)
Bit 2--NMI Edge Select (NMIEG): Selects the valid edge of the NMI input.
Bit2 NMIEG 0 1 Description An interrupt is requested at the falling edge of NMI An interrupt is requested at the rising edge of NMI (Initial value)
Bit 1--Reserved: This bit cannot be modified and is always read as 1. Bit 0--RAM Enable (RAME): Enables or disables the on-chip RAM. The RAME bit is initialized by the rising edge of the RES signal. It is not initialized in software standby mode.
Bit 0 RAME 0 1 Description On-chip RAM is disabled On-chip RAM is enabled (Initial value)
Rev.2.00 Mar. 22, 2007 Page 61 of 684 REJ09B0352-0200
3. MCU Operating Modes
3.4
3.4.1
Operating Mode Descriptions
Mode 1
Ports 1, 2, and 5 function as address pins A19 to A0, permitting access to a maximum 1-Mbyte address space. The initial bus mode after a reset is 8 bits, with 8-bit access to all areas. 3.4.2 Mode 3
Ports 1, 2, and 5 and part of port A function as address pins A23 to A0, permitting access to a maximum 16-Mbyte address space. The initial bus mode after a reset is 8 bits, with 8-bit access to all areas. A23 to A21 are valid when 0 is written in bits 7 to 5 of the bus release control register (BRCR). (In this mode A20 is always used for address output.) 3.4.3 Mode 5
Ports 1, 2, and 5 can function as address pins A19 to A0, permitting access to a maximum 1-Mbyte address space, but following a reset they are input ports. To use ports 1, 2, and 5 as an address bus, the corresponding bits in their data direction registers (P1DDR, P2DDR, and P5DDR) must be set to 1. The address bus width can be selected freely by setting DDR of ports 1, 2, and 5. The initial bus mode after a reset is 8 bits, with 8-bit access to all areas. 3.4.4 Mode 6
Ports 1, 2, and 5, and port A (PA7 to PA4) function as address pins A23 to A0, permitting access to a maximum 16-Mbyte address space, but following a reset these pins, except for A20, are input ports. To use ports 1, 2, and 5 as address bus pins A19 to A0, the corresponding bits in their data direction registers (P1DDR, P2DDR, and P5DDR) must be set to 1 to select output mode. A23 to A21 are enabled by writing 0 to bits 7 to 5 in the address control register (ADRCR). The address bus width can be selected freely (excluding A20) by setting DDR of ports 1, 2, and 5, and ADRCR. The initial bus mode after a reset is 8 bits, with 8-bit access to all areas. 3.4.5 Mode 7
This mode is an advanced mode with a 1-Mbyte address space which operates using the on-chip ROM, RAM, and registers. All I/O ports are available. Note: The H8/3022 Group cannot be used in mode 2 and 4.
Rev.2.00 Mar. 22, 2007 Page 62 of 684 REJ09B0352-0200
3. MCU Operating Modes
3.5
Pin Functions in Each Operating Mode
The pin functions of ports 1 to 3, port 5 and port A vary depending on the operating mode. Table 3.3 indicates their functions in each operating mode. Table 3.3
Port Port 1 Port 2 Port 3 Port 5 Port A
Pin Functions in Each Mode
Mode 2* -- -- -- --
1
Mode 1 A7 to A0 A15 to A8 D7 to D0 A19 to A16
Mode 3 A7 to A0 A15 to A8 D7 to D0 A19 to A16
3
Mode 4* -- -- -- --
1
Mode 5 P17 to P10* P27 to P20* D7 to D0 P53 to P50* PA7 to PA4
2 2 2
Mode 6 P17 to P10* P27 to P20* D7 to D0 P53 to P50*
2 3 2 2
Mode 7 P17 to P10 P27 to P20 P37 to P30 P53 to P50
PA7 to PA4 --
PA6 to PA4* , -- A20
PA6 to PA4* , PA7 to PA4 A20
Notes: 1. H8/3022 Group cannot be used in these modes. 2. Initial state. These pins become address output pins when the corresponding bits in the data direction registers (P1DDR, P2DDR, P5DDR) are set to 1. 3. Initial state A20 is always an address output pin. PA6 to PA4 are switched over to A23 to A21 output by writing 0 in bits 7 to 5 of ADRCR.
3.6
Memory Map in Each Operating Mode
Figure 3.1 shows a memory map of the H8/3022. Figure 3.2 shows a memory map of the H8/3021. Figure 3.3 shows a memory map of the H8/3020. The address space is divided into eight areas. Modes 1, 3, 5, and 6 are the 8-bit bus mode. The address locations of the on-chip RAM and internal I/O registers differ between the 1-Mbyte modes (modes 1, 5, and 7) and 16-Mbyte modes (mode 3 and 6). The address range specifiable by the CPU in the 8- and 16-bit absolute addressing modes (@aa:8 and @aa:16) also differs.
Rev.2.00 Mar. 22, 2007 Page 63 of 684 REJ09B0352-0200
3. MCU Operating Modes
Mode 1 (1-Mbyte expanded modes with on-chip ROM disabled)
8-bit memory-indirect addresses 16-bit absolute addresses (first half)
Mode 3 (16-Mbyte expanded modes with on-chip ROM disabled)
8-bit memory-indirect addresses
Vector area
Vector area
H'000FF
H'0000FF
H'07FFF
H'007FFF
H'1FFFF H'20000 H'3FFFF H'40000 H'5FFFF H'60000 External address space H'7FFFF H'80000 H'9FFFF H'A0000 H'BFFFF H'C0000 H'DFFFF H'E0000
Area 0 Area 1 Area 2 Area 3 Area 4 Area 5 Area 6 Area 7 H'7FFFFF H'800000 H'9FFFFF H'A00000 H'5FFFFF H'600000 External address space H'3FFFFF H'400000 H'1FFFFF H'200000
Area 0
Area 1
Area 2
Area 3
Area 4 H'F8000
16-bit absolute addresses (second half)
H'FDF0F H'FDF10
Area 5 H'BFFFFF H'C00000 Area 6 H'DFFFFF H'E00000 Area 7
H'FFF00 H'FFF0F H'FFF10 H'FFF1B H'FFF1C H'FFFFF
External address space Ineternal I/O registers
8-bit absolute addresses
On-chip RAM *
H'FF8000
H'FFFF00 H'FFFF0F H'FFFF10 H'FFFF1B H'FFFF1C H'FFFFFF
External address space Internal I/O registers
Note: * External addresses can be accessed by disabling on-chip RAM.
Figure 3.1 H8/3022 Memory Map in Each Operating Mode (1)
Rev.2.00 Mar. 22, 2007 Page 64 of 684 REJ09B0352-0200
8-bit absolute addresses
On-chip RAM *
16-bit absolute addresses (second half)
H'FFDF0F H'FFDF10
16-bit absolute addresses (first half)
H'00000
H'000000
3. MCU Operating Modes
Mode 5 (1-Mbyte expanded mode with on-chip ROM enabled)
8-bit memory-indirect addresses
Mode 6 (16-Mbyte expanded mode with on-chip ROM enabled)
8-bit memory-indirect addresses
Mode 7 (single-chip advanced mode)
8-bit memory-indirect addresses
H'00000
16-bit absolute addresses (first half)
16-bit absolute addresses (first half)
H'000FF On-chip ROM H'07FFF
H'0000FF
H'000FF On-chip ROM H'07FFF
On-chip ROM
H'007FFF
H'1FFFF H'20000 H'3FFFF H'40000 H'5FFFF H'60000 External address space H'7FFFF H'80000 H'9FFFF H'A0000 H'BFFFF H'C0000 H'DFFFF H'E0000
Area 0 Area 1 Area 2 Area 3 Area 4 Area 5 Area 6 Area 7
H'03FFFF H'040000 H'1FFFFF H'200000 H'3FFFFF H'400000 H'5FFFFF H'600000 External address space H'7FFFFF H'800000 H'9FFFFF H'A00000 H'BFFFFF H'C00000 H'DFFFFF H'E00000
Area 0 Area 1 Area 2 Area 3 Area 4 Area 5 Area 6 Area 7 H'3FFFF
H'F8000
16-bit absolute addresses (second half) 16-bit absolute addresses (second half)
H'F8000 H'FDF10 H'FFF00 H'FFF0F
8-bit absolute addresses 16-bit absolute addresses (second half)
H'FFDF0F H'FFDF10 H'FFFF00 H'FFFF0F H'FFFF10
H'FDF0F H'FDF10
8-bit absolute addresses
H'FFF00 H'FFF0F H'FFF10 H'FFF1B H'FFF1C H'FFFFF
External address space Internal I/O registers
H'FFFF1B H'FFFF1C
External address space Internal I/O registers
8-bit absolute addresses
On-chip RAM *
On-chip RAM *
On-chip RAM
H'FFF1C H'FFFFF
Internal I/O registers
H'FFFFFF
Note: * External addresses can be accessed by disabling on-chip RAM.
Figure 3.1 H8/3022 Memory Map in Each Operating Mode (2)
Rev.2.00 Mar. 22, 2007 Page 65 of 684 REJ09B0352-0200
16-bit absolute addresses (first half)
Vector area
H'000000
Vector area
H'00000
Vector area
3. MCU Operating Modes
Mode 1 (1-Mbyte expanded modes with on-chip ROM disabled)
8-bit memory-indirect addresses 16-bit absolute addresses (first half)
Mode 3 (16-Mbyte expanded modes with on-chip ROM disabled) Vector area
8-bit memory-indirect addresses 16-bit absolute addresses (first half)
H'00000
Vector area
H'000000
H'000FF
H'0000FF
H'07FFF
H'007FFF
H'1FFFF H'20000 H'3FFFF H'40000 H'5FFFF H'60000 External address space H'7FFFF H'80000 H'9FFFF H'A0000 H'BFFFF H'C0000 H'DFFFF H'E0000
Area 0 Area 1 Area 2 Area 3 Area 4 Area 5 Area 6 Area 7 H'7FFFFF H'800000 H'9FFFFF H'A00000
16-bit absolute addresses (second half)
Area 0 H'1FFFFF H'200000 Area 1 H'3FFFFF H'400000 Area 2 H'5FFFFF H'600000 External address space
Area 3
Area 4 H'F8000 H'FDF0F H'FDF10 H'FFF00 H'FFF0F H'FFF10 H'FFF1B H'FFF1C H'FFFFF
Area 5 H'BFFFFF H'C00000 Area 6 H'DFFFFF H'E00000 Area 7
External address space Internal I/O registers
8-bit absolute addresses
On-chip RAM*
H'FF8000
16-bit absolute addresses (second half)
H'FFDF0F H'FFDF10 H'FFFF00 H'FFFF0F H'FFFF10 H'FFFF1B H'FFFF1C H'FFFFFF
External address space Internal I/O registers
Note: * External addresses can be accessed by disabling on-chip RAM.
Figure 3.2 H8/3021 Memory Map in Each Operating Mode (1)
Rev.2.00 Mar. 22, 2007 Page 66 of 684 REJ09B0352-0200
8-bit absolute addresses
On-chip RAM*
3. MCU Operating Modes
Mode 5 (1-Mbyte expanded mode with on-chip ROM enabled)
16-bit absolute addresses (first half) 8-bit memory-indirect addresses
Mode 6 (16-Mbyte expanded mode with on-chip ROM enabled)
16-bit absolute addresses (first half) 8-bit memory-indirect addresses
H'000000
Mode 7 (single-chip advanced mode)
8-bit memory-indirect addresses 16-bit absolute addresses (first half)
H'00000
Vector area
Vector area
H'00000
Vector area
H'000FF On-chip ROM H'07FFF
H'0000FF
H'000FF On-chip ROM H'07FFF
On-chip ROM
H'007FFF
H'1FFFF H'20000 H'2FFFF H'30000 Reserved*1 H'3FFFF H'40000 H'5FFFF H'60000 External address space H'7FFFF H'80000 H'9FFFF H'A0000 H'BFFFF H'C0000 H'DFFFF H'E0000
Area 0 Area 1
Area 2 Area 3 Area 4 Area 5 Area 6 Area 7
H'02FFFF H'030000 Reserved*1 H'03FFFF H'040000 H'1FFFFF H'200000 H'3FFFFF H'400000 H'5FFFFF H'600000 External address space H'7FFFFF H'800000 H'9FFFFF H'A00000 H'BFFFFF H'C00000 H'DFFFFF H'E00000
H'2FFFF Area 0 Area 1 Area 2 Area 3 Area 4 Area 5 Area 6 Area 7 H'F8000
H'F8000 H'FDF0F H'FDF10 On-chip RAM*2
H'FFDF0F H'FFDF10
16-bit absolute addresses (second half)
16-bit absolute addresses (second half)
On-chip RAM*2
On-chip RAM
8-bit absolute addresses
8-bit absolute addresses
H'FFFF00 H'FFFF0F H'FFFF10
H'FFF00 H'FFF0F H'FFF10 H'FFF1B H'FFF1C H'FFFFF
H'FFF00 H'FFF0F
External address space Internal I/O registers
H'FFFF1B H'FFFF1C
External address space Internal I/O registers
H'FFF1C H'FFFFF
Internal I/O registers
H'FFFFFF
Notes: 1. Do not access the reserved area. 2. External addresses can be accessed by disabling on-chip RAM.
Figure 3.2 H8/3021 Memory Map in Each Operating Mode (2)
Rev.2.00 Mar. 22, 2007 Page 67 of 684 REJ09B0352-0200
8-bit absolute addresses
16-bit absolute addresses (second half)
H'FDF10
3. MCU Operating Modes
Mode 1 (1-Mbyte expanded modes with on-chip ROM disabled)
16-bit absolute addresses (first half) 8-bit memory-indirect addresses
Mode 3 (16-Mbyte expanded modes with on-chip ROM disabled) Vector area
8-bit memory-indirect addresses 16-bit absolute addresses (first half)
H'00000
Vector area
H'000000
H'000FF
H'0000FF
H'07FFF
H'007FFF
H'1FFFF H'20000 H'3FFFF H'40000 H'5FFFF H'60000 External address space H'7FFFF H'80000 H'9FFFF H'A0000 H'BFFFF H'C0000 H'DFFFF H'E0000
Area 0 Area 1 Area 2 Area 3 Area 4 Area 5 Area 6 Area 7 H'7FFFFF H'800000 H'9FFFFF H'A00000
16-bit absolute addresses (second half)
Area 0 H'1FFFFF H'200000 Area 1 H'3FFFFF H'400000 Area 2 H'5FFFFF H'600000 External address space
Area 3
Area 4 H'F8000 H'FDF0F H'FDF10 H'FEF0F H'FEF10 H'FFF00 H'FFF0F H'FFF10 H'FFF1B H'FFF1C H'FFFFF
Reserved*1
8-bit absolute addresses
Area 5 H'BFFFFF H'C00000 Area 6 H'DFFFFF H'E00000 Area 7 H'FF8000 H'FFDF0F H'FFDF10 H'FFEF0F H'FFEF10 H'FFFF00 H'FFFF0F H'FFFF10 H'FFFF1B H'FFFF1C H'FFFFFF
On-chip RAM*2
External address space Internal I/O registers
External address space Internal I/O registers
Notes: 1. Do not access the reserved area. 2. External addresses can be accessed by disabling on-chip RAM.
Figure 3.3 H8/3020 Memory Map in Each Operating Mode (1)
Rev.2.00 Mar. 22, 2007 Page 68 of 684 REJ09B0352-0200
8-bit absolute addresses
On-chip RAM*2
16-bit absolute addresses (second half)
Reserved*1
3. MCU Operating Modes
Mode 5 (1-Mbyte expanded mode with on-chip ROM enabled)
16-bit absolute addresses (first half) 8-bit memory-indirect addresses
Mode 6 (16-Mbyte expanded mode with on-chip ROM enabled)
16-bit absolute addresses (first half) 8-bit memory-indirect addresses
H'000000
Mode 7 (single-chip advanced mode)
8-bit memory-indirect addresses 16-bit absolute addresses (first half)
H'00000
Vector area
Vector area
H'00000
Vector area
H'000FF On-chip ROM H'07FFF
H'0000FF
H'000FF On-chip ROM H'07FFF
On-chip ROM
H'007FFF
H'1FFFF H'20000 Reserved*1 H'3FFFF H'40000 H'5FFFF H'60000 External address space H'7FFFF H'80000 H'9FFFF H'A0000 H'BFFFF H'C0000 H'DFFFF H'E0000
Area 0 Area 1
H'01FFFF H'020000
H'1FFFF Reserved*1
Area 2 Area 3 Area 4 Area 5 Area 6 Area 7
H'03FFFF H'040000 H'1FFFFF H'200000 H'3FFFFF H'400000 H'5FFFFF H'600000 External address space H'7FFFFF H'800000 H'9FFFFF H'A00000 H'BFFFFF H'C00000 H'DFFFFF H'E00000
Area 0 Area 1 Area 2 Area 3 Area 4 Area 5 Area 6 Area 7 H'F8000
16-bit absolute addresses (second half)
16-bit absolute addresses (second half)
8-bit absolute addresses
8-bit absolute addresses
H'FFFF00 H'FFFF0F H'FFFF10
H'FFF00 H'FFF0F H'FFF10 H'FFF1B H'FFF1C H'FFFFF
H'FFF00 H'FFF0F
External address space Internal I/O registers
H'FFFF1B H'FFFF1C
External address space Internal I/O registers
H'FFF1C H'FFFFF
Internal I/O registers
H'FFFFFF
Notes: 1. Do not access the reserved area. 2. External addresses can be accessed by disabling on-chip RAM.
Figure 3.3 H8/3020 Memory Map in Each Operating Mode (2)
Rev.2.00 Mar. 22, 2007 Page 69 of 684 REJ09B0352-0200
8-bit absolute addresses
On-chip RAM*2
On-chip RAM*2
H'FEF10 On-chip RAM
16-bit absolute addresses (second half)
H'F8000 H'FDF0F H'FDF10 H'FEF0F H'FEF10
Reserved*1
H'FFDF0F H'FFDF10 H'FFEF0F H'FFEF10
Reserved*1
3. MCU Operating Modes
Rev.2.00 Mar. 22, 2007 Page 70 of 684 REJ09B0352-0200
4. Exception Handling
Section 4 Exception Handling
4.1
4.1.1
Overview
Exception Handling Types and Priority
As table 4.1 indicates, exception handling may be caused by a reset, trap instruction, or interrupt. Exception handling is prioritized as shown in table 4.1. If two or more exceptions occur simultaneously, they are accepted and processed in priority order. Trap instruction exceptions are accepted at all times in the program execution state. Table 4.1
Priority High
Exception Types and Priority
Exception Type Reset Interrupt Start of Exception Handling Starts immediately after a low-to-high transition at the RES pin Interrupt requests are handled when execution of the current instruction or handling of the current exception is completed Started by execution of a trap instruction (TRAPA)
Low
Trap instruction (TRAPA)
4.1.2
Exception Handling Operation
Exceptions originate from various sources. Trap instructions and interrupts are handled as follows. 1. The program counter (PC) and condition code register (CCR) are pushed onto the stack. 2. The CCR interrupt mask bit is set to 1. 3. A vector address corresponding to the exception source is generated, and program execution starts from the address indicated in the vector address. For a reset exception, steps 2 and 3 above are carried out.
Rev.2.00 Mar. 22, 2007 Page 71 of 684 REJ09B0352-0200
4. Exception Handling
4.1.3
Exception Vector Table
The exception sources are classified as shown in figure 4.1. Different vectors are assigned to different exception sources. Table 4.2 lists the exception sources and their vector addresses.
* Reset External interrupts: NMI, IRQ0 , IRQ 1, IRQ 4 , IRQ 5 Exception sources * Interrupts * Trap instruction Internal interrupts: 25 interrupts from on-chip supporting modules
Figure 4.1 Exception Sources
Rev.2.00 Mar. 22, 2007 Page 72 of 684 REJ09B0352-0200
4. Exception Handling
Table 4.2
Exception Vector Table
Vector Address*
1
Exception Source Reset Reserved for system use
Vector Number 0 1 2 3 4 5 6
Normal Mode H'0000 to H'0001 H'0002 to H'0003 H'0004 to H'0005 H'0006 to H'0007 H'0008 to H'0009 H'000A to H'000B H'000C to H'000D H'000E to H'000F H'0010 to H'0011 H'0012 to H'0013 H'0014 to H'0015 H'0016 to H'0017 H'0018 to H'0019 H'001A to H'001B H'001C to H'001D H'001E to H'001F H'0020 to H'0021 H'0022 to H'0023 H'0024 to H'0025 H'0026 to H'0027 H'0028 to H'0029 to H'0078 to H'0079
Advanced Mode H'0000 to H'0003 H'0004 to H'0007 H'0008 to H'000B H'000C to H'000F H'0010 to H'0013 H'0014 to H'0017 H'0018 to H'001B H'001C to H'001F H'0020 to H'0023 H'0024 to H'0027 H'0028 to H'002B H'002C to H'002F H'0030 to H'0033 H'0034 to H'0037 H'0038 to H'003B H'003C to H'003F H'0040 to H'0043 H'0044 to H'0047 H'0048 to H'004B H'004C to H'004F H'0050 to H'0053 to H'00F0 to H'00F3
External interrupt (NMI) Trap instruction (4 sources)
7 8 9 10 11
External interrupt
IRQ0 IRQ1
12 13 14 15
Reserved for system use
External interupt
IRQ4 IRQ5
16 17 18 19
Reserved for system use
2
Internal interrupts*
20 to 60
Notes: 1. Lower 16 bits of the address. 2. For the internal interrupt vectors, see section 5.3.3, Interrupt Vector Table.
Rev.2.00 Mar. 22, 2007 Page 73 of 684 REJ09B0352-0200
4. Exception Handling
4.2
4.2.1
Reset
Overview
A reset is the highest-priority exception. When the RES pin goes low, all processing halts and the H8/3022 Group enters the reset state. A reset initializes the internal state of the CPU and the registers of the on-chip supporting modules. Reset exception handling begins when the RES pin changes from low to high. The chip can also be reset by overflow of the watchdog timer. For details see section 10, Watchdog Timer. 4.2.2 Reset Sequence
The H8/3022 Group enters the reset state when the RES pin goes low. To ensure that the chip is reset, hold the RES pin low for at least 20 ms at power-up. To reset the chip during operation, hold the RES pin low for at least 10 system clock () cycles. When using the flash memory version, hold at "Low" level for a least 1usec. See appendix D.2, Pin States at Reset, for the states of the pins in the reset state. When the RES pin goes high after being held low for the necessary time, the H8/3022 Group chip starts reset exception handling as follows. * The internal state of the CPU and the registers of the on-chip supporting modules are initialized, and the I bit is set to 1 in CCR. * The contents of the reset vector address (H'0000 to H'0003 in advanced mode) are read, and program execution starts from the address indicated in the vector address. Figure 4.2 shows the reset sequence in modes 5 and 7.
Rev.2.00 Mar. 22, 2007 Page 74 of 684 REJ09B0352-0200
Vector fetch
Internal processing
Prefetch of first program instruction
RES
Internal address bus (1) (3)
(5)
Internal read signal
Internal write signal (2) (4) (6)
Figure 4.2 Reset Sequence (Modes 5 and 7)
Internal data bus (16-bit width)
4. Exception Handling
Rev.2.00 Mar. 22, 2007 Page 75 of 684 REJ09B0352-0200
(1), (3) (2), (4) (5) (6)
Address of reset vector: (1) = H'000000, (3) = H'000002 Start address (contents of reset vector) Start address First instruction of program
4. Exception Handling
4.2.3
Interrupts after Reset
If an interrupt is accepted after a reset but before the stack pointer (SP) is initialized, PC and CCR will not be saved correctly, leading to a program crash. To prevent this, all interrupt requests, including NMI, are disabled immediately after a reset. The first instruction of the program is always executed immediately after the reset state ends. This instruction should initialize the stack pointer (example: MOV.L #xx:32, SP).
4.3
Interrupts
Interrupt exception handling can be requested by five external sources (NMI, IRQ0, IRQ1, IRQ4, IRQ5) and 25 internal sources in the on-chip supporting modules. Figure 4.3 classifies the interrupt sources and indicates the number of interrupts of each type. The on-chip supporting modules that can request interrupts are the watchdog timer (WDT), 16-bit integrated timer unit (ITU), serial communication interface (SCI), and A/D converter. Each interrupt source has a separate vector address. NMI is the highest-priority interrupt and is always accepted. Interrupts are controlled by the interrupt controller. The interrupt controller can assign interrupts other than NMI to two priority levels, and arbitrate between simultaneous interrupts. Interrupt priorities are assigned in interrupt priority registers A and B (IPRA and IPRB) in the interrupt controller. For details on interrupts see section 5, Interrupt Controller.
External interrupts Interrupts NMI (1) IRQ0 , IRQ1 , IRQ4 , IRQ5 (4) WDT* (1) ITU (15) SCI (8) A/D converter (1)
Internal interrupts
Notes: Numbers in parentheses are the number of interrupt sources. * When the watchdog timer is used as an interval timer, it generates an interrupt request at every counter overflow.
Figure 4.3 Interrupt Sources and Number of Interrupts
Rev.2.00 Mar. 22, 2007 Page 76 of 684 REJ09B0352-0200
4. Exception Handling
4.4
Trap Instruction
Trap instruction exception handling starts when a TRAPA instruction is executed. If the UE bit is set to 1 in the system control register (SYSCR), the exception handling sequence sets the I bit to 1 in CCR. If the UE bit is 0, the I and UI bits are both set to 1. The TRAPA instruction fetches a start address from a vector table entry corresponding to a vector number from 0 to 3, which is specified in the instruction code.
4.5
Stack Status after Exception Handling
Figure 4.4 shows the stack after completion of trap instruction exception handling and interrupt exception handling.
SP-4 SP-3 SP-2 SP-1 SP (ER7)
Stack area
SP (ER7) SP+1 SP+2 SP+3 SP+4
CCR PC E PC H PC L Even address
Before exception handling Save on stack
After exception handling
Legend PCE: Bits 23 to 16 of program counter (PC) PCH: Bits 15 to 8 of program counter (PC) PCL: Bits 7 to 0 of program counter (PC) CCR: Condition code register SP: Stack pointer Notes: 1. PC indicates the address of the first instruction that will be executed after return. 2. Saving and restoring of registers must be conducted at even addresses in word-size or longword-size units.
Figure 4.4 Stack after Completion of Exception Handling (Advanced Mode)
Rev.2.00 Mar. 22, 2007 Page 77 of 684 REJ09B0352-0200
4. Exception Handling
4.6
Notes on Stack Usage
When accessing word data or longword data, the H8/3022 Group regards the lowest address bit as 0. The stack should always be accessed by word access or longword access, and the value of the stack pointer (SP, ER7) should always be kept even. Use the following instructions to save registers: PUSH.W Rn PUSH.L ERn (or MOV.W Rn, @-SP) (or MOV.L ERn, @-SP)
Use the following instructions to restore registers: POP.W Rn POP.L ERn (or MOV.W @SP+, Rn) (or MOV.L @SP+, ERn)
Setting SP to an odd value may lead to a malfunction. Figure 4.5 shows an example of what happens when the SP value is odd.
CCR SP PC
SP
R1L
H'FFEFA H'FFEFB
PC
H'FFEFC H'FFEFD
H'FFEFF SP
TRAPA instruction executed
MOV. B R1L, @-ER7
SP set to H'FFEFF Legend CCR: Condition code register PC: Program counter R1L: General register R1L SP: Stack pointer
Data saved above SP
CCR contents lost
Note: The diagram illustrates modes 1, 3, 5, 6, and 7.
Figure 4.5 Operation when SP Value is Odd
Rev.2.00 Mar. 22, 2007 Page 78 of 684 REJ09B0352-0200
5. Interrupt Controller
Section 5 Interrupt Controller
5.1
5.1.1
Overview
Features
The interrupt controller has the following features: * Interrupt priority registers (IPRs) for setting interrupt priorities Interrupts other than NMI can be assigned to two priority levels on a module-by-module basis in interrupt priority registers A and B (IPRA and IPRB). * Three-level masking by the I and UI bits in the CPU condition code register (CCR) * Independent vector addresses All interrupts are independently vectored; the interrupt service routine does not have to identify the interrupt source. * Five external interrupt pins NMI has the highest priority and is always accepted; either the rising or falling edge can be selected. For each of IRQ0 , IRQ1, IRQ4, and IRQ5, sensing of the falling edge or level sensing can be selected independently.
Rev.2.00 Mar. 22, 2007 Page 79 of 684 REJ09B0352-0200
5. Interrupt Controller
5.1.2
Block Diagram
Figure 5.1 shows a block diagram of the interrupt controller.
CPU ISCR NMI input IRQ input OVF TME . . . . . . . ADI ADIE IRQ input section ISR Priority decision logic IER IPRA, IPRB
Interrupt request Vector number
. . .
I Interrupt controller UE SYSCR Legend I: IER: IPRA: IPRB: ISCR: ISR: SYSCR: UE: UI: Interrupt mask bit IRQ enable register Interrupt priority register A Interrupt priority register B IRQ sense control register IRQ status register System control register User bit enable User bit/interrupt mask bit UI
CCR
Figure 5.1 Interrupt Controller Block Diagram
Rev.2.00 Mar. 22, 2007 Page 80 of 684 REJ09B0352-0200
5. Interrupt Controller
5.1.3
Pin Configuration
Table 5.1 lists the interrupt pins. Table 5.1
Name Nonmaskable interrupt External interrupt request 5, 4, 1, and 0
Interrupt Pins
Abbreviation NMI IRQ5, IRQ4 , and IRQ1 , IRQ0 I/O Input Input Function Nonmaskable interrupt, rising edge or falling edge selectable Maskable interrupts, falling edge or level sensing selectable
5.1.4
Register Configuration
Table 5.2 lists the registers of the interrupt controller. Table 5.2
Address* H'FFF2 H'FFF4 H'FFF5 H'FFF6 H'FFF8 H'FFF9
1
Interrupt Controller Registers
Name System control register IRQ sense control register IRQ enable register IRQ status register Interrupt priority register A Interrupt priority register B Abbreviation SYSCR ISCR IER ISR IPRA IPRB R/W R/W R/W R/W R/(W)* R/W R/W
2
Initial Value H'0B H'00 H'00 H'00 H'00 H'00
Notes: 1. Lower 16 bits of the address. 2. Only 0 can be written, to clear flags.
Rev.2.00 Mar. 22, 2007 Page 81 of 684 REJ09B0352-0200
5. Interrupt Controller
5.2
5.2.1
Register Descriptions
System Control Register (SYSCR)
SYSCR is an 8-bit readable/writable register that controls software standby mode, selects the action of the UI bit in CCR, selects the NMI edge, and enables or disables the on-chip RAM. Only bits 3 and 2 are described here. For the other bits, see section 3.3, System Control Register (SYSCR). SYSCR is initialized to H'0B by a reset and in hardware standby mode. It is not initialized in software standby mode.
Bit Initial value Read/Write 7 SSBY 0 R/W 6 STS2 0 R/W 5 STS1 0 R/W 4 STS0 0 R/W 3 UE 1 R/W 2 NMIEG 0 R/W 1 -- 1 -- 0 RAME 1 R/W
RAM enable Reserved bit Standby timer select 2 to 0 Software standby NMI edge select Selects the NMI input edge User bit enable Selects whether to use the UI bit in CCR as a user bit or interrupt mask bit
Rev.2.00 Mar. 22, 2007 Page 82 of 684 REJ09B0352-0200
5. Interrupt Controller
Bit 3--User Bit Enable (UE): Selects whether to use the UI bit in CCR as a user bit or an interrupt mask bit.
Bit 3 UE 0 1 Description UI bit in CCR is used as interrupt mask bit UI bit in CCR is used as user bit (Initial value)
Bit 2--NMI Edge Select (NMIEG): Selects the NMI input edge.
Bit 2 NMIEG 0 1 Description Interrupt is requested at falling edge of NMI input Interrupt is requested at rising edge of NMI input (Initial value)
Rev.2.00 Mar. 22, 2007 Page 83 of 684 REJ09B0352-0200
5. Interrupt Controller
5.2.2
Interrupt Priority Registers A and B (IPRA, IPRB)
IPRA and IPRB are 8-bit readable/writable registers that control interrupt priority. Interrupt Priority Register A (IPRA): IPRA is an 8-bit readable/writable register in which interrupt priority levels can be set.
Bit Initial value Read/Write 7 IPRA7 0 R/W 6 IPRA6 0 R/W 5 -- 0 R/W 4 IPRA4 0 R/W 3 IPRA3 0 R/W 2 IPRA2 0 R/W 1 IPRA1 0 R/W 0 IPRA0 0 R/W
Priority level A0 Selects the priority level of ITU channel 2 interrupt requests Priority level A1 Selects the priority level of ITU channel 1 interrupt requests Priority level A2 Selects the priority level of ITU channel 0 interrupt requests Priority level A3 Selects the priority level of WDT interrupt requests Priority level A4 Selects the priority level of IRQ4 and IRQ5 interrupt requests Reserved bit Priority level A6 Selects the priority level of IRQ1 interrupt requests Priority level A7 Selects the priority level of IRQ 0 interrupt requests
IPRA is initialized to H'00 by a reset and in hardware standby mode.
Rev.2.00 Mar. 22, 2007 Page 84 of 684 REJ09B0352-0200
5. Interrupt Controller
Bit 7--Priority Level A7 (IPRA7): Selects the priority level of IRQ0 interrupt requests.
Bit7 IPRA7 0 1 Description IRQ0 interrupt requests have priority level 0 (low priority) IRQ0 interrupt requests have priority level 1 (high priority) (Initial value)
Bit 6--Priority Level A6 (IPRA6): Selects the priority level of IRQ1 interrupt requests.
Bit6 IPRA6 0 1 Description IRQ1 interrupt requests have priority level 0 (low priority) IRQ1 interrupt requests have priority level 1 (high priority) (Initial value)
Bit 5--Reserved bit: This bit can be written and read, but it does not affect interrupt priority. Bit 4--Priority Level A4 (IPRA4): Selects the priority level of IRQ4 and IRQ5 interrupt requests.
Bit4 IPRA4 0 1 Description IRQ4, IRQ5 interrupt requests have priority level 0 (low priority) IRQ4, IRQ5 interrupt requests have priority level 1 (high priority) (Initial value)
Bit 3--Priority Level A3 (IPRA3): Selects the priority level of WDT interrupt requests.
Bit3 IPRA3 0 1 Description WDT interrupt requests have priority level 0 (low priority) WDT interrupt requests have priority level 1 (high priority) (Initial value)
Bit 2--Priority Level A2 (IPRA2): Selects the priority level of ITU channel 0 interrupt requests.
Bit2 IPRA2 0 1 Description ITU channel 0 interrupt requests have priority level 0 (low priority) ITU channel 0 interrupt requests have priority level 1 (high priority) (Initial value)
Rev.2.00 Mar. 22, 2007 Page 85 of 684 REJ09B0352-0200
5. Interrupt Controller
Bit 1--Priority Level A1 (IPRA1): Selects the priority level of ITU channel 1 interrupt requests.
Bit1 IPRA1 0 1 Description ITU channel 1 interrupt requests have priority level 0 (low priority) ITU channel 1 interrupt requests have priority level 1 (high priority) (Initial value)
Bit 0--Priority Level A0 (IPRA0): Selects the priority level of ITU channel 2 interrupt requests.
Bit0 IPRA0 0 1 Description ITU channel 2 interrupt requests have priority level 0 (low priority) ITU channel 2 interrupt requests have priority level 1 (high priority) (Initial value)
Rev.2.00 Mar. 22, 2007 Page 86 of 684 REJ09B0352-0200
5. Interrupt Controller
Interrupt Priority Register B (IPRB): IPRB is an 8-bit readable/writable register in which interrupt priority levels can be set.
Bit Initial value Read/Write 7 IPRB7 0 R/W 6 IPRB6 0 R/W 5 -- 0 R/W 4 -- 0 R/W 3 IPRB3 0 R/W 2 IPRB2 0 R/W 1 IPRB1 0 R/W 0 -- 0 R/W
Reserved bit Priority level B1 Selects the priority level of A/D converter interrupt request Priority level B2 Selects the priority level of SCI channel 1 interrupt requests Priority level B3 Selects the priority level of SCI channel 0 interrupt requests Reserved bits Priority level B6 Selects the priority level of ITU channel 4 interrupt requests Priority level B7 Selects the priority level of ITU channel 3 interrupt requests
IPRB is initialized to H'00 by a reset and in hardware standby mode. Bit 7--Priority Level B7 (IPRB7): Selects the priority level of ITU channel 3 interrupt requests.
Bit7 IPRB7 0 1 Description ITU channel 3 interrupt requests have priority level 0 (low priority) ITU channel 3 interrupt requests have priority level 1 (high priority) (Initial value)
Rev.2.00 Mar. 22, 2007 Page 87 of 684 REJ09B0352-0200
5. Interrupt Controller
Bit 6--Priority Level B6 (IPRB6): Selects the priority level of ITU channel 4 interrupt requests.
Bit6 IPRB6 0 1 Description ITU channel 4 interrupt requests have priority level 0 (low priority) ITU channel 4 interrupt requests have priority level 1 (high priority) (Initial value)
Bits 5 and 4--Reserved: These bits can be written and read, but it does not affect interrupt priority. Bit 3--Priority Level B3 (IPRB3): Selects the priority level of SCI channel 0 interrupt requests.
Bit3 IPRB3 0 1 Description SCI channel 0 interrupt requests have priority level 0 (low priority) SCI channel 0 interrupt requests have priority level 1 (high priority) (Initial value)
Bit 2--Priority Level B2 (IPRB2): Selects the priority level of SCI channel 1 interrupt requests.
Bit2 IPRB2 0 1 Description SCI channel 1 interrupt requests have priority level 0 (low priority) SCI channel 1 interrupt requests have priority level 1 (high priority) (Initial value)
Bit 1--Priority Level B1 (IPRB1): Selects the priority level of A/D converter interrupt requests.
Bit1 IPRB1 0 1 Description A/D converter interrupt requests have priority level 0 (low priority) A/D converter interrupt requests have priority level 1 (high priority) (Initial value)
Bit 0--Reserved: This bit can be written and read, but it does not affect interrupt priority.
Rev.2.00 Mar. 22, 2007 Page 88 of 684 REJ09B0352-0200
5. Interrupt Controller
5.2.3
IRQ Status Register (ISR)
ISR is an 8-bit readable/writable register that indicates the status of IRQ0, IRQ1, IRQ4, and IRQ5 interrupt requests.
Bit Initial value Read/Write 7 -- 0 -- 6 -- 0 -- 5 IRQ5F 0 R/(W)* 4 IRQ4F 0 R/(W) * 3 -- 0 -- 2 -- 0 -- 1 IRQ1F 0 R/(W) * 0 IRQ0F 0 R/(W) *
Reserved bits
Reserved bits IRQ 5 to IRQ4 flags These bits indicate IRQ5 and IRQ4 interrupt request status IRQ 1, IRQ 0 flags These bits indicates IRQ1 and IRQ0 interrupt request status
Note: * Only 0 can be written, to clear flags.
ISR is initialized to H'00 by a reset and in hardware standby mode. Bits 7, 6, 3 and 2--Reserved: These bits cannot be modified and are always read as 0. Bits 5, 4, 1 and 0--IRQ5, IRQ4, IRQ1 and IRQ0 Flags (IRQ5F, IRQ4F, IRQ1F, and IRQ0F): These bits indicate the status of IRQ5, IRQ4, IRQ1 and IRQ0 interrupt requests.
Bits 5, 4, 1, and 0 IRQ5F, IRQ4F, IRQ1F, and IRQ0F 0
Description [Clearing conditions] (Initial value)
0 is written in IRQnF after reading the IRQnF flag when IRQnF = 1. IRQnSC = 0, IRQn input is high, and interrupt exception handling is carried out. IRQnSC = 1 and IRQn interrupt exception handling is carried out. 1 [Setting conditions] IRQnSC = 0 and IRQn input is low. IRQnSC = 1 and IRQn input changes from high to low. Note: n = 5, 4, 1 and 0
Rev.2.00 Mar. 22, 2007 Page 89 of 684 REJ09B0352-0200
5. Interrupt Controller
5.2.4
IRQ Enable Register (IER)
IER is an 8-bit readable/writable register that enables or disables IRQ0, IRQ1, IRQ4, and IRQ5 interrupt requests.
Bit Initial value Read/Write 7 -- 0 R/W 6 -- 0 R/W 5 IRQ5E 0 R/W 4 IRQ4E 0 R/W 3 -- 0 R/W 2 -- 0 R/W 1 IRQ1E 0 R/W 0 IRQ0E 0 R/W
Reserved bits
Reserved bits IRQ 5 to IRQ4 enable These bits enable or disable IRQ5 and IRQ4 interrupts IRQ 1 to IRQ0 enable These bits enable or disable IRQ1 and IRQ0 interrupts
IER is initialized to H'00 by a reset and in hardware standby mode. Bits 7, 6, 3, and 2--Reserved: These bits can be written and read, but they do not enable or disable interrupts. Bits 5, 4, 1, and 0--IRQ5, IRQ4, IRQ1, and IRQ0 Enable (IRQ5E, IRQ4E, IRQ1E, IRQ0E): These bits enable or disable IRQ5, IRQ4, IRQ1, IRQ0 interrupts.
Bits 5, 4, 1, and 0 IRQ5E, IRQ4E, IRQ1E, and IRQ0E 0 1
Description IRQ5, IRQ4, IRQ1, IRQ0 interrupts are disabled IRQ5, IRQ4, IRQ1, IRQ0 interrupts are enabled (Initial value)
Rev.2.00 Mar. 22, 2007 Page 90 of 684 REJ09B0352-0200
5. Interrupt Controller
5.2.5
IRQ Sense Control Register (ISCR)
ISCR is an 8-bit readable/writable register that selects level sensing or falling-edge sensing of the inputs at pins IRQ5, IRQ4, IRQ1, and IRQ0
Bit Initial value Read/Write 7 -- 0 R/W 6 -- 0 R/W 5 0 R/W 4 0 R/W 3 -- 0 R/W 2 -- 0 R/W 1 0 R/W 0 0 R/W IRQ5SC IRQ4SC IRQ1SC IRQ0SC
Reserved bits
Reserved bits IRQ 5 and IRQ 4 sense control These bits select level sensing or falling-edge sensing for IRQ5 and IRQ4 interrupts IRQ1 and IRQ 0 sense control These bits select level sensing or falling-edge sensing for IRQ1 and IRQ0 interrupts
ISCR is initialized to H'00 by a reset and in hardware standby mode. Bits 7, 6, 3, and 2--Reserved: These bits are readable/writable and do not affect selection of level sensing or falling-edge sensing. Bits 5, 4, 1, and 0--IRQ5, IRQ4, IRQ1,,and IRQ0 Sense Control (IRQ5SC, IRQ4SC, IRQ1SC, IRQ0SC): These bits selects whether interrupts IRQ5, IRQ4, IRQ1, IRQ0 are requested by level sensing of pins IRQ5, IRQ4, IRQ1, IRQ0 or by falling-edge sensing.
Bits 5, 4, 1, and 0 IRQ5SC, IRQ4SC, IRQ1SC, IRQ0SC 0 1
Description Interrupts are requested when IRQ5, IRQ4, IRQ1, IRQ0 inputs are low Interrupts are requested by falling-edge input at IRQ5, IRQ4, IRQ1, IRQ0 (Initial value)
Rev.2.00 Mar. 22, 2007 Page 91 of 684 REJ09B0352-0200
5. Interrupt Controller
5.3
Interrupt Sources
The interrupt sources include external interrupts (NMI, IRQ5, IRQ4, IRQ1 and IRQ0) and 25 internal interrupts. 5.3.1 External Interrupts
There are five external interrupts: NMI, and IRQ5, IRQ4, IRQ1, and IRQ0. Of these, NMI, IRQ0, IRQ1, can be used to exit software standby mode. NMI: NMI is the highest-priority interrupt and is always accepted, regardless of the states of the I and UI bits in CCR. The NMIEG bit in SYSCR selects whether an interrupt is requested by the rising or falling edge of the input at the NMI pin. NMI interrupt exception handling has vector number 7. IRQ5, IRQ4, IRQ1, IRQ0 Interrupts: These interrupts are requested by input signals at pins IRQ5, IRQ4, IRQ1, IRQ0. The IRQ5, IRQ4, IRQ1, IRQ0 interrupts have the following features. * ISCR settings can select whether an interrupt is requested by the low level of the input at pins IRQ5, IRQ4, IRQ1, IRQ0, or by the falling edge. * IER settings can enable or disable the IRQ5, IRQ4, IRQ1, IRQ0 interrupts. Interrupt priority levels can be assigned by three bits in IPRA (IPRA7, IPRA6, and IPRA4). * The status of IRQ5, IRQ4, IRQ1, IRQ0 interrupt requests is indicated in ISR. The ISR flags can be cleared to 0 by software. Figure 5.2 shows a block diagram of interrupts IRQ5, IRQ4, IRQ1, IRQ0.
IRQnSC IRQnF Edge/level sense circuit IRQn input S R Clear signal Note: n = 5, 4, 1 and 0 Q IRQn interrupt request IRQnE
Figure 5.2 Block Diagram of Interrupts IRQ5, IRQ4, IRQ1, and IRQ0
Rev.2.00 Mar. 22, 2007 Page 92 of 684 REJ09B0352-0200
5. Interrupt Controller
Figure 5.3 shows the timing of the setting of the interrupt flags (IRQnF).
IRQn input pin IRQnF
Note: n = 5, 4, 1 and 0
Figure 5.3 Timing of Setting of IRQnF Interrupts IRQ5, IRQ4, IRQ1, IRQ0 have vector numbers 17, 16, 13, 12. These interrupts are detected regardless of whether the corresponding pin is set for input or output. When using a pin for external interrupt input, clear its DDR bit to 0 and do not use the pin for SCI input or output. 5.3.2 Internal Interrupts
Twenty-five internal interrupts are requested from the on-chip supporting modules. * Each on-chip supporting module has status flags for indicating interrupt status, and enable bits for enabling or disabling interrupts. * Interrupt priority levels can be assigned in IPRA and IPRB. 5.3.3 Interrupt Vector Table
Table 5.3 lists the interrupt sources, their vector addresses, and their default priority order. In the default priority order, smaller vector numbers have higher priority. The priority of interrupts other than NMI can be changed in IPRA and IPRB. The priority order after a reset is the default order shown in table 5.3.
Rev.2.00 Mar. 22, 2007 Page 93 of 684 REJ09B0352-0200
5. Interrupt Controller
Table 5.3
Interrupt Sources, Vector Addresses, and Priority
Vector Number 7 12 13 -- 14 15 Vector Address* Normal Mode Advanced Mode IPR Priority High
Interrupt Source NMI IRQ0 IRQ1 Reserved
Origin External pins
H'000E to H'000F H'001C to H'001F -- H'0018 to H'0019 H'0030 to H'0033 IPRA7 IPRA6 --
H'001A to H'001B H'0034 to H0037 H'001C to H'001D H'0038 to H'003B H'001E to H'001F H'003C to H'003F H'0020 to H'0021 H'0022 to H'0023 H'0024 to H'0025 H'0026 to H'0027 H'0028 to H'0029 H'0040 to H'0043 H'0044 to H'0047 H'0048 to H'004B H'004C to H'004F H'0050 to H'0053
IRQ4 IRQ5 Reserved
External pins --
16 17 18 19
IPRA4
WOVI (interval timer) Reserved
Watchdog timer --
20 21 22 23
IPRA3
H'002A to H'002B H'0054 to H'0057 H'002C to H'002D H'0058 to H'005B H'002E to H'002F H'005C to H'005F H'0030 to H'0031 H'0032 to H'0033 H'0034 to H'0035 H'0036 to H'0037 H'0038 to H'0039 H'0060 to H'0063 H'0064 to H'0067 H'0068 to H'006B H'006C to H'006F H'0070 to H'0073 IPRA1 IPRA2
IMIA0 (compare match/ ITU channel 0 input capture A0) IMIB0 (compare match/ input capture B0) OVI0 (overflow 0) Reserved --
24 25 26 27 28 29 30
IMIA1 (compare match/ ITU channel 1 input capture A1) IMIB1 (compare match/ input capture B1) OVI1 (overflow 1) Reserved --
H'003A to H'003B H'0074 to H'0077 H'003C to H'003D H'0078 to H'007B H'003E to H'003F H'007C to H'007F H'0040 to H'0041 H'0042 to H'0043 H'0044 to H'0045 H'0046 to H'0047 H'0080 to H'0083 H'0084 to H'0087 H'0088 to H'008B H'008C to H'008F IPRA0
31 32 33 34
IMIA2 (compare match/ ITU channel 2 input capture A2) IMIB2 (compare match/ input capture B2) OVI2 (overflow 2) Reserved --
35
Rev.2.00 Mar. 22, 2007 Page 94 of 684 REJ09B0352-0200
5. Interrupt Controller
Vector Number Vector Address* Normal Mode H'0048 to H'0049 Advanced Mode H'0090 to H'0093 IPR IPRB7 Priority
Interrupt Source IMIA3 (compare match/ input capture A3) IMIB3 (compare match/ input capture B3) OVI3 (overflow 3) Reserved IMIA4 (compare match/ input capture A4) IMIB4 (compare match/ input capture B4) OVI4 (overflow 4) Reserved
Origin
ITU 36 channel 3 37 38 -- 39
H'004A to H'004B H'0094 to H'0097 H'004C to H'004D H'0098 to H'009B H'004E to H'004F H'0050 to H'0051 H'0052 to H'0053 H'0054 to H'0055 H'0056 to H'0057 H'0058 to H'0059 H'009C to H'009F H'00A0 to H'00A3 IPRB6 H'00A4 to H'00A7 H'00A8 to H'00AB H'00AC to H'00AF -- H'00B0 to H'00B3
ITU 40 channel 4 41 42 -- 43 44 45 46 47 48 49 50 51
H'005A to H'005B H'00B4 to H'00B7 H'005C to H'005D H'00B8 to H'00BB H'005E to H'005F H'0060 to H'0061 H'0062 to H'0063 H'0064 to H'0065 H'0066 to H'0067 H'0068 to H'0069 H'00BC to H'00BF H'00C0 to H'00C3 H'00C4 to H'00C7 H'00C8 to H'00CB H'00CC to H'00CF H'00D0 to H'00D3 IPRB3
ERI0 (receive error 0) RXI0 (receive data full 0) TXI0 (transmit data empty 0) TEI0 (transmit end 0) ERI1 (receive error 1) RXI1 (receive data full 1) TXI1 (transmit data empty 1) TEI1 (transmit end 1) ADI (A/D end)
SCI 52 channel 53 0 54 55 SCI 56 channel 57 1 58 59 A/D 60
H'006A to H'006B H'00D4 to H'00D7 H'006C to H'006D H'00D8 to H'00DB H'006E to H'006F H'0070 to H'0071 H'0072 to H'0073 H'0074 to H'0075 H'0076 to H'0077 H'0078 to H'0079 H'00DC to H'00DF H'00E0 to H'00E3 IPRB2 H'00E4 to H'00E7 H'00E8 to H'00EB H'00EC to H'00EF H'00F0 to H'00F3 IPRB1 Low
Note: * Lower 16 bits of the address.
Rev.2.00 Mar. 22, 2007 Page 95 of 684 REJ09B0352-0200
5. Interrupt Controller
5.4
5.4.1
Interrupt Operation
Interrupt Handling Process
The H8/3022 Group handles interrupts differently depending on the setting of the UE bit. When UE = 1, interrupts are controlled by the I bit. When UE = 0, interrupts are controlled by the I and UI bits. Table 5.4 indicates how interrupts are handled for all setting combinations of the UE, I, and UI bits. NMI interrupts are always accepted except in the reset and hardware standby states. IRQ interrupts and interrupts from the on-chip supporting modules have their own enable bits. Interrupt requests are ignored when the enable bits are cleared to 0. Table 5.4
SYSCR UE 1 I 0 1 0 0 1
UE, I, and UI Bit Settings and Interrupt Handling
CCR UI -- -- -- 0 1 Description All interrupts are accepted. Interrupts with priority level 1 have higher priority. No interrupts are accepted except NMI. All interrupts are accepted. Interrupts with priority level 1 have higher priority. NMI and interrupts with priority level 1 are accepted. No interrupts are accepted except NMI.
UE = 1: Interrupts IRQ0, IRQ1, IRQ4, and IRQ5 and interrupts from the on-chip supporting modules can all be masked by the I bit in the CPU's CCR. Interrupts are masked when the I bit is set to 1, and unmasked when the I bit is cleared to 0. Interrupts with priority level 1 have higher priority. Figure 5.4 is a flowchart showing how interrupts are accepted when UE = 1.
Rev.2.00 Mar. 22, 2007 Page 96 of 684 REJ09B0352-0200
5. Interrupt Controller
Program execution state
No Interrupt requested? Yes Yes NMI No No Priority level 1? Yes No No Pending
IRQ 0 Yes
IRQ 0 No Yes
IRQ 1 Yes
IRQ 1 Yes
No
ADI Yes
ADI Yes
No I=0 Yes Save PC and CCR I 1 Read vector address Branch to interrupt service routine
Figure 5.4 Process Up to Interrupt Acceptance when UE = 1
Rev.2.00 Mar. 22, 2007 Page 97 of 684 REJ09B0352-0200
5. Interrupt Controller
* If an interrupt condition occurs and the corresponding interrupt enable bit is set to 1, an interrupt request is sent to the interrupt controller. * When the interrupt controller receives one or more interrupt requests, it selects the highestpriority request, following the IPR interrupt priority settings, and holds other requests pending. If two or more interrupts with the same IPR setting are requested simultaneously, the interrupt controller follows the priority order shown in table 5.3. * The interrupt controller checks the I bit. If the I bit is cleared to 0, the selected interrupt request is accepted. If the I bit is set to 1, only NMI is accepted; other interrupt requests are held pending. * When an interrupt request is accepted, interrupt exception handling starts after execution of the current instruction has been completed. * In interrupt exception handling, PC and CCR are saved to the stack area. The PC value that is saved indicates the address of the first instruction that will be executed after the return from the interrupt service routine. * Next the I bit is set to 1 in CCR, masking all interrupts except NMI. * The vector address of the accepted interrupt is generated, and the interrupt service routine starts executing from the address indicated by the contents of the vector address. UE = 0: The I and UI bits in the CPU's CCR and the IPR bits enable three-level masking of IRQ0, IRQ1, IRQ4, and IRQ5 interrupts and interrupts from the on-chip supporting modules. * Interrupt requests with priority level 0 are masked when the I bit is set to 1, and are unmasked when the I bit is cleared to 0. * Interrupt requests with priority level 1 are masked when the I and UI bits are both set to 1, and are unmasked when either the I bit or the UI bit is cleared to 0. For example, if the interrupt enable bits of all interrupt requests are set to 1, IPRA is set to H'10, and IPRB is set to H'00 (giving IRQ4 and IRQ5 interrupt requests priority over other interrupts), interrupts are masked as follows: a. If I = 0, all interrupts are unmasked (priority order: NMI > IRQ4 > IRQ5 >IRQ0 ...). b. If I = 1 and UI = 0, only NMI, IRQ4, and IRQ5 are unmasked. c. If I = 1 and UI = 1, all interrupts are masked except NMI. Figure 5.5 shows the transitions among the above states.
Rev.2.00 Mar. 22, 2007 Page 98 of 684 REJ09B0352-0200
5. Interrupt Controller
I0 a. All interrupts are unmasked I 1, UI 0 b. Only NMI, IRQ 4 , and IRQ 5 are unmasked
I0
Exception handling, or I 1, UI 1
UI 0 Exception handling, or UI 1
c. All interrupts are masked except NMI
Figure 5.5 Interrupt Masking State Transitions (Example) Figure 5.6 is a flowchart showing how interrupts are accepted when UE = 0. * If an interrupt condition occurs and the corresponding interrupt enable bit is set to 1, an interrupt request is sent to the interrupt controller. * When the interrupt controller receives one or more interrupt requests, it selects the highestpriority request, following the IPR interrupt priority settings, and holds other requests pending. If two or more interrupts with the same IPR setting are requested simultaneously, the interrupt controller follows the priority order shown in table 5.3. * The interrupt controller checks the I bit. If the I bit is cleared to 0, the selected interrupt request is accepted regardless of its IPR setting, and regardless of the UI bit. If the I bit is set to 1 and the UI bit is cleared to 0, only NMI and interrupts with priority level 1 are accepted; interrupt requests with priority level 0 are held pending. If the I bit and UI bit are both set to 1, only NMI is accepted; all other interrupt requests are held pending. * When an interrupt request is accepted, interrupt exception handling starts after execution of the current instruction has been completed. * In interrupt exception handling, PC and CCR are saved to the stack area. The PC value that is saved indicates the address of the first instruction that will be executed after the return from the interrupt service routine. * The I and UI bits are set to 1 in CCR, masking all interrupts except NMI. * The vector address of the accepted interrupt is generated, and the interrupt service routine starts executing from the address indicated by the contents of the vector address.
Rev.2.00 Mar. 22, 2007 Page 99 of 684 REJ09B0352-0200
5. Interrupt Controller
Program execution state
No Interrupt requested? Yes Yes NMI No No Priority level 1? Yes No No Pending
IRQ 0 Yes
IRQ 0 No Yes
IRQ 1 Yes
IRQ 1 Yes
No
ADI Yes
ADI Yes
No I=0 Yes No UI = 0 Yes I=0 Yes
No
Save PC and CCR I 1, UI 1 Read vector address Branch to interrupt service routine
Figure 5.6 Process Up to Interrupt Acceptance when UE = 0
Rev.2.00 Mar. 22, 2007 Page 100 of 684 REJ09B0352-0200
5.4.2
Interrupt accepted
Interrupt level decision and wait for end of instruction Instruction Internal prefetch processing Stack Vector fetch
Prefetch of interrupt Internal service routine processing instruction
Interrupt Sequence
Interrupt request signal (1) (3) (5) (7) (9) (11) (13)
Address bus
Internal read signal High (2) (4) (6) (8) (10) (12) (14)
Internal write signal
Internal data bus
Figure 5.7 shows the interrupt sequence in mode 5 when the program code and stack are in an onchip memory area.
Figure 5.7 Interrupt Sequence (Mode 5, Stack in On-Chip Memory)
(6), (8) PC and CCR saved to stack (9), (11) Vector address (10), (12) Starting address of interrupt service routine (contents of vector address) (13) Starting address of interrupt service routine; (13) = (10), (12) (14) First instruction of interrupt service routine
(1)
Instruction prefetch address (not executed; return address, same as PC contents) (2), (4) Instruction code (not executed) (3) Instruction prefetch address (not executed) (5) SP-2 (7) SP-4
5. Interrupt Controller
Rev.2.00 Mar. 22, 2007 Page 101 of 684 REJ09B0352-0200
Note: Mode 5, with program code and stack in on-chip memory area.
5. Interrupt Controller
5.4.3
Interrupt Response Time
Table 5.5 indicates the interrupt response time from the occurrence of an interrupt request until the first instruction of the interrupt service routine is executed. Table 5.5 Interrupt Response Time
External Memory On-Chip No. 1 2 3 4 5 6 Total Item Interrupt priority decision Maximum number of states until end of current instruction Saving PC and CCR to stack Vector fetch Instruction prefetch* Internal processing*
2 3
8-Bit Bus 2 States 2*
1
Memory 2*
1
3 States 2*
1 4
1 to 23 4 4 4 4 19 to 41
1 to 27 8 8 8 4 31 to 57
1 to 31* 12* 12* 12* 4
4 4 4
43 to 73
Notes: 1. 1 state for internal interrupts. 2. Prefetch after the interrupt is accepted and prefetch of the first instruction in the interrupt service routine. 3. Internal processing after the interrupt is accepted and internal processing after prefetch. 4. The number of states increases if wait states are inserted in external memory access.
Rev.2.00 Mar. 22, 2007 Page 102 of 684 REJ09B0352-0200
5. Interrupt Controller
5.5
5.5.1
Usage Notes
Contention between Interrupt and Interrupt-Disabling Instruction
When an instruction clears an interrupt enable bit to 0 to disable the interrupt, the interrupt is not disabled until after execution of the instruction is completed. If an interrupt occurs while a BCLR, MOV, or other instruction is being executed to clear its interrupt enable bit to 0, at the instant when execution of the instruction ends the interrupt is still enabled, so its interrupt exception handling is carried out. If a higher-priority interrupt is also requested, however, interrupt exception handling for the higher-priority interrupt is carried out, and the lower-priority interrupt is ignored. This also applies to the clearing of an interrupt flag. Figure 5.8 shows an example in which an IMIEA bit is cleared to 0 in the ITU's TIER.
TIER write cycle by CPU Internal address bus Internal write signal IMIEA IMIA exception handling
TIER address
IMIA IMFA interrupt signal
Figure 5.8 Contention between Interrupt and Interrupt-Disabling Instruction This type of contention will not occur if the interrupt is masked when the interrupt enable bit or flag is cleared to 0.
Rev.2.00 Mar. 22, 2007 Page 103 of 684 REJ09B0352-0200
5. Interrupt Controller
5.5.2
Instructions that Inhibit Interrupts
The LDC, ANDC, ORC, and XORC instructions inhibit interrupts. When an interrupt occurs, after determining the interrupt priority, the interrupt controller requests a CPU interrupt. If the CPU is currently executing one of these interrupt-inhibiting instructions, however, when the instruction is completed the CPU always continues by executing the next instruction. 5.5.3 Interrupts during EEPMOV Instruction Execution
The EEPMOV.B and EEPMOV.W instructions differ in their reaction to interrupt requests. When the EEPMOV.B instruction is executing a transfer, no interrupts are accepted until the transfer is completed, not even NMI. When the EEPMOV.W instruction is executing a transfer, interrupt requests other than NMI are not accepted until the transfer is completed. If NMI is requested, NMI exception handling starts at a transfer cycle boundary. The PC value saved on the stack is the address of the next instruction. Programs should be coded as follows to allow for NMI interrupts during EEPMOV.W execution:
L1: EEPMOV.W MOV.W R4, R4 BNE L1
5.5.4
Usage Notes
The IRQnF flag specification calls for the flag to be cleared by writing 0 to it after it has been read while set to 1. However, it is possible for the IRQnF flag to be cleared by mistake simply by writing 0 to it, irrespective of whether it has been read while set to 1, with the result that interrupt exception handling is not executed. This will occur when the following conditions are met. 1 Setting conditions (1) Multiple external interrupts (IRQa, IRQb) are being used. (2) Different clearing methods are being used: clearing by writing 0 for the IRQaF flag, and clearing by hardware for the IRQbF flag. (3) A bit-manipulation instruction is used on the IRQ status register for clearing the IRQaF flag, or else ISR is read as a byte unit, the IRQaF flag bit is cleared, and the values read in the other bits are written as a byte unit.
Rev.2.00 Mar. 22, 2007 Page 104 of 684 REJ09B0352-0200
5. Interrupt Controller
2 Generation conditions (1) A read of the ISR register is executed to clear the IRQaF flag while it is set to 1, then the IRQbF flag is cleared by the execution of interrupt exception handling. (2) When the IRQaF flag is cleared, there is contention with IRQb generation (IRQaF flag setting). (IRQbF was 0 when ISR was read to clear the IRQaF flag, but IRQbF is set to 1 before ISR is written to.) If the above setting conditions (1) to (3) and generation conditions (1) and (2) are all fulfilled, when the ISR write in generation condition (2) is performed the IRQbF flag will be cleared inadvertently, and interrupt exception handling will not be executed. However, this inadvertent clearing of the IRQbF flag will not occur if 0 is written to this flag even once between generation conditions (1) and (2).
IRQaF
1 read 0 written
1 read 0 written
IRQbF
1 read
1 IRQb written executed
0 read
0 written
(Inadvertent clearing) Generation condition (1) Generation condition (2)
Figure 5.9 IRQnF Flag when Interrupt Exception Handling is not Executed Either of the methods shown following should be used to prevent this problem.
Rev.2.00 Mar. 22, 2007 Page 105 of 684 REJ09B0352-0200
5. Interrupt Controller
Method 1 When clearing the IRQaF flag, read ISR as a byte unit instead of using a bit-manipulation instruction, and write a byte value that clears the IRQaF flag to 0 and sets the other bits to 1. Example: When a = 0 MOV.B @ISR, R0L MOV.B #HFE, R0L MOV.B R0L, @ISR Method 2 Perform dummy processing within the IRQb interrupt exception handling routine to clear the IRQbF flag. Example: When b = 1 IRQB MOV.B #HFD, R0L MOV.B R0L, @ISR . . .
Rev.2.00 Mar. 22, 2007 Page 106 of 684 REJ09B0352-0200
6. Bus Controller
Section 6 Bus Controller
6.1 Overview
The H8/3022 Group has an on-chip bus controller that divides the external address space into eight areas and can assign different bus specifications to each. This enables different types of memory to be connected easily. 6.1.1 Features
Features of the bus controller are listed below. * Independent settings for address areas 0 to 7 128-kbyte areas in 1-Mbyte mode. 2-Mbyte areas in 16-Mbyte mode. Areas can be designated for two-state or three-state access. Programmable wait mode, pin auto-wait mode, and pin wait modes 0 and 1 can be selected. Zero to three wait states can be inserted automatically.
* Four wait modes
Rev.2.00 Mar. 22, 2007 Page 107 of 684 REJ09B0352-0200
6. Bus Controller
6.1.2
Block Diagram
Figure 6.1 shows a block diagram of the bus controller.
ASTCR Internal address bus WCER Area decoder Internal signals Access state control signal Wait request signal
WAIT
Wait-state controller WCR
Legend ASTCR: Access state control register WCER: Wait state controller enable register WCR: Wait control register
Figure 6.1 Block Diagram of Bus Controller
Rev.2.00 Mar. 22, 2007 Page 108 of 684 REJ09B0352-0200
Internal data bus
Bus control circuit
6. Bus Controller
6.1.3
Pin Configuration
Table 6.1 summarizes the bus controller's input/output pins. Table 6.1
Name Address strobe Read Write
Bus Controller Pins
Abbreviation AS RD WR I/O Output Output Output Function Strobe signal indicating valid address output on the address bus Strobe signal indicating reading from the external address space Strobe signal indicating writing to the external address space, with valid data on the data bus(D7 to D0) Wait request signal for access to external threestate-access areas
Wait
WAIT
Input
6.1.4
Register Configuration
Table 6.2 summarizes the bus controller's registers. Table 6.2
Address* H'FFED H'FFEE H'FFEF H'FFF3 Note: *
Bus Controller Registers
Name Access state control register Wait control register Wait state controller enable register Address control register Lower 16 bits of the address. Abbreviation ASTCR WCR WCER ADRCR R/W R/W R/W R/W R/W Initial Value H'FF H'F3 H'FF H'FE
Rev.2.00 Mar. 22, 2007 Page 109 of 684 REJ09B0352-0200
6. Bus Controller
6.2
6.2.1
Register Descriptions
Access State Control Register (ASTCR)
ASTCR is an 8-bit readable/writable register that selects whether each area is accessed in two states or three states.
Bit Initial value Read/Write 7 AST7 1 R/W 6 AST6 1 R/W 5 AST5 1 R/W 4 AST4 1 R/W 3 AST3 1 R/W 2 AST2 1 R/W 1 AST1 1 R/W 0 AST0 1 R/W
Bits selecting number of states for access to each area
ASTCR is initialized to H'FF by a reset and in hardware standby mode. It is not initialized in software standby mode. Bits 7 to 0--Area 7 to 0 Access State Control (AST7 to AST0): These bits select whether the corresponding area is accessed in two or three states.
Bits 7 to 0 AST7 to AST0 0 1 Description Areas 7 to 0 are accessed in two states Areas 7 to 0 are accessed in three states (Initial value)
ASTCR specifies the number of states in which external areas are accessed. On-chip memory and registers are accessed in a fixed number of states that does not depend on ASTCR settings. Therefore, in the single-chip mode (mode 7), the set value is meaningless.
Rev.2.00 Mar. 22, 2007 Page 110 of 684 REJ09B0352-0200
6. Bus Controller
6.2.2
Wait Control Register (WCR)
WCR is an 8-bit readable/writable register that selects the wait mode for the wait-state controller (WSC) and specifies the number of wait states.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 WMS1 0 R/W 2 WMS0 0 R/W 1 WC1 1 R/W 0 WC0 1 R/W
Reserved bits
Wait count 1/0 These bits select the number of wait states inserted Wait mode select 1/0 These bits select the wait mode
WCR is initialized to H'F3 by a reset and in hardware standby mode. It is not initialized in software standby mode. Bits 7 to 4--Reserved: These bits cannot be modified and are always read as 1. Bits 3 and 2--Wait Mode Select 1 and 0 (WMS1/0): These bits select the wait mode.
Bit3 WMS1 0 Bit2 WMS0 0 1 1 0 1 Description Programmable wait mode No wait states inserted by wait-state controller Pin wait mode 1 Pin auto-wait mode (Initial value)
Rev.2.00 Mar. 22, 2007 Page 111 of 684 REJ09B0352-0200
6. Bus Controller
Bits 1 and 0--Wait Count 1 and 0 (WC1/0): These bits select the number of wait states inserted in access to external three-state-access areas.
Bit1 WC1 0 Bit0 WC0 0 1 1 0 1 Description No wait states inserted by wait-state controller 1 state inserted 2 states inserted 3 states inserted (Initial value)
6.2.3
Wait State Controller Enable Register (WCER)
WCER is an 8-bit readable/writable register that enables or disables wait-state control of external three-state-access areas by the wait-state controller.
Bit Initial value Read/Write 7 WCE7 1 R/W 6 WCE6 1 R/W 5 WCE5 1 R/W 4 WCE4 1 R/W 3 WCE3 1 R/W 2 WCE2 1 R/W 1 WCE1 1 R/W 0 WCE0 1 R/W
Wait state controller enable 7 to 0 These bits enable or disable wait-state control
WCER is initialized to H'FF by a reset and in hardware standby mode. It is not initialized in software standby mode. Bits 7 to 0--Wait-State Controller Enable 7 to 0 (WCE7 to WCE0): These bits enable or disable wait-state control of external three-state-access areas.
Bits 7 to 0 WCE7 to WCE0 0 1 Description Wait-state control disabled (pin wait mode 0) Wait-state control enabled (Initial value)
WCER enables or disables wait-state control of external three-state-access areas. Therefore, in the single-chip mode (mode 7), the set value is meaningless.
Rev.2.00 Mar. 22, 2007 Page 112 of 684 REJ09B0352-0200
6. Bus Controller
6.2.4
Address Control Register (ADRCR)
ADRCR is an 8-bit readable/writable register that enables address output on bus lines A23 to A21.
Bit Initial value Read/Write Initial value Read/Write 7 A23E Modes 1 and 5 to 7 Mode 3 1 -- 1 R/W 6 A22E 1 -- 1 R/W 5 A21E 1 -- 1 R/W 4 -- 1 -- 1 -- 3 -- 1 -- 1 -- 2 -- 1 -- 1 -- Reserved bits 1 -- 1 -- 1 -- 0 -- 0 R/W 0 R/W
Address 23 to 21 enable These bits enable PA6 to PA4 to be used for A23 to A21 address output
ADRCR is initialized to H'FE by a reset and in hardware standby mode. It is not initialized in software standby mode. Bit 7--Address 23 Enable (A23E): Enables PA4 to be used as the A23 address output pin. Writing 0 in this bit enables A23 address output from PA4. In modes other than 3 and 6 this bit cannot be modified and PA4 has its ordinary input/output functions
Bit 7 A23E 0 1 Description PA4 is the A23 address output pin PA4 is the PA4/TP4/TIOCA1 input/output pin (Initial value)
Bit 6--Address 22 Enable (A22E): Enables PA5 to be used as the A22 address output pin. Writing 0 in this bit enables A22 address output from PA5. In modes other than 3 and 6 this bit cannot be modified and PA5 has its ordinary input/output functions.
Bit 6 A22E 0 1 Description PA5 is the A22 address output pin PA5 is the PA5/TP5/TIOCB1 input/output pin (Initial value)
Rev.2.00 Mar. 22, 2007 Page 113 of 684 REJ09B0352-0200
6. Bus Controller
Bit 5--Address 21 Enable (A21E): Enables PA6 to be used as the A21 address output pin. Writing 0 in this bit enables A21 address output from PA6. In modes other than 3 and 6 this bit cannot be modified and PA6 has its ordinary input/output functions.
Bit 5 A21E 0 1 Description PA6 is the A21 address output pin PA6 is the PA6/TP6/TIOCA2 input/output pin (Initial value)
Bits 4 to 0--Reserved
Rev.2.00 Mar. 22, 2007 Page 114 of 684 REJ09B0352-0200
6. Bus Controller
6.3
6.3.1
Operation
Area Division
The external address space is divided into areas 0 to 7. Each area has a size of 128 kbytes in the 1-Mbyte mode and 2 Mbytes in the 16-Mbyte mode. Figure 6.2 shows a general view of the memory map.
H'00000 Area 0 (128 kbytes) H'1FFFF H'20000 Area 1 (128 kbytes) H'3FFFF H'40000 Area 2 (128 kbytes) H'5FFFF H'60000 Area 3 (128 kbytes) H'7FFFF H'80000 Area 4 (128 kbytes) H'9FFFF H'A0000 Area 5 (128 kbytes) H'BFFFF H'C0000
H'000000 Area 0 (2 Mbytes) H'1FFFFF H'200000 Area 1 (2 Mbytes) H'3FFFFF H'400000 Area 2 (2 Mbytes) H'5FFFFF H'600000 Area 3 (2 Mbytes) H'7FFFFF H'800000 Area 4 (2 Mbytes) H'9FFFFF H'A00000 Area 5 (2 Mbytes) H'BFFFFF H'C00000
H'00000 H'1FFFF H'20000
On-chip ROM*1 Area 0 (128 kbytes)
H'000000 H'1FFFFF H'200000
On-chip ROM*1 Area 0 (2 Mbytes)
Area 1 (128 kbytes) H'3FFFF H'40000 Area 2 (128 kbytes) H'5FFFF H'60000 Area 3 (128 kbytes) H'7FFFF H'80000 Area 4 (128 kbytes) H'9FFFF H'A0000 Area 5 (128 kbytes) H'BFFFF H'C0000 H'BFFFFF H'C00000 H'9FFFFF H'A00000 H'7FFFFF H'800000 H'5FFFFF H'600000 H'3FFFFF H'400000
Area 1 (2 Mbytes)
Area 2 (2 Mbytes)
Area 3 (2 Mbytes)
Area 4 (2 Mbytes)
Area 5 (2 Mbytes)
Area 6 (128 kbytes) Area 6 (2 Mbytes) H'DFFFFF H'DFFFF H'E0000 Area 7 (128 kbytes) H'E00000 Area 7 (2 Mbytes) On-chip RAM*1,*2 External address space*3 On-chip I/O registers*1 On-chip RAM*1,*2 External address space*3 On-chip I/O registers*1
Area 6 (128 kbytes) Area 6 (2 Mbytes) H'DFFFF H'DFFFFF H'E0000 Area 7 (128 kbytes) H'E00000 Area 7 (2 Mbytes) On-chip RAM*1,*2 External address space*3 On-chip I/O registers*1 On-chip RAM*1,*2 External address space*3 On-chip I/O registers*1 d. 16-Mbyte modes (mode 6)
H'FFFFF
H'FFFFFF
H'FFFFF
H'FFFFFF
a. 1-Mbyte modes with on-chip ROM disabled (mode 1) Notes:
b. 16-Mbyte modes with on-chip ROM disabled (mode 3)
c. 1-Mbyte mode with on-chip ROM enabled (mode 5)
There is no area division in mode 7. 1. The number of access states to on-chip ROM, on-chip RAM, and on-chip I/O registers is fixed. 2. This area follows area 7 specifications when the RAME bit in SYSCR is 0. 3. This area follows area 7 specifications.
Figure 6.2 Access Area Map (Mode 1, 3, and 5)
Rev.2.00 Mar. 22, 2007 Page 115 of 684 REJ09B0352-0200
6. Bus Controller
The bus specifications for each area can be selected in ASTCR, WCER, and WCR as shown in table 6.3. Table 6.3
ASTCR
Bus Specifications
WCER WCR Bus Width 8 8 8 8 8 8 Bus Specifications Access States 2 3 3 3 3 3
ASTn 0 1
WCEn -- 0 1
WMS1 -- -- 0
WMS0 -- -- 0 1
Wait Mode Disabled Pin wait mode 0 Programmable wait mode Disabled Pin wait mode 1 Pin auto-wait mode
1 Note: n = 0 to 7
0 1
Rev.2.00 Mar. 22, 2007 Page 116 of 684 REJ09B0352-0200
6. Bus Controller
6.3.2
Bus Control Signal Timing
8-Bit, Three-State-Access Areas: Figure 6.3 shows the timing of bus control signals for an 8-bit, three-state-access area. Wait states can be inserted.
Bus cycle T1 T2 T3
Address bus
External address
AS
RD Read access D7 to D0 Valid
WR Write access D7 to D0 Valid
Figure 6.3 Bus Control Signal Timing for 8-Bit, Three-State-Access Area
Rev.2.00 Mar. 22, 2007 Page 117 of 684 REJ09B0352-0200
6. Bus Controller
8-Bit, Two-State-Access Areas: Figure 6.4 shows the timing of bus control signals for an 8-bit, two-state-access area. Wait states cannot be inserted.
Bus cycle T1 T2
Address bus
External address
AS
RD Read access D7 to D0 Valid
WR Write access D7 to D0 Valid
Figure 6.4 Bus Control Signal Timing for 8-Bit, Two-State-Access Area
Rev.2.00 Mar. 22, 2007 Page 118 of 684 REJ09B0352-0200
6. Bus Controller
6.3.3
Wait Modes
Four wait modes can be selected for each area as shown in table 6.4. Table 6.4
ASTCR ASTn Bit 0 1
Wait Mode Selection
WCER WCEn Bit -- 0 1 WCR WMS1 Bit -- -- 0 WMS0 Bit -- -- 0 1 1 0 1 WSC Control Disabled Disabled Enabled Enabled Enabled Enabled Wait Mode No wait states Pin wait mode 0 Programmable wait mode No wait states Pin wait mode 1 Pin auto-wait mode
Note: n = 0 to 7
The ASTn and WCEn bits can be set independently for each area. Bits WMS1 and WMS0 apply to all areas. All areas for which WSC control is enabled operate in the same wait mode.
Rev.2.00 Mar. 22, 2007 Page 119 of 684 REJ09B0352-0200
6. Bus Controller
Pin Wait Mode 0: The wait state controller is disabled. Wait states can only be inserted by WAIT pin control. During access to an external three-state-access area, if the WAIT pin is low at the fall of the system clock () in the T2 state, a wait state (TW) is inserted. If the WAIT pin remains low, wait states continue to be inserted until the WAIT signal goes high. Figure 6.5 shows the timing.
Inserted by WAIT signal T1 T2 TW TW T3
*
*
*
WAIT pin Address bus AS RD Read access Data bus WR Write access Data bus Note: * Arrows indicate time of sampling of the WAIT pin. Write data Read data External address
Figure 6.5 Pin Wait Mode 0
Rev.2.00 Mar. 22, 2007 Page 120 of 684 REJ09B0352-0200
6. Bus Controller
Pin Wait Mode 1: In all accesses to external three-state-access areas, the number of wait states (TW) selected by bits WC1 and WC0 are inserted. If the WAIT pin is low at the fall of the system clock () in the last of these wait states, an additional wait state is inserted. If the WAIT pin remains low, wait states continue to be inserted until the WAIT signal goes high. Pin wait mode 1 is useful for inserting four or more wait states, or for inserting different numbers of wait states for different external devices. If the wait count is 0, this mode operates in the same way as pin wait mode 0. Figure 6.6 shows the timing when the wait count is 1 (WC1 = 0, WC0 = 1) and one additional wait state is inserted by WAIT input.
Inserted by wait count T1 T2 TW Inserted by WAIT signal TW T3
*
*
WAIT pin Address bus AS RD Read data Data bus WR Write access Data bus Note: * Arrows indicate time of sampling of the WAIT pin. Write data External address
Read access
Figure 6.6 Pin Wait Mode 1
Rev.2.00 Mar. 22, 2007 Page 121 of 684 REJ09B0352-0200
6. Bus Controller
Pin Auto-Wait Mode: If the WAIT pin is low, the number of wait states (TW) selected by bits WC1 and WC0 are inserted. In pin auto-wait mode, if the WAIT pin is low at the fall of the system clock () in the T2 state, the number of wait states (TW) selected by bits WC1 and WC0 are inserted. No additional wait states are inserted even if the WAIT pin remains low. Figure 6.7 shows the timing when the wait count is 1.
T1 T2 T3 T1 T2 TW T3
*
*
WAIT pin
Address bus
External address
External address
AS RD Read access Data bus Read data Read data
WR Write access Data bus Write data Write data
Note: * Arrows indicate time of sampling of the WAIT pin.
Figure 6.7 Pin Auto-Wait Mode
Rev.2.00 Mar. 22, 2007 Page 122 of 684 REJ09B0352-0200
6. Bus Controller
Programmable Wait Mode: The number of wait states (TW) selected by bits WC1 and WC0 are inserted in all accesses to external three-state-access areas. Figure 6.8 shows the timing when the wait count is 1 (WC1 = 0, WC0 = 1).
T1 T2 TW T3
Address bus
External address
AS
RD Read access Data bus Read data
WR Write access Data bus Write data
Figure 6.8 Programmable Wait Mode
Rev.2.00 Mar. 22, 2007 Page 123 of 684 REJ09B0352-0200
6. Bus Controller
Example of Wait State Control Settings: A reset initializes ASTCR and WCER to H'FF and WCR to H'F3, selecting programmable wait mode and three wait states for all areas. Software can select other wait modes for individual areas by modifying the ASTCR, WCER, and WCR settings. Figure 6.9 shows an example of wait mode settings.
3-state-access area, programmable wait mode 3-state-access area, programmable wait mode 3-state-access area, pin wait mode 0 3-state-access area, pin wait mode 0 2-state-access area, no wait states inserted 2-state-access area, no wait states inserted 2-state-access area, no wait states inserted 2-state-access area, no wait states inserted Bit: ASTCR H'0F: 7 0 6 0 5 0 4 0 3 1 2 1 1 1 0 1
Area 0 Area 1 Area 2 Area 3 Area 4 Area 5 Area 6 Area 7
WCER H'33:
0
0
1
1
0
0
1
1
WCR H'F3:
--
--
--
--
0
0
1
1
Note: Wait states cannot be inserted in areas designated for two-state access by ASTCR.
Figure 6.9 Wait Mode Settings (Example)
Rev.2.00 Mar. 22, 2007 Page 124 of 684 REJ09B0352-0200
6. Bus Controller
6.3.4
Interconnections with Memory (Example)
For each area, the bus controller can select two- or three-state access. In three-state-access areas, wait states can be inserted in a variety of modes, simplifying the connection of both high-speed and low-speed devices. Figure 6.10 shows a memory map for this example. A 32-kword x 8-bit EPROM is connected to area 2. This device is accessed in three states via an 8-bit bus. Two 32-kword x 8-bit SRAM devices (SRAM1 and SRAM2) are connected to area 3. These devices are accessed in two states via an 8-bit bus. One 32-kword x 8-bit SRAM (SRAM3) is connected to area 7. This device is accessed via an 8-bit bus, using three-state access with an additional wait state inserted in pin auto-wait mode.
Rev.2.00 Mar. 22, 2007 Page 125 of 684 REJ09B0352-0200
6. Bus Controller
H'00000 H'1FFFF H'20000 H'3FFFF H'40000 H'47FFF H'48000 H'5FFFF H'60000 SRAM1, 2 H'6FFFF H'70000 Not used H'7FFFF Areas 4, 5, 6 H'E0000 SRAM3 H'E7FFF Not used On-chip RAM H'FFFFF On-chip I/O registers Area 7 8-bit, three-state-access area (one auto-wait state) Area 3 8-bit, two-state-access area
On-chip ROM
Area 0 Area 1
EPROM Not used
Area 2 8-bit, three-state-access area
Note: The bus width and the number of access states of the on-chip memories and I/O registers are fixed; they cannot be changed by register setting.
Figure 6.10 Memory Map (H8/3022 Mode 5)
Rev.2.00 Mar. 22, 2007 Page 126 of 684 REJ09B0352-0200
6. Bus Controller
6.4
6.4.1
Usage Notes
Register Write Timing
ASTCR and WCER Write Timing: Data written to ASTCR or WCER takes effect starting from the next bus cycle. Figure 6.11 shows the timing when an instruction fetched from area 2 changes area 2 from three-state access to two-state access.
T1 Address 3-state access to area 2 ASTCR address T2 T3 T1 T2 T3 T1 T2
2-state access to area 2
Figure 6.11 ASTCR Write Timing 6.4.2 Precautions on setting ASTCR and ABWCR*
Use the H8/3022 Group on-chip program to set ASTCR and ABWCR as shown below, so that the on-chip ROM access cycle for H8/3022 Group can be emulated using the evaluation chip for support tools. Modes 5 and 7 ASTCR0 = 0 ABWCR = H'FC Note: The ABWCR (bus width control register; lower 16-bit address: H'FFEC) is not built onto this LSI. For detailed features of the ABWCR, see the H8/3048 Group, H8/3048 F-ZTAT Hardware Manual.
Rev.2.00 Mar. 22, 2007 Page 127 of 684 REJ09B0352-0200
6. Bus Controller
Rev.2.00 Mar. 22, 2007 Page 128 of 684 REJ09B0352-0200
7. I/O Ports
Section 7 I/O Ports
7.1 Overview
The H8/3022 Group has nine input/output ports (ports 1, 2, 3, 5, 6, 8, 9, A, and B) and one input port (port 7). Table 7.1 summarizes the port functions. The pins in each port are multiplexed as shown in table 7.1. Each port has a data direction register (DDR) for selecting input or output, and a data register (DR) for storing output data. In addition to these registers, ports 2, and 5 have an input pull-up control register (PCR) for switching input pull-up transistors on and off. Ports 1 to 3 and ports 5, 6, and 8 can drive one TTL load and a 90-pF capacitive load. Ports 9, A, and B can drive one TTL load and a 30-pF capacitive load. Ports 1 to 3 and ports 5, 6, 8, 9, A, and B can drive a Darlington pair. Ports 1, 2, 5, and B can drive LEDs (with 5-mA current sink). Pins P81, P80, PA7 to PA0, and PB3 to PB0 have Schmitt-trigger input circuits. For block diagrams of the ports see appendix C, I/O Port Block Diagrams.
Rev.2.00 Mar. 22, 2007 Page 129 of 684 REJ09B0352-0200
7. I/O Ports
Table 7.1
Port Port 1
Port Functions
Description * * 8-bit I/O port Can drive LEDs 8-bit I/O port Input pullup Can drive LEDs 8-bit I/O port 4-bit I/O port Input pullup Can drive LEDs 4-bit I/O port P65/WR, P64/RD, P63/AS P60/WAIT P37 to P30/ D7 to D0 P53 to P50/ A19 to A16 P27 to P20/ A15 to A8 Address output pins (A15 to A8) Pins P17 to P10/ A7 to A0 Mode 1 Mode 3 Mode 5 Mode 6 Mode 7 Generic input/ output
Address output pins (A7 to A0)
Address output (A7 to A0) and generic input DDR = 0: generic input DDR = 1: address output
Port 2
* * *
Address output (A15 to Generic A8) and generic input input/ DDR = 0: output generic input DDR = 1: address output Generic input/ output
Port 3
*
Data input/output (D7 to D0)
Port 5
* * *
Address output (A19 to A16)
Address output (A19 to Generic A16) and 4-bit generic input/ input output DDR = 0: generic input DDR = 1: address output Generic input/ output
Port 6
*
Bus control signal output (WR, RD, AS)
Bus control signal input/output (WAIT) and 1bit generic input/output Analog input (AN7 to AN0) to A/D converter, and generic input IRQ1 input and 1-bit generic input IRQ1 and IRQ0 input and generic input/ output
Port 7 Port 8
* * *
8-bit Input port 2-bit I/O port P81 and P80have Schmitt inputs
P77 to P70/ AN7 to AN0 P81/ IRQ1
P80/IRQ0
IRQ0 input and 1-bit generic input/output
Rev.2.00 Mar. 22, 2007 Page 130 of 684 REJ09B0352-0200
7. I/O Ports
Port Port 9
Description Pins * 6-bit I/O port P95/SCK1/ IRQ5, P94/SCK0/ IRQ4, P93/RxD1, P92/RxD0, P91/TxD1, P90/TxD0 PA7/TP7/ TIOCB2/A20
Mode 1
Mode 3
Mode 5
Mode 6
Mode 7
Input and output (SCK1, SCK0, RxD1, RxD0, TxD1, TxD0) for serial communication interfaces 1 and 0 (SCI0, 1), IRQ5 and IRQ4 input, and 6-bit generic input/output
Port A
* *
8-bit I/O port Schmitt inputs
Output Address (TP7) from output pro(A20) grammable timing pattern controller (TPC), input or output (TIOCB2) for 16-bit integrated timer unit (ITU), and generic input/output TPC output (TP6 to TP4), ITU input or output (TIOCA2, TIOCB1, TIOCA1), and generic input/output TPC output (TP6 to TP4), ITU input or output (TIOCA2, TIOCB1, TIOCA1), address output (A23 to A21), and generic input/ output
TPC Address output output (TP7), ITU (A20) input or output (TIOCB2), and generic input/ output
TPC output (TP7), ITU input or output (TIOCB2), and generic input/ output
PA6/TP6/ TIOCA2/A21, PA5/TP5/ TIOCB1/A22, PA4/TP4/ TIOCA1/A23
TPC output (TP6 to TP4), ITU input or output (TIOCA2, TIOCB1, TIOCA1), and generic input/ output
TPC output (TP6 to TP4), ITU input or output (TIOCA2, TIOCB1, TIOCA1), address output (A23 to A21), and generic input/ output
TPC output (TP6 to TP4), ITU input or output (TIOCA2, TIOCB1, TIOCA1), and generic input/ output
Rev.2.00 Mar. 22, 2007 Page 131 of 684 REJ09B0352-0200
7. I/O Ports Port Port A Description * * 8-bit I/O port Schmitt inputs Pins PA3/TP3/ TIOCB0/ TCLKD, PA2/TP2/ TIOCA0/ TCLKC, PA1/TP1/ TCLKB, PA0/TP0/ TCLKA PB7/TP15/ ADTRG PB5/TP13/ TOCXB4, PB4/TP12/ TOCXA4, PB3/TP11/ TIOCB4, PB2/TP10/ TIOCA4, PB1/TP9/ TIOCB3, PB0/TP8/ TIOCA3 Mode 1 Mode 3 Mode 5 Mode 6 Mode 7
TPC output (TP3 to TP0), ITU input or output (TCLKD, TCLKC, TCLKB, TCLKA, TIOCB0, TIOCA0), and generic input/output
Port B
* * *
7-bit I/Oport Can drive LEDs PB3 to PB0 have Schmitt inputs
TPC output (TP15), trigger input (ADTRG) to A/D converter, and generic input/output. TPC output (TP13 to TP8), ITU input or output (TOCXB4, TOCXA4, TIOCB4, TIOCA4, TIOCB3, TIOCA3), and generic input/output
Rev.2.00 Mar. 22, 2007 Page 132 of 684 REJ09B0352-0200
7. I/O Ports
7.2
7.2.1
Port 1
Overview
Port 1 is an 8-bit input/output port with the pin configuration shown in figure 7.1. The pin functions differ between the expanded modes with on-chip ROM disabled, expanded modes with on-chip ROM enabled, and single-chip mode. In modes 1, 3 (expanded modes with on-chip ROM disabled), they are address bus output pins (A7 to A0). In modes 5 and 6 (expanded modes with on-chip ROM enabled), settings in the port 1 data direction register (P1DDR) can designate pins for address bus output (A7 to A0) or generic input. In mode 7 (single-chip mode), port 1 is a generic input/output port. Pins in port 1 can drive one TTL load and a 90-pF capacitive load. They can also drive a Darlington transistor pair.
Port 1 pins P17 /A 7 P16 /A 6 P15 /A 5 Port 1 P14 /A 4 P13 /A 3 P12 /A 2 P11 /A 1 P10 /A 0 Modes 1 and 3 Modes 5 and 6 A 7 (output) A 6 (output) A 5 (output) A 4 (output) A 3 (output) A 2 (output) A 1 (output) A 0 (output) P17 (input)/A 7 (output) P16 (input)/A 6 (output) P15 (input)/A 5 (output) P14 (input)/A 4 (output) P13 (input)/A 3 (output) P12 (input)/A 2 (output) P11 (input)/A 1 (output) P10 (input)/A 0 (output) Mode 7 P17 (input/output) P16 (input/output) P15 (input/output) P14 (input/output) P13 (input/output) P12 (input/output) P11 (input/output) P10 (input/output)
Figure 7.1 Port 1 Pin Configuration 7.2.2 Register Descriptions
Table 7.2 summarizes the registers of port 1.
Rev.2.00 Mar. 22, 2007 Page 133 of 684 REJ09B0352-0200
7. I/O Ports
Table 7.2
Port 1 Registers
Initial Value
Address* H'FFC0 H'FFC2 Note:
Name Port 1 data direction register Port 1 data register
Abbreviation P1DDR P1DR
R/W W R/W
Modes 1, 3 H'FF H'00
Modes 5 to 7 H'00 H'00
Lower 16 bits of the address.
Port 1 Data Direction Register (P1DDR): P1DDR is an 8-bit write-only register that can select input or output for each pin in port 1.
Bit Modes Initial value 1, 3 Read/Write Modes Initial value 5 to 7 Read/Write 7 1 -- 0 W 6 1 -- 0 W 5 1 -- 0 W 4 1 -- 0 W 3 1 -- 0 W 2 1 -- 0 W 1 1 -- 0 W 0 1 -- 0 W
P1 7 DDR P1 6 DDR P1 5 DDR P1 4 DDR P1 3 DDR P1 2 DDR P1 1 DDR P1 0 DDR
Port 1 data direction 7 to 0 These bits select input or output for port 1 pins
P1DDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. If a P1DDR bit is set to 1, the corresponding pin maintains its output state in software standby mode. Port 1 Data Register (P1DR): P1DR is an 8-bit readable/writable register that stores data for pins P17 to P10.
Bit Initial value Read/Write 7 P17 0 R/W 6 P16 0 R/W 5 P15 0 R/W 4 P14 0 R/W 3 P13 0 R/W 2 P12 0 R/W 1 P11 0 R/W 0 P10 0 R/W
Port 1 data 7 to 0 These bits store data for port 1 pins
Rev.2.00 Mar. 22, 2007 Page 134 of 684 REJ09B0352-0200
7. I/O Ports
When a bit in P1DDR is set to 1, if port 1 is read the value of the corresponding P1DR bit is returned directly, regardless of the actual state of the pin. When a bit in P1DDR is cleared to 0, if port 1 is read the corresponding pin level is read. P1DR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. 7.2.3 Pin Functions in Each Mode
The pin functions of port 1 differ between mode 1, 3 (expanded mode with on-chip ROM disabled) , modes 5 and 6 (expanded mode with on-chip ROM enabled), and mode 7 (single-chip mode). The pin functions in each mode are described as follows. Modes 1 and 3: Address output can be selected for each pin in port 1. Figure 7.2 shows the pin functions in modes 1 and 3.
A 7 (output) A 6 (output) A 5 (output) Port 1 A 4 (output) A 3 (output) A 2 (output) A 1 (output) A 0 (output)
Figure 7.2 Pin Functions in Modes 1 and 3 (Port 1) Modes 5 and 6: Address output or generic input can be selected for each pin in port 1. A pin becomes an address output pin if the corresponding P1DDR bit is set to 1, and a generic input pin if this bit is cleared to 0. Following a reset, all pins are input pins. To use a pin for address output, its P1DDR bit must be set to 1. Figure 7.3 shows the pin functions in modes 5 and 6.
Rev.2.00 Mar. 22, 2007 Page 135 of 684 REJ09B0352-0200
7. I/O Ports
When P1DDR = 1 A 7 (output) A 6 (output) A 5 (output) Port 1 A 4 (output) A 3 (output) A 2 (output) A 1 (output) A 0 (output) When P1DDR = 0 P17 (input) P16 (input) P15 (input) P14 (input) P13 (input) P12 (input) P11 (input) P10 (input)
Figure 7.3 Pin Functions in Modes 5 and 6 (Port 1) Mode 7 (Single-Chip Mode): Input or output can be selected separately for each pin in port 1. A pin becomes an output pin if the corresponding P1DDR bit is set to 1, and an input pin if this bit is cleared to 0. Figure 7.4 shows the pin functions in mode 7.
P17 (input/output) P16 (input/output) P15 (input/output) Port 1 P14 (input/output) P13 (input/output) P12 (input/output) P11 (input/output) P10 (input/output)
Figure 7.4 Pin Functions in Mode 7 (Port 1)
Rev.2.00 Mar. 22, 2007 Page 136 of 684 REJ09B0352-0200
7. I/O Ports
7.3
7.3.1
Port 2
Overview
Port 2 is an 8-bit input/output port with the pin configuration shown in figure 7.5. Pin functions differ according to operation mode. In modes 1 and 3 (expanded mode with on-chip ROM disabled), port 2 consists of address bus output pins (A15 to A8). In modes 5 and 6 (expanded mode with on-chip ROM enabled), settings in the port 2 data direction register (P2DDR) can designate pins for address bus output (A15 to A8) or generic input. In mode 7 (single-chip mode), port 2 is a generic input/output port. Port 2 has software-programmable built-in pull-up transistors. Pins in port 2 can drive one TTL load and a 90-pF capacitive load. They can also drive a Darlington transistor pair.
Port 2 pins P27 /A 15 P26 /A 14 P25 /A 13 Port 2 P24 /A 12 P23 /A 11 P22 /A 10 P21 /A 9 P20 /A 8 Modes 1 and 3 Modes 5 and 6 A15 (output) A14 (output) A13 (output) A12 (output) A11 (output) A10 (output) A9 (output) A8 (output) P27 (input)/A15 (output) P26 (input)/A14 (output) P25 (input)/A13 (output) P24 (input)/A12 (output) P23 (input)/A11 (output) P22 (input)/A10 (output) P21 (input)/A9 (output) P20 (input)/A8 (output) Mode 7 P27 (input/output) P26 (input/output) P25 (input/output) P24 (input/output) P23 (input/output) P22 (input/output) P21 (input/output) P20 (input/output)
Figure 7.5 Port 2 Pin Configuration
Rev.2.00 Mar. 22, 2007 Page 137 of 684 REJ09B0352-0200
7. I/O Ports
7.3.2
Register Descriptions
Table 7.3 summarizes the registers of port 2. Table 7.3 Port 2 Registers
Initial Value Address* H'FFC1 H'FFC3 H'FFD8 Note: * Name Port 2 data direction register Port 2 data register Abbreviation P2DDR P2DR R/W W R/W R/W Modes 1 and 3 H'FF H'00 H'00 Modes 5 to 7 H'00 H'00 H'00
Port 2 input pull- P2PCR up control register Lower 16 bits of the address.
Port 2 Data Direction Register (P2DDR): P2DDR is an 8-bit write-only register that can select input or output for each pin in port 2.
Bit Modes Initial value 1 and 3 Read/Write Modes Initial value 5 to 7 Read/Write 7 1 -- 0 W 6 1 -- 0 W 5 1 -- 0 W 4 1 -- 0 W 3 1 -- 0 W 2 1 -- 0 W 1 1 -- 0 W 0 1 -- 0 W
P2 7 DDR P2 6 DDR P2 5 DDR P2 4 DDR P2 3 DDR P2 2 DDR P2 1 DDR P2 0 DDR
Port 2 data direction 7 to 0 These bits select input or output for port 2 pins
P2DDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. If a P2DDR bit is set to 1, the corresponding pin maintains its output state in software standby mode.
Rev.2.00 Mar. 22, 2007 Page 138 of 684 REJ09B0352-0200
7. I/O Ports
Port 2 Data Register (P2DR): P2DR is an 8-bit readable/writable register that stores data for pins P27 to P20.
Bit Initial value Read/Write 7 P2 7 0 R/W 6 P2 6 0 R/W 5 P2 5 0 R/W 4 P2 4 0 R/W 3 P2 3 0 R/W 2 P2 2 0 R/W 1 P2 1 0 R/W 0 P2 0 0 R/W
Port 2 data 7 to 0 These bits store data for port 2 pins
When a bit in P2DDR is set to 1, if port 2 is read the value of the corresponding P2DR bit is returned directly, regardless of the actual state of the pin. When a bit in P2DDR is cleared to 0, if port 2 is read the corresponding pin level is read. P2DR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. Port 2 Input Pull-Up Control Register (P2PCR): P2PCR is an 8-bit readable/writable register that controls the MOS input pull-up transistors in port 2.
Bit Initial value Read/Write 7 0 R/W 6 0 R/W 5 0 R/W 4 0 R/W 3 0 R/W 2 0 R/W 1 0 R/W 0 0 R/W
P2 7 PCR P2 6 PCR P2 5 PCR P2 4 PCR P2 3 PCR P2 2 PCR P2 1 PCR P2 0 PCR
Port 2 input pull-up control 7 to 0 These bits control input pull-up transistors built into port 2
When a P2DDR bit is cleared to 0 (selecting generic input) in modes 7 to 5, if the corresponding bit from P27PCR to P20PCR is set to 1, the input pull-up transistor is turned on. P2PCR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it retains its previous setting.
Rev.2.00 Mar. 22, 2007 Page 139 of 684 REJ09B0352-0200
7. I/O Ports
7.3.3
Pin Functions in Each Mode
The pin functions of port 2 differ between mode 1, 3 (expanded mode with on-chip ROM disabled), modes 5 and 6 (expanded mode with on-chip ROM enabled), and mode 7 (single-chip mode). The pin functions in each mode are described followings. Modes 1 and 3: Address output can be selected for each pin in port 2. Figure 7.6 shows the pin functions in modes 1 and 3.
A 15 (output) A 14 (output) A 13 (output) Port 2 A 12 (output) A 11 (output) A 10 (output) A 9 (output) A 8 (output)
Figure 7.6 Pin Functions in Modes 1 and 3 (Port 2) Modes 5 and 6: Address output or generic input can be selected for each pin in port 2. A pin becomes an address output pin if the corresponding P2DDR bit is set to 1, and a generic input pin if this bit is cleared to 0. Following a reset, all pins are input pins. To use a pin for address output, its P2DDR bit must be set to 1. Figure 7.7 shows the pin functions in modes 5 and 6.
Rev.2.00 Mar. 22, 2007 Page 140 of 684 REJ09B0352-0200
7. I/O Ports
When P2DDR = 1 A 15 (output) A 14 (output) A 13 (output) Port 2 A 12 (output) A 11 (output) A 10 (output) A 9 (output) A 8 (output) When P2DDR = 0 P27 (input) P26 (input) P25 (input) P24 (input) P23 (input) P22 (input) P21 (input) P20 (input)
Figure 7.7 Pin Functions in Modes 5 and 6 (Port 2) Mode 7: Input or output can be selected separately for each pin in port 2. A pin becomes an output pin if the corresponding P2DDR bit is set to 1, and an input pin if this bit is cleared to 0. Figure 7.8 shows the pin functions in mode 7.
P27 (input/output) P26 (input/output) P25 (input/output) Port 2 P24 (input/output) P23 (input/output) P22 (input/output) P21 (input/output) P20 (input/output)
Figure 7.8 Pin Functions in Mode 7 (Port 2)
Rev.2.00 Mar. 22, 2007 Page 141 of 684 REJ09B0352-0200
7. I/O Ports
7.3.4
Input Pull-Up Transistors
Port 2 has built-in MOS input pull-up transistors that can be controlled by software. These input pull-up transistors can be turned on and off individually. When a P2PCR bit is set to 1 and the corresponding P2DDR bit is cleared to 0, the input pull-up transistor is turned on. The input pull-up transistors are turned off by a reset and in hardware standby mode. In software standby mode they retain their previous state. Table 7.4 summarizes the states of the input pull-up transistors in each mode. Table 7.4
Mode 1 3 5 6 7
Input Pull-Up Transistor States (Port 2)
Reset Off Off Hardware Standby Mode Off Off Software Standby Mode Off On/off Other Modes Off On/off
Legend Off: The input pull-up transistor is always off. On/off: The input pull-up transistor is on if P2PCR = 1 and P2DDR = 0. Otherwise, it is off.
Rev.2.00 Mar. 22, 2007 Page 142 of 684 REJ09B0352-0200
7. I/O Ports
7.4
7.4.1
Port 3
Overview
Port 3 is an 8-bit input/output port with the pin configuration shown in figure 7.9. Port 3 is a data bus in modes 1, 3, 5, and 6 (expanded modes) and a generic input/output port in mode 7 (singlechip mode). Pins in port 3 can drive one TTL load and a 90-pF capacitive load. They can also drive a Darlington transistor pair.
Port 3 pins P37 /D7 P36 /D6 P35 /D5 Port 3 P34 /D4 P33 /D3 P32 /D2 P31 /D1 P30 /D0 Modes 1, 3, 5, and 6 D7 (input/output) D6 (input/output) D5 (input/output) D4 (input/output) D3 (input/output) D2 (input/output) D1 (input/output) D0 (input/output) Mode 7 P37 (input/output) P36 (input/output) P35 (input/output) P34 (input/output) P33 (input/output) P32 (input/output) P31 (input/output) P30 (input/output)
Figure 7.9 Port 3 Pin Configuration 7.4.2 Register Descriptions
Table 7.5 summarizes the registers of port 3. Table 7.5
Address* H'FFC4 H'FFC6 Note: *
Port 3 Registers
Name Port 3 data direction register Port 3 data register Lower 16 bits of the address. Abbreviation P3DDR P3DR R/W W R/W Initial Value H'00 H'00
Rev.2.00 Mar. 22, 2007 Page 143 of 684 REJ09B0352-0200
7. I/O Ports
Port 3 Data Direction Register (P3DDR): P3DDR is an 8-bit write-only register that can select input or output for each pin in port 3.
Bit Initial value Read/Write 7 0 W 6 0 W 5 0 W 4 0 W 3 0 W 2 0 W 1 0 W 0 0 W
P3 7 DDR P3 6 DDR P3 5 DDR P3 4 DDR P3 3 DDR P3 2 DDR P3 1 DDR P3 0 DDR
Port 3 data direction 7 to 0 These bits select input or output for port 3 pins
Modes 1, 3, 5, and 6: Port 3 functions as a data bus. P3DDR is ignored. Mode 7: Port 3 functions as an input/output port. A pin in port 3 becomes an output pin if the corresponding P3DDR bit is set to 1, and an input pin if this bit is cleared to 0. P3DDR is a write-only register. Its value cannot be read. All bits return 1 when read. P3DDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. If a P3DDR bit is set to 1, the corresponding pin maintains its output state in software standby mode. Port 3 Data Register (P3DR): P3DR is an 8-bit readable/writable register that stores data for pins P37 to P30.
Bit Initial value Read/Write 7 P3 7 0 R/W 6 P3 6 0 R/W 5 P3 5 0 R/W 4 P3 4 0 R/W 3 P3 3 0 R/W 2 P3 2 0 R/W 1 P3 1 0 R/W 0 P3 0 0 R/W
Port 3 data 7 to 0 These bits store data for port 3 pins
When a bit in P3DDR is set to 1, if port 3 is read the value of the corresponding P3DR bit is returned directly, regardless of the actual state of the pin. When a bit in P3DDR is cleared to 0, if port 3 is read the corresponding pin level is read. P3DR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it retains its previous setting.
Rev.2.00 Mar. 22, 2007 Page 144 of 684 REJ09B0352-0200
7. I/O Ports
7.4.3
Pin Functions in Each Mode
The pin functions of port 3 differ between modes 1, 3, 5, and 6 and mode 7. The pin functions in each mode are described below. Modes 1, 3, 5, and 6: All pins of port 3 automatically become data input/output pins. Figure 7.10 shows the pin functions in modes 1, 3, 5, and 6.
D7 (input/output) D6 (input/output) D5 (input/output) Port 3 D4 (input/output) D3 (input/output) D2 (input/output) D1 (input/output) D0 (input/output)
Figure 7.10 Pin Functions in Modes 1, 3, 5, and 6 (Port 3) Mode 7: Input or output can be selected separately for each pin in port 3. A pin becomes an output pin if the corresponding P3DDR bit is set to 1, and an input pin if this bit is cleared to 0. Figure 7.11 shows the pin functions in mode 7.
P3 7 (input/output) P3 6 (input/output) P3 5 (input/output) Port 3 P3 4 (input/output) P3 3 (input/output) P3 2 (input/output) P3 1 (input/output) P3 0 (input/output)
Figure 7.11 Pin Functions in Mode 7 (Port 3)
Rev.2.00 Mar. 22, 2007 Page 145 of 684 REJ09B0352-0200
7. I/O Ports
7.5
7.5.1
Port 5
Overview
Port 5 is a 4-bit input/output port with the pin configuration shown in figure 7.12. The pin functions differ depending on the operating mode. In modes 1, 3 (expanded modes with on-chip ROM disabled), port 5 consists of address output pins (A19 to A16). In modes 5 and 6 (expanded modes with on-chip ROM enabled), settings in the port 5 data direction register (P5DDR) designate pins for address bus output (A19 to A16) or generic input. In mode 7 (single-chip mode), port 5 is a generic input/output port. Port 5 has software-programmable built-in pull-up transistors. Port 5 can drive one TTL load and a 90-pF capacitive load. They can also drive an LED or a Darlington transistor pair.
Port 5 pins P53 /A 19 Port 5 P52 /A 18 P51 /A 17 P50 /A 16 Modes 1, 3 A19 (output) A18 (output) A17 (output) A16 (output) Modes 5 and 6 P5 3 (input)/A19 (output) P5 2 (input)/A18 (output) P5 1 (input)/A17 (output) P5 0 (input)/A16 (output) Mode 7 P5 3 (input/output) P5 2 (input/output) P5 1 (input/output) P5 0 (input/output)
Figure 7.12 Port 5 Pin Configuration 7.5.2 Register Descriptions
Table 7.6 summarizes the registers of port 5. Table 7.6 Port 5 Registers
Initial Value Address* H'FFC8 H'FFCA H'FFDB Note: * Name Port 5 data direction register Port 5 data register Abbreviation P5DDR P5DR R/W W R/W R/W Modes 1 and 3 H'FF H'F0 H'F0 Modes 5 to 7 H'F0 H'F0 H'F0
Port 5 input pull-up P5PCR control register Lower 16 bits of the address.
Rev.2.00 Mar. 22, 2007 Page 146 of 684 REJ09B0352-0200
7. I/O Ports
Port 5 Data Direction Register (P5DDR): P5DDR is an 8-bit write-only register that can select input or output for each pin in port 5.
Bit Modes Initial value 1 and 3 Read/Write Modes Initial value 5 to 7 Read/Write 7 -- 1 -- 1 -- 6 -- 1 -- 1 -- Reserved bits 5 -- 1 -- 1 -- 4 -- 1 -- 1 -- 3 1 -- 0 W 2 1 -- 0 W 1 1 -- 0 W 0 1 -- 0 W
P5 3 DDR P5 2 DDR P5 1 DDR P5 0 DDR
Port 5 data direction 3 to 0 These bits select input or output for port 5 pins
P5DDR is initialized to H'F0 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. If a P5DDR bit is set to 1, the corresponding pin maintains its output state in software standby mode. Port 5 Data Register (P5DR): P5DR is an 8-bit readable/writable register that stores data for pins P53 to P50.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 P5 3 0 R/W 2 P5 2 0 R/W 1 P5 1 0 R/W 0 P5 0 0 R/W
Reserved bits
Port 5 data 3 to 0 These bits store data for port 5 pins
When a bit in P5DDR is set to 1, if port 5 is read the value of the corresponding P5DR bit is returned directly, regardless of the actual state of the pin. When a bit in P5DDR is cleared to 0, if port 5 is read the corresponding pin level is read. Bits P57 to P54 are reserved. They cannot be modified and are always read as 1. P5DR is initialized to H'F0 by a reset and in hardware standby mode. In software standby mode it retains its previous setting.
Rev.2.00 Mar. 22, 2007 Page 147 of 684 REJ09B0352-0200
7. I/O Ports
Port 5 Input Pull-Up Control Register (P5PCR): P5PCR is an 8-bit readable/writable register that controls the MOS input pull-up transistors in port 5.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 0 R/W 2 0 R/W 1 0 R/W 0 0 R/W
P5 3 PCR P5 2 PCR P5 1 PCR P5 0 PCR
Reserved bits
Port 5 input pull-up control 3 to 0 These bits control input pull-up transistors built into port 5
When a P5DDR bit is cleared to 0 (selecting generic input) in modes 5 to 7, if the corresponding bit from P53PCR to P50PCR is set to 1, the input pull-up transistor is turned on. P5PCR is initialized to H'F0 by a reset and in hardware standby mode. In software standby mode it retains its previous setting.
Rev.2.00 Mar. 22, 2007 Page 148 of 684 REJ09B0352-0200
7. I/O Ports
7.5.3
Pin Functions in Each Mode
The pin functions differ between mode 1, 3 (expanded modes with on-chip ROM disabled), modes 5 and 6 (expanded modes with on-chip ROM enabled), and mode 7 (single-chip mode). The pin functions in each mode are described below. Modes 1 and 3: Address output can be selected for each pin in port 5. Figure 7.13 shows the pin functions in modes 1 and 3.
A 19 (output) Port 5 A 18 (output) A 17 (output) A 16 (output)
Figure 7.13 Pin Functions in Modes 1 and 3 (Port 5) Modes 5 and 6: Address output or generic input can be selected for each pin in port 5. A pin becomes an address output pin if the corresponding P5DDR bit is set to 1, and a generic input pin if this bit is cleared to 0. Following a reset, all pins are input pins. To use a pin for address output, its P5DDR must be set to 1. Figure 7.14 shows the pin functions in modes 5 and 6.
When P5DDR = 1 A 19 (output) Port 5 A 18 (output) A 17 (output) A 16 (output) When P5DDR = 0 P5 3 (input) P5 2 (input) P5 1 (input) P5 0 (input)
Figure 7.14 Pin Functions in Modes 5 and 6 (Port 5) Mode 7: Input or output can be selected separately for each pin in port 5. A pin becomes an output pin if the corresponding P5DDR bit is set to 1, and an input pin if this bit is cleared to 0. Figure 7.15 shows the pin functions in mode 7.
Rev.2.00 Mar. 22, 2007 Page 149 of 684 REJ09B0352-0200
7. I/O Ports
P5 3 (input/output) Port 5 P5 2 (input/output) P5 1 (input/output) P5 0 (input/output)
Figure 7.15 Pin Functions in Mode 7 (Port 5) 7.5.4 Input Pull-Up Transistors
Port 5 has built-in MOS input pull-up transistors that can be controlled by software. These input pull-up transistors can be turned on and off individually. When a P5PCR bit is set to 1 and the corresponding P5DDR bit is cleared to 0, the input pull-up transistor is turned on. The input pull-up transistors are turned off by a reset and in hardware standby mode. In software standby mode they retain their previous state. Table 7.7 summarizes the states of the input pull-up transistors in each mode. Table 7.7
Mode 1 3 5 6 7
Input Pull-Up Transistor States (Port 5)
Reset Off Off Hardware Standby Mode Off Off Software Standby Mode Off On/off Other Modes Off On/off
Legend Off: The input pull-up transistor is always off. On/off: The input pull-up transistor is on if P5PCR = 1 and P5DDR = 0. Otherwise, it is off.
Rev.2.00 Mar. 22, 2007 Page 150 of 684 REJ09B0352-0200
7. I/O Ports
7.6
7.6.1
Port 6
Overview
Port 6 is a 4-bit input/output port that is also used for input and output of bus control signals (WR, RD, AS, and WAIT). Figure 7.16 shows the pin configuration of port 6. In modes 1, 3, 5, and 6 the pin functions are WR, RD, AS, and P60/WAIT. In mode 7, port 6 is a generic input/output port. Pins in port 6 can drive one TTL load and a 90-pF capacitive load. They can also drive a Darlington transistor pair.
Port 6 pins P6 5 / WR Port 6 P6 4 / RD P6 3 / AS P6 0 / WAIT
Modes 1, 3, 5 and 6 WR (output) RD (output) AS (output) P60 (input/output)/WAIT (input)
Mode 7 P6 5 (input/output) P6 4 (input/output) P6 3 (input/output) P6 0 (input/output)
Figure 7.16 Port 6 Pin Configuration 7.6.2 Register Descriptions
Table 7.8 summarizes the registers of port 6.
Rev.2.00 Mar. 22, 2007 Page 151 of 684 REJ09B0352-0200
7. I/O Ports
Table 7.8
Port 6 Registers
Initial Value
Address* H'FFC9 H'FFCB Note: *
Name
Abbreviation
R/W W R/W
Modes 1, 3, 5, and 6 Mode 7 H'F8 H'80 H'80 H'80
Port 6 data P6DDR direction register Port 6 data register P6DR
Lower 16 bits of the address.
Port 6 Data Direction Register (P6DDR): P6DDR is an 8-bit write-only register that can select input or output for each pin in port 6.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 0 W 5 0 W 4 0 W 3 0 W 2 -- 0 W 1 -- 0 W 0 P6 0 DDR 0 W
P6 5 DDR P6 4 DDR P6 3 DDR
Reserved bits
Port 6 data direction 5 to 3, 0 These bits select input or output for port 6 pins
Bits 7, 6, 2, and 1 are reserved. P6DDR is a write-only register. Its value cannot be read. All bits return 1 when read. P6DDR is initialized to H'80 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. If a P6DDR bit is set to 1, the corresponding pin maintains its output state in software standby mode.
Rev.2.00 Mar. 22, 2007 Page 152 of 684 REJ09B0352-0200
7. I/O Ports
Port 6 Data Register (P6DR): P6DR is an 8-bit readable/writable register that stores data for pins P65 to P63 and P60.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 0 R/W 5 P6 5 0 R/W 4 P6 4 0 R/W 3 P6 3 0 R/W 2 -- 0 R/W 1 -- 0 R/W 0 P6 0 0 R/W
Reserved bits
Port 6 data 5 to 3, 0 These bits store data for port 6 pins
When a bit in P6DDR is set to 1, if port 6 is read the value of the corresponding P6DR bit is returned directly. When a bit in P6DDR is cleared to 0, if port 6 is read the corresponding pin level is read. Bits 7, 6, 2, and 1 are reserved. Bit 7 cannot be modified and always reads 1. Bits 6, 2, and 1 can be written and read, but cannot be used as ports. If bit 6, 2, or 1 in P6DDR is read while its value is 1, the value of the corresponding bit in P6DR will be read. If bit 6, 2, or 1 in P6DDR is read while its value is 0, it will always read 1. P6DR is initialized to H'80 by a reset and in hardware standby mode. In software standby mode it retains its previous setting.
Rev.2.00 Mar. 22, 2007 Page 153 of 684 REJ09B0352-0200
7. I/O Ports
7.6.3
Pin Functions in Each Mode
Modes 1, 3, 5, and 6: P65 to P63 function as bus control output pins. P60 is either a bus control input pin or generic input/output pin, functioning as an output pin when bit P60DDR is set to 1 and an input pin when this bit is cleared to 0. Figure 7.17 and table 7.9 indicate the pin functions in modes 1, 3, 5, and 6.
WR (output) Port 6 RD (output) AS (output) P60 (input/output)/WAIT (input)
Figure 7.17 Pin Functions in Modes 1, 3, 5, and 6 (Port 6)
Rev.2.00 Mar. 22, 2007 Page 154 of 684 REJ09B0352-0200
7. I/O Ports
Table 7.9
Pin P65/WR
Port 6 Pin Functions in Modes 1, 3, 5, and 6
Pin Functions and Selection Method Functions as follows regardless of P65DDR P65DDR Pin function 0 WR output 1
P64/RD
Functions as follows regardless of P64DDR P64DDR Pin function 0 RD output 1
P63/AS
Functions as follows regardless of P63DDR P63DDR Pin function 0 AS output 1
P60/WAIT
Bits WCE7 to WCE0 in WCER, bit WMS1 in WCR, and bit P60DDR select the pin function as follows WCER WMS1 P60DDR Pin function Note: * 0 P60 input Do not set bit P60DDR to 1. 0 1 P60 output All 1s 1 0* Not all 1s -- 0* WAIT input
Rev.2.00 Mar. 22, 2007 Page 155 of 684 REJ09B0352-0200
7. I/O Ports
Mode 7: Input or output can be selected separately for each pin in port 6. A pin becomes an output pin if the corresponding P6DDR bit is set to 1, and an input pin if this bit is cleared to 0. Figure 7.18 shows the pin functions in mode 7.
P6 5 (input/output) Port 6 P6 4 (input/output) P6 3 (input/output) P6 0 (input/output)
Figure 7.18 Pin Functions in Mode 7 (Port 6)
Rev.2.00 Mar. 22, 2007 Page 156 of 684 REJ09B0352-0200
7. I/O Ports
7.7
7.7.1
Port 7
Overview
Port 7 is an 8-bit input port that is also used for analog input to the A/D converter. The pin functions are the same in all operating modes. Figure 7.19 shows the pin configuration of port 7.
Port 7 pins P77 (input)/AN 7 (input) P76 (input)/AN 6 (input) P75 (input)/AN 5 (input) Port 7 P74 (input)/AN 4 (input) P73 (input)/AN 3 (input) P72 (input)/AN 2 (input) P71 (input)/AN 1 (input) P70 (input)/AN 0 (input)
Figure 7.19 Port 7 Pin Configuration 7.7.2 Register Description
Table 7.10 summarizes the port 7 register. Port 7 is an input-only port, so it has no data direction register. Table 7.10 Port 7 Data Register
Address* H'FFCE Note: * Name Port 7 data register Lower 16 bits of the address. Abbreviation P7DR R/W R Initial Value Undetermined
Rev.2.00 Mar. 22, 2007 Page 157 of 684 REJ09B0352-0200
7. I/O Ports
Port 7 Data Register (P7DR)
Bit Initial value Read/Write 7 P77 --* R 6 P76 --* R 5 P75 --* R 4 P74 --* R 3 P73 --* R 2 P72 --* R 1 P71 --* R 0 P70 --* R
Note: * Determined by pins P77 to P70.
When port 7 is read, the pin levels are always read.
Rev.2.00 Mar. 22, 2007 Page 158 of 684 REJ09B0352-0200
7. I/O Ports
7.8
7.8.1
Port 8
Overview
Port 8 is a 2-bit input/output port that is also used for IRQ1 and IRQ0 input. Figure 7.20 shows the pin configuration of port 8. Pin P80 functions as input/output pin or as an IRQ0 input pin. Pins P81 function as either input pins or IRQ1 input pins in modes 1, 3, 5, and 6, and as input/output pins or IRQ1 input pins in mode 7. Pins in port 8 can drive one TTL load and a 90-pF capacitive load. They can also drive a Darlington transistor pair. Pins P81 and P80 have Schmitt-trigger inputs.
Port 8 pins
Modes 1, 3, 5, and 6
Mode 7
Port 8
P81/IRQ1 P80/IRQ0
P81 (input)/IRQ1 (input)
P81 (input/output)/IRQ1 (input)
P80 (input/output)/IRQ0 (input) P80 (input/output)/IRQ0 (input)
Figure 7.20 Port 8 Pin Configuration 7.8.2 Register Descriptions
Table 7.11 summarizes the registers of port 8. Table 7.11 Port 8 Registers
Address* H'FFCD H'FFCF Note: * Name Port 8 data direction register Port 8 data register Lower 16 bits of the address. Abbreviation P8DDR P8DR R/W W R/W Initial Value H'E0 H'E0
Rev.2.00 Mar. 22, 2007 Page 159 of 684 REJ09B0352-0200
7. I/O Ports
Port 8 Data Direction Register (P8DDR): P8DDR is an 8-bit write-only register that can select input or output for each pin in port 8.
7 Bit Initial value Read/Write -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 0 W 3 -- 0 W 2 -- 0 W 1 0 W 0 0 W
P8 1 DDR P8 0 DDR
Reserved bits
Port 8 data direction 1 and 0 These bits select input or output for port 8 pins
P8DDR is initialized to H'E0 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. If a P8DDR bit is set to 1, the corresponding pin maintains its output state in software standby mode. Port 8 Data Register (P8DR): P8DR is an 8-bit readable/writable register that stores data for pins P81 to P80.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 0 R/W 3 -- 0 R/W 2 -- 0 R/W 1 P8 1 0 R/W 0 P8 0 0 R/W
Reserved bits
Port 8 data 1 and 0 These bits store data for port 8 pins
When a bit in P8DDR is set to 1, if port 8 is read the value of the corresponding P8DR bit is returned directly. When a bit in P8DDR is cleared to 0, if port 8 is read the corresponding pin level is read. Bits 7 to 2 are reserved. Bits 7 to 5 cannot be modified and always read 1. Bit 4, 3, and 2 can be written and read, but it cannot be used for port input or output. If bit 4, 3, and 2 of P8DDR is read while its value is 1, bit 4, 3 and 2 of P8DR is read directly. If bit 4, 3, and 2 of P8DDR is read while its value is 0, it always reads 1. P8DR is initialized to H'E0 by a reset and in hardware standby mode. In software standby mode it retains its previous setting.
Rev.2.00 Mar. 22, 2007 Page 160 of 684 REJ09B0352-0200
7. I/O Ports
7.8.3
Pin Functions
The port 8 pins are also used for IRQ1 and IRQ0. Table 7.12 describes the selection of pin functions. Table 7.12 Port 8 Pin Functions
Pin P81/IRQ1 Pin Functions and Selection Method Bit P81DDR selects the pin function as follows P81DDR Pin function 0 Modes 1, 3, 5, and 6 P81 input Illegal setting IRQ1 input P80/IRQ0 Bit P80DDR selects the pin function as follows P80DDR Pin function 0 P80 input IRQ0 input 1 P80 output 1 Mode 7 P81 output
Rev.2.00 Mar. 22, 2007 Page 161 of 684 REJ09B0352-0200
7. I/O Ports
7.9
7.9.1
Port 9
Overview
Port 9 is a 6-bit input/output port that is also used for input and output (TxD0, TxD1, RxD0, RxD1, SCK0, SCK1) by serial communication interface channels 0 and 1 (SCI0 and SCI1), and for IRQ5 and IRQ4 input. Port 9 has the same set of pin functions in all operating modes. Figure 7.21 shows the pin configuration of port 9. Pins in port 9 can drive one TTL load and a 30-pF capacitive load. They can also drive a Darlington transistor pair.
Port 9 pins P95 (input/output)/SCK 1 (input/output)/IRQ 5 (input) P94 (input/output)/SCK 0 (input/output)/IRQ 4 (input) Port 9 P93 (input/output)/RxD1 (input) P92 (input/output)/RxD0 (input) P91 (input/output)/TxD1 (output) P90 (input/output)/TxD0 (output)
Figure 7.21 Port 9 Pin Configuration 7.9.2 Register Descriptions
Table 7.13 summarizes the registers of port 9. Table 7.13 Port 9 Registers
Address* H'FFD0 H'FFD2 Note: * Name Port 9 data direction register Port 9 data register Lower 16 bits of the address. Abbreviation P9DDR P9DR R/W W R/W Initial Value H'C0 H'C0
Rev.2.00 Mar. 22, 2007 Page 162 of 684 REJ09B0352-0200
7. I/O Ports
Port 9 Data Direction Register (P9DDR): P9DDR is an 8-bit write-only register that can select input or output for each pin in port 9.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 0 W 4 0 W 3 0 W 2 0 W 1 0 W 0 0 W
P9 5 DDR P9 4 DDR P9 3 DDR P9 2 DDR P9 1 DDR P9 0 DDR
Reserved bits
Port 9 data direction 5 to 0 These bits select input or output for port 9 pins
A pin in port 9 becomes an output pin if the corresponding P9DDR bit is set to 1, and an input pin if this bit is cleared to 0. P9DDR is a write-only register. Its value cannot be read. All bits return 1 when read. P9DDR is initialized to H'C0 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. If a P9DDR bit is set to 1, the corresponding pin maintains its output state in software standby mode. Port 9 Data Register (P9DR): P9DR is an 8-bit readable/writable register that stores output data for pins P95 to P90.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 P9 5 0 R/W 4 P9 4 0 R/W 3 P9 3 0 R/W 2 P9 2 0 R/W 1 P9 1 0 R/W 0 P9 0 0 R/W
Reserved bits
Port 9 data 5 to 0 These bits store data for port 9 pins
When a bit in P9DDR is set to 1, if port 9 is read the value of the corresponding P9DR bit is returned. When a bit in P9DDR is cleared to 0, if port 9 is read the corresponding pin level is read. Bits 7 and 6 are reserved. They cannot be modified and are always read as 1. P9DR is initialized to H'C0 by a reset and in hardware standby mode. In software standby mode it retains its previous setting.
Rev.2.00 Mar. 22, 2007 Page 163 of 684 REJ09B0352-0200
7. I/O Ports
7.9.3
Pin Functions
The port 9 pins are also used for SCI input and output (TxD, RxD, SCK), and for IRQ5 and IRQ4 input. Table 7.14 describes the selection of pin functions. Table 7.14 Port 9 Pin Functions
Pin P95/SCK1/ IRQ5 Pin Functions and Selection Method Bit C/A in SMR of SCI1, bits CKE0 and CKE1 in SCR of SCI1, and bit P95DDR select the pin function as follows CKE1 C/A CKE0 P95DDR Pin function 0 P95 input 0 1 P95 output 0 1 -- SCK1 output 0 1 -- -- SCK1 output 1 -- -- -- SCK1 input
IRQ5 input P94/SCK0/ IRQ4 Bit C/A in SMR of SCI0, bits CKE0 and CKE1 in SCR of SCI, and bit P94DDR select the pin function as follows CKE1 C/A CKE0 P94DDR Pin function 0 P94 input 0 1 P94 output 0 1 -- SCK0 output 0 1 -- -- SCK0 output 1 -- -- -- SCK0 input
IRQ4 input P93/RxD1 Bit RE in SCR of SCI1 and bit P93DDR select the pin function as follows RE P93DDR Pin function 0 P93 input 0 1 P93 output 1 -- RxD1 input
Rev.2.00 Mar. 22, 2007 Page 164 of 684 REJ09B0352-0200
7. I/O Ports Pin P92/RxD0 Pin Functions and Selection Method Bit RE in SCR of SCI0, bit SMIF in SCMR, and bit P92DDR select the pin function as follows SMIF RE P92DDR Pin function 0 P92 input 0 1 P92 output 0 1 -- RxD0 input 1 -- -- RxD0 input
P91/TxD1
Bit TE in SCR of SCI1 and bit P91DDR select the pin function as follows TE P91DDR Pin function 0 P91 input 0 1 P91 output 1 -- TxD1 output
P90/TxD0
Bit TE in SCR of SCI0, bit SMIF in SCMR, and bit P90DDR select the pin function as follows SMIF TE P90DDR Pin function 0 P90 input 0 1 P90 output 0 1 -- TxD0 output 1 -- -- TxD0 output*
Note: * Functions as the TxD0 output pin, but there are two states : one in which the pin is driven, and another in which the pin is at high impedance.
Rev.2.00 Mar. 22, 2007 Page 165 of 684 REJ09B0352-0200
7. I/O Ports
7.10
7.10.1
Port A
Overview
Port A is an 8-bit input/output port that is also used for output (TP7 to TP0) from the programmable timing pattern controller (TPC), input and output (TIOCB2, TIOCA2, TIOCB1, TIOCA1, TIOCB0, TIOCA0, TCLKD, TCLKC, TCLKB, TCLKA) by the 16-bit integrated timer unit (ITU), and address output (A23 to A20). Figure 7.22 shows the pin configuration of port A. Pins in port A can drive one TTL load and a 30-pF capacitive load. They can also drive a Darlington transistor pair. Port A has Schmitt-trigger inputs.
Port A pins PA7 /TP7/TIOCB 2 /A 20 PA6 /TP6/TIOCA 2 /A 21 PA5 /TP5/TIOCB 1 /A 22 PA4 /TP4/TIOCA 1 /A 23 Port A PA3 /TP3/TIOCB 0 /TCLKD PA2 /TP2/TIOCA 0 /TCLKC PA1 /TP1/TCLKB PA0 /TP0/TCLKA Modes 1, 5 and 7 PA 7 (input/output)/TP7 (output)/TIOCB 2 (input/output) PA 6 (input/output)/TP6 (output)/TIOCA 2 (input/output) PA 5 (input/output)/TP5 (output)/TIOCB 1 (input/output) PA 4 (input/output)/TP4 (output)/TIOCA 1 (input/output) PA 3 (input/output)/TP3 (output)/TIOCB 0 (input/output)/TCLKD (input) PA 2 (input/output)/TP2 (output)/TIOCA 0 (input/output)/TCLKC (input) PA 1 (input/output)/TP1 (output)/TCLKB (input) PA 0 (input/output)/TP0 (output)/TCLKA (input)
Modes 3 and 6 A 20 (output) PA 6 (input/output)/TP6 (output)/TIOCA 2 (input/output) /A 21 (output) PA 5 (input/output)/TP5 (output)/TIOCB 1 (input/output) /A 22 (output) PA 4 (input/output)/TP4 (output)/TIOCA 1 (input/output) /A 23 (output) PA 3 (input/output)/TP3 (output)/TIOCB 0 (input/output)/TCLKD (input) PA 2 (input/output)/TP2 (output)/TIOCA 0 (input/output)/TCLKC (input) PA 1 (input/output)/TP1 (output)/TCLKB (input) PA 0 (input/output)/TP0 (output)/TCLKA (input)
Figure 7.22 Port A Pin Configuration
Rev.2.00 Mar. 22, 2007 Page 166 of 684 REJ09B0352-0200
7. I/O Ports
7.10.2
Register Descriptions
Table 7.15 summarizes the registers of port A. Table 7.15 Port A Registers
Initial Value Address* H'FFD1 H'FFD3 Note: * Name Abbreviation R/W W R/W Modes 1, 5, and 7 H'00 H'00 Modes 3 and 6 H'80 H'00
Port A data direction PADDR register Port A data register PADR Lower 16 bits of the address.
Port A Data Direction Register (PADDR): PADDR is an 8-bit write-only register that can select input or output for each pin in port A. The corresponding PADDR bit should also be set when a pin is used as a TPC output.
7 Bit Modes 3 and 6 Modes 1, 5, and 7 Initial value Read/Write Initial value Read/Write 1 -- 0 W 6 0 W 0 W 5 0 W 0 W 4 0 W 0 W 3 0 W 0 W 2 0 W 0 W 1 0 W 0 W 0 0 W 0 W
PA7 DDR PA6 DDR PA5 DDR PA4 DDR PA3 DDR PA2 DDR PA1 DDR PA0 DDR
Port A data direction 7 to 0 These bits select input or output for port A pins
A pin in port A becomes an output pin if the corresponding PADDR bit is set to 1, and an input pin if this bit is cleared to 0. However, in modes 3 and 6, PA7 DDR is fixed at 1, and PA7 functions as an address output pin. PADDR is a write-only register. Its value cannot be read. All bits return 1 when read. PADDR is initialized to H'00 in modes 1, 5 and 7 and to H'80 in modes 3 and 6 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. If a PADDR bit is set to 1, the corresponding pin maintains its output state in software standby mode.
Rev.2.00 Mar. 22, 2007 Page 167 of 684 REJ09B0352-0200
7. I/O Ports
Port A Data Register (PADR): PADR is an 8-bit readable/writable register that stores data for pins PA7 to PA0.
Bit Initial value Read/Write 7 PA 7 0 R/W 6 PA 6 0 R/W 5 PA 5 0 R/W 4 PA 4 0 R/W 3 PA 3 0 R/W 2 PA 2 0 R/W 1 PA 1 0 R/W 0 PA 0 0 R/W
Port A data 7 to 0 These bits store data for port A pins
When a bit in PADDR is set to 1, if port A is read the value of the corresponding PADR bit is returned directly. When a bit in PADDR is cleared to 0, if port A is read the corresponding pin level is read. PADR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. When port A pins are used for TPC output, PADR stores output data for TPC output groups 0 and 1. If a bit in the next data enable register (NDERA) is set to 1, the corresponding PADR bit cannot be written. In this case, PADR can be updated only when data is transferred from NDRA.
Rev.2.00 Mar. 22, 2007 Page 168 of 684 REJ09B0352-0200
7. I/O Ports
7.10.3
Pin Functions
The port A pins are also used for TPC output (TP7 to TP0), ITU input/output (TIOCB2 to TIOCB0, TIOCA2 to TIOCA0) and input (TCLKD, TCLKC, TCLKB, TCLKA), and as address bus pins (A23 to A20). Table 7.16 describes the selection of pin functions. Table 7.16 Port A Pin Functions
Pin PA7/TP7/ TIOCB2/A20 Pin Functions and Selection Method The mode setting, ITU channel 2 settings (bit PWM2 in TMDR and bits IOB2 to IOB0 in TIOR2), bit NDER7 in NDERA, and bit PA7DDR in PADDR select the pin function as follows Mode ITU channel 2 settings PA7DDR NDER7 Pin function (1) in table below -- -- TIOCB2 output 0 -- PA7 input 1, 5 and 7 (2) in table below 1 0 PA7 output 1 1 TP7 output 3 and 6 -- -- -- A20 output
TIOCB2 input* Note: * TIOCB2 input when IOB2 = 1 and PWM2 = 0. (2) 0 0 0 0 1 1 -- (1) (2) 1 -- -- ITU channel 2 settings IOB2 IOB1 IOB0
Rev.2.00 Mar. 22, 2007 Page 169 of 684 REJ09B0352-0200
7. I/O Ports Pin PA6/TP6/ TIOCA2/ A21 Pin Functions and Selection Method The mode setting, bit A21E in BRCR, ITU channel 2 settings (bit PWM2 in TMDR and bits IOA2 to IOA0 in TIOR2), bit NDER6 in NDERA, and bit PA6DDR in PADDR select the pin function as follows Mode A21E ITU channel 2 settings PA6DDR NDER6 Pin function Note: * (1)in table below -- -- TIOCA2 output 0 -- PA6 input 1, 5 and 7 -- (2) in table below 1 0 1 1 (1) in table below -- -- 0 -- PA6 input 3 and 6 1 (2) in table below 1 0 1 1 0 --
-- --
PA6 TP6 TIOCA2 output output output
PA6 TP6 A21 output output output
TIOCA2 input* TIOCA2 input when IOA2 = 1. (2) (1) 0 0 0 0 0 1 1 -- 1 -- -- (2) ITU channel 2 settings PWM2 IOA2 IOA1 IOA0
TIOCA2 input*
(1) 1 -- -- --
Rev.2.00 Mar. 22, 2007 Page 170 of 684 REJ09B0352-0200
7. I/O Ports Pin PA5/TP5/ TIOCB1/ A22 Pin Functions and Selection Method The mode setting, bit A22E in BRCR, ITU channel 1 settings (bit PWM1 in TMDR and bits IOB2 to IOB0 in TIOR1), bit NDER5 in NDERA, and bit PA5DDR in PADDR select the pin function as follows Mode A22E ITU channel 1 settings PA5DDR NDER5 Pin function Note: * (1) in table below -- -- TIOCB1 output 0 -- PA5 input 1, 5 and 7 -- (2) in table below 1 0 1 1 (1) in table below -- -- 0 -- PA5 input 3 and 6 1 (2) in table below 1 0 1 1 0 --
-- --
PA5 TP5 TIOCB1 output output output
PA5 TP5 A22 output output output
TIOCB1 input* TIOCB1 input when IOB2 = 1 and PWM1 = 0. (2) 0 0 0 0 1 1 -- (1) ITU channel 1 settings IOB2 IOB1 IOB0
TIOCB1 input*
(2) 1 -- --
Rev.2.00 Mar. 22, 2007 Page 171 of 684 REJ09B0352-0200
7. I/O Ports Pin PA4/TP4/ TIOCA1/ A23 Pin Functions and Selection Method The mode setting, bit A23E in BRCR, ITU channel 1 settings (bit PWM1 in TMDR and bits IOA2 to IOA0 in TIOR1), bit NDER4 in NDERA, and bit PA4DDR in PADDR select the pin function as follows Mode A23E ITU channel 1 settings PA4DDR NDER4 Pin function Note: * (1) in table below -- -- TIOCA1 output 0 -- PA4 input 1, 5 and 7 -- (2) in table below 1 0 1 1 (1) in table below -- -- 0 -- PA4 input 3 and 6 1 (2) in table below 1 0 1 1 0 --
-- --
PA4 TP4 TIOCA1 output output output
PA4 TP4 A23 output output output
TIOCA1 input* TIOCA1 input when IOA2 = 1. (2) (1) 0 0 0 0 0 1 1 -- 1 -- -- (2) ITU channel 1 settings PWM1 IOA2 IOA1 IOA0
TIOCA1 input*
(1) 1 -- -- --
Rev.2.00 Mar. 22, 2007 Page 172 of 684 REJ09B0352-0200
7. I/O Ports Pin PA3/TP3/ TIOCB0/ TCLKD Pin Functions and Selection Method ITU channel 0 settings (bit PWM0 in TMDR and bits IOB2 to IOB0 in TIOR0), bits TPSC2 to TPSC0 in TCR4 to TCR0, bit NDER3 in NDERA, and bit PA3DDR in PADDR select the pin function as follows ITU channel 0 settings PA3DDR NDER3 Pin function (1) in table below -- -- TIOCB0 output 0 -- PA3 input (2) in table below 1 0 1 1
PA3 output TP3 output TIOCB0 input*
1
TCLKD input*
2
Notes: 1. TIOCB0 input when IOB2 = 1 and PWM0 = 0. 2. TCLKD input when TPSC2 = TPSC1 = TPSC0 = 1 in any of TCR4 to TCR0. ITU channel 0 settings IOB2 IOB1 IOB0 0 0 (2) 0 0 1 1 -- (1) (2) 1 -- --
Rev.2.00 Mar. 22, 2007 Page 173 of 684 REJ09B0352-0200
7. I/O Ports Pin PA2/TP2/ TIOCA0/ TCLKC Pin Functions and Selection Method ITU channel 0 settings (bit PWM0 in TMDR and bits IOA2 to IOA0 in TIOR0), bits TPSC2 to TPSC0 in TCR4 to TCR0, bit NDER2 in NDERA, and bit PA2DDR in PADDR select the pin function as follows ITU channel 0 settings PA2DDR NDER2 Pin function (1) in table below -- -- TIOCA0 output 0 -- PA2 input (2) in table below 1 0 1 1
PA2 output TP2 output TIOCA0 input*
1
TCLKC input*
2
Notes: 1. TIOCA0 input when IOA2 = 1. 2. TCLKC input when TPSC2 = TPSC1 = 1 and TPSC0 = 0 in any of TCR4 to TCR0. ITU channel 0 settings PWM0 IOA2 IOA1 IOA0 0 0 0 0 1 1 -- (2) (1) 0 1 -- -- (2) (1) 1 -- -- --
Rev.2.00 Mar. 22, 2007 Page 174 of 684 REJ09B0352-0200
7. I/O Ports Pin PA1/TP1/ TCLKB Pin Functions and Selection Method Bit NDER1 in NDERA and bit PA1DDR in PADDR select the pin function as follows PA1DDR NDER1 Pin function Note: PA0/TP0/ TCLKA * 0 -- PA1 input 1 0 PA1 output TCLKB input* TCLKB input when MDF = 1 in TMDR, or when TPSC2 = 1, TPSC1 = 0, and TPSC0 = 1 in any of TCR4 to TCR0. 1 1 TP1 output
Bit NDER0 in NDERA and bit PA0DDR in PADDR select the pin function as follows PA0DDR NDER0 Pin function Note: * 0 -- PA0 input 1 0 PA0 output TCLKA input* TCLKA input when MDF = 1 in TMDR, or when TPSC2 = 1 and TPSC1 = TPSC0 = 0 in any of TCR4 to TCR0. 1 1 TP0 output
Rev.2.00 Mar. 22, 2007 Page 175 of 684 REJ09B0352-0200
7. I/O Ports
7.11
7.11.1
Port B
Overview
Port B is an 7-bit input/output port that is also used for TPC output (TP15, TP13 to TP8), ITU input/output (TIOCB4, TIOCB3, TIOCA4, TIOCA3) and ITU output (TOCXB4, TOCXA4), and ADTRG input to the A/D converter. Port B has the same set of pin functions in all operating modes. Figure 7.23 shows the pin configuration of port B. Pins in port B can drive one TTL load and a 30-pF capacitive load. They can also drive an LED or a Darlington transistor pair. Pins PB3 to PB0 have Schmitt-trigger inputs.
Port B pins
PB 7 (input/output)/TP15 (output)/ADTRG (input) PB 5 (input/output)/TP13 (output)/TOCXB 4 (output) PB 4 (input/output)/TP12 (output)/TOCXA 4 (output) Port B PB 3 (input/output)/TP11 (output)/TIOCB 4 (input/output) PB 2 (input/output)/TP10 (output)/TIOCA 4 (input/output) PB 1 (input/output)/TP9 (output)/TIOCB 3 (input/output) PB 0 (input/output)/TP8 (output)/TIOCA 3 (input/output)
Figure 7.23 Port B Pin Configuration 7.11.2 Register Descriptions
Table 7.17 summarizes the registers of port B. Table 7.17 Port B Registers
Address* H'FFD4 H'FFD6 Note: * Name Abbreviation R/W W R/W Initial Value H'00 H'00
Port B data direction register PBDDR Port B data register Lower 16 bits of the address. PBDR
Rev.2.00 Mar. 22, 2007 Page 176 of 684 REJ09B0352-0200
7. I/O Ports
Port B Data Direction Register (PBDDR): PBDDR is an 8-bit write-only register that can select input or output for each pin in port B.
Bit Initial value Read/Write 7 PB7 DDR 0 W 6 -- 0 W 5 0 W 4 0 W 3 0 W 2 0 W 1 0 W 0 0 W
PB5 DDR PB4 DDR PB3 DDR PB2 DDR PB1 DDR PB0 DDR
Reserved bit
Port B data 7, 5 to 0 These bits select input or output for port B pins
A pin in port B becomes an output pin if the corresponding PBDDR bit is set to 1, and an input pin if this bit is cleared to 0. Bit 6 is reserved. PBDDR is a write-only register. Its value cannot be read. All bits return 1 when read. PBDDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. If a PBDDR bit is set to 1, the corresponding pin maintains its output state in software standby mode. Port B Data Register (PBDR): PBDR is an 8-bit readable/writable register that stores data for pins PB7, PB5 to PB0.
Bit Initial value Read/Write 7 PB 7 0 R/W 6 -- 0 R/W 5 PB 5 0 R/W 4 PB 4 0 R/W 3 PB 3 0 R/W 2 PB 2 0 R/W 1 PB 1 0 R/W 0 PB 0 0 R/W
Reserved bit
Port B data 7, 5 to 0 These bits store data for port B pins
When a bit in PBDDR is set to 1, if port B is read the value of the corresponding PBDR bit is returned directly. When a bit in PBDDR is cleared to 0, if port B is read the corresponding pin level is read. Bit 6 is reserved. Bit 6 can be written and read, but cannot be used for a port input or output. If bit 6 in PBDDR is read while its value is 1, the value of bit 6 in PBDR will be read directly. If bit 6 in PBDDR is read while its value is 0, it will always be read as 1.
Rev.2.00 Mar. 22, 2007 Page 177 of 684 REJ09B0352-0200
7. I/O Ports
PBDR is initialized to H'00 by a reset and in hardware standby mode. In software standby mode it retains its previous setting. When port B pins are used for TPC output, PBDR stores output data for TPC output groups 2 and 3. If a bit in the next data enable register (NDERB) is set to 1, the corresponding PBDR bit cannot be written. In this case, PBDR can be updated only when data is transferred from NDRB. 7.11.3 Pin Functions
The port B pins are also used for TPC output (TP15, TP13 to TP8), ITU input/output (TIOCB4, TIOCB3, TIOCA4, TIOCA3) and output (TOCXB4, TOCXA4), and ADTRG input. Table 7.18 describes the selection of pin functions.
Rev.2.00 Mar. 22, 2007 Page 178 of 684 REJ09B0352-0200
7. I/O Ports
Table 7.18 Port B Pin Functions
Pin PB7/ TP15/ ADTRG Pin Functions and Selection Method Bit TRGE in ADCR, bit NDER15 in NDERB and bit PB7DDR in PBDDR select the pin function as follows PB7DDR NDER15 Pin function Notes: * ADTRG input when TRGE = 1. 0 -- PB7 input 1 0 PB7 output ADTRG input* 1 1 TP15 output
PB5/ TP13/ TOCXB4
ITU channel 4 settings (bit CMD1 in TFCR and bit EXB4 in TOER), bit NDER13 in NDERB, and bit PB5DDR in PBDDR select the pin function as follows EXB4, CMD1 PB5DDR NDER13 Pin function 0 -- PB5 input
Not both 1 1 0 PB5 output 1 1 TP13 output
Both 1 -- -- TOCXB4 output
PB4/ TP12/ TOCXA4
ITU channel 4 settings (bit CMD1 in TFCR and bit EXA4 in TOER), bit NDER12 in NDERB, and bit PB4DDR in PBDDR select the pin function as follows EXA4, CMD1 PB4DDR NDER12 Pin function 0 -- PB4 input
Not both 1 1 0 PB4 output 1 1 TP12 output
Both 1 -- -- TOCXA4 output
Rev.2.00 Mar. 22, 2007 Page 179 of 684 REJ09B0352-0200
7. I/O Ports Pin PB3/ TP11/ TIOCB4 Pin Functions and Selection Method ITU channel 4 settings (bit PWM4 in TMDR, bit CMD1 in TFCR, bit EB4 in TOER, and bits IOB2 to IOB0 in TIOR4), bit NDER11 in NDERB, and bit PB3DDR in PBDDR select the pin function as follows ITU channel 4 settings PB3DDR NDER11 Pin function Note: * (1) in table below -- -- TIOCB4 output 0 -- PB3 input (2) in table below 1 0 PB3 output TIOCB4 input* TIOCB4 input when CMD1 = PWM4 = 0 and IOB2 = 1. ITU channel 4 settings EB4 CMD1 IOB2 IOB1 IOB0 1 1 TP11 output
(2) 0 -- -- -- --
(2)
(1) 1 0
(2)
(1)
1 0 1 -- 1 -- -- -- -- --
0 0 0
0 0 1
Rev.2.00 Mar. 22, 2007 Page 180 of 684 REJ09B0352-0200
7. I/O Ports Pin PB2/ TP10/ TIOCA4 Pin Functions and Selection Method ITU channel 4 settings (bit CMD1 in TFCR, bit EA4 in TOER, bit PWM4 in TMDR, and bits IOA2 to IOA0 in TIOR4), bit NDER10 in NDERB, and bit PB2DDR in PBDDR select the pin function as follows ITU channel 4 settings PB2DDR NDER10 Pin function Note: * (1) in table below -- -- TIOCA4 output 0 -- PB2 input (2) in table below 1 0 PB2 output TIOCA4 input* TIOCA4 input when CMD1 = PWM4 = 0 and IOA2 = 1. ITU channel 4 settings EA4 CMD1 PWM4 IOA2 IOA1 IOA0 1 1 TP10 output
(2) 0 -- -- -- -- --
(2)
(1) 1 0 0
(2)
(1)
1 1 -- -- -- --
0 0 0
0 0 1
0 1 --
1 -- --
-- -- --
Rev.2.00 Mar. 22, 2007 Page 181 of 684 REJ09B0352-0200
7. I/O Ports Pin PB1/TP9/ TIOCB3 Pin Functions and Selection Method ITU channel 3 settings (bit PWM3 in TMDR, bit CMD1 in TFCR, bit EB3 in TOER, and bits IOB2 to IOB0 in TIOR3), bit NDER9 in NDERB, and bit PB1DDR in PBDDR select the pin function as follows ITU channel 3 settings PB1DDR NDER9 Pin function Note: *
(1) in table below -- -- TIOCB3 output 0 -- PB1 input
(2) in table below 1 0 PB1 output TIOCB3 input* 1 1 TP9 output
TIOCB3 input when CMD1 = PWM3 = 0 and IOB2 = 1.
ITU channel 3 settings EB3 CMD1 IOB2 IOB1 IOB0
(2) 0 -- -- -- --
(2)
(1) 1 0
(2)
(1)
1 0 1 -- 1 -- -- -- -- --
0 0 0
0 0 1
Rev.2.00 Mar. 22, 2007 Page 182 of 684 REJ09B0352-0200
7. I/O Ports Pin PB0/TP8/ TIOCA3 Pin Functions and Selection Method ITU channel 3 settings (bit CMD1 in TFCR, bit EA3 in TOER, bit PWM3 in TMDR, and bits IOA2 to IOA0 in TIOR3), bit NDER8 in NDERB, and bit PB0DDR in PBDDR select the pin function as follows ITU channel 3 settings PB0DDR NDER8 Pin function Note: *
(1) in table below -- -- TIOCA3 output 0 -- PB0 input
(2) in table below 1 0 PB0 output TIOCA3 input* 1 1 TP8 output
TIOCA3 input when CMD1 = PWM3 = 0 and IOA2 = 1.
ITU channel 3 settings EA3 CMD1 PWM3 IOA2 IOA1 IOA0
(2) 0 -- -- -- -- --
(2)
(1) 1 0 0
(2)
(1)
1 1 -- -- -- --
0 0 0
0 0 1
0 1 --
1 -- --
-- -- --
Rev.2.00 Mar. 22, 2007 Page 183 of 684 REJ09B0352-0200
7. I/O Ports
Rev.2.00 Mar. 22, 2007 Page 184 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Section 8 16-Bit Integrated Timer Unit (ITU)
8.1 Overview
The H8/3022 Group has a built-in 16-bit integrated timer unit (ITU) with five 16-bit timer channels. 8.1.1 Features
ITU features are listed below. * Capability to process up to 12 pulse outputs or 10 pulse inputs * Ten general registers (GRs, two per channel) with independently-assignable output compare or input capture functions * Selection of eight counter clock sources for each channel: Internal clocks: , /2, /4, /8 External clocks: TCLKA, TCLKB, TCLKC, TCLKD * Five operating modes selectable in all channels: Waveform output by compare match Selection of 0 output, 1 output, or toggle output (only 0 or 1 output in channel 2) Input capture function Rising edge, falling edge, or both edges (selectable) Counter clearing function Counters can be cleared by compare match or input capture Synchronization Two or more timer counters (TCNTs) can be preset simultaneously, or cleared simultaneously by compare match or input capture. Counter synchronization enables synchronous register input and output. PWM mode PWM output can be provided with an arbitrary duty cycle. With synchronization, up to five-phase PWM output is possible * Phase counting mode selectable in channel 2 Two-phase encoder output can be counted automatically. * Three additional modes selectable in channels 3 and 4 Reset-synchronized PWM mode If channels 3 and 4 are combined, three-phase PWM output is possible with three pairs of complementary waveforms.
Rev.2.00 Mar. 22, 2007 Page 185 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Complementary PWM mode If channels 3 and 4 are combined, three-phase PWM output is possible with three pairs of non-overlapping complementary waveforms. Buffering Input capture registers can be double-buffered. Output compare registers can be updated automatically. * High-speed access via internal 16-bit bus The 16-bit timer counters, general registers, and buffer registers can be accessed at high speed via a 16-bit bus. * Fifteen interrupt sources Each channel has two compare match/input capture interrupts and an overflow interrupt. All interrupts can be requested independently. * Output triggering of programmable pattern controller (TPC) Compare match/input capture signals from channels 0 to 3 can be used as TPC output triggers. Table 8.1 summarizes the ITU functions. Table 8.1
Item Clock sources
ITU Functions
Channel 0 Channel 1 Channel 2 Channel 3 Channel 4
Internal clocks: , /2, /4, /8 External clocks: TCLKA, TCLKB, TCLKC, TCLKD, selectable independently GRA0, GRB0 GRA1, GRB1 GRA2, GRB2 GRA3, GRB3 GRA4, GRB4
General registers (output compare/ input capture registers) Buffer registers Input/output pins Output pins Counter clearing function
-- TIOCA0, TIOCB0 -- GRA0/GRB0 compare match or input capture
-- TIOCA1, TIOCB1 -- GRA1/GRB1 compare match or input capture
-- TIOCA2, TIOCB2 -- GRA2/GRB2 compare match or input capture
BRA3, BRB3 TIOCA3, TIOCB3 -- GRA3/GRB3 compare match or input capture
BRA4, BRB4 TIOCA4, TIOCB4 TOCXA4, TOCXB4 GRA4/GRB4 compare match or input capture
Rev.2.00 Mar. 22, 2007 Page 186 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Item Compare 0 match output 1 Toggle Channel 0 O O O O O O Channel 1 O O O O O O -- Channel 2 O O -- O O O -- Channel 3 O O O O O O O Channel 4 O O O O O O O
Input capture function Synchronization PWM mode
Reset-- synchronized PWM mode Complementary PWM mode Phase counting mode Buffering Interrupt sources -- -- -- Three sources * Compare match/input capture A0 * Compare match/input capture B0 * Legend O: Available --: Not available Overflow
-- -- -- Three sources * Compare match/input capture A1 * Compare match/input capture B1 * Overflow
-- O -- Three sources * Compare match/input capture A2 * Compare match/input capture B2 * Overflow
O -- O Three sources * Compare match/input capture A3 * Compare match/input capture B3 * Overflow
O -- O Three sources * Compare match/input capture A4 * Compare match/input capture B4 * Overflow
Rev.2.00 Mar. 22, 2007 Page 187 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.1.2
Block Diagrams
ITU Block Diagram (overall): Figure 8.1 is a block diagram of the ITU.
TCLKA to TCLKD , /2, /4, /8 TOCXA4, TOCXB4 TIOCA0 to TIOCA4 TIOCB0 to TIOCB4
Clock selector
IMIA0 to IMIA4 IMIB0 to IMIB4 OVI0 to OVI4
Control logic
TOER
16-bit timer channel 4
16-bit timer channel 3
16-bit timer channel 2
16-bit timer channel 1
16-bit timer channel 0
TOCR TSTR TSNC TMDR TFCR
Module data bus Legend TOER: TOCR: TSTR: TSNC: TMDR: TFCR:
Timer output master enable register (8 bits) Timer output control register (8 bits) Timer start register (8 bits) Timer synchro register (8 bits) Timer mode register (8 bits) Timer function control register (8 bits)
Figure 8.1 ITU Block Diagram (Overall)
Rev.2.00 Mar. 22, 2007 Page 188 of 684 REJ09B0352-0200
Internal data bus
Bus interface
8. 16-Bit Integrated Timer Unit (ITU)
Block Diagram of Channels 0 and 1: ITU channels 0 and 1 are functionally identical. Both have the structure shown in figure 8.2.
TCLKA to TCLKD , /2, /4, /8 Clock selector Control logic Comparator
TIOCA0 TIOCB0 IMIA0 IMIB0 OVI0
TCNT
TIOR
TIER
GRA
GRB
TCR
Module data bus Legend TCNT: GRA, GRB: TCR: TIOR: TIER: TSR:
Timer counter (16 bits) General registers A and B (input capture/output compare registers) (16 bits x 2) Timer control register (8 bits) Timer I/O control register (8 bits) Timer interrupt enable register (8 bits) Timer status register (8 bits)
Figure 8.2 Block Diagram of Channels 0 and 1 (for Channel 0)
Rev.2.00 Mar. 22, 2007 Page 189 of 684 REJ09B0352-0200
TSR
8. 16-Bit Integrated Timer Unit (ITU)
Block Diagram of Channel 2: Figure 8.3 is a block diagram of channel 2. This is the channel that provides only 0 output and 1 output.
TCLKA to TCLKD , /2, /4, /8 Clock selector Control logic Comparator
TIOCA2 TIOCB2 IMIA2 IMIB2 OVI2
TCNT2
TIOR2
TIER2
GRA2
GRB2
TCR2
Module data bus Legend Timer counter 2 (16 bits) TCNT2: GRA2, GRB2: General registers A2 and B2 (input capture/output compare registers) (16 bits x 2) Timer control register 2 (8 bits) TCR2: Timer I/O control register 2 (8 bits) TIOR2: Timer interrupt enable register 2 (8 bits) TIER2: Timer status register 2 (8 bits) TSR2:
Figure 8.3 Block Diagram of Channel 2
Rev.2.00 Mar. 22, 2007 Page 190 of 684 REJ09B0352-0200
TSR2
8. 16-Bit Integrated Timer Unit (ITU)
Block Diagrams of Channels 3 and 4: Figure 8.4 is a block diagram of channel 3. Figure 8.5 is a block diagram of channel 4.
TCLKA to TCLKD , /2, /4, /8 TIOCA3 TIOCB3 Control logic Comparator IMIA3 IMIB3 OVI3
Clock selector
TCNT3
TIOR3
TIER3
GRA3
GRB3
BRA3
BRB3
TCR3
Module data bus Legend Timer counter 3 (16 bits) TCNT3: GRA3, GRB3: General registers A3 and B3 (input capture/output compare registers) (16 bits x 2) BRA3, BRB3: Buffer registers A3 and B3 (input capture/output compare buffer registers) (16 bits x 2) Timer control register 3 (8 bits) TCR3: TIOR3: Timer I/O control register 3 (8 bits) TIER3: Timer interrupt enable register 3 (8 bits) TSR3: Timer status register 3 (8 bits)
Figure 8.4 Block Diagram of Channel 3
Rev.2.00 Mar. 22, 2007 Page 191 of 684 REJ09B0352-0200
TSR3
8. 16-Bit Integrated Timer Unit (ITU)
TCLKA to TCLKD , /2, /4, /8
Clock selector Control logic Comparator
TOCXA4 TOCXB4 TIOCA4 TIOCB4 IMIA4 IMIB4 OVI4
TCNT4
TIOR4
TIER4
GRA4
GRB4
BRA4
BRB4
TCR4
Module data bus Legend Timer counter 4 (16 bits) TCNT4: GRA4, GRB4: General registers A4 and B4 (input capture/output compare registers) (16 bits x 2) BRA4, BRB4: Buffer registers A4 and B4 (input capture/output compare buffer registers) (16 bits x 2) Timer control register 4 (8 bits) TCR4: TIOR4: Timer I/O control register 4 (8 bits) TIER4: Timer interrupt enable register 4 (8 bits) TSR4: Timer status register 4 (8 bits)
Figure 8.5 Block Diagram of Channel 4
Rev.2.00 Mar. 22, 2007 Page 192 of 684 REJ09B0352-0200
TSR4
8. 16-Bit Integrated Timer Unit (ITU)
8.1.3
Pin Configuration
Table 8.2 summarizes the ITU pins. Table 8.2
Channel Common
ITU Pins
Name Clock input A Clock input B Clock input C Clock input D Abbreviation TCLKA TCLKB TCLKC TCLKD TIOCA0 Input/ Output Input Input Input Input Input/ output Input/ output Input/ output Input/ output Input/ output Input/ output Input/ output Function External clock A input pin (phase-A input pin in phase counting mode) External clock B input pin (phase-B input pin in phase counting mode) External clock C input pin External clock D input pin GRA0 output compare or input capture pin PWM output pin in PWM mode GRB0 output compare or input capture pin
0
Input capture/output compare A0 Input capture/output compare B0
TIOCB0
1
Input capture/output compare A1 Input capture/output compare B1
TIOCA1
GRA1 output compare or input capture pin PWM output pin in PWM mode GRB1 output compare or input capture pin
TIOCB1
2
Input capture/output compare A2 Input capture/output compare B2
TIOCA2
GRA2 output compare or input capture pin PWM output pin in PWM mode GRB2 output compare or input capture pin
TIOCB2
3
Input capture/output compare A3 Input capture/output compare B3
TIOCA3
GRA3 output compare or input capture pin PWM output pin in PWM mode, complementary PWM mode, or reset-synchronized PWM mode GRB3 output compare or input capture pin PWM output pin in complementary PWM mode or reset-synchronized PWM mode
TIOCB3
Input/ output
Rev.2.00 Mar. 22, 2007 Page 193 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU) Abbreviation TIOCA4 Input/ Output Input/ output
Channel 4
Name Input capture/output compare A4 Input capture/output compare B4 Output compare XA4 Output compare XB4
Function GRA4 output compare or input capture pin PWM output pin in PWM mode, complementary PWM mode, or resetsynchronized PWM mode GRB4 output compare or input capture pin PWM output pin in complementary PWM mode or reset-synchronized PWM mode PWM output pin in complementary PWM mode or reset-synchronized PWM mode PWM output pin in complementary PWM mode or reset-synchronized PWM mode
TIOCB4
Input/ output
TOCXA4 TOCXB4
Output Output
Rev.2.00 Mar. 22, 2007 Page 194 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.1.4
Register Configuration
Table 8.3 summarizes the ITU registers. Table 8.3
Channel Common
ITU Registers
Address* H'FF60 H'FF61 H'FF62 H'FF63 H'FF90 H'FF91
1
Name Timer start register Timer synchro register Timer mode register Timer function control register Timer output master enable register Timer output control register Timer control register 0 Timer I/O control register 0 Timer interrupt enable register 0 Timer status register 0 Timer counter 0 (high) Timer counter 0 (low) General register A0 (high) General register A0 (low) General register B0 (high) General register B0 (low) Timer control register 1 Timer I/O control register 1 Timer interrupt enable register 1 Timer status register 1 Timer counter 1 (high) Timer counter 1 (low) General register A1 (high) General register A1 (low) General register B1 (high) General register B1 (low)
Abbreviation TSTR TSNC TMDR TFCR TOER TOCR TCR0 TIOR0 TIER0 TSR0 TCNT0H TCNT0L GRA0H GRA0L GRB0H GRB0L TCR1 TIOR1 TIER1 TSR1 TCNT1H TCNT1L GRA1H GRA1L GRB1H GRB1L
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/(W)* R/W R/W R/W R/W R/W R/W R/W R/W R/W R/(W)* R/W R/W R/W R/W R/W R/W
2 2
Initial Value H'E0 H'E0 H'80 H'C0 H'FF H'FF H'80 H'88 H'F8 H'F8 H'00 H'00 H'FF H'FF H'FF H'FF H'80 H'88 H'F8 H'F8 H'00 H'00 H'FF H'FF H'FF H'FF
0
H'FF64 H'FF65 H'FF66 H'FF67 H'FF68 H'FF69 H'FF6A H'FF6B H'FF6C H'FF6D
1
H'FF6E H'FF6F H'FF70 H'FF71 H'FF72 H'FF73 H'FF74 H'FF75 H'FF76 H'FF77
Rev.2.00 Mar. 22, 2007 Page 195 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU) Abbreviation TCR2 TIOR2 TIER2 TSR2 TCNT2H TCNT2L GRA2H GRA2L GRB2H GRB2L TCR3 TIOR3 TIER3 TSR3 TCNT3H TCNT3L GRA3H GRA3L GRB3H GRB3L BRA3H BRA3L BRB3H BRB3L Initial Value H'80 H'88 H'F8
2
Channel 2
Address* H'FF78 H'FF79 H'FF7A H'FF7B H'FF7C H'FF7D H'FF7E H'FF7F H'FF80 H'FF81
1
Name Timer control register 2 Timer I/O control register 2 Timer interrupt enable register 2 Timer status register 2 Timer counter 2 (high) Timer counter 2 (low) General register A2 (high) General register A2 (low) General register B2 (high) General register B2 (low) Timer control register 3 Timer I/O control register 3 Timer interrupt enable register 3 Timer status register 3 Timer counter 3 (high) Timer counter 3 (low) General register A3 (high) General register A3 (low) General register B3 (high) General register B3 (low) Buffer register A3 (high) Buffer register A3 (low) Buffer register B3 (high) Buffer register B3 (low)
R/W R/W R/W R/W R/(W)* R/W R/W R/W R/W R/W R/W R/W R/W R/W R/(W)* R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
2
H'F8 H'00 H'00 H'FF H'FF H'FF H'FF H'80 H'88 H'F8 H'F8 H'00 H'00 H'FF H'FF H'FF H'FF H'FF H'FF H'FF H'FF
3
H'FF82 H'FF83 H'FF84 H'FF85 H'FF86 H'FF87 H'FF88 H'FF89 H'FF8A H'FF8B H'FF8C H'FF8D H'FF8E H'FF8F
Rev.2.00 Mar. 22, 2007 Page 196 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU) Abbreviation TCR4 TIOR4 TIER4 TSR4 TCNT4H TCNT4L GRA4H GRA4L GRB4H GRB4L BRA4H BRA4L BRB4H BRB4L Initial Value H'80 H'88 H'F8
2
Channel 4
Address* H'FF92 H'FF93 H'FF94 H'FF95 H'FF96 H'FF97 H'FF98 H'FF99 H'FF9A H'FF9B H'FF9C H'FF9D H'FF9E H'FF9F
1
Name Timer control register 4 Timer I/O control register 4 Timer interrupt enable register 4 Timer status register 4 Timer counter 4 (high) Timer counter 4 (low) General register A4 (high) General register A4 (low) General register B4 (high) General register B4 (low) Buffer register A4 (high) Buffer register A4 (low) Buffer register B4 (high) Buffer register B4 (low)
R/W R/W R/W R/W R/(W)* R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
H'F8 H'00 H'00 H'FF H'FF H'FF H'FF H'FF H'FF H'FF H'FF
Notes: 1. The lower 16 bits of the address are indicated. 2. Only 0 can be written, to clear flags.
Rev.2.00 Mar. 22, 2007 Page 197 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.2
8.2.1
Register Descriptions
Timer Start Register (TSTR)
TSTR is an 8-bit readable/writable register that starts and stops the timer counter (TCNT) in channels 0 to 4.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- Reserved bits 5 -- 1 -- 4 STR4 0 R/W 3 STR3 0 R/W 2 STR2 0 R/W 1 STR1 0 R/W 0 STR0 0 R/W
Counter start 4 to 0 These bits start and stop TCNT4 to TCNT0
TSTR is initialized to H'E0 by a reset and in standby mode. Bits 7 to 5--Reserved: These bits cannot be modified and are always read as 1. Bit 4--Counter Start 4 (STR4): Starts and stops timer counter 4 (TCNT4).
Bit4 STR4 0 1 Description TCNT4 is halted TCNT4 is counting (Initial value)
Bit 3--Counter Start 3 (STR3): Starts and stops timer counter 3 (TCNT3).
Bit 3 STR3 0 1 Description TCNT3 is halted TCNT3 is counting (Initial value)
Bit 2--Counter Start 2 (STR2): Starts and stops timer counter 2 (TCNT2).
Bit 2 STR2 0 1 Description TCNT2 is halted TCNT2 is counting (Initial value)
Rev.2.00 Mar. 22, 2007 Page 198 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bit 1--Counter Start 1 (STR1): Starts and stops timer counter 1 (TCNT1).
Bit 1 STR1 0 1 Description TCNT1 is halted TCNT1 is counting (Initial value)
Bit 0--Counter Start 0 (STR0): Starts and stops timer counter 0 (TCNT0).
Bit 0 STR0 0 1 Description TCNT0 is halted TCNT0 is counting (Initial value)
8.2.2
Timer Synchro Register (TSNC)
TSNC is an 8-bit readable/writable register that selects whether channels 0 to 4 operate independently or synchronously. Channels are synchronized by setting the corresponding bits to 1.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- Reserved bits 5 -- 1 -- 4 SYNC4 0 R/W 3 SYNC3 0 R/W 2 SYNC2 0 R/W 1 SYNC1 0 R/W 0 SYNC0 0 R/W
Timer sync 4 to 0 These bits synchronize channels 4 to 0
TSNC is initialized to H'E0 by a reset and in standby mode. Bits 7 to 5--Reserved: These bits cannot be modified and are always read as 1. Bit 4--Timer Sync 4 (SYNC4): Selects whether channel 4 operates independently or synchronously.
Rev.2.00 Mar. 22, 2007 Page 199 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU) Bit 4 SYNC4 0 1
Description Channel 4's timer counter (TCNT4) operates independently TCNT4 is preset and cleared independently of other channels Channel 4 operates synchronously TCNT4 can be synchronously preset and cleared (Initial value)
Bit 3--Timer Sync 3 (SYNC3): Selects whether channel 3 operates independently or synchronously.
Bit 3 SYNC3 0 1 Description Channel 3's timer counter (TCNT3) operates independently TCNT3 is preset and cleared independently of other channels Channel 3 operates synchronously TCNT3 can be synchronously preset and cleared (Initial value)
Bit 2--Timer Sync 2 (SYNC2): Selects whether channel 2 operates independently or synchronously.
Bit 2 SYNC2 0 1 Description Channel 2's timer counter (TCNT2) operates independently TCNT2 is preset and cleared independently of other channels Channel 2 operates synchronously TCNT2 can be synchronously preset and cleared (Initial value)
Bit 1--Timer Sync 1 (SYNC1): Selects whether channel 1 operates independently or synchronously.
Bit 1 SYNC1 0 1 Description Channel 1's timer counter (TCNT1) operates independently TCNT1 is preset and cleared independently of other channels Channel 1 operates synchronously TCNT1 can be synchronously preset and cleared (Initial value)
Rev.2.00 Mar. 22, 2007 Page 200 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bit 0--Timer Sync 0 (SYNC0): Selects whether channel 0 operates independently or synchronously.
Bit 0 SYNC0 0 1 Description Channel 0's timer counter (TCNT0) operates independently TCNT0 is preset and cleared independently of other channels Channel 0 operates synchronously TCNT0 can be synchronously preset and cleared (Initial value)
Rev.2.00 Mar. 22, 2007 Page 201 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.2.3
Timer Mode Register (TMDR)
TMDR is an 8-bit readable/writable register that selects PWM mode for channels 0 to 4. It also selects phase counting mode and the overflow flag (OVF) setting conditions for channel 2.
Bit Initial value Read/Write 7 -- 1 -- 6 MDF 0 R/W 5 FDIR 0 R/W 4 PWM4 0 R/W 3 PWM3 0 R/W 2 PWM2 0 R/W 1 PWM1 0 R/W 0 PWM0 0 R/W
PWM mode 4 to 0 These bits select PWM mode for channels 4 to 0 Flag direction Selects the setting condition for the overflow flag (OVF) in timer status register 2 (TSR2) Phase counting mode flag Selects phase counting mode for channel 2 Reserved bit
TMDR is initialized to H'80 by a reset and in standby mode. Bit 7--Reserved: This bit cannot be modified and is always read as 1. Bit 6--Phase Counting Mode Flag (MDF): Selects whether channel 2 operates normally or in phase counting mode.
Bit 6 MDF 0 1 Description Channel 2 operates normally Channel 2 operates in phase counting mode (Initial value)
When MDF is set to 1 to select phase counting mode, timer counter 2 (TCNT2) operates as an up/down-counter and pins TCLKA and TCLKB become counter clock input pins. TCNT2 counts both rising and falling edges of TCLKA and TCLKB, and counts up or down as follows.
Rev.2.00 Mar. 22, 2007 Page 202 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Counting Direction TCLKA pin TCLKB pin Low Down-Counting High High Low High Up-Counting Low Low High
In phase counting mode channel 2 operates as above regardless of the external clock edges selected by bits CKEG1 and CKEG0 and the clock source selected by bits TPSC2 to TPSC0 in timer control register 2 (TCR2). Phase counting mode takes precedence over these settings. The counter clearing condition selected by the CCLR1 and CCLR0 bits in TCR2 and the compare match/input capture settings and interrupt functions of timer I/O control register 2 (TIOR2), timer interrupt enable register 2 (TIER2), and timer status register 2 (TSR2) remain effective in phase counting mode. Bit 5--Flag Direction (FDIR): Designates the setting condition for the overflow flag (OVF) in timer status register 2 (TSR2). The FDIR designation is valid in all modes in channel 2.
Bit 5 FDIR 0 1 Description OVF is set to 1 in TSR2 when TCNT2 overflows or underflows OVF is set to 1 in TSR2 when TCNT2 overflows (Initial value)
Bit 4--PWM Mode 4 (PWM4): Selects whether channel 4 operates normally or in PWM mode.
Bit 4 PWM4 0 1 Description Channel 4 operates normally Channel 4 operates in PWM mode (Initial value)
When bit PWM4 is set to 1 to select PWM mode, pin TIOCA4 becomes a PWM output pin. The output goes to 1 at compare match with general register A4 (GRA4), and to 0 at compare match with general register B4 (GRB4). If complementary PWM mode or reset-synchronized PWM mode is selected by bits CMD1 and CMD0 in the timer function control register (TFCR), the CMD1 and CMD0 setting takes precedence and the PWM4 setting is ignored.
Rev.2.00 Mar. 22, 2007 Page 203 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bit 3--PWM Mode 3 (PWM3): Selects whether channel 3 operates normally or in PWM mode.
Bit 3 PWM3 0 1 Description Channel 3 operates normally Channel 3 operates in PWM mode (Initial value)
When bit PWM3 is set to 1 to select PWM mode, pin TIOCA3 becomes a PWM output pin. The output goes to 1 at compare match with general register A3 (GRA3), and to 0 at compare match with general register B3 (GRB3). If complementary PWM mode or reset-synchronized PWM mode is selected by bits CMD1 and CMD0 in the timer function control register (TFCR), the CMD1 and CMD0 setting takes precedence and the PWM3 setting is ignored. Bit 2--PWM Mode 2 (PWM2): Selects whether channel 2 operates normally or in PWM mode.
Bit 2 PWM2 0 1 Description Channel 2 operates normally Channel 2 operates in PWM mode (Initial value)
When bit PWM2 is set to 1 to select PWM mode, pin TIOCA2 becomes a PWM output pin. The output goes to 1 at compare match with general register A2 (GRA2), and to 0 at compare match with general register B2 (GRB2). Bit 1--PWM Mode 1 (PWM1): Selects whether channel 1 operates normally or in PWM mode.
Bit 1 PWM1 0 1 Description Channel 1 operates normally Channel 1 operates in PWM mode (Initial value)
When bit PWM1 is set to 1 to select PWM mode, pin TIOCA1 becomes a PWM output pin. The output goes to 1 at compare match with general register A1 (GRA1), and to 0 at compare match with general register B1 (GRB1).
Rev.2.00 Mar. 22, 2007 Page 204 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bit 0--PWM Mode 0 (PWM0): Selects whether channel 0 operates normally or in PWM mode.
Bit PWM0 0 1 Description Channel 0 operates normally Channel 0 operates in PWM mode (Initial value)
When bit PWM0 is set to 1 to select PWM mode, pin TIOCA0 becomes a PWM output pin. The output goes to 1 at compare match with general register A0 (GRA0), and to 0 at compare match with general register B0 (GRB0). 8.2.4 Timer Function Control Register (TFCR)
TFCR is an 8-bit readable/writable register that selects complementary PWM mode, resetsynchronized PWM mode, and buffering for channels 3 and 4.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 CMD1 0 R/W 4 CMD0 0 R/W 3 BFB4 0 R/W 2 BFA4 0 R/W 1 BFB3 0 R/W 0 BFA3 0 R/W
Reserved bits Combination mode 1/0 These bits select complementary PWM mode or reset-synchronized PWM mode for channels 3 and 4 Buffer mode B4 and A4 These bits select buffering of general registers (GRB4 and GRA4) by buffer registers (BRB4 and BRA4) in channel 4 Buffer mode B3 and A3 These bits select buffering of general registers (GRB3 and GRA3) by buffer registers (BRB3 and BRA3) in channel 3
TFCR is initialized to H'C0 by a reset and in standby mode.
Rev.2.00 Mar. 22, 2007 Page 205 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bits 7 and 6--Reserved: These bits cannot be modified and are always read as 1. Bits 5 and 4--Combination Mode 1 and 0 (CMD1, CMD0): These bits select whether channels 3 and 4 operate in normal mode, complementary PWM mode, or reset-synchronized PWM mode.
Bit 5 CMD1 0 Bit 4 CMD0 0 1 1 0 1 Channels 3 and 4 operate together in complementary PWM mode Channels 3 and 4 operate together in reset-synchronized PWM mode Description Channels 3 and 4 operate normally (Initial value)
Before selecting reset-synchronized PWM mode or complementary PWM mode, halt the timer counter or counters that will be used in these modes. When these bits select complementary PWM mode or reset-synchronized PWM mode, they take precedence over the setting of the PWM mode bits (PWM4 and PWM3) in TMDR. Settings of timer sync bits SYNC4 and SYNC3 in the timer synchro register (TSNC) are valid in complementary PWM mode and reset-synchronized PWM mode, however. When complementary PWM mode is selected, channels 3 and 4 must not be synchronized (do not set bits SYNC3 and SYNC4 both to 1 in TSNC). Bit 3--Buffer Mode B4 (BFB4): Selects whether GRB4 operates normally in channel 4, or whether GRB4 is buffered by BRB4.
Bit 3 BFB4 0 1 Description GRB4 operates normally GRB4 is buffered by BRB4 (Initial value)
Bit 2--Buffer Mode A4 (BFA4): Selects whether GRA4 operates normally in channel 4, or whether GRA4 is buffered by BRA4.
Bit 2 BFA4 0 1 Description GRA4 operates normally GRA4 is buffered by BRA4 (Initial value)
Rev.2.00 Mar. 22, 2007 Page 206 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bit 1--Buffer Mode B3 (BFB3): Selects whether GRB3 operates normally in channel 3, or whether GRB3 is buffered by BRB3.
Bit 1 BFB3 0 1 Description GRB3 operates normally GRB3 is buffered by BRB3 (Initial value)
Bit 0--Buffer Mode A3 (BFA3): Selects whether GRA3 operates normally in channel 3, or whether GRA3 is buffered by BRA3.
Bit 0 BFA3 0 1 Description GRA3 operates normally GRA3 is buffered by BRA3 (Initial value)
8.2.5
Timer Output Master Enable Register (TOER)
TOER is an 8-bit readable/writable register that enables or disables output settings for channels 3 and 4.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 EXB4 1 R/W 4 EXA4 1 R/W 3 EB3 1 R/W 2 EB4 1 R/W 1 EA4 1 R/W 0 EA3 1 R/W
Reserved bits Master enable TOCXA4, TOCXB4 These bits enable or disable output settings for pins TOCXA4 and TOCXB4 Master enable TIOCA3, TIOCB3 , TIOCA4, TIOCB4 These bits enable or disable output settings for pins TIOCA3, TIOCB3 , TIOCA4, and TIOCB4
TOER is initialized to H'FF by a reset and in standby mode.
Rev.2.00 Mar. 22, 2007 Page 207 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bits 7 and 6--Reserved: These bits cannot be modified and are always read as 1. Bit 5--Master Enable TOCXB4 (EXB4): Enables or disables ITU output at pin TOCXB4.
Bit 5 EXB4 0 Description TOCXB4 output is disabled regardless of TFCR settings (TOCXB4 operates as a generic input/output pin). If XTGD = 0, EXB4 is cleared to 0 when input capture A occurs in channel 1. TOCXB4 is enabled for output according to TFCR settings (Initial value)
1
Bit 4--Master Enable TOCXA4 (EXA4): Enables or disables ITU output at pin TOCXA4.
Bit 4 EXA4 0 Description TOCXA4 output is disabled regardless of TFCR settings (TOCXA4 operates as a generic input/output pin). If XTGD = 0, EXA4 is cleared to 0 when input capture A occurs in channel 1. TOCXA4 is enabled for output according to TFCR settings (Initial value)
1
Bit 3--Master Enable TIOCB3 (EB3): Enables or disables ITU output at pin TIOCB3.
Bit 3 EB3 0 Description TIOCB3 output is disabled regardless of TIOR3 and TFCR settings (TIOCB3 operates as a generic input/output pin). If XTGD = 0, EB3 is cleared to 0 when input capture A occurs in channel 1. TIOCB3 is enabled for output according to TIOR3 and TFCR settings (Initial value)
1
Bit 2--Master Enable TIOCB4 (EB4): Enables or disables ITU output at pin TIOCB4.
Bit 2 EB4 0 Description TIOCB4 output is disabled regardless of TIOR4 and TFCR settings (TIOCB4 operates as a generic input/output pin). If XTGD = 0, EB4 is cleared to 0 when input capture A occurs in channel 1. TIOCB4 is enabled for output according to TIOR4 and TFCR settings (Initial value)
1
Rev.2.00 Mar. 22, 2007 Page 208 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bit 1--Master Enable TIOCA4 (EA4): Enables or disables ITU output at pin TIOCA4.
Bit 1 EA4 0 Description TIOCA4 output is disabled regardless of TIOR4, TMDR, and TFCR settings (TIOCA4 operates as a generic input/output pin). If XTGD = 0, EA4 is cleared to 0 when input capture A occurs in channel 1. TIOCA4 is enabled for output according to TIOR4, TMDR, and TFCR settings (Initial value)
1
Bit 0--Master Enable TIOCA3 (EA3): Enables or disables ITU output at pin TIOCA3.
Bit 0 EA3 0 Description TIOCA3 output is disabled regardless of TIOR3, TMDR, and TFCR settings (TIOCA3 operates as a generic input/output pin). If XTGD = 0, EA3 is cleared to 0 when input capture A occurs in channel 1. TIOCA3 is enabled for output according to TIOR3, TMDR, and TFCR settings (Initial value)
1
Rev.2.00 Mar. 22, 2007 Page 209 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.2.6
Timer Output Control Register (TOCR)
TOCR is an 8-bit readable/writable register that selects externally triggered disabling of output in complementary PWM mode and reset-synchronized PWM mode, and inverts the output levels.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- Reserved bits 5 -- 1 -- 4 XTGD 1 R/W 3 -- 1 -- 2 --1 -- 1 OLS4 1 R/W 0 OLS3 1 R/W
Output level select 3, 4 These bits select output levels in complementary PWM mode and resetsynchronized PWM mode Reserved bits
External trigger disable Selects externally triggered disabling of output in complementary PWM mode and reset-synchronized PWM mode
The settings of the XTGD, OLS4, and OLS3 bits are valid only in complementary PWM mode and reset-synchronized PWM mode. These settings do not affect other modes. TOCR is initialized to H'FF by a reset and in standby mode. Bits 7 to 5--Reserved: These bits cannot be modified and are always read as 1. Bit 4--External Trigger Disable (XTGD): Selects externally triggered disabling of ITU output in complementary PWM mode and reset-synchronized PWM mode.
Bit 4 XTGD 0 Description Input capture A in channel 1 is used as an external trigger signal in complementary PWM mode and reset-synchronized PWM mode. When an external trigger occurs, bits 5 to 0 in the timer output master enable register (TOER) are cleared to 0, disabling ITU output. External triggering is disabled (Initial value)
1
Rev.2.00 Mar. 22, 2007 Page 210 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bits 3 and 2--Reserved: These bits cannot be modified and are always read as 1. Bit 1--Output Level Select 4 (OLS4): Selects output levels in complementary PWM mode and reset-synchronized PWM mode.
Bit 1 OLS4 0 1 Description TIOCA3, TIOCA4, and TIOCB4 pin outputs are inverted TIOCA3, TIOCA4, and TIOCB4 pin outputs are not inverted (Initial value)
Bit 0--Output Level Select 3 (OLS3): Selects output levels in complementary PWM mode and reset-synchronized PWM mode.
Bit 0 OLS3 0 1 Description TIOCB3, TOCXA4, and TOCXB4 pin outputs are inverted TIOCB3, TOCXA4, and TOCXB4 pin outputs are not inverted (Initial value)
8.2.7
Timer Counters (TCNT)
TCNT is a 16-bit counter. The ITU has five TCNTs, one for each channel.
Chanel 0 1 2 3 4 Abbreviation TCNT0 TCNT1 TCNT2 TCNT3 TCNT4 Phase counting mode: up/down-counter Other modes: up-counter Complementary PWM mode: up/down-counter Other modes: up-counter Function Up-counter
Bit Initial value Read/Write
15 0
14 0
13 0
12 0
11 0
10 0
9 0
8 0
7 0
6 0
5 0
4 0
3 0
2 0
1 0
0 0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Each TCNT is a 16-bit readable/writable register that counts pulse inputs from a clock source. The clock source is selected by bits TPSC2 to TPSC0 in the timer control register (TCR).
Rev.2.00 Mar. 22, 2007 Page 211 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
TCNT0 and TCNT1 are up-counters. TCNT2 is an up/down-counter in phase counting mode and an up-counter in other modes. TCNT3 and TCNT4 are up/down-counters in complementary PWM mode and up-counters in other modes. TCNT can be cleared to H'0000 by compare match with general register A or B (GRA or GRB) or by input capture to GRA or GRB (counter clearing function) in the same channel. When TCNT overflows (changes from H'FFFF to H'0000), the overflow flag (OVF) is set to 1 in the timer status register (TSR) of the corresponding channel. When TCNT underflows (changes from H'0000 to H'FFFF), the overflow flag (OVF) is set to 1 in TSR of the corresponding channel. The TCNTs are linked to the CPU by an internal 16-bit bus and can be written or read by either word access or byte access. Each TCNT is initialized to H'0000 by a reset and in standby mode. 8.2.8 General Registers (GRA, GRB)
The general registers are 16-bit registers. The ITU has 10 general registers, two in each channel.
Channel 0 1 2 3 4 Abbreviation GRA0, GRB0 GRA1, GRB1 GRA2, GRB2 GRA3, GRB3 GRA4, GRB4 Output compare/input capture register; can be by buffer registers BRA and BRB Function Output compare/input capture register
Bit Initial value Read/Write
15 1
14 1
13 1
12 1
11 1
10 1
9 1
8 1
7 1
6 1
5 1
4 1
3 1
2 1
1 1
0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
A general register is a 16-bit readable/writable register that can function as either an output compare register or an input capture register. The function is selected by settings in the timer I/O control register (TIOR).
Rev.2.00 Mar. 22, 2007 Page 212 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
When a general register is used as an output compare register, its value is constantly compared with the TCNT value. When the two values match (compare match), the IMFA or IMFB flag is set to 1 in the timer status register (TSR). Compare match output can be selected in TIOR. When a general register is used as an input capture register, rising edges, falling edges, or both edges of an external input capture signal are detected and the current TCNT value is stored in the general register. The corresponding IMFA or IMFB flag in TSR is set to 1 at the same time. The valid edge or edges of the input capture signal are selected in TIOR. TIOR settings are ignored in PWM mode, complementary PWM mode, and reset-synchronized PWM mode. General registers are linked to the CPU by an internal 16-bit bus and can be written or read by either word access or byte access. General registers are initialized to the output compare function (with no output signal) by a reset and in standby mode. The initial value is H'FFFF. 8.2.9 Buffer Registers (BRA, BRB)
The buffer registers are 16-bit registers. The ITU has four buffer registers, two each in channels 3 and 4.
Channel 3 Abbreviation BRA3, BRB3 Function Used for buffering * When the corresponding GRA or GRB functions as an output compare register, BRA or BRB can function as an output compare buffer register: the BRA or BRB value is automatically transferred to GRA or GRB at compare match When the corresponding GRA or GRB functions as an input capture register, BRA or BRB can function as an input capture buffer register: the GRA or GRB value is automatically transferred to BRA or BRB at input capture
4
BRA4, BRB4
*
Bit Initial value Read/Write
15 1
14 1
13 1
12 1
11 1
10 1
9 1
8 1
7 1
6 1
5 1
4 1
3 1
2 1
1 1
0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Rev.2.00 Mar. 22, 2007 Page 213 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
A buffer register is a 16-bit readable/writable register that is used when buffering is selected. Buffering can be selected independently by bits BFB4, BFA4, BFB3, and BFA3 in TFCR. The buffer register and general register operate as a pair. When the general register functions as an output compare register, the buffer register functions as an output compare buffer register. When the general register functions as an input capture register, the buffer register functions as an input capture buffer register. The buffer registers are linked to the CPU by an internal 16-bit bus and can be written or read by either word or byte access. Buffer registers are initialized to H'FFFF by a reset and in standby mode. 8.2.10 Timer Control Registers (TCR)
TCR is an 8-bit register. The ITU has five TCRs, one in each channel.
Channel 0 1 2 3 4 Abbreviation TCR0 TCR1 TCR2 TCR3 TCR4 Function TCR controls the timer counter. The TCRs in all channels are functionally identical. When phase counting mode is selected in channel 2, the settings of bits CKEG1 and CKEG0 and TPSC2 to TPSC0 in TCR2 are ignored.
Bit Initial value Read/Write
7 -- 1 --
6 CCLR1 0 R/W
5 CCLR0 0 R/W
4 0 R/W
3 0 R/W
2 TPSC2 0 R/W
1 TPSC1 0 R/W
0 TPSC0 0 R/W
CKEG1 CKEG0
Timer prescaler 2 to 0 These bits select the counter clock Clock edge 1/0 These bits select external clock edges Counter clear 1/0 These bits select the counter clear source Reserved bit
Rev.2.00 Mar. 22, 2007 Page 214 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Each TCR is an 8-bit readable/writable register that selects the timer counter clock source, selects the edge or edges of external clock sources, and selects how the counter is cleared. TCR is initialized to H'80 by a reset and in standby mode. Bit 7--Reserved: This bit cannot be modified and is always read as 1. Bits 6 and 5--Counter Clear 1/0 (CCLR1, CCLR0): These bits select how TCNT is cleared.
Bit 6 CCLR1 0 Bit 5 CCLR0 0 1 1 0 1 Description TCNT is not cleared TCNT is cleared by GRA compare match or input capture* TCNT is cleared by GRB compare match or input capture* Synchronous clear: TCNT is cleared in synchronization 2 with other synchronized timers*
1 1
(Initial value)
Notes: 1. TCNT is cleared by compare match when the general register functions as an output compare match register, and by input capture when the general register functions as an input capture register. 2. Selected in the timer synchro register (TSNC).
Bits 4 and 3--Clock Edge 1/0 (CKEG1, CKEG0): These bits select external clock input edges when an external clock source is used.
Bit 4 CKEG1 0 Bit 3 CKEG0 0 1 1 -- Description Count rising edges Count falling edges Count both edges (Initial value)
When channel 2 is set to phase counting mode, bits CKEG1 and CKEG0 in TCR2 are ignored. Phase counting takes precedence.
Rev.2.00 Mar. 22, 2007 Page 215 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bits 2 to 0--Timer Prescaler 2 to 0 (TPSC2 to TPSC0): These bits select the counter clock source.
Bit 2 TPSC2 0 Bit 1 TPSC1 0 Bit 0 TPSC0 0 1 1 0 1 1 0 0 1 1 0 1 Function Internal clock: Internal clock: /2 Internal clock: /4 Internal clock: /8 External clock A: TCLKA input External clock B: TCLKB input External clock C: TCLKC input External clock D: TCLKD input (Initial value)
When bit TPSC2 is cleared to 0 an internal clock source is selected, and the timer counts only falling edges. When bit TPSC2 is set to 1 an external clock source is selected, and the timer counts the edge or edges selected by bits CKEG1 and CKEG0. When channel 2 is set to phase counting mode (MDF = 1 in TMDR), the settings of bits TPSC2 to TPSC0 in TCR2 are ignored. Phase counting takes precedence.
Rev.2.00 Mar. 22, 2007 Page 216 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.2.11
Timer I/O Control Register (TIOR)
TIOR is an 8-bit register. The ITU has five TIORs, one in each channel.
Channel 0 1 2 3 4 Abbreviation TIOR0 TIOR1 TIOR2 TIOR3 TIOR4 Function TIOR controls the general registers. Some functions differ in PWM mode. TIOR3 and TIOR4 settings are ignored when complementary PWM mode or reset-synchronized PWM mode is selected in channels 3 and 4.
Bit Initial value Read/Write
7 -- 1 --
6 IOB2 0 R/W
5 IOB1 0 R/W
4 IOB0 0 R/W
3 -- 1 --
2 IOA2 0 R/W
1 IOA1 0 R/W
0 IOA0 0 R/W
I/O control A2 to A0 These bits select GRA functions Reserved bit I/O control B2 to B0 These bits select GRB functions Reserved bit
Each TIOR is an 8-bit readable/writable register that selects the output compare or input capture function for GRA and GRB, and specifies the functions of the TIOCA and TIOCB pins. If the output compare function is selected, TIOR also selects the type of output. If input capture is selected, TIOR also selects the edge or edges of the input capture signal. TIOR is initialized to H'88 by a reset and in standby mode. Bit 7--Reserved: This bit cannot be modified and is always read as 1.
Rev.2.00 Mar. 22, 2007 Page 217 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bits 6 to 4--I/O Control B2 to B0 (IOB2 to IOB0): These bits select the GRB function.
Bit 6 IOB2 0 Bit 5 IOB1 0 Bit 4 IOB0 0 1 1 0 1 1 0 0 1 1 0 1 Notes: 1. After a reset, the output is 0 until the first compare match. 2. Channel 2 output cannot be toggled by compare match. This setting selects 1 output instead. GRB is an input capture register Function GRB is an output compare register No output at compare match (Initial value)
1 1
0 output at GRB compare match* 1 output at GRB compare match*
Output toggles at GRB compare match 1 2 (1 output in channel 2)* , * GRB captures rising edge of input GRB captures falling edge of input GRB captures both edges of input
Bit 3--Reserved: This bit cannot be modified and is always read as 1. Bits 2 to 0--I/O Control A2 to A0 (IOA2 to IOA0): These bits select the GRA function.
Bit 2 IOA2 0 Bit 1 IOA1 0 Bit 0 IOA0 0 1 1 0 1 1 0 0 1 1 0 1 Notes: 1. After a reset, the output is 0 until the first compare match. 2. Channel 2 output cannot be toggled by compare match. This setting selects 1 output instead. GRA is an input capture register Function GRA is an outpurt No output at compare match (Initial value) compare register 1 0 output at GRA compare match* 1 output at GRA compare match*
1
Output toggles at GRA compare match 1 2 (1 output in channel 2) * , * GRA captures rising edge of input GRA captures falling edge of input GRA captures both edges of input
Rev.2.00 Mar. 22, 2007 Page 218 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.2.12
Timer Status Register (TSR)
TSR is an 8-bit register. The ITU has five TSRs, one in each channel.
Channel 0 1 2 3 4 Abbreviation TSR0 TSR1 TSR2 TSR3 TSR4 Function Indicates input capture, compare match, and overflow status
Bit Initial value Read/Write
7 -- 1 --
6 -- 1 --
5 -- 1 -- Reserved bits
4 -- 1 --
3 -- 1 --
2 OVF 0 R/(W)*
1 IMFB 0 R/(W)*
0 IMFA 0 R/(W)*
Overflow flag Status flag indicating overflow or underflow Input capture/compare match flag B Status flag indicating GRB compare match or input capture Input capture/compare match flag A Status flag indicating GRA compare match or input capture Note: * Only 0 can be written to clear the flag.
Each TSR is an 8-bit readable/writable register containing flags that indicate TCNT overflow or underflow and GRA or GRB compare match or input capture. These flags are interrupt sources and generate CPU interrupts if enabled by corresponding bits in the timer interrupt enable register (TIER). TSR is initialized to H'F8 by a reset and in standby mode.
Rev.2.00 Mar. 22, 2007 Page 219 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bits 7 to 3--Reserved: These bits cannot be modified and are always read as 1. Bit 2--Overflow Flag (OVF): This status flag indicates TCNT overflow or underflow.
Bit 2 OVF 0 1 Notes: * Description [Clearing condition] Read OVF when OVF = 1, then write 0 in OVF (Initial value)
[Setting condition] TCNT overflowed from H'FFFF to H'0000, or underflowed from H'0000 to H'FFFF* TCNT underflow occurs when TCNT operates as an up/down-counter. Underflow occurs only under the following conditions: 1. Channel 2 operates in phase counting mode (MDF = 1 in TMDR) 2. Channels 3 and 4 operate in complementary PWM mode (CMD1 = 1 and CMD0 = 0 in TFCR)
Bit 1--Input Capture/Compare Match Flag B (IMFB): This status flag indicates GRB compare match or input capture events.
Bit 1 IMFB 0 1 Description [Clearing condition] Read IMFB when IMFB = 1, then write 0 in IMFB (Initial value)
[Setting conditions] TCNT = GRB when GRB functions as a compare match register. TCNT value is transferred to GRB by an input capture signal, when GRB functions as an input capture register.
Bit 0--Input Capture/Compare Match Flag A (IMFA): This status flag indicates GRA compare match or input capture events.
Bit 0 IMFA 0 1 Description [Clearing condition] Read IMFA when IMFA = 1, then write 0 in IMFA. (Initial value)
[Setting conditions] TCNT = GRA when GRA functions as a compare match register. TCNT value is transferred to GRA by an input capture signal, when GRA functions as an input capture register.
Rev.2.00 Mar. 22, 2007 Page 220 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.2.13
Timer Interrupt Enable Register (TIER)
TIER is an 8-bit register. The ITU has five TIERs, one in each channel.
Channel 0 1 2 3 4 Abbreviation TIER0 TIER1 TIER2 TIER3 TIER4 Function Enables or disables interrupt requests.
Bit Initial value Read/Write
7 -- 1 --
6 -- 1 --
5 -- 1 -- Reserved bits
4 -- 1 --
3 -- 1 --
2 OVIE 0 R/W
1 IMIEB 0 R/W
0 IMIEA 0 R/W
Overflow interrupt enable Enables or disables OVF interrupts Input capture/compare match interrupt enable B Enables or disables IMFB interrupts Input capture/compare match interrupt enable A Enables or disables IMFA interrupts
Each TIER is an 8-bit readable/writable register that enables and disables overflow interrupt requests and general register compare match and input capture interrupt requests. TIER is initialized to H'F8 by a reset and in standby mode.
Rev.2.00 Mar. 22, 2007 Page 221 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Bits 7 to 3--Reserved: These bits cannot be modified and are always read as 1. Bit 2--Overflow Interrupt Enable (OVIE): Enables or disables the interrupt requested by the overflow flag (OVF) in TSR when OVF is set to 1.
Bit 2 OVIE 0 1 Description OVI interrupt requested by OVF is disabled OVI interrupt requested by OVF is enabled (Initial value)
Bit 1--Input Capture/Compare Match Interrupt Enable B (IMIEB): Enables or disables the interrupt requested by the IMFB flag in TSR when IMFB is set to 1.
Bit 1 IMIEB 0 1 Description IMIB interrupt requested by IMFB is disabled IMIB interrupt requested by IMFB is enabled (Initial value)
Bit 0--Input Capture/Compare Match Interrupt Enable A (IMIEA): Enables or disables the interrupt requested by the IMFA flag in TSR when IMFA is set to 1.
Bit 0 IMIEA 0 1 Description IMIA interrupt requested by IMFA is disabled IMIA interrupt requested by IMFA is enabled (Initial value)
Rev.2.00 Mar. 22, 2007 Page 222 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.3
8.3.1
CPU Interface
16-Bit Accessible Registers
The timer counters (TCNTs), general registers A and B (GRAs and GRBs), and buffer registers A and B (BRAs and BRBs) are 16-bit registers, and are linked to the CPU by an internal 16-bit data bus. These registers can be written or read a word at a time, or a byte at a time. Figures 8.6 and 8.7 show examples of word access to a timer counter (TCNT). Figures 8.8, 8.9, 8.10, and 8.11 show examples of byte access to TCNTH and TCNTL.
Internal data bus H CPU L Bus interface H L Module data bus
TCNTH
TCNTL
Figure 8.6 Access to Timer Counter (CPU Writes to TCNT, Word)
Internal data bus H CPU L Bus interface H L Module data bus
TCNTH
TCNTL
Figure 8.7 Access to Timer Counter (CPU Reads TCNT, Word)
Rev.2.00 Mar. 22, 2007 Page 223 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Internal data bus H CPU L Bus interface H L Module data bus
TCNTH
TCNTL
Figure 8.8 Access to Timer Counter (CPU Writes to TCNT, Upper Byte)
Internal data bus H CPU L Bus interface H L Module data bus
TCNTH
TCNTL
Figure 8.9 Access to Timer Counter (CPU Writes to TCNT, Lower Byte)
Internal data bus H CPU L Bus interface H L Module data bus
TCNTH
TCNTL
Figure 8.10 Access to Timer Counter (CPU Reads TCNT, Upper Byte)
Rev.2.00 Mar. 22, 2007 Page 224 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Internal data bus H CPU L Bus interface H L Module data bus
TCNTH
TCNTL
Figure 8.11 Access to Timer Counter (CPU Reads TCNT, Lower Byte) 8.3.2 8-Bit Accessible Registers
The registers other than the timer counters, general registers, and buffer registers are 8-bit registers. These registers are linked to the CPU by an internal 8-bit data bus. Figures 8.12 and 8.13 show examples of byte read and write access to a TCR. If a word-size data transfer instruction is executed, two byte transfers are performed.
Internal data bus H CPU L Bus interface H L Module data bus
TCR
Figure 8.12 TCR Access (CPU Writes to TCR)
Internal data bus H CPU L Bus interface H L Module data bus
TCR
Figure 8.13 TCR Access (CPU Reads TCR)
Rev.2.00 Mar. 22, 2007 Page 225 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.4
8.4.1
Operation
Overview
A summary of operations in the various modes is given below. Normal Operation: Each channel has a timer counter and general registers. The timer counter counts up, and can operate as a free-running counter, periodic counter, or external event counter. General registers A and B can be used for input capture or output compare. Synchronous Operation: The timer counters in designated channels are preset synchronously. Data written to the timer counter in any one of these channels is simultaneously written to the timer counters in the other channels as well. The timer counters can also be cleared synchronously if so designated by the CCLR1 and CCLR0 bits in the TCRs. PWM Mode: A PWM waveform is output from the TIOCA pin. The output goes to 1 at compare match A and to 0 at compare match B. The duty cycle can be varied from 0% to 100% depending on the settings of GRA and GRB. When a channel is set to PWM mode, its GRA and GRB automatically become output compare registers. Reset-Synchronized PWM Mode: Channels 3 and 4 are paired for three-phase PWM output with complementary waveforms. (The three phases are related by having a common transition point.) When reset-synchronized PWM mode is selected GRA3, GRB3, GRA4, and GRB4 automatically function as output compare registers, TIOCA3, TIOCB3, TIOCA4, TOCXA4, TIOCB4, and TOCXB4 function as PWM output pins, and TCNT3 operates as an up-counter. TCNT4 operates independently, and is not compared with GRA4 or GRB4. Complementary PWM Mode: Channels 3 and 4 are paired for three-phase PWM output with non-overlapping complementary waveforms. When complementary PWM mode is selected GRA3, GRB3, GRA4, and GRB4 automatically function as output compare registers, and TIOCA3, TIOCB3, TIOCA4, TOCXA4, TIOCB4, and TOCXB4 function as PWM output pins. TCNT3 and TCNT4 operate as up/down-counters. Phase Counting Mode: The phase relationship between two clock signals input at TCLKA and TCLKB is detected and TCNT2 counts up or down accordingly. When phase counting mode is selected TCLKA and TCLKB become clock input pins and TCNT2 operates as an up/downcounter.
Rev.2.00 Mar. 22, 2007 Page 226 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Buffering * If the general register is an output compare register When compare match occurs the buffer register value is transferred to the general register. * If the general register is an input capture register When input capture occurs the TCNT value is transferred to the general register, and the previous general register value is transferred to the buffer register. * Complementary PWM mode The buffer register value is transferred to the general register when TCNT3 and TCNT4 change counting direction. * Reset-synchronized PWM mode The buffer register value is transferred to the general register at GRA3 compare match. 8.4.2 Basic Functions
Counter Operation: When one of bits STR0 to STR4 is set to 1 in the timer start register (TSTR), the timer counter (TCNT) in the corresponding channel starts counting. The counting can be freerunning or periodic. * Sample setup procedure for counter Figure 8.14 shows a sample procedure for setting up a counter.
Rev.2.00 Mar. 22, 2007 Page 227 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Counter setup
Select counter clock
1
Type of counting? Yes Periodic counting
No
Free-running counting
Select counter clear source
2
Select output compare register function
3
Set period
4
Start counter Periodic counter
5
Start counter Free-running counter
5
Figure 8.14 Counter Setup Procedure (Example) 1. Set bits TPSC2 to TPSC0 in TCR to select the counter clock source. If an external clock source is selected, set bits CKEG1 and CKEG0 in TCR to select the desired edge(s) of the external clock signal. 2. For periodic counting, set CCLR1 and CCLR0 in TCR to have TCNT cleared at GRA compare match or GRB compare match. 3. Set TIOR to select the output compare function of GRA or GRB, whichever was selected in step 2. 4. Write the count period in GRA or GRB, whichever was selected in step 2. 5. Set the STR bit to 1 in TSTR to start the timer counter.
Rev.2.00 Mar. 22, 2007 Page 228 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
* Free-running and periodic counter operation A reset leaves the counters (TCNTs) in ITU channels 0 to 4 all set as free-running counters. A free-running counter starts counting up when the corresponding bit in TSTR is set to 1. When the count overflows from H'FFFF to H'0000, the overflow flag (OVF) is set to 1 in the timer status register (TSR). If the corresponding OVIE bit is set to 1 in the timer interrupt enable register, a CPU interrupt is requested. After the overflow, the counter continues counting up from H'0000. Figure 8.15 illustrates free-running counting.
TCNT value H'FFFF
H'0000 STR0 to STR4 bit OVF
Time
Figure 8.15 Free-Running Counter Operation When a channel is set to have its counter cleared by compare match, in that channel TCNT operates as a periodic counter. Select the output compare function of GRA or GRB, set bit CCLR1 or CCLR0 in the timer control register (TCR) to have the counter cleared by compare match, and set the count period in GRA or GRB. After these settings, the counter starts counting up as a periodic counter when the corresponding bit is set to 1 in TSTR. When the count matches GRA or GRB, the IMFA or IMFB flag is set to 1 in TSR and the counter is cleared to H'0000. If the corresponding IMIEA or IMIEB bit is set to 1 in TIER, a CPU interrupt is requested at this time. After the compare match, TCNT continues counting up from H'0000. Figure 8.16 illustrates periodic counting.
Rev.2.00 Mar. 22, 2007 Page 229 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
TCNT value GR
Counter cleared by general register compare match
H'0000 STR bit IMF
Time
Figure 8.16 Periodic Counter Operation * Count timing Internal clock source Bits TPSC2 to TPSC0 in TCR select the system clock () or one of three internal clock sources obtained by prescaling the system clock (/2, 4, /8). Figure 8.17 shows the timing.
Internal clock TCNT input TCNT N1 N N+1
Figure 8.17 Count Timing for Internal Clock Sources
Rev.2.00 Mar. 22, 2007 Page 230 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
External clock source Bits TPSC2 to TPSC0 in TCR select an external clock input pin (TCLKA to TCLKD), and its valid edge or edges are selected by bits CKEG1 and CKEG0. The rising edge, falling edge, or both edges can be selected. The pulse width of the external clock signal must be at least 1.5 system clocks when a single edge is selected, and at least 2.5 system clocks when both edges are selected. Shorter pulses will not be counted correctly. Figure 8.18 shows the timing when both edges are detected.
External clock input TCNT input TCNT N-1 N N+1
Figure 8.18 Count Timing for External Clock Sources (when Both Edges are Detected)
Rev.2.00 Mar. 22, 2007 Page 231 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Waveform Output by Compare Match: In ITU channels 0, 1, 3, and 4, compare match A or B can cause the output at the TIOCA or TIOCB pin to go to 0, go to 1, or toggle. In channel 2 the output can only go to 0 or go to 1. * Sample setup procedure for waveform output by compare match Figure 8.19 shows a sample procedure for setting up waveform output by compare match.
Output setup 1. Select the compare match output mode (0, 1, or toggle) in TIOR. When a waveform output mode is selected, the pin switches from its generic input/ output function to the output compare function (TIOCA or TIOCB). An output compare pin outputs 0 until the first compare match occurs.
Select waveform output mode
1
Set output timing
2
2. Set a value in GRA or GRB to designate the compare match timing.
Start counter
3
3. Set the STR bit to 1 in TSTR to start the timer counter.
Waveform output
Figure 8.19 Setup Procedure for Waveform Output by Compare Match (Example) * Examples of waveform output Figure 8.20 shows examples of 0 and 1 output. TCNT operates as a free-running counter, 0 output is selected for compare match A, and 1 output is selected for compare match B. When the pin is already at the selected output level, the pin level does not change.
Rev.2.00 Mar. 22, 2007 Page 232 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
TCNT value H'FFFF GRB GRA H'0000 TIOCB Time No change No change 1 output
TIOCA
No change
No change
0 output
Figure 8.20 0 and 1 Output (Examples) Figure 8.21 shows examples of toggle output. TCNT operates as a periodic counter, cleared by compare match B. Toggle output is selected for both compare match A and B.
TCNT value GRB Counter cleared by compare match with GRB
GRA
H'0000 TIOCB
Time Toggle output Toggle output
TIOCA
Figure 8.21 Toggle Output (Example)
Rev.2.00 Mar. 22, 2007 Page 233 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
* Output compare timing The compare match signal is generated in the last state in which TCNT and the general register match (when TCNT changes from the matching value to the next value). When the compare match signal is generated, the output value selected in TIOR is output at the output compare pin (TIOCA or TIOCB). When TCNT matches a general register, the compare match signal is not generated until the next counter clock pulse. Figure 8.22 shows the output compare timing.
TCNT input clock TCNT N N+1
GR Compare match signal TIOCA, TIOCB
N
Figure 8.22 Output Compare Timing Input Capture Function: The TCNT value can be captured into a general register when a transition occurs at an input capture/output compare pin (TIOCA or TIOCB). Capture can take place on the rising edge, falling edge, or both edges. The input capture function can be used to measure pulse width or period. * Sample setup procedure for input capture Figure 8.23 shows a sample procedure for setting up input capture.
Rev.2.00 Mar. 22, 2007 Page 234 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Input selection
Select input-capture input
1
1. Set TIOR to select the input capture function of a general register and the rising edge, falling edge, or both edges of the input capture signal. Clear the port data direction bit to 0 before making these TIOR settings.
Start counter
2
2. Set the STR bit to 1 in TSTR to start the timer counter.
Input capture
Figure 8.23 Setup Procedure for Input Capture (Example) * Examples of input capture Figure 8.24 illustrates input capture when the falling edge of TIOCB and both edges of TIOCA are selected as capture edges. TCNT is cleared by input capture into GRB.
TCNT value H'0180 H'0160 H'0005 H'0000 TIOCB Counter cleared by TIOCB input (falling edge)
Time
TIOCA
GRA
H'0005
H'0160
GRB
H'0180
Figure 8.24 Input Capture (Example)
Rev.2.00 Mar. 22, 2007 Page 235 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
* Input capture signal timing Input capture on the rising edge, falling edge, or both edges can be selected by settings in TIOR. Figure 8.25 shows the timing when the rising edge is selected. The pulse width of the input capture signal must be at least 1.5 system clocks for single-edge capture, and 2.5 system clocks for capture of both edges.
Input-capture input
Internal input capture signal
TCNT
N
GRA, GRB
N
Figure 8.25 Input Capture Signal Timing
Rev.2.00 Mar. 22, 2007 Page 236 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.4.3
Synchronization
The synchronization function enables two or more timer counters to be synchronized by writing the same data to them simultaneously (synchronous preset). With appropriate TCR settings, two or more timer counters can also be cleared simultaneously (synchronous clear). Synchronization enables additional general registers to be associated with a single time base. Synchronization can be selected for all channels (0 to 4). Sample Setup Procedure for Synchronization: Figure 8.26 shows a sample procedure for setting up synchronization.
Setup for synchronization Select synchronization 1
Synchronous preset
Synchronous clear
Write to TCNT
2
Clearing synchronized to this channel? Yes Select counter clear source
No
3
Select counter clear source
4
Start counter
5
Start counter
5
Synchronous preset
Counter clear
Synchronous clear
1. Set the SYNC bits to 1 in TSNC for the channels to be synchronized. 2. When a value is written in TCNT in one of the synchronized channels, the same value is simultaneously written in TCNT in the other channels (synchronized preset). 3. Set the CCLR1 or CCLR0 bit in TCR to have the counter cleared by compare match or input capture. 4. Set the CCLR1 and CCLR0 bits in TCR to have the counter cleared synchronously. 5. Set the STR bits in TSTR to 1 to start the synchronized counters.
Figure 8.26 Setup Procedure for Synchronization (Example)
Rev.2.00 Mar. 22, 2007 Page 237 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Example of Synchronization: Figure 8.27 shows an example of synchronization. Channels 0, 1, and 2 are synchronized, and are set to operate in PWM mode. Channel 0 is set for counter clearing by compare match with GRB0. Channels 1 and 2 are set for synchronous counter clearing. The timer counters in channels 0, 1, and 2 are synchronously preset, and are synchronously cleared by compare match with GRB0. A three-phase PWM waveform is output from pins TIOCA0, TIOCA1, and TIOCA2. For further information on PWM mode, see section 8.4.4, PWM Mode.
Value of TCNT0 to TCNT2 Cleared by compare match with GRB0
GRB0 GRB1 GRA0 GRB2 GRA1 GRA2 H'0000 TIOCA0 Time
TIOCA1
TIOCA2
Figure 8.27 Synchronization (Example)
Rev.2.00 Mar. 22, 2007 Page 238 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.4.4
PWM Mode
In PWM mode GRA and GRB are paired and a PWM waveform is output from the TIOCA pin. GRA specifies the time at which the PWM output changes to 1. GRB specifies the time at which the PWM output changes to 0. If either GRA or GRB is selected as the counter clear source, a PWM waveform with a duty cycle from 0% to 100% is output at the TIOCA pin. PWM mode can be selected in all channels (0 to 4). Table 8.4 summarizes the PWM output pins and corresponding registers. If the same value is set in GRA and GRB, the output does not change when compare match occurs. Table 8.4
Channel 0 1 2 3 4
PWM Output Pins and Registers
Output Pin TIOCA0 TIOCA1 TIOCA2 TIOCA3 TIOCA4 1 Output GRA0 GRA1 GRA2 GRA3 GRA4 0 Output GRB0 GRB1 GRB2 GRB3 GRB4
Rev.2.00 Mar. 22, 2007 Page 239 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Sample Setup Procedure for PWM Mode: Figure 8.28 shows a sample procedure for setting up PWM mode.
PWM mode
Select counter clock
1
Select counter clear source
2
Set GRA
3
Set GRB
4
Select PWM mode
5
Start counter
6
PWM mode
1. Set bits TPSC2 to TPSC0 in TCR to select the counter clock source. If an external clock source is selected, set bits CKEG1 and CKEG0 in TCR to select the desired edge(s) of the external clock signal. 2. Set bits CCLR1 and CCLR0 in TCR to select the counter clear source. 3. Set the time at which the PWM waveform should go to 1 in GRA. 4. Set the time at which the PWM waveform should go to 0 in GRB. 5. Set the PWM bit in TMDR to select PWM mode. When PWM mode is selected, regardless of the TIOR contents, GRA and GRB become output compare registers specifying the times at which the PWM goes to 1 and 0. The TIOCA pin automatically becomes the PWM output pin. The TIOCB pin conforms to the settings of bits IOB1 and IOB0 in TIOR. If TIOCB output is not desired, clear both IOB1 and IOB0 to 0. 6. Set the STR bit to 1 in TSTR to start the timer counter.
Figure 8.28 Setup Procedure for PWM Mode (Example)
Rev.2.00 Mar. 22, 2007 Page 240 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Examples of PWM Mode: Figure 8.29 shows examples of operation in PWM mode. The PWM waveform is output from the TIOCA pin. The output goes to 1 at compare match with GRA, and to 0 at compare match with GRB. In the examples shown, TCNT is cleared by compare match with GRA or GRB. Synchronized operation and free-running counting are also possible.
TCNT value Counter cleared by compare match with GRA GRA
GRB
H'0000
Time
TIOCA a. Counter cleared by GRA
TCNT value Counter cleared by compare match with GRB GRB
GRA
H'0000
Time
TIOCA b. Counter cleared by GRB
Figure 8.29 PWM Mode (Example 1)
Rev.2.00 Mar. 22, 2007 Page 241 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Figure 8.30 shows examples of the output of PWM waveforms with duty cycles of 0% and 100%. If the counter is cleared by compare match with GRB, and GRA is set to a higher value than GRB, the duty cycle is 0%. If the counter is cleared by compare match with GRA, and GRB is set to a higher value than GRA, the duty cycle is 100%.
TCNT value GRB Counter cleared by compare match with GRB
GRA
H'0000
Time
TIOCA
Write to GRA a. 0% duty cycle TCNT value GRA
Write to GRA
Counter cleared by compare match with GRA
GRB
H'0000
Time
TIOCA
Write to GRB
Write to GRB
b. 100% duty cycle
Figure 8.30 PWM Mode (Example 2)
Rev.2.00 Mar. 22, 2007 Page 242 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.4.5
Reset-Synchronized PWM Mode
In reset-synchronized PWM mode channels 3 and 4 are combined to produce three pairs of complementary PWM waveforms, all having one waveform transition point in common. When reset-synchronized PWM mode is selected TIOCA3, TIOCB3, TIOCA4, TOCXA4, TIOCB4, and TOCXB4 automatically become PWM output pins, and TCNT3 functions as an up-counter. Table 8.5 lists the PWM output pins. Table 8.6 summarizes the register settings. Table 8.5
Channel 3
Output Pins in Reset-Synchronized PWM Mode
Output Pin TIOCA3 TIOCB3 TIOCA4 TOCXA4 TIOCB4 TOCXB4 Description PWM output 1 PWM output 1' (complementary waveform to PWM output 1) PWM output 2 PWM output 2' (complementary waveform to PWM output 2) PWM output 3 PWM output 3' (complementary waveform to PWM output 3)
4
Table 8.6
Register TCNT3 TCNT4 GRA3 GRB3 GRA4 GRB4
Register Settings in Reset-Synchronized PWM Mode
Setting Initially set to H'0000 Not used (operates independently) Specifies the count period of TCNT3 Specifies a transition point of PWM waveforms output from TIOCA3 and TIOCB3 Specifies a transition point of PWM waveforms output from TIOCA4 and TOCXA4 Specifies a transition point of PWM waveforms output from TIOCB4 and TOCXB4
Rev.2.00 Mar. 22, 2007 Page 243 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Sample Setup Procedure for Reset-Synchronized PWM Mode: Figure 8.31 shows a sample procedure for setting up reset-synchronized PWM mode.
Reset-synchronized PWM mode
Stop counter
1
Select counter clock
2
Select counter clear source
3
Select reset-synchronized PWM mode
4
Set TCNT
5
Set general registers
6
Start counter
7
Reset-synchronized PWM mode
1. Clear the STR3 bit in TSTR to 0 to halt TCNT3. Reset-synchronized PWM mode must be set up while TCNT3 is halted. 2. Set bits TPSC2 to TPSC0 in TCR to select the counter clock source for channel 3. If an external clock source is selected, select the external clock edge(s) with bits CKEG1 and CKEG0 in TCR. 3. Set bits CCLR1 and CCLR0 in TCR3 to select GRA3 compare match as the counter clear source. 4. Set bits CMD1 and CMD0 in TFCR to select reset-synchronized PWM mode. TIOCA3, TIOCB3, TIOCA4, TIOCB4, TOCXA4, and TOCXB4 automatically become PWM output pins. 5. Preset TCNT3 to H'0000. TCNT4 need not be preset. 6. GRA3 is the waveform period register. Set the waveform period value in GRA3. Set transition times of the PWM output waveforms in GRB3, GRA4, and GRB4. Set times within the compare match range of TCNT3. X GRA3 (X: setting value) 7. Set the STR3 bit in TSTR to 1 to start TCNT3.
Figure 8.31 Setup Procedure for Reset-Synchronized PWM Mode (Example)
Rev.2.00 Mar. 22, 2007 Page 244 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Example of Reset-Synchronized PWM Mode: Figure 8.32 shows an example of operation in reset-synchronized PWM mode. TCNT3 operates as an up-counter in this mode. TCNT4 operates independently, detached from GRA4 and GRB4. When TCNT3 matches GRA3, TCNT3 is cleared and resumes counting from H'0000. The PWM outputs toggle at compare match with GRB3, GRA4, GRB4, and TCNT3 respectively, and when the counter is cleared.
TCNT3 value Counter cleared at compare match with GRA3 GRA3 GRB3 GRA4 GRB4 H'0000 Time
TIOCA3
TIOCB3
TIOCA4
TOCXA4
TIOCB4
TOCXB4
Figure 8.32 Operation in Reset-Synchronized PWM Mode (Example) (when OLS3 = OLS4 = 1) For the settings and operation when reset-synchronized PWM mode and buffer mode are both selected, see section 8.4.8, Buffering.
Rev.2.00 Mar. 22, 2007 Page 245 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.4.6
Complementary PWM Mode
In complementary PWM mode channels 3 and 4 are combined to output three pairs of complementary, non-overlapping PWM waveforms. When complementary PWM mode is selected TIOCA3, TIOCB3, TIOCA4, TOCXA4, TIOCB4, and TOCXB4 automatically become PWM output pins, and TCNT3 and TCNT4 function as up/downcounters. Table 8.7 lists the PWM output pins. Table 8.8 summarizes the register settings. Table 8.7
Channel 3
Output Pins in Complementary PWM Mode
Output Pin TIOCA3 TIOCB3 Description PWM output 1 PWM output 1' (non-overlapping complementary waveform to PWM output 1) PWM output 2 PWM output 2' (non-overlapping complementary waveform to PWM output 2) PWM output 3 PWM output 3' (non-overlapping complementary waveform to PWM output 3)
4
TIOCA4 TOCXA4 TIOCB4 TOCXB4
Table 8.8
Register TCNT3 TCNT4 GRA3 GRB3 GRA4 GRB4
Register Settings in Complementary PWM Mode
Setting Initially specifies the non-overlap margin (difference to TCNT4) Initially set to H'0000 Specifies the upper limit value of TCNT3 minus 1 Specifies a transition point of PWM waveforms output from TIOCA3 and TIOCB3 Specifies a transition point of PWM waveforms output from TIOCA4 and TOCXA4 Specifies a transition point of PWM waveforms output from TIOCB4 and TOCXB4
Rev.2.00 Mar. 22, 2007 Page 246 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Setup Procedure for Complementary PWM Mode: Figure 8.33 shows a sample procedure for setting up complementary PWM mode.
Complementary PWM mode
Stop counting
1
1. Clear bits STR3 and STR4 to 0 in TSTR to halt the timer counters. Complementary PWM mode must be set up while TCNT3 and TCNT4 are halted. 2. Set bits TPSC2 to TPSC0 in TCR to select the same counter clock source for channels 3 and 4. If an external clock source is selected, select the external clock edge(s) with bits CKEG1 and CKEG0 in TCR. Do not select any counter clear source with bits CCLR1 and CCLR0 in TCR. 3. Set bits CMD1 and CMD0 in TFCR to select complementary PWM mode. TIOCA3, TIOCB3, TIOCA4, TIOCB4, TOCXA4, and TOCXB4 automatically become PWM output pins. 4. Clear TCNT4 to H'0000. Set the non-overlap margin in TCNT3. Do not set TCNT3 and TCNT4 to the same value. 5. GRA3 is the waveform period register. Set the upper limit value of TCNT3 minus 1 in GRA3. Set transition times of the PWM output waveforms in GRB3, GRA4, and GRB4. Set times within the compare match range of TCNT3 and TCNT4. T X (X: initial setting of GRB3, GRA4, or GRB4. T: initial setting of TCNT3) 6. Set bits STR3 and STR4 in TSTR to 1 to start TCNT3 and TCNT4.
Select counter clock
2
Select complementary PWM mode
3
Set TCNTs
4
Set general registers
5
Start counters
6
Complementary PWM mode
Note: After exiting complementary PWM mode, to resume operating in complementary PWM mode, follow the entire setup procedure from step 1 again.
Figure 8.33 Setup Procedure for Complementary PWM Mode (Example)
Rev.2.00 Mar. 22, 2007 Page 247 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Clearing Complementary PWM Mode: Figure 8.34 shows a sample procedure for clearing complementary PWM mode.
Complementary PWM mode 1. Clear bit CMD1 in TFCR to 0, and set channels 3 and 4 to normal operating mode. 2. After setting channels 3 and 4 to normal operating mode, wait at least one clock count before clearing bits STR3 and STR4 of TSTR to 0 to stop the counter operation of TCNT3 and TCNT4.
Clear complementary mode
1
Stop counting
2
Normal operation
Figure 8.34 Clearing Procedure for Complementary PWM Mode (Example)
Rev.2.00 Mar. 22, 2007 Page 248 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Examples of Complementary PWM Mode: Figure 8.35 shows an example of operation in complementary PWM mode. TCNT3 and TCNT4 operate as up/down-counters, counting down from compare match between TCNT3 and GRA3 and counting up from the point at which TCNT4 underflows. During each up-and-down counting cycle, PWM waveforms are generated by compare match with general registers GRB3, GRA4, and GRB4. Since TCNT3 is initially set to a higher value than TCNT4, compare match events occur in the sequence TCNT3, TCNT4, TCNT4, TCNT3.
TCNT3 and TCNT4 values GRA3 TCNT3 GRB3 GRA4 GRB4 H'0000 Up-counting starts when TCNT4 underflows TCNT4
Down-counting starts at compare match between TCNT3 and GRA3
Time
TIOCA3
TIOCB3
TIOCA4
TOCXA4
TIOCB4
TOCXB4
Figure 8.35 Operation in Complementary PWM Mode (Example 1) (when OLS3 = OLS4 = 1)
Rev.2.00 Mar. 22, 2007 Page 249 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Figure 8.36 shows examples of waveforms with 0% and 100% duty cycles (in one phase) in complementary PWM mode. In this example the outputs change at compare match with GRB3, so waveforms with duty cycles of 0% or 100% can be output by setting GRB3 to a value larger than GRA3. The duty cycle can be changed easily during operation by use of the buffer registers. For further information see section 8.4.8, Buffering.
TCNT3 and TCNT4 values GRA3
GRB3
H'0000 TIOCA3 TIOCB3 0% duty cycle a. 0% duty cycle TCNT3 and TCNT4 values GRA3
Time
GRB3
H'0000 TIOCA3 TIOCB3 100% duty cycle b. 100% duty cycle
Time
Figure 8.36 Operation in Complementary PWM Mode (Example 2) (when OLS3 = OLS4 = 1)
Rev.2.00 Mar. 22, 2007 Page 250 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
In complementary PWM mode, TCNT3 and TCNT4 overshoot and undershoot at the transitions between up-counting and down-counting. The setting conditions for the IMFA bit in channel 3 and the OVF bit in channel 4 differ from the usual conditions. In buffered operation the buffer transfer conditions also differ. Timing diagrams are shown in figures 8.37 and 8.38.
TCNT3 N-1 N N+1 N N-1
GRA3
N
IMFA Set to 1 Buffer transfer signal (BR to GR)
Flag not set
GR Buffer transfer No buffer transfer
Figure 8.37 Overshoot Timing
Rev.2.00 Mar. 22, 2007 Page 251 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Underflow TCNT4 H'0001 H'0000 H'FFFF Overflow H'0000
OVF Set to 1 Buffer transfer signal (BR to GR)
Flag not set
GR Buffer transfer No buffer transfer
Figure 8.38 Undershoot Timing In channel 3, IMFA is set to 1 only during up-counting. In channel 4, OVF is set to 1 only when an underflow occurs. When buffering is selected, buffer register contents are transferred to the general register at compare match A3 during up-counting, and when TCNT4 underflows. General Register Settings in Complementary PWM Mode: When setting up general registers for complementary PWM mode or changing their settings during operation, note the following points. * Initial settings Do not set values from H'0000 to T - 1 (where T is the initial value of TCNT3). After the counters start and the first compare match A3 event has occurred, however, settings in this range also become possible. * Changing settings Use the buffer registers. Correct waveform output may not be obtained if a general register is written to directly. * Cautions on changes of general register settings Figure 8.39 shows six correct examples and one incorrect example.
Rev.2.00 Mar. 22, 2007 Page 252 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
GRA3 GR
H'0000 BR
Not allowed
GR
Figure 8.39 Changing a General Register Setting by Buffer Transfer (Example 1) Buffer transfer at transition from up-counting to down-counting If the general register value is in the range from GRA3 - T + 1 to GRA3, do not transfer a buffer register value outside this range. Conversely, if the general register value is outside this range, do not transfer a value within this range. See figure 8.40.
GRA3 + 1 GRA3
Illegal changes
GRA3 - T + 1 GRA3 - T
TCNT3
TCNT4
Figure 8.40 Changing a General Register Setting by Buffer Transfer (Caution 1)
Rev.2.00 Mar. 22, 2007 Page 253 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Buffer transfer at transition from down-counting to up-counting If the general register value is in the range from H'0000 to T - 1, do not transfer a buffer register value outside this range. Conversely, when a general register value is outside this range, do not transfer a value within this range. See figure 8.41.
TCNT3 TCNT4 T T-1 Illegal changes H'0000 H'FFFF
Figure 8.41 Changing a General Register Setting by Buffer Transfer (Caution 2)
Rev.2.00 Mar. 22, 2007 Page 254 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
General register settings outside the counting range (H'0000 to GRA3) Waveforms with a duty cycle of 0% or 100% can be output by setting a general register to a value outside the counting range. When a buffer register is set to a value outside the counting range, then later restored to a value within the counting range, the counting direction (up or down) must be the same both times. See figure 8.42.
GRA3 GR H'0000 0% duty cycle Output pin Output pin 100% duty cycle
BR
GR Write during down-counting Write during up-counting
Figure 8.42 Changing a General Register Setting by Buffer Transfer (Example 2) Settings can be made in this way by detecting GRA3 compare match or TCNT4 underflow before writing to the buffer register.
Rev.2.00 Mar. 22, 2007 Page 255 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.4.7
Phase Counting Mode
In phase counting mode the phase difference between two external clock inputs (at the TCLKA and TCLKB pins) is detected, and TCNT2 counts up or down accordingly. In phase counting mode, the TCLKA and TCLKB pins automatically function as external clock input pins and TCNT2 becomes an up/down-counter, regardless of the settings of bits TPSC2 to TPSC0, CKEG1, and CKEG0 in TCR2. Settings of bits CCLR1, CCLR0 in TCR2, and settings in TIOR2, TIER2, TSR2, GRA2, and GRB2 are valid. The input capture and output compare functions can be used, and interrupts can be generated. Phase counting is available only in channel 2. Sample Setup Procedure for Phase Counting Mode: Figure 8.43 shows a sample procedure for setting up phase counting mode.
Phase counting mode
Select phase counting mode
1
Select flag setting condition
2
1. Set the MDF bit in TMDR to 1 to select phase counting mode. 2. Select the flag setting condition with the FDIR bit in TMDR. 3. Set the STR2 bit to 1 in TSTR to start the timer counter.
Start counter
3
Phase counting mode
Figure 8.43 Setup Procedure for Phase Counting Mode (Example)
Rev.2.00 Mar. 22, 2007 Page 256 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Example of Phase Counting Mode: Figure 8.44 shows an example of operations in phase counting mode. Table 8.9 lists the up-counting and down-counting conditions for TCNT2. In phase counting mode both the rising and falling edges of TCLKA and TCLKB are counted. The phase difference between TCLKA and TCLKB must be at least 1.5 states, the phase overlap must also be at least 1.5 states, and the pulse width must be at least 2.5 states. See figure 8.45.
TCNT2 value Counting up Counting down
Time TCLKB TCLKA
Figure 8.44 Operation in Phase Counting Mode (Example) Table 8.9 Up/Down Counting Conditions
Up-Counting High Low High Low Down-Counting High Low Low High
Counting Direction TCLKB TCLKA
Phase difference
Phase difference
Pulse width
Pulse width
TCLKA
TCLKB Phase difference and overlap: at least 1.5 states Pulse width: at least 2.5 states
Overlap
Overlap
Figure 8.45 Phase Difference, Overlap, and Pulse Width in Phase Counting Mode
Rev.2.00 Mar. 22, 2007 Page 257 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.4.8
Buffering
Buffering operates differently depending on whether a general register is an output compare register or an input capture register, with further differences in reset-synchronized PWM mode and complementary PWM mode. Buffering is available only in channels 3 and 4. Buffering operations under the conditions mentioned above are described next. * General register used for output compare The buffer register value is transferred to the general register at compare match. See figure 8.46.
Compare match signal
BR
GR
Comparator
TCNT
Figure 8.46 Compare Match Buffering * General register used for input capture The TCNT value is transferred to the general register at input capture. The previous general register value is transferred to the buffer register. See figure 8.47.
Input capture signal
BR
GR
TCNT
Figure 8.47 Input Capture Buffering
Rev.2.00 Mar. 22, 2007 Page 258 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
* Complementary PWM mode The buffer register value is transferred to the general register when TCNT3 and TCNT4 change counting direction. This occurs at the following two times: When TCNT3 matches GRA3 When TCNT4 underflows * Reset-synchronized PWM mode The buffer register value is transferred to the general register at compare match A3. Sample Buffering Setup Procedure: Figure 8.48 shows a sample buffering setup procedure.
Buffering
Select general register functions
1
Set buffer bits
2
1. Set TIOR to select the output compare or input capture function of the general registers. 2. Set bits BFA3, BFA4, BFB3, and BFB4 in TFCR to select buffering of the required general registers. 3. Set the STR bits to 1 in TSTR to start the timer counters.
Start counters
3
Buffered operation
Figure 8.48 Buffering Setup Procedure (Example)
Rev.2.00 Mar. 22, 2007 Page 259 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Examples of Buffering: Figure 8.49 shows an example in which GRA is set to function as an output compare register buffered by BRA, TCNT is set to operate as a periodic counter cleared by GRB compare match, and TIOCA and TIOCB are set to toggle at compare match A and B. Because of the buffer setting, when TIOCA toggles at compare match A, the BRA value is simultaneously transferred to GRA. This operation is repeated each time compare match A occurs. Figure 8.50 shows the transfer timing.
TCNT value GRB H'0250 H'0200 H'0100 H'0000 BRA GRA TIOCB TIOCA H'0200 H'0250 H'0100 H'0200 H'0100 H'0200 H'0200 Toggle output Toggle output Time Counter cleared by compare match B
Compare match A
Figure 8.49 Register Buffering (Example 1: Buffering of Output Compare Register)
Rev.2.00 Mar. 22, 2007 Page 260 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
TCNT Compare match signal Buffer transfer signal BR GR n N N n n+1
Figure 8.50 Compare Match and Buffer Transfer Timing (Example)
Rev.2.00 Mar. 22, 2007 Page 261 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Figure 8.51 shows an example in which GRA is set to function as an input capture register buffered by BRA, and TCNT is cleared by input capture B. The falling edge is selected as the input capture edge at TIOCB. Both edges are selected as input capture edges at TIOCA. Because of the buffer setting, when the TCNT value is captured into GRA at input capture A, the previous GRA value is simultaneously transferred to BRA. Figure 8.52 shows the transfer timing.
TCNT value H'0180 H'0160 Counter cleared by input capture B
H'0005 H'0000 TIOCB
Time
TIOCA
GRA
H'0005
H'0160
BRA
H'0005
H'0160
GRB
H'0180
Input capture A
Figure 8.51 Register Buffering (Example 2: Buffering of Input Capture Register)
Rev.2.00 Mar. 22, 2007 Page 262 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
TIOC pin Input capture signal TCNT GR BR M m n n M n+1 N n M N n N+1
Figure 8.52 Input Capture and Buffer Transfer Timing (Example)
Rev.2.00 Mar. 22, 2007 Page 263 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Figure 8.53 shows an example in which GRB3 is buffered by BRB3 in complementary PWM mode. Buffering is used to set GRB3 to a higher value than GRA3, generating a PWM waveform with 0% duty cycle. The BRB3 value is transferred to GRB3 when TCNT3 matches GRA3, and when TCNT4 underflows.
TCNT3 and TCNT4 values H'1FFF GRA3 TCNT3 TCNT4 GRB3
H'0999
H'0000
Time
BRB3 GRB3
H'0999 H'0999 H'0999
H'1FFF H'1FFF H'1FFF
H'0999 H'0999
TIOCA3
TIOCB3
Figure 8.53 Register Buffering (Example 4: Buffering in Complementary PWM Mode)
Rev.2.00 Mar. 22, 2007 Page 264 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.4.9
ITU Output Timing
The ITU outputs from channels 3 and 4 can be disabled by bit settings in TOER or by an external trigger, or inverted by bit settings in TOCR. Timing of Enabling and Disabling of ITU Output by TOER: In this example an ITU output is disabled by clearing a master enable bit to 0 in TOER. An arbitrary value can be output by appropriate settings of the data register (DR) and data direction register (DDR) of the corresponding input/output port. Figure 8.54 illustrates the timing of the enabling and disabling of ITU output by TOER.
T1 T2 T3
Address
TOER address
TOER
ITU output pin
Timer output
I/O port
ITU output
Generic input/output
Figure 8.54 Timing of Disabling of ITU Output by Writing to TOER (Example)
Rev.2.00 Mar. 22, 2007 Page 265 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Timing of Disabling of ITU Output by External Trigger: If the XTGD bit is cleared to 0 in TOCR in reset-synchronized PWM mode or complementary PWM mode, when an input capture A signal occurs in channel 1, the master enable bits are cleared to 0 in TOER, disabling ITU output. Figure 8.55 shows the timing.
TIOCA1 pin Input capture signal TOER ITU output pins N ITU output ITU output N: Arbitrary setting (H'C1 to H'FF) H'C0 I/O port Generic input/output N ITU output ITU output H'C0 I/O port Generic input/output
Figure 8.55 Timing of Disabling of ITU Output by External Trigger (Example) Timing of Output Inversion by TOCR: The output levels in reset-synchronized PWM mode and complementary PWM mode can be inverted by inverting the output level select bits (OLS4 and OLS3) in TOCR. Figure 8.56 shows the timing.
T1 T2 T3
Address
TOCR address
TOCR
ITU output pin Inverted
Figure 8.56 Timing of Inverting of ITU Output Level by Writing to TOCR (Example)
Rev.2.00 Mar. 22, 2007 Page 266 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.5
Interrupts
The ITU has two types of interrupts: input capture/compare match interrupts, and overflow interrupts. 8.5.1 Setting of Status Flags
Timing of Setting of IMFA and IMFB at Compare Match: IMFA and IMFB are set to 1 by a compare match signal generated when TCNT matches a general register (GR). The compare match signal is generated in the last state in which the values match (when TCNT is updated from the matching count to the next count). Therefore, when TCNT matches a general register, the compare match signal is not generated until the next timer clock input. Figure 8.57 shows the timing of the setting of IMFA and IMFB.
TCNT input clock
TCNT
N
N+1
GR
N
Compare match signal
IMF
IMI
Figure 8.57 Timing of Setting of IMFA and IMFB by Compare Match
Rev.2.00 Mar. 22, 2007 Page 267 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Timing of Setting of IMFA and IMFB by Input Capture: IMFA and IMFB are set to 1 by an input capture signal. The TCNT contents are simultaneously transferred to the corresponding general register. Figure 8.58 shows the timing.
Input capture signal
IMF
TCNT
N
GR
N
IMI
Figure 8.58 Timing of Setting of IMFA and IMFB by Input Capture Timing of Setting of Overflow Flag (OVF): OVF is set to 1 when TCNT overflows from H'FFFF to H'0000 or underflows from H'0000 to H'FFFF. Figure 8.59 shows the timing.
Rev.2.00 Mar. 22, 2007 Page 268 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
TCNT
H'FFFF
H'0000
Overflow signal
OVF
OVI
Figure 8.59 Timing of Setting of OVF 8.5.2 Clearing of Status Flags
If the CPU reads a status flag while it is set to 1, then writes 0 in the status flag, the status flag is cleared. Figure 8.60 shows the timing.
TSR write cycle T1 T2 T3
Address
TSR address
IMF, OVF
Figure 8.60 Timing of Clearing of Status Flags
Rev.2.00 Mar. 22, 2007 Page 269 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.5.3
Interrupt Sources
Each ITU channel can generate a compare match/input capture A interrupt, a compare match/input capture B interrupt, and an overflow interrupt. In total there are 15 interrupt sources, all independently vectored. An interrupt is requested when the interrupt request flag and interrupt enable bit are both set to 1. The priority order of the channels can be modified in interrupt priority registers A and B (IPRA and IPRB). For details see section 5, Interrupt Controller. Table 8.10 lists the interrupt sources. Table 8.10 ITU Interrupt Sources
Channel 0 Interrupt Source IMIA0 IMIB0 OVI0 1 IMIA1 IMIB1 OVI1 2 IMIA2 IMIB2 OVI2 3 IMIA3 IMIB3 OVI3 4 IMIA4 IMIB4 OVI4 Description Compare match/input capture A0 Compare match/input capture B0 Overflow 0 Compare match/input capture A1 Compare match/input capture B1 Overflow 1 Compare match/input capture A2 Compare match/input capture B2 Overflow 2 Compare match/input capture A3 Compare match/input capture B3 Overflow 3 Compare match/input capture A4 Compare match/input capture B4 Overflow 4 Low Priority* High
Note: * The priority immediately after a reset is indicated. Inter-channel priorities can be changed by settings in IPRA and IPRB.
Rev.2.00 Mar. 22, 2007 Page 270 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
8.6
Usage Notes
This section describes contention and other matters requiring special attention during ITU operations. Contention between TCNT Write and Clear: If a counter clear signal occurs in the T3 state of a TCNT write cycle, clearing of the counter takes priority and the write is not performed. See figure 8.61.
TCNT write cycle T1 T2 T3
Address
TCNT address
Internal write signal
Counter clear signal
TCNT
N
H'0000
Figure 8.61 Contention between TCNT Write and Clear
Rev.2.00 Mar. 22, 2007 Page 271 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Contention between TCNT Word Write and Increment: If an increment pulse occurs in the T3 state of a TCNT word write cycle, writing takes priority and TCNT is not incremented. See figure 8.62.
TCNT word write cycle T1 T2 T3
Address
TCNT address
Internal write signal
TCNT input clock
TCNT
N
M TCNT write data
Figure 8.62 Contention between TCNT Word Write and Increment
Rev.2.00 Mar. 22, 2007 Page 272 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Contention between TCNT Byte Write and Increment: If an increment pulse occurs in the T2 or T3 state of a TCNT byte write cycle, writing takes priority and TCNT is not incremented. The TCNT byte that was not written retains its previous value. See figure 8.63, which shows an increment pulse occurring in the T2 state of a byte write to TCNTH.
TCNT byte write cycle T1 T2 T3
Address
TCNTH address
Internal write signal
TCNT input clock
TCNTH
N TCNT write data
M
TCNTL
X
X+1
X
Figure 8.63 Contention between TCNT Byte Write and Increment
Rev.2.00 Mar. 22, 2007 Page 273 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Contention between General Register Write and Compare Match: If a compare match occurs in the T3 state of a general register write cycle, writing takes priority and the compare match signal is inhibited. See figure 8.64.
General register write cycle T1 T2 T3
Address
GR address
Internal write signal
TCNT
N
N+1
GR
N
M General register write data
Compare match signal
Inhibited
Figure 8.64 Contention between General Register Write and Compare Match
Rev.2.00 Mar. 22, 2007 Page 274 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Contention between TCNT Write and Overflow or Underflow: If an overflow occurs in the T3 state of a TCNT write cycle, writing takes priority and the counter is not incremented. OVF is set to 1.The same holds for underflow. See figure 8.65.
TCNT write cycle T1 T2 T3
Address
TCNT address
Internal write signal
TCNT input clock
Overflow signal
TCNT
H'FFFF TCNT write data
M
OVF
Figure 8.65 Contention between TCNT Write and Overflow
Rev.2.00 Mar. 22, 2007 Page 275 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Contention between General Register Read and Input Capture: If an input capture signal occurs during the T3 state of a general register read cycle, the value before input capture is read. See figure 8.66.
General register read cycle T1 T2 T3
Address
GR address
Internal read signal
Input capture signal
GR
X
M
Internal data bus
X
Figure 8.66 Contention between General Register Read and Input Capture
Rev.2.00 Mar. 22, 2007 Page 276 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Contention between Counter Clearing by Input Capture and Counter Increment: If an input capture signal and counter increment signal occur simultaneously, the counter is cleared according to the input capture signal. The counter is not incremented by the increment signal. The value before the counter is cleared is transferred to the general register. See figure 8.67.
Input capture signal
Counter clear signal
TCNT input clock
TCNT
N
H'0000
GR
N
Figure 8.67 Contention between Counter Clearing by Input Capture and Counter Increment
Rev.2.00 Mar. 22, 2007 Page 277 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Contention between General Register Write and Input Capture: If an input capture signal occurs in the T3 state of a general register write cycle, input capture takes priority and the write to the general register is not performed. See figure 8.68.
General register write cycle T1 T2 T3
Address
GR address
Internal write signal
Input capture signal
TCNT
M
GR
M
Figure 8.68 Contention between General Register Write and Input Capture Note on Waveform Period Setting: When a counter is cleared by compare match, the counter is cleared in the last state at which the TCNT value matches the general register value, at the time when this value would normally be updated to the next count. The actual counter frequency is therefore given by the following formula: f=
(N + 1) (f: counter frequency. : system clock frequency. N: value set in general register.)
Rev.2.00 Mar. 22, 2007 Page 278 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Contention between Buffer Register Write and Input Capture: If a buffer register is used for input capture buffering and an input capture signal occurs in the T3 state of a write cycle, input capture takes priority and the write to the buffer register is not performed. See figure 8.69.
Buffer register write cycle T1 T2 T3
Address
BR address
Internal write signal
Input capture signal
GR
N
X TCNT value
BR
M
N
Figure 8.69 Contention between Buffer Register Write and Input Capture
Rev.2.00 Mar. 22, 2007 Page 279 of 684 REJ09B0352-0200
8. 16-Bit Integrated Timer Unit (ITU)
Note on Synchronous Preset: When channels are synchronized, if a TCNT value is modified by byte write access, all 16 bits of all synchronized counters assume the same value as the counter that was addressed. (Example) When channels 2 and 3 are synchronized
* Byte write to channel 2 or byte write to channel 3 Write A to upper byte of channel 2
TCNT2 TCNT3
W Y
X Z
TCNT2 TCNT3
A A
X X
Upper byte Lower byte
Write A to lower byte of channel 3 TCNT2 TCNT3
Upper byte Lower byte Y Y A A
Upper byte Lower byte * Word write to channel 2 or word write to channel 3 TCNT2 TCNT3 W Y X Z Write AB word to channel 2 or 3 TCNT2 TCNT3 A A B B
Upper byte Lower byte
Upper byte Lower byte
Note on Setup of Reset-Synchronized PWM Mode and Complementary PWM Mode: When setting bits CMD1 and CMD0 in TFCR, take the following precautions: * Write to bits CMD1 and CMD0 only when TCNT3 and TCNT4 are stopped. * Do not switch directly between reset-synchronized PWM mode and complementary PWM mode. First switch to normal mode (by clearing bit CMD1 to 0), then select reset-synchronized PWM mode or complementary PWM mode.
Rev.2.00 Mar. 22, 2007 Page 280 of 684 REJ09B0352-0200
ITU Operating Modes
Table 8.11 (a) ITU Operating Modes (Channel 0)
Register Settings TMDR TFCR TOCR TOER TIOR0 TCR0
TSNC
Operating Mode
Synchronization MDF FDIR PWM IOA
ResetComple- SynchroOutput mentary nized BufferLevel PWM PWM ing XTGD Select Master Enable IOB *
Clear Select
Clock Select
Synchronous preset PWM0 = 1 PWM0 = 0
SYNC0 = 1
PWM mode
--
IOA2 = 0 Other bits unrestricted
Output compare A
-- -- -- -- -- -- -- -- --
-- -- --
-- -- --
-- -- --
-- -- --
-- -- --
Output compare B
-- --
--
--
--
--
--
--
IOB2 = 0 Other bits unrestricted
Input capture A
--
PWM0 = 0
-- --
--
--
--
--
--
IOA2 = 1 Other bits unrestricted
Input capture B
--
PWM0 = 0
-- -- -- -- -- -- -- -- -- --
--
--
-- -- --
-- -- --
-- -- --
IOB2 = 1 Other bits unrestricted CCLR1 = 0 CCLR0 = 1 CCLR1 = 1 CCLR0 = 0
Counter By compare clearing match/input capture A
-- --
By compare match/input capture B
Synchronous clear
SYNC0 = 1
--
--
--
--
--
--
--
--
CCLR1 = 1 CCLR0 = 1
Legend:
Setting available (valid).
-- Setting does not afect this mode. f
8. 16-Bit Integrated Timer Unit (ITU)
Rev.2.00 Mar. 22, 2007 Page 281 of 684 REJ09B0352-0200
Note:
The input capture function cannot be used in PWM mode. If compare match A and compare match B occur simultaneously, the compare match signal is inhibited.
Table 8.11 (b) ITU Operating Modes (Channel 1)
Register Settings TMDR TFCR TOCR TOER TIOR1 TCR1
TSNC
Operating Mode
Synchronization MDF FDIR PWM IOA IOB
ResetComple- SynchroOutput mentary nized BufferLevel PWM PWM ing XTGD Select Master Enable
*1
Clear Select
Clock Select
Synchronous preset PWM1 = 1 PWM1 = 0
SYNC1 = 1
PWM mode
--
IOA2 = 0 Other bits unrestricted
8. 16-Bit Integrated Timer Unit (ITU)
Rev.2.00 Mar. 22, 2007 Page 282 of 684 REJ09B0352-0200
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
*2
Output compare A
Output compare B
-- --
--
IOB2 = 0 Other bits unrestricted
Input capture A
-- --
PWM1 = 0
-- --
--
--
--
IOA2 = 1 Other bits unrestricted
Input capture B
-- --
PWM1 = 0
-- -- -- -- -- -- --
--
--
-- -- --
-- -- --
-- -- --
IOB2 = 1 Other bits unrestricted CCLR1 = 0 CCLR0 = 1 CCLR1 = 1 CCLR0 = 0
Counter By compare clearing match/input capture A
-- -- -- --
By compare match/input capture B
Synchronous clear
SYNC1 = 1
-- -- --
--
--
--
--
--
CCLR1 = 1 CCLR0 = 1
Legend: Setting available (valid). -- Setting does not affect this mode. Notes: 1. The input capture function cannot be used in PWM mode. If compare match A and compare match B occur simultaneously, the compare match signal is inhibited. 2. Valid only when channels 3 and 4 are operating in complementary PWM mode or reset-synchronized PWM mode.
Table 8.11 (c) ITU Operating Modes (Channel 2)
Register Settings TMDR TFCR TOCR TOER TIOR2 TCR2
TSNC
Operating Mode -- -- -- PWM2 = 0 -- -- -- -- -- -- PWM2 = 1 -- -- -- -- -- -- -- IOA2 = 0 Other bits unrestricted -- -- -- -- -- --
Synchronization MDF FDIR PWM IOA IOB
ResetComple- SynchroOutput mentary nized BufferLevel PWM PWM ing XTGD Select Master Enable
Clear Select
Clock Select
Synchronous preset
SYNC2 = 1
PWM mode
*
Output compare A
Output compare B
--
--
--
--
--
--
--
IOB2 = 0 Other bits unrestricted -- IOA2 = 1 Other bits unrestricted
Input capture A
--
PWM2 = 0 --
--
--
--
--
Input capture B
--
PWM2 = 0 --
--
--
--
--
--
IOB2 = 1 Other bits unrestricted -- -- -- CCLR1 = 0 CCLR0 = 1
Counter By compare clearing match/input capture A -- -- --
--
--
--
--
By compare match/input capture B -- -- --
--
--
--
--
CCLR1 = 1 CCLR0 = 0 -- -- -- -- CCLR1 = 1 CCLR0 = 1
Synchronous clear MDF = 1 --
SYNC2 = 1
Phase counting mode
--
--
--
--
--
--
8. 16-Bit Integrated Timer Unit (ITU)
Rev.2.00 Mar. 22, 2007 Page 283 of 684 REJ09B0352-0200
Legend: Setting available (valid). -- Setting does not affect this mode. Note: The input capture function cannot be used in PWM mode. If compare match A and compare match B occur simultaneously, the compare match signal is inhibited.
Table 8.11 (d) ITU Operating Modes (Channel 3)
TMDR Complementary PWM IOA -- IOA2 = 0 Other bits unrestricted
*2
TSNC
TIOR3
TCR3
Operating Mode Synchronous preset PWM mode Output compare A
Synchronization MDF SYNC3 = 1 -- -- -- FDIR PWM *3 -- -- PWM3 = 1 CMD1 = 0 -- PWM3 = 0 CMD1 = 0 IOB
Register Settings TFCR TOCR TOER ResetOutput SynchroLevel Master nized PWM Buffering XTGD Select Enable *1 -- -- CMD1 = 0 -- -- CMD1 = 0 -- -- Clear Select
Clock Select
Output compare B
--
--
CMD1 = 0
CMD1 = 0
--
--
IOB2 = 0 Other bits unrestricted
8. 16-Bit Integrated Timer Unit (ITU)
Rev.2.00 Mar. 22, 2007 Page 284 of 684 REJ09B0352-0200
-- -- PWM3 = 0 CMD1 = 0 CMD1 = 0 -- -- -- -- PWM3 = 0 CMD1 = 0 CMD1 = 0 -- -- EA3 ignored IOA2 = 1 Other bits Other bits unrestricted unrestricted EB3 ignored IOB2 = 1 Other bits Other bits unrestricted unrestricted
*1
Input capture A
Input capture B
Counter clearing -- -- -- --
--
--
--
--
CCLR1 = 0 CCLR0 = 1
*1
*4 Illegal setting: CMD1 = 1 CMD0 = 0 CMD1 = 0 CMD1 = 0
CCLR1 = 1 CCLR0 = 0 -- --
*1
SYNC3 = 1 --
--
CCLR1 = 1 CCLR0 = 1
*6
*3
-- -- -- -- -- --
--
--
--
*6
-- -- --
*1
*5
By compare match/input capture A By compare match/input capture B Synchronous clear Complementary PWM mode Reset-synchronized PWM mode Buffering (BRA) Illegal setting: CMD1 = 1 CMD0 = 0 CMD1 = 1 CMD0 = 0 CMD1 = 1 CMD0 = 1 CMD1 = 1 CMD0 = 0 CMD1 = 1 CMD0 = 1 -- -- BFA3 = 1 -- Other bits unrestricted BFB3 = 1 -- Other bits unrestricted --
--
CCLR1 = 0 CCLR0 = 0 CCLR1 = 0 CCLR0 = 1
Buffering (BRB)
*1
Legend: Notes: 1. 2. 3. 4. 5. 6.
Setting available (valid). -- Setting does not afect this mode. f Master enable bit settings are valid only during waveform output. The input capture function cannot be used in PWM mode. If compare match A and compare match B occur simultaneously, the compare match signal is inhibited. Do not set both channels 3 and 4 for synchronous operation when complementary PWM mode is selected. The counter cannot be cleared by input capture A when reset-synchronized PWM mode is selected. In complementary PWM mode, select the same clock source for channels 3 and 4. Use the input capture A function in channel 1.
Table 8.11 (e) ITU Operating Modes (Channel 4)
TMDR Complementary PWM IOA -- IOA2 = 0 Other bits unrestricted
*2
TSNC
TIOR4
TCR4
Operating Mode Synchronous preset PWM mode Output compare A
Synchronization MDF SYNC4 = 1 -- -- -- FDIR PWM *3 -- -- PWM4 = 1 CMD1 = 0 -- PWM4 = 0 CMD1 = 0 IOB
Register Settings TFCR TOCR TOER ResetOutput SynchroLevel Master nized PWM Buffering XTGD Select Enable *1 -- -- CMD1 = 0 -- -- CMD1 = 0 -- -- Clear Select
Clock Select
Output compare B
--
--
CMD1 = 0
CMD1 = 0
--
--
IOB2 = 0 Other bits unrestricted
Input capture A
--
--
PWM4 = 0 CMD1 = 0
CMD1 = 0
--
--
Input capture B
--
--
PWM4 = 0 CMD1 = 0
CMD1 = 0
--
--
EA4 ignored IOA2 = 1 Other bits Other bits unrestricted unrestricted EB4 ignored IOB2 = 1 Other bits Other bits unrestricted unrestricted
*1
Counter clearing
*4
--
--
--
--
CCLR1 = 0 CCLR0 = 1 --
*1
--
*4
--
--
CCLR1 = 1 CCLR0 = 0 -- --
*1
SYNC4 = 1 --
*4
--
CCLR1 = 1 CCLR0 = 1 -- -- --
*1
*3
-- -- -- -- -- --
--
--
-- --
CCLR1 = 0 CCLR0 = 0
*6
*5
By compare match/input capture A By compare match/input capture B Synchronous clear Complementary PWM mode Reset-synchronized PWM mode Buffering (BRA) CMD1 = 1 CMD0 = 0 CMD1 = 1 CMD0 = 1 -- -- BFA4 = 1 -- Other bits unrestricted BFB4 = 1 -- Other bits unrestricted --
Illegal setting: CMD1 = 1 CMD0 = 0 Illegal setting: CMD1 = 1 CMD0 = 0 Illegal setting: CMD1 = 1 CMD0 = 0 CMD1 = 1 CMD0 = 0 CMD1 = 1 CMD0 = 1
*6
Buffering (BRB)
*1
8. 16-Bit Integrated Timer Unit (ITU)
Rev.2.00 Mar. 22, 2007 Page 285 of 684 REJ09B0352-0200
Legend: Notes: 1. 2. 3. 4. 5. 6.
Setting available (valid). -- Setting does not affect this mode. Master enable bit settings are valid only during waveform output. The input capture function cannot be used in PWM mode. If compare match A and compare match B occur simultaneously, the compare match signal is inhibited. Do not set both channels 3 and 4 for synchronous operation when complementary PWM mode is selected. When reset-synchronized PWM mode is selected, TCNT4 operates independently and the counter clearing function is available. Waveform output is not affected. In complementary PWM mode, select the same clock source for channels 3 and 4. TCR4 settings are valid in reset-synchronized PWM mode, but TCNT4 operates independently, without affecting waveform output.
8. 16-Bit Integrated Timer Unit (ITU)
Rev.2.00 Mar. 22, 2007 Page 286 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Section 9 Programmable Timing Pattern Controller
9.1 Overview
The H8/3022 Group has a built-in programmable timing pattern controller (TPC) * that provides pulse outputs by using the 16-bit integrated timer unit (ITU) as a time base. The TPC pulse outputs are divided into 4-bit groups (group 3 to group 0) that can operate simultaneously and independently. 9.1.1 Features
TPC features are listed below. * 15-bit output data Maximum 15-bit data can be output. TPC output can be enabled on a bit-by-bit basis. * Four output groups and one 3-bit output. Output trigger signals can be selected in 4-bit groups to provide up to three different 4-bit outputs and one 3-bit output. * Selectable output trigger signals Output trigger signals can be selected for each group from the compare-match signals of four ITU channels. * Non-overlap mode A non-overlap margin can be provided between pulse outputs. Note: * Note that since this LSI does not have a TP14 pin, it is a 15-bit programmable timing pattern controller (TPC).
Rev.2.00 Mar. 22, 2007 Page 287 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.1.2
Block Diagram
Figure 9.1 shows a block diagram of the TPC.
ITU compare match signals
PADDR Control logic NDERA TPMR
PBDDR NDERB TPCR
TP15 (TP14)* TP13 TP12 TP11 TP10 TP 9 TP 8 TP 7 TP 6 TP 5 TP 4 TP 3 TP 2 TP 1 TP 0
Pulse output pins, group 3 PBDR Pulse output pins, group 2 NDRB
Internal data bus
Pulse output pins, group 1 PADR Pulse output pins, group 0 NDRA
Note: * Since this LSI does not have this pin, this signal cannot be output to the outside. Legend TPMR: TPCR: NDERB: NDERA: PBDDR: PADDR: NDRB: NDRA: PBDR: PADR: TPC output mode register TPC output control register Next data enable register B Next data enable register A Port B data direction register Port A data direction register Next data register B Next data register A Port B data register Port A data register
Figure 9.1 TPC Block Diagram
Rev.2.00 Mar. 22, 2007 Page 288 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.1.3
Pin Configuration
Table 9.1 summarizes the TPC output pins. Table 9.1
Name TPC output 0 TPC output 1 TPC output 2 TPC output 3 TPC output 4 TPC output 5 TPC output 6 TPC output 7 TPC output 8 TPC output 9 TPC output 10 TPC output 11 TPC output 12 TPC output 13 (TPC output 14)* TPC output 15 Note: *
TPC Pins
Symbol TP0 TP1 TP2 TP3 TP4 TP5 TP6 TP7 TP8 TP9 TP10 TP11 TP12 TP13 (TP14)* TP15 I/O Output Output Output Output Output Output Output Output Output Output Output Output Output Output (Output)* Output Group 3 pulse output Group 2 pulse output Group 1 pulse output Function Group 0 pulse output
Since this LSI does not have this pin, this signal cannot be output to the outside.
Rev.2.00 Mar. 22, 2007 Page 289 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.1.4
Register Configuration
Table 9.2 summarizes the TPC registers. Table 9.2
Address* H'FFD1 H'FFD3 H'FFD4 H'FFD6 H'FFA0 H'FFA1 H'FFA2 H'FFA3 H'FFA5/ H'FFA7* H'FFA4/ H'FFA6*
3 3 1
TPC Registers
Name Port A data direction register Port A data register Port B data direction register Port B data register TPC output mode register TPC output control register Next data enable register B Next data enable register A Next data register A Next data register B Abbreviation PADDR PADR PBDDR PBDR TPMR TPCR NDERB NDERA NDRA NDRB R/W W R/(W)* W R/(W)* R/W R/W R/W R/W R/W R/W
2 2
Initial Value H'00 H'00 H'00 H'00 H'F0 H'FF H'00 H'00 H'00 H'00
Notes: 1. Lower 16 bits of the address. 2. Bits used for TPC output cannot be written. 3. The NDRA address is H'FFA5 when the same output trigger is selected for TPC output groups 0 and 1 by settings in TPCR. When the output triggers are different, the NDRA address is H'FFA7 for group 0 and H'FFA5 for group 1. Similarly, the address of NDRB is H'FFA4 when the same output trigger is selected for TPC output groups 2 and 3 by settings in TPCR. When the output triggers are different, the NDRB address is H'FFA6 for group 2 and H'FFA4 for group 3.
Rev.2.00 Mar. 22, 2007 Page 290 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.2
9.2.1
Register Descriptions
Port A Data Direction Register (PADDR)
PADDR is an 8-bit write-only register that selects input or output for each pin in port A.
Bit Initial value Read/Write 7 0 W 6 0 W 5 0 W 4 0 W 3 0 W 2 0 W 1 0 W 0 0 W
PA 7 DDR PA 6 DDR PA 5 DDR PA 4 DDR PA 3 DDR PA 2 DDR PA 1 DDR PA 0 DDR
Port A data direction 7 to 0 These bits select input or output for port A pins
Port A is multiplexed with pins TP7 to TP0. Bits corresponding to pins used for TPC output must be set to 1. For further information about PADDR, see section 7.10, Port A. 9.2.2 Port A Data Register (PADR)
PADR is an 8-bit readable/writable register that stores TPC output data for groups 0 and 1, when these TPC output groups are used.
Bit Initial value Read/Write 7 PA 7 0 R/(W) * 6 PA 6 0 R/(W) * 5 PA 5 0 R/(W) * 4 PA 4 0 R/(W) * 3 PA 3 0 R/(W) * 2 PA 2 0 R/(W) * 1 PA 1 0 R/(W) * 0 PA 0 0 R/(W) *
Port A data 7 to 0 These bits store output data for TPC output groups 0 and 1 Note: * Bits selected for TPC output by NDERA settings become read-only bits.
For further information about PADR, see section 7.10, Port A.
Rev.2.00 Mar. 22, 2007 Page 291 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.2.3
Port B Data Direction Register (PBDDR)
PBDDR is an 8-bit write-only register that selects input or output for each pin in port B.
Bit Initial value Read/Write 7 PB7 DDR 0 W 6 -- 0 W 5 0 W 4 0 W 3 0 W 2 0 W 1 0 W 0 0 W
PB5 DDR PB4 DDR PB3 DDR PB2 DDR PB1 DDR PB0 DDR
Reserved bit
Port B data direction 7, 5 to 0 These bits select input or output for port B pins
Port B is multiplexed with pins TP15, TP13 to TP8. Bits corresponding to pins used for TPC output must be set to 1. For further information about PBDDR, see section 7.11, Port B. 9.2.4 Port B Data Register (PBDR)
PBDR is an 8-bit readable/writable register that stores TPC output data for groups 2 and 3, when these TPC output groups are used.
Bit Initial value Read/Write 7 PB 7 0 R/(W)* 6 -- 0 R/(W)* 5 PB 5 0 R/(W)* 4 PB 4 0 R/(W)* 3 PB 3 0 R/(W)* 2 PB 2 0 R/(W)* 1 PB 1 0 R/(W)* 0 PB 0 0 R/(W)*
Reserved bit
Port B data 7, 5 to 0 These bits store output data for TPC output groups 2 and 3
Note: * Bits selected for TPC output by NDERB settings become read-only bits.
For further information about PBDR, see section 7.11, Port B.
Rev.2.00 Mar. 22, 2007 Page 292 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.2.5
Next Data Register A (NDRA)
NDRA is an 8-bit readable/writable register that stores the next output data for TPC output groups 1 and 0 (pins TP7 to TP0). During TPC output, when an ITU compare match event specified in TPCR occurs, NDRA contents are transferred to the corresponding bits in PADR. The address of NDRA differs depending on whether TPC output groups 0 and 1 have the same output trigger or different output triggers. NDRA is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in software standby mode. Same Trigger for TPC Output Groups 0 and 1: If TPC output groups 0 and 1 are triggered by the same compare match event, the NDRA address is H'FFA5. The upper 4 bits belong to group 1 and the lower 4 bits to group 0. Address H'FFA7 consists entirely of reserved bits that cannot be modified and always read 1. Address H'FFA5
Bit Initial value Read/Write 7 NDR7 0 R/W 6 NDR6 0 R/W 5 NDR5 0 R/W 4 NDR4 0 R/W 3 NDR3 0 R/W 2 NDR2 0 R/W 1 NDR1 0 R/W 0 NDR0 0 R/W
Next data 7 to 4 These bits store the next output data for TPC output group 1
Next data 3 to 0 These bits store the next output data for TPC output group 0
Address H'FFA7
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 -- 1 -- 2 -- 1 -- 1 -- 1 -- 0 -- 1 --
Reserved bits
Rev.2.00 Mar. 22, 2007 Page 293 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Different Triggers for TPC Output Groups 0 and 1: If TPC output groups 0 and 1 are triggered by different compare match events, the address of the upper 4 bits of NDRA (group 1) is H'FFA5 and the address of the lower 4 bits (group 0) is H'FFA7. Bits 3 to 0 of address H'FFA5 and bits 7 to 4 of address H'FFA7 are reserved bits that cannot be modified and always read 1. Address H'FFA5
Bit Initial value Read/Write 7 NDR7 0 R/W 6 NDR6 0 R/W 5 NDR5 0 R/W 4 NDR4 0 R/W 3 -- 1 -- 2 -- 1 -- 1 -- 1 -- 0 -- 1 --
Next data 7 to 4 These bits store the next output data for TPC output group 1
Reserved bits
Address H'FFA7
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 NDR3 0 R/W 2 NDR2 0 R/W 1 NDR1 0 R/W 0 NDR0 0 R/W
Reserved bits
Next data 3 to 0 These bits store the next output data for TPC output group 0
Rev.2.00 Mar. 22, 2007 Page 294 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.2.6
Next Data Register B (NDRB)
NDRB is an 8-bit readable/writable register that stores the next output data for TPC output groups 3 and 2 (pins TP15 to TP8)*. During TPC output, when an ITU compare match event specified in TPCR occurs, NDRB contents are transferred to the corresponding bits in PBDR. The address of NDRB differs depending on whether TPC output groups 3 and 2 have the same output trigger or different output triggers. NDRB is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in software standby mode. Note: Since this LSI does not have a TP14 pin, the TP14 signal cannot be output to the outside. Same Trigger for TPC Output Groups 3 and 2: If TPC output groups 3 and 2 are triggered by the same compare match event, the NDRB address is H'FFA4. The upper 4 bits belong to group 3 and the lower 4 bits to group 2. Address H'FFA6 consists entirely of reserved bits that cannot be modified and always read 1. Address H'FFA4
Bit Initial value Read/Write 7 NDR15 0 R/W 6 NDR14 0 R/W 5 NDR13 0 R/W 4 NDR12 0 R/W 3 NDR11 0 R/W 2 NDR10 0 R/W 1 NDR9 0 R/W 0 NDR8 0 R/W
Next data 15 to 12 These bits store the next output data for TPC output group 3
Next data 11 to 8 These bits store the next output data for TPC output group 2
Address H'FFA6
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 -- 1 -- 2 -- 1 -- 1 -- 1 -- 0 -- 1 --
Reserved bits
Rev.2.00 Mar. 22, 2007 Page 295 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Different Triggers for TPC Output Groups 3 and 2: If TPC output groups 3 and 2 are triggered by different compare match events, the address of the upper 4 bits of NDRB (group 3)* is H'FFA4 and the address of the lower 4 bits (group 2) is H'FFA6. Bits 3 to 0 of address H'FFA4 and bits 7 to 4 of address H'FFA6 are reserved bits that cannot be modified and always read 1. Note: * Since this LSI does not have a TP14 pin, the TP14 signal cannot be output off-chip. Address H'FFA4
Bit Initial value Read/Write 7 NDR15 0 R/W 6 NDR14 0 R/W 5 NDR13 0 R/W 4 NDR12 0 R/W 3 -- 1 -- 2 -- 1 -- 1 -- 1 -- 0 -- 1 --
Next data 15 to 12 These bits store the next output data for TPC output group 3
Reserved bits
Address H'FFA6
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 NDR11 0 R/W 2 NDR10 0 R/W 1 NDR9 0 R/W 0 NDR8 0 R/W
Reserved bits
Next data 11 to 8 These bits store the next output data for TPC output group 2
Rev.2.00 Mar. 22, 2007 Page 296 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.2.7
Next Data Enable Register A (NDERA)
NDERA is an 8-bit readable/writable register that enables or disables TPC output groups 1 and 0 (TP7 to TP0) on a bit-by-bit basis.
Bit Initial value Read/Write 7 NDER7 0 R/W 6 NDER6 0 R/W 5 NDER5 0 R/W 4 NDER4 0 R/W 3 NDER3 0 R/W 2 NDER2 0 R/W 1 NDER1 0 R/W 0 NDER0 0 R/W
Next data enable 7 to 0 These bits enable or disable TPC output groups 1 and 0
If a bit is enabled for TPC output by NDERA, then when the ITU compare match event selected in the TPC output control register (TPCR) occurs, the NDRA value is automatically transferred to the corresponding PADR bit, updating the output value. If TPC output is disabled, the bit value is not transferred from NDRA to PADR and the output value does not change. NDERA is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in software standby mode. Bits 7 to 0--Next Data Enable 7 to 0 (NDER7 to NDER0): These bits enable or disable TPC output groups 1 and 0 (TP7 to TP0) on a bit-by-bit basis.
Bits 7 to 0 NDER7 to NDER0 0 1 Description TPC outputs TP7 to TP0 are disabled (NDR7 to NDR0 are not transferred to PA7 to PA0) TPC outputs TP7 to TP0 are enabled (NDR7 to NDR0 are transferred to PA7 to PA0) (Initial value)
Rev.2.00 Mar. 22, 2007 Page 297 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.2.8
Next Data Enable Register B (NDERB)
NDERB is an 8-bit readable/writable register that enables or disables TPC output groups 3 and 2 (TP15 to TP8)* on a bit-by-bit basis.
Bit Initial value Read/Write 7 0 R/W 6 0 R/W 5 0 R/W 4 0 R/W 3 0 R/W 2 0 R/W 1 0 R/W 0 NDER8 0 R/W
NDER15 NDER14 NDER13 NDER12 NDER11 NDER10 NDER9
Next data enable 15 to 8 These bits enable or disable TPC output groups 3 and 2
If a bit is enabled for TPC output by NDERB, then when the ITU compare match event selected in the TPC output control register (TPCR) occurs, the NDRB value is automatically transferred to the corresponding PBDR bit, updating the output value. If TPC output is disabled, the bit value is not transferred from NDRB to PBDR and the output value does not change. NDERB is initialized to H'00 by a reset and in hardware standby mode. It is not initialized in software standby mode. Bits 7 to 0--Next Data Enable 15 to 8 (NDER15 to NDER8): These bits enable or disable TPC output groups 3 and 2 (TP15 to TP8)* on a bit-by-bit basis.
Bits 7 to 0 NDER15 to NDER8 0 1 Description TPC outputs TP15 to TP8 are disabled (NDR15 to NDR8 are not transferred to PB7 to PB0) TPC outputs TP15 to TP8 are enabled (NDR15 to NDR8 are transferred to PB7 to PB0) * Since this LSI does not have a TP14 pin, the TP14 signal cannot be output to the outside. (Initial value)
Note:
Rev.2.00 Mar. 22, 2007 Page 298 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.2.9
TPC Output Control Register (TPCR)
TPCR is an 8-bit readable/writable register that selects output trigger signals for TPC outputs on a group-by-group basis.
Bit Initial value Read/Write 7 1 R/W 6 1 R/W 5 1 R/W 4 1 R/W 3 1 R/W 2 1 R/W 1 1 R/W 0 1 R/W
G3CMS1 G3CMS0 G2CMS1 G2CMS0 G1CMS1 G1CMS0 G0CMS1 G0CMS0
Group 3 compare match select 1 and 0 These bits select the compare match Group 2 compare event that triggers TPC output group 3 match select 1 and 0 These bits select (TP15 to TP12 ) the compare match event that triggers Group 1 compare TPC output group 2 match select 1 and 0 These bits select (TP11 to TP 8 ) the compare match event that triggers Group 0 compare TPC output group 1 match select 1 and 0 These bits select (TP7 to TP4 ) the compare match event that triggers TPC output group 0 (TP3 to TP0 ) Note: * Since this LSI does not have a TP14 pin, the TP14 signal cannot be output to the outside.
TPCR is initialized to H'FF by a reset and in hardware standby mode. It is not initialized in software standby mode.
Rev.2.00 Mar. 22, 2007 Page 299 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Bits 7 and 6--Group 3 Compare Match Select 1 and 0 (G3CMS1, G3CMS0): These bits select the compare match event that triggers TPC output group 3 (TP15 to TP12)*.
Bit 7 G3CMS1 0 Bit6 G3CMS0 0 1 1 0 1 Note: * Description TPC output group 3 (TP15 to TP12)* is triggered by compare match in ITU channel 0 TPC output group 3 (TP15 to TP12)* is triggered by compare match in ITU channel 1 TPC output group 3 (TP15 to TP12)* is triggered by compare match in ITU channel 2 TPC output group 3 (TP15 to TP12)* is triggered by compare match in ITU channel 3 (Initial value)
Since this LSI does not have a TP14 pin, the TP14 signal cannot be output off-chip.
Bits 5 and 4--Group 2 Compare Match Select 1 and 0 (G2CMS1, G2CMS0): These bits select the compare match event that triggers TPC output group 2 (TP11 to TP8).
Bit 5 G2CMS1 0 Bit4 G2CMS0 0 1 1 0 1 Description TPC output group 2 (TP11 to TP8) is triggered by compare match in ITU channel 0 TPC output group 2 (TP11 to TP8) is triggered by compare match in ITU channel 1 TPC output group 2 (TP11 to TP8) is triggered by compare match in ITU channel 2 TPC output group 2 (TP11 to TP8) is triggered (Initial value) by compare match in ITU channel 3
Rev.2.00 Mar. 22, 2007 Page 300 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Bits 3 and 2--Group 1 Compare Match Select 1 and 0 (G1CMS1, G1CMS0): These bits select the compare match event that triggers TPC output group 1 (TP7 to TP4).
Bit 3 G1CMS1 0 Bit2 G1CMS0 0 1 1 0 1 Description TPC output group 1 (TP7 to TP4) is triggered by compare match in ITU channel 0 TPC output group 1 (TP7 to TP4) is triggered by compare match in ITU channel 1 TPC output group 1 (TP7 to TP4) is triggered by compare match in ITU channel 2 TPC output group 1 (TP7 to TP4) is triggered by compare match in ITU channel 3 (Initial value)
Bits 1 and 0--Group 0 Compare Match Select 1 and 0 (G0CMS1, G0CMS0): These bits select the compare match event that triggers TPC output group 0 (TP3 to TP0).
Bit1 G0CMS1 0 Bit0 G0CMS0 0 1 1 0 1 Description TPC output group 0 (TP3 to TP0) is triggered by compare match in ITU channel 0 TPC output group 0 (TP3 to TP0) is triggered by compare match in ITU channel 1 TPC output group 0 (TP3 to TP0) is triggered by compare match in ITU channel 2 TPC output group 0 (TP3 to TP0) is triggered by compare match in ITU channel 3 (Initial value)
Rev.2.00 Mar. 22, 2007 Page 301 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.2.10
TPC Output Mode Register (TPMR)
TPMR is an 8-bit readable/writable register that selects normal or non-overlapping TPC output for each group.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 0 R/W 2 0 R/W 1 0 R/W 0 0 R/W
G3NOV G2NOV
G1NOV G0NOV
Reserved bits Group 3 non-overlap Selects non-overlapping TPC output for group 3 (TP15 to TP12) Group 2 non-overlap Selects non-overlapping TPC output for group 2 (TP11 to TP8 ) Group 1 non-overlap Selects non-overlapping TPC output for group 1 (TP7 to TP4 ) Group 0 non-overlap Selects non-overlapping TPC output for group 0 (TP3 to TP0 ) Note: * Since this LSI does not have a TP14 pin, the TP14 signal cannot be output to the outside.
The output trigger period of a non-overlapping TPC output waveform is set in general register B (GRB) in the ITU channel selected for output triggering. The non-overlap margin is set in general register A (GRA). The output values change at compare match A and B. For details see section 9.3.4, Non-Overlapping TPC Output. TPMR is initialized to H'F0 by a reset and in hardware standby mode. It is not initialized in software standby mode. Bits 7 to 4--Reserved: These bits cannot be modified and are always read as 1.
Rev.2.00 Mar. 22, 2007 Page 302 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Bit 3--Group 3 Non-Overlap (G3NOV): Selects normal or non-overlapping TPC output for group 3 (TP15 to TP12)*.
Bit 3 G3NOV 0 1 Description Normal TPC output in group 3 (output values change at compare match A in the selected ITU channel) Non-overlapping TPC output in group 3 (independent 1 and 0 output at compare match A and B in the selected ITU channel) (Initial value)
Note: * Since this LSI does not have a TP14 pin, the TP14 signal cannot be output off-chip. Bit 2--Group 2 Non-Overlap (G2NOV): Selects normal or non-overlapping TPC output for group 2 (TP11 to TP8).
Bit 2 G2NOV 0 1 Description Normal TPC output in group 2 (output values change at compare match A in the selected ITU channel) Non-overlapping TPC output in group 2 (independent 1 and 0 output at compare match A and B in the selected ITU channel) (Initial value)
Bit 1--Group 1 Non-Overlap (G1NOV): Selects normal or non-overlapping TPC output for group 1 (TP7 to TP4).
Bit 1 G1NOV 0 1 Description Normal TPC output in group 1 (output values change at compare match A in the selected ITU channel) Non-overlapping TPC output in group 1 (independent 1 and 0 output at compare match A and B in the selected ITU channel) (Initial value)
Rev.2.00 Mar. 22, 2007 Page 303 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Bit 0--Group 0 Non-Overlap (G0NOV): Selects normal or non-overlapping TPC output for group 0 (TP3 to TP0).
Bit 0 G0NOV 0 1 Description Normal TPC output in group 0 (output values change at compare match A in the selected ITU channel) Non-overlapping TPC output in group 0 (independent 1 and 0 output at compare match A and B in the selected ITU channel) (Initial value)
Rev.2.00 Mar. 22, 2007 Page 304 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.3
9.3.1
Operation
Overview
When corresponding bits in PADDR or PBDDR and NDERA or NDERB are set to 1, TPC output is enabled. The TPC output initially consists of the corresponding PADR or PBDR contents. When a compare-match event selected in TPCR occurs, the corresponding NDRA or NDRB bit contents are transferred to PADR or PBDR to update the output values. Figure 9.2 illustrates the TPC output operation. Table 9.3 summarizes the TPC operating conditions.
DDR Q
NDER Q Output trigger signal
C Q TPC output pin DR D Q NDR D Internal data bus
Figure 9.2 TPC Output Operation Table 9.3
NDER 0
TPC Operating Conditions
DDR 0 1 Pin Function Generic input port Generic output port Generic input port (but the DR bit is a read-only bit, and when compare match occurs, the NDR bit value is transferred to the DR bit) TPC pulse output
1
0 1
Sequential output of up to 16-bit patterns is possible by writing new output data to NDRA and NDRB before the next compare match. For information on non-overlapping operation, see section 9.3.4, Non-Overlapping TPC Output.
Rev.2.00 Mar. 22, 2007 Page 305 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.3.2
Output Timing
If TPC output is enabled, NDRA/NDRB contents are transferred to PADR/PBDR and output when the selected compare match event occurs. Figure 9.3 shows the timing of these operations for the case of normal output in groups 0 and 1, triggered by compare match A.
TCNT
N
N+1
GRA Compare match A signal
N
NDRA
n
PADR TP0 to TP7
m m
n n
Figure 9.3 Timing of Transfer of Next Data Register Contents and Output (Example)
Rev.2.00 Mar. 22, 2007 Page 306 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.3.3
Normal TPC Output
Sample Setup Procedure for Normal TPC Output: Figure 9.4 shows a sample procedure for setting up normal TPC output.
Normal TPC output
Select GR functions Set GRA value ITU setup Select counting operation Select interrupt request
1 2 3 4
Set initial output data Select port output Port and TPC setup Enable TPC output Select TPC output trigger Set next TPC output data
5 6 7 8 9
Set TIOR to make GRA an output compare register (with output inhibited). 2. Set the TPC output trigger period. 3. Select the counter clock source with bits TPSC2 to TPSC0 in TCR. Select the counter clear source with bits CCLR1 and CCLR0. 4. Enable the IMFA interrupt in TIER. 5. Set the initial output values in the DR bits of the input/output port pins to be used for TPC output. 6. Set the DDR bits of the input/output port pins to be used for TPC output to 1. 7. Set the NDER bits of the pins to be used for TPC output to 1. 8. Select the ITU compare match event to be used as the TPC output trigger in TPCR. 9. Set the next TPC output values in the NDR bits. 10. Set the STR bit to 1 in TSTR to start the timer counter. 11. At each IMFA interrupt, set the next output values in the NDR bits.
1.
ITU setup
Start counter
10
Compare match? Yes Set next TPC output data
No
11
Figure 9.4 Setup Procedure for Normal TPC Output (Example)
Rev.2.00 Mar. 22, 2007 Page 307 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Example of Normal TPC Output (Example of Five-Phase Pulse Output): Figure 9.5 shows an example in which the TPC is used for cyclic five-phase pulse output.
TCNT value TCNT GRA Compare match
H'0000 NDRA 80 C0 40 60 20 30 10 18 08 88 80 C0 40
Time
PADR
00
80
C0
40
60
20
30
10
18
08
88
80
C0
TP7
TP6 TP5 TP4
TP3
* * * *
The ITU channel to be used as the output trigger channel is set up so that GRA is an output compare register and the counter will be cleared by compare match A. The trigger period is set in GRA. The IMIEA bit is set to 1 in TIER to enable the compare match A interrupt. H'F8 is written in PADDR and NDERA, and bits G1CMS1, G1CMS0, G0CMS1, and G0CMS0 are set in TPCR to select compare match in the ITU channel set up in step 1 as the output trigger. Output data H'80 is written in NDRA. The timer counter in this ITU channel is started. When compare match A occurs, the NDRA contents are transferred to PADR and output. The compare match/input capture A (IMFA) interrupt service routine writes the next output data (H'C0) in NDRA. Five-phase overlapping pulse output (one or two phases active at a time) can be obtained by writing H'40, H'60, H'20, H'30, H'10, H'18, H'08, H'88... at successive IMFA interrupts.
Figure 9.5 Normal TPC Output Example (Five-Phase Pulse Output)
Rev.2.00 Mar. 22, 2007 Page 308 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.3.4
Non-Overlapping TPC Output
Sample Setup Procedure for Non-Overlapping TPC Output: Figure 9.6 shows a sample procedure for setting up non-overlapping TPC output.
Non-overlapping TPC output Select GR functions Set GR values ITU setup Select counting operation Select interrupt requests 3 4 1 2 1. Set TIOR to make GRA and GRB output compare registers (with output inhibited). 2. Set the TPC output trigger period in GRB and the non-overlap margin in GRA. 3. Select the counter clock source with bits TPSC2 to TPSC0 in TCR. Select the counter clear source with bits CCLR1 and CCLR0. 4. Enable the IMFA interrupt in TIER. 5. Set the initial output values in the DR bits of the input/output port pins to be used for TPC output. 6. Set the DDR bits of the input/output port pins to be used for TPC output to 1. 7. Set the NDER bits of the pins to be used for TPC output to 1. 8. In TPCR, select the ITU compare match event to be used as the TPC output trigger. 9. In TPMR, select the groups that will operate in non-overlap mode. 10. Set the next TPC output values in the NDR bits. 11. Set the STR bit to 1 in TSTR to start the timer counter. 12. At each IMFA interrupt, write the next output value in the NDR bits.
Set initial output data Set up TPC output Enable TPC transfer Port and TPC setup Select TPC transfer trigger Select non-overlapping groups Set next TPC output data
5 6 7 8 9 10
ITU setup
Start counter
11
Compare match A? Yes Set next TPC output data
No
12
Figure 9.6 Setup Procedure for Non-Overlapping TPC Output (Example)
Rev.2.00 Mar. 22, 2007 Page 309 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Example of Non-Overlapping TPC Output (Example of Four-Phase Complementary NonOverlapping Output): Figure 9.7 shows an example of the use of TPC output for four-phase complementary non-overlapping pulse output.
TCNT value GRB GRA H'0000 NDRA 95 65 59 56 95 65 Time TCNT
PADR
00
95
05
65
41
59
50
56
14
95
05
65
Non-overlap margin TP7
TP6 TP5 TP4
TP3 TP2 TP1 TP0
* The ITU channel to be used as the output trigger channel is set up so that GRA and GRB are output
compare registers and the counter will be cleared by compare match B. The TPC output trigger period is set in GRB. The non-overlap margin is set in GRA. The IMIEA bit is set to 1 in TIER to enable IMFA interrupts. * H'FF is written in PADDR and NDERA, and bits G1CMS1, G1CMS0, G0CMS1, and G0CMS0 are set in TPCR to select compare match in the ITU channel set up in step 1 as the output trigger. Bits G1NOV and G0NOV are set to 1 in TPMR to select non-overlapping output. Output data H'95 is written in NDRA. * The timer counter in this ITU channel is started. When compare match B occurs, outputs change from 1 to 0. When compare match A occurs, outputs change from 0 to 1 (the change from 0 to 1 is delayed by the value of GRA). The IMFA interrupt service routine writes the next output data (H'65) in NDRA. * Four-phase complementary non-overlapping pulse output can be obtained by writing H'59, H'56, H'95... at successive IMFA interrupts.
Figure 9.7 Non-Overlapping TPC Output Example (Four-Phase Complementary Non-Overlapping Pulse Output)
Rev.2.00 Mar. 22, 2007 Page 310 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.3.5
TPC Output Triggering by Input Capture
TPC output can be triggered by ITU input capture as well as by compare match. If GR functions as an input capture register in the ITU channel selected in TPCR, TPC output will be triggered by the input capture signal. Figure 9.8 shows the timing.
TIOC pin Input capture signal NDR N
DR
M
N
Figure 9.8 TPC Output Triggering by Input Capture (Example)
Rev.2.00 Mar. 22, 2007 Page 311 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
9.4
9.4.1
Usage Notes
Operation of TPC Output Pins
TP0 to TP15* are multiplexed with ITU pin functions. When ITU output is enabled, the corresponding pins cannot be used for TPC output. The data transfer from NDR bits to DR bits takes place, however, regardless of the usage of the pin. Pin functions should be changed only under conditions in which the output trigger event will not occur. Note: * Since this LSI does not have a TP14 pin, the TP14 signal cannot be output to the outside. 9.4.2 Note on Non-Overlapping Output
During non-overlapping operation, the transfer of NDR bit values to DR bits takes place as follows. 1. NDR bits are always transferred to DR bits at compare match A. 2. At compare match B, NDR bits are transferred only if their value is 0. Bits are not transferred if their value is 1. Figure 9.9 illustrates the non-overlapping TPC output operation.
DDR Q
NDER Q Compare match A Compare match B
C Q TPC output pin DR D Q NDR D
Figure 9.9 Non-Overlapping TPC Output
Rev.2.00 Mar. 22, 2007 Page 312 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Therefore, 0 data can be transferred ahead of 1 data by making compare match B occur before compare match A. NDR contents should not be altered during the interval from compare match B to compare match A (the non-overlap margin). This can be accomplished by having the IMFA interrupt service routine write the next data in NDR. The next data must be written before the next compare match B occurs. Figure 9.10 shows the timing relationships.
Compare match A Compare match B NDR write NDR write
NDR
DR 0 output 0/1 output Write to NDR in this interval Do not write to NDR in this interval Do not write to NDR in this interval 0 output 0/1 output Write to NDR in this interval
Figure 9.10 Non-Overlapping Operation and NDR Write Timing
Rev.2.00 Mar. 22, 2007 Page 313 of 684 REJ09B0352-0200
9. Programmable Timing Pattern Controller
Rev.2.00 Mar. 22, 2007 Page 314 of 684 REJ09B0352-0200
10. Watchdog Timer
Section 10 Watchdog Timer
10.1 Overview
The H8/3022 Group has an on-chip watchdog timer (WDT). The WDT has two selectable functions: it can operate as a watchdog timer to supervise system operation, or it can operate as an interval timer. As a watchdog timer, it generates a reset signal for the H8/3022 Group chip if a system crash allows the timer counter (TCNT) to overflow before being rewritten. In interval timer operation, an interval timer interrupt is requested at each TCNT overflow. 10.1.1 Features
WDT features are listed below. * Selection of eight counter clock sources /2, /32, /64, /128, /256, /512, /2048, or /4096 * Interval timer option * Timer counter overflow generates a reset signal or interrupt. The reset signal is generated in watchdog timer operation. An interval timer interrupt is generated in interval timer operation. * Watchdog timer reset signal resets the entire H8/3022 Group chip internally, and can also be output externally.* The reset signal generated by timer counter overflow during watchdog timer operation resets the entire H8/3022 Group internally. An external reset signal can be output from the RESO pin to reset other system devices simultaneously. Note: * The RESO pin of the mask ROM version is the dedicated FWE input pin of the FZTAT version. Therefore, the F-ZTAT version cannot output the reset signal to the outside.
Rev.2.00 Mar. 22, 2007 Page 315 of 684 REJ09B0352-0200
10. Watchdog Timer
10.1.2
Block Diagram
Figure 10.1 shows a block diagram of the WDT.
Overflow TCNT Interrupt signal Interrupt (interval timer) control TCSR Read/ write control
Internal data bus
RSTCSR
Internal clock sources /2 /32 /64 Clock Clock selector /128 /256 /512 /2048 /4096
Reset (internal, external)
Reset control
Legend TCNT: Timer counter TCSR: Timer control/status register RSTCSR: Reset control/status register
Figure 10.1 WDT Block Diagram 10.1.3 Pin Configuration
1
Table 10.1 describes the WDT output pin.* Table 10.1 WDT Pin
Name Reset output Abbreviation RESO I/O
Function
2
Output*
External output of the watchdog timer reset signal
Notes: 1. Shows the masked ROM version pin. The F-ZTAT does not have any pins used by the WDT. For F-ZTAT version, see section 15.11 Notes on Flash Memory Programming/Erasing. 2. Open-drain output. Externally pull-up to Vcc whether or not the reset output is used
Rev.2.00 Mar. 22, 2007 Page 316 of 684 REJ09B0352-0200
10. Watchdog Timer
10.1.4
Register Configuration
Table 10.2 summarizes the WDT registers. Table 10.2 WDT Registers
Address* Write* H'FFA8
2 1
Read H'FFA8 H'FFA9
Name Timer control/status register Timer counter Reset control/status register
Abbreviation TCSR TCNT RSTCSR
R/W R/(W)* R/W R/(W)*
3 3
Initial Value H'18 H'00 H'3F
H'FFAA
H'FFAB
Notes: 1. Lower 16 bits of the address. 2. Write word data starting at this address. 3. Only 0 can be written in bit 7 to clear the flag.
Rev.2.00 Mar. 22, 2007 Page 317 of 684 REJ09B0352-0200
10. Watchdog Timer
10.2
10.2.1
Register Descriptions
Timer Counter (TCNT)
TCNT is an 8-bit readable and writable* up-counter.
Bit Initial value Read/Write 7 0 R/W 6 0 R/W 5 0 R/W 4 0 R/W 3 0 R/W 2 0 R/W 1 0 R/W 0 0 R/W
When the TME bit is set to 1 in TCSR, TCNT starts counting pulses generated from an internal clock source selected by bits CKS2 to CKS0 in TCSR. When the count overflows (changes from H'FF to H'00), the OVF bit is set to 1 in TCSR. TCNT is initialized to H'00 by a reset and when the TME bit is cleared to 0. Note: * TCNT is write-protected by a password. For details see section 10.2.4, Notes on Register Access.
Rev.2.00 Mar. 22, 2007 Page 318 of 684 REJ09B0352-0200
10. Watchdog Timer
10.2.2
Timer Control/Status Register (TCSR)
1
TCSR is an 8-bit readable and writable* register. Its functions include selecting the timer mode and clock source.
Bit Initial value Read/Write 7 OVF 0 R/(W)*2 6 WT/IT 0 R/W 5 TME 0 R/W 4 -- 1 -- 3 -- 1 -- 2 CKS2 0 R/W 1 CKS1 0 R/W 0 CKS0 0 R/W
Clock select These bits select the TCNT clock source Reserved bits Timer enable Selects whether TCNT runs or halts Timer mode select Selects the mode Overflow flag Status flag indicating overflow
Bits 7 to 5 are initialized to 0 by a reset and in standby mode. Bits 2 to 0 are initialized to 0 by a reset. In software standby mode bits 2 to 0 are not initialized, but retain their previous values. Notes: 1. TCSR is write-protected by a password. For details see section 10.2.4, Notes on Register Access. 2. Only 0 can be written to clear the flag.
Rev.2.00 Mar. 22, 2007 Page 319 of 684 REJ09B0352-0200
10. Watchdog Timer
Bit 7--Overflow Flag (OVF): This status flag indicates that the timer counter has overflowed from H'FF to H'00.
Bit 7 OVF 0 1 Description [Clearing condition] Cleared by reading OVF when OVF = 1, then writing 0 in OVF [Setting condition] Set when TCNT changes from H'FF to H'00 (Initial value)
Bit 6--Timer Mode Select (WT/IT): Selects whether to use the WDT as a watchdog timer or interval timer. If used as an interval timer, the WDT generates an interval timer interrupt request when TCNT overflows. If used as a watchdog timer, the WDT generates a reset signal when TCNT overflows.
Bit 6 WT/IT 0 1 Description Interval timer: requests interval timer interrupts Watchdog timer: generates a reset signal (Initial value)
Bit 5--Timer Enable (TME): Selects whether TCNT runs or is halted.
Bit 5 TME 0 1 Description TCNT is initialized to H'00 and halted TCNT is counting (Initial value)
Bits 4 and 3--Reserved: These bits cannot be modified and are always read as 1.
Rev.2.00 Mar. 22, 2007 Page 320 of 684 REJ09B0352-0200
10. Watchdog Timer
Bits 2 to 0--Clock Select 2 to 0 (CKS2/1/0): These bits select one of eight internal clock sources, obtained by prescaling the system clock (), for input to TCNT.
Bit 2 CKS2 0 Bit 1 CKS1 0 Bit 0 CKS0 0 1 1 0 1 1 0 0 1 1 0 1 Description /2 /32 /64 /128 /256 /512 /2048 /4096 (Initial value)
10.2.3
Reset Control/Status Register (RSTCSR)
1
RSTCSR is an 8-bit readable and writable* register that indicates when a reset signal has been generated by watchdog timer overflow, and controls external output of the reset signal.
Bit Initial value Read/Write 7 WRST 0 R/(W)*2 6 RSTOE 0 R/W 5 -- 1 -- 4 -- 1 -- 3 -- 1 -- 2 -- 1 -- 1 -- 1 -- 0 -- 1 --
Reserved bits Reset output enable*3 Enables or disables external output of the reset signal Watchdog timer reset Indicates that a reset signal has been generated
Bits 7 and 6 are initialized by input of a reset signal at the RES pin. They are not initialized by reset signals generated by watchdog timer overflow. Notes: 1. RSTCSR is write-protected by a password. For details see section 10.2.4, Notes on Register Access. 2. Only 0 can be written in bit 7 to clear the flag. 3. With the mask ROM version, enable and disable can be set. With the F-ZTAT version, do not set enable.
Rev.2.00 Mar. 22, 2007 Page 321 of 684 REJ09B0352-0200
10. Watchdog Timer
Bit 7--Watchdog Timer Reset (WRST): During watchdog timer operation, this bit indicates that TCNT has overflowed and generated a reset signal. This reset signal resets the entire chip 1 internally. If bit RSTOE is set to 1, this reset signal is also output (low) at the RESO pin* to initialize external system devices.
Bit 7 WRST 0 Description [Clearing condition] (1) Cleared to 0 by reset signal input at RES pin (2) Cleared by reading WRST when WRST = 1, then writing 0 in WERST 1 [Setting condition] Set when TCNT overflow generates a reset signal during watchdog timer operation (Initial value)
Bit 6--Reset Output Enable (RSTOE): Enables or disables external output at the RESO pin* of the reset signal generated if TCNT overflows during watchdog timer operation.
1
Bit 6 RSTOE 0 1
Description Reset signal is not output externally Reset signal is output externally*
2
(Initial value)
Bits 5 to 0--Reserved: These bits cannot be modified and are always read as 1. Notes: 1. Mask ROM version. Dedicated FWE input pin for F-ZTAT version. 2. Mask ROM version. Do not set to 1 with the F-ZTAT version.
Rev.2.00 Mar. 22, 2007 Page 322 of 684 REJ09B0352-0200
10. Watchdog Timer
10.2.4
Notes on Register Access
The watchdog timer's TCNT, TCSR, and RSTCSR registers differ from other registers in being more difficult to write. The procedures for writing and reading these registers are given below. Writing to TCNT and TCSR: These registers must be written by a word transfer instruction. They cannot be written by byte instructions. Figure 10.2 shows the format of data written to TCNT and TCSR. TCNT and TCSR both have the same write address. The write data must be contained in the lower byte of the written word. The upper byte must contain H'5A (password for TCNT) or H'A5 (password for TCSR). This transfers the write data from the lower byte to TCNT or TCSR.
TCNT write Address H'FFA8 * 15 H'5A 87 Write data 0
TCSR write Address H'FFA8 *
15 H'A5
87 Write data
0
Note: * Lower 16 bits of the address.
Figure 10.2 Format of Data Written to TCNT and TCSR
Rev.2.00 Mar. 22, 2007 Page 323 of 684 REJ09B0352-0200
10. Watchdog Timer
Writing to RSTCSR: RSTCSR must be written by a word transfer instruction. It cannot be written by byte transfer instructions. Figure 10.3 shows the format of data written to RSTCSR. To write 0 in the WRST bit, the write data must have H'A5 in the upper byte and H'00 in the lower byte. The H'00 in the lower byte clears the WRST bit in RSTCSR to 0. To write to the RSTOE bit, the upper byte must contain H'5A and the lower byte must contain the write data. Writing this word transfers a write data value into the RSTOE bit.
Writing 0 in WRST bit Address H'FFAA* 15 H'A5 87 H'00 0
Writing to RSTOE bit Address H'FFAA*
15 H'5A
87 Write data
0
Note: * Lower 16 bits of the address.
Figure 10.3 Format of Data Written to RSTCSR Reading TCNT, TCSR, and RSTCSR: These registers are read like other registers. Byte access instructions can be used. The read addresses are H'FFA8 for TCSR, H'FFA9 for TCNT, and H'FFAB for RSTCSR, as listed in table 10.3. Table 10.3 Read Addresses of TCNT, TCSR, and RSTCSR
Address* H'FFA8 H'FFA9 H'FFAB Note: * Register TCSR TCNT RSTCSR Lower 16 bits of the address.
Rev.2.00 Mar. 22, 2007 Page 324 of 684 REJ09B0352-0200
10. Watchdog Timer
10.3
Operation
Operations when the WDT is used as a watchdog timer and as an interval timer are described below. 10.3.1 Watchdog Timer Operation
Figure 10.4 illustrates watchdog timer operation. To use the WDT as a watchdog timer, set the WT/IT and TME bits to 1 in TCSR. Software must prevent TCNT overflow by rewriting the TCNT value (normally by writing H'00) before overflow occurs. If TCNT fails to be rewritten and overflows due to a system crash etc., the H8/3022 Group is internally reset for a duration of 518 states. The watchdog reset signal can be externally output from the RESO pin* to reset external system devices. The reset signal is output externally for 132 states. External output can be enabled or disabled by the RSTOE bit in RSTCSR. A watchdog reset has the same vector as a reset generated by input at the RES pin. Software can distinguish a RES reset from a watchdog reset by checking the WRST bit in RSTCSR. If a RES reset and a watchdog reset occur simultaneously, the RES reset takes priority. Note: * Mask ROM version. Since the RES pin is a dedicated FWE input pin with the F-ZTAT version, the reset signal cannot be output to the outside.
Rev.2.00 Mar. 22, 2007 Page 325 of 684 REJ09B0352-0200
10. Watchdog Timer
WDT overflow
H'FF TCNT count value H'00
TME set to 1
OVF = 1 Start Internal reset signal H'00 written in TCNT Reset H'00 written in TCNT
518 states RESO
132 states
Figure 10.4 Watchdog Timer Operation (Mask ROM Version) 10.3.2 Interval Timer Operation
Figure 10.5 illustrates interval timer operation. To use the WDT as an interval timer, clear bit WT/IT to 0 and set bit TME to 1 in TCSR. An interval timer interrupt request is generated at each TCNT overflow. This function can be used to generate interval timer interrupts at regular intervals.
H'FF
TCNT count value Time t H'00 WT/ IT = 0 TME = 1
Interval timer interrupt
Interval timer interrupt
Interval timer interrupt
Interval timer interrupt
Interval timer interrupt
Figure 10.5 Interval Timer Operation
Rev.2.00 Mar. 22, 2007 Page 326 of 684 REJ09B0352-0200
10. Watchdog Timer
10.3.3
Timing of Setting of Overflow Flag (OVF)
Figure 10.6 shows the timing of setting of the OVF flag in TCSR. The OVF flag is set to 1 when TCNT overflows. At the same time, a reset signal is generated in watchdog timer operation, or an interval timer interrupt is generated in interval timer operation.
H'FF
H'00
TCNT
Overflow signal
OVF
Figure 10.6 Timing of Setting of OVF
Rev.2.00 Mar. 22, 2007 Page 327 of 684 REJ09B0352-0200
10. Watchdog Timer
10.3.4
Timing of Setting of Watchdog Timer Reset Bit (WRST)
The WRST bit in RSTCSR is valid when bits WT/IT and TME are both set to 1 in TCSR. Figure 10.7 shows the timing of setting of WRST and the internal reset timing. The WRST bit is set to 1 when TCNT overflows and OVF is set to 1. At the same time an internal reset signal is generated for the entire H8/3022 Group chip. This internal reset signal clears OVF to 0, but the WRST bit remains set to 1. The reset routine must therefore clear the WRST bit.
TCNT
H'FF
H'00
Overflow signal
OVF
WDT internal reset
WRST
Figure 10.7 Timing of Setting of WRST Bit and Internal Reset
Rev.2.00 Mar. 22, 2007 Page 328 of 684 REJ09B0352-0200
10. Watchdog Timer
10.4
Interrupts
During interval timer operation, an overflow generates an interval timer interrupt (WOVI). The interval timer interrupt is requested whenever the OVF bit is set to 1 in TCSR.
10.5
Usage Notes
Contention between TCNT Write and Increment: If a timer counter clock pulse is generated during the T3 state of a write cycle to TCNT, the write takes priority and the timer count is not incremented. See figure 10.8.
Write cycle: CPU writes to TCNT T1 T2 T3
TCNT
Internal write signal
TCNT input clock
TCNT
N
M Counter write data
Figure 10.8 Contention between TCNT Write and Increment Changing CKS2 to CKS0 Values: Halt TCNT by clearing the TME bit to 0 in TCSR before changing the values of bits CKS2 to CKS0.
Rev.2.00 Mar. 22, 2007 Page 329 of 684 REJ09B0352-0200
10. Watchdog Timer
Rev.2.00 Mar. 22, 2007 Page 330 of 684 REJ09B0352-0200
11. Serial Communication Interface
Section 11 Serial Communication Interface
11.1 Overview
The H8/3022 Group has a serial communication interface (SCI) with two independent channels. The two channels are functionally identical. The SCI can communicate in asynchronous or synchronous mode. It also has a multiprocessor communication function for serial communication among two or more processors. When the SCI is not used, it can be halted to conserve power. Each SCI channel can be halted independently. For details see section 17.6, Module Standby Function. Channel 0 (SCI0) also has a smart card interface function conforming to the ISO/IEC7816-3 (Identification Card) standard. This function supports serial communication with a smart card. For details, see section 12, Smart Card Interface. 11.1.1 Features
SCI features are listed below. * Selection of asynchronous or synchronous mode for serial communication a. Asynchronous mode Serial data communication is synchronized one character at a time. The SCI can communicate with a universal asynchronous receiver/transmitter (UART), asynchronous communication interface adapter (ACIA), or other chip that employs standard asynchronous serial communication. It can also communicate with two or more other processors using the multiprocessor communication function. There are twelve selectable serial data communication formats. Data length: 7 or 8 bits 1 or 2 bits even, odd, or none 1 or 0 parity, overrun, and framing errors by reading the RxD level directly when a framing error occurs Stop bit length: Parity bit: Multiprocessor bit: Receive error detection: Break detection: b. Synchronous mode Serial data communication is synchronized with a clock signal. The SCI can communicate with other chips having a synchronous communication function. There is one serial data communication format.
Rev.2.00 Mar. 22, 2007 Page 331 of 684 REJ09B0352-0200
11. Serial Communication Interface

Data length: Receive error detection:
8 bits overrun errors
* Full-duplex communication The transmitting and receiving sections are independent, so the SCI can transmit and receive simultaneously. The transmitting and receiving sections are both double-buffered, so serial data can be transmitted and received continuously. * Built-in baud rate generator with selectable bit rates * Selectable transmit/receive clock sources: internal clock from baud rate generator, or external clock from the SCK pin. * Four types of interrupts Transmit-data-empty, transmit-end, receive-data-full, and receive-error interrupts are requested independently.
Rev.2.00 Mar. 22, 2007 Page 332 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.1.2
Block Diagram
Figure 11.1 shows a block diagram of the SCI.
Bus interface
Internal data bus
Module data bus
RDR RxD RSR
TDR TSR
SSR SCR SMR Transmit/ receive control
BRR Baud rate generator Clock External clock TEI TXI RXI ERI /4 /16 /64
TxD
Parity generation Parity check
SCK
Legend RSR: Receive shift register RDR: Receive data register TSR: Transmit shift register TDR: Transmit data register SMR: Serial mode register SCR: Serial control register SSR: Serial status register BRR: Bit rate register
Figure 11.1 SCI Block Diagram
Rev.2.00 Mar. 22, 2007 Page 333 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.1.3
Pin Configuration
The SCI has the serial pins for each channel as listed in table 11.1. Table 11.1 SCI Pins
Channel 0 Name Serial clock pin Receive data pin Transmit data pin 1 Serial clock pin Receive data pin Transmit data pin Abbreviation SCK0 RxD0 TxD0 SCK1 RxD1 TxD1 I/O Input/output Input Output Input/output Input Output Function SCI0 clock input/output SCI0 receive data input SCI0 transmit data output SCI1 clock input/output SCI1 receive data input SCI1 transmit data output
Rev.2.00 Mar. 22, 2007 Page 334 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.1.4
Register Configuration
The SCI has the internal registers as listed in table 11.2. These registers select asynchronous or synchronous mode, specify the data format and bit rate, and control the transmitter and receiver sections. Table 11.2 Registers
Channel 0 Address* H'FFB0 H'FFB1 H'FFB2 H'FFB3 H'FFB4 H'FFB5 1 H'FFB8 H'FFB9 H'FFBA H'FFBB H'FFBC H'FFBD
1
Name Serial mode register Bit rate register Serial control register Transmit data register Serial status register Receive data register Serial mode register Bit rate register Serial control register Transmit data register Serial status register Receive data register
Abbreviation SMR BRR SCR TDR SSR RDR SMR BRR SCR TDR SSR RDR
R/W R/W R/W R/W R/W R/(W)* R R/W R/W R/W R/W R/(W)* R
2 2
Initial Value H'00 H'FF H'00 H'FF H'84 H'00 H'00 H'FF H'00 H'FF H'84 H'00
Notes: 1. Lower 16 bits of the address. 2. Only 0 can be written to clear flags.
Rev.2.00 Mar. 22, 2007 Page 335 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.2
11.2.1
Register Descriptions
Receive Shift Register (RSR)
RSR is an 8-bit register that receives serial data.
Bit 7 6 5 4 3 2 1 0
Read/Write
--
--
--
--
--
--
--
--
The SCI loads serial data input at the RxD pin into RSR in the order received, LSB (bit 0) first, thereby converting the data to parallel data. When 1 byte has been received, it is automatically transferred to RDR. The CPU cannot read or write RSR directly. 11.2.2 Receive Data Register (RDR)
RDR is an 8-bit register that stores received serial data.
Bit Initial value Read/Write 7 0 R 6 0 R 5 0 R 4 0 R 3 0 R 2 0 R 1 0 R 0 0 R
When the SCI finishes receiving 1 byte of serial data, it transfers the received data from RSR into RDR for storage. RSR is then ready to receive the next data. This double buffering allows data to be received continuously. RDR is a read-only register. Its contents cannot be modified by the CPU. RDR is initialized to H'00 by a reset and in standby mode.
Rev.2.00 Mar. 22, 2007 Page 336 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.2.3
Transmit Shift Register (TSR)
TSR is an 8-bit register used to transmit serial data.
Bit 7 6 5 4 3 2 1 0
Read/Write
--
--
--
--
--
--
--
--
The SCI loads transmit data from TDR into TSR, then transmits the data serially from the TxD pin, LSB (bit 0) first. After transmitting one data byte, the SCI automatically loads the next transmit data from TDR into TSR and starts transmitting it. If the TDRE flag is set to 1 in SSR, however, the SCI does not load the TDR contents into TSR. The CPU cannot read or write TSR directly. 11.2.4 Transmit Data Register (TDR)
TDR is an 8-bit register that stores data for serial transmission.
Bit Initial value Read/Write 7 1 R/W 6 1 R/W 5 1 R/W 4 1 R/W 3 1 R/W 2 1 R/W 1 1 R/W 0 1 R/W
When the SCI detects that TSR is empty, it moves transmit data written in TDR from TDR into TSR and starts serial transmission. Continuous serial transmission is possible by writing the next transmit data in TDR during serial transmission from TSR. The CPU can always read and write TDR. TDR is initialized to H'FF by a reset and in standby mode.
Rev.2.00 Mar. 22, 2007 Page 337 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.2.5
Serial Mode Register (SMR)
SMR is an 8-bit register that specifies the SCI serial communication format and selects the clock source for the baud rate generator.
Bit Initial value Read/Write 7 C/A 0 R/W 6 CHR 0 R/W 5 PE 0 R/W 4 O/E 0 R/W 3 STOP 0 R/W 2 MP 0 R/W 1 CKS1 0 R/W 0 CKS0 0 R/W
Clock select 1/0 These bits select the baud rate generator's clock source Multiprocessor mode Selects the multiprocessor function Stop bit length Selects the stop bit length Parity mode Selects even or odd parity Parity enable Selects whether a parity bit is added Character length Selects character length in asynchronous mode Communication mode Selects asynchronous or synchronous mode
The CPU can always read and write SMR. SMR is initialized to H'00 by a reset and in standby mode.
Rev.2.00 Mar. 22, 2007 Page 338 of 684 REJ09B0352-0200
11. Serial Communication Interface
Bit 7--Communication Mode (C/A): Selects whether the SCI operates in asynchronous or synchronous mode.
Bit 7 C/A 0 1 Description Asynchronous mode Synchronous mode (Initial value)
Bit 6--Character Length (CHR): Selects 7-bit or 8-bit data length in asynchronous mode. In synchronous mode the data length is 8 bits regardless of the CHR setting.
Bit 6 CHR 0 1 Note: * Description 8-bit data 7-bit data* When 7-bit data is selected, the MSB (bit 7) in TDR is not transmitted. (Initial value)
Bit 5--Parity Enable (PE): In asynchronous mode, this bit enables or disables the addition of a parity bit to transmit data, and the checking of the parity bit in receive data. In synchronous mode the parity bit is neither added nor checked, regardless of the PE setting.
Bit 5 PE 0 1 Note: * Description Parity bit not added or checked Parity bit added and checked* When PE is set to 1, an even or odd parity bit is added to transmit data according to the even or odd parity mode selected by the O/E bit, and the parity bit in receive data is checked to see that it matches the even or odd mode selected by the O/E bit. (Initial value)
Rev.2.00 Mar. 22, 2007 Page 339 of 684 REJ09B0352-0200
11. Serial Communication Interface
Bit 4--Parity Mode (O/E): Selects even or odd parity. The O/E bit setting is valid in asynchronous mode when the PE bit is set to 1 to enable the adding and checking of a parity bit. The O/E setting is ignored in synchronous mode, or when parity adding and checking is disabled in asynchronous mode.
Bit 4 O/E 0 1 Description Even parity* Odd parity*
2 1
(Initial value)
Notes: 1. When even parity is selected, the parity bit added to transmit data makes an even number of 1s in the transmitted character and parity bit combined. Receive data must have an even number of 1s in the received character and parity bit combined. 2. When odd parity is selected, the parity bit added to transmit data makes an odd number of 1s in the transmitted character and parity bit combined. Receive data must have an odd number of 1s in the received character and parity bit combined.
Bit 3--Stop Bit Length (STOP): Selects one or two stop bits in asynchronous mode. This setting is used only in asynchronous mode. In synchronous mode no stop bit is added, so the STOP bit setting is ignored.
Bit 3 STOP 0 1 Description One stop bit*
1 2
(Initial value)
Two stop bits*
Notes: 1. One stop bit (with value 1) is added at the end of each transmitted character. 2. Two stop bits (with value 1) are added at the end of each transmitted character.
In receiving, only the first stop bit is checked, regardless of the STOP bit setting. If the second stop bit is 1 it is treated as a stop bit. If the second stop bit is 0 it is treated as the start bit of the next incoming character.
Rev.2.00 Mar. 22, 2007 Page 340 of 684 REJ09B0352-0200
11. Serial Communication Interface
Bit 2--Multiprocessor Mode (MP): Selects a multiprocessor format. When a multiprocessor format is selected, parity settings made by the PE and O/E bits are ignored. The MP bit setting is valid only in asynchronous mode. It is ignored in synchronous mode. For further information on the multiprocessor communication function, see section 11.3.3, Multiprocessor Communication Function.
Bit 2 MP 0 1 Description Multiprocessor function disabled Multiprocessor format selected (Initial value)
Bits 1 and 0--Clock Select 1 and 0 (CKS1/0): These bits select the clock source of the on-chip baud rate generator. Four clock sources are available: , /4, /16, and /64. For the relationship between the clock source, bit rate register setting, and baud rate, see section 11.2.8, Bit Rate Register.
Bit 1 CKS1 0 Bit 0 CKS0 0 1 1 0 1 Description clock selected /4 clock selected /16 clock selected /64 clock selected (Initial value)
Rev.2.00 Mar. 22, 2007 Page 341 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.2.6
Serial Control Register (SCR)
SCR enables the SCI transmitter and receiver, enables or disables serial clock output in asynchronous mode, enables or disables interrupts, and selects the transmit/receive clock source.
Bit Initial value Read/Write 7 TIE 0 R/W 6 RIE 0 R/W 5 TE 0 R/W 4 RE 0 R/W 3 MPIE 0 R/W 2 TEIE 0 R/W 1 CKE1 0 R/W 0 CKE0 0 R/W
Clock enable 1/0 These bits select the SCI clock source Transmit end interrupt enable Enables or disables transmitend interrupts (TEI) Multiprocessor interrupt enable Enables or disables multiprocessor interrupts Receive enable Enables or disables the receiver Transmit enable Enables or disables the transmitter Receive interrupt enable Enables or disables receive-data-full interrupts (RXI) and receive-error interrupts (ERI) Transmit interrupt enable Enables or disables transmit-data-empty interrupts (TXI)
The CPU can always read and write SCR. SCR is initialized to H'00 by a reset and in standby mode.
Rev.2.00 Mar. 22, 2007 Page 342 of 684 REJ09B0352-0200
11. Serial Communication Interface
Bit 7--Transmit Interrupt Enable (TIE): Enables or disables the transmit-data-empty interrupt (TXI) requested when the TDRE flag in SSR is set to 1 due to transfer of serial transmit data from TDR to TSR.
Bit 7 TIE 0 1 Note: * Description Transmit-data-empty interrupt request (TXI) is disabled* Transmit-data-empty interrupt request (TXI) is enabled TXI interrupt requests can be cleared by reading the value 1 from the TDRE flag, then clearing it to 0; or by clearing the TIE bit to 0. (Initial value)
Bit 6--Receive Interrupt Enable (RIE): Enables or disables the receive-data-full interrupt (RXI) requested when the RDRF flag is set to 1 in SSR due to transfer of serial receive data from RSR to RDR; also enables or disables the receive-error interrupt (ERI).
Bit 6 RIE 0 1 Note: * Description Receive-end (RXI) and receive-error (ERI) interrupt requests are disabled* Receive-end (RXI) and receive-error (ERI) interrupt requests are enabled RXI and ERI interrupt requests can be cleared by reading the value 1 from the RDRF, FER, PER, or ORER flag, then clearing it to 0; or by clearing the RIE bit to 0. (Initial value)
Bit 5--Transmit Enable (TE): Enables or disables the start of SCI serial transmitting operations.
Bit 5 TE 0 1 Description Transmitting disabled* Transmitting enabled*
1
(Initial value)
2
Notes: 1. The TDRE flag is fixed at 1 in SSR. 2. In the enabled state, serial transmitting starts when the TDRE flag in SSR is cleared to 0 after writing of transmit data into TDR. Select the transmit format in SMR before setting the TE bit to 1.
Rev.2.00 Mar. 22, 2007 Page 343 of 684 REJ09B0352-0200
11. Serial Communication Interface
Bit 4--Receive Enable (RE): Enables or disables the start of SCI serial receiving operations.
Bit 4 RE 0 1 Description Receiving disabled* Receiving enabled*
1
(Initial value)
2
Notes: 1. Clearing the RE bit to 0 does not affect the RDRF, FER, PER, and ORER flags. These flags retain their previous values. 2. In the enabled state, serial receiving starts when a start bit is detected in asynchronous mode, or serial clock input is detected in synchronous mode. Select the receive format in SMR before setting the RE bit to 1.
Bit 3--Multiprocessor Interrupt Enable (MPIE): Enables or disables multiprocessor interrupts. The MPIE setting is valid only in asynchronous mode, and only if the MP bit is set to 1 in SMR. The MPIE setting is ignored in synchronous mode or when the MP bit is cleared to 0.
Bit 3 MPIE 0 Description Multiprocessor interrupts are disabled (normal receive operation) [Clearing conditions] The MPIE bit is cleared to 0. MPB = 1 in received data. (Initial value)
1
Multiprocessor interrupts are enabled* Receive-data-full interrupts (RXI), receive-error interrupts (ERI), and setting of the RDRF, FER, and ORER status flags in SSR are disabled until data with the multiprocessor bit set to 1 is received. * The SCI does not transfer receive data from RSR to RDR, does not detect receive errors, and does not set the RDRF, FER, and ORER flags in SSR. When it receives data in which MPB = 1, the SCI sets the MPB bit to 1 in SSR, automatically clears the MPIE bit to 0, and enables RXI and ERI interrupts (if the RIE bit is set to 1 in SCR) and setting of the FER and ORER flags.
Note:
Rev.2.00 Mar. 22, 2007 Page 344 of 684 REJ09B0352-0200
11. Serial Communication Interface
Bit 2--Transmit-End Interrupt Enable (TEIE): Enables or disables the transmit-end interrupt (TEI) requested if TDR does not contain new transmit data when the MSB is transmitted.
Bit 2 TEIE 0 1 Note: * Description Transmit-end interrupt requests (TEI) are disabled* Transmit-end interrupt requests (TEI) are enabled* TEI interrupt requests can be cleared by reading the value 1 from the TDRE flag in SSR, then clearing the TDRE flag to 0, thereby also clearing the TEND flag to 0; or by clearing the TEIE bit to 0. (Initial value)
Bits 1 and 0--Clock Enable 1 and 0 (CKE1/0): These bits select the SCI clock source and enable or disable clock output from the SCK pin. Depending on the settings of CKE1 and CKE0, the SCK pin can be used for generic input/output, serial clock output, or serial clock input. The CKE0 setting is valid only in asynchronous mode, and only when the SCI is internally clocked (CKE1 = 0). The CKE0 setting is ignored in synchronous mode, or when an external clock source is selected (CKE1 = 1). After setting the CKE1 and CKE0 bits, select the SCI operating mode in SMR. For further details on selection of the SCI clock source, see table 11.9 in section 11.3, Operation.
Bit 1 CKE1 0 Bit 0 CKE0 0 Description Asynchronous mode Synchronous mode 1 Asynchronous mode Synchronous mode 1 0 Asynchronous mode Synchronous mode 1 Asynchronous mode Synchronous mode Internal clock, SCK pin available for generic 1 input/output* Internal clock, SCK pin used for serial clock output* Internal clock, SCK pin used for clock output*
2 1
Internal clock, SCK pin used for serial clock output External clock, SCK pin used for clock input*
3
External clock, SCK pin used for serial clock input External clock, SCK pin used for clock input*
3
External clock, SCK pin used for serial clock input
Notes: 1. Initial value 2. The output clock frequency is the same as the bit rate. 3. The input clock frequency is 16 times the bit rate.
Rev.2.00 Mar. 22, 2007 Page 345 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.2.7
Serial Status Register (SSR)
SSR is an 8-bit register containing multiprocessor bit values, and status flags that indicate the SCI operating status.
Bit Initial value Read/Write 7 TDRE 1 R/(W)* 6 RDRF 0 R/(W)* 5 ORER 0 R/(W)* 4 FER 0 R/(W)* 3 PER 0 R/(W)* 2 TEND 1 R 1 MPB 0 R 0 MPBT 0 R/W Multiprocessor bit transfer Value of multiprocessor bit to be transmitted Multiprocessor bit Stores the received multiprocessor bit value Transmit end Status flag indicating end of transmission Parity error Status flag indicating detection of a receive parity error Framing error Status flag indicating detection of a receive framing error Overrun error Status flag indicating detection of a receive overrun error Receive data register full Status flag indicating that data has been received and stored in RDR Transmit data register empty Status flag indicating that transmit data has been transferred from TDR into TSR and new data can be written in TDR Note: * Only 0 can be written to clear the flag.
Rev.2.00 Mar. 22, 2007 Page 346 of 684 REJ09B0352-0200
11. Serial Communication Interface
The CPU can always read and write SSR, but cannot write 1 in the TDRE, RDRF, ORER, PER, and FER flags. These flags can be cleared to 0 only if they have first been read while set to 1. The TEND and MPB flags are read-only bits that cannot be written. SSR is initialized to H'84 by a reset and in standby mode. Bit 7--Transmit Data Register Empty (TDRE): Indicates that the SCI has loaded transmit data from TDR into TSR and the next serial transmit data can be written in TDR.
Bit 7 TDRE 0 Description TDR contains valid transmit data [Clearing conditions] Software reads TDRE while it is set to 1, then writes 0. TDR does not contain valid transmit data (Initial value) [Setting conditions] The chip is reset or enters standby mode. The TE bit in SCR is cleared to 0. TDR contents are loaded into TSR, so new data can be written in TDR.
1
Bit 6--Receive Data Register Full (RDRF): Indicates that RDR contains new receive data.
Bit 6 RDRF 0 Description RDR does not contain new receive data [Clearing conditions] The chip is reset or enters standby mode. Software reads RDRF while it is set to 1, then writes 0. RDR contains new receive data [Setting condition] When serial data is received normally and transferred from RSR to RDR. (Initial value)
1
Note: The RDR contents and RDRF flag are not affected by detection of receive errors or by clearing of the RE bit to 0 in SCR. They retain their previous values. If the RDRF flag is still set to 1 when reception of the next data ends, an overrun error occurs and receive data is lost.
Rev.2.00 Mar. 22, 2007 Page 347 of 684 REJ09B0352-0200
11. Serial Communication Interface
Bit 5--Overrun Error (ORER): Indicates that data reception ended abnormally due to an overrun error.
Bit 5 ORER 0 Description Receiving is in progress or has ended normally [Clearing conditions] The chip is reset or enters standby mode. Software reads ORER while it is set to 1, then writes 0. A receive overrun error occurred* [Setting condition] Reception of the next serial data ends when RDRF = 1.
2
(Initial value)*
1
1
Notes: 1. Clearing the RE bit to 0 in SCR does not affect the ORER flag, which retains its previous value. 2. RDR continues to hold the receive data before the overrun error, so subsequent receive data is lost. Serial receiving cannot continue while the ORER flag is set to 1. In synchronous mode, serial transmitting is also disabled.
Bit 4--Framing Error (FER): Indicates that data reception ended abnormally due to a framing error in asynchronous mode.
Bit 4 FER 0 Description Receiving is in progress or has ended normally [Clearing conditions] The chip is reset or enters standby mode. Software reads FER while it is set to 1, then writes 0. A receive framing error occurred [Setting condition] 2 The stop bit at the end of receive data is checked and found to be 0.* (Initial value)*
1
1
Notes: 1. Clearing the RE bit to 0 in SCR does not affect the FER flag, which retains its previous value. 2. When the stop bit length is 2 bits, only the first bit is checked. The second stop bit is not checked. When a framing error occurs the SCI transfers the receive data into RDR but does not set the RDRF flag. Serial receiving cannot continue while the FER flag is set to 1. In synchronous mode, serial transmitting is also disabled.
Rev.2.00 Mar. 22, 2007 Page 348 of 684 REJ09B0352-0200
11. Serial Communication Interface
Bit 3--Parity Error (PER): Indicates that data reception ended abnormally due to a parity error in asynchronous mode.
Bit 3 PER 0 Description Receiving is in progress or has ended normally* [Clearing conditions] The chip is reset or enters standby mode. Software reads PER while it is set to 1, then writes 0. A receive parity error occurred* [Setting condition] The number of 1s in receive data, including the parity bit, does not match the even or odd parity setting of O/E in SMR.
2 1
(Initial value)
1
Notes: 1. Clearing the RE bit to 0 in SCR does not affect the PER flag, which retains its previous value. 2. When a parity error occurs the SCI transfers the receive data into RDR but does not set the RDRF flag. Serial receiving cannot continue while the PER flag is set to 1. In synchronous mode, serial transmitting is also disabled.
Bit 2--Transmit End (TEND): Indicates that when the last bit of a serial character was transmitted TDR did not contain new transmit data, so transmission has ended. The TEND flag is a read-only bit and cannot be written.
Bit 2 TEND 0 Description Transmission is in progress [Clearing conditions] Software reads TDRE while it is set to 1, then writes 0 in the TDRE flag. End of transmission [Setting conditions] The chip is reset or enters standby mode. The TE bit is cleared to 0 in SCR. TDRE is 1 when the last bit of a serial character is transmitted. (Initial value)
1
Rev.2.00 Mar. 22, 2007 Page 349 of 684 REJ09B0352-0200
11. Serial Communication Interface
Bit 1--Multiprocessor Bit (MPB): Stores the value of the multiprocessor bit in receive data when a multiprocessor format is used in asynchronous mode. MPB is a read-only bit and cannot be written.
Bit 1 MPB 0 1 Note: * Description Multiprocessor bit value in receive data is 0* Multiprocessor bit value in receive data is 1 If the RE bit is cleared to 0 when a multiprocessor format is selected, MPB retains its previous value. (Initial value)
Bit 0--Multiprocessor Bit Transfer (MPBT): Stores the value of the multiprocessor bit added to transmit data when a multiprocessor format is selected for transmitting in asynchronous mode. The MPBT setting is ignored in synchronous mode, when a multiprocessor format is not selected, or when the SCI is not transmitting.
Bit 0 MPBT 0 1 Description Multiprocessor bit value in transmit data is 0 Multiprocessor bit value in transmit data is 1 (Initial value)
11.2.8
Bit Rate Register (BRR)
BRR is an 8-bit register that, together with the CKS1 and CKS0 bits in SMR that select the baud rate generator clock source, determines the serial communication bit rate.
Bit Initial value Read/Write 7 1 R/W 6 1 R/W 5 1 R/W 4 1 R/W 3 1 R/W 2 1 R/W 1 1 R/W 0 1 R/W
The CPU can always read and write BRR. BRR is initialized to H'FF by a reset and in standby mode. The baud rate generator is controlled separately for the individual channels, so different values may be set for each. Table 11.3 shows examples of BRR settings in asynchronous mode. Table 11.4 shows examples of BRR settings in synchronous mode.
Rev.2.00 Mar. 22, 2007 Page 350 of 684 REJ09B0352-0200
11. Serial Communication Interface
Table 11.3 Examples of Bit Rates and BRR Settings in Asynchronous Mode
(MHz) 2 Bit Rate (bits/s) 110 150 300 600 1200 2400 4800 9600 19200 31250 38400 n 1 1 0 0 0 0 0 0 0 0 0 N 141 103 207 103 51 25 12 6 2 1 1 Error (%) 0.03 0.16 0.16 0.16 0.16 0.16 0.16 -6.99 8.51 0.00 -18.62 n 1 1 0 0 0 0 0 0 0 0 0 2.097152 N 148 108 217 108 54 26 13 6 2 1 1 Error (%) -0.04 0.21 0.21 0.21 -0.70 1.14 -2.48 -2.48 13.78 4.86 -14.67 n 1 1 0 0 0 0 0 0 0 0 0 2.4576 N 174 127 255 127 63 31 15 7 3 1 1 Error (%) -0.26 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 22.88 0.00 n 1 1 1 0 0 0 0 0 0 0 N 212 155 77 155 77 38 19 9 4 2 3 Error (%) 0.03 0.16 0.16 0.16 0.16 0.16 -2.34 -2.34 -2.34 0.00 --
----
(MHz) 3.6864 Bit Rate (bits/s) 110 150 300 600 1200 2400 4800 9600 19200 31250 38400 n 2 1 1 0 0 0 0 0 0 N 64 191 95 191 95 47 23 11 5 Error (%) 0.70 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 -- 0.00 n 2 1 1 0 0 0 0 0 0 0 0 N 70 207 103 207 103 51 25 12 6 3 2 4 Error (%) 0.03 0.16 0.16 0.16 0.16 0.16 0.16 0.16 -6.99 0.00 8.51 n 2 1 1 0 0 0 0 0 0 0 0 4.9152 N 86 255 127 255 127 63 31 15 7 4 3 Error (%) 0.31 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 -1.70 0.00 n 2 2 1 1 0 0 0 0 0 0 0 N 88 64 129 64 129 64 32 15 7 4 3 5 Error (%) -0.25 0.16 0.16 0.16 0.16 0.16 -1.36 1.73 1.73 0.00 1.73
---- 0 2
Rev.2.00 Mar. 22, 2007 Page 351 of 684 REJ09B0352-0200
11. Serial Communication Interface (MHz) 6 Bit Rate (bits/s) 110 150 300 600 1200 2400 4800 9600 19200 31250 38400 n 2 2 1 1 0 0 0 0 0 0 0 N 106 77 155 77 155 77 38 19 9 5 4 Error (%) -0.44 0.16 0.16 0.16 0.16 0.16 0.16 -2.34 -2.34 0.00 -2.34 n 2 2 1 1 0 0 0 0 0 0 0 N 108 79 159 79 159 79 39 19 9 5 4 6.144 Error (%) 0.08 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 2.40 0.00 n 2 2 1 1 0 0 0 0 0 0 0 7.3728 N 130 95 191 95 191 95 47 23 11 6 5 Error (%) -0.07 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 5.33 0.00 n 2 2 1 1 0 0 0 0 0 0 0 N 141 103 207 103 207 103 51 25 12 7 6 8 Error (%) 0.03 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.00 -6.99
(MHz) 9.8304 Bit Rate (bits/s) 110 150 300 600 1200 2400 4800 9600 19200 31250 38400 n 2 2 1 1 0 0 0 0 0 0 0 N 174 127 255 127 255 127 63 31 15 9 7 Error (%) -0.26 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 -1.70 0.00 n 2 2 2 1 1 0 0 0 0 0 0 N 177 129 64 129 64 129 64 32 15 9 7 10 Error (%) -0.25 0.16 0.16 0.16 0.16 0.16 0.16 -1.36 1.73 0.00 1.73 n 2 2 2 1 1 0 0 0 0 0 0 N 212 155 77 155 77 155 77 38 19 11 9 12 Error (%) 0.03 0.16 0.16 0.16 0.16 0.16 0.16 0.16 -2.34 0.00 -2.34 n 2 2 2 1 1 0 0 0 0 0 0 N 217 159 79 159 79 159 79 39 19 11 9 12.288 Error (%) 0.08 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 2.40 0.00
Rev.2.00 Mar. 22, 2007 Page 352 of 684 REJ09B0352-0200
11. Serial Communication Interface (MHz) 14 Bit Rate (bits/s) 110 150 300 600 1200 2400 4800 9600 19200 31250 38400 n 2 2 2 1 1 0 0 0 0 0 0 N 248 181 90 181 90 181 90 45 22 11 10 Error (%) -0.17 0.16 0.16 0.16 0.16 0.16 0.16 -0.93 -0.93 0.00 3.57 n 3 2 2 1 1 0 0 0 0 0 0 14.7456 N 64 191 95 191 95 191 95 47 23 14 11 Error (%) 0.70 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 -1.70 0.00 n 3 2 2 1 1 0 0 0 0 0 0 N 70 207 103 207 103 207 103 51 25 15 12 16 Error (%) 0.03 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.16 0.00 0.16 n 3 2 2 1 1 0 0 0 0 0 0 N 79 233 116 233 116 233 116 58 28 17 14 18 Error (%) -0.12 0.16 0.16 0.16 0.16 0.16 0.16 -0.69 1.02 0.00 -2.34
Rev.2.00 Mar. 22, 2007 Page 353 of 684 REJ09B0352-0200
11. Serial Communication Interface
Table 11.4 Examples of Bit Rates and BRR Settings in Synchronous Mode
(MHz) Bit Rate (bits/s) 110 250 500 1k 2.5 k 5k 10 k 25 k 50 k 100 k 250 k 500 k 1M 2M 2.5 M 4M Legend Blank: No setting available --: Setting possible, but error occurs *: Continuous transmission/reception not possible The BRR setting is calculated as follows: Asynchronous mode: 6 N= x 10 - 1 2n-1 64 x 2 x B Synchronous mode: N= 2n-1 8x2 xB B: N: : n: n 3 2 1 1 0 0 0 0 0 0 0 0 2 N 70 124 249 124 199 99 49 19 9 4 1 0* n -- 2 2 1 1 0 0 0 0 0 0 0 0 4 N -- 249 124 249 99 199 99 39 19 9 3 1 0* n -- 3 2 2 1 1 0 0 0 0 0 0 0 0 -- 8 N -- 124 249 124 199 99 199 79 39 19 7 3 1 0* -- n -- -- -- -- 1 1 0 0 0 0 0 0 -- -- 0 10 N -- -- -- -- 249 124 249 99 49 24 9 4 -- -- 0* n -- 3 3 2 2 1 1 0 0 0 0 0 0 0 -- 0 16 N -- 249 124 249 99 199 99 159 79 39 15 7 3 1 -- 0* n -- -- 3 3 2 1 1 0 0 0 0 0 0 -- -- -- 18 N -- -- 140 69 112 224 112 179 89 44 17 8 4 -- -- --
x 10 - 1
6
Bit rate (bits/s) BRR setting for baud rate generator (0 N 255) System clock frequency (MHz) Baud rate generator clock source (n = 0, 1, 2, 3)
Rev.2.00 Mar. 22, 2007 Page 354 of 684 REJ09B0352-0200
11. Serial Communication Interface (For the clock sources and values of n, see the following table.) Settings with an error of 1% or less are recommended. SMR Settings n 0 1 2 3 Clock Source /4 /16 /64 CKS1 0 0 1 1 CKS0 0 1 0 1
Note:
The bit rate error in asynchronous mode is calculated as follows. 6 x 10 -1} x 100 Error (%) ={ 2n-1 (N + 1) x B x 64 x 2
Rev.2.00 Mar. 22, 2007 Page 355 of 684 REJ09B0352-0200
11. Serial Communication Interface
Table 11.5 indicates the maximum bit rates in asynchronous mode for various system clock frequencies. Tables 11.6 and 11.7 indicate the maximum bit rates with external clock input. Table 11.5 Maximum Bit Rates for Various Frequencies (Asynchronous Mode)
Settings (MHz) 2 2.097152 2.4576 3 3.6864 4 4.9152 5 6 6.144 7.3728 8 9.8304 10 12 12.288 14 14.7456 16 17.2032 18 Maximum Bit Rate (bits/s) 62500 65536 76800 93750 115200 125000 153600 156250 187500 192000 230400 250000 307200 312500 375000 384000 437500 460800 500000 537600 562500 n 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 N 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Rev.2.00 Mar. 22, 2007 Page 356 of 684 REJ09B0352-0200
11. Serial Communication Interface
Table 11.6 Maximum Bit Rates with External Clock Input (Asynchronous Mode)
(MHz) 2 2.097152 2.4576 3 3.6864 4 4.9152 5 6 6.144 7.3728 8 9.8304 10 12 12.288 14 14.7456 16 17.2032 18 External Input Clock (MHz) 0.5000 0.5243 0.6144 0.7500 0.9216 1.0000 1.2288 1.2500 1.5000 1.5360 1.8432 2.0000 2.4576 2.5000 3.0000 3.0720 3.5000 3.6864 4.0000 4.3008 4.5000 Maximum Bit Rate (bits/s) 31250 32768 38400 46875 57600 62500 76800 78125 93750 96000 115200 125000 153600 156250 187500 192000 218750 230400 250000 268800 281250
Rev.2.00 Mar. 22, 2007 Page 357 of 684 REJ09B0352-0200
11. Serial Communication Interface
Table 11.7 Maximum Bit Rates with External Clock Input (Synchronous Mode)
(MHz) 2 4 6 8 10 12 14 16 18 External Input Clock (MHz) 0.3333 0.6667 1.0000 1.3333 1.6667 2.0000 2.3333 2.6667 3.0000 Maximum Bit Rate (bits/s) 333333.3 666666.7 1000000.0 1333333.3 1666666.7 2000000.0 2333333.3 2666666.7 3000000.0
Rev.2.00 Mar. 22, 2007 Page 358 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.3
11.3.1
Operation
Overview
The SCI has an asynchronous mode in which characters are synchronized individually, and a synchronous mode in which communication is synchronized with clock pulses. Serial communication is possible in either mode. Asynchronous or synchronous mode and the communication format are selected in SMR, as shown in table 11.8. The SCI clock source is selected by the C/A bit in SMR and the CKE1 and CKE0 bits in SCR, as shown in table 11.9. Asynchronous Mode * Data length is selectable: 7 or 8 bits. * Parity and multiprocessor bits are selectable, and so is the stop bit length (1 or 2 bits). These selections determine the communication format and character length. * In receiving, it is possible to detect framing errors, parity errors, overrun errors, and the break state. * An internal or external clock can be selected as the SCI clock source. When an internal clock is selected, the SCI operates using the on-chip baud rate generator, and can output a serial clock signal with a frequency matching the bit rate. When an external clock is selected, the external clock input must have a frequency 16 times the bit rate. (The on-chip baud rate generator is not used.) Synchronous Mode * The communication format has a fixed 8-bit data length. * In receiving, it is possible to detect overrun errors. * An internal or external clock can be selected as the SCI clock source. When an internal clock is selected, the SCI operates using the on-chip baud rate generator, and outputs a serial clock signal to external devices. When an external clock is selected, the SCI operates on the input serial clock. The on-chip baud rate generator is not used.
Rev.2.00 Mar. 22, 2007 Page 359 of 684 REJ09B0352-0200
11. Serial Communication Interface
Table 11.8 SMR Settings and Serial Communication Formats
SCI Communication Format SMR Settings Bit 7 C/A 0 0 0 0 0 0 0 0 0 0 0 0 1 Bit 6 CHR 0 0 0 0 1 1 1 1 0 0 1 1 -- Bit 2 MP 0 0 0 0 0 0 0 0 1 1 1 1 -- Bit 5 PE 0 0 1 1 0 0 1 1 -- -- -- -- -- Bit 3 STOP 0 1 0 1 0 1 0 1 0 1 0 1 -- Synchronous mode 8-bit data Absent Asynchronous 8-bit data Present mode (multiprocessor 7-bit data format) Absent 7-bit data Absent Mode Data Length Multiprocessor Parity Bit Bit Absent Stop Bit Length 1 bit 2 bits Present 1 bit 2 bits 1 bit 2 bits Present 1 bit 2 bits 1 bit 2 bits 1 bit 2 bits None
Asynchronous 8-bit data Absent mode
Rev.2.00 Mar. 22, 2007 Page 360 of 684 REJ09B0352-0200
11. Serial Communication Interface
Table 11.9 SMR and SCR Settings and SCI Clock Source Selection
SMR Bit 7 C/A 0 0 0 0 1 1 1 1 SCR Settings Bit 1 CKE1 0 0 1 1 0 0 1 1 Bit 0 CKE0 0 1 0 1 0 1 0 1 External Inputs the serial clock Synchronous mode Internal External SCI Communication Format Mode Asynchronous mode Clock Source Internal SCK Pin Function SCI does not use the SCK pin Outputs a clock with frequency matching the bit rate Inputs a clock with frequency 16 times the bit rate Outputs the serial clock
Rev.2.00 Mar. 22, 2007 Page 361 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.3.2
Operation in Asynchronous Mode
In asynchronous mode each transmitted or received character begins with a start bit and ends with a stop bit. Serial communication is synchronized one character at a time. The transmitting and receiving sections of the SCI are independent, so full-duplex communication is possible. The transmitter and receiver are both double buffered, so data can be written and read while transmitting and receiving are in progress, enabling continuous transmitting and receiving. Figure 11.2 shows the general format of asynchronous serial communication. In asynchronous serial communication the communication line is normally held in the mark (high) state. The SCI monitors the line and starts serial communication when the line goes to the space (low) state, indicating a start bit. One serial character consists of a start bit (low), data (LSB first), parity bit (high or low), and stop bit (high), in that order. When receiving in asynchronous mode, the SCI synchronizes at the falling edge of the start bit. The SCI samples each data bit on the eighth pulse of a clock with a frequency 16 times the bit rate. Receive data is latched at the center of each bit.
Idle (mark) state 1 0/1 Parity bit 1 Stop bit 1
1 Serial data 0 Start bit 1 bit
(LSB) D0 D1 D2 D3 D4 D5 D6
(MSB) D7
Transmit or receive data 7 bits or 8 bits One unit of data (character or frame)
1 bit or 1 bit or no bit 2 bits
Figure 11.2 Data Format in Asynchronous Communication (Example: 8-Bit Data with Parity and 2 Stop Bits)
Rev.2.00 Mar. 22, 2007 Page 362 of 684 REJ09B0352-0200
11. Serial Communication Interface
Communication Formats: Table 11.10 shows the 12 communication formats that can be selected in asynchronous mode. The format is selected by settings in SMR. Table 11.10 Serial Communication Formats (Asynchronous Mode)
SMR Settings CHR 0 0 0 0 1 1 1 1 0 0 1 1 PE 0 0 1 1 0 0 1 1 MP 0 0 0 0 0 0 0 0 1 1 1 1 STOP 0 1 0 1 0 1 0 1 0 1 0 1 1 S S S S S S S S S Serial Communication Format and Frame Length 2 3 4 5 6 7 8 9 10 STOP STOP STOP P P STOP STOP STOP P P STOP STOP STOP MPB STOP STOP STOP STOP 11 12
8-bit data 8-bit data 8-bit data 8-bit data 7-bit data 7-bit data 7-bit data 7-bit data 8 bit data
-- -- -- --
S S S
8 bit data 7-bit data 7-bit data
MPB STOP STOP MPB STOP MPB STOP STOP
Legend S: Start bit STOP: Stop bit P: Parity bit MPB: Multiprocessor bit
Rev.2.00 Mar. 22, 2007 Page 363 of 684 REJ09B0352-0200
11. Serial Communication Interface
Clock: An internal clock generated by the on-chip baud rate generator or an external clock input from the SCK pin can be selected as the SCI transmit/receive clock. The clock source is selected by the C/A bit in SMR and bits CKE1 and CKE0 in SCR. See table 11.9. When an external clock is input at the SCK pin, it must have a frequency equal to 16 times the desired bit rate. When the SCI operates on an internal clock, it can output a clock signal at the SCK pin. The frequency of this output clock is equal to the bit rate. The phase is aligned as in figure 11.3 so that the rising edge of the clock occurs at the center of each transmit data bit.
0
D0
D1
D2
D3
D4
D5
D6
D7
0/1
1
1
1 frame
Figure 11.3 Phase Relationship between Output Clock and Serial Data (Asynchronous Mode) Transmitting and Receiving Data SCI Initialization (Asynchronous Mode): Before transmitting or receiving, clear the TE and RE bits to 0 in SCR, then initialize the SCI as follows. When changing the communication mode or format, always clear the TE and RE bits to 0 before following the procedure given below. Clearing TE to 0 sets the TDRE flag to 1 and initializes TSR. Clearing RE to 0, however, does not initialize the RDRF, PER, FER, and ORER flags and RDR, which retain their previous contents. When an external clock is used, the clock should not be stopped during initialization or subsequent operation. SCI operation becomes unreliable if the clock is stopped. Figure 11.4 shows a sample flowchart for initializing the SCI.
Rev.2.00 Mar. 22, 2007 Page 364 of 684 REJ09B0352-0200
11. Serial Communication Interface
Start of initialization
Clear TE and RE bits to 0 in SCR
Set CKE1 and CKE0 bits in SCR (leaving TE and RE bits cleared to 0)
1
1. Select the clock source in SCR. Clear the RIE, TIE, TEIE, MPIE, TE, and RE bits to 0. If clock output is selected in asynchronous mode, clock output starts immediately after the setting is made in SCR. 2. Select the communication format in SMR. 3. Write the value corresponding to the bit rate in BRR. This step is not necessary when an external clock is used. 4. Wait for at least the interval required to transmit or receive 1 bit, then set the TE or RE bit to 1 in SCR. Set the RIE, TIE, TEIE, and MPIE bits as necessary. Setting the TE or RE bit enables the SCI to use the TxD or RxD pin.
Select communication format in SMR
2
Set value in BRR Wait
3
1 bit interval elapsed? Yes Set TE or RE bit to 1 in SCR Set RIE, TIE, TEIE, and MPIE bits as necessary
No
4
Transmitting or receiving
Figure 11.4 Sample Flowchart for SCI Initialization
Rev.2.00 Mar. 22, 2007 Page 365 of 684 REJ09B0352-0200
11. Serial Communication Interface
Transmitting Serial Data (Asynchronous Mode): Figure 11.5 shows a sample flowchart for transmitting serial data and indicates the procedure to follow.
Initialize Start transmitting 1 1. SCI initialization: the transmit data output function of the TxD pin is selected automatically. After the TE bit is set to 1, one frame of 1s is output, then transmission is possible. 2. SCI status check and transmit data write: read SSR, check that the TDRE flag is 1, then write transmit data in TDR and clear the TDRE flag to 0. 3. To continue transmitting serial data: after checking that the TDRE flag is 1, indicating that data can be written, write data in TDR, then clear the TDRE flag to 0. 4. To output a break signal at the end of serial transmission: set the DDR bit to 1 and clear the DR bit to 0 (DDR and DR are I/O port registers), then clear the TE bit to 0 in SCR.
Read TDRE flag in SSR
2
No TDRE = 1? Yes Write transmit data in TDR and clear TDRE flag to 0 in SSR
All data transmitted? Yes
No
3
Read TEND flag in SSR No
TEND = 1? Yes Output break signal? Yes Clear DR bit to 0, set DDR bit to 1 Clear TE bit to 0 in SCR
No
4
End
Figure 11.5 Sample Flowchart for Transmitting Serial Data
Rev.2.00 Mar. 22, 2007 Page 366 of 684 REJ09B0352-0200
11. Serial Communication Interface
In transmitting serial data, the SCI operates as follows. * The SCI monitors the TDRE flag in SSR. When the TDRE flag is cleared to 0 the SCI recognizes that TDR contains new data, and loads this data from TDR into TSR. * After loading the data from TDR into TSR, the SCI sets the TDRE flag to 1 and starts transmitting. If the TIE bit is set to 1 in SCR, the SCI requests a transmit-data-empty interrupt (TXI) at this time. Serial transmit data is transmitted in the following order from the TxD pin: Start bit: Transmit data: Parity bit or multiprocessor bit: One 0 bit is output. 7 or 8 bits are output, LSB first. One parity bit (even or odd parity) or one multiprocessor bit is output. Formats in which neither a parity bit nor a multiprocessor bit is output can also be selected. One or two 1 bits (stop bits) are output. Output of 1 continues until the start bit of the next transmit data.
Stop bit: Mark state:
* The SCI checks the TDRE flag when it outputs the stop bit. If the TDRE flag is 0, the SCI loads new data from TDR into TSR, outputs the stop bit, then begins serial transmission of the next frame. If the TDRE flag is 1, the SCI sets the TEND flag to 1 in SSR, outputs the stop bit, then continues output of 1 in the mark state. If the TEIE bit is set to 1 in SCR, a transmit-end interrupt (TEI) is requested at this time. Figure 11.6 shows an example of SCI transmit operation in asynchronous mode.
Start bit
0
1
Data D0 D1 D7
Parity Stop Start bit bit bit 0/1
1 0
Data D0 D1 D7
Parity Stop bit bit 0/1
1
1
Idle (mark) state
TDRE TEND
TXI interrupt request
TXI interrupt handler writes data in TDR and clears TDRE flag to 0 1 frame
TXI interrupt request
TEI interrupt request
Figure 11.6 Example of SCI Transmit Operation in Asynchronous Mode (8-Bit Data with Parity and 1 Stop Bit)
Rev.2.00 Mar. 22, 2007 Page 367 of 684 REJ09B0352-0200
11. Serial Communication Interface
Receiving Serial Data (Asynchronous Mode): Figure 11.7 shows a sample flowchart for receiving serial data and indicates the procedure to follow.
Initialize 1 1. SCI initialization: the receive data function of the RxD pin is selected automatically. 2., 3. Receive error handling and break detection: if a receive error occurs, read the ORER, PER, and FER flags in SSR to identify the error. After executing the necessary error handling, clear the ORER, PER, and FER flags all to 0. Receiving cannot resume if any of the ORER, PER, and FER flags remains set to 1. When a framing error occurs, the RxD pin can be read to detect the break state. 4. SCI status check and receive data read: read SSR, check that RDRF is set to 1, then read receive data from RDR and clear the RDRF flag to 0. Notification that the RDRF flag has changed from 0 to 1 can also be given by the RXI interrupt. 5. To continue receiving serial data: check the RDRF flag, read RDR, and clear the RDRF flag to 0 before the stop bit of the current frame is received.
Start receiving
Read ORER, PER, and FER flags in SSR
2
PER FER ORER = 1? No
Yes 3 Error handling (continued on next page)
Read RDRF flag in SSR
4
No RDRF = 1? Yes Read receive data from RDR, and clear RDRF flag to 0 in SSR
No
Finished receiving? Yes Clear RE bit to 0 in SCR End
5
Figure 11.7 Sample Flowchart for Receiving Serial Data (1)
Rev.2.00 Mar. 22, 2007 Page 368 of 684 REJ09B0352-0200
11. Serial Communication Interface
3 Error handling
No
ORER = 1? Yes Overrun error handling
No
FER = 1? Yes Break? No Framing error handling Clear RE bit to 0 in SCR Yes
No
PER = 1? Yes Parity error handling
Clear ORER, PER, and FER flags to 0 in SSR
End
Figure 11.7 Sample Flowchart for Receiving Serial Data (2)
Rev.2.00 Mar. 22, 2007 Page 369 of 684 REJ09B0352-0200
11. Serial Communication Interface
In receiving, the SCI operates as follows. * The SCI monitors the receive data line. When it detects a start bit, the SCI synchronizes internally and starts receiving. * Receive data is stored in RSR in order from LSB to MSB. * The parity bit and stop bit are received. After receiving data, the SCI makes the following checks: Parity check: Stop bit check: Status check: The number of 1s in the receive data must match the even or odd parity setting of the O/E bit in SMR. The stop bit value must be 1. If there are two stop bits, only the first stop bit is checked. The RDRF flag must be 0 so that receive data can be transferred from RSR into RDR.
If these checks all pass, the RDRF flag is set to 1 and the received data is stored in RDR. If one of the checks fails (receive error), the SCI operates as indicated in table 11.11. Note: When a receive error occurs, further receiving is disabled. In receiving, the RDRF flag is not set to 1. Be sure to clear the error flags. * When the RDRF flag is set to 1, if the RIE bit is set to 1 in SCR, a receive-data-full interrupt (RXI) is requested. If the ORER, PER, or FER flag is set to 1 and the RIE bit in SCR is also set to 1, a receive-error interrupt (ERI) is requested. Table 11.11 Receive Error Conditions
Receive Error Overrun error Abbreviation ORER Condition Data Transfer
Receiving of next data ends Receive data not while RDRF flag is still set transferred from RSR to to 1 in SSR RDR Stop bit is 0 Receive data transferred from RSR to RDR
Framing error Parity error
FER PER
Parity of receive data differs Receive data transferred from even/odd parity setting from RSR to RDR in SMR
Rev.2.00 Mar. 22, 2007 Page 370 of 684 REJ09B0352-0200
11. Serial Communication Interface
Figure 11.8 shows an example of SCI receive operation in asynchronous mode.
Start bit
0
1
Data D0 D1 D7
Parity Stop Start bit bit bit 0/1
1 0
Data D0 D1 D7
Parity Stop bit bit 0/1
1
1
Idle (mark) state
RDRF
FER RXI request 1 frame RXI interrupt handler reads data in RDR and clears RDRF flag to 0
Framing error, ERI request
Figure 11.8 Example of SCI Receive Operation (8-Bit Data with Parity and One Stop Bit) 11.3.3 Multiprocessor Communication
The multiprocessor communication function enables several processors to share a single serial communication line. The processors communicate in asynchronous mode using a format with an additional multiprocessor bit (multiprocessor format). In multiprocessor communication, each receiving processor is addressed by an ID. A serial communication cycle consists of an ID-sending cycle that identifies the receiving processor, and a data-sending cycle. The multiprocessor bit distinguishes ID-sending cycles from data-sending cycles. The transmitting processor starts by sending the ID of the receiving processor with which it wants to communicate as data with the multiprocessor bit set to 1. Next the transmitting processor sends transmit data with the multiprocessor bit cleared to 0. Receiving processors skip incoming data until they receive data with the multiprocessor bit set to 1. When they receive data with the multiprocessor bit set to 1, receiving processors compare the data with their IDs. The receiving processor with a matching ID continues to receive further incoming data. Processors with IDs not matching the received data skip further incoming data until they again receive data with the multiprocessor bit set to 1. Multiple processors can send and receive data in this way. Figure 11.9 shows an example of communication among different processors using a multiprocessor format.
Rev.2.00 Mar. 22, 2007 Page 371 of 684 REJ09B0352-0200
11. Serial Communication Interface
Communication Formats: Four formats are available. Parity-bit settings are ignored when a multiprocessor format is selected. For details see table 11.11. Clock: See section 11.3.2, Operation in Asynchronous Mode, Clock.
Transmitting processor
Serial communication line
Receiving processor A (ID = 01)
Receiving processor B
Receiving processor C
Receiving processor D
(ID = 02)
(ID = 03)
(ID = 04)
Serial data
H'01 (MPB = 1)
ID-sending cycle: receiving processor address
H'AA (MPB = 0)
Data-sending cycle: data sent to receiving processor specified by ID
Legend MPB: Multiprocessor bit
Figure 11.9 Example of Communication among Processors using Multiprocessor Format (Sending Data H'AA to Receiving Processor A)
Rev.2.00 Mar. 22, 2007 Page 372 of 684 REJ09B0352-0200
11. Serial Communication Interface
Transmitting and Receiving Data Transmitting Multiprocessor Serial Data: Figure 11.10 shows a sample flowchart for transmitting multiprocessor serial data and indicates the procedure to follow.
Initialize Start transmitting 1 1. SCI initialization: the transmit data output function of the TxD pin is selected automatically. 2. SCI status check and transmit data write: read SSR, check that the TDRE flag is 1, then write transmit data in TDR. Also set the MPBT flag to 0 or 1 in SSR. Finally, clear the TDRE flag to 0. 3. To continue transmitting serial data: after checking that the TDRE flag is 1, indicating that data can be written, write data in TDR, then clear the TDRE flag to 0. 4. To output a break signal at the end of serial transmission: set the DDR bit to 1 and clear the DR bit to 0 (DDR and DR are I/O port registers), then clear the TE bit to 0 in SCR.
Read TDRE flag in SSR TDRE = 1? Yes Write transmit data in TDR and set MPBT bit in SSR Clear TDRE flag to 0 No No
2
All data transmitted? Yes Read TEND flag in SSR
3
TEND = 1? Yes Output break signal? Yes Clear DR bit to 0, set DDR bit to 1 Clear TE bit to 0 in SCR
No
No
4
End
Figure 11.10 Sample Flowchart for Transmitting Multiprocessor Serial Data
Rev.2.00 Mar. 22, 2007 Page 373 of 684 REJ09B0352-0200
11. Serial Communication Interface
In transmitting serial data, the SCI operates as follows. * The SCI monitors the TDRE flag in SSR. When the TDRE flag is cleared to 0 the SCI recognizes that TDR contains new data, and loads this data from TDR into TSR. * After loading the data from TDR into TSR, the SCI sets the TDRE flag to 1 and starts transmitting. If the TIE bit in SCR is set to 1, the SCI requests a transmit-data-empty interrupt (TXI) at this time. Serial transmit data is transmitted in the following order from the TxD pin: Start bit: Transmit data: Stop bit: Mark state: One 0 bit is output. 7 or 8 bits are output, LSB first. One or two 1 bits (stop bits) are output. Output of 1 bits continues until the start bit of the next transmit data.
Multiprocessor bit: One multiprocessor bit (MPBT value) is output.
* The SCI checks the TDRE flag when it outputs the stop bit. If the TDRE flag is 0, the SCI loads data from TDR into TSR, outputs the stop bit, then begins serial transmission of the next frame. If the TDRE flag is 1, the SCI sets the TEND flag in SSR to 1, outputs the stop bit, then continues output of 1 bits in the mark state. If the TEIE bit is set to 1 in SCR, a transmit-end interrupt (TEI) is requested at this time. Figure 11.11 shows an example of SCI transmit operation using a multiprocessor format.
Multiprocessor bit
1
Multiprocessor bit Data D0 D1 D7 0/1 Stop bit
1 1
Start bit
0
Data D0 D1 D7 0/1
Stop Start bit bit
1 0
Serial data
Idle (mark) state
TDRE TEND
TXI request
TXI interrupt handler writes data in TDR and clears TDRE flag to 0 1 frame
TXI request
TEI request
Figure 11.11 Example of SCI Transmit Operation (8-Bit Data with Multiprocessor Bit and One Stop Bit)
Rev.2.00 Mar. 22, 2007 Page 374 of 684 REJ09B0352-0200
11. Serial Communication Interface
Receiving Multiprocessor Serial Data: Figure 11.12 shows a sample flowchart for receiving multiprocessor serial data and indicates the procedure to follow.
Initialize Start receiving 1 1. SCI initialization: the receive data function of the RxD pin is selected automatically. 2. ID receive cycle: set the MPIE bit to 1 in SCR. 3. SCI status check and ID check: read SSR, check that the RDRF flag is set to 1, then read data from RDR and compare with the processor's own ID. If the ID does not match, set the MPIE bit to 1 again and clear the RDRF flag to 0. If the ID matches, clear the RDRF flag to 0. 4. SCI status check and data receiving: read SSR, check that the RDRF flag is set to 1, then read data from RDR. 5. Receive error handling and break detection: if a receive error occurs, read the ORER and FER flags in SSR to identify the error. After executing the necessary error handling, clear the ORER and FER flags both to 0. Receiving cannot resume while either the ORER or FER flag remains set to 1. When a framing error occurs, the RxD pin can be read to detect the break state.
Set MPIE bit to 1 in SCR
2
Read ORER and FER flags in SSR Yes
FER ORER = 1 ? No Read RDRF flag in SSR No RDRF = 1? Yes Read receive data from RDR No Own ID? Yes Read ORER and FER flags in SSR
3
FER ORER = 1 ? No Read RDRF flag in SSR
Yes
4 No
RDRF = 1? Yes Read receive data from RDR
No
Finished receiving? Yes Clear RE bit to 0 in SCR End
5 Error handling (continued on next page)
Figure 11.12 Sample Flowchart for Receiving Multiprocessor Serial Data (1)
Rev.2.00 Mar. 22, 2007 Page 375 of 684 REJ09B0352-0200
11. Serial Communication Interface
5 Error handling
No
ORER = 1? Yes Overrun error handling
No
FER = 1? Yes Break? No Framing error handling Clear RE bit to 0 in SCR Yes
Clear ORER and FER flags to 0 in SSR
End
Figure 11.12 Sample Flowchart for Receiving Multiprocessor Serial Data (2)
Rev.2.00 Mar. 22, 2007 Page 376 of 684 REJ09B0352-0200
11. Serial Communication Interface
Figure 11.13 shows an example of SCI receive operation using a multiprocessor format.
Start bit
0
1
Data (ID1)
MPB D7
1
Stop Start Data (data1) bit bit
1 0
MPB D7
0
Stop bit
1
1
D0
D1
D0
D1
Idle (mark) state
MPIE
RDRF
RDR value RXI request RXI handler reads (multiprocessor RDR data and clears interrupt), MPIE = 0 RDRF flag to 0
ID1 Not own ID, so MPIE bit is set to 1 again No RXI request, RDR not updated
a. Own ID does not match data
1
Start bit
0
Data (ID2)
MPB D7
1
Stop Start bit bit
1 0
Data (data2) MPB
Stop bit
1
1
D0
D1
D0
D1
D7
0
Idle (mark) state
MPIE
RDRF
RDR value
ID1
ID2
Data 2
RXI request RXI interrupt handler Own ID, so receiving MPIE bit is set (multiprocessor reads RDR data and continues, with data to 1 again interrupt), MPIE = 0 clears RDRF flag to 0 received by RXI interrupt handler b. Own ID matches data
Figure 11.13 Example of SCI Receive Operation (8-Bit Data with Multiprocessor Bit and One Stop Bit)
Rev.2.00 Mar. 22, 2007 Page 377 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.3.4
Synchronous Operation
In synchronous mode, the SCI transmits and receives data in synchronization with clock pulses. This mode is suitable for high-speed serial communication. The SCI transmitter and receiver share the same clock but are otherwise independent, so full duplex communication is possible. The transmitter and receiver are also double buffered, so continuous transmitting or receiving is possible by reading or writing data while transmitting or receiving is in progress. Figure 11.14 shows the general format in synchronous serial communication.
Transfer direction One unit (character or frame) of serial data * Serial clock LSB Serial data Don't care Note: * High except in continuous transmitting or receiving Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 MSB Bit 7 Don't care *
Figure 11.14 Data Format in Synchronous Communication In synchronous serial communication, each data bit is placed on the communication line from one falling edge of the serial clock to the next. Data is guaranteed valid at the rise of the serial clock. In each character, the serial data bits are transmitted in order from LSB (first) to MSB (last). After output of the MSB, the communication line remains in the state of the MSB. In synchronous mode the SCI receives data by synchronizing with the rise of the serial clock. Communication Format: The data length is fixed at 8 bits. No parity bit or multiprocessor bit can be added. Clock: Either an internal clock generated by the built-in baud rate generator or an external serial clock input at the SCK pin can be selected, according to the setting of the C/A bit in SMR and the CKE1 and CKE0 bits in SCR. For details on SCI clock source selection, see table 11.9. When the SCI operates on an internal clock, it outputs the clock signal at the SCK pin. Eight clock pulses are output per transmitted or received character. When the SCI is not transmitting or receiving, the clock signal remains in the high state.
Rev.2.00 Mar. 22, 2007 Page 378 of 684 REJ09B0352-0200
11. Serial Communication Interface
Transmitting and Receiving Data SCI Initialization (Synchronous Mode): Before transmitting or receiving, clear the TE and RE bits to 0 in SCR, then initialize the SCI as follows. When changing the communication mode or format, always clear the TE and RE bits to 0 before following the procedure given below. Clearing the TE bit to 0 sets the TDRE flag to 1 and initializes TSR. Clearing the RE bit to 0, however, does not initialize the RDRF, PER, FER, and ORE flags and RDR, which retain their previous contents. Figure 11.15 shows a sample flowchart for initializing the SCI.
Start of initialization
Clear TE and RE bits to 0 in SCR
Set CKE1 and CKE0 bits in SCR (leaving TE and RE bits cleared to 0)
1
1. Select the clock source in SCR. Clear the RIE, TIE, TEIE, MPIE, TE, and RE bits to 0. 2. Select the communication format in SMR. 3. Write the value corresponding to the bit rate in BRR. This step is not necessary when an external clock is used. 4. Wait for at least the interval required to transmit or receive one bit, then set the TE or RE bit to 1 in SCR. Also set the RIE, TIE, and TEIE bits as necessary. Setting the TE or RE bit enables the SCI to use the TxD or RxD pin. Note: In simultaneous transmitting and receiving, the TE and RE bits should be cleared to 0 or set to 1 simultaneously.
2 Select communication format in SMR 3 Set value in BRR Wait 1 bit interval elapsed? Yes Set TE or RE to 1 in SCR Set RIE, TIE, and TEIE bits as necessary No
4
Start transmitting or receiving
Figure 11.15 Sample Flowchart for SCI Initialization
Rev.2.00 Mar. 22, 2007 Page 379 of 684 REJ09B0352-0200
11. Serial Communication Interface
Transmitting Serial Data (Synchronous Mode): Figure 11.16 shows a sample flowchart for transmitting serial data and indicates the procedure to follow.
Initialize 1 1. SCI initialization: the transmit data output function of the TxD pin is selected automatically. 2. SCI status check and transmit data write: read SSR, check that the TDRE flag is 1, then write transmit data in TDR and clear the TDRE flag to 0. 3. To continue transmitting serial data: after checking that the TDRE flag is 1, indicating that data can be written, write data in TDR, then clear the TDRE flag to 0.
Start transmitting
Read TDRE flag in SSR
2
No TDRE = 1? Yes Write transmit data in TDR and clear TDRE flag to 0 in SSR
All data transmitted? Yes
No
3
Read TEND flag in SSR No
TEND = 1? Yes Clear TE bit to 0 in SCR
End
Figure 11.16 Sample Flowchart for Serial Transmitting
Rev.2.00 Mar. 22, 2007 Page 380 of 684 REJ09B0352-0200
11. Serial Communication Interface
In transmitting serial data, the SCI operates as follows. * The SCI monitors the TDRE flag in SSR. When the TDRE flag is cleared to 0 the SCI recognizes that TDR contains new data, and loads this data from TDR into TSR. * After loading the data from TDR into TSR, the SCI sets the TDRE flag to 1 and starts transmitting. If the TIE bit is set to 1 in SCR, the SCI requests a transmit-data-empty interrupt (TXI) at this time. If clock output is selected, the SCI outputs eight serial clock pulses. If an external clock source is selected, the SCI outputs data in synchronization with the input clock. Data is output from the TxD pin in order from LSB (bit 0) to MSB (bit 7). * The SCI checks the TDRE flag when it outputs the MSB (bit 7). If the TDRE flag is 0, the SCI loads data from TDR into TSR and begins serial transmission of the next frame. If the TDRE flag is 1, the SCI sets the TEND flag to 1 in SSR, and after transmitting the MSB, holds the TxD pin in the MSB state. If the TEIE bit in SCR is set to 1, a transmit-end interrupt (TEI) is requested at this time. * After the end of serial transmission, the SCK pin is held in a constant state.
Rev.2.00 Mar. 22, 2007 Page 381 of 684 REJ09B0352-0200
11. Serial Communication Interface
Figure 11.17 shows an example of SCI transmit operation.
Transmit direction
Serial clock
Serial data TDRE TEND TXI request
Bit 0
Bit 1
Bit 7
Bit 0
Bit 1
Bit 6
Bit 7
TXI interrupt handler writes data in TDR and clears TDRE flag to 0 1 frame
TXI request
TEI request
Figure 11.17 Example of SCI Transmit Operation
Rev.2.00 Mar. 22, 2007 Page 382 of 684 REJ09B0352-0200
11. Serial Communication Interface
Receiving Serial Data (Synchronous Mode): Figure 11.18 shows a sample flowchart for receiving serial data and indicates the procedure to follow. When switching from asynchronous mode to synchronous mode, make sure that the ORER, PER, and FER flags are cleared to 0. If the FER or PER flag is set to 1 the RDRF flag will not be set and both transmitting and receiving will be disabled.
SCI initialization: the receive data function of the RxD pin is selected automatically. 2., 3. Receive error handling: if a receive error Start receiving occurs, read the ORER flag in SSR, then after executing the necessary error handling, clear the ORER flag to 0. Neither transmitting nor receiving can resume while the ORER flag Read ORER flag in SSR 2 remains set to 1. 4. SCI status check and receive data read: read SSR, check that the RDRF flag is set to 1, Yes ORER = 1? then read receive data from RDR and clear 3 the RDRF flag to 0. Notification that the RDRF Error handling No flag has changed from 0 to 1 can also be given by the RXI interrupt. (continued on next page) 5. To continue receiving serial data: check the Read RDRF flag in SSR 4 RDRF flag, read RDR, and clear the RDRF flag to 0 before the MSB (bit 7) of the current frame is received. RDRF = 1? Yes Read receive data from RDR, and clear RDRF flag to 0 in SSR Initialize 1 1.
No
No
Finished receiving? Yes Clear RE bit to 0 in SCR
5
End
Figure 11.18 Sample Flowchart for Serial Receiving (1)
Rev.2.00 Mar. 22, 2007 Page 383 of 684 REJ09B0352-0200
11. Serial Communication Interface
3 Error handling
Overrun error handling
Clear ORER flag to 0 in SSR
End
Figure 11.18 Sample Flowchart for Serial Receiving (2) In receiving, the SCI operates as follows. * The SCI synchronizes with serial clock input or output and initializes internally. * Receive data is stored in RSR in order from LSB to MSB. After receiving the data, the SCI checks that the RDRF flag is 0 so that receive data can be transferred from RSR to RDR. If this check passes, the RDRF flag is set to 1 and the received data is stored in RDR. If the check does not pass (receive error), the SCI operates as indicated in table 11.11. If any receive error is detected, the subsequent data transmission/reception is disabled. * After setting the RDRF flag to 1, if the RIE bit is set to 1 in SCR, the SCI requests a receivedata-full interrupt (RXI). If the ORER flag is set to 1 and the RIE bit in SCR is also set to 1, the SCI requests a receive-error interrupt (ERI).
Rev.2.00 Mar. 22, 2007 Page 384 of 684 REJ09B0352-0200
11. Serial Communication Interface
Figure 11.19 shows an example of SCI receive operation.
Serial clock
Serial data RDRF
Bit 7
Bit 0
Bit 7
Bit 0
Bit 1
Bit 6
Bit 7
ORER RXI request RXI interrupt handler reads data in RDR and clears RDRF flag to 0 1 frame RXI request Overrun error, ERI request
Figure 11.19 Example of SCI Receive Operation Transmitting and Receiving Serial Data Simultaneously (Synchronous Mode): Figure 11.20 shows a sample flowchart for transmitting and receiving serial data simultaneously and indicates the procedure to follow.
Rev.2.00 Mar. 22, 2007 Page 385 of 684 REJ09B0352-0200
11. Serial Communication Interface
1. SCI initialization: the transmit data output function of the TxD pin and receive data input function of the RxD pin are selected, enabling simultaneous transmitting and receiving. 2. SCI status check and transmit data write: read SSR, check that the TDRE flag is 1, then write transmit data in TDR and clear the TDRE flag to 0. Notification that the TDRE flag has changed from 0 to 1 can also be given by the TXI interrupt. 3. Receive error handling: if a receive error occurs, read the ORER flag in SSR, then after executing the necessary error handling, clear the ORER flag to 0. Neither transmitting nor receiving can resume while the ORER flag remains set to 1. 4. SCI status check and receive data read: read SSR, check that the RDRF flag is 1, then read receive data from RDR and clear the RDRF flag to 0. Notification that the RDRF flag has changed from 0 to 1 can also be given by the RXI interrupt. 5. To continue transmitting and receiving serial data: check the RDRF flag, read RDR, and clear the RDRF flag to 0 before the MSB (bit 7) of the current frame is received. Also check that the TDRE flag is set to 1, indicating that data can be written, write data in TDR, then clear the TDRE flag to 0 before the MSB (bit 7) of the current frame is transmitted.
Initialize Start transmitting and receiving
1
Read TDRE flag in SSR No TDRE = 1? Yes Write transmit data in TDR and clear TDRE flag to 0 in SSR
2
Read ORER flag in SSR Yes ORER = 1? 3 No Read RDRF flag in SSR No RDRF = 1? Yes Read receive data from RDR and clear RDRF flag to 0 in SSR Error handling 4
No
End of transmitting and receiving? Yes Clear TE and RE bits to 0 in SCR
5
End Note: When switching from transmitting or receiving to simultaneous transmitting and receiving, clear the TE and RE bits both to 0, then set the TE and RE bits both to 1.
Figure 11.20 Sample Flowchart for Serial Transmitting
Rev.2.00 Mar. 22, 2007 Page 386 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.4
SCI Interrupts
The SCI has four interrupt request sources: TEI (transmit-end interrupt), ERI (receive-error interrupt), RXI (receive-data-full interrupt), and TXI (transmit-data-empty interrupt). Table 11.12 lists the interrupt sources and indicates their priority. These interrupts can be enabled and disabled by the TIE, RIE, and TEIE bits in SCR. Each interrupt request is sent separately to the interrupt controller. The TXI interrupt is requested when the TDRE flag is set to 1 in SSR. The TEI interrupt is requested when the TEND flag is set to 1 in SSR. The RXI interrupt is requested when the RDRF flag is set to 1 in SSR. The ERI interrupt is requested when the ORER, PER, or FER flag is set to 1 in SSR. Table 11.12 SCI Interrupt Sources
Interrupt ERI RXI TXI TEI Description Receive error (ORER, FER, or PER) Receive data register full (RDRF) Transmit data register empty (TDRE) Transmit end (TEND) Low Priority High
Rev.2.00 Mar. 22, 2007 Page 387 of 684 REJ09B0352-0200
11. Serial Communication Interface
11.5
Usage Notes
Note the following points when using the SCI. TDR Write and TDRE Flag: The TDRE flag in SSR is a status flag indicating the loading of transmit data from TDR into TSR. The SCI sets the TDRE flag to 1 when it transfers data from TDR to TSR. Data can be written into TDR regardless of the state of the TDRE flag. If new data is written in TDR when the TDRE flag is 0, the old data stored in TDR will be lost because this data has not yet been transferred to TSR. Before writing transmit data in TDR, be sure to check that the TDRE flag is set to 1. Simultaneous Multiple Receive Errors: Table 11.13 indicates the state of SSR status flags when multiple receive errors occur simultaneously. When an overrun error occurs the RSR contents are not transferred to RDR, so receive data is lost. Table 11.13 SSR Status Flags and Transfer of Receive Data
SSR Status Flags RDRF 1 0 0 1 1 0 1 ORER 1 0 0 1 1 0 1 FER 0 1 0 1 0 1 1 PER 0 0 1 0 1 1 1 Receive Data Transfer RSR RDR Not transferred Transferred Transferred Not transferred Not transferred Transferred Not transferred Receive Errors Overrun error Framing error Parity error Overrun error + framing error Overrun error + parity error Framing error + parity error Overrun error + framing error + parity error
Rev.2.00 Mar. 22, 2007 Page 388 of 684 REJ09B0352-0200
11. Serial Communication Interface
Break Detection and Processing: Break signals can be detected by reading the RxD pin directly when a framing error (FER) is detected. In the break state the input from the RxD pin consists of all 0s, so the FER flag is set and the parity error flag (PER) may also be set. In the break state the SCI receiver continues to operate, so if the FER flag is cleared to 0 it will be set to 1 again. Sending a Break Signal: When the TE bit is cleared to 0 the TxD pin becomes an I/O port, the level and direction (input or output) of which are determined by DR and DDR bits. This feature can be used to send a break signal. After the serial transmitter is initialized, the DR value substitutes for the mark state until the TE bit is set to 1 (the TxD pin function is not selected until the TE bit is set to 1). The DDR and DR bits should therefore both be set to 1 beforehand. To send a break signal during serial transmission, clear the DR bit to 0, then clear the TE bit to 0. When the TE bit is cleared to 0 the transmitter is initialized, regardless of its current state, so the TxD pin becomes an input/output port outputting the value 0. Receive Error Flags and Transmitter Operation (Synchronous Mode Only): When a receive error flag (ORER, PER, or FER) is set to 1 the SCI will not start transmitting, even if the TDRE flag is cleared to 0. Be sure to clear the receive error flags to 0 when starting to transmit. Note that clearing the RE bit to 0 does not clear the receive error flags to 0. Receive Data Sampling Timing in Asynchronous Mode and Receive Margin: In asynchronous mode the SCI operates on a base clock with 16 times the bit rate frequency. In receiving, the SCI synchronizes internally with the fall of the start bit, which it samples on the base clock. Receive data is latched at the rising edge of the eighth base clock pulse. See figure 11.21.
Rev.2.00 Mar. 22, 2007 Page 389 of 684 REJ09B0352-0200
11. Serial Communication Interface
16 clocks 8 clocks 0 Internal base clock 7 15 0 7 15 0
Receive data (RxD)
Start bit
D0
D1
Synchronization sampling timing
Data sampling timing
Figure 11.21 Receive Data Sampling Timing in Asynchronous Mode The receive margin in asynchronous mode can therefore be expressed as shown in equation (1). M = | ( 0.5 - 1 2N ) - (L - 0.5) F - | D - 0.5 | N (1 + F) | x 100% ...............(1)
M: N: D: L: F:
Receive margin (%) Ratio of clock frequency to bit rate (N = 16) Clock duty cycle (D = 0 to 1.0) Frame length (L = 9 to 12) Absolute deviation of clock frequency
From equation (1), if F = 0 and D = 0.5 the receive margin is 46.875%, as given by equation (2). When D = 0.5, F = 0: M = [0.5 - 1/(2 x 16)] x 100% = 46.875% (2)
This is a theoretical value. A reasonable margin to allow in system design is 20% to 30%.
Restrictions in Synchronous Mode: When data transmission is performed using an external clock source as the serial clock, an interval of at least 5 states is necessary between clearing the
Rev.2.00 Mar. 22, 2007 Page 390 of 684 REJ09B0352-0200
11. Serial Communication Interface
TDRE flag in SSR and the start (falling edge) of the first transmit clock pulse corresponding to each frame (figure 11.22). This interval is also necessary when performing continuous transmission. If this condition is not satisfied, an operation error may occur.
SCK t* TDRE t*
TXD
X0
X1
X2
X3
X4
X5
X6
X7
Y0
Y1
Y2
Y3
Note: Make sure that t is at least 5 states.
Continuous transmission
Figure 11.22 Transmission in Synchronous Mode (Example) Restrictions when Switching from SCK Pin to Port Function in Synchronous SCI: 1. Problem in Operation After setting DDR and DR to 1 and using synchronous SCI clock output, when the SCK pin is switched to the port function at the end of transmission, a low-level signal is output for one halfcycle before the port output state is established. When switching to the port function by making the following settings while DDR = 1, DR = 1, C/A = 1, CKE1 = 0, CKE0 = 0, and TE = 1, low-level output occurs for one half-cycle. (1) End of serial data transmission (2) TE bit = 0 (3) C/A bit = 0 ... switchover to port output (4) Occurrence of low-level output (see figure 11.23)
Rev.2.00 Mar. 22, 2007 Page 391 of 684 REJ09B0352-0200
11. Serial Communication Interface
Half-cycle low-level output occurs SCK/port (1) End of transmission Data TE (3) C/A=0 C/A CKE1 CKE0 Bit 6 Bit 7 (2) TE=0 (4) Low-level output
Figure 11.23 Operation when Switching from SCK Pin Function to Port Pin Function 2. Usage Note The procedure shown below should be used to prevent low-level output when switching from the SCK pin function to the port function. As this procedure temporarily places the SCK pin in the input state, the SCK/port pin should be pulled up beforehand with an external circuit.With DDR = 1, DR = 1, C/A = 1, CKE1 = 0, CKE0 = 0, and TE = 1, make the following settings in the order shown. (1) End of serial data transmission (2) TE bit = 0 (3) CKE1 bit = 1 (4) C/A bit = 0 ... switchover to port output (5) CKE1 bit = 0
Rev.2.00 Mar. 22, 2007 Page 392 of 684 REJ09B0352-0200
11. Serial Communication Interface
High-level output SCK/port (1) End of transmission Data TE (4) C/A=0 C/A (3) CKE1=1 CKE1 CKE0 (5) CKE1=0 Bit 6 Bit 7 (2) TE=0
Figure 11.24 Operation when Switching from SCK Pin Function to Port Pin Function (Preventing Low-Level Output)
Rev.2.00 Mar. 22, 2007 Page 393 of 684 REJ09B0352-0200
11. Serial Communication Interface
Rev.2.00 Mar. 22, 2007 Page 394 of 684 REJ09B0352-0200
12. Smart Card Interface
Section 12 Smart Card Interface
12.1 Overview
SCI0 supports an IC card (Smart Card) interface conforming to ISO/IEC 7816-3 (Identification Card) as a serial communication interface extension function. Switching between the normal serial communication interface and the Smart Card interface is carried out by means of a register setting. 12.1.1 Features
Features of the Smart Card interface supported by the H8/3022 Group are as follows. * Asynchronous mode Data length: 8 bits Parity bit generation and checking Transmission of error signal (parity error) in receive mode Error signal detection and automatic data retransmission in transmit mode Direct convention and inverse convention both supported * On-chip baud rate generator allows any bit rate to be selected * Three interrupt sources Three interrupt sources (transmit data empty, receive data full, and transmit/receive error) that can issue requests independently
Rev.2.00 Mar. 22, 2007 Page 395 of 684 REJ09B0352-0200
12. Smart Card Interface
12.1.2
Block Diagram
Figure 12.1 shows a block diagram of the Smart Card interface.
Bus interface
Module data bus
Internal data bus
RDR
TDR
RxD0
RSR
TSR
SCMR SSR SCR SMR
Transmission/ reception control
BRR Baud rate generator /4 /16 /64 Clock
TxD0
Parity generation Parity check
SCK0 TXI RXI ERI
Legend SCMR RSR RDR TSR TDR SMR SCR SSR BRR
: Smart Card mode register : Receive shift register : Receive data register : Transmit shift register : Transmit data register : Serial mode register : Serial control register : Serial status register : Bit rate register
Figure 12.1 Block Diagram of Smart Card Interface
Rev.2.00 Mar. 22, 2007 Page 396 of 684 REJ09B0352-0200
12. Smart Card Interface
12.1.3
Pin Configuration
Table 12.1 shows the Smart Card interface pin configuration. Table 12.1 Smart Card Interface Pins
Pin Name Serial clock pin 0 Receive data pin 0 Transmit data pin 0 Abbreviation SCK0 RxD0 TxD0 I/O Output Input Output Function SCI0 clock output SCI0 receive data input SCI0 transmit data output
12.1.4
Register Configuration
Table 12.2 shows the registers used by the Smart Card interface. Details of SMR, BRR, SCR, TDR, and RDR are the same as for the normal SCI function: see the register descriptions in section 11, Serial Communication Interface. Table 12.2 Smart Card Interface Registers
Address* H'FFB0 H'FFB1 H'FFB2 H'FFB3 H'FFB4 H'FFB5 H'FFB6
1
Name Serial mode register Bit rate register Serial control register Transmit data register Serial status register Receive data register Smart card mode register
Abbreviation SMR BRR SCR TDR SSR RDR SCMR
R/W R/W R/W R/W R/W R/(W)* R R/W
2
Initial Value H'00 H'FF H'00 H'FF H'84 H'00 H'F2
Notes: 1. Lower 16 bits of the address. 2. Can only be written with 0 for flag clearing.
Rev.2.00 Mar. 22, 2007 Page 397 of 684 REJ09B0352-0200
12. Smart Card Interface
12.2
Register Descriptions
Registers added with the Smart Card interface and bits for which the function changes are described here. 12.2.1
Bit Initial value Read/Write
Smart Card Mode Register (SCMR)
7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 SDIR 0 R/W 2 SINV 0 R/W 1 -- 1 -- 0 SMIF 0 R/W
Reserved bits Smart card interface mode select Enables or disables the smart card interface function Smart card data invert Inverts data logic levels Smart card data transfer direction Selects the serial/parallel conversion format
SCMR is an 8-bit readable/writable register that selects the Smart Card interface function. SCMR is initialized to H'F2 by a reset, and in standby mode. Bits 7 to 4--Reserved: These bits cannot be modified and are always read as 1. Bit 3--Smart Card Data Transfer Direction (SDIR): Selects the serial/parallel conversion format.
Bit 3 SDIR 0 1 Description TDR contents are transmitted LSB-first Receive data is stored in RDR LSB-first TDR contents are transmitted MSB-first Receive data is stored in RDR MSB-first (Initial value)
Rev.2.00 Mar. 22, 2007 Page 398 of 684 REJ09B0352-0200
12. Smart Card Interface
Bit 2--Smart Card Data Invert (SINV): Specifies inversion of the data logic level. This function is used together with the SDIR bit for communication with an inverse convention card. The SINV bit does not affect the logic level of the parity bit. For parity-related setting procedures, see section 12.3.4, Register Settings.
Bit 2 SINV 0 1 Description TDR contents are transmitted as they are Receive data is stored as it is in RDR TDR contents are inverted before being transmitted Receive data is stored in inverted form in RDR (Initial value)
Bit 1--Reserved: This bit cannot be modified and is always read as 1. Bit 0--Smart Card Interface Mode Select (SMIF): This bit enables or disables the Smart Card interface function.
Bit 0 SMIF 0 1 Description Smart Card interface function is disabled Smart Card interface function is enabled (Initial value)
Rev.2.00 Mar. 22, 2007 Page 399 of 684 REJ09B0352-0200
12. Smart Card Interface
12.2.2
Bit
Serial Status Register (SSR)
7 TDRE 1 R/(W) * 6 RDRF 0 R/(W) * 5 ORER 0 R/(W) * 4 ERS 0 R/(W) * 3 PER 0 R/(W) * 2 TEND 1 R 1 MPB 0 R 0 MPBT 0 R/W
Initial value R/W
Transmit end Status flag indicating end of transmission Error signal status Status flag indicating that an error signal has been received Note: * Only 0 can be written to bits 7 to 3, to clear these flags.
Bit 4 of SSR has a different function in Smart Card interface mode. Coupled with this, the setting conditions for bit 2, TEND, are also different. Bits 7 to 5--Operate in the same way as for the normal SCI. For details, see section 11.2.7, Serial Status Register (SSR). Bit 4--Error Signal Status (ERS): In Smart Card interface mode, bit 4 indicates the status of the error signal sent back from the receiving end in transmission. Framing errors are not detected in Smart Card interface mode.
Bit 4 ERS 0 Description Indicates normal data transmission, with no error signal returned [Clearing conditions] Upon reset, in standby mode, or in module stop mode When 0 is written to ERS after reading ERS = 1 1 Indicates that the receiving device sent an error signal reporting a parity error [Setting condition] When the low level of the error signal is sampled Note: Clearing the TE bit in SCR to 0 does not affect the ERS flag, which retains its previous state. (Initial value)
Rev.2.00 Mar. 22, 2007 Page 400 of 684 REJ09B0352-0200
12. Smart Card Interface
Bits 3 to 0--Operate in the same way as for the normal SCI. For details, see section 11.2.7, Serial Status Register (SSR). However, the setting conditions for the TEND bit are as shown below.
Bit 2 TEND 0 Description Transmission is in progress [Clearing condition] When 0 is written to TDRE after reading TDRE = 1 1 End of transmission [Setting conditions] Upon reset and in standby mode When the TE bit in SCR is 0 and the ERS bit is also 0 When TDRE = 1 and ERS = 0 (normal transmission) 2.5 etu after transmission of a 1byte serial character Note: etu: Elementary Time Unit (time for transfer of 1 bit) (Initial value)
Rev.2.00 Mar. 22, 2007 Page 401 of 684 REJ09B0352-0200
12. Smart Card Interface
12.3
12.3.1
Operation
Overview
The main functions of the Smart Card interface are as follows. * One frame consists of 8-bit and plus a parity bit. * In transmission, a guard time of at least 2 etu (Elementary Time Unit: the time for transfer of one bit) is left between the end of the parity bit and the start of the next frame. * If a parity error is detected during reception, a low error signal level is output for one etu period, 10.5 etu after the start bit. * If the error signal is sampled during transmission, the same data is transmitted automatically after the elapse of 2 etu or longer. * Only asynchronous communication is supported; there is no clocked synchronous communication function. 12.3.2 Pin Connections
Figure 12.2 shows a schematic diagram of Smart Card interface related pin connections. In communication with an IC card, since both transmission and reception are carried out on a single data transmission line, the TxD0 pin and RxD0 pin should be connected with the LSI pin. The data transmission line should be pulled up to the VCC power supply with a resistor. When the clock generated on the Smart Card interface is used by an IC card, the SCK0 pin output is input to the CLK pin of the IC card. No connection is needed if the IC card uses an internal clock. LSI port output is used as the reset signal. Other pins must normally be connected to the power supply or ground.
Rev.2.00 Mar. 22, 2007 Page 402 of 684 REJ09B0352-0200
12. Smart Card Interface
VCC
TxD0 RxD0 SCK0 Clock line Px (port) H8/3022 Group Chip Connected equipment Reset line Data line
I/O
CLK RST IC card
Figure 12.2 Schematic Diagram of Smart Card Interface Pin Connections Note: If an IC card is not connected, and the TE and RE bits are both set to 1, closed transmission/reception is possible, enabling self-diagnosis to be carried out.
Rev.2.00 Mar. 22, 2007 Page 403 of 684 REJ09B0352-0200
12. Smart Card Interface
12.3.3
Data Format
Figure 12.3 shows the Smart Card interface data format. In reception in this mode, a parity check is carried out on each frame, and if an error is detected an error signal is sent back to the transmitting end, and retransmission of the data is requested. If an error signal is sampled during transmission, the same data is retransmitted.
When there is no parity error Ds D0 D1 D2 D3 D4 D5 D6 D7 Dp
Transmitting station output
When a parity error occurs Ds D0 D1 D2 D3 D4 D5 D6 D7 Dp DE
Transmitting station output Legend Ds D0 to D7 Dp DE Receiving station output : Start bit : Data bits : Parity bit : Error signal
Figure 12.3 Smart Card Interface Data Format
Rev.2.00 Mar. 22, 2007 Page 404 of 684 REJ09B0352-0200
12. Smart Card Interface
The operation sequence is as follows. [1] When the data line is not in use it is in the high-impedance state, and is fixed high with a pullup resistor. [2] The transmitting station starts a date transfer of one frame. The data frame starts with a start bit (Ds, low-level). Then 8 data bits (D0 to D7) and a parity bit (Dp) follows. [3] With the Smart Card interface, the data line then returns to the high-impedance state. The data line is pulled high with a pull-up resistor. [4] The receiving station carries out a parity check. If there is no parity error and the data is received normally, the receiving station waits for reception of the next data. If a parity error occurs, however, the receiving station outputs an error signal (DE, low-level) to request retransmission of the data. After outputting the error signal for the prescribed length of time, the receiving station places the signal line in the high-impedance state again. The signal line is pulled high again by a pull-up resistor. [5] If the transmitting station does not receive an error signal, it proceeds to transmit the next data frame. If it does receive an error signal, however, it returns to step [2] and retransmits the erroneous data.
Rev.2.00 Mar. 22, 2007 Page 405 of 684 REJ09B0352-0200
12. Smart Card Interface
12.3.4
Register Settings
Table 12.3 shows a bit map of the registers used by the smart card interface. Bits indicated as 0 or 1 must be set to the value shown. The setting of other bits is described below. Table 12.3 Smart Card Interface Register Settings
Bit Register SMR BRR SCR TDR SSR RDR SCMR Legend: Bit 7 0 BRR7 TIE TDR7 TDRE RDR7 -- --: Bit 6 0 BRR6 RIE TDR6 RDRF RDR6 -- Unused bit. Bit 5 1 BRR5 TE TDR5 ORER RDR5 -- Bit 4 O/E BRR4 RE TDR4 ERS RDR4 -- Bit 3 1 BRR3 0 TDR3 PER RDR3 SDIR Bit 2 0 BRR2 0 TDR2 TEND RDR2 SINV Bit 1 CKS1 BRR1 0 TDR1 0 RDR1 -- Bit 0 CKS0 BRR0 CKE0 TDR0 0 RDR0 SMIF
SMR Setting: The O/E bit is cleared to 0 if the IC card is of the direct convention type, and set to 1 if of the inverse convention type. Bits CKS1 and CKS0 select the clock source of the on-chip baud rate generator. See section 12.3.5, Clock. BRR Setting: BRR is used to set the bit rate. See section 12.3.5, Clock, for the method of calculating the value to be set. SCR Setting: The function of the TIE, RIE, TE, and RE bits is the same as for the normal SCI. For details, see section 11, Serial Communication Interface. Bit CKE0 specifies the clock output. Set these bits to 0 if a clock is not to be output, or to 1 if a clock is to be output.
Rev.2.00 Mar. 22, 2007 Page 406 of 684 REJ09B0352-0200
12. Smart Card Interface
SCMR Setting: The SDIR bit is cleared to 0 if the IC card is of the direct convention type, and set to 1 if of the inverse convention type. The SINV bit is cleared to 0 if the IC card is of the direct convention type, and set to 1 if of the inverse convention type. The SMIF bit is set to 1 in the case of the Smart Card interface. Examples of register settings and the waveform of the start character are shown below for the two types of IC card (direct convention and inverse convention). * Direct convention (SDIR = SINV = O/E = 0)
(Z) A Ds Z D0 Z D1 A D2 Z D3 Z D4 Z D5 A D6 A D7 Z Dp (Z) State
With the direct convention type, the logic 1 level corresponds to state Z and the logic 0 level to state A, and transfer is performed in LSB-first order. The start character data above is H'3B. The parity bit is 1 since even parity is stipulated for the Smart Card. * Inverse convention (SDIR = SINV = O/E = 1)
(Z) A Ds Z D7 Z D6 A D5 A D4 A D3 A D2 A D1 A D0 Z Dp (Z) State
With the inverse convention type, the logic 1 level corresponds to state A and the logic 0 level to state Z, and transfer is performed in MSB-first order. The start character data above is H'3F. The parity bit is 0, corresponding to state Z, since even parity is stipulated for the Smart Card. With the H8/3022 Group, inversion specified by the SINV bit applies only to the data bits, D7 to D0. For parity bit inversion, the O/E bit in SMR is set to odd parity mode (the same applies to both transmission and reception).
Rev.2.00 Mar. 22, 2007 Page 407 of 684 REJ09B0352-0200
12. Smart Card Interface
12.3.5
Clock
Only an internal clock generated by the on-chip baud rate generator can be used as the transmit/receive clock for the smart card interface. The bit rate is set with BRR and the CKS1 and CKS0 bits in SMR. The formula for calculating the bit rate is as shown below. Table 12.5 shows some sample bit rates. If clock output is selected by setting CKE0 to 1, a clock with a frequency of 372 times the bit rate is output from the SCK0 pin. B= 1488 x 2
2n-1
x (N + 1)
x 10
6
Where: N = Value set in BRR (0 N 255) B = Bit rate (bit/s) = Operating frequency* (MHz) n = See table 12.4 Table 12.4 Correspondence between n and CKS1, CKS0
n 0 1 2 3 1 CKS1 0 CKS0 0 1 0 1
Note: If the gear function is used to divide the system clock frequency,use the divided frequency to calculate the bit rate. The equation above applies directly to 1/1 frequency division.
Table 12.5 Examples of Bit Rate B (bit/s) for Various BRR Settings (When n = 0)
(MHz) N 0 1 2 7.1424 9600.0 4800.0 3200.0 10.00 13440.9 6720.4 4480.3 10.7136 14400.0 7200.0 4800.0 13.00 17473.1 8736.6 5824.4 14.2848 19200.0 9600.0 6400.0 16.00 21505.4 10752.7 7168.5 18.00 24193.5 12096.8 8064.5
Note: Bit rates are rounded off to one decimal place.
Rev.2.00 Mar. 22, 2007 Page 408 of 684 REJ09B0352-0200
12. Smart Card Interface
The method of calculating the value from the operating frequency and bit rate, on the other hand, is shown below. N is an integer, 0 N 255, and the smaller error is specified. N= 2n-1 1488 x 2 x B x 10 - 1
6
Table 12.6 Examples of BRR Settings for Bit Rate B (bit/s) (When n = 0)
(MHz) 7.1424 bit/s 9600 N Error 0 0.00 10.00 N Error 1 30 10.7136 N Error 1 25 13.00 N Error 1 8.99 14.2848 N Error 1 0.00 16.00 N Error 1 18.00 N Error 15.99
12.01 2
Table 12.7 Maximum Bit Rate at Various Frequencies (Smart Card Interface Mode)
(MHz) 7.1424 10.00 10.7136 13.00 14.2848 16.00 18.00 Maximum Bit Rate (bit/s) 9600 13441 14400 17473 19200 21505 24194 N 0 0 0 0 0 0 0 n 0 0 0 0 0 0 0
The bit rate error is given by the following formula: Error (%) = ( 1488 x 2
2n-1
6 x 10 - 1) x 100 x B x (N + 1)
Rev.2.00 Mar. 22, 2007 Page 409 of 684 REJ09B0352-0200
12. Smart Card Interface
12.3.6
Data Transfer Operations
Initialization: Before transmitting and receiving data, initialize the SCI as described below. Initialization is also necessary when switching from transmit mode to receive mode, or vice versa. [1] Clear the TE and RE bits in SCR to 0. [2] Clear the error flags ERS, PER, and ORER in SSR to 0. [3] Set the O/E bit and CKS1 and CKS0 bits in SMR. Clear the C/A, CHR, and MP bits to 0, and set the STOP and PE bits to 1. [4] Set the SMIF, SDIR, and SINV bits in SCMR. When the SMIF bit is set to 1, the TxD0 and RxD0 pins are both switched from ports to SCI pins, and are placed in the high-impedance state. [5] Set the value corresponding to the bit rate in BRR. [6] Set the CKE0 bit in SCR. Clear the TIE, RIE, TE, RE, MPIE, TEIE and CKE1 bits to 0. If the CKE0 bit is set to 1, the clock is output from the SCK0 pin. [7] Wait at least one bit interval, then set the TIE, RIE, TE, and RE bits in SCR. Do not set the TE bit and RE bit at the same time, except for self-diagnosis.
Rev.2.00 Mar. 22, 2007 Page 410 of 684 REJ09B0352-0200
12. Smart Card Interface
Serial Data Transmission: As data transmission in smart card mode involves error signal sampling and retransmission processing, the processing procedure is different from that for the normal SCI. Figure 12.4 shows an example of the transmission processing flow, and figure 12.5 shows the relation between a transmit operation and the internal registers. [1] Perform Smart Card interface mode initialization as described above in Initialization. [2] Check that the ERS error flag in SSR is cleared to 0. [3] Repeat steps [2] and [3] until it can be confirmed that the TEND flag in SSR is set to 1. [4] Write the transmit data to TDR, clear the TDRE flag to 0, and perform the transmit operation. The TEND flag is cleared to 0. [5] When transmitting data continuously, go back to step [2]. [6] To end transmission, clear the TE bit to 0.
With the above processing, interrupt servicing is possible. If transmission ends and the TEND flag is set to 1 while the TIE bit is set to 1 and interrupt requests are enabled, a transmit data empty interrupt (TXI) request will be generated. If an error occurs in transmission and the ERS flag is set to 1 while the RIE bit is set to 1 and interrupt requests are enabled, a transfer error interrupt (ERI) request will be generated. For details, see the following Interrupt Operations.
Rev.2.00 Mar. 22, 2007 Page 411 of 684 REJ09B0352-0200
12. Smart Card Interface
Start Initialization Start transmission
ERS=0? Yes
No
Error processing No TEND=1? Yes Write data to TDR, and clear TDRE flag in SSR to 0 No
All data transmitted? Yes No ERS=0? Yes Error processing
No TEND=1? Yes Clear TE bit to 0
End
Figure 12.4 Example of Transmission Processing Flow
Rev.2.00 Mar. 22, 2007 Page 412 of 684 REJ09B0352-0200
12. Smart Card Interface
TDR (1) Data write (2) Transfer from TDR to TSR (3) Serial data output Data 1 Data 1 Data 1 Data 1 ; Data remains in TDR Data 1 I/O signal line output TSR (shift register)
In case of normal transmission: TEND flag is set In case of transmit error: ERS flag is set Steps (2) and (3) above are repeated until the TEND flag is set Note: When the ERS flag is set, it should be cleared until transfer of the last bit (D7 in LSB-first transmission, D0 in MSB-first transmission) of the next transfer data has been completed.
Figure 12.5 Relation Between Transmit Operation and Internal Registers
Rev.2.00 Mar. 22, 2007 Page 413 of 684 REJ09B0352-0200
12. Smart Card Interface
Serial Data Reception: Data reception in Smart Card mode uses the same processing procedure as for the normal SCI. Figure 12.6 shows an example of the transmission processing flow. [1] Perform Smart Card interface mode initialization as described above in Initialization. [2] Check that the ORER flag and PER flag in SSR are cleared to 0. If either flag is set, perform the appropriate receive error processing, then clear both the ORER and the PER flag to 0. [3] Repeat steps [2] and [3] until it can be confirmed that the RDRF flag is set to 1. [4] Read the receive data from RDR. [5] When receiving data continuously, clear the RDRF flag to 0 and go back to step [2]. [6] To end reception, clear the RE bit to 0.
Start Initialization Start reception
ORER = 0 and PER = 0 Yes
No
Error processing No RDRF=1? Yes Read RDR and clear RDRF flag in SSR to 0
No
All data received? Yes Clear RE bit to 0
Figure 12.6 Example of Reception Processing Flow
Rev.2.00 Mar. 22, 2007 Page 414 of 684 REJ09B0352-0200
12. Smart Card Interface
With the above processing, interrupt servicing is possible. If reception ends and the RDRF flag is set to 1 while the RIE bit is set to 1 and interrupt requests are enabled, a receive data full interrupt (RXI) request will be generated. If an error occurs in reception and either the ORER flag or the PER flag is set to 1, a transfer error interrupt (ERI) request will be generated. For details, see Interrupt Operation below. If a parity error occurs during reception and the PER is set to 1, the received data is still transferred to RDR, and therefore this data can be read. Mode Switching Operation: When switching from receive mode to transmit mode, first confirm that the receive operation has been completed, then start from initialization, clearing RE bit to 0 and setting TE bit to 1. The RDRF flag or the PER and ORER flags can be used to check that the receive operation has been completed. When switching from transmit mode to receive mode, first confirm that the transmit operation has been completed, then start from initialization, clearing TE bit to 0 and setting RE bit to 1. The TEND flag can be used to check that the transmit operation has been completed. Interrupt Operation: There are three interrupt sources in smart card interface mode: transmit data empty interrupt (TXI) requests, transfer error interrupt (ERI) requests, and receive data full interrupt (RXI) requests. The transmit end interrupt (TEI) request is not used in this mode. When the TEND flag in SSR is set to 1, a TXI interrupt request is generated. When the RDRF flag in SSR is set to 1, an RXI interrupt request is generated. When any of flags ORER, PER, and ERS in SSR is set to 1, an ERI interrupt request is generated. The relationship between the operating states and interrupt sources is shown in table 12.8. Table 12.8 Smart Card Mode Operating States and Interrupt Sources
Operating State Transmit Mode Normal operation Error Receive Mode Normal operation Error Flag TEND ERS RDRF PER, ORER Mask Bit TIE RIE RIE RIE Interrupt Source TXI ERI RXI ERI
Rev.2.00 Mar. 22, 2007 Page 415 of 684 REJ09B0352-0200
12. Smart Card Interface
12.4
Usage Note
The following points should be noted when using the SCI as a smart card interface. Receive Data Sampling Timing and Reception Margin in Smart Card Interface Mode: In smart card interface mode, the SCI operates on a basic clock with a frequency of 372 times the transfer rate. In reception, the SCI samples the falling edge of the start bit using the basic clock, and performs internal synchronization. Receive data is latched internally at the rising edge of the 186th pulse of the basic clock. This is illustrated in figure 12.7.
372 clocks 186 clocks 0 185 371 0 185 371 0
Internal basic clock
Receive data (RxD)
Start bit
D0
D1
Synchronization sampling timing
Data sampling timing
Figure 12.7 Receive Data Sampling Timing in Smart Card Mode
Rev.2.00 Mar. 22, 2007 Page 416 of 684 REJ09B0352-0200
12. Smart Card Interface
Thus the reception margin in smart card interface mode is given by the following formula. M = (0.5 - 1 2N ) - (L - 0.5) F - D - 0.5 (1 + F) x 100% N
Where M: Reception margin (%) N: Ratio of bit rate to clock (N = 372) D: Clock duty (D = 0 to 1.0) L: Frame length (L = 10) F: Absolute value of clock frequency deviation Assuming values of F = 0 and D = 0.5 in the above formula, the reception margin formula is as follows. When D = 0.5 and F = 0, M = (0.5 - 1/2 x 372) x 100% = 49.866%
Retransfer Operations: Retransfer operations are performed by the SCI in receive mode and transmit mode as described below. * Retransfer operation when SCI is in receive mode Figure 12.8 illustrates the retransfer operation when the SCI is in receive mode. [1] If an error is found when the received parity bit is checked, the PER bit in SSR is automatically set to 1. If the RIE bit in SCR is enabled at this time, an ERI interrupt request is generated. The PER bit in SSR should be kept cleared to 0 until the next parity bit is sampled. [2] The RDRF bit in SSR is not set for a frame in which an error has occurred. [3] If no error is found when the received parity bit is checked, the PER bit in SSR is not set to 1. [4] If no error is found when the received parity bit is checked, the receive operation is judged to have been completed normally, and the RDRF flag in SSR is automatically set to 1. If the RIE bit in SCR is enabled at this time, an RXI interrupt request is generated. [5] When a normal frame is received, the pin retains the high-impedance state at the timing for error signal transmission.
Rev.2.00 Mar. 22, 2007 Page 417 of 684 REJ09B0352-0200
12. Smart Card Interface
nth transfer frame Ds D0 D1 D2 D3 D4 D5 D6 D7 Dp DE RDRF [2] PER [1]
Retransferred frame
Transfer frame n+1
(DE) Ds D0 D1 D2 D3 D4 D5 D6 D7 Dp Ds D0 D1 D2 D3 D4
[4]
[3]
Figure 12.8 Retransfer Operation in SCI Receive Mode * Retransfer operation when SCI is in transmit mode Figure 12.9 illustrates the retransfer operation when the SCI is in transmit mode. [6] If an error signal is sent back from the receiving end after transmission of one frame is completed, the ERS bit in SSR is set to 1. If the RIE bit in SCR is enabled at this time, an ERI interrupt request is generated. The ERS bit in SSR should be kept cleared to 0 until the next parity bit is sampled. [7] The TEND bit in SSR is not set for a frame for which an error signal indicating an abnormality is received. [8] If an error signal is not sent back from the receiving end, the ERS bit in SSR is not set. [9] If an error signal is not sent back from the receiving end, transmission of one frame, including a retransfer, is judged to have been completed, and the TEND bit in SSR is set to 1. If the TIE bit in SCR is enabled at this time, a TXI interrupt request is generated.
nth transfer frame Ds D0 D1 D2 D3 D4 D5 D6 D7 Dp DE TDRE Transfer to TSR from TDR TEND [7] ERS [6] [8] [9] Transfer to TSR from TDR Transfer to TSR from TDR Retransferred frame Ds D0 D1 D2 D3 D4 D5 D6 D7 Dp (DE) Transfer frame n+1 Ds D0 D1 D2 D3 D4
Figure 12.9 Retransfer Operation in SCI Transmit Mode
Rev.2.00 Mar. 22, 2007 Page 418 of 684 REJ09B0352-0200
13. A/D Converter
Section 13 A/D Converter
13.1 Overview
The H8/3022 Group includes a 10-bit successive-approximations A/D converter with a selection of up to eight analog input channels. When the A/D converter is not used, it can be halted independently to conserve power. For details see section 17.6, Module Standby Function. 13.1.1 Features
A/D converter features are listed below. * 10-bit resolution * Eight input channels * Selectable analog conversion voltage range The analog voltage conversion range can be programmed by input of an analog reference voltage at the AVCC pin. * High-speed conversion Conversion time: minimum 7.4 s per channel (with 18 MHz system clock) * Two conversion modes Single mode: A/D conversion of one channel Scan mode: continuous conversion on one to four channels * Four 16-bit data registers A/D conversion results are transferred for storage into data registers corresponding to the channels. * Sample-and-hold function * A/D conversion can be externally triggered * A/D interrupt requested at end of conversion At the end of A/D conversion, an A/D end interrupt (ADI) can be requested.
Rev.2.00 Mar. 22, 2007 Page 419 of 684 REJ09B0352-0200
13. A/D Converter
13.1.2
Block Diagram
Figure 13.1 shows a block diagram of the A/D converter.
Internal data bus
Bus interface ADDRC ADDRD ADDRA ADDRB ADCSR
Module data bus
AVCC 10-bit D/A AV SS
Successiveapproximations register
AN 0 AN 1 AN 2 AN 3 AN 4 AN 5 AN 6 AN 7 Analog multiplexer
+ - Comparator Control circuit Sample-andhold circuit /16 /8
ADCR
ADTRG Legend ADCR: ADCSR: ADDRA: ADDRB: ADDRC: ADDRD:
ADI interrupt
A/D control register A/D control/status register A/D data register A A/D data register B A/D data register C A/D data register D
Figure 13.1 A/D Converter Block Diagram
Rev.2.00 Mar. 22, 2007 Page 420 of 684 REJ09B0352-0200
13. A/D Converter
13.1.3
Pin Configuration
Table 13.1 summarizes the A/D converter's input pins. The eight analog input pins are divided into two groups: group 0 (AN0 to AN3), and group 1 (AN4 to AN7). AVCC and AVSS are the power supply for the analog circuits in the A/D converter. Table 13.1 A/D Converter Pins
Pin Name Analog power supply pin Analog ground pin Analog input pin 0 Analog input pin 1 Analog input pin 2 Analog input pin 3 Analog input pin 4 Analog input pin 5 Analog input pin 6 Analog input pin 7 A/D external trigger input pin Abbreviation AVCC AVSS AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 ADTRG I/O Function
Input Analog power supply and reference voltage Input Analog ground and reference voltage Input Group 0 analog inputs Input Input Input Input Group 1 analog inputs Input Input Input Input External trigger input for starting A/D conversion
Rev.2.00 Mar. 22, 2007 Page 421 of 684 REJ09B0352-0200
13. A/D Converter
13.1.4
Register Configuration
Table 13.2 summarizes the A/D converter's registers. Table 13.2 A/D Converter Registers
Address* H'FFE0 H'FFE1 H'FFE2 H'FFE3 H'FFE4 H'FFE5 H'FFE6 H'FFE7 H'FFE8 H'FFE9
1
Name A/D data register A (high) A/D data register A (low) A/D data register B (high) A/D data register B (low) A/D data register C (high) A/D data register C (low) A/D data register D (high) A/D data register D (low) A/D control/status register A/D control register
Abbreviation ADDRAH ADDRAL ADDRBH ADDRBL ADDRCH ADDRCL ADDRDH ADDRDL ADCSR ADCR
R/W R R R R R R R R R/(W)* R/W
2
Initial Value H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'00 H'7F
Notes: 1. Lower 16 bits of the address 2. Only 0 can be written in bit 7 to clear the flag.
Rev.2.00 Mar. 22, 2007 Page 422 of 684 REJ09B0352-0200
13. A/D Converter
13.2
13.2.1
Bit ADDRn
Register Descriptions
A/D Data Registers A to D (ADDRA to ADDRD)
15 0 R 14 0 R 13 0 R 12 0 R 11 0 R 10 0 R 9 0 R 8 0 R 7 0 R 6 0 R 5 0 R 4 -- 0 R 3 -- 0 R 2 -- 0 R 1 -- 0 R 0 -- 0 R
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 --
Initial value Read/Write (n = A to D)
A/D conversion data 10-bit data giving an A/D conversion result
Reserved bits
The four A/D data registers (ADDRA to ADDRD) are 16-bit read-only registers that store the results of A/D conversion. An A/D conversion produces 10-bit data, which is transferred for storage into the A/D data register corresponding to the selected channel. The upper 8 bits of the result are stored in the upper byte of the A/D data register. The lower 2 bits are stored in the lower byte. Bits 5 to 0 of an A/D data register are reserved bits that always read 0. Table 13.3 indicates the pairings of analog input channels and A/D data registers. The CPU can always read the A/D data registers. The upper byte can be read directly, but the lower byte is read through a temporary register (TEMP). For details see section 13.3, CPU Interface. The A/D data registers are initialized to H'0000 by a reset and in standby mode. Table 13.3 Analog Input Channels and A/D Data Registers
Analog Input Channel Group 0 AN0 AN1 AN2 AN3 Group 1 AN4 AN5 AN6 AN7 A/D Data Register ADDRA ADDRB ADDRC ADDRD
Rev.2.00 Mar. 22, 2007 Page 423 of 684 REJ09B0352-0200
13. A/D Converter
13.2.2
Bit
A/D Control/Status Register (ADCSR)
7 ADF 0 R/(W)* 6 ADIE 0 R/W 5 ADST 0 R/W 4 SCAN 0 R/W 3 CKS 0 R/W 2 CH2 0 R/W 1 CH1 0 R/W 0 CH0 0 R/W
Initial value Read/Write
Channel select 2 to 0 These bits select analog input channels Clock select Selects the A/D conversion time Scan mode Selects single mode or scan mode A/D start Starts or stops A/D conversion A/D interrupt enable Enables and disables A/D end interrupts A/D end flag Indicates end of A/D conversion Note: * Only 0 can be written to clear the flag.
ADCSR is an 8-bit readable/writable register that selects the mode and controls the A/D converter. ADCSR is initialized to H'00 by a reset and in standby mode.
Rev.2.00 Mar. 22, 2007 Page 424 of 684 REJ09B0352-0200
13. A/D Converter
Bit 7--A/D End Flag (ADF): Indicates the end of A/D conversion.
Bit 7 ADF 0 1 Description [Clearing condition] Cleared by reading ADF while ADF = 1, then writing 0 in ADF [Setting conditions] Single mode: A/D conversion ends Scan mode: A/D conversion ends in all selected channels (Initial value)
Bit 6--A/D Interrupt Enable (ADIE): Enables or disables the interrupt (ADI) requested at the end of A/D conversion.
Bit 6 ADIE 0 1 Description A/D end interrupt request (ADI) is disabled A/D end interrupt request (ADI) is enabled (Initial value)
Bit 5--A/D Start (ADST): Starts or stops A/D conversion. The ADST bit remains set to 1 during A/D conversion. It can also be set to 1 by external trigger input at the ADTRG pin.
Bit 5 ADST 0 1 Description A/D conversion is stopped (Initial value)
Single mode: A/D conversion starts; ADST is automatically cleared to 0 when conversion ends. Scan mode: A/D conversion starts and continues, cycling among the selected channels, until ADST is cleared to 0 by software, by a reset, or by a transition to standby mode.
Rev.2.00 Mar. 22, 2007 Page 425 of 684 REJ09B0352-0200
13. A/D Converter
Bit 4--Scan Mode (SCAN): Selects single mode or scan mode. For further information on operation in these modes, see section 13.4, Operation. Clear the ADST bit to 0 before switching the conversion mode.
Bit 4 SCAN 0 1 Description Single mode Scan mode (Initial value)
Bit 3--Clock Select (CKS): Selects the A/D conversion time. Clear the ADST bit to 0 before switching the conversion time.
Bit 3 CKS 0 1 Description Conversion time = 266 states (maximum) Conversion time = 134 states (maximum) (Initial value)
Bits 2 to 0--Channel Select 2 to 0 (CH2 to CH0): These bits and the SCAN bit select the analog input channels. Clear the ADST bit to 0 before changing the channel selection.
Group Selection CH2 0 Channel Selection CH1 0 CH0 0 1 1 0 1 1 0 0 1 1 0 1 Single Mode AN0 (Initial value) AN1 AN2 AN3 AN4 AN5 AN6 AN7 Description Scan Mode AN0 AN0, AN1 AN0 to AN2 AN0 to AN3 AN4 AN4, AN5 AN4 to AN6 AN4 to AN7
Rev.2.00 Mar. 22, 2007 Page 426 of 684 REJ09B0352-0200
13. A/D Converter
13.2.3
Bit
A/D Control Register (ADCR)
7 TRGE 0 R/W 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 -- 1 -- Reserved bits Trigger enable Enables or disables external triggering of A/D conversion 2 -- 1 -- 1 -- 1 -- 0 -- 1 --
Initial value Read/Write
ADCR is an 8-bit readable/writable register that enables or disables external triggering of A/D conversion. ADCR is initialized to H'7F by a reset and in standby mode. Bit 7--Trigger Enable (TRGE): Enables or disables external triggering of A/D conversion.
Bit 7 TRGE 0 1 Description A/D conversion cannot be externally triggered (Initial value)
A/D conversion starts at the falling edge of the external trigger signal (ADTRG)
Bits 6 to 0--Reserved: These bits cannot be modified and are always read as 1.
Rev.2.00 Mar. 22, 2007 Page 427 of 684 REJ09B0352-0200
13. A/D Converter
13.3
CPU Interface
ADDRA to ADDRD are 16-bit registers, but they are connected to the CPU by an 8-bit data bus. Therefore, although the upper byte can be be accessed directly by the CPU, the lower byte is read through an 8-bit temporary register (TEMP). An A/D data register is read as follows. When the upper byte is read, the upper-byte value is transferred directly to the CPU and the lower-byte value is transferred into TEMP. Next, when the lower byte is read, the TEMP contents are transferred to the CPU. When reading an A/D data register, always read the upper byte before the lower byte. It is possible to read only the upper byte, but if only the lower byte is read, incorrect data may be obtained. Figure 13.2 shows the data flow for access to an A/D data register.
Upper-byte read
CPU (H'AA)
Module data bus Bus interface
TEMP (H'40)
ADDRnH (H'AA)
ADDRnL (H'40) (n = A to D)
Lower-byte read
CPU (H'40)
Module data bus Bus interface
TEMP (H'40)
ADDRnH (H'AA)
ADDRnL (H'40) (n = A to D)
Figure 13.2 A/D Data Register Access Operation (Reading H'AA40)
Rev.2.00 Mar. 22, 2007 Page 428 of 684 REJ09B0352-0200
13. A/D Converter
13.4
Operation
The A/D converter operates by successive approximations with 10-bit resolution. It has two operating modes: single mode and scan mode. 13.4.1 Single Mode (SCAN = 0)
Single mode should be selected when only one A/D conversion on one channel is required. A/D conversion starts when the ADST bit is set to 1 by software, or by external trigger input. The ADST bit remains set to 1 during A/D conversion and is automatically cleared to 0 when conversion ends. When conversion ends the ADF bit is set to 1. If the ADIE bit is also set to 1, an ADI interrupt is requested at this time. To clear the ADF flag to 0, first read ADCSR, then write 0 in ADF. When the mode or analog input channel must be switched during analog conversion, to prevent incorrect operation, first clear the ADST bit to 0 in ADCSR to halt A/D conversion. After making the necessary changes, set the ADST bit to 1 to start A/D conversion again. The ADST bit can be set at the same time as the mode or channel is changed. Typical operations when channel 1 (AN1) is selected in single mode are described next. Figure 13.3 shows a timing diagram for this example. 1. Single mode is selected (SCAN = 0), input channel AN1 is selected (CH2 = CH1 = 0, CH0 = 1), the A/D interrupt is enabled (ADIE = 1), and A/D conversion is started (ADST = 1). 2. When A/D conversion is completed, the result is transferred into ADDRB. At the same time the ADF flag is set to 1, the ADST bit is cleared to 0, and the A/D converter becomes idle. 3. Since ADF = 1 and ADIE = 1, an ADI interrupt is requested. 4. The A/D interrupt handling routine starts. 5. The routine reads ADCSR, then writes 0 in the ADF flag. 6. The routine reads and processes the conversion result (ADDRB). 7. Execution of the A/D interrupt handling routine ends. After that, if the ADST bit is set to 1, A/D conversion starts again and steps 2 to 7 are repeated.
Rev.2.00 Mar. 22, 2007 Page 429 of 684 REJ09B0352-0200
Set *
ADIE A/D conversion starts Clear * Clear * Set * Set *
13. A/D Converter
ADST
ADF Idle
State of channel 0 (AN 0) Idle
A/D conversion (1)
Rev.2.00 Mar. 22, 2007 Page 430 of 684 REJ09B0352-0200
Idle
A/D conversion (2)
State of channel 1 (AN 1) Idle
Idle
State of channel 2 (AN 2) Idle
State of channel 3 (AN 3)
ADDRA Read conversion result A/D conversion result (1) Read conversion result A/D conversion result (2)
ADDRB
Figure 13.3 Example of A/D Converter Operation (Single Mode, Channel 1 Selected)
ADDRC
ADDRD
Note: * Vertical arrows ( ) indicate instructions executed by software.
13. A/D Converter
13.4.2
Scan Mode (SCAN = 1)
Scan mode is useful for monitoring analog inputs in a group of one or more channels. When the ADST bit is set to 1 by software or external trigger input, A/D conversion starts on the first channel in the group (AN0 when CH2 = 0, AN4 when CH2 = 1). When two or more channels are selected, after conversion of the first channel ends, conversion of the second channel (AN1 or AN5) starts immediately. A/D conversion continues cyclically on the selected channels until the ADST bit is cleared to 0. The conversion results are transferred for storage into the A/D data registers corresponding to the channels. When the mode or analog input channel selection must be changed during analog conversion, to prevent incorrect operation, first clear the ADST bit to 0 in ADCSR to halt A/D conversion. After making the necessary changes, set the ADST bit to 1. A/D conversion will start again from the first channel in the group. The ADST bit can be set at the same time as the mode or channel selection is changed. Typical operations when three channels in group 0 (AN0 to AN2) are selected in scan mode are described next. Figure 13.4 shows a timing diagram for this example. 1. Scan mode is selected (SCAN = 1), scan group 0 is selected (CH2 = 0), analog input channels AN0 to AN2 are selected (CH1 = 1, CH0 = 0), and A/D conversion is started (ADST = 1). 2. When A/D conversion of the first channel (AN0) is completed, the result is transferred into ADDRA. Next, conversion of the second channel (AN1) starts automatically. 3. Conversion proceeds in the same way through the third channel (AN2). 4. When conversion of all selected channels (AN0 to AN2) is completed, the ADF flag is set to 1 and conversion of the first channel (AN0) starts again. If the ADIE bit is set to 1, an ADI interrupt is requested at this time. 5. Steps 2 to 4 are repeated as long as the ADST bit remains set to 1. When the ADST bit is cleared to 0, A/D conversion stops. After that, if the ADST bit is set to 1, A/D conversion starts again from the first channel (AN0).
Rev.2.00 Mar. 22, 2007 Page 431 of 684 REJ09B0352-0200
Continuous A/D conversion Set *1 Clear*1
13. A/D Converter
ADST Clear* 1 A/D conversion time Idle
A/D conversion (1)
ADF Idle A/D conversion (4) Idle
State of channel 0 (AN 0) Idle Idle A/D conversion (2)
Rev.2.00 Mar. 22, 2007 Page 432 of 684 REJ09B0352-0200
A/D conversion (5) * 2 Idle Idle A/D conversion (3) Idle Idle Transfer A/D conversion result (1) A/D conversion result (4) A/D conversion result (2) A/D conversion result (3)
State of channel 1 (AN 1)
State of channel 2 (AN 2)
State of channel 3 (AN 3)
ADDRA
ADDRB
Figure 13.4 Example of A/D Converter Operation (Scan Mode, Channels AN0 to AN2 Selected)
ADDRC
ADDRD
Notes: 1. Vertical arrows ( ) indicate instructions executed by software. 2. Data currently being converted is ignored.
13. A/D Converter
13.4.3
Input Sampling and A/D Conversion Time
The A/D converter has a built-in sample-and-hold circuit. The A/D converter samples the analog input at a time tD after the ADST bit is set to 1, then starts conversion. Figure 13.5 shows the A/D conversion timing. Table 13.4 indicates the A/D conversion time. As indicated in figure 13.5, the A/D conversion time includes tD and the input sampling time. The length of tD varies depending on the timing of the write access to ADCSR. The total conversion time therefore varies within the ranges indicated in table 13.4. In scan mode, the values given in table 13.4 apply to the first conversion. In the second and subsequent conversions the conversion time is fixed at 256 states when CKS = 0 or 128 states when CKS = 1.
(1)
Address bus
(2)
Write signal
Input sampling timing
ADF tD tSPL tCONV Legend ADCSR write cycle (1): ADCSR address (2): Synchronization delay tD: tSPL: Input sampling time tCONV: A/D conversion time
Figure 13.5 A/D Conversion Timing
Rev.2.00 Mar. 22, 2007 Page 433 of 684 REJ09B0352-0200
13. A/D Converter
Table 13.4 A/D Conversion Time (Single Mode)
CKS = 0 Symbol Synchronization delay Input sampling time A/D conversion time tD tSPL tCONV Min 10 -- 259 Typ -- 63 -- Max 17 -- 266 CKS = 1 Min 6 -- 131 Typ -- 31 -- Max 9 -- 134
Note: Values in the table are numbers of states.
13.4.4
External Trigger Input Timing
A/D conversion can be externally triggered. When the TRGE bit is set to 1 in ADCR, external trigger input is enabled at the ADTRG pin. A high-to-low transition at the ADTRG pin sets the ADST bit to 1 in ADCSR, starting A/D conversion. Other operations, in both single and scan modes, are the same as if the ADST bit had been set to 1 by software. Figure 13.6 shows the timing.
ADTRG
Internal trigger signal
ADST A/D conversion
Figure 13.6 External Trigger Input Timing
Rev.2.00 Mar. 22, 2007 Page 434 of 684 REJ09B0352-0200
13. A/D Converter
13.5
Interrupts
The A/D converter generates an interrupt (ADI) at the end of A/D conversion. The ADI interrupt request can be enabled or disabled by the ADIE bit in ADCSR.
13.6
Usage Notes
The following points should be noted when using the A/D converter. Setting Range of Analog Power Supply and Other Pins: (1) Analog input voltage range The voltage applied to analog input pins AN0 to AN7 during A/D conversion should be in the range AVSS ANn AVCC. (2) Relation between AVCC, AVSS and VCC, VSS As the relationship between AVCC, AVSS and VCC, VSS, set AVSS = VSS. If the A/D converter is not used, the AVCC and AVSS pins must on no account be left open. If conditions (1) and (2) above are not met, the reliability of the device may be adversely affected. Notes on Board Design: In board design, digital circuitry and analog circuitry should be as mutually isolated as possible, and layout in which digital circuit signal lines and analog circuit signal lines cross or are in close proximity should be avoided as far as possible. Failure to do so may result in incorrect operation of the analog circuitry due to inductance, adversely affecting A/D conversion values. Also, digital circuitry must be isolated from the analog input signals (AN0 to AN7), and analog power supply and reference voltage (AVCC) by the analog ground (AVSS). Also, the analog ground (AVSS) should be connected at one point to a stable digital ground (VSS) on the board. Notes on Noise Countermeasures: A protection circuit connected to prevent damage due to an abnormal voltage such as an excessive surge at the analog input pins (AN0 to AN7) and analog power supply (AVCC) should be connected between AVCC and AVSS as shown in figure 13.7. Also, the bypass capacitors connected to AVCC and the filter capacitor connected to AN0 to AN7 must be connected to AVSS.
Rev.2.00 Mar. 22, 2007 Page 435 of 684 REJ09B0352-0200
13. A/D Converter
If a filter capacitor is connected as shown in figure 13.7, the input currents at the analog input pins (AN0 to AN7) are averaged, and so an error may arise. Also, when A/D conversion is performed frequently, as in scan mode, if the current charged and discharged by the capacitance of the sample-and-hold circuit in the A/D converter exceeds the current input via the input impedance (Rin), an error will arise in the analog input pin voltage.Therefore careful consideration is required when deciding the circuit constants.
AVCC
Rin* 2 *1
100 AN0 to AN7 0.1 F AVSS
Notes:
Values are reference values. 1. 10 F 0.01 F
2. Rin: Input impedance
Figure 13.7 Example of Analog Input Protection Circuit
Rev.2.00 Mar. 22, 2007 Page 436 of 684 REJ09B0352-0200
13. A/D Converter
Table 13.5 Analog Pin Specifications
Item Analog input capacitance Permissible signal source impedance Min -- -- Max 20 5 Unit pF k
10 k AN0 to AN7 To A/D converter 20 pF
Note: Values are reference values.
Figure 13.8 Analog Input Pin Equivalent Circuit A/D Conversion Precision Definitions: H8/3022 Group A/D conversion precision definitions are given below. * Resolution The number of A/D converter digital output codes * Offset error The deviation of the analog input voltage value from the ideal A/D conversion characteristic when the digital output changes from the minimum voltage value 0000000000 to 0000000001 (see figure 13.10). * Full-scale error The deviation of the analog input voltage value from the ideal A/D conversion characteristic when the digital output changes from 1111111110 to 1111111111 (see figure 13.10). * Quantization error The deviation inherent in the A/D converter, given by 1/2 LSB (see figure 13.9). * Nonlinearity error The error with respect to the ideal A/D conversion characteristic between the zero voltage and the full-scale voltage. Does not include the offset error, full-scale error, or quantization error.
Rev.2.00 Mar. 22, 2007 Page 437 of 684 REJ09B0352-0200
13. A/D Converter
* Absolute precision The deviation between the digital value and the analog input value. Includes the offset error, full-scale error, quantization error, and nonlinearity error.
Digital output
111 110 101 100 011 010 001 000
Ideal A/D conversion characteristic
Quantization error
1 8
2 8
3 8
4 8
5 8
6 8
7 8
FS
Analog input voltage
Figure 13.9 A/D Conversion Precision Definitions (1)
Rev.2.00 Mar. 22, 2007 Page 438 of 684 REJ09B0352-0200
13. A/D Converter
Full-scale error
Digital output
Ideal A/D conversion characteristic
Nonlinearity error
Actual A/D conversion characteristic FS Offset error Analog input voltage
Figure 13.10 A/D Conversion Precision Definitions (2) Permissible Signal Source Impedance: H8/3022 Group analog input is designed so that conversion precision is guaranteed for an input signal for which the signal source impedance is 5 k or less. This specification is provided to enable the A/D converter's sample-and-hold circuit input capacitance to be charged within the sampling time; if the sensor output impedance exceeds 5 k, charging may be insufficient and it may not be possible to guarantee the A/D conversion precision. When converting in the single mode, if a large capacitance is provided externally, the input load will essentially comprise only the internal input resistance of 10 k, and the signal source impedance is ignored. However, since a low-pass filter effect is obtained in this case, it may not be possible to follow an analog signal with a large differential coefficient (e.g., voltage regulation 5 mV/s or greater). (See figure 13.11.) When converting a high-speed analog signal and when performing conversion in the scan mode, a low-impedance buffer should be inserted.
Rev.2.00 Mar. 22, 2007 Page 439 of 684 REJ09B0352-0200
13. A/D Converter
Influences on Absolute Precision: Adding capacitance results in coupling with GND, and therefore noise in GND may adversely affect absolute precision. Be sure to make the connection to an electrically stable GND such as AVSS. Care is also required to insure that filter circuits do not communicate with digital signals on the mounting board, thus acting as antennas.
H8/3022 Group Sensor output impedance Up to 5 k Sensor input Low-pass filter C to 0.1 F Cin = 15 pF 20 pF
A/D converter equivalent circuit 10 k
Note: Values are reference values.
Figure 13.11 Example of Analog Input Circuit
Rev.2.00 Mar. 22, 2007 Page 440 of 684 REJ09B0352-0200
14. RAM
Section 14 RAM
14.1 Overview
The H8/3022 has 8 kbytes of on-chip static RAM, H8/3021 has 8 kbytes, and H8/3020 has 4kbytes. The RAM is connected to the CPU by a 16-bit data bus. The CPU accesses both byte data and word data in two states, making the RAM suitable for rapid data transfer. The RAM enable bit (RAME) in the system control register (SYSCR) can enable or disable the on-chip RAM. Table 14.1 shows the address of the on-chip RAM in each operating mode. Table 14.1 The Address of the On-Chip RAM in Each Operating Mode
Mode Modes 1, 5, 6, 7 Mode 3 H8/3022 (8 kbytes) H'FDF10 to H'FFF0F H'FFDF10 to H'FFFF0F H8/3021 (8 kbytes) H'FDF10 to H'FFF0F H'FFDF10 to H'FFFF0F H8/3020 (4k byte) H'FEF10 to H'FFF0F H'FFEF10 to H'FFFF0F
Rev.2.00 Mar. 22, 2007 Page 441 of 684 REJ09B0352-0200
14. RAM
14.1.1
Block Diagram
Figure 14.1 shows a block diagram of the on-chip RAM.
Internal data bus (upper 8 bits)
Internal data bus (lower 8 bits)
Bus interface
SYSCR
H'FDF10* H'FDF12*
H'FDF11* H'FDF13*
On-chip RAM H'FFF0E * Even addresses Legend SYSCR: System control register Note: * Lower 20 bits of the address H'FFF0F * Odd addresses
Figure 14.1 RAM Block Diagram (H8/3022 in Modes 1, 5, 6 and 7) 14.1.2 Register Configuration
The on-chip RAM is controlled by the system control register (SYSCR). Table 14.2 gives the address and initial value of SYSCR. Table 14.2 RAM Control Register
Address* H'FFF2 Note: * Name System control register Lower 16 bits of the address Abbreviation SYSCR R/W R/W Initial Value H'0B
Rev.2.00 Mar. 22, 2007 Page 442 of 684 REJ09B0352-0200
14. RAM
14.2
Bit
System Control Register (SYSCR)
7 SSBY 0 R/W 6 STS2 0 R/W 5 STS1 0 R/W 4 STS0 0 R/W 3 UE 1 R/W 2 NMIEG 0 R/W 1 -- 1 -- 0 RAME 1 R/W
Initial value Read/Write
RAM enable bit Enables or disables on-chip RAM Reserved bit NMI edge select User bit enable Standby timer select 2 to 0 Software standby
SYSCR is to enable or disable access to the on-chip RAM. The on-chip RAM is enabled or disabled by the RAME bit in SYSCR. For details about the other bits, see section 3.3, System Control Register. Bit 0--RAM Enable (RAME): Enables or disables the on-chip RAM. The RAME bit is initialized at the rising edge of the input at the RES pin. It is not initialized in software standby mode.
Bit 0 RAME 0 1 Description On-chip RAM is disabled On-chip RAM is enabled (Initial value)
Rev.2.00 Mar. 22, 2007 Page 443 of 684 REJ09B0352-0200
14. RAM
14.3
Operation
When the RAME bit is set to 1, the on-chip RAM is enabled. This LSI can access the on-chip RAM when addressing the addresses shown in Table 14.1 in each operation mode. When the RAME bit is cleared to 0 in modes 1, 3, 5, and 6 (expanded modes), external address space is accessed. When the RAME bit is cleared to 0 in mode 7 (single-chip modes), the on-chip RAM is not accessed. Read operation always reads H'FF and disables writing. The on-chip RAM is connected to the CPU by a 16-bit wide data bus and can be read and written on a byte or a word basis. Byte data can be accessed in two states using the higher 8 bits of the data bus. Word data beginning from an even address can be accessed in two states using the 16-bit data bus.
Rev.2.00 Mar. 22, 2007 Page 444 of 684 REJ09B0352-0200
15. ROM
Section 15 ROM
15.1 Features
The H8/3022 Group has 256 kbytes of on-chip flash memory. The features of the flash memory are summarized below. * Four flash memory operating modes Program mode Erase mode Program-verify mode Erase-verify mode * Programming/erase methods The flash memory is programmed 128 bytes at a time. Block erase (in single-block units) can be performed. To erase the entire flash memory, each block must be erased in turn. Block erasing can be performed as required on 4 kbytes, 32 kbytes, and 64 kbytes blocks. * Programming/erase times The flash memory programming time is 10 ms (typ.) for simultaneous 128-byte programming, equivalent to about 80 s (typ.) per byte, and the erase time is 100 ms (typ.). * Reprogramming capability The flash memory can be reprogrammed up to 100 times. * On-board programming modes There are two modes in which flash memory can be programmed/erased/verified on-board: Boot mode User program mode * Automatic bit rate adjustment With data transfer in boot mode, the LSI's bit rate can be automatically adjusted to match the transfer bit rate of the host. * Flash memory emulation in RAM Flash memory programming can be emulated in real time by overlapping a part of RAM onto flash memory. * Protect modes There are two protect modes, hardware and software, which allow protected status to be designated for flash memory program/erase/verify operations. * PROM mode Flash memory can be programmed/erased in programmer mode, using a PROM programmer, as well as in on-board PROM mode.
Rev.2.00 Mar. 22, 2007 Page 445 of 684 REJ09B0352-0200
15. ROM
15.2
15.2.1
Overview
Block Diagram
Internal address bus
Internal data bus (16 bits)
Module bus
2 FLMCR1 * 2 FLMCR2 *
EBR1 EBR2 RAMER
*2 *2 *2
Bus interface/controller
Operating mode
*1 FWE pin Mode pin
Flash memory (256 kbytes)
Legend FLMCR1: FLMCR2: EBR1: EBR2: RAMER:
Flash memory control register 1 Flash memory control register 2 Erase block register 1 Erase block register 2 RAM emulation register
Notes: 1. Functions as the FWE pin in the flash memory version, and as the RESO pin in the mask ROM version. 2. The registers that control the flash memory (FLMCR1, FLMCR2, EBR1, EBR2, and RAMER) are for use exclusively by the flash memory version, and are not provided in the mask ROM version. Reads to the corresponding addresses in the mask ROM version will always return 1, and writes to these addresses are invalid.
Figure 15.1 Block Diagram of Flash Memory
Rev.2.00 Mar. 22, 2007 Page 446 of 684 REJ09B0352-0200
15. ROM
15.2.2
Mode Transitions
When the mode pins and the FWE pin are set in the reset state and a reset-start is executed, the microcomputer enters an operating mode as shown in figure 15.2. In user mode, flash memory can be read but not programmed or erased. The boot, user program and PROM modes are provided as modes to write and erase the flash memory.
*1 User mode
*5 RES = 0
Reset state
RES = 0 *4 RES = 0 *3 RES = 0
PROM mode
*2
*4
FWE = 0
User program mode
*1
Boot mode On-board programming mode
Notes: Only make a transition between user mode and user program mode when the CPU is not accessing the flash memory. 1. RAM emulation possible 2. The H8/3022F is placed in PROM mode by means of a dedicated PROM programmer. 3. MD2, MD1, MD0 = (0, 0, 1) (0, 1, 0) (0, 1, 1) FWE = 1 4. MD2, MD1, MD0 = (1, 0, 1) (1, 1, 0) (1, 1, 1) FWE = 1 5. MD2, MD1, MD0 = (1, 0, 1) (1, 1, 0) (1, 1, 1) FWE = 0
Figure 15.2 Flash Memory State Transitions
Rev.2.00 Mar. 22, 2007 Page 447 of 684 REJ09B0352-0200
15. ROM
State transitions between the normal and user modes and on-board program mode are performed by changing the FWE pin level from high to low or from low to high. To prevent misoperation (erroneous programming or erasing) in these cases, the bits in the flash memory control register 1 (FLMCR1) should be cleared to 0 before making such a transition. After the bits are cleared, a wait time is necessary. Normal operation is not guaranteed if this wait time is insufficient.
Rev.2.00 Mar. 22, 2007 Page 448 of 684 REJ09B0352-0200
15. ROM
15.2.3
On-Board Programming Modes
Boot Mode (Example)
1. Initial state The old program version or data remains written in the flash memory. The user should prepare the programming control program and new application program beforehand in the host. 2. Programming control program transfer When boot mode is entered, the boot program in the H8/3022 (originally incorporated in the chip) is started and the programming control program in the host is transferred to RAM via SCI communication. The boot program required for flash memory erasing is automatically transferred to the RAM boot program area.
Host
Host Programming control program New application program
New application program
H8/3022
Boot program Flash memory RAM SCI
H8/3022
Boot program Flash memory RAM Boot program area SCI
Application program (old version)
Application program (old version)
Programming control program
3. Flash memory initialization The erase program in the boot program area (in RAM) is executed, and the flash memory is initialized (to H'FF). In boot mode, total flash memory erasure is performed, without regard to blocks.
Host
4. Writing new application program The programming control program transferred from the host to RAM is executed, and the new application program in the host is written into the flash memory.
Host
New application program
H8/3022
Boot program Flash memory RAM Boot program area Flash memory preprogramming erase
Programming control program
H8/3022
SCI Boot program Flash memory RAM Boot program area New application program
Programming control program
SCI
Program execution state
Rev.2.00 Mar. 22, 2007 Page 449 of 684 REJ09B0352-0200
15. ROM
User Program Mode (Example)
1. Initial state The FWE assessment program that confirms that user program mode has been entered, and the program that will transfer the programming/erase control program from flash memory to on-chip RAM should be written into the flash memory by the user beforehand. The programming/erase control program should be prepared in the host or in the flash memory.
Host Programming/ erase control program New application program New application program
2. Programming/erase control program transfer When user program mode is entered, user software confirms this fact, executes transfer program in the flash memory, and transfers the programming/erase control program to RAM.
Host
H8/3022
Boot program Flash memory
FWE assessment program
H8/3022
SCI RAM Boot program Flash memory
FWE assessment program
SCI RAM
Transfer program
Transfer program
Programming/ erase control program
Application program (old version)
Application program (old version)
3. Flash memory initialization The programming/erase program in RAM is executed, and the flash memory is initialized (to H'FF). Erasing can be performed in block units, but not in byte units.
Host
4. Writing new application program Next, the new application program in the host is written into the erased flash memory blocks. Do not write to unerased blocks.
Host
New application program
H8/3022
Boot program Flash memory
FWE assessment program
H8/3022
SCI RAM Boot program Flash memory
FWE assessment program Transfer program Programming/ erase control program Programming/ erase control program
SCI RAM
Transfer program
Flash memory erase
New application program
Program execution state
Rev.2.00 Mar. 22, 2007 Page 450 of 684 REJ09B0352-0200
15. ROM
15.2.4
Flash Memory Emulation in RAM
In the H8/3022F, flash memory programming can be emulated in real time by overlapping the flash memory with part of RAM (overlap RAM). When the emulation block set in RAMER is accessed while the emulation function is being executed, data written in the overlap RAM is read. Emulation should be performed in user mode or user program mode.
SCI
Flash memory Emulation block
RAM
Overlap RAM (emulation is performed on data written in RAM) Application program Execution state
Figure 15.3 Reading Overlap RAM Data in User Mode or User Program Mode When overlap RAM data is confirmed, the RAMS bit is cleared, RAM overlap is released, and writes should actually be performed to the flash memory. However, in on-board programming mode, when the programming control program is transferred to RAM, ensure that the transfer destination and the overlap RAM do not overlap, as this will cause data in the overlap RAM to be rewritten.
Rev.2.00 Mar. 22, 2007 Page 451 of 684 REJ09B0352-0200
15. ROM
SCI
Flash memory Programming data
RAM
Application program
Overlap RAM (programming data) Programming control program execution state
Figure 15.4 Writing Overlap RAM Data in User Program Mode 15.2.5 Differences between Boot Mode and User Program Mode
Boot Mode Total erase Block erase Programming control program* Yes No Boot program is initiated, and programming control program is transferred from host to on-chip RAM, and executed there. User Program Mode Yes Yes Program that controls programming program in flash memory is executed. Program should be written beforehand in PROM mode and boot program mode.
Note:
*
To be provided by the user, in accordance with the recommended algorithm.
Rev.2.00 Mar. 22, 2007 Page 452 of 684 REJ09B0352-0200
15. ROM
15.2.6
Block Configuration
The flash memory is divided into three 64 kbytes blocks, one 32 kbytes block, and eight 4 kbytes blocks. Erasing can be carried out using these block units.
Address H'00000 4 kbytes x 8 32 kbytes
64 kbytes
256 kbytes 64 kbytes
64 kbytes Address H'3FFFF
Figure 15.5 Block Configuration
Rev.2.00 Mar. 22, 2007 Page 453 of 684 REJ09B0352-0200
15. ROM
15.3
Pin Configuration
The flash memory is controlled by means of the pins shown in table 15.1. Table 15.1 Pin Configuration
Pin Name Reset Flash write enable Mode 2 Mode 1 Mode 0 Transmit data Receive data Abbreviation RES FWE MD2 MD1 MD0 TxD1 RxD1 I/O Input Input Input Input Input Output Input Function Reset Flash program/erase protection by hardware Sets LSI operating mode Sets LSI operating mode Sets LSI operating mode Serial transmit data output Serial receive data input
15.4
Register Configuration
1
The registers* used to control the on-chip flash memory when enabled are shown in table 15.2. Table 15.2 Register Configuration
Register Name Flash memory control register 1 Flash memory control register 2 Erase block register 1 Erase block register 2 RAM emulation register Abbreviation FLMCR1* FLMCR2* EBR1* EBR2*
1 1 1 1 1
R/W R/W R R/W R/W R/W
Initial Value H'00* H'00 H'00 H'00 H'F0
3
Address* H'FF40 H'FF41 H'FF42 H'FF43 H'FF47
2
RAMER*
Notes: 1. FLMCR1, FLMCR2, EBR1, and EBR2, and RAMER are 8-bit registers. Byte access must be used on these registers (do not use word or longword access). These registers are for use exclusively by the flash memory version, and are not provided in the mask ROM version. Reads to the corresponding addresses in the mask ROM version will always return 1, and writes to these addresses are invalid. Access to address H'FF44 to H'FF46 and H'FF48 to H'FF4F (lower 16 bits) is prohibited. 2. Lower 16 bits of the address. 3. When a high level is input to the FWE pin, the initial value is H'80.
Rev.2.00 Mar. 22, 2007 Page 454 of 684 REJ09B0352-0200
15. ROM
15.5
15.5.1
Register Descriptions
Flash Memory Control Register 1 (FLMCR1)
FLMCR1 is an 8-bit register used for flash memory operating mode control. Program-verify mode or erase-verify mode is entered by setting SWE bit to 1 when FWE = 1, then setting the PV or EV bit. Program mode is entered by setting SWE1 bit to 1 when FWE = 1, then setting the PSU bit, and finally setting the P bit. Erase mode is entered by setting SWE bit to 1 when FWE = 1, then setting the ESU bit, and finally setting the E bit. FLMCR1 is initialized by a power-on reset, and in hardware standby mode and software standby mode. Its initial value is H'80 when a high level is input to the FWE pin, and H'00 when a low level is input. When on-chip flash memory is disabled, a read will return H'00, and writes are invalid. Writes are enabled only in the following cases: Writes to bit SWE of FLMCR1 enabled when FWE = 1, to bits ESU, PSU, EV, and PV when FWE = 1 and SWE = 1, to bit E when FWE = 1, SWE = 1 and ESU = 1, and to bit P when FWE = 1, SWE = 1, and PSU = 1. Notes: 1. To prevent erroneous programming or erasing, the setting of individual bits in this register must be carried out in accordance with the programming and erase flowcharts. 2. Transitions are made to program mode, erase mode, program-verify mode, and eraseverify mode according to the settings in this register. When reading flash memory as normal on-chip ROM, bits 6 to 0 in this register must be cleared.
Bit: 7 FWE Initial value: R/W: Note: * --* R 6 SWE 0 R/W 5 ESU 0 R/W 4 PSU 0 R/W 3 EV 0 R/W 2 PV 0 R/W 1 E 0 R/W 0 P 0 R/W
Set according to the state of the FWE pin.
Bit 7--Flash Write Enable Bit (FWE): Sets hardware protection against flash memory programming/erasing.
Bit 7 FWE 0 1 Description When a low level is input to the FWE pin (hardware-protected state) When a high level is input to the FWE pin
Rev.2.00 Mar. 22, 2007 Page 455 of 684 REJ09B0352-0200
15. ROM
Bit 6--Software Write Enable Bit (SWE): Enables or disables flash memory programming and erasing. Set this bit when setting bits 5 to 0, bits 7 to 0 of EBR1, and bits 3 to 0 of EBR2.
Bit 6 SWE 0 1 Description Writes disabled Writes enabled [Setting condition] When FWE = 1 Note: Do not execute a SLEEP instruction while the SWE bit is set to 1. (Initial value)
Bit 5--Erase Setup Bit (ESU): Prepares for a transition to erase mode. Do not set the SWE, PSU, EV, PV, E, or P bit at the same time.
Bit 5 ESU 0 1 Description Erase setup cleared Erase setup [Setting condition] When FWE = 1 and SWE = 1 (Initial value)
Bit 4--Program Setup Bit (PSU): Prepares for a transition to program mode. Do not set the SWE, ESU, EV, PV, E, or P bit at the same time.
Bit 4 PSU 0 1 Description Program setup cleared Program setup [Setting condition] When FWE = 1 and SWE = 1 (Initial value)
Rev.2.00 Mar. 22, 2007 Page 456 of 684 REJ09B0352-0200
15. ROM
Bit 3--Erase-Verify (EV): Selects erase-verify mode transition or clearing. Do not set the SWE, ESU, PSU, PV, E, or P bit at the same time.
Bit 3 EV 0 1 Description Erase-verify mode cleared Transition to erase-verify mode [Setting condition] When FWE = 1 and SWE = 1 (Initial value)
Bit 2--Program-Verify (PV): Selects program-verify mode transition or clearing. Do not set the SWE, ESU, PSU, EV, E, or P bit at the same time.
Bit 2 PV 0 1 Description Program-verify mode cleared Transition to program-verify mode [Setting condition] When FWE = 1 and SWE = 1 (Initial value)
Bit 1--Erase (E): Selects erase mode transition or clearing. Do not set the SWE, ESU, PSU, EV, PV, or P bit at the same time.
Bit 1 E 0 1 Description Erase mode cleared Transition to erase mode* [Setting condition] When FWE = 1, SWE = 1, and ESU = 1 Note: * Do not access flash memory while the E bit is set to 1. (Initial value)
Rev.2.00 Mar. 22, 2007 Page 457 of 684 REJ09B0352-0200
15. ROM
Bit 0--Program (P): Selects program mode transition or clearing. Do not set the SWE, PSU, ESU, EV, PV, or E bit at the same time.
Bit 0 P 0 1 Description Program mode cleared Transition to program mode* [Setting condition] When FWE = 1, SWE = 1, and PSU = 1 Note: * Do not access flash memory while the P bit is set to 1. (Initial value)
15.5.2
Flash Memory Control Register 2 (FLMCR2)
FLMCR2 is an 8-bit register used for flash memory operating mode control. FLMCR2 is initialized to H'00 by a power-on reset, and in hardware standby mode and software standby mode. When on-chip flash memory is disabled, a read will return H'00. Note: FLMCR2 is a read-only register; it must not be written to.
Bit: 7 FLER Initial value: R/W: 0 R 6 -- 0 R 5 -- 0 R 4 -- 0 R 3 -- 0 R 2 -- 0 R 1 -- 0 R 0 -- 0 R
Bit 7--Flash Memory Error (FLER): Indicates that an error has occurred during an operation on flash memory (programming or erasing). When FLER is set to 1, flash memory goes to the errorprotection state.
Rev.2.00 Mar. 22, 2007 Page 458 of 684 REJ09B0352-0200
15. ROM Bit 7 FLER 0
Description Flash memory is operating normally [Clearing condition] RES pin reset, WDT reset, or hardware standby mode (Initial value) Flash memory program/erase protection (error protection) is disabled
1
An error has occurred during flash memory programming/erasing Flash memory program/erase protection (error protection) is enabled [Setting condition] * When flash memory is read* during programming/erasing (including a vector read or instruction fetch, but excluding reads in a RAM area overlapping flash memory space) Immediately after the start of exception handling during programming/erasing (but excluding reset, illegal instruction, trap instruction, and division-by-zero exception handling) When a SLEEP instruction (including software standby) is executed during programming/erasing
2
*
*
Bits 6 to 0--Reserved: Only 0 may be written to these bits. 15.5.3 Erase Block Register 1 (EBR1)
EBR1 is an 8-bit register that specifies the flash memory erase area block by block. EBR1 is initialized to H'00 by a power-on reset, in hardware standby mode and software standby mode, when a low level is input to the FWE pin, and when a high level is input to the FWE pin and the SWE bit in FLMCR1 is not set. When a bit in EBR1 is set to 1, the corresponding block can be erased. Other blocks are erase-protected. Only one of the bits of EBR1 and EBR2 combined can be set. Do not set more than one bit, as this will cause all the bits in both EBR1 and EBR2 to be automatically cleared to 0. When on-chip flash memory is disabled, a read will return H'00, and writes are invalid.
Rev.2.00 Mar. 22, 2007 Page 459 of 684 REJ09B0352-0200
15. ROM
The flash memory block configuration is shown in table 15.3. A total memory erase is carried out by erasing individual blocks in turn.
Bit: Initial value: R/W: 7 EB7 0 R/W 6 EB6 0 R/W 5 EB5 0 R/W 4 EB4 0 R/W 3 EB3 0 R/W 2 EB2 0 R/W 1 EB1 0 R/W 0 EB0 0 R/W
15.5.4
Erase Block Register 2 (EBR2)
EBR2 is an 8-bit register that specifies the flash memory erase area block by block. EBR2 is initialized to H'00 by a power-on reset, in hardware standby mode and software standby mode, when a low level is input to the FWE pin. Bit 0 will be initialized to 0 if bit SWE of FLMCR1 is not set, even though a high level is input to pin FWE. When a bit in EBR2 is set to 1, the corresponding block can be erased. Other blocks are erase-protected. Only one of the bits of EBR1 and EBR2 combined can be set. Do not set more than one bit, as this will cause all the bits in both EBR1 and EBR2 to be automatically cleared to 0. Bits 7 to 4 are reserved and must only be written with 0. When on-chip flash memory is disabled, a read will return H'00, and writes are invalid. The flash memory block configuration is shown in table 15.3. A total memory erase is carried out by erasing individual blocks in turn. Note: Bits 7 to 4 in this register must not be set to 1. If bits 7 to 4 are set when an EBR1/EBR2 bit is set, EBR1/EBR2 will be initialized to H'00.
Bit: 7 -- Initial value: R/W: 0 R/W 6 -- 0 R/W 5 -- 0 R/W 4 -- 0 R/W 3 EB11 0 R/W 2 EB10 0 R/W 1 EB9 0 R/W 0 EB8 0 R/W
Rev.2.00 Mar. 22, 2007 Page 460 of 684 REJ09B0352-0200
15. ROM
Table 15.3 Flash Memory Erase Blocks
Block (Size) EB0 (4 kB) EB1 (4 kB) EB2 (4 kB) EB3 (4 kB) EB4 (4 kB) EB5 (4 kB) EB6 (4 kB) EB7 (4 kB) EB8 (32 kB) EB9 (64 kB) EB10 (64 kB) EB11 (64 kB) Addresses H'000000-H'000FFF H'001000-H'001FFF H'002000-H'002FFF H'003000-H'003FFF H'004000-H'004FFF H'005000-H'005FFF H'006000-H'006FFF H'007000-H'007FFF H'008000-H'00FFFF H'010000-H'01FFFF H'020000-H'02FFFF H'030000-H'03FFFF
15.5.5
RAM Emulation Register (RAMER)
RAMER specifies the area of flash memory to be overlapped with part of RAM when emulating real-time flash memory programming. RAMER initialized to H'F0 by a power-on reset and in hardware standby mode. It is not initialized in software standby mode. RAMER settings should be made in user mode or user program mode. Flash memory area divisions are shown in table 15.4. To ensure correct operation of the emulation function, the ROM for which RAM emulation is performed should not be accessed immediately after this register has been modified. Normal execution of an access immediately after register modification is not guaranteed.
Bit: 7 -- Initial value: R/W: 1 R 6 -- 1 R 5 -- 1 R 4 -- 1 R 3 RAMS 0 R/W 2 RAM2 0 R/W 1 RAM1 0 R/W 0 RAM0 0 R/W
Bits 7 to 4--Reserved: These bits always read 1.
Rev.2.00 Mar. 22, 2007 Page 461 of 684 REJ09B0352-0200
15. ROM
Bit 3--RAM Select (RAMS): Specifies selection or non-selection of flash memory emulation in RAM. When RAMS = 1, all flash memory block are program/erase-protected.
Bit 3 RAMS 0 1 Description Emulation not selected Program/erase-protection of all flash memory blocks is disabled Emulation selected Program/erase-protection of all flash memory blocks is enabled (Initial value)
Bits 2 to 0--Flash Memory Area Selection: These bits are used together with bit 3 to select the flash memory area to be overlapped with RAM. (See table 15.4.) Table 15.4 Flash Memory Area Divisions
Addresses H'FFFFE000-H'FFFFEFFF H'00000000-H'00000FFF H'00001000-H'00001FFF H'00002000-H'00002FFF H'00003000-H'00003FFF H'00004000-H'00004FFF H'00005000-H'00005FFF H'00006000-H'00006FFF H'00007000-H'00007FFF Block Name RAM area 4 kbytes EB0 (4 kbytes) EB1 (4 kbytes) EB2 (4 kbytes) EB3 (4 kbytes) EB4 (4 kbytes) EB5 (4 kbytes) EB6 (4 kbytes) EB7 (4 kbytes) RAMS 0 1 1 1 1 1 1 1 1 RAM2 * 0 0 0 0 1 1 1 1 RAM1 * 0 0 1 1 0 0 1 1 RAM0 * 0 1 0 1 0 1 0 1
*: Don't care Note: When performing flash memory emulation by RAM, the RAME bit in SYSCR must be set to 1.
Rev.2.00 Mar. 22, 2007 Page 462 of 684 REJ09B0352-0200
15. ROM
15.5.6
Differences from H8/3039 F-ZTAT Group
Table 15.5 Comparison of H8/3039F and H8/3022F
H8/3039F Size Program/erase voltage Programming Programming unit Write pulse application method Erasing Block configuration EBR configuration 128 kbytes Supplied from VCC 32-byte simultaneous programming 150 s x 4 + 500 s x 399 H8/3022F 256 kbytes Supplied from VCC 128-byte simultaneous programming 30 s x 6 + 200 s x 994 (with 10 s additional 1 programming)* 12 blocks 4 kbytes x 8, 32 kbytes x 1, 64 kbytes x 3 EBR1: H'FF42
3 EB3 2 EB2 1 EB1 0 EB0 7 EB7 6 EB6 5 EB5 4 EB4 3 EB3 2 EB2 1 EB1 0 EB0
8 blocks 1 kbyte x 4, 28 kbytes x 1, 32 kbytes x 3 EBR: H'FF42
7 EB7 6 EB6 5 EB5 4 EB4
EBR2: H'FF43
7 -- 6 -- 5 -- 4 -- 3 2 1 0 EB8 EB11 EB10 EB9
RAM emulation
RAM area Applicable blocks RAMCR configuration
1 kbyte (H'FF800 to H'FFBFF) EB0 to EB3 RAMCR: H'FF47
7 -- 6 -- 5 -- 4 -- 3 2 1 0 -- RAMS RAM2 RAM1
4 kbytes (H'FE000 to H'FEFFF) EB0 to EB7 RAMER: H'FF47
7 -- 6 -- 5 -- 4 -- 3 2 1 0 RAMS RAM2 RAM1 RAM0
Flash error
FLER bit
FLMSR: H'FF4D
7 FLER 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 --
FLMCR2: H'FF41
7 FLER 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 --
Flash memory Wait after SWE -- characteristics clearing Boot mode Bit rate Boot area User area 9,600 bps, 4,800 bps H'FEF10 to H'FF2FF H'FF300 to H'FFF0F
tCSWE specification must be 2 met* 19,200 bps, 9,600 bps, 4,800 bps H'FFDF10 to H'FFE70F H'FFE710 to H'FFFF0F
Rev.2.00 Mar. 22, 2007 Page 463 of 684 REJ09B0352-0200
15. ROM H8/3039F PROM mode Use of PROM programmer supporting Renesas Technology microcomputer device type with 128 kbytes on-chip flash memory (FZTAT128) H8/3022F Use of PROM programmer supporting Renesas Technology microcomputer device type with 256 kbytes on-chip flash memory (FZTAT256)
Notes: 1. See section 15.7, Programming/Erasing Flash Memory, for details of the H8/3022F program/erase algorithms. 2. See section 18.2.5, Flash Memory Characteristics, for details of the H8/3022F flash memory characteristics.
15.6
On-Board Programming Modes
When pins are set to on-board programming mode and a reset-start is executed, a transition is made to the on-board programming state in which program/erase/verify operations can be performed on the on-chip flash memory. There are two on-board programming modes: boot mode and user program mode. The pin settings for transition to each of these modes are shown in table 15.6. For a diagram of the transitions to the various flash memory modes, see figure 15.2. Table 15.6 Setting On-Board Programming Modes
Mode Boot mode Expanded modes Mode 5 Mode 6 Single-chip mode User program mode Expanded modes Mode 7 Mode 5 Mode 6 Single-chip mode Mode 7 1 FWE 1*
1
MD2 0* 0* 0* 1 1 1
2 2 2
MD1 0 1 1 0 1 1
MD0 1 0 1 1 0 1
Notes: 1. For the high-level application timing, see items (6) and (7) in Notes on Use of Boot Mode. 2. In boot mode, the MD2 setting should be the inverse of the input (0). In boot mode, the mode control register (MDCR) can be used to monitor the status of modes 5, 6, and 7, in the same way as in normal mode.
Rev.2.00 Mar. 22, 2007 Page 464 of 684 REJ09B0352-0200
15. ROM
15.6.1
Boot Mode
When boot mode is used, the flash memory programming control program must be prepared in the host beforehand. The SCI channel to be used is set to asynchronous mode. When a reset-start is executed after the LSI's pins have been set to boot mode, the boot program built into the LSI is started and the programming control program prepared in the host is serially transmitted to the LSI via the SCI. In the LSI, the programming control program received via the SCI is written into the programming control program area in on-chip RAM. After the transfer is completed, control branches to the start address (in mode 6, H'FFE710) of the user program area and the programming control program execution state is entered (flash memory programming is performed). The transferred programming control program must therefore include coding that follows the programming algorithm given later. The system configuration in boot mode is shown in figure 15.6, and the boot mode execution procedure in figure 15.7.
LSI
Flash memory
Host
Write data reception Verify data transmission
RXD1 SCI1 TXD1
On-chip RAM
Figure 15.6 System Configuration in Boot Mode
Rev.2.00 Mar. 22, 2007 Page 465 of 684 REJ09B0352-0200
15. ROM
Start Set pins to boot program mode and execute reset-start Host transfers data (H'00) continuously at prescribed bit rate H8/3022F measures low period of H'00 data transmitted by host H8/3022F calculates bit rate and sets value in bit rate register After bit rate adjustment, H8/3022F transmits one H'00 data byte to host to indicate end of adjustment Host confirms normal reception of bit rate adjustment end indication (H'00), and transmits one H'55 data byte After receiving H'55, H8/3022F transmits one H'AA data byte to host Host transmits number of programming control program bytes (N), upper byte followed by lower byte H8/3022F transmits received number of bytes to host as verify data (echo-back) n=1
Host transmits programming control program sequentially in byte units H8/3022F transmits received programming control program to host as verify data (echo-back) Transfer received programming control program to on-chip RAM n = N? Yes End of transmission Check flash memory data, and if data has already been written, erase all blocks After confirming that all flash memory data has been erased, H8/3022F transmits one H'AA data byte to host Execute programming control program transferred to on-chip RAM Note: If a memory cell malfunctions and cannot be erased, the H8/3022F sends one H'FF byte as an erase error, and stops the erase operation and subsequent operations. No n+1n
Figure 15.7 Boot Mode Execution Procedure
Rev.2.00 Mar. 22, 2007 Page 466 of 684 REJ09B0352-0200
15. ROM
Automatic SCI Bit Rate Adjustment
Start bit D0 D1 D2 D3 D4 D5 D6 D7 Stop bit
Low period (9 bits) measured (H'00 data)
High period (1 or more bits)
When boot mode is initiated, the LSI measures the low period of the asynchronous SCI communication data (H'00) transmitted continuously from the host. The SCI transmit/receive format should be set as follows: 8-bit data, 1 stop bit, no parity. The LSI calculates the bit rate of the transmission from the host from the measured low period, and transmits one H'00 byte to the host to indicate the end of bit rate adjustment. The host should confirm that this adjustment end indication (H'00) has been received normally, and transmit one H'55 byte to the LSI. If reception cannot be performed normally, initiate boot mode again (reset), and repeat the above operations. Depending on the host's transmission bit rate and the LSI's system clock frequency, there will be a discrepancy between the bit rates of the host and the LSI. Set the host transfer bit rate at 4,800, 1 9,600 or 19,200 bps* to operate the SCI properly. Table 15.7 shows host transfer bit rates and system clock frequencies for which automatic adjustment of the LSI bit rate is possible. The boot program should be executed within this system 2 clock range.* Table 15.7 System Clock Frequencies for which Automatic Adjustment of LSI Bit Rate is Possible
Host Bit Rate 4,800 bps 9,600 bps 19,200 bps System Clock Frequency for Which Automatic Adjustment of LSI Bit Rate is Possible (MHz) 4 to 18 8 to 18 16 to 18
Notes: 1. Use a host bit rate setting of 4800, 9600, or 19200 bps only. No other setting should be used. 2. Although the H8/3022 may also perform automatic bit rate adjustment with bit rate and system clock combinations other than those shown in table 15.7, a degree of error will arise between the bit rates of the host and the H8/3022, and subsequent transfer will not be performed normally. Therefore, only combinations of bit rate and system clock within the ranges shown in table 15.7 can be used for boot mode execution.
Rev.2.00 Mar. 22, 2007 Page 467 of 684 REJ09B0352-0200
15. ROM
On-Chip RAM Area Divisions in Boot Mode: In boot mode, the RAM area is divided into an area used by the boot program and an area to which the programming control program is transferred via the SCI, as shown in figure 15.8. The boot program area cannot be used until the execution state in boot mode switches to the programming control program transferred from the host.
H'FFDF10 Boot program area H'FFE710 Programming control program area
H'FFFF0F
Note: The boot program area cannot be used until the programming control program transferred to RAM switches to the execution state. Note also that the boot program remains in this area in RAM even after control branches to the programming control program.
Figure 15.8 RAM Areas in Boot Mode (Mode 6) Notes on Use of Boot Mode 1. When the H8/3022 comes out of reset in boot mode, it measures the low period of the input at the SCI's RXD1 pin. The reset should end with RXD1 high. After the reset ends, it takes about 100 states for the H8/3022 to get ready to measure the low period of the RXD1 input. 2. In boot mode, if any data has been programmed into the flash memory (if all data is not H'FF), all flash memory blocks are erased. Boot mode is for use when user program mode is unavailable, such as the first time on-board programming is performed, or if the program activated in user program mode is accidentally erased. 3. Interrupts cannot be used while the flash memory is being programmed or erased. 4. The RXD1 and TXD1 lines should be pulled up on the board. 5. Before branching to the programming control program (in mode 6, H'FFE710 in the RAM area), the H8/3022 terminates transmit and receive operations by the on-chip SCI (channel 1) (by clearing the RE and TE bits to 0 in the serial control register (SCR)), but the adjusted bit
Rev.2.00 Mar. 22, 2007 Page 468 of 684 REJ09B0352-0200
15. ROM
rate value remains set in the bit rate register (BRR). The transmit data output pin, TXD1 , goes to the high-level output state (P91DDR = 1 in P9DDR, P91DR = 1 in P9DR). The contents of the CPU's internal general registers are undefined at this time, so these registers must be initialized immediately after branching to the user program. In particular, since the stack pointer (SP) is used implicitly in subroutine calls, etc., a stack area must be specified for use by the user program. The initial values of other on-chip registers are not changed. 6. Boot mode can be entered by setting pins MD0 to MD2 and FWE in accordance with the mode setting conditions shown in table 15.6, and then executing a reset-start. On reset release (a low-to-high transition)* , the H8/3022 latches the current mode pin states internally and maintains the boot mode state. Boot mode can be cleared by driving the FWE 1 pin low during the reset, then executing reset release* , but the following points must be noted. a. When switching from boot mode to normal mode, the boot mode state within the chip must first be cleared by reset input via the RES pin. The RES pin must be held low for at least 3 20 system clock cycles.* b. Do not change the input levels of the mode pins (MD2 to MD0) or the FWE pin in boot mode. To change the mode, the RES pin must first be driven low to set the reset start. Also, if a watchdog timer reset occurs in the boot mode state, the MCU's internal state will not be cleared, and the on-chip boot program will be restarted regardless of the mode pin states. c. Do not drive the FWE pin low during boot program execution or flash memory 2 programming/erasing* . 7. If the mode pin and FWE pin input levels are changed from 0 V to VCC or from VCC to 0V during a reset (while a low level is being input to the RES pin), the MCU's operating mode will change. As a result, the state of ports with multiplexed address functions and bus control output signals (AS, RD, WR) may also change. Therefore, care must be taken to make pin settings to prevent these pins from becoming output signal pins during a reset, or to prevent collision with signals outside the MCU. Notes: 1. Mode pin and FWE pin input must satisfy the mode programming setup time (tMDS) with respect to the reset release timing. 2. For further information on FWE application and disconnection, see section 15.11, Flash Memory Programming and Erasing Precautions. 3. See section 4.2.2, Reset Sequence, and section 15.11, Flash Memory Programming and Erasing Precautions. The reset period during operation is a minimum of 10 system clock cycles for the H8/3022, H8/3021, and H8/3020 mask ROM versions, but a minimum of 20 system clock cycles for the H8/3022 flash memory version.
1
Rev.2.00 Mar. 22, 2007 Page 469 of 684 REJ09B0352-0200
15. ROM
15.6.2
User Program Mode
When set to the user program mode, this LSI can erase and program its flash memory by executing a user program. Therefore, on-chip flash memory on-board programming can be performed by providing a means of controlling FWE and supplying the write data on the board and providing a write program in a part of the program area. To select this mode, set the LSI to on-chip ROM enable modes 5, 6, and 7 and apply a high level to the FWE pin. In this mode, the peripheral functions, other than flash memory, are performed the same as in modes 5, 6, and 7. Since the flash memory cannot be read while it is being programmed/erased, place a programming program on external memory, or transfer the programming program to RAM area, and execute it in the RAM. Figure 15.9 shows the procedure for executing when transferred to on-chip RAM. During reset start, starting from the user program mode is possible.
Rev.2.00 Mar. 22, 2007 Page 470 of 684 REJ09B0352-0200
15. ROM
The user writes a program that executes steps 3 to 8 in advance as shown below . 1 2 Reset start 2 Sets the mode pin to an on-chip ROM enable mode (mode 5, 6, or 7). Starts the CPU via reset. (The CPU can also be started from the user program mode by setting the FWE pin to High level during reset; that is, during the period the RES pin is a low level.*1) Transfers the on-board programming program to RAM. Branches to the program in RAM. Sets the FWE pin to a high level. *2 (Switches to user program mode.) After confirming that the FWE pin is a high level, executes the on-board programming program in RAM. This reprograms the user application program in flash memory. At the end of reprograming, clears the SWE bit, and exits the user program mode by switching the FWE pin from a high level to a low level. *3 Branches to, and executes, the user application program reprogrammed in flash memory.
1
MD2 to MD0 = 101, 110, 111
3
Transfer on-board programming program to RAM. 3 4
4
Branch to program in RAM. 5 6
5
FWE=high (user program mode) 7
6
Execute on-board programming program in RAM (flash memory reprogramming).
8
7
Input low level to FWE after SWE bit clear (user program mode exit)
8
Execute user application program in flash memory.
Notes: 1. Normally do not apply a high level to the FWE pin. To prevent erroneous programming or erasing in the event of program runaway, etc., apply a high level to the FWE pin only when programming/erasing flash memory (including flash memory emulation by RAM). If program runaway, etc. causes overprogramming or overerasing of flash memory, the memory cells will not operate normally. Also, while a high level is applied to the FWE pin, the watchdog timer should be activated to prevent overprogramming or overerasing due to program runaway, etc. 2. For notes on FWE pin High/Low, see section 15.11, Notes on Flash Memory Programming/Erasing. 3. In order to execute a normal read of flash memory in user program mode, the program/erase program must not be executing. It is thus necessary to ensure that bits 6 to 0 in FLMCR1 are cleared to 0.
Figure 15.9 User Program Mode Execution Procedure (Example)
Rev.2.00 Mar. 22, 2007 Page 471 of 684 REJ09B0352-0200
15. ROM
15.7
Programming/Erasing Flash Memory
A software method, using the CPU, is employed to program and erase flash memory in the onboard programming modes. There are four flash memory operating modes: program mode, erase mode, program-verify mode, and erase-verify mode. Transitions to these modes are made by setting the PSU, ESU, P, E, PV, and EV bits in FLMCR1. The flash memory cannot be read while it is being written or erased. Install the program to control flash memory programming and erasing (programming control program) in on-chip RAM or external memory, and execute the program from there. See section 15.11, Notes on Flash Memory Programming/Erasing, for points to be noted when programming or erasing the flash memory. In the following operation descriptions, wait times after setting or clearing individual bits in FLMCR1 are given as parameters; for details of the wait times, see section 18.2.5, Flash Memory Characteristics. Notes: 1. Operation is not guaranteed if bits SWE, ESU, PSU, EV, PV, E, and P of FLMCR1 are set/reset by a program in flash memory in the corresponding address areas. 2. When programming or erasing, set FWE to 1 (programming/erasing will not be executed if FWE = 0). 3. Programming should be performed in the erased state. Do not perform additional programming on previously programmed addresses.
Rev.2.00 Mar. 22, 2007 Page 472 of 684 REJ09B0352-0200
15. ROM
*3
E=1
Erase setup state
Normal mode FWE = 1
*1
Erase mode E=0
ESU = 1
ESU = 0 Erase-verify mode
FWE = 0
*2
EV = 1 EV = 0 PSU = 1 PSU = 0 PV = 1 PV = 0
On-board SWE = 1 Software programming mode programming Software programming enable disable state SWE = 0 state
**4
P=1 Program mode P=0
Program setup state
Program-verify mode
Notes: In order to perform a normal read of flash memory, SWE must be cleared to 0. Also note that verify-reads can be performed during the programming/erasing process. 1. : Normal mode : On-board programming mode 2. Do not make a state transition by setting/clearing multiple bits simultaneously. 3. After a transition from erase mode to the erase setup state, do not enter erase mode without passing through the software programming enable state. 4. After a transition from program mode to the program setup state, do not enter program mode without passing through the software programming enable state.
Figure 15.10 State Transitions Caused by FLMCR1 Bit Settings 15.7.1 Program Mode
When writing data or programs to flash memory, the program/program-verify flowchart shown in figure 15.11 should be followed. Performing program operations according to this flowchart will enable data or programs to be written to flash memory without subjecting the device to voltage stress or sacrificing program data reliability. Programming should be carried out 128 bytes at a time. Following the elapse of (tsswe) s or more after the SWE bit is set to 1 in flash memory control register 1 (FLMCR1), 128-byte program data is stored in the program data area and reprogram data area, and the 128-byte data in the program data area in RAM is written consecutively to the program address (the lower 8 bits of the first address written to must be H'00 or H'80). 128 consecutive byte data transfers are performed. The program address and program data are latched
Rev.2.00 Mar. 22, 2007 Page 473 of 684 REJ09B0352-0200
15. ROM
in the flash memory. A 128-byte data transfer must be performed even if writing fewer than 128 bytes; in this case, H'FF data must be written to the extra addresses. Next, the watchdog timer is set to prevent overprogramming in the event of program runaway, etc. Set a WDT overflow period greater than (tspsu + tsp + tcp + tcpsu) s. After this, preparation for program mode (program setup) is carried out by setting the PSU bit in FLMCR1, and after the elapse of (tspsu) s or more, the operating mode is switched to program mode by setting the P bit in FLMCR1. The time during which the P bit is set is the flash memory programming time. Make a setting in the program so that the time for one write operation is within the (tsp) s range. The wait time after the P bit is set must be changed according to the degree of progress through the programming operation. For details see section 15.7.3, Notes on Program/Program-Verify Procedure. 15.7.2 Program-Verify Mode
In program-verify mode, the data written in program mode is read to check whether it has been correctly written in the flash memory. After the elapse of a given programming time, the programming mode is exited (the P bit in FLMCR1 is cleared, then the PSU bit is cleared at least (tcp) s later). The watchdog timer is cleared, and the operating mode is switched to program-verify mode by setting the PV bit in FLMCR1. Before reading in program-verify mode, a dummy write of H'FF data should be made to the addresses to be read. The dummy write should be executed after the elapse of (tspv) s or more. When the flash memory is read in this state (verify data is read in 16-bit units), the data at the latched address is read. Wait at least (tspvr) s after the dummy write before performing this read operation. Next, the written data is compared with the verify data, and reprogram data is computed (see figure 15.11) and transferred to the reprogram data area. After 128 bytes of data have been verified, exit program-verify mode, wait for at least (tcpv) s, then clear the SWE bit in FLMCR1. If reprogramming is necessary, set program mode again, and repeat the program/program-verify sequence as before. However, ensure that the program/program-verify sequence is not repeated more than (N) times on the same bits. Leave a wait time of at least (tcswe) s after clearing SWE. 15.7.3 Notes on Program/Program-Verify Procedure
1. The program/program-verify procedure for the H8/3022F is a 128-byte-unit programming algorithm. Note that the algorithm is different from that of the H8/3039F-ZTAT Group (32-byte-unit programming).
Rev.2.00 Mar. 22, 2007 Page 474 of 684 REJ09B0352-0200
15. ROM
In order to perform 128-byte-unit programming, the lower 8 bits of the write start address must be H'00 or H'80. 2. When performing continuous writing of 128-byte data to flash memory, byte-unit transfer should be used. 128-byte data transfer is necessary even when writing fewer than 128 bytes of data. H'FF data must be written to the extra addresses. 3. Verify data is read in word units. 4. The write pulse is applied and a flash memory write executed while the P bit in FLMCR1 is set. In the H8/3022F, write pulses should be applied as follows in the program/program-verify procedure to prevent voltage stress on the device and loss of write data reliability. a. After write pulse application, perform a verify-read in program-verify mode and apply a write pulse again for any bits read as 1 (reprogramming processing). When all the 0-write bits in the 128-byte write data are read as 0 in the verify-read operation, the program/program-verify procedure is completed. In the H8/3022F, the number of loops in reprogramming processing is guaranteed not to exceed the maximum programming count (N). b. After write pulse application, a verify-read is performed in program-verify mode, and programming is judged to have been completed for bits read as 0. The following processing is necessary for programmed bits. When programming is completed at an early stage in the program/program-verify procedure: If programming is completed in the 1st to 6th reprogramming processing loop, additional programming should be performed on the relevant bits. Additional programming should only be performed on bits which first return 0 in a verify-read in certain reprogramming processing. When programming is completed at a late stage in the program/program-verify procedure: If programming is completed in the 7th or later reprogramming processing loop, additional programming is not necessary for the relevant bits. c. If programming of other bits is incomplete in the 128 bytes, reprogramming process should be executed. If a bit for which programming has been judged to be completed is read as 1 in a subsequent verify-read, a write pulse should again be applied to that bit. 5. The period for which the P bit in FLMCR1 is set (the write pulse width) should be changed according to the degree of progress through the program/program-verify procedure. For detailed wait time specifications, see section 18.2.5, Flash Memory Characteristics.
Rev.2.00 Mar. 22, 2007 Page 475 of 684 REJ09B0352-0200
15. ROM
Table 15.8 Wait Time after P Bit Setting
Item Wait time after P bit setting Symbol tSP When reprogramming loop count (n) is 1 to 6 When reprogramming loop count (n) is 7 or more In case of additional programming processing* Note: * Symbol tsp30 tsp200 tsp10
Additional programming processing is necessary only when the reprogramming loop count (n) is 1 to 6.
6. The program/program-verify flowchart for the H8/3022F is shown in figure 15.11. To cover the points noted above, bits on which reprogramming processing is to be executed, and bits on which additional programming is to be executed, must be determined as shown below. Since reprogram data and additional-programming data vary according to the progress of the programming procedure, it is recommended that the following data storage areas (128 bytes each) be provided in RAM. Table 15.9 Reprogram Data Computation Table
Result of Verify-Read after Write Pulse Application (V) 0 1 0 1 (X) Result of Operation 1 0 1 1
(D) 0 0 1 1
Comments Programming completed: reprogramming processing not to be executed Programming incomplete: reprogramming processing to be executed -- Still in erased state: no action
Legend: D: Source data of bits on which programming is executed. X: Source data of bits on which reprogramming is executed.
Rev.2.00 Mar. 22, 2007 Page 476 of 684 REJ09B0352-0200
15. ROM
Table 15.10 Additional-Programming Data Computation Table
Result of Verify-Read after Write Pulse Application (V) 0 (Y) Result of Operation 1
(X') 0
Comments Programming by write pulse application judged to be completed: additional programming processing to be executed Programming by write pulse application incomplete: additional programming processing not to be executed Programming already completed: additional programming processing not to be executed Still in erased state: no action
0
1
0
1 1
0 1
1 1
Legend: X': Data of bits on which reprogramming is executed in a certain reprogramming loop Y: Data of bits on which additional programming is executed
7. It is necessary to execute additional programming processing during the course of the H8/3022F program/program-verify procedure. However, once 128-byte-unit programming is finished, additional programming should not be carried out on the same address area. When executing reprogramming, an erase must be executed first. Note that normal operation of reads, etc., is not guaranteed if additional programming is performed on addresses for which a program/program-verify operation has finished.
Rev.2.00 Mar. 22, 2007 Page 477 of 684 REJ09B0352-0200
15. ROM
Write pulse application subroutine Write Pulse subroutine Enable WDT Set PSU bit in FLMCR1 Wait (tspsu) s Set P bit in FLMCR1 n=1 Wait (tsp30 or tsp200) s Clear P bit in FLMCR1 Wait (tcp) s Clear PSU bit in FLMCR1 Wait (tcpsu) s Disable WDT Wait (tspv) s End of Subroutine Note 6: Write Pulse Width Programming Count (n) Programming Time (z) s 1 tsp30 tsp30 2 tsp30 3 tsp30 4 tsp30 5 tsp30 6 tsp200 7 tsp200 8 tsp200 9 tsp200 10 tsp200 11 tsp200 12 tsp200 13 . . . . . . tsp200 998 tsp200 999 tsp200 1000 Note: Use a 10 s write pulse for additional programming. RAM Program data storage area (128 bytes) Reprogram data storage area (128 bytes) Additional-programming data storage area (128 bytes) No Transfer reprogram data to reprogram data area 128-byte data verification completed? Yes Clear PV bit in FLMCR1 Wait (tcpv) s *7 *4 H'FF dummy write to verify address Increment address Wait (tspvr) s Read verify data No m=1 No *7 *2 nn+1 *7 *7 Set PV bit in FLMCR1 *7 *5, *7 m=0 Successively write 128-byte reprogram data area in RAM to flash memory Sub-routine-call Write Pulse (Write pulse) See Note 6 for pulse width *1 *7 Start of programming Start Set SWE bit in FLMCR1 Wait (tsswe) s Store 128 bytes of program data in program data area and reprogram data area *7 *4
Programming must be executed in the erased state. Do not perform additional programming on addresses that have already been programmed.
Program data = verify data? Yes 6 n? Yes
Additional-programming data computation Transfer additional-programming data to additional-programming data area Reprogram data computation *4
*3
No Notes: 1. Data transfer is performed by byte transfer. The lower 8 bits of 6 n? the first address written to must be H'00 or H'80. A 128-byte data Yes transfer must be performed even if writing fewer than 128 bytes; in this case, H'FF data must be written to the extra addresses. Successively write 128-byte data from 2. Verify data is read in 16-bit (word) units. *1 additional-programming data area 3. Reprogram data is determined by the operation shown in the in RAM to flash memory table below (comparing the data stored in the program data area Sub-routine-call with the verify data). For reprogram data 0 bits, programming is Write Pulse (Additional programming) executed in the next reprogramming loop. Therefore, even bits for which programming has been completed in the 128-byte programming loop will be subject to programming again if they No m = 0? fail the subsequent verify operation. 4. A 128-byte area for storing program data, a 128-byte area for Yes storing reprogram data, and a 128-byte area for storing Clear SWE bit in FLMCR1 additional-programming data must be provided in RAM. The reprogram and additional-programming data contents are Wait (tcswe) s modified as programming proceeds. 5. A write pulse of 30 s or 200 s is applied according to the End of programming progress of the programming operation. See Note 6 for details of the pulse widths. When writing of additional-programming data is executed, a 10 s write pulse should be applied. Reprogram data X' means reprogram data when the write pulse is applied. 7. The wait times and the value of N are shown in table 18.15, Flash Memory Characteristics. Reprogram Data Computation Table Original Data Verify Data Reprogram Data Comments (V) (D) (X) 0 0 1 Programming completed 0 1 0 Programming incomplete: reprogramming to be executed 1 0 1 -- 1 1 1 Still in erased state: no action Additional-Programming Data Computation Table
Reprogram
*7 n (N)? Yes Clear SWE bit in FLMCR1 Wait (tcswe) s Programming failure
No
*7
Reprogram Data Verify Data Additional-Programming Comments (X') (V) Data (Y) Additional programming to be executed 0 0 0 Additional programming not to be executed 0 1 1 Additional programming not to be executed 1 0 1 Additional programming not to be executed 1 1 1
Figure 15.11 H8/3022F Program/Program-Verify Flowchart
Rev.2.00 Mar. 22, 2007 Page 478 of 684 REJ09B0352-0200
15. ROM
15.7.4
Erase Mode
To erase an individual flash memory block, follow the erase/erase-verify flowchart (single-block erase) shown in figure 15.12. To perform data or program erasure, make a 1-bit setting for the flash memory area to be erased in erase block register 1 or 2 (EBR1, EBR2) at least (tsswe) s after setting the SWE bit to 1 in flash memory control register 1 (FLMCR1). Next, set up the watchdog timer to prevent overerasing in the event of program runaway, etc. Set a value greater than (tse) ms + (tsesu + tce + tcesu) s as the WDT overflow period. After this, preparation for erase mode (erase setup) is carried out by setting the ESU bit in FLMCR1, and after the elapse of (tcesu) s or more, the operating mode is switched to erase mode by setting the E bit in FLMCR1. The time during which the E bit is set is the flash memory erase time. Ensure that the erase time does not exceed (tse) ms. Note: With flash memory erasing, preprogramming (setting all memory data in the memory to be erased to all "0") is not necessary before starting the erase procedure. 15.7.5 Erase-Verify Mode
In erase-verify mode, data is read after memory has been erased to check whether it has been correctly erased. After the elapse of a the erase time, erase mode is exited (the E bit in FLMCR1 is cleared, then the ESU bit is cleared at least (tce) s later), the watchdog timer is cleared, and the operating mode is switched to erase-verify mode by setting the EV bit in FLMCR. Before reading in erase-verify mode, a dummy write of H'FF data should be made to the addresses to be read. The dummy write should be executed after the elapse of (tsev) s or more. When the flash memory is read in this state (verify data is read in 16-bit units), the data at the latched address is read. Wait at least (tsevr) s after the dummy write before performing this read operation. If the read data has been erased (all "1"), a dummy write is performed to the next address, and erase-verify is performed. If the read data is unerased, set erase mode again and repeat the erase/erase-verify sequence in the same way. However, ensure that the erase/erase-verify sequence is not repeated more than (N) times. When verification is completed, exit erase-verify mode, and wait for at least (tcev) s. If erasure has been completed on all the erase blocks, clear the SWE bit in FLMCR1. If there are any unerased blocks, make a 1 bit setting for the flash memory area to be erased, and repeat the erase/erase-verify sequence as before. Leave a wait time of at least (tcswe) s after clearing SWE.
Rev.2.00 Mar. 22, 2007 Page 479 of 684 REJ09B0352-0200
15. ROM
Start
*1
Erasing must be performed in block units.
Set SWE bit in FLMCR1 Wait (tsswe) s n=1 Set EBR1 or EBR2 Enable WDT Set ESU bit in FLMCR1 Wait (tsesu) s Set E bit in FLMCR1 Wait (tse) ms Clear E bit in FLMCR1 Wait (tce) s Clear ESU bit in FLMCR1 Wait (tcesu) s Disable WDT Set EV bit in FLMCR1 Wait (tsev) s Set block start address to verify address
*5 *5 *5 *3 *5
Start erase
*5
Halt erase
*5
nn+1
H'FF dummy write to verify address Wait (tsevr) s Increment address Read verify data Verify data = all "1"? Yes No Last address of block? Yes Clear EV bit in FLMCR1 Wait (tcev) s No
*4 *5 *5 *2
No
Clear EV bit in FLMCR1 Wait (tcev) s
*5 *5
Re-erase No
End of erasing of all erase blocks? Yes
n (N)? Yes Clear SWE bit in FLMCR1
*5
Clear SWE bit in FLMCR1 Wait (tcswez) s End of erasing Notes: 1. 2. 3. 4. 5.
Wait (tcswe) s Erase failure
*5
Preprogramming (setting erase block data to all "0") is not necessary. Verify data is read in 16-bit (word) units. Set only one bit in the erase block register (EBR1/EBR2). More than one bit must not be set. Erasing is performed in block units. To erase a number of blocks, each block must be erased in turn. The wait times and the value of N are shown in table 18.15, Flash Memory Characteristics.
Figure 15.12 H8/3022F Erase/Erase-Verify Flowchart
Rev.2.00 Mar. 22, 2007 Page 480 of 684 REJ09B0352-0200
15. ROM
15.8
Protection
There are three kinds of flash memory program/erase protection: hardware protection, software protection, and error protection. 15.8.1 Hardware Protection
Hardware protection refers to a state in which programming/erasing of flash memory is forcibly disabled or aborted. Hardware protection is reset by settings in flash memory control register 1 (FLMCR1), erase block register 1 (EBR1), and erase block register 2 (EBR2). In the errorprotected state, the FLMCR1, FLMCR2, EBR1, and EBR2 settings are retained; the P bit and E bit can be set, but a transition is not made to program mode or erase mode. (See table 15.11.)
Rev.2.00 Mar. 22, 2007 Page 481 of 684 REJ09B0352-0200
15. ROM
Table 15.11 Hardware Protection
Functions Item FWE pin protection Description * When a low level is input to the FWE pin, FLMCR1, EBR1, and EBR2 are initialized, and the program/erase-protected state is 4 entered. * Program Erase No*
2
Verify* No*
2
1
No*
3
Reset/standby protection
*
In a power-on reset (including a WDT power- No on reset) and in standby mode, FLMCR1, FLMCR2, EBR1, and EBR2 are initialized, and the program/erase-protected state is entered. In a reset via the RES pin, the reset state is not entered unless the RES pin is held low until oscillation stabilizes after powering on. In the case of a reset during operation, hold the RES pin low for the RES pulse width 5 specified in the AC Characteristics section. * When a microcomputer operation error (error No generation (FLER=1)) was detected while flash memory was being programmed/erased, error protection is enabled. At this time, the FLMCR and EBR settings are held, but programming/erasing is aborted at the time the error was generated. Error protection is released only by a reset via the RES pin or a WDT reset, or in the hardware standby mode.
No*
3
No*
2
*
Error protection *
No*
3
Yes*
6
Notes: 1. 2. 3. 4. 5.
Two modes: program-verify and erase-verify. Excluding a RAM area overlapping flash memory. All blocks are unerasable and block-by-block specification is not possible. For details see section 15.11, Notes on Flash Memory Programming and Erasing. See section 4.2.2, Reset Sequence, and section 15.11, Notes on Flash Memory Programming and Erasing. The H8/3022F requires a minimum of 20 system clock cycles for a reset during operation. 6. It is possible to perform a program-verify operation on the 128 bytes being programmed, or an erase-verify operation on the block being erased.
Rev.2.00 Mar. 22, 2007 Page 482 of 684 REJ09B0352-0200
15. ROM
15.8.2
Software Protection
Software protection can be implemented by setting the erase block register 1 (EBR1), erase block register 2 (EBR2), and the RAMS bit in the RAM emulation register (RAMER). When software protection is in effect, setting the P or E bit in flash memory control register 1 (FLMCR1), does not cause a transition to program mode or erase mode. (See table 15.12.) Table 15.12 Software Protection
Functions Item Block specification protection Description * Erase protection can be set for individual blocks by settings in erase block register 1 2 (EBR1)* and erase block register 2 2 (EBR2)* . However, programming protection is disabled. Setting EBR1 and EBR2 to H'00 places all blocks in the erase-protected state. Setting the RAMS bit to 1 in the RAM emulation register (RAMER) places all blocks in the program/erase-protected state. No*
3
Program Erase -- No
Verify* Yes
1
* Emulation protection *
No*
4
Yes
Notes: 1. 2. 3. 4.
Two modes: program-verify and erase-verify. When not erasing, clear all EBR1, EBR2 bits to H'00. A RAM area overlapping flash memory can be written to. All blocks are unerasable and block-by-block specification is not possible.
Rev.2.00 Mar. 22, 2007 Page 483 of 684 REJ09B0352-0200
15. ROM
15.8.3
Error Protection
In error protection, an error is detected when H8/3022 Group runaway occurs during flash 1 memory programming/erasing* , or operation is not performed in accordance with the program/erase algorithm, and the program/erase operation is aborted. Aborting the program/erase operation prevents damage to the flash memory due to overprogramming or overerasing. If the H8/3022 Group malfunctions during flash memory programming/erasing, the FLER bit is set to 1 in FLMCR2 and the error protection state is entered. The FLMCR1, FLMCR2, EBR1, and EBR2 settings are retained, but program mode or erase mode is aborted at the point at which the error occurred. Program mode or erase mode cannot be re-entered by re-setting the P or E bit. 2 However, PV and EV bit setting is enabled, and a transition can be made to verify mode.* FLER bit setting conditions are as follows: 1. When the flash memory of the relevant address area is read during programming/erasing (including vector read and instruction fetch) 2. Immediately after exception handling (excluding a reset) during programming/erasing 3. When a SLEEP instruction (including software standby) is executed during programming/erasing Error protection is released only by a power-on reset and in hardware standby mode. Notes: 1. State in which the P bit and E bit in FLMCR1 are set to 1. Note that NMI input is disabled in this state. 2. It is possible to perform a program-verify operation on the 128 bytes being programmed, or an erase-verify on the block being erased.
Rev.2.00 Mar. 22, 2007 Page 484 of 684 REJ09B0352-0200
15. ROM
Figure 15.13 shows the flash memory state transition diagram.
Memory read verify mode RD VF PR ER FLER= 0 P= 1 or E= 1 P= 0 E= 0 Program mode Erase mode RD VF PR ER FLER= 0
Er
set o or r ha sof rdw Re twa a re re st sta set re a sta nd lea nd ndby by by rel se an ea dh sta nd se a ard by n rel d so ware ea se ftware
Re
Reset or hardware standby
(so ror o ftw ccu ar e s rren tan ce db y)
Reset or standby (hardware protection) RD VF PR ER INIT FLER= 0
Error occurrence
ard rh to se y Re ndb sta
w
are
Reset or hardware standby
Error protection mode RD VF PR ER FLER= 1
Software standby mode Software standby mode release
Error protection mode (software standby) RD VF PR ER INIT FLER= 1
Legend RD: Memory read possible VF: Verify-read possible PR: Programming possible ER: Erasing possible
RD: VF: PR: ER: INIT:
Memory read not possible Verify-read not possible Programming not possible Erasing not possible Register (FLMCR, EBR) initialization state
Figure 15.13 Flash Memory State Transitions (Modes 5, 6, and 7 (on-chip ROM enabled), high level applied to FWE pin) The error protection function is invalid for abnormal operations other than the FLER bit setting conditions. Also, if a certain time has elapsed before this protection state is entered, damage may already have been caused to the flash memory. Consequently, this function cannot provide complete protection against damage to flash memory.
Rev.2.00 Mar. 22, 2007 Page 485 of 684 REJ09B0352-0200
15. ROM
To prevent such abnormal operations, therefore, it is necessary to ensure correct operation in accordance with the program/erase algorithm, with the flash write enable (FWE) voltage applied, and to conduct constant monitoring for MCU errors, internally and externally, using the watchdog timer or other means. There may also be cases where the flash memory is in an erroneous programming or erroneous erasing state at the point of transition to this protection mode, or where programming or erasing is not properly carried out because of an abort. In cases such as these, a forced recovery (program rewrite) must be executed using boot mode. However, it may also happen that boot mode cannot be normally initiated because of overprogramming or overerasing. 15.8.4 NMI Input Disable Conditions
While flash memory is being programed/erased and the boot program is executing in the boot 1 mode (however, period up to branching to on-chip RAM area)* , NMI input is disabled because the programming/erasing operations have priority. This is done to avoid the following operation states: 1. Generation of an NMI input during programming/erasing violates the program/erase algorithms and normal operation can not longer be assured. 2. Vector-read cannot be carried out normally* during NMI exception handling during programming/erasing and the microcomputer runs away as a result. 3. If an NMI input is generated during boot program execution, the normal boot mode sequence cannot be executed. Therefore, this LSI has conditions that exceptionally disable NMI inputs only in the on-board programming mode. However, this does not assure normal programming/erasing and microcomputer operation. Thus, when programming or erasing flash memory, all interrupt requests inside and outside the microcomputer, including NMI, must be restricted. NMI inputs are also disabled in the error protection state and the state that holds the P or E bit in FLMCR during flash memory emulation by RAM. Notes: 1. Indicates the period up to branching to the on-chip RAM boot program area. (This branch occurs immediately after user program transfer was completed.) Therefore, after branching to RAM area, NMI input is enabled in states other than the program/erase state. Thus, interrupt requests inside and outside the microcomputer must be disabled until initial writing by user program (writing of vector table and NMI processing program, etc.) is completed.
2
Rev.2.00 Mar. 22, 2007 Page 486 of 684 REJ09B0352-0200
15. ROM
2. In this case, vector read is not performed normally for the following two reasons: a. b. The correct value cannot be read even by reading the flash memory during programming/erasing. (Value is undefined.) If a value has not yet been written to the NMI vector table, NMI exception handling will not be performed correctly.
Rev.2.00 Mar. 22, 2007 Page 487 of 684 REJ09B0352-0200
15. ROM
15.9
Flash Memory Emulation in RAM
Making a setting in the RAM emulation register (RAMER) enables part of RAM to be overlapped onto the flash memory area so that data to be written to flash memory can be emulated in RAM in real time. After the RAMER setting has been made, accesses cannot be made from the flash memory area or the RAM area overlapping flash memory. Emulation can be performed in user mode and user program mode. Figure 15.14 shows an example of emulation of real-time flash memory programming.
Start of emulation program
Set RAMER
Write tuning data to overlap RAM
Execute application program
No
Tuning OK? Yes Clear RAMER
Write to flash memory emulation block
End of emulation program
Figure 15.14 Flowchart for Flash Memory Emulation in RAM
Rev.2.00 Mar. 22, 2007 Page 488 of 684 REJ09B0352-0200
15. ROM
This area can be accessed from both the RAM area and flash memory area H'00000 EB0 H'01000 EB1 H'02000 EB2 H'03000 EB3 H'04000 EB4 H'05000 EB5 H'06000 EB6 H'07000 EB7 H'08000 H'FDF10 H'FE000 H'FEFFF On-chip RAM H'FFF0F H'3FFFF
Flash memory EB8 to EB11
Figure 15.15 Example of RAM Overlap Operation Example in which Flash Memory Block Area EB0 is Overlapped 1. Set bits RAMS, RAM2 to RAM0 in RAMER to 1, 0, 0, 0, to overlap part of RAM onto the area (EB0) for which real-time programming is required. 2. Real-time programming is performed using the overlapping RAM. 3. After the program data has been confirmed, the RAMS bit is cleared, releasing RAM overlap. 4. The data written in the overlapping RAM is written into the flash memory space (EB0). Notes: 1. When the RAMS bit is set to 1, program/erase protection is enabled for all blocks regardless of the value of RAM2 to RAM0 (emulation protection). In this state, setting the P or E bit in flash memory control register 1 (FLMCR1), will not cause a transition to program mode or erase mode. When actually programming or erasing a flash memory area, the RAMS bit should be cleared to 0. 2. A RAM area cannot be erased by execution of software in accordance with the erase algorithm while flash memory emulation in RAM is being used.
Rev.2.00 Mar. 22, 2007 Page 489 of 684 REJ09B0352-0200
15. ROM
3. Block area EB0 includes the vector table. When performing RAM emulation, the vector table is needed by the overlap RAM. 4. As in on-board programming mode, care is required when applying and releasing FWE to prevent erroneous programming or erasing. To prevent erroneous programming and erasing due to program runaway during FWE application, in particular, the watchdog timer should be set when the P or E bit is set to 1 in FLMCR1, even while the emulation function is being used. 5. When the emulation function is used, NMI input is prohibited when the P bit or E bit is set to 1 in FLMCR1, in the same way as with normal programming and erasing. The P and E bits are cleared by a reset (including a watchdog timer reset), in standby mode, when a high level is not being input to the FWE pin, or when the SWE bit in FLMCR1 is 0 while a high level is being input to the FWE pin.
15.10
Flash Memory PROM Mode
The H8/3022F has a PROM mode as well as the on-board programming modes for programming and erasing flash memory. In PROM mode, the on-chip ROM can be freely programmed using a general-purpose PROM programmer that supports the Renesas Technology microcomputer device type with 256-kbyte on-chip flash memory (FZTAT256). 15.10.1 Socket Adapters and Memory Map In PROM mode using a PROM programmer, memory reading (verification) and writing and flash memory initialization (total erasure) can be performed. For these operations, a special socket adapter is mounted in the PROM programmer. The socket adapter product codes are given in table 15.13. In the H8/3022F PROM mode, only the socket adapters shown in this table should be used. Table 15.13 H8/3022F Socket Adapter Product Codes
Part No. HD64F3022F HD64F3022TE HD64F3064F HD64F3064TE Package 80-pin QFP (FP-80A) 80-pin TQFP (TFP-80C) 80-pin QFP (FP-80A) 80-pin TQFP (TFP-80C) Socket Adapter Product Code ME3022ESHF1H ME3022ESNF1H HF3022Q080D4001 DATA I/O CO. HF3022T080D4001 Manufacturer MINATO ELECTRONICS INC.
Rev.2.00 Mar. 22, 2007 Page 490 of 684 REJ09B0352-0200
15. ROM
Figure 15.16 shows the memory map in PROM mode.
MCU mode H'000000 PROM mode H'00000
On-chip ROM
H'03FFFF
H'3FFFF
Figure 15.16 Memory Map in PROM Mode 15.10.2 Notes on Use of PROM Mode 1. A write to a 128-byte programming unit in PROM mode should be performed once only. Erasing must be carried out before reprogramming an address that has already been programmed. 2. When using a PROM programmer to reprogram a device on which on-board programming/erasing has been performed, it is recommended that erasing be carried out before executing programming. 3. The memory is initially in the erased state when the device is shipped by Renesas. For samples for which the erasure history is unknown, it is recommended that erasing be executed to check and correct the initialization (erase) level. 4. The H8/3022F does not support a product identification mode as used with general-purpose EPROMs, and therefore the device name cannot be set automatically in the PROM programmer. 5. Refer to the instruction manual provided with the socket adapter, or other relevant documentation, for information on PROM programmer and associated program versions that are compatible with the PROM mode of the H8/3022F.
Rev.2.00 Mar. 22, 2007 Page 491 of 684 REJ09B0352-0200
15. ROM
15.11
Notes on Flash Memory Programming/Erasing
The following describes notes when using the on-board programming mode, RAM emulation function, and PROM mode. 1. Program/erase with the specified voltage and timing. Applied voltages in excess of the rating can permanently damage the device. Use a PROM programmer that supports Renasas Technology microcomputer device type FZTAT256V3 with 256-kbyte on-chip flash memory. Do not set the PROM programmer at the HN28F101. If the PROM programmer is set to the HN28F101 by mistake, a high level can be input to the FWE pin and the LSI can be destroyed. 2. Notes on powering on/powering off (See figures 15.17 to 15.19.) Input a high level to the FWE pin after verifying Vcc. Before turning off Vcc, set the FWE pin to a low level. When powering on and powering off the Vcc power supply, fix the FWE pin a low level and set the flash memory to the hardware protection mode. Be sure that the powering on and powering off timing is satisfied even when the power is turned off and back on in the event of a power interruption, etc. If this timing is not satisfied, microcomputer runaway, etc., may cause overprogramming or overerasing and the memory cells may not operate normally. 3. Notes on FWE pin High/Low switching (See figures 15.17 to 15.19.) Input FWE in the state microcomputer operation is verified. If the microcomputer does not satisfy the operation confirmation state, fix the FWE pin at a low level to set the protection mode. To prevent erroneous programming/erasing of flash memory, note the following in FWE pin High/Low switching: * Apply an input to the FWE pin after the VCC voltage has stabilized within the rated voltage. If an input is applied to the FWE pin when the microcomputer VCC voltage does not satisfy the rated voltage (VCC = 3.0 V to 3.6 V), flash memory may be erroneously programmed or erased because the microcomputer is in the unconfirmed state. * Apply an input to the FWE pin when the oscillation has stabilized (after the oscillation stabilization time). When turning on the VCC power, apply an input to the FWE pin after holding the RES pin at a low level during the oscillation stabilization time (tosc1=20ms). Do not apply an input to the FWE pin when oscillation is stopped or unstable. * In the boot mode, perform FWE pin High/Low switching during reset.
Rev.2.00 Mar. 22, 2007 Page 492 of 684 REJ09B0352-0200
15. ROM
In transition to the boot mode, input FWE1 and set MD2 to MD0 while the RES input is low. At this time, the FWE and MD2 to MD0 inputs must satisfy the mode programming setup time (tMDS) relative to the reset clear timing. The mode programming setup time is necessary for RES reset timing even in transition from the boot mode to another mode. In reset during operation, the RES pin must be held at a low level for at least 20 system clocks. * In the user program mode, FWE=High/Low switching is possible regardless of the RES input. FWE input switching is also possible during program execution on flash memory. * Apply an input to FWE when the program is not running away. When applying an input to the FWE pin, the program execution state must be supervised using a watchdog timer, etc. * Input low level to the FWE pin when the SWE, ESU, PSU, EV, PV, E, and P bits in FLMCR1 have been cleared. Do not erroneously set the SWE, ESU, PSU, EV, PV, E, or P bit when applying or releasing FWE. 4. Do not input a constant high level to the FWE pin. To prevent erroneous programming/erasing in the event of program runaway, etc., input a high level to the FWE pin only when programming/erasing flash memory (including flash memory emulation by RAM). Avoid system configurations that constantly input a high level to the FWE pin. Handle program runaway, etc. by starting the watchdog timer so that flash memory is not overprogrammed/overerased even while a high level is input to the FWE pin. 5. Program/erase the flash memory in accordance with the recommended algorithms. The recommended algorithms can program/erase the flash memory without applying voltage stress to the device or sacrificing the reliability of the program data. When setting the PSU and ESU bits in FLMCR1, set the watchdog timer for program runaway, etc. Accesses to flash memory by means of an MOV instruction, etc., are prohibited while the P or E bit is set. 6. Do not set/clear the SWE bit while a program is executing on flash memory. Before performing flash memory program execution or data read, clear the SWE bit. If the SWE bit is set, the flash data can be reprogrammed, but flash memory cannot be accessed for purposes other than verify (verify during programming/erase). Similarly perform flash memory program execution and data read after clearing the SWE bit even when using the RAM emulation function with a high level input to the FWE pin. However, RAM area that overlaps flash memory space can be read/programmed whether the SWE bit is set or cleared.
Rev.2.00 Mar. 22, 2007 Page 493 of 684 REJ09B0352-0200
15. ROM
A wait time is necessary after the SWE bit is cleared. For details see table 18-15 in section 18.2.5, Flash Memory Characteristics. 7. Do not use an interrupt during flash memory programming or erasing. Since programming/erase operations (including emulation by RAM) have priority when a high level is input to the FWE pin, disable all interrupt requests, including NMI. 8. Do not perform additional programming. Reprogram flash memory after erasing. With on-board programming, program to 128-byte programming unit blocks one time only. Program to 128-byte programming unit blocks one time only even in the PROM mode. Erase all the programming unit blocks before reprogramming. 9. Before programming, check that the chip is correctly mounted in the PROM programmer. Overcurrent damage to the device can result if the index marks on the PROM programmer socket, socket adapter, and chip are not correctly aligned. 10. Do not touch the socket adapter or chip during programming. Touching either of these can cause contact faults and write errors. 11. A wait time of 100 s or more is necessary when performing a read after a transition to normal mode from program, erase, or verify mode.
Rev.2.00 Mar. 22, 2007 Page 494 of 684 REJ09B0352-0200
15. ROM
Programming and erase Wait time: possible y
Wait time: x
tOSC1 VCC
Min. 0 s
FWE
tMDS
Min. 200 ns
Min. 0 s
MD2 to MD0*1 tMDS RES
SWE set SWE clear
SWE bit
Flash memory access disabled period (x: Wait time after SWE setting, y: Wait time after SWE clearing)*2 Flash memory reprogrammable period (Flash memory program execution and data read, other than verify, are disabled.) Notes: 1. Always fix the level by pulling down or pulling up the mode pins (MD2 to MD0) until powering off, except for mode switching. 2. See section 18.2.5 Flash Memory Characteristics.
Figure 15.17 Powering On/Off Timing (Boot Mode)
Rev.2.00 Mar. 22, 2007 Page 495 of 684 REJ09B0352-0200
15. ROM
Programming and erase possible
Wait time: x
Wait time: y
tOSC1 VCC
Min. 0 s
FWE
MD2 to MD0*1 tMDS RES
SWE set SWE clear
SWE bit
Flash memory access disabled period (x: Wait time after SWE setting, y: Wait time after SWE clearing)*2 Flash memory reprogrammable period (Flash memory program execution and data read, other than verify, are disabled.) Notes: 1. Always fix the level by pulling down or pulling up the mode pins (MD2 to MD0) up to powering off, except for mode switching. 2. See section 18.2.5 Flash Memory Characteristics.
Figure 15.18 Powering On/Off Timing (User Program Mode)
Rev.2.00 Mar. 22, 2007 Page 496 of 684 REJ09B0352-0200
15. ROM
Programming and erase possible Wait time: x Programming and erase possible Wait time: y Wait time: x Programming and erase possible Programming and erase possible
Wait time: x
Wait time: y
Wait time: y
Wait time: x
tOSC1 VCC
Min 0 s
FWE tMDS tMDS
*2
MD2 to MD0 tMDS tRESW RES
SWE set SWE clear
SWE bit
Mode switching*1 Boot mode Mode User switching*1 mode User program mode User mode User program mode
Flash memory access disabled time (x: Wait time after SWE setting, y: Wait time after SWE clearing)*3 Flash memory reprogammable period (Flash memory program execution and data read, other than verify, are disabled.) Notes: 1. In transition to the boot mode and transition from the boot mode to another mode, mode switching via RES input is necessary. During this switching period (period during which a low level is input to the RES pin), the state of the address dual port and bus control output signals (AS, RD, WR) changes. Therefore, do not use these pins as output signals during this switching period. 2. When making a transition from the boot mode to another mode, the mode programming setup time tMDS relative to the RES clear timing is necessary. 3. See section 18.2.5 Flash Memory Characteristics.
Figure 15.19 Mode Transition Timing (Example: Boot mode User mode User program mode)
Rev.2.00 Mar. 22, 2007 Page 497 of 684 REJ09B0352-0200
Wait time: y
15. ROM
15.12
Overview of Mask ROM
15.12.1 Block Diagram Figure 15.20 shows a block diagram of the ROM.
Internal data bus (upper 8 bits)
Internal data bus (lower 8 bits)
H'00000 H'00002 On-chip ROM H'3FFFE Even addresses
H'00001 H'00003
H'3FFFF Odd addresses
Figure 15.20 Block Diagram of ROM (H8/3022)
Rev.2.00 Mar. 22, 2007 Page 498 of 684 REJ09B0352-0200
15. ROM
15.13
Notes on Ordering Mask ROM Version Chips
When ordering chips with mask ROM, note the following. 1. When ordering through an EPROM, use a 512-kbyte one. 2. Fill all unused addresses with H'FF as shown in figure 15.21 to make the ROM data size the same as for the 512-kbyte version. This applies to ordering through an EPROM and through electrical data transfer. 3. The registers that control the flash memory (FLMCR1, FLMCR2, EBR1, EBR2, and RAMER) are for use exclusively by the flash memory version, and are not provided in the mask ROM version. Reads to the corresponding addresses in the mask ROM version will always return 1, and writes to these addresses are invalid. This point must be noted when switching from the flash memory version to a mask ROM version.
HD6433022 (ROM: 256 kbytes) H'00000 -- H'3FFFF H'00000 HD6433021 (ROM: 192 kbytes) H'00000 -- H'2FFFF H'00000 HD6433020 (ROM: 128 kbytes) H'00000 -- H'1FFFF H'00000
H'2FFFF H'30000 H'3FFFF H'40000 Not used* Not used*
H'1FFFF H'20000
Not used*
H'7FFFF Note: * Write H'FF to all addresses in these areas.
H'7FFFF
H'7FFFF
Figure 15.21 Mask ROM Addresses and Data
Rev.2.00 Mar. 22, 2007 Page 499 of 684 REJ09B0352-0200
15. ROM
15.14
Notes when Converting the F-ZTAT Application Software to the Mask-ROM Versions
Please note the following when converting the F-ZTAT application software to the mask-ROM versions. The values read from the internal registers for the flash ROM or the mask-ROM version and F-ZTAT version differ as follows.
Status Register FLMCR1 Bit FWE F-ZTAT Version 0: Application software running 1: Programming Mask-ROM Version 0: Is not read out 1: Application software running
Note: This difference applies to all the F-ZTAT versions and all the mask-ROM versions that have different ROM size.
Rev.2.00 Mar. 22, 2007 Page 500 of 684 REJ09B0352-0200
16. Clock Pulse Generator
Section 16 Clock Pulse Generator
16.1 Overview
This LSI has a built-in clock pulse generator (CPG) that generates the system clock () and other internal clock signals (/2 to /4096). After duty adjustment, a frequency divider divides the clock 1 frequency to generate the system clock (). The system clock is output at the pin* and furnished as a master clock to prescalers that supply clock signals to the on-chip supporting modules. Frequency division ratios of 1/1, 1/2, 1/4, and 1/8 can be selected for the frequency divider by 2 settings in a division control register (DIVCR).* Power consumption in the chip is reduced in almost direct proportion to the frequency division ratio. Notes: 1. Usage of the pin differs depending on the chip operating mode and the PSTOP bit setting in the module standby control register (MSTCR). For details, see section 17.7, System Clock Output Disabling Function. 2. The division ratio of the frequency divider can be changed dynamically during operation. The clock output at the pin also changes when the division ratio is changed. The frequency output at the pin is shown below. = EXTAL x n EXTAL: n: Frequency of crystal resonator or external clock signal Frequency division ratio (n = 1/1, 1/2, 1/4, or 1/8)
Rev.2.00 Mar. 22, 2007 Page 501 of 684 REJ09B0352-0200
16. Clock Pulse Generator
16.1.1
Block Diagram
Figure 16.1 shows a block diagram of the clock pulse generator.
CPG XTAL Oscillator EXTAL
Duty adjustment circuit
Frequency divider
Prescalers
Division control register
Data bus
/2 to /4096
Figure 16.1 Block Diagram of Clock Pulse Generator
Rev.2.00 Mar. 22, 2007 Page 502 of 684 REJ09B0352-0200
16. Clock Pulse Generator
16.2
Oscillator Circuit
Clock pulses can be supplied by connecting a crystal resonator, or by input of an external clock signal. 16.2.1 Connecting a Crystal Resonator
Circuit Configuration: A crystal resonator can be connected as in the example in figure 16.2. The damping resistance Rd should be selected according to table 16.1. An AT-cut parallelresonance crystal should be used.
C L1 EXTAL
XTAL Rd C L2 C L1 = C L2 = 10 pF to 22 pF
Figure 16.2 Connection of Crystal Resonator (Example) Table 16.1 Damping Resistance Value (Example)
Frequency (MHz) Rd () 2 1k 4 500 8 200 10 0 12 0 16 0 18 0
Crystal Resonator: Figure 16.3 shows an equivalent circuit of the crystal resonator. The crystal resonator should have the characteristics listed in table 16.2.
CL L XTAL Rs EXTAL
CO
AT-cut parallel-resonance type
Figure 16.3 Crystal Resonator Equivalent Circuit
Rev.2.00 Mar. 22, 2007 Page 503 of 684 REJ09B0352-0200
16. Clock Pulse Generator
Table 16.2 Crystal Resonator Parameters
Frequency (MHz) Rs max () Co (pF) 2 500 7 pF max 4 120 8 80 10 70 12 60 16 50 18 40
Use a crystal resonator with a frequency equal to the system clock frequency (). Notes on Board Design: When a crystal resonator is connected, the following points should be noted: Other signal lines should be routed away from the oscillator circuit to prevent induction from interfering with correct oscillation. See figure 16.4. When the board is designed, the crystal resonator and its load capacitors should be placed as close as possible to the XTAL and EXTAL pins.
Avoid C L2 XTAL Signal A Signal B LSI
EXTAL C L1
Figure 16.4 Example of Incorrect Board Design
Rev.2.00 Mar. 22, 2007 Page 504 of 684 REJ09B0352-0200
16. Clock Pulse Generator
16.2.2
External Clock Input
Circuit Configuration: An external clock signal can be input as shown in the examples in figure 16.5. In example b, the clock should be held high in standby mode. If the XTAL pin is left open, the stray capacitance should not exceed 10 pF.
EXTAL
External clock input
XTAL
Open
a. XTAL pin left open
EXTAL
External clock input
XTAL
b. Complementary clock input at XTAL pin
Figure 16.5 External Clock Input (Examples)
Rev.2.00 Mar. 22, 2007 Page 505 of 684 REJ09B0352-0200
16. Clock Pulse Generator
External Clock: The external clock frequency should be equal to the system clock frequency (). Table 16.3 and figure 16.6 indicate the clock timing. Table 16.3 Clock Timing
VCC = 3.0 V to 3.6 V Item External clock rise time External clock fall time External clock input duty (a/tcyc) clock width duty (b/tcyc) Symbol tEXr tEXf -- Min -- -- 30 40 -- 40 Max 10 10 70 60 60 Unit ns ns % % % 5 MHz < 5 MHz Figure 16.6 Test Conditions Figure 16.6
tcyc a
EXTAL
VCC x 0.5
tEXr
tEXf
tcyc b
VCC x 0.5
Figure 16.6 External Clock Input Timing
Rev.2.00 Mar. 22, 2007 Page 506 of 684 REJ09B0352-0200
16. Clock Pulse Generator
Table 16.4 and Figure 16.7 show the timing for the external clock output stabilization delay time. The oscillator and duty correction circuit have the function of regulating the waveform of the external clock input to the EXTAL pin. When the specified clock signal is input to the EXTAL pin, internal clock signal output is confirmed after the elapse of the external clock output stabilization delay time (tDEXT). As clock signal output is not confirmed during the tDEXT period, the reset signal should be driven low and the reset state maintained during this time. Table 16.4 External Clock Output Stabilization Delay Time Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.3 V to 5.5 V, VSS = AVSS = 0 V
Item External clock output stabilization delay time Note: * Symbol tDEXT* Min 500 Max -- Unit s Notes Figure 16.7
tDEXT includes a 10 tcyc RES pulse width (tRESW).
VCC
2.7 V
STBY EXTAL
VIH
RES tDEXT* Note: * tDEXT includes a 10 tcyc RES pulse width (tRESW).
Figure 16.7 External Clock Output Stabilization Delay Time
Rev.2.00 Mar. 22, 2007 Page 507 of 684 REJ09B0352-0200
16. Clock Pulse Generator
16.3
Duty Adjustment Circuit
When the oscillator frequency is 5 MHz or higher, the duty adjustment circuit adjusts the duty cycle of the clock signal from the oscillator to generate the system clock ().
16.4
Prescalers
The prescalers divide the system clock () to generate internal clocks (/2 to /4096).
16.5
Frequency Divider
The frequency divider divides the duty-adjusted clock signal to generate the system clock (). The frequency division ratio can be changed dynamically by modifying the value in DIVCR, as described below. Power consumption in the chip is reduced in almost direct proportion to the frequency division ratio. The system clock generated by the frequency divider can be output at the pin. 16.5.1 Register Configuration
Table 16.5 summarizes the frequency division register. Table 16.5 Frequency Division Register
Address* H'FF5D Note: * Name Division control register Abbreviation DIVCR R/W R/W Initial Value H'FC
The lower 16 bits of the address are shown.
16.5.2
Division Control Register (DIVCR)
DIVCR is an 8-bit readable/writable register that selects the division ratio of the frequency divider.
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 -- 1 -- 2 -- 1 -- 1 DIV1 0 R/W 0 DIV0 0 R/W
Reserved bits Divide bits 1 and 0 These bits select the frequency division ratio
Rev.2.00 Mar. 22, 2007 Page 508 of 684 REJ09B0352-0200
16. Clock Pulse Generator
DIVCR is initialized to H'FC by a reset and in hardware standby mode. It is not initialized in software standby mode. Bits 7 to 2--Reserved: These bits cannot be modified and are always read as 1. Bits 1 and 0--Divide (DIV1 and DIV0): These bits select the frequency division ratio, as follows.
Bit 1 DIV1 0 0 1 1 Bit 0 DIV0 0 1 0 1 Frequency Division Ratio 1/1 1/2 1/4 1/8 (Initial value)
16.5.3
Usage Notes
The DIVCR setting changes the frequency, so note the following points. * Select a frequency division ratio that stays within the assured operation range specified for the clock cycle time tcyc in the AC electrical characteristics. Note that MIN = 1 MHz. Avoid settings that give system clock frequencies less than 1 MHz. * All on-chip module operations are based on . Note that the timing of timer operations, serial communication, and other time-dependent processing differs before and after any change in the division ratio. The waiting time for exit from software standby mode also changes when the division ratio is changed. For details, see section 17.4.3, Selection of Oscillator Waiting Time After Exit from Software Standby Mode.
Rev.2.00 Mar. 22, 2007 Page 509 of 684 REJ09B0352-0200
16. Clock Pulse Generator
Rev.2.00 Mar. 22, 2007 Page 510 of 684 REJ09B0352-0200
17. Power-Down State
Section 17 Power-Down State
17.1 Overview
This LSI has a power-down state that greatly reduces power consumption by halting CPU functions, and a module standby function that reduces power consumption by selectively halting on-chip modules. The power-down state includes the following three modes: * Sleep mode * Software standby mode * Hardware standby mode The module standby function can halt on-chip supporting modules independently of the powerdown state. The modules that can be halted are the ITU, SCI0, SCI1, and A/D converter. Table 17.1 indicates the methods of entering and exiting these power-down modes and the status of the CPU and on-chip supporting modules in each mode.
Rev.2.00 Mar. 22, 2007 Page 511 of 684 REJ09B0352-0200
Table 17.1 Power-Down State and Module Standby Function
State CPU Clock Halted Held Active Active Active Active Active Held output Held CPU Registers ITU SCI0 SCI1 A/D RAM clock output I/O Ports Supporting Modules Exiting Methods * Interrupt * RES * STBY
17. Power-Down State
Entering
Mode
Conditions
Sleep
SLEEP instruc- Active
mode
tion*4 executed
while SSBY = 0
in SYSCR Halted and reset reset reset reset reset and and and and Held Halted Halted Halted Halted Halted Held High output Held * NMI * IRQ0 to IRQ1 * RES * STBY Halted mined reset Active and reset reset reset reset and and and Active -- Halted*1 Halted*1 Halted*1 Halted*1 reset reset reset reset Active -- High impedance*1 -- * STBY * RES * Clear MSTCR bit to 0*3 and and and and and Halted Undeter Halted Halted Halted Halted Halted Held*2 High impedance High impedance * STBY * RES
Software
SLEEP instruc- Halted
Rev.2.00 Mar. 22, 2007 Page 512 of 684 REJ09B0352-0200
standby
tion*4 executed
mode
while SSBY = 1
in SYSCR
Hardware Low input at
standby
STBY pin
mode
Module
Corresponding
standby function
bit set to 1 in
MSTCR
Notes: 1. State in which the corresponding MSTCR bit was set to 1. For details see section 17.2.2, Module Standby Control Register (MSTCR).
2. The RAME bit must be cleared to 0 in SYSCR before the transition from the program execution state to hardware standby mode.
3. When a MSTCR bit is set to 1, the registers of the corresponding on-chip supporting module are initialized. To restart the module, first clear the MSTCR bit to 0, then set up the module registers again. 4. Clear the SWE bit before executing the SLEEP instruction.
Legend SYSCR: SSBY: MSTCR:
System control register Software standby bit Module standby control register
17. Power-Down State
17.2
Register Configuration
This LSI has a system control register (SYSCR) that controls the power-down state, and a module standby control register (MSTCR) that controls the module standby function. Table 17.2 summarizes this register. Table 17.2 Register Configuration
Address* H'FFF2 H'FF5E Note: * Name System control register Module standby control register Lower 16 bits of the address. Abbreviation SYSCR MSTCR R/W R/W R/W Initial Value H'0B H'40
17.2.1
Bit
System Control Register (SYSCR)
7 SSBY 0 R/W 6 STS2 0 R/W 5 STS1 0 R/W 4 STS0 0 R/W 3 UE 1 R/W 2 NMIEG 0 R/W 1 -- 1 -- 0 RAME 1 R/W RAM enable
Initial value Read/Write
Reserved bit NMI edge select User bit enable Standby timer select 2 to 0 These bits select the waiting time at exit from software standby mode Software standby Enables transition to software standby mode
SYSCR is an 8-bit readable/writable register. Bit 7 (SSBY) and bits 6 to 4 (STS2 to STS0) control the power-down state. For information on the other SYSCR bits, see section 3.3, System Control Register.
Rev.2.00 Mar. 22, 2007 Page 513 of 684 REJ09B0352-0200
17. Power-Down State
Bit 7--Software Standby (SSBY): Enables transition to software standby mode. When software standby mode is exited by an external interrupt, this bit remains set to 1 after the return to normal operation. To clear this bit, write 0.
Bit 7 SSBY 0 1 Description SLEEP instruction causes transition to sleep mode SLEEP instruction causes transition to software standby mode (Initial value)
Note: Clear the SWE bit before executing the SLEEP instruction.
Bits 6 to 4--Standby Timer Select (STS2 to STS0): These bits select the length of time the CPU and on-chip supporting modules wait for the clock to settle when software standby mode is exited by an external interrupt. If the clock is generated by a crystal resonator, set these bits according to the clock frequency so that the waiting time (for the clock to stabilize) will be at least 7 ms. See table 17.3. If an external clock is used, any setting is permitted.
Bit 6 STS2 0 Bit 5 STS1 0 Bit 4 STS0 0 1 1 0 1 1 0 0 1 0 1 -- Description Waiting time = 8192 states Waiting time = 16384 states Waiting time = 32768 states Waiting time = 65536 states Waiting time = 131072 states Waiting time = 1024 states Illegal setting (Initial value)
Rev.2.00 Mar. 22, 2007 Page 514 of 684 REJ09B0352-0200
17. Power-Down State
17.2.2
Module Standby Control Register (MSTCR)
MSTCR is an 8-bit readable/writable register that controls output of the system clock (). It also controls the module standby function, which places individual on-chip supporting modules in the standby state. Module standby can be designated for the ITU, SCI0, SCI1, and A/D converter modules.
Bit Initial value Read/Write 7 PSTOP 0 R/W 6 -- 1 -- Reserved bit clock stop Enables or disables output of the system clock Module standby 5 to 3, and 0 These bits select modules to be placed in standby 5 0 R/W 4 0 R/W 3 0 R/W 2 -- 0 -- 1 -- 0 -- 0 MSTOP0 0 R/W
MSTOP5 MSTOP4 MSTOP3
Reserved bit
MSTCR is initialized to H'40 by a reset and in hardware standby mode. It is not initialized in software standby mode. Bit 7-- Clock Stop (PSTOP): Enables or disables output of the system clock ().
Bit 7 PSTOP 0 1 Description System clock output is enabled System clock output is disabled (Initial value)
Bit 6--Reserved: This bit cannot be modified and is always read as 1. Bit 5--Module Standby 5 (MSTOP5): Selects whether to place the ITU in standby.
Bit 5 MSTOP5 0 1 Description ITU operates normally ITU is in standby state (Initial value)
Rev.2.00 Mar. 22, 2007 Page 515 of 684 REJ09B0352-0200
17. Power-Down State
Bit 4--Module Standby 4 (MSTOP4): Selects whether to place SCI0 in standby.
Bit 4 MSTOP4 0 1 Description SCI0 operates normally SCI0 is in standby state (Initial value)
Bit 3--Module Standby 3 (MSTOP3): Selects whether to place SCI1 in standby.
Bit 3 MSTOP3 0 1 Description SCI1 operates normally SCI1 is in standby state (Initial value)
Bits 2 to 1--Reserved: Bits 2 to 1 are reserved. Bit 0--Module Standby 0 (MSTOP0): Selects whether to place the A/D converter in standby.
Bit 0 MSTOP0 0 1 Description A/D converter operates normally A/D converter is in standby state (Initial value)
Rev.2.00 Mar. 22, 2007 Page 516 of 684 REJ09B0352-0200
17. Power-Down State
17.3
17.3.1
Sleep Mode
Transition to Sleep Mode
When the SSBY bit is cleared to 0 in the system control register (SYSCR), execution of the SLEEP instruction causes a transition from the program execution state to sleep mode. Immediately after executing the SLEEP instruction the CPU halts, but the contents of its internal registers are retained. The on-chip supporting modules do not halt in sleep mode. On-chip supporting modules which have been placed in standby by the module standby function, however, remain halted. 17.3.2 Exit from Sleep Mode
Sleep mode is exited by an interrupt, or by input at the RES or STBY pin. Exit by Interrupt: An interrupt terminates sleep mode and causes a transition to the interrupt exception handling state. Sleep mode is not exited by an interrupt source in an on-chip supporting module if the interrupt is disabled in the on-chip supporting module. Sleep mode is not exited by an interrupt other then NMI if the interrupt is masked by interrupt priority settings (IPR) and the settings of the I and UI bits in CCR. Exit by RES Input: Low input at the RES pin exits from sleep mode to the reset state. Exit by STBY Input: Low input at the STBY pin exits from sleep mode to hardware standby mode.
Rev.2.00 Mar. 22, 2007 Page 517 of 684 REJ09B0352-0200
17. Power-Down State
17.4
17.4.1
Software Standby Mode
Transition to Software Standby Mode
To enter software standby mode, execute the SLEEP instruction while the SSBY bit is set to 1 in SYSCR. In software standby mode, current dissipation is reduced to an extremely low level because the CPU, clock, and on-chip supporting modules all halt. The on-chip supporting modules are reset and halted. As long as the specified voltage is supplied, however, CPU register contents and onchip RAM data are retained. The settings of the I/O ports are also held. 17.4.2 Exit from Software Standby Mode
Software standby mode can be exited by input of an external interrupt at the NMI, IRQ0, IRQ1, or by input at the RES or STBY pin. Exit by Interrupt: When an NMI, IRQ0, or IRQ1 interrupt request signal is received, the clock oscillator begins operating. After the oscillator settling time selected by bits STS2 to STS0 in SYSCR, stable clock signals are supplied to the entire chip, software standby mode ends, and interrupt exception handling begins. Software standby mode is not exited if the interrupt enable bits of interrupts IRQ0, and IRQ1 are cleared to 0, or if these interrupts are masked in the CPU. Exit by RES Input: When the RES input goes low, the clock oscillator starts and clock pulses are supplied immediately to the entire chip. The RES signal must be held low long enough for the clock oscillator to stabilize. When RES goes high, the CPU starts reset exception handling. Exit by STBY Input: Low input at the STBY pin causes a transition to hardware standby mode.
Rev.2.00 Mar. 22, 2007 Page 518 of 684 REJ09B0352-0200
17. Power-Down State
17.4.3
Selection of Oscillator Waiting Time after Exit from Software Standby Mode
Bits STS2 to STS0 in SYSCR, and its DIV1 and DIV0 in DIVCR should be set as follows. Crystal Resonator: Set STS2 to STS0, and DIV1 and DIV0 so that the waiting time (for the clock to stabilize) is at least 7 ms. Table 17.3 indicates the waiting times that are selected by STS2 to STS0, and DIV1 and DIV0 settings at various system clock frequencies. External Clock: Any value may be set. Table 17.3 Clock Frequency and Waiting Time for Clock to Settle
DIV1 0 DIV0 0 STS2 0 0 0 0 1 1 0 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 1 0 0 0 0 1 1 1 STS1 0 0 1 1 0 0 1 0 0 1 1 0 0 1 0 0 1 1 0 0 1 0 0 1 1 0 0 1 STS0 0 1 0 1 0 1 -- 0 1 0 1 0 1 -- 0 1 0 1 0 1 -- 0 1 0 1 0 1 -- Waiting Time 8,192 states 16,384 32,768 65,536 131,072 1024 states states states states states 18 MHz 0.46 0.91 1.8 3.6 7.3 0.057 0.91 1.8 3.6 7.3 14.6 0.11 1.8 3.6 7.3 14.6 29.1 0.23 3.6 7.3 14.6 29.1 58.3 0.46 16 MHz 0.51 1.0 2.0 4.1 8.2 0.064 1.02 2.0 4.1 8.2 16.4 0.13 2.0 4.1 8.2 16.4 32.8 0.26 4.1 8.2 16.4 32.8 65.5 0.51 12 MHz 0.65 1.3 2.7 5.5 10.9 0.085 1.4 2.7 5.5 10.9 21.8 0.17 2.7 5.5 10.9 21.8 43.7 0.34 5.5 10.9 21.8 43.7 87.4 0.68 10 MHz 0.8 1.6 3.3 6.6 13.1 0.10 1.6 3.3 6.6 13.1 26.2 0.20 3.3 6.6 13.1 26.2 52.4 0.41 6.6 13.1 26.2 52.4 104.9 0.82 8 MHz 1.0 2.0 4.1 8.2 16.4 0.13 2.0 4.1 8.2 16.4 32.8 0.26 4.1 8.2 16.4 32.8 65.5 0.51 8.2 16.4 32.8 65.5 131.1 1.0 6 MHz 1.3 2.7 5.5 10.9 21.8 0.17 2.7 5.5 10.9 21.8 43.7 0.34 5.5 10.9 21.8 43.7 87.4 0.68 10.9 21.8 43.7 87.4 174.8 1.4 4 MHz 2.0 4.1 8.2 16.4 32.8 0.26 4.1 8.2 16.4 32.8 65.5 0.51 8.2 16.4 32.8 65.5 131.1 1.02 16.4 32.8 65.5 131.1 262.1 2.0 2 MHz 4.1 8.2 16.4 32.8 65.5 0.51 8.2 16.4 32.8 65.5 131.1 1.0 16.4 32.8 65.5 131.1 262.1 2.0 32.8 65.5 131.1 262.1 524.3 4.1 1 MHz 8.2 16.4 32.8 65.5 131.1 1.0 16.4 32.8 65.5 131.1 262.1 2.0 32.8 65.5 131.1 262.1 524.3 4.1 65.5 131.1 262.1 524.3 1048.6 8.2 ms ms ms Unit ms
Illegal setting 8192 states 16384 states 32768 states 65536 states 131072 states 1024 states Illegal setting 8192 states 16384 states 32768 states 65536 states 131072 states 1024 states Illegal setting 8192 states 16384 states 32768 states 65536 states 131072 states 1024 states Illegal setting
1
1
: Recommended setting
Rev.2.00 Mar. 22, 2007 Page 519 of 684 REJ09B0352-0200
17. Power-Down State
17.4.4
Sample Application of Software Standby Mode
Figure 17.1 shows an example in which software standby mode is entered at the fall of NMI and exited at the rise of NMI. With the NMI edge select bit (NMIEG) cleared to 0 in SYSCR (selecting the falling edge), an NMI interrupt occurs. Next the NMIEG bit is set to 1 (selecting the rising edge) and the SSBY bit is set to 1; then the SLEEP instruction is executed to enter software standby mode. Software standby mode is exited at the next rising edge of the NMI signal .
Clock oscillator NMI NMIEG SSBY
NMI exception handling NMIEG = 1 SSBY = 1
Software standby mode (powerdown state)
Oscillator settling time (t osc2 )
NMI exception handling
SLEEP instruction
Figure 17.1 NMI Timing for Software Standby Mode (Example) 17.4.5 Usage Note
The I/O ports retain their existing states in software standby mode. If a port is in the high output state, its output current is not reduced.
Rev.2.00 Mar. 22, 2007 Page 520 of 684 REJ09B0352-0200
17. Power-Down State
17.5
17.5.1
Hardware Standby Mode
Transition to Hardware Standby Mode
Regardless of its current state, the chip enters hardware standby mode whenever the STBY pin goes low. Hardware standby mode reduces power consumption drastically by halting all functions of the CPU and on-chip supporting modules. All modules are reset except the on-chip RAM. As long as the specified voltage is supplied, on-chip RAM data is retained. I/O ports are placed in the high-impedance state. Clear the RAME bit to 0 in SYSCR before STBY goes low to retain on-chip RAM data. The inputs at the mode pins (MD2 to MD0) should not be changed during hardware standby mode. 17.5.2 Exit from Hardware Standby Mode
Hardware standby mode is exited by inputs at the STBY and RES pins. While RES is low, when STBY goes high, the clock oscillator starts running. RES should be held low long enough for the clock oscillator to settle. When RES goes high, reset exception handling begins, followed by a transition to the program execution state. 17.5.3 Timing for Hardware Standby Mode
Figure 17.2 shows the timing relationships for hardware standby mode. To enter hardware standby mode, first drive RES low, then drive STBY low. To exit hardware standby mode, first drive STBY high, wait for the clock to settle, then bring RES from low to high.
Rev.2.00 Mar. 22, 2007 Page 521 of 684 REJ09B0352-0200
17. Power-Down State
Clock oscillator RES
STBY
Oscillator settling time Reset exception handling
Figure 17.2 Hardware Standby Mode Timing
Rev.2.00 Mar. 22, 2007 Page 522 of 684 REJ09B0352-0200
17. Power-Down State
17.6
17.6.1
Module Standby Function
Module Standby Timing
The module standby function can halt several of the on-chip supporting modules (the ITU, SCI0, SCI1, and A/D converter) independently of the power-down state. This standby function is controlled by bits MSTOP5 to MSTOP3 and MSTOP0 in MSTCR. When one of these bits is set to 1, the corresponding on-chip supporting module is placed in standby and halts at the beginning of the next bus cycle after the MSTCR write cycle. 17.6.2 Read/Write in Module Standby
When an on-chip supporting module is in module standby, read/write access to its registers is disabled. Read access always results in H'FF data. Write access is ignored. 17.6.3 Usage Notes
When using the module standby function, note the following points. Cancellation of Interrupt Handling: When an on-chip supporting module is placed in standby by the module standby function, its registers are initialized, including registers with interrupt request flags. Consequently, if an interrupt occurs just before the MSTOP bit is set to 1, the interrupt will not be recognized. The interrupt source will not be held pending. Pin States: Pins used by an on-chip supporting module lose their module functions when the module is placed in module standby. What happens after that depends on the particular pin. For details, see section 7, I/O Ports. Pins that change from the input to the output state require special care. For example, if SCI1 is placed in module standby, the receive data pin loses its receive data function and becomes a generic I/O pin. If its data direction bit is set to 1, the pin becomes a data output pin, and its output may collide with external serial data. Data collisions should be prevented by clearing the data direction bit to 0 or taking other appropriate action. Register Resetting: When an on-chip supporting module is halted by the module standby function, all its registers are initialized. To restart the module, after its MSTOP bit is cleared to 0, its registers must be set up again. It is not possible to write to the registers while the MSTOP bit is set to 1.
Rev.2.00 Mar. 22, 2007 Page 523 of 684 REJ09B0352-0200
17. Power-Down State
17.7
System Clock Output Disabling Function
Output of the system clock () can be controlled by the PSTOP bit in MSTCR. When the PSTOP bit is set to 1, output of the system clock halts and the pin is placed in the high-impedance state. Figure 17.3 shows the timing of the stopping and starting of system clock output. When the PSTOP bit is cleared to 0, output of the system clock is enabled. Table 17.4 indicates the state of the pin in various operating states.
MSTCR write cycle (PSTOP = 1) T1 pin High impedance T2 T3 MSTCR write cycle (PSTOP = 0) T1 T2 T3
Figure 17.3 Timing of Starting and Stopping of Clock Oscillation Table 17.4 Pin State in Various Operating States
Operating State Hardware standby Software standby Sleep mode Normal operation PSTOP = 0 High impedance Always high System clock output System clock output PSTOP = 1 High impedance High impedance High impedance High impedance
Rev.2.00 Mar. 22, 2007 Page 524 of 684 REJ09B0352-0200
18. Electrical Characteristics
Section 18 Electrical Characteristics
18.1
18.1.1
Electrical characteristics of Mask ROM Version
Absolute Maximum Ratings
Table 18.1 lists the absolute maximum ratings. Table 18.1 Absolute Maximum Ratings
Item Power supply voltage Input voltage (except port 7) Input voltage (port 7) Analog power supply voltage Analog input voltage Operating temperature Storage temperature Symbol VCC Vin Vin AVCC VAN Topr Tstg Value -0.3 to +4.3 -0.3 to VCC +0.3 -0.3 to AVCC +0.3 -0.3 to +7.0 -0.3 to AVCC +0.3 -20 to +75 -55 to +125 Unit V V V V V C C
Caution: Permanent damage to the chip may result if absolute maximum ratings are exceeded.
Rev.2.00 Mar. 22, 2007 Page 525 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.1.2
DC Characteristics
Table 18.2 lists the DC characteristics. Table 18.3 lists the permissible output currents. Table 18.2 DC Characteristics Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V,VSS = AVSS = 0 V* , Ta = -20C to +75C
Symbol Port A, P80 to P81, PB0 to PB3 VT VT
- + + -
1
Item Schmitt trigger input voltages Input high voltage
Min VCC x 0.2 -- VCC x 0.9
Typ -- --
Max -- VCC x 0.7 -- VCC + 0.3
Unit V V V V
Test Conditions
VT - VT
VCC x 0.04 -- --
RES, STBY, VIH NMI, MD2, MD1, MD0 EXTAL Port 7 Ports 1, 2, 3, 5, 6, 9, PB4, PB5, PB7
VCC x 0.7 VCC x 0.7 VCC x 0.7
-- -- --
VCC + 0.3 VCC + 0.3
V
AVCC + 0.3 V V
Input low voltage
RES, STBY, MD2, MD1, MD0 NMI, EXTAL, ports 1, 2, 3, 5, 6, 7, 9, PB4, PB5, PB7
VIL
-0.3 -0.3
-- --
VCC x 0.1 VCC x 0.2
V V
Output high voltage Output low voltage
All output pins (except RESO)
VOH
VCC - 0.5 VCC x 1.0 -- -- --
-- -- -- -- --
-- -- 0.4 1.0 0.4
V V V V V
IOH = -200 A IOH = -1 mA IOL = 1.0 mA IOL = 5 mA IOL = 1.6 mA
All output pins VOL (except RESO) Ports 1, 2, 5 and B RESO
Rev.2.00 Mar. 22, 2007 Page 526 of 684 REJ09B0352-0200
18. Electrical Characteristics Test Conditions Vin = 0.5 to VCC - 0.5 V Vin = 0.5 to AVCC - 0.5 V Vin = 0.5 to VCC - 0.5 V
Item Input leakage current STBY, NMI, RES, MD2, MD1, MD0 Port 7
Symbol |Iin|
Min --
Typ --
Max 1.0
Unit A
-- -- -- -Ip Cin 10 -- --
-- -- -- -- -- --
1.0 1.0 10.0 300 50 20
A A
Ports 1, 2, 3, 5, |ITSI| leakage current 6, 8 to B Three-state (off state) Input pull-up MOS current Input capacitance RESO Ports 2 and 5 NMI, RES All input pins except NMI and RES Normal operation Sleep mode Standby mode* Analog power supply current
3
A pF
Vin = 0 V Vin = 0 V f = 1 MHz Ta = 25C
Current 2 dissipation*
ICC*
4
-- -- -- --
28 21 0.1 -- 1.7 0.2 --
48 35 10 80 2.8 10 --
mA
f = 18 MHz f = 18 MHz
A
Ta 50C 50C < Ta AVCC = 5.0 V
During A/D conversion Idle
AICC
-- --
mA A V
RAM standby voltage
VRAM
2.0
Notes: 1. If the A/D converter is not used, do not leave the AVCC and AVSS pins open. Connect AVCC to VCC, and connect AVSS to VSS. 2. Current dissipation values are for VIH min = VCC - 0.5 V and VIL max = 0.5 V with all output pins unloaded and the on-chip pull-up transistors in the off state. 3. The values are for VRAM VCC < 3.6 V, VIH min = VCC x 0.9, and VIL max = 0.3 V. 4. ICC depends on VCC and f as follows: ICC max = 3.0 (mA) + 0.7 (mA/MHz V) x VCC x f (normal operation) ICC max = 3.0 (mA) + 0.5 (mA/MHz V) x VCC x f (sleep mode)
Rev.2.00 Mar. 22, 2007 Page 527 of 684 REJ09B0352-0200
18. Electrical Characteristics
Table 18.3 Permissible Output Currents Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V, Ta = -20C to +75C
Item Permissible output low current (per pin) Permissible output low current (total) Ports 1, 2, 5 and B Other output pins Total of 27 pins including ports 1, 2, 5 and B Total of 23 pins, including ports 8, 9, A and B Total of all output pins, including the above Permissible output high current (per pin) Permissible output high current (total) All output pins Total of all output pins IOH IOH IOL Symbol IOL Min -- -- -- -- -- -- -- Typ -- -- -- -- -- -- -- Max 10 2.0 80 65 120 2.0 40 Unit mA mA mA mA mA mA mA
Note: To protect chip reliability, do not exceed the output current values in table 18.3. When driving a Darlington pair or LED, always insert a current-limiting resistor in the output line, as shown in figures 18.1 and 18.2.
Rev.2.00 Mar. 22, 2007 Page 528 of 684 REJ09B0352-0200
18. Electrical Characteristics
LSI
2 k Port
Darlington pair
Figure 18.1 Darlington Pair Drive Circuit (Example)
LSI
Ports
600
LED
Figure 18.2 LED Drive Circuit (Example)
Rev.2.00 Mar. 22, 2007 Page 529 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.1.3
AC Characteristics
Bus timing parameters are listed in table 18.4. Control signal timing parameters are listed in table 18.5. Timing parameters of the on-chip supporting modules are listed in table 18.6. Table 18.4 Bus Timing Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V, = 2 MHz to 18 MHz, Ta = -20C to +75C
Item Clock cycle time Clock low pulse width Clock high pulse width Clock rise time Clock fall time Address delay time Address hold time Address strobe delay time Write strobe delay time Strobe delay time Write data strobe pulse width 1 Write data strobe pulse width 2 Address setup time 1 Address setup time 2 Read data setup time Read data hold time Symbol tcyc tCL tCH tCr tCf tAD tAH tASD tWSD tSD tWSW1* tWSW2* tAS1 tAS2 tRDS tRDH Min 55.5 17 17 -- -- -- 10 -- -- -- 32 62 10 38 15 0 Max 500 -- -- 10 10 25 -- 25 25 25 -- -- -- -- -- -- Unit ns Test Conditions Figure 18.7, Figure 18.8
Rev.2.00 Mar. 22, 2007 Page 530 of 684 REJ09B0352-0200
18. Electrical Characteristics Item Write data delay time Write data setup time 1 Write data setup time 2 Write data hold time Read data access time 1 Read data access time 2 Read data access time 3 Read data access time 4 Precharge time Wait setup time Wait hold time Note: * Symbol tWDD tWDS1 tWDS2 tWDH tACC1* tACC2* tACC3* tACC4* tPCH* tWTS tWTH Min -- 10 -10 20 -- -- -- -- 40 25 5 Max 55 -- -- -- 50 105 20 80 -- -- -- Figure 18.9 Unit ns Test Conditions Figure 18.7, Figure 18.8
The following times depend on the clock cycle time as shown below. tACC1 = 1.5 x tcyc - 34 (ns) tWSW1 = 1.0 x tcyc - 24 (ns) tACC2 = 2.5 x tcyc - 34 (ns) tWSW2 = 1.5 x tcyc - 22 (ns) tACC3 = 1.0 x tcyc - 36 (ns) tPCH = 1.0 x tcyc - 21 (ns) tACC4 = 2.0 x tcyc - 31 (ns)
Rev.2.00 Mar. 22, 2007 Page 531 of 684 REJ09B0352-0200
18. Electrical Characteristics
Table 18.5 Control Signal Timing Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V, = 2 MHz to 18 MHz, Ta = -20C to +75C
Item RES setup time RES pulse width Symbol tRESS tRESW Min 200 10* 200 -- 132 150 Max -- -- -- 100 -- -- Unit ns tcyc ns ns tcyc ns Figure 18.12 Figure 18.11 Test Conditions Figure 18.10
Mode programming setup tMDS time (MD0, MD1, MD2) RESO output delay time NMI setup time (NMI, IRQ0, IRQ1, IRQ4, IRQ5) NMI hold time (NMI, IRQ0, IRQ1, IRQ4, IRQ5) Interrupt pulse width (NMI, IRQ1, IRQ0 when exiting software standby mode) Clock oscillator settling time at reset (crystal) Clock oscillator settling time in software standby (crystal) Note: tRESD tNMIS RESO output pulse width tRESOW
tNMIH
10
--
tNMIW
200
--
tOSC1 tOSC2
20 7
-- --
ms ms
Figure 18.13 Figure 17.1
The reset time during operation is a minimum of 10 system clock cycles in the H8/3022, H8/3021, and H8/3020 mask ROM versions, but the H8/3022 flash memory version requires a minimum of 20 system clock cycles.
Rev.2.00 Mar. 22, 2007 Page 532 of 684 REJ09B0352-0200
18. Electrical Characteristics
Table 18.6 Timing of On-Chip Supporting Modules Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V, = 2 MHz to 18 MHz, Ta = -20C to +75C
Module ITU Item Timer output delay time Timer input setup time Timer clock input setup time Timer clock pulse width SCI Input clock cycle Single edge Both edges Asynchronous Synchronous tSCKr tSCKf tSCKW tTXD tRXS tRXH Symbol tTOCD tTICS tTCKS tTCKWH tTCKWL tScyc Min -- 50 50 1.5 2.5 4 6 -- -- 0.4 -- 100 100 0 tPWD tPRS tPRH -- 50 50 Max 100 -- -- -- -- -- -- 1.5 1.5 0.6 100 -- -- -- 100 -- -- ns Figure 18.14 tScyc ns Figure 18.18 Figure 18.17 tcyc Figure 18.16 Unit ns Test Conditions Figure 18.15
Input clock rise time Input clock fall time Input clock pulse width Transmit data delay time Receive data setup time (synchronous) Receive data hold time (synchronous clock input) Receive data hold time (synchronous clock output) Ports and TPC Output data delay time Input data setup time Input data hold time
Rev.2.00 Mar. 22, 2007 Page 533 of 684 REJ09B0352-0200
18. Electrical Characteristics
5V C = 90 pF: ports 1, 2, 3, 5, 6, 8, RL This LSI output pin C = 30 pF: ports 9, A, B R L = 2.4 k R H = 12 k C RH Input/output timing measurement levels * Low: 0.8 V * High: 2.0 V
Figure 18.3 Output Load Circuit
Rev.2.00 Mar. 22, 2007 Page 534 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.1.4
A/D Conversion Characteristics
Table 18.7 lists the A/D conversion characteristics. Table 18.7 A/D Converter Characteristics Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V, = 2 MHz to 18 MHz, Ta = -20C to +75C
Item Resolution Conversion time Analog input capacitance Permissible signal- source impedance Nonlinearity error Offset error Full-scale error Quantization error Absolute accuracy Min 10 -- -- -- -- -- -- -- -- Typ 10 -- -- -- -- -- -- -- -- Max 10 7.5 20 5 7.5 7.5 7.5 0.5 8.0 Unit bits s pF k LSB LSB LSB LSB LSB
Rev.2.00 Mar. 22, 2007 Page 535 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.2
18.2.1
Electrical characteristics of Flash Memory Version
Absolute Maximum Ratings
Table 18.8 lists the absolute maximum ratings. Table 18.8 Absolute Maximum Ratings
Item Power supply voltage Input voltage (except port 7) Input voltage (port 7) Analog power supply voltage Analog input voltage Operating temperature Storage temperature Symbol VCC Vin Vin AVCC VAN Topr Tstg Value -0.3 to + 4.3 -0.3 to VCC +0.3 -0.3 to AVCC +0.3 -0.3 to + 7.0 -0.3 to AVCC +0.3 -20 to +75* -55 to +125 Unit V V V V V C C
Caution: Permanent damage to the chip may result if absolute maximum ratings are exceeded. Note: * The operating temperature range when programming/erasing flash memory is Ta = 0 to +75C.
Rev.2.00 Mar. 22, 2007 Page 536 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.2.2
DC Characteristics
Table 18.9 lists the DC characteristics. Table 18.10 lists the permissible output currents. Table 18.9 DC Characteristics (1) Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V* , Ta = -20C to +75C (Programming/Erasing Conditions: Ta = 0C to +75C)
Item Schmitt trigger input voltages Input high voltage Port A, P80 to P81, PB0 to PB3 RES, STBY, NMI, MD2, MD1, MD0, FWE EXTAL Port 7 Ports 1, 2, 3, 5, 6, 9, PB4, PB5, PB7 Input low voltage RES, STBY, MD2, MD1, MD0, FWE NMI, EXTAL, ports 1, 2, 3, 5, 6, 7, 9, PB4, PB5, PB7 Output high voltage Output low voltage Input leakage current All output pins Ports 1, 2, 5 and B STBY, NMI, RES, MD2, MD1, MD0, FWE Port 7 |Iin| VOL All output pins VOH VIL Symbol VT- VT
+
1
Min VCC x 0.2 --
Typ -- --
Max -- VCC x 0.7 -- VCC + 0.3 VCC + 0.3
Unit V V V V V
Test Conditions
VT - VT VIH
+
-
VCC x 0.04 -- VCC x 0.9 VCC x 0.7 VCC x 0.7 VCC x 0.7 -- -- -- --
AVCC + 0.3 V VCC + 0.3 V
-0.3 -0.3
-- --
VCC x 0.1 VCC x 0.2
V V
VCC - 0.5 VCC x 1.0 -- -- --
-- -- -- -- --
-- -- 0.4 1.0 1.0
V V V V A
IOH = -200 A IOH = -1 mA IOL = 1.6 mA IOL = 10 mA Vin = 0.5 V to VCC - 0.5 V Vin = 0.5 V to AVCC - 0.5 V
--
--
1.0
A
Rev.2.00 Mar. 22, 2007 Page 537 of 684 REJ09B0352-0200
18. Electrical Characteristics
Test Conditions Vin = 0.5 V to VCC - 0.5 V Vin = 0 V Vin = 0 V f = 1 MHz Ta = 25C ICC*4 -- -- -- -- AICC -- -- VRAM 2.0 28 21 0.1 -- 1.7 0.2 -- 48 35 10 80 2.8 10 -- mA A V A mA f = 18 MHz f = 18 MHz Ta 50C 50C < Ta
Item Three-state leakage current (off state) Input pull-up MOS current Input capacitance Ports 1, 2, 3, 5, 6, 8 to B Ports 2 and 5 NMI, RES All input pins except NMI and RES Normal operation Sleep mode Standby mode*3 Analog power supply current During A/D conversion Idle RAM standby voltage
Symbol |ITSI|
Min --
Typ --
Max 1.0
Unit A
-Ip Cin
10 -- --
-- -- --
300 50 20
A pF
Current dissipation*2 *4
Notes: 1. If the A/D converter is not used, do not leave the AVCC and AVSS pins open. Connect AVCC to VCC, and connect AVSS to VSS. 2. Current dissipation values are for VIH min = VCC - 0.5 V and VIL max = 0.5 V with all output pins unloaded and the on-chip pull-up transistors in the off state. 3. The values are for VRAM VCC < 3.6 V, VIH min = VCC x 0.9, and VIL max = 0.3 V. 4. ICC depends on VCC and f as follows: ICC max = 3.0 (mA) + 0.7 (mA/MHz V) x VCC x f (normal operation) ICC max = 3.0 (mA) + 0.5 (mA/MHz V) x VCC x f (sleep mode) Power supply current value when programming/erasing in flash memory (Ta = 0C to +75C) is 20 mA (max) higher than the power supply current value in normal operation.
Rev.2.00 Mar. 22, 2007 Page 538 of 684 REJ09B0352-0200
18. Electrical Characteristics
Table 18.10 Permissible Output Currents Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V, Ta = -20C to +75C
Item Permissible output low current (per pin) Permissible output low current (total) Ports 1, 2, 5 and B Other output pins Total of 27 pins including ports 1, 2, 5 and B Total of 23 pins, including ports 8, 9, A and B Total of all output pins, including the above Permissible output high current (per pin) Permissible output high current (total) All output pins Total of all output pins IOH IOH IOL Symbol IOL Min -- -- -- Typ -- -- -- Max 10 2.0 80 Unit mA mA mA
--
--
65
mA
--
--
120
mA
-- --
-- --
2.0 40
mA mA
Note: To protect chip reliability, do not exceed the output current values in table 18.10. When driving a Darlington pair or LED, always insert a current-limiting resistor in the output line, as shown in figures 18.4 and 18.5.
Rev.2.00 Mar. 22, 2007 Page 539 of 684 REJ09B0352-0200
18. Electrical Characteristics
LSI
2 k Port
Darlington pair
Figure 18.4 Darlington Pair Drive Circuit (Example)
LSI
Ports
600
LED
Figure 18.5 LED Drive Circuit (Example)
Rev.2.00 Mar. 22, 2007 Page 540 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.2.3
AC Characteristics
Bus timing parameters are listed in table 18.11. Control signal timing parameters are listed in table 18.12. Timing parameters of the on-chip supporting modules are listed in table 18.13. Table 18.11 Bus Timing Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V, = 2 MHz to 18 MHz, Ta = -20C to +75C
Item Clock cycle time Clock low pulse width Clock high pulse width Clock rise time Clock fall time Address delay time Address hold time Address strobe delay time Write strobe delay time Strobe delay time Write data strobe pulse width 1 Write data strobe pulse width 2 Address setup time 1 Address setup time 2 Read data setup time Read data hold time Symbol Min tcyc tCL tCH tCr tCf tAD tAH tASD tWSD tSD tWSW1* tWSW2* tAS1 tAS2 tRDS tRDH 55.5 17 17 -- -- -- 10 -- -- -- 32 62 10 38 15 0 Max 500 -- -- 10 10 25 -- 25 25 25 -- -- -- -- -- -- Unit ns Test Conditions Figure 18.7, Figure 18.8
Rev.2.00 Mar. 22, 2007 Page 541 of 684 REJ09B0352-0200
18. Electrical Characteristics Item Write data delay time Write data setup time 1 Write data setup time 2 Write data hold time Read data access time 1 Read data access time 2 Read data access time 3 Read data access time 4 Precharge time Wait setup time Wait hold time Symbol tWDD tWDS1 tWDS2 tWDH tACC1* tACC2* tACC3* tACC4* tPCH* tWTS tWTH Min -- 10 -10 20 -- -- -- -- 40 25 5 Max 55 -- -- -- 50 105 20 80 -- -- -- ns Figure 18.9 Unit ns Test Conditions Figure 18.7, Figure 18.8
Note: * The following times depend on the clock cycle time as shown below. tWSW1 = 1.0 x tcyc - 24 (ns) tACC1 = 1.5 x tcyc - 34 (ns) tACC2 = 2.5 x tcyc - 34 (ns) tWSW2 = 1.5 x tcyc - 22 (ns) tPCH = 1.0 x tcyc - 21 (ns) tACC3 = 1.0 x tcyc - 36 (ns) tACC4 = 2.0 x tcyc - 31 (ns)
Rev.2.00 Mar. 22, 2007 Page 542 of 684 REJ09B0352-0200
18. Electrical Characteristics
Table 18.12 Control Signal Timing Condition A: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V, = 2 to 18 MHz, Ta = -20C to +75C
Item RES setup time RES pulse width NMI setup time (NMI, IRQ0, IRQ1, IRQ4, IRQ5) NMI hold time (NMI, IRQ0, IRQ1, IRQ4, IRQ5) Interrupt pulse width (NMI, IRQ1, IRQ0 when exiting software standby mode) Clock oscillator settling time at reset (crystal) Clock oscillator settling time in software standby (crystal) Symbol Min tRESS tRESW tNMIS 200 20 150 Max -- -- -- Unit ns tcyc ns Figure 18.12 Test Conditions Figure 18.10
tNMIH
10
--
tNMIW
200
--
tOSC1 tOSC2
20 7
-- --
ms ms
Figure 18.13 Figure 17.1
Rev.2.00 Mar. 22, 2007 Page 543 of 684 REJ09B0352-0200
18. Electrical Characteristics
Table 18.13 Timing of On-Chip Supporting Modules Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V, = 2 to 18 MHz, Ta = -20C to +75C
Module ITU Item Timer output delay time Timer input setup time Timer clock input setup time Timer clock pulse width SCI Input clock cycle Single edge Both edges Asynchronous Synchronous tSCKr tSCKf tSCKW tTXD tRXS tRXH Symbol tTOCD tTICS tTCKS tTCKWH tTCKWL tScyc Min -- 50 50 1.5 2.5 4 6 -- -- 0.4 -- 100 100 0 tPWD tPRS tPRH -- 50 50 Max 100 -- -- -- -- -- -- 1.5 1.5 0.6 100 -- -- -- 100 -- -- ns Figure 18.14 tScyc ns Figure 18.18 Figure 18.17 tcyc Figure 18.16 Unit ns Test Conditions Figure 18.15
Input clock rise time Input clock fall time Input clock pulse width Transmit data delay time Receive data setup time (synchronous) Receive data hold time (synchronous clock input) Receive data hold time (synchronous clock output) Ports and TPC Output data delay time Input data setup time Input data hold time
Rev.2.00 Mar. 22, 2007 Page 544 of 684 REJ09B0352-0200
18. Electrical Characteristics
5V C = 90 pF: ports 1, 2, 3, 5, 6, 8, RL This LSI output pin C = 30 pF: ports 9, A, B R L = 2.4 k R H = 12 k C RH Input/output timing measurement levels * Low: 0.8 V * High: 2.0 V
Figure 18.6 Output Load Circuit
Rev.2.00 Mar. 22, 2007 Page 545 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.2.4
A/D Conversion Characteristics
Table 18.14 lists the A/D conversion characteristics. Table 18.14 A/D Converter Characteristics Conditions: VCC = 3.0 V to 3.6 V, AVCC = 3.6 V to 5.5 V, VSS = AVSS = 0 V, = 2 to 18 MHz, Ta = -20C to +75C
Item Resolution Conversion time Analog input capacitance Permissible signal- source impedance Nonlinearity error Offset error Full-scale error Quantization error Absolute accuracy Min 10 -- -- -- -- -- -- -- -- Typ 10 -- -- -- -- -- -- -- -- Max 10 7.5 20 5 7.5 7.5 7.5 0.5 8.0 Unit bits s pF k LSB LSB LSB LSB LSB
Rev.2.00 Mar. 22, 2007 Page 546 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.2.5
Flash Memory Characteristics
Table 18.15 shows the flash memory characteristics. Table 18.15 Flash Memory Characteristics Conditions: VCC=3.0 V to 3.6 V, AVCC=3.6 V to 5.5 V, VSS=AVSS=0V Ta = 0C to +75C (program/erase operating temperature range)
Symbol
1, 2, 4
Item Programming time* * *
Min --
Typ 10
Max 200
Unit ms/ 128 bytes ms/ block Times s s s s s s s s s s s Times
Comments
tP
Erase time*1,*3,*5 Reprogramming count Programming Wait time after SWE bit setting* Wait time after PSU bit setting*
1
tE NWEC tsswe tspsu tsp30 tsp200 tsp10 tcp
1
-- -- 1 50 28 198 8 5 5 4 2 2 100 --
100 -- 1 50 30 200 10 5 5 4 2 2 100 --
1200 100 -- -- 32 202 12 -- -- -- -- -- -- 1000
1
Wait time after P bit setting (initial) Wait time after P bit setting (initial) Wait time after P bit setting (additional programming) Wait time after P bit clear*1 Wait time after PSU bit clear*
tcpsu tspv
1
Wait time after PV bit setting*
1
Wait time after H'FF dummy write* Wait time after PV bit clear*1 Wait time after SWE bit clear*
1
tspvr tcpv thvcswe
Maximum programming count* *
1,
4
N
Rev.2.00 Mar. 22, 2007 Page 547 of 684 REJ09B0352-0200
18. Electrical Characteristics
Item Erase Wait time after SWE bit setting* Wait time after ESU bit setting* Wait time after E bit setting* * Wait time after E bit clear*1 Wait time after ESU bit clear*
1 1, 5 1
Symbol tsswe tsesu tse tce tcesu tsev tsevr tcev
1
Min 1 100 10 10 10 20 2 4 100 12
Typ 1 100 10 10 10 20 2 4 100 --
Max -- -- 100 -- -- -- -- -- -- 120
Unit s s ms s s s s s s Times
Comments
1
Erase wait time
Wait time after EV bit setting*
1
Wait time after H'FF dummy write*1 Wait time after EV bit clear*1 Wait time after SWE bit clear* Maximum erase count* *
1, 5
tcswe N
Notes: 1. Set the times according to the program/erase algorithms. 2. Programming time per 128 bytes (Shows the total time the P bit in the flash memory control register (FLMCR) is set. It does not include the programming verification time.) 3. Block erase time (Shows the period the E bit in FLMCR is set. It does not include the erase verification time.) 4. To specify the maximum programming time (tP(max)) in the 128-byte programming flowchart, set the max value (1000) for the maximum programming count (N). The wait time after P bit setting (tsp) should be changed as follows according to the programming counter value. Programming counter value of 1 to 6: tsp30 = 30 s Programming counter value of 7 to 1000: tsp200 = 200 s In case of an additional programming counter value (n) of 1 to 6, tSP10 = 10 s 5. For the maximum erase time (tE(max)), the following relationship applies between the wait time after E bit setting (tse) and the maximum erase count (N): tE(max) = Wait time after E bit setting (tse) x maximum erase count (N) To set the maximum erase time, the values of tSE and N should be set so as to satisfy the above formula. Examples: When tse = 100 [ms], N = 12 When tse = 10 [ms], N = 120
Rev.2.00 Mar. 22, 2007 Page 548 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.3
Operational Timing
This section shows timing diagrams. 18.3.1 Bus Timing
Bus timing is shown as follows: * Basic bus cycle: two-state access Figure 18.7 shows the timing of the external two-state access cycle. * Basic bus cycle: three-state access Figure 18.8 shows the timing of the external three-state access cycle. * Basic bus cycle: three-state access with one wait state Figure 18.9 shows the timing of the external three-state access cycle with one wait state inserted.
Rev.2.00 Mar. 22, 2007 Page 549 of 684 REJ09B0352-0200
18. Electrical Characteristics
T1 tcyc tCH tCf tAD A23 to A 0 tPCH tASD AS tAS1 tPCH tASD RD (read) tAS1 tACC1 D7 to D0 (read) tASD WR (write) tAS1 tWSW1 tWDD D7 to D0 (write) tWDS1 tWDH tSD tAH tRDS tRDH tACC3 tSD tAH tACC3 tSD tAH tCr tCL T2
tPCH
Figure 18.7 Basic Bus Cycle: Two-State Access
Rev.2.00 Mar. 22, 2007 Page 550 of 684 REJ09B0352-0200
18. Electrical Characteristics
T1 A23 to A0 tACC4 AS tACC4 RD (read) tACC2 D7 to D0 (read) tWSD WR (write) tAS2 tWDS2 D7 to D0 (write) tWSW2 tRDS T2 T3
Figure 18.8 Basic Bus Cycle: Three-State Access
Rev.2.00 Mar. 22, 2007 Page 551 of 684 REJ09B0352-0200
18. Electrical Characteristics
T1 A23 to A0 AS RD (read) D7 to D0 (read) T2 TW T3
WR (write)
D7 to D0 (write) tWTS WAIT tWTH tWTS tWTH
Figure 18.9 Basic Bus Cycle: Three-State Access with One Wait State
Rev.2.00 Mar. 22, 2007 Page 552 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.3.2
Control Signal Timing
Control signal timing is shown as follows: * Reset input timing Figure 18.10 shows the reset input timing. * Reset output timing Figure 18.11 shows the reset output timing. * Interrupt input timing Figure 18.12 shows the interrupt input timing for NMI and IRQ5, IRQ4, IRQ1, and IRQ0.
tRESS RES tMDS MD2 to MD0 FWE* Note: * The FWE input timing shown is for entering and exiting boot mode. tRESW tRESS
Figure 18.10 Reset Input Timing
tRESD RESO* tRESOW * Flash version does not have RESO output pin tRESD
Figure 18.11 Reset Output Timing
Rev.2.00 Mar. 22, 2007 Page 553 of 684 REJ09B0352-0200
18. Electrical Characteristics
tNMIS NMI tNMIS IRQ E tNMIS IRQ L IRQ E : Edge-sensitive IRQ i IRQ L : Level-sensitive IRQ i (i = 0, 1, 4, and 5) tNMIW NMI IRQ j (j = 0, 1) tNMIH tNMIH
Figure 18.12 Interrupt Input Timing
Rev.2.00 Mar. 22, 2007 Page 554 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.3.3
Clock Timing
Clock timing is shown below. * Oscillator settling timing Figure 18.13 shows the oscillator settling timing.
VCC
STBY tOSC1 RES tOSC1
Figure 18.13 Oscillator Settling Timing 18.3.4 TPC and I/O Port Timing
TPC and I/O port timing is shown below.
T1 tPRS Ports 1 to 3, 5 to 9, A, and B (read) Ports 1 to 3, 5, 6, 8, 9, A, and B (write) tPRH T2 T3
tPWD
Figure 18.14 TPC and I/O Port Input/Output Timing
Rev.2.00 Mar. 22, 2007 Page 555 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.3.5
ITU Timing
ITU timing is shown as follows: * ITU input/output timing Figure 18.15 shows the ITU input/output timing. * ITU external clock input timing Figure 18.16 shows the ITU external clock input timing.
tTOCD Output compare*1 tTICS Input capture*2 Notes: 1. TIOCA0 to TIOCA4, TIOCB0 to TIOCB4, TOCXA4, TOCXB4 2. TIOCA0 to TIOCA4, TIOCB0 to TIOCB4
Figure 18.15 ITU Input/Output Timing
tTCKS tTCKS TCLKA to TCLKD
tTCKWL
tTCKWH
Figure 18.16 ITU External Clock Input Timing
Rev.2.00 Mar. 22, 2007 Page 556 of 684 REJ09B0352-0200
18. Electrical Characteristics
18.3.6
SCI Input/Output Timing
SCI timing is shown as follows: * SCI input clock timing Figure 18.17 shows the SCI input clock timing. * SCI input/output timing (synchronous mode) Figure 18.18 shows the SCI input/output timing in synchronous mode.
tSCKr tSCKf
tSCKW SCK
tScyc
Figure 18.17 SCK Input Clock Timing
tScyc SCK tTXD TxD (transmit data) RxD (receive data)
tRXS
tRXH
Figure 18.18 SCI Input/Output Timing in Synchronous Mode
Rev.2.00 Mar. 22, 2007 Page 557 of 684 REJ09B0352-0200
18. Electrical Characteristics
Rev.2.00 Mar. 22, 2007 Page 558 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Appendix A Instruction Set
A.1 Instruction List
Operand Notation
Symbol Rd Rs Rn ERd ERs ERn (EAd) (EAs) PC SP CCR N Z V C disp + - x / ( ), < > Note: * Description General destination register* General source register* General register* General destination register (address register or 32-bit register) General source register (address register or 32-bit register) General register (32-bit register) Destination operand Source operand Program counter Stack pointer Condition code register N (negative) flag in CCR Z (zero) flag in CCR V (overflow) flag in CCR C (carry) flag in CCR Displacement Transfer from the operand on the left to the operand on the right, or transition from the state on the left to the state on the right Addition of the operands on both sides Subtraction of the operand on the right from the operand on the left Multiplication of the operands on both sides Division of the operand on the left by the operand on the right Logical AND of the operands on both sides Logical OR of the operands on both sides Exclusive logical OR of the operands on both sides NOT (logical complement) Contents of operand General registers include 8-bit registers (R0H to R7H and R0L to R7L) and 16-bit registers (R0 to R7 and E0 to E7).
Rev.2.00 Mar. 22, 2007 Page 559 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Condition Code Notation
Symbol Description Changed according to execution result Undetermined (no guaranteed value) Cleared to 0 Set to 1 Not affected by execution of the instruction Varies depending on conditions, described in notes
Rev.2.00 Mar. 22, 2007 Page 560 of 684 REJ09B0352-0200
* 0 1 --
Appendix A. Instruction Set
Table A.1
Instruction Set
1. Data transfer instructions
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
Mnemonic MOV.B #xx:8, Rd MOV.B Rs, Rd MOV.B @ERs, Rd MOV.B @(d:16, ERs), Rd MOV.B @(d:24, ERs), Rd MOV.B @ERs+, Rd
Operation #xx:8 Rd8 Rs8 Rd8 @ERs Rd8 @(d:16, ERs) Rd8 @(d:24, ERs) Rd8 @ERs Rd8 ERs32+1 ERs32 @aa:8 Rd8 @aa:16 Rd8 @aa:24 Rd8 Rs8 @ERd Rs8 @(d:16, ERd) Rs8 @(d:24, ERd) ERd32-1 ERd32 Rs8 @ERd Rs8 @aa:8 Rs8 @aa:16 Rs8 @aa:24
@aa
Condition Code I HN
Z
V
C
B B B B
2 2 2 4
---- ---- ---- ----
0-- 0-- 0-- 0--
2 2 4 6
B
8
----
0--
10
B
2
----
0--
6
MOV.B @aa:8, Rd MOV.B @aa:16, Rd MOV.B @aa:24, Rd MOV.B Rs, @ERd MOV.B Rs, @(d:16, ERd) MOV.B Rs, @(d:24, ERd) MOV.B Rs, @-ERd
B B B B B
2 4 6 2 4
---- ---- ---- ---- ----
0-- 0-- 0-- 0-- 0--
4 6 8 4 6
B
8
----
0--
10
B
2
----
0--
6
MOV.B Rs, @aa:8 MOV.B Rs, @aa:16 MOV.B Rs, @aa:24 MOV.W #xx:16, Rd MOV.W Rs, Rd MOV.W @ERs, Rd MOV.W @(d:16, ERs), Rd MOV.W @(d:24, ERs), Rd MOV.W @ERs+, Rd
B B B
2 4 6 4 2 2 4
---- ---- ---- ---- ---- ---- ----
0-- 0-- 0-- 0-- 0-- 0-- 0--
4 6 8 4 2 4 6
W #xx:16 Rd16 W Rs16 Rd16 W @ERs Rd16 W @(d:16, ERs) Rd16 W @(d:24, ERs) Rd16 W @ERs Rd16 ERs32+2 @ERd32 W @aa:16 Rd16
8
----
0--
10
2
----
0--
6
MOV.W @aa:16, Rd
4
----
0--
6
Rev.2.00 Mar. 22, 2007 Page 561 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Appendix A. Instruction Set
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
Mnemonic MOV.W @aa:24, Rd MOV.W Rs, @ERd MOV.W Rs, @(d:16, ERd) MOV.W Rs, @(d:24, ERd) MOV.W Rs, @-ERd
Operation
@aa
Condition Code I HN
Z
V
C
W @aa:24 Rd16 W Rs16 @ERd W Rs16 @(d:16, ERd) W Rs16 @(d:24, ERd) W ERd32-2 ERd32 Rs16 @ERd W Rs16 @aa:16 W Rs16 @aa:24 L L L L #xx:32 Rd32 ERs32 ERd32 @ERs ERd32 @(d:16, ERs) ERd32 @(d:24, ERs) ERd32 @ERs ERd32 ERs32+4 ERs32 @aa:16 ERd32 @aa:24 ERd32 ERs32 @ERd ERs32 @(d:16, ERd) ERs32 @(d:24, ERd) ERd32-4 ERd32 ERs32 @ERd ERs32 @aa:16 ERs32 @aa:24 4 6 6 2 4 6 2 4
6
---- ---- ----
0-- 0-- 0--
8 4 6
8
----
0--
8
2
----
0--
6
MOV.W Rs, @aa:16 MOV.W Rs, @aa:24 MOV.L #xx:32, Rd MOV.L ERs, ERd MOV.L @ERs, ERd MOV.L @(d:16, ERs), ERd MOV.L @(d:24, ERs), ERd MOV.L @ERs+, ERd
4 6
---- ---- ---- ---- ---- ----
0-- 0-- 0-- 0-- 0-- 0--
6 8 6 2 8 10
L
10
----
0--
14
L
4
----
0--
10
MOV.L @aa:16, ERd MOV.L @aa:24, ERd MOV.L ERs, @ERd MOV.L ERs, @(d:16, ERd) MOV.L ERs, @(d:24, ERd) MOV.L ERs, @-ERd
L L L L
6 8
---- ---- ---- ----
0-- 0-- 0-- 0--
10 12 8 10
L
10
----
0--
14
L
4
----
0--
10
MOV.L ERs, @aa:16 MOV.L ERs, @aa:24 POP.W Rn
L L
6 8
---- ---- 2 ----
0-- 0-- 0--
10 12 6
W @SP Rn16 SP+2 SP L @SP ERn32 SP+4 SP
POP.L ERn
4 ----
0--
10
Rev.2.00 Mar. 22, 2007 Page 562 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Appendix A. Instruction Set
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
Mnemonic PUSH.W Rn
Operation
@aa
Condition Code I HN
Z
V
C
W SP-2 SP Rn16 @SP L SP-4 SP ERn32 @SP Cannot be used in the H8/3022 Group Cannot be used in the H8/3022 Group 4
2 ----
0--
6
PUSH.L ERn
4 ----
0--
10
MOVFPE @aa:16, Rd MOVTPE Rs, @aa:16
B
Cannot be used in the H8/3022 Group Cannot be used in the H8/3022 Group
B
4
2. Arithmetic instructions
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
Mnemonic ADD.B #xx:8, Rd ADD.B Rs, Rd ADD.W #xx:16, Rd ADD.W Rs, Rd ADD.L #xx:32, ERd
Operation Rd8+#xx:8 Rd8 Rd8+Rs8 Rd8
@aa
Condition Code I -- HN

Z
V
C
B B
2 2 4 2 6
2 2 4 2 6
--
W Rd16+#xx:16 Rd16 W Rd16+Rs16 Rd16 L ERd32+#xx:32 ERd32 ERd32+ERs32 ERd32 Rd8+#xx:8 +C Rd8 Rd8+Rs8 +C Rd8 ERd32+1 ERd32 ERd32+2 ERd32 ERd32+4 ERd32 Rd8+1 Rd8
-- (1) -- (1) -- (2)
ADD.L ERs, ERd
L
2
-- (2)
2
ADDX.B #xx:8, Rd ADDX.B Rs, Rd ADDS.L #1, ERd ADDS.L #2, ERd ADDS.L #4, ERd INC.B Rd INC.W #1, Rd INC.W #2, Rd
B B L L L B
2 2 2 2 2 2 2 2
-- --
(3) (3)
2 2 2 2 2 2 2 2
------------ ------------ ------------

---- ---- ----
-- -- --
W Rd16+1 Rd16 W Rd16+2 Rd16
Rev.2.00 Mar. 22, 2007 Page 563 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Appendix A. Instruction Set
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
Mnemonic INC.L #1, ERd INC.L #2, ERd DAA Rd
Operation ERd32+1 ERd32 ERd32+2 ERd32 Rd8 decimal adjust Rd8 Rd8-Rs8 Rd8
@aa
Condition Code I HN
Z
V
C -- --
L L B
2 2 2
---- ---- --*
2 2 2
*--

SUB.B Rs, Rd SUB.W #xx:16, Rd SUB.W Rs, Rd SUB.L #xx:32, ERd
B
2 4 2 6
--
2 4 2 6
W Rd16-#xx:16 Rd16 W Rd16-Rs16 Rd16 L ERd32-#xx:32 ERd32 ERd32-ERs32 ERd32 Rd8-#xx:8-C Rd8 Rd8-Rs8-C Rd8 ERd32-1 ERd32 ERd32-2 ERd32 ERd32-4 ERd32 Rd8-1 Rd8
-- (1) -- (1) -- (2)
SUB.L ERs, ERd
L
2
-- (2)
2
SUBX.B #xx:8, Rd SUBX.B Rs, Rd SUBS.L #1, ERd SUBS.L #2, ERd SUBS.L #4, ERd DEC.B Rd DEC.W #1, Rd DEC.W #2, Rd DEC.L #1, ERd DEC.L #2, ERd DAS.Rd
B B L L L B
2 2 2 2 2 2 2 2 2 2 2
-- --
(3) (3)
2 2 2 2 2 2 2 2 2 2 2
------------ ------------ ------------

---- ---- ---- ---- ---- --*
-- -- -- -- --
W Rd16-1 Rd16 W Rd16-2 Rd16 L L B ERd32-1 ERd32 ERd32-2 ERd32 Rd8 decimal adjust Rd8 Rd8 x Rs8 Rd16 (unsigned multiplication)
*--
MULXU. B Rs, Rd
B
2
------------
14
MULXU. W Rs, ERd
W Rd16 x Rs16 ERd32 (unsigned multiplication) B Rd8 x Rs8 Rd16 (signed multiplication)
2
------------

22
MULXS. B Rs, Rd
4
----
----
16
MULXS. W Rs, ERd
W Rd16 x Rs16 ERd32 (signed multiplication) B Rd16 / Rs8 Rd16 (RdH: remainder, RdL: quotient) (unsigned division)
4
----
----
24
DIVXU. B Rs, Rd
2
-- -- (6) (7) -- --
14
Rev.2.00 Mar. 22, 2007 Page 564 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Appendix A. Instruction Set
Addressing Mode and Instruction Length (bytes) No. of States *1
Operand Size
@-ERn/@ERn+
@(d, ERn)
Mnemonic DIVXU. W Rs, ERd
Operation
@aa
Condition Code I HN Z V C
W ERd32 / Rs16 ERd32 (Ed: remainder, Rd: quotient) (unsigned division) B Rd16 / Rs8 Rd16 (RdH: remainder, RdL: quotient) (signed division)
2
-- -- (6) (7) -- --
22
DIVXS. B Rs, Rd
4
-- -- (8) (7) -- --
16
DIVXS. W Rs, ERd
W ERd32 / Rs16 ERd32 (Ed: remainder, Rd: quotient) (signed division) B B Rd8-#xx:8 Rd8-Rs8 4 2
4
-- -- (8) (7) -- --
24

CMP.B #xx:8, Rd CMP.B Rs, Rd CMP.W #xx:16, Rd CMP.W Rs, Rd CMP.L #xx:32, ERd CMP.L ERs, ERd NEG.B Rd NEG.W Rd NEG.L ERd EXTU.W Rd
-- 2 --
2 2 4 2 4 2 2 2 2 2
W Rd16-#xx:16 W Rd16-Rs16 L L B ERd32-#xx:32 ERd32-ERs32 0-Rd8 Rd8
-- (1) 2 -- (1) -- (2) 2 2 2 2 2 -- (2) -- -- --
6
W 0-Rd16 Rd16 L 0-ERd32 ERd32
W 0 ( of Rd16) L 0 ( of Rd32)
---- 0
0--
EXTU.L ERd
2
---- 0
0--
2
EXTS.W Rd
W ( of Rd16) ( of Rd16) L ( of ERd32) ( of ERd32)
2
----
0--
2
EXTS.L ERd
2
----
0--
2
Rev.2.00 Mar. 22, 2007 Page 565 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Appendix A. Instruction Set
3. Logic instructions
Addressing Mode and Instruction Length (bytes) No. of States *1
Operand Size
@-ERn/@ERn+
@(d, ERn)
Mnemonic AND.B #xx:8, Rd AND.B Rs, Rd AND.W #xx:16, Rd AND.W Rs, Rd AND.L #xx:32, ERd AND.L ERs, ERd OR.B #xx:8, Rd OR.B Rs, Rd OR.W #xx:16, Rd OR.W Rs, Rd OR.L #xx:32, ERd OR.L ERs, ERd XOR.B #xx:8, Rd XOR.B Rs, Rd XOR.W #xx:16, Rd XOR.W Rs, Rd XOR.L #xx:32, ERd XOR.L ERs, ERd NOT.B Rd NOT.W Rd NOT.L ERd
Operation Rd8#xx:8 Rd8 Rd8Rs8 Rd8
@aa
Condition Code I HN Z V C
B B
2 2 4 2 6 4 2 2 4 2 6 4 2 2 4 2 6 4 2 2 2
---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0-- 0--
2 2 4 2 6 4 2 2 4 2 6 4 2 2 4 2 6 4 2 2 2
W Rd16#xx:16 Rd16 W Rd16Rs16 Rd16 L L B B ERd32#xx:32 ERd32 ERd32ERs32 ERd32 Rd8#xx:8 Rd8 Rd8Rs8 Rd8
W Rd16#xx:16 Rd16 W Rd16Rs16 Rd16 L L B B ERd32#xx:32 ERd32 ERd32ERs32 ERd32 Rd8#xx:8 Rd8 Rd8Rs8 Rd8
W Rd16#xx:16 Rd16 W Rd16Rs16 Rd16 L L B ERd32#xx:32 ERd32 ERd32ERs32 ERd32 Rd8 Rd8
W Rd16 Rd16 L Rd32 Rd32
Rev.2.00 Mar. 22, 2007 Page 566 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Appendix A. Instruction Set
4. Shift instructions
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
Mnemonic SHAL.B Rd SHAL.W Rd SHAL.L ERd SHAR.B Rd SHAR.W Rd SHAR.L ERd SHLL.B Rd SHLL.W Rd SHLL.L ERd SHLR.B Rd SHLR.W Rd SHLR.L ERd ROTXL.B Rd ROTXL.W Rd ROTXL.L ERd ROTXR.B Rd ROTXR.W Rd ROTXR.L ERd ROTL.B Rd ROTL.W Rd ROTL.L ERd ROTR.B Rd ROTR.W Rd ROTR.L ERd
Operation
@aa
Condition Code I HN
Z
V
C
B W L B W L B W L B W L B W L B W L B W L B W L
2
---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
0 C MSB LSB
2 2 2 2
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
MSB
LSB
C
2 2
0 C MSB LSB
2 2 2
0 MSB LSB C
2 2 2 2
C MSB
LSB
2 2 2
MSB
LSB
C
2 2 2
C MSB
LSB
2 2 2
MSB
LSB
C
2
Rev.2.00 Mar. 22, 2007 Page 567 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Appendix A. Instruction Set
5. Bit manipulation instructions
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
Mnemonic BSET #xx:3, Rd BSET #xx:3, @ERd BSET #xx:3, @aa:8 BSET Rn, Rd BSET Rn, @ERd BSET Rn, @aa:8 BCLR #xx:3, Rd BCLR #xx:3, @ERd BCLR #xx:3, @aa:8 BCLR Rn, Rd BCLR Rn, @ERd BCLR Rn, @aa:8 BNOT #xx:3, Rd
Operation (#xx:3 of Rd8) 1 (#xx:3 of @ERd) 1 (#xx:3 of @aa:8) 1 (Rn8 of Rd8) 1 (Rn8 of @ERd) 1 (Rn8 of @aa:8) 1 (#xx:3 of Rd8) 0 (#xx:3 of @ERd) 0 (#xx:3 of @aa:8) 0 (Rn8 of Rd8) 0 (Rn8 of @ERd) 0 (Rn8 of @aa:8) 0 (#xx:3 of Rd8) (#xx:3 of Rd8) (#xx:3 of @ERd) (#xx:3 of @ERd) (#xx:3 of @aa:8) (#xx:3 of @aa:8) (Rn8 of Rd8) (Rn8 of Rd8) (Rn8 of @ERd) (Rn8 of @ERd) (Rn8 of @aa:8) (Rn8 of @aa:8) (#xx:3 of Rd8) Z (#xx:3 of @ERd) Z (#xx:3 of @aa:8) Z (Rn8 of @Rd8) Z (Rn8 of @ERd) Z (Rn8 of @aa:8) Z (#xx:3 of Rd8) C
@aa
Condition Code I HN Z V C
B B B B B B B B B B B B B
2 4 4 2 4 4 2 4 4 2 4 4 2
------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------
2 8 8 2 8 8 2 8 8 2 8 8 2
BNOT #xx:3, @ERd
B
4
------------
8
BNOT #xx:3, @aa:8
B
4
------------
8
BNOT Rn, Rd
B
2
------------
2
BNOT Rn, @ERd
B
4
------------
8
BNOT Rn, @aa:8
B
4
------------
8
BTST #xx:3, Rd BTST #xx:3, @ERd BTST #xx:3, @aa:8 BTST Rn, Rd BTST Rn, @ERd BTST Rn, @aa:8 BLD #xx:3, Rd
B B B B B B B
2 4 4 2 4 4 2
------ ------ ------ ------ ------ ------
---- ---- ---- ---- ---- ----
2 6 6 2 6 6 2
----------
Rev.2.00 Mar. 22, 2007 Page 568 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Appendix A. Instruction Set
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
@ERn
Condition Code I HN Z V C
Mnemonic BLD #xx:3, @ERd BLD #xx:3, @aa:8 BILD #xx:3, Rd BILD #xx:3, @ERd BILD #xx:3, @aa:8 BST #xx:3, Rd BST #xx:3, @ERd BST #xx:3, @aa:8 BIST #xx:3, Rd BIST #xx:3, @ERd BIST #xx:3, @aa:8 BAND #xx:3, Rd BAND #xx:3, @ERd BAND #xx:3, @aa:8 BIAND #xx:3, Rd BIAND #xx:3, @ERd BIAND #xx:3, @aa:8 BOR #xx:3, Rd BOR #xx:3, @ERd BOR #xx:3, @aa:8 BIOR #xx:3, Rd BIOR #xx:3, @ERd BIOR #xx:3, @aa:8 BXOR #xx:3, Rd BXOR #xx:3, @ERd BXOR #xx:3, @aa:8 BIXOR #xx:3, Rd BIXOR #xx:3, @ERd BIXOR #xx:3, @aa:8
Operation (#xx:3 of @ERd) C (#xx:3 of @aa:8) C (#xx:3 of Rd8) C (#xx:3 of @ERd) C (#xx:3 of @aa:8) C C (#xx:3 of Rd8) C (#xx:3 of @ERd24) C (#xx:3 of @aa:8) C (#xx:3 of Rd8) C (#xx:3 of @ERd24) C (#xx:3 of @aa:8) C(#xx:3 of Rd8) C C(#xx:3 of @ERd24) C C(#xx:3 of @aa:8) C C (#xx:3 of Rd8) C
C (#xx:3 of @ERd24) C C (#xx:3 of @aa:8) C
B B B B B B B B B B B B B B B B B B B B B B B B B B B B B
4 4 2 4 4 2 4 4 2 4 4 2 4 4 2 4 4 2 4 4 2 4 4 2 4 4 2 4 4
---------- ---------- ---------- ---------- ----------
6 6 2 6 6 2 8 8 2 8 8 2 6 6 2 6 6 2 6 6 2 6 6 2 6 6 2 6 6
------------ ------------ ------------ ------------ ------------ ------------ ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ----------
C(#xx:3 of Rd8) C C(#xx:3 of @ERd24) C C(#xx:3 of @aa:8) C C (#xx:3 of Rd8) C
C (#xx:3 of @ERd24) C C (#xx:3 of @aa:8) C
C (#xx:3 of Rd8) C C (#xx:3 of @ERd24) C C (#xx:3 of @aa:8) C C (#xx:3 of Rd8) C
C (#xx:3 of @ERd24) C C (#xx:3 of @aa:8) C
Rev.2.00 Mar. 22, 2007 Page 569 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@aa
#xx
Rn
Appendix A. Instruction Set
6. Branching instructions
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
Mnemonic BRA d:8 (BT d:8) BRA d:16 (BT d:16) BRN d:8 (BF d:8) BRN d:16 (BF d:16) BHI d:8 BHI d:16 BLS d:8 BLS d:16 BCC d:8 (BHS d:8) BCC d:16 (BHS d:16) BCS d:8 (BLO d:8) BCS d:16 (BLO d:16) BNE d:8 BNE d:16 BEQ d:8 BEQ d:16 BVC d:8 BVC d:16 BVS d:8 BVS d:16 BPL d:8 BPL d:16 BMI d:8 BMI d:16 BGE d:8 BGE d:16 BLT d:8 BLT d:16 BGT d:8 BGT d:16
Operation If condition Always is true then PC PC+d else Never next; CZ=0
@aa
Condition Code I HN Z V C
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
2 4 2 4 2 4
------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------ ------------
4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6 4 6
CZ=1
2 4
C=0
2 4
C=1
2 4
Z=0
2 4
Z=1
2 4
V=0
2 4
V=1
2 4
N=0
2 4
N=1
2 4
NV=0
2 4
N V=1 Z (N V) =0
2 4 2 4
Rev.2.00 Mar. 22, 2007 Page 570 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Appendix A. Instruction Set
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
Mnemonic BLE d:8 BLE d:16
Operation If condition is true then PC PC+d else next; Z (N V) =1
@aa
Condition Code I HN Z V C
-- --
2 4
------------ ------------
4 6
JMP @ERn JMP @aa:24 JMP @@aa:8 BSR d:8
-- PC ERn -- PC aa:24 -- PC @aa:8 -- PC @-SP PC PC+d:8 -- PC @-SP PC PC+d:16 -- PC @-SP PC @ERn -- PC @-SP PC @aa:24 -- PC @-SP PC @aa:8 -- PC @SP+
2 4 2 2
------------ ------------ ------------ ------------ 8 6
4 6 10 8
BSR d:16
4
------------
8
10
JSR @ERn
2
------------
6
JSR @aa:24
4
------------
8
10
JSR @@aa:8
2
------------
8
12
RTS
2 ------------
8
10
Rev.2.00 Mar. 22, 2007 Page 571 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
8
Appendix A. Instruction Set
7. System control instructions
Addressing Mode and Instruction Length (bytes)
@-ERn/@ERn+
No. of States *1
Operand Size
@(d, ERn)
Mnemonic TRAPA #x:2
Operation
@aa
Condition Code I HN Z V C
-- PC @-SP CCR @-SP PC -- CCR @SP+ PC @SP+ -- Transition to powerdown state B B #xx:8 CCR Rs8 CCR 2 2 4 6
2
1 ----------
14
16

RTE
10
SLEEP
------------

2
LDC #xx:8, CCR LDC Rs, CCR LDC @ERs, CCR LDC @(d:16, ERs), CCR LDC @(d:24, ERs), CCR LDC @ERs+, CCR
2 2 6 8
W @ERs CCR W @(d:16, ERs) CCR W @(d:24, ERs) CCR W @ERs CCR ERs32+2 ERs32 W @aa:16 CCR W @aa:24 CCR B CCR Rd8 2

10
12

4
8

LDC @aa:16, CCR LDC @aa:24, CCR STC CCR, Rd STC CCR, @ERd STC CCR, @(d:16, ERd) STC CCR, @(d:24, ERd) STC CCR, @-ERd
6 8
8 10 2 6 8
------------ 4 6 ------------ ------------
W CCR @ERd W CCR @(d:16, ERd) W CCR @(d:24, ERd) W ERd32-2 ERd32 CCR @ERd W CCR @aa:16 W CCR @aa:24 B B B CCR#xx:8 CCR CCR#xx:8 CCR CCR#xx:8 CCR 2 2 2
10
------------
12
4
------------
8
STC CCR, @aa:16 STC CCR, @aa:24 ANDC #xx:8, CCR ORC #xx:8, CCR XORC #xx:8, CCR NOP
6 8
------------ ------------

8 10 2 2 2 2
-- PC PC+2
2 ------------
Rev.2.00 Mar. 22, 2007 Page 572 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
Appendix A. Instruction Set
8. Block transfer instructions
Addressing Mode and Instruction Length (bytes) No. of States *1
Operand Size
@-ERn/@ERn+
@(d, ERn)
Mnemonic EEPMOV. B
Operation
@aa
Condition Code I HN Z V C
-- if R4L 0 then repeat @R5 @R6 R5+1 R5 R6+1 R6 R4L-1 R4L until R4L=0 else next; -- if R4 0 then repeat @R5 @R6 R5+1 R5 R6+1 R6 R4-1 R4 until R4=0 else next;
4 ------------
8+4n*2
EEPMOV. W
4 ------------
8+4n*2
Notes: 1. The number of states is the number of states required for execution when the instruction and its operands are located in on-chip memory. For other cases see section A.3, Number of States Required for Execution. 2. n is the value set in register R4L or R4. (1) Set to 1 when a carry or borrow occurs at bit 11; otherwise cleared to 0. (2) Set to 1 when a carry or borrow occurs at bit 27; otherwise cleared to 0. (3) Retains its previous value when the result is zero; otherwise cleared to 0. (4) Set to 1 when the adjustment produces a carry; otherwise retains its previous value. (5) The number of states required for execution of an instruction that transfers data in synchronization with the E clock is variable. (6) Set to 1 when the divisor is negative; otherwise cleared to 0. (7) Set to 1 when the divisor is zero; otherwise cleared to 0. (8) Set to 1 when the quotient is negative; otherwise cleared to 0.
Rev.2.00 Mar. 22, 2007 Page 573 of 684 REJ09B0352-0200
Advanced
@(d, PC)
Implied
Normal
@@aa
@ERn
#xx
Rn
A.2
Table A.2 Operetion Code Map (1) Instruction when most significant bit of BH is 0. Instruction when most significant bit of BH is 1.
4 ORC ADD SUB Table A.2 Table A.2 (2) (2) CMP OR.B XOR.B AND.B Table A.2 (2) XORC ANDC LDC Table A.2 Table A.2 (2) (2) MOV 5 6 7 8 9 A B C D E ADDX SUBX F Table A.2 (2) Table A.2 (2)
Instruction code:
1st byte 2nd byte AH AL BH BL
2 STC LDC 3
AL
AH
0
1
Appendix A. Instruction Set
0
NOP
Table A.2 (2)
1
Table A.2 Table A.2 Table A.2 Table A.2 (2) (2) (2) (2)
2 MOV.B
Operation Code Maps
Rev.2.00 Mar. 22, 2007 Page 574 of 684 REJ09B0352-0200
BHI DIVXU BST OR BCLR BOR MOV BIOR ADD ADDX CMP SUBX OR XOR AND MOV BIXOR BIAND BILD BXOR BAND BTST BIST BLD XOR AND RTS BSR RTE TRAPA Table A.2 (2) JMP MOV Table A.2 Table A.2 EEPMOV (2) (2) Table A.2 (3) BLS BCC BCS BNE BEQ BVC BVS BPL BMI BGE BSR BLT BGT JSR BLE
3
4
BRA
BRN
5
MULXU
DIVXU
MULXU
6
BSET
BNOT
7
8
9
A
B
C
D
E
F
Table A.2 Operation Code Map (2)
Instruction code:
1st byte 2nd byte AH AL BH BL
1 LDC/STC SLEEP ADD INC ADDS MOV SHLL SHAL SHAR ROTL ROTR EXTU EXTU NEG SHLR ROTXL ROTXR NOT SHAL SHAR ROTL ROTR NEG SUB DEC DEC SUBS CMP BRN ADD ADD CMP SUB CMP SUB OR OR BHI BLS BCC BCS XOR XOR BNE AND AND BEQ BVC BVS BPL BMI BGE BLT BGT BLE DEC DEC EXTS EXTS INC INC INC 2 3 4 5 6 7 8 9 A B C D E F Table A.2 (3)
BH AH AL
0
01
MOV
Table A.2 Table A.2 (3) (3)
0A
INC
0B
ADDS
0F
DAA
10
SHLL
11
SHLR
12
ROTXL
13
ROTXR
17
NOT
1A
DEC
1B
SUBS
1F
DAS
58
BRA
79
MOV
Appendix A. Instruction Set
Rev.2.00 Mar. 22, 2007 Page 575 of 684 REJ09B0352-0200
7A
MOV
Table A.2 Operation Code Map (3) Instruction when most significant bit of DH is 0. Instruction when most significant bit of DH is 1.
Instruction code:
1st byte 2nd byte 3rd byte 4th byte AH AL BH BL CH CL DH DL
Appendix A. Instruction Set
CL 2 3 4 5 6 7 8 9 A B C D E F
AH ALBH BLCH LDC STC STC MULXS DIVXS OR AND BTST BOR BTST BIOR BCLR BIST BCLR BTST BOR BTST BIOR BCLR BIST BCLR BIXOR BIAND BILD BST BXOR BAND BLD BIXOR BIAND BILD BST BXOR BAND BLD XOR LDC
0
1
01406
LDC STC
LDC STC
Rev.2.00 Mar. 22, 2007 Page 576 of 684 REJ09B0352-0200
01C05
MULXS
01D05
DIVXS
01F06
7Cr06 * 1
7Cr07 * 1
7Dr06 * 1
BSET
BNOT
7Dr07 * 1
BSET
BNOT
7Eaa6 * 2
7Eaa7 * 2
7Faa6 * 2
BSET
BNOT
7Faa7 * 2
BSET
BNOT
Notes: 1. r is the register designation field. 2. aa is the absolute address field.
Appendix A. Instruction Set
A.3
Number of States Required for Execution
The tables in this section can be used to calculate the number of states required for instruction execution by the H8/300H CPU. Table A.3 indicates the number of states required per cycle according to the bus size. Table A.4 indicates the number of instruction fetch, data read/write, and other cycles occurring in each instruction. The number of states required for execution of an instruction can be calculated from these two tables as follows: Number of states = I x SI + J x SJ + K x SK + L x SL + M x SM + N x SN Examples of Calculation of Number of States Required for Execution Examples: Advanced mode, stack located in external address space, on-chip supporting modules accessed with 8-bit bus width, external devices accessed in three states with one wait state and 16-bit bus width. BSET #0, @FFFFC7:8 From table A.3, SI = 4 and SL = 3 From table A.4, I = L = 2 and J = K = M = N = 0 Number of states = 2 x 4 + 2 x 3 = 14 JSR @@30 From table A.3, SI = SJ = SK = 4 From table A.4, I = J = K = 2 and L = M = N = 0 Number of states = 2 x 4 + 2 x 4 + 2 x 4 = 24
Rev.2.00 Mar. 22, 2007 Page 577 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Table A.3
Number of States per Cycle
Access Conditions On-Chip Supporting Module 8-Bit Bus 2-State 3-State Access Access 4 6 + 2m External Device 16-Bit Bus 2-State 3-State Access Access 2 3+m
Cycle Instruction fetch SI SK SL SM SN
On-Chip 8-Bit Memory Bus 2 6
16-Bit Bus 3
Branch address read SJ Stack operation Byte data access Word data access Internal operation 3 6 1 2 4 3+m 6 + 2m
Legend m: Number of wait states inserted in external device access
Rev.2.00 Mar. 22, 2007 Page 578 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Table A.4
Number of Cycles per Instruction
Instruction Fetch I 1 1 2 1 3 1 1 1 1 1 1 2 1 3 2 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 1 Branch Addr. Read J Stack Operation K Byte Data Access L Word Data Access M Internal Operation N
Instruction ADD
Mnemonic ADD.B #xx:8, Rd ADD.B Rs, Rd ADD.W #xx:16, Rd ADD.W Rs, Rd ADD.L #xx:32, ERd ADD.L ERs, ERd
ADDS ADDX
ADDS #1/2/4, ERd ADDX #xx:8, Rd ADDX Rs, Rd
AND
AND.B #xx:8, Rd AND.B Rs, Rd AND.W #xx:16, Rd AND.W Rs, Rd AND.L #xx:32, ERd AND.L ERs, ERd
ANDC BAND
ANDC #xx:8, CCR BAND #xx:3, Rd BAND #xx:3, @ERd BAND #xx:3, @aa:8
Bcc
BRA d:8 (BT d:8) BRN d:8 (BF d:8) BHI d:8 BLS d:8 BCC d:8 (BHS d:8) BCS d:8 (BLO d:8) BNE d:8 BEQ d:8 BVC d:8 BVS d:8 BPL d:8 BMI d:8
Rev.2.00 Mar. 22, 2007 Page 579 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Branch Addr. Read J Byte Data Access L Word Data Access M
Instruction Bcc
Mnemonic BGE d:8 BLT d:8 BGT d:8 BLE d:8 BRA d:16 (BT d:16) BRN d:16 (BF d:16) BHI d:16 BLS d:16 BCC d:16 (BHS d:16) BCS d:16 (BLO d:16) BNE d:16 BEQ d:16 BVC d:16 BVS d:16 BPL d:16 BMI d:16 BGE d:16 BLT d:16 BGT d:16 BLE d:16
Instruction Fetch I 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 1 2 2 1 2 2 1 2 2 1 2 2
Stack Operation K
Internal Operation N
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
BCLR
BCLR #xx:3, Rd BCLR #xx:3, @ERd BCLR #xx:3, @aa:8 BCLR Rn, Rd BCLR Rn, @ERd BCLR Rn, @aa:8
2 2
2 2
BIAND
BIAND #xx:3, Rd BIAND #xx:3, @ERd BIAND #xx:3, @aa:8
1 1
BILD
BILD #xx:3, Rd BILD #xx:3, @ERd BILD #xx:3, @aa:8
1 1
Rev.2.00 Mar. 22, 2007 Page 580 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Branch Addr. Read J Byte Data Access L Word Data Access M
Instruction BIOR
Mnemonic BIOR #xx:8, Rd BIOR #xx:8, @ERd BIOR #xx:8, @aa:8
Instruction Fetch I 1 2 2 1 2 2 1 2 2 1 2 2 1 2 2 1 2 2 1 2 2 1 2 2 1 2 2 2 2 2 2
Stack Operation K
Internal Operation N
1 1
BIST
BIST #xx:3, Rd BIST #xx:3, @ERd BIST #xx:3, @aa:8
2 2
BIXOR
BIXOR #xx:3, Rd BIXOR #xx:3, @ERd BIXOR #xx:3, @aa:8
1 1
BLD
BLD #xx:3, Rd BLD #xx:3, @ERd BLD #xx:3, @aa:8
1 1
BNOT
BNOT #xx:3, Rd BNOT #xx:3, @ERd BNOT #xx:3, @aa:8 BNOT Rn, Rd BNOT Rn, @ERd BNOT Rn, @aa:8
2 2
2 2
BOR
BOR #xx:3, Rd BOR #xx:3, @ERd BOR #xx:3, @aa:8
1 1
BSET
BSET #xx:3, Rd BSET #xx:3, @ERd BSET #xx:3, @aa:8 BSET Rn, Rd BSET Rn, @ERd BSET Rn, @aa:8
2 2
2 2 1 2 1 2 2 2
BSR
BSR d:8
Normal Advanced
BSR d:16
Normal Advanced
Rev.2.00 Mar. 22, 2007 Page 581 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Branch Addr. Read J Byte Data Access L Word Data Access M
Instruction BST
Mnemonic BST #xx:3, Rd BST #xx:3, @ERd BST #xx:3, @aa:8
Instruction Fetch I 1 2 2 1 2 2 1 2 2 1 2 2 1 1 2 1 3 1 1 1 1 1 1 2 2 1 1 2 2 1 1 1 1
Stack Operation K
Internal Operation N
2 2
BTST
BTST #xx:3, Rd BTST #xx:3, @ERd BTST #xx:3, @aa:8 BTST Rn, Rd BTST Rn, @ERd BTST Rn, @aa:8
1 1
1 1
BXOR
BXOR #xx:3, Rd BXOR #xx:3, @ERd BXOR #xx:3, @aa:8
1 1
CMP
CMP.B #xx:8, Rd CMP.B Rs, Rd CMP.W #xx:16, Rd CMP.W Rs, Rd CMP.L #xx:32, ERd CMP.L ERs, ERd
DAA DAS DEC
DAA Rd DAS Rd DEC.B Rd DEC.W #1/2, Rd DEC.L #1/2, ERd
DIVXS
DIVXS.B Rs, Rd DIVXS.W Rs, ERd
12 20 12 20 2n +2*
1
DIVXU
DIVXU.B Rs, Rd DIVXU.W Rs, ERd
EEPMOV
EEPMOV.B EEPMOV.W
2n +2*1
EXTS
EXTS.W Rd EXTS.L ERd
EXTU
EXTU.W Rd EXTU.L ERd
Rev.2.00 Mar. 22, 2007 Page 582 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Branch Addr. Read J Byte Data Access L Word Data Access M
Instruction INC
Mnemonic INC.B Rd INC.W #1/2, Rd INC.L #1/2, ERd
Instruction Fetch I 1 1 1 2 2 Normal Advanced 2 2 2 2 2 2 2 2 1 1 2 3 5 2 3 4 1 1 1 2 4 1 1 2 3 1 2 4
Stack Operation K
Internal Operation N
JMP
JMP @ERn JMP @aa:24 JMP @@aa:8
2 1 2 1 2 1 2 1 2 1 2 2 2 2 2
JSR
JSR @ERn
Normal Advanced
JSR @aa:24
Normal Advanced
JSR @@aa:8
Normal Advanced
LDC
LDC #xx:8, CCR LDC Rs, CCR LDC @ERs, CCR LDC @(d:16, ERs), CCR LDC @(d:24, ERs), CCR LDC @ERs+, CCR LDC @aa:16, CCR LDC @aa:24, CCR
1 1 1 1 1 1 2
MOV
MOV.B #xx:8, Rd MOV.B Rs, Rd MOV.B @ERs, Rd MOV.B @(d:16, ERs), Rd MOV.B @(d:24, ERs), Rd MOV.B @ERs+, Rd MOV.B @aa:8, Rd MOV.B @aa:16, Rd MOV.B @aa:24, Rd MOV.B Rs, @ERd MOV.B Rs, @(d:16, ERd) MOV.B Rs, @(d:24, ERd)
1 1 1 1 1 1 1 1 1 1 2
Rev.2.00 Mar. 22, 2007 Page 583 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Branch Addr. Read J Byte Data Access L 1 1 1 1 Word Data Access M
Instruction MOV
Mnemonic MOV.B Rs, @-ERd MOV.B Rs, @aa:8 MOV.B Rs, @aa:16 MOV.B Rs, @aa:24 MOV.W #xx:16, Rd MOV.W Rs, Rd MOV.W @ERs, Rd MOV.W @(d:16, ERs), Rd MOV.W @(d:24, ERs), Rd MOV.W @ERs+, Rd MOV.W @aa:16, Rd MOV.W @aa:24, Rd MOV.W Rs, @ERd MOV.W Rs, @(d:16, ERd) MOV.W Rs, @(d:24, ERd) MOV.W Rs, @-ERd MOV.W Rs, @aa:16 MOV.W Rs, @aa:24 MOV.L #xx:32, ERd MOV.L ERs, ERd MOV.L @ERs, ERd MOV.L @(d:16, ERs), ERd MOV.L @(d:24, ERs), ERd MOV.L @ERs+, ERd MOV.L @aa:16, ERd MOV.L @aa:24, ERd MOV.L ERs, @ERd MOV.L ERs, @(d:16, ERd) MOV.L ERs, @(d:24, ERd) MOV.L ERs, @-ERd MOV.L ERs, @aa:16 MOV.L ERs, @aa:24
Instruction Fetch I 1 1 2 3 2 1 1 2 4 1 2 3 1 2 4 1 2 3 3 1 2 3 5 2 3 4 2 3 5 2 3 4
Stack Operation K
Internal Operation N 2
1 1 1 1 1 1 1 1 1 1 1 1 2 2
2 2 2 2 2 2 2 2 2 2 2 2 2 2
Rev.2.00 Mar. 22, 2007 Page 584 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Branch Addr. Read J Byte Data Access L 1 1 12 20 12 20 Word Data Access M
Instruction MOVFPE MOVTPE MULXS
Mnemonic MOVFPE @aa:16, Rd*2 MOVTPE Rs, @aa:16* MULXS.B Rs, Rd MULXS.W Rs, ERd
2
Instruction Fetch I 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 2 1 3 2 1 1 2 1 2 1 1 1 1 1 1 1 1 1
Stack Operation K
Internal Operation N
MULXU
MULXU.B Rs, Rd MULXU.W Rs, ERd
NEG
NEG.B Rd NEG.W Rd NEG.L ERd
NOP NOT
NOP NOT.B Rd NOT.W Rd NOT.L ERd
OR
OR.B #xx:8, Rd OR.B Rs, Rd OR.W #xx:16, Rd OR.W Rs, Rd OR.L #xx:32, ERd OR.L ERs, ERd
ORC POP
ORC #xx:8, CCR POP.W Rn POP.L ERn
1 2 1 2
2 2 2 2
PUSH
PUSH.W Rn PUSH.L ERn
ROTL
ROTL.B Rd ROTL.W Rd ROTL.L ERd
ROTR
ROTR.B Rd ROTR.W Rd ROTR.L ERd
ROTXL
ROTXL.B Rd ROTXL.W Rd ROTXL.L ERd
Rev.2.00 Mar. 22, 2007 Page 585 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Branch Addr. Read J Byte Data Access L Word Data Access M
Instruction ROTXR
Mnemonic ROTXR.B Rd ROTXR.W Rd ROTXR.L ERd
Instruction Fetch I 1 1 1 2 Normal Advanced 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 3 5 2 3 4 1 2 1 3 1 1
Stack Operation K
Internal Operation N
RTE RTS
RTE RTS
2 1 2
2 2 2
SHAL
SHAL.B Rd SHAL.W Rd SHAL.L ERd
SHAR
SHAR.B Rd SHAR.W Rd SHAR.L ERd
SHLL
SHLL.B Rd SHLL.W Rd SHLL.L ERd
SHLR
SHLR.B Rd SHLR.W Rd SHLR.L ERd
SLEEP STC
SLEEP STC CCR, Rd STC CCR, @ERd STC CCR, @(d:16, ERd) STC CCR, @(d:24, ERd) STC CCR, @-ERd STC CCR, @aa:16 STC CCR, @aa:24
1 1 1 1 1 1 2
SUB
SUB.B Rs, Rd SUB.W #xx:16, Rd SUB.W Rs, Rd SUB.L #xx:32, ERd SUB.L ERs, ERd
SUBS
SUBS #1/2/4, ERd
Rev.2.00 Mar. 22, 2007 Page 586 of 684 REJ09B0352-0200
Appendix A. Instruction Set
Branch Addr. Read J Byte Data Access L Word Data Access M
Instruction SUBX
Mnemonic SUBX #xx:8, Rd SUBX Rs, Rd
Instruction Fetch I 1 1 Normal Advanced 2 2 1 1 2 1 3 2 1
Stack Operation K
Internal Operation N
TRAPA
TRAPA #x:2
1 2
2 2
4 4
XOR
XOR.B #xx:8, Rd XOR.B Rs, Rd XOR.W #xx:16, Rd XOR.W Rs, Rd XOR.L #xx:32, ERd XOR.L ERs, ERd
XORC
XORC #xx:8, CCR
Notes: 1. n is the value set in register R4L or R4. The source and destination are accessed n+1 times each. 2. Not used with this LSI.
Rev.2.00 Mar. 22, 2007 Page 587 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
Appendix B Internal I/O Register Field
B.1
Address (low) H'1C H'1D H'1E H'1F H'20 H'21 H'22 H'23 H'24 H'25 H'26 H'27 H'28 H'29 H'2A H'2B H'2C H'2D H'2E H'2F H'30 H'31 H'32 H'33 H'34 H'35 H'36 H'37 H'38 H'39 H'3A -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
Addresses
Register Name Data Bus Width Bit Names Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Module Name
Rev.2.00 Mar. 22, 2007 Page 588 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
Address (low) H'3B H'3C H'3D H'3E H'3F H'40 H'41 H'42 H'43 H'44 H'45 H'46 H'47 H'48 H'49 H'4A H'4B H'4C H'4D H'4E H'4F H'50 H'51 H'52 H'53 H'54 H'55 H'56 H'57 H'58 H'59 H'5A H'5B H'5C H'5D H'5E H'5F Register Name -- -- -- -- -- FLMCR1 FLMCR2 EBR1 EBR2 -- -- -- RAMCR -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- DIVCR MSTCR -- 8 8 -- 8 8 8 8 8 Data Bus Width Bit Names Bit 7 -- -- -- -- -- FWE FLER EB7 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- PSTOP -- Bit 6 -- -- -- -- -- SWE -- EB6 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Bit 5 -- -- -- -- -- ESU -- EB5 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Bit 4 -- -- -- -- -- PSU -- EB4 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Bit 3 -- -- -- -- -- EV -- EB3 EB11 -- -- -- RAMS -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Bit 2 -- -- -- -- -- PV -- EB2 EB10 -- -- -- RAM2 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Bit 1 -- -- -- -- -- E -- EB1 EB9 -- -- -- RAM1 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- DIV1 -- -- Bit 0 -- -- -- -- -- P -- EB0 EB8 -- -- -- RAM0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- DIV0 MSTOP0 -- System control Flash memory Module Name
MSTOP5 MSTOP4 MSTOP3 -- -- -- -- --
Rev.2.00 Mar. 22, 2007 Page 589 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
Address (low) H'60 H'61 H'62 H'63 H'64 H'65 H'66 H'67 H'68 H'69 H'6A H'6B H'6C H'6D H'6E H'6F H'70 H'71 H'72 H'73 H'74 H'75 H'76 H'77 H'78 H'79 H'7A H'7B H'7C H'7D H'7E H'7F H'80 H'81 Register Name TSTR TSNC TMDR TFCR TCR0 TIOR0 TIER0 TSR0 TCNT0H TCNT0L GRA0H GRA0L GRB0H GRB0L TCR1 TIOR1 TIER1 TSR1 TCNT1H TCNT1L GRA1H GRA1L GRB1H GRB1L TCR2 TIOR2 TIER2 TSR2 TCNT2H TCNT2L GRA2H GRA2L GRB2H GRB2L 16 16 8 8 8 8 16 -- -- -- -- CCLR1 IOB2 -- -- CCLR0 IOB1 -- -- CKEG1 IOB0 -- -- CKEG0 -- -- -- TPSC2 IOA2 OVIE OVF TPSC1 IOA1 IMIEB IMFB TPSC0 IOA0 IMIEA IMFA ITU channel 2 16 16 8 8 8 8 16 -- -- -- -- CCLR1 IOB2 -- -- CCLR0 IOB1 -- -- CKEG1 IOB0 -- -- CKEG0 -- -- -- TPSC2 IOA2 OVIE OVF TPSC1 IOA1 IMIEB IMFB TPSC0 IOA0 IMIEA IMFA ITU channel 1 16 16 Data Bus Width 8 8 8 8 8 8 8 8 16 -- -- -- -- -- Bit Names Bit 7 -- -- Bit 6 -- -- MDF -- CCLR1 IOB2 -- -- Bit 5 -- -- FDIR CMD1 CCLR0 IOB1 -- -- Bit 4 STR4 SYNC4 PWM4 CMD0 CKEG1 IOB0 -- -- Bit 3 STR3 SYNC3 PWM3 BFB4 CKEG0 -- -- -- Bit 2 STR2 SYNC2 PWM2 BFA4 TPSC2 IOA2 OVIE OVF Bit 1 STR1 SYNC1 PWM1 BFB3 TPSC1 IOA1 IMIEB IMFB Bit 0 STR0 SYNC0 PWM0 BFA3 TPSC0 IOA0 IMIEA IMFA ITU channel 0 Module Name ITU (all channels)
Legend ITU: 16-bit integrated timer unit
Rev.2.00 Mar. 22, 2007 Page 590 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
Address (low) H'82 H'83 H'84 H'85 H'86 H'87 H'88 H'89 H'8A H'8B H'8C H'8D H'8E H'8F H'90 H'91 H'92 H'93 H'94 H'95 H'96 H'97 H'98 H'99 H'9A H'9B H'9C H'9D H'9E H'9F Register Name TCR3 TIOR3 TIER3 TSR3 TCNT3H TCNT3L GRA3H GRA3L GRB3H GRB3L BRA3H BRA3L BRB3H BRB3L TOER TOCR TCR4 TIOR4 TIER4 TSR4 TCNT4H TCNT4L GRA4H GRA4L GRB4H GRB4L BRA4H BRA4L BRB4H BRB4L 16 16 16 16 8 8 8 8 8 8 16 -- -- -- -- -- -- -- -- CCLR1 IOB2 -- -- EXB4 -- CCLR0 IOB1 -- -- EXA4 XTGD CKEG1 IOB0 -- -- EB3 -- CKEG0 -- -- -- EB4 -- TPSC2 IOA2 OVIE OVF EA4 OLS4 TPSC1 IOA1 IMIEB IMFB EA3 OLS3 TPSC0 IOA0 IMIEA IMFA ITU (all channel) ITU channel 4 16 16 16 16 Data Bus Width 8 8 8 8 16 Bit Names Bit 7 -- -- -- -- Bit 6 CCLR1 IOB2 -- -- Bit 5 CCLR0 IOB1 -- -- Bit 4 CKEG1 IOB0 -- -- Bit 3 CKEG0 -- -- -- Bit 2 TPSC2 IOA2 OVIE OVF Bit 1 TPSC1 IOA1 IMIEB IMFB Bit 0 TPSC0 IOA0 IMIEA IMFA Module Name ITU channel 3
Legend ITU: 16-bit integrated timer unit
Rev.2.00 Mar. 22, 2007 Page 591 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
Address (low) H'A0 H'A1 H'A2 H'A3 H'A4 Register Name TPMR TPCR NDERB NDERA NDRB*
1
Data Bus Width 8 8 8 8 8 8
Bit Names Bit 7 -- Bit 6 -- Bit 5 -- Bit 4 -- Bit 3 G3NOV Bit 2 G2NOV Bit 1 G1NOV Bit 0 G0NOV
Module Name TPC
G3CMS1 G3CMS0 G2CMS1 G2CMS0 G1CMS1 G1CMS0 G0CMS1 G0CMS0 NDER15 NDER7 NDR15 NDR15 NDR7 NDR7 -- -- -- -- OVF NDER14 NDER6 NDR14 NDR14 NDR6 NDR6 -- -- -- -- WT/IT NDER13 NDER5 NDR13 NDR13 NDR5 NDR5 -- -- -- -- TME NDER12 NDER4 NDR12 NDR12 NDR4 NDR4 -- -- -- -- -- NDER11 NDER3 NDR11 -- NDR3 -- -- NDR11 -- NDR3 -- NDER10 NDER2 NDR10 -- NDR2 -- -- NDR10 -- NDR2 CKS2 NDER9 NDER1 NDR9 -- NDR1 -- -- NDR9 -- NDR1 CKS1 NDER8 NDER0 NDR8 -- NDR0 -- -- NDR8 -- NDR0 CKS0 WDT
H'A5
NDRA*
1
8 8
H'A6
NDRB*
1
8 8
H'A7
NDRA*
1
8 8
H'A8 H'A9 H'AA H'AB H'AC H'AD H'AE H'AF H'B0 H'B1 H'B2 H'B3 H'B4 H'B5 H'B6
TCSR* TCNT* --
2
8 8
2
--
2
-- RSTOE -- -- -- -- CHR
-- -- -- -- -- -- PE
-- -- -- -- -- -- O/E
-- -- -- -- -- -- STOP
-- -- -- -- -- -- MP
-- -- -- -- -- -- CKS1
-- -- -- -- -- -- CKS0 SCI0
RSTCSR* -- -- -- -- SMR BRR SCR TDR SSR RDR SCMR
8
WRST -- -- -- --
8 8 8 8 8 8 8
C/A
TIE
RIE
TE
RE
MPIE
TEIE
CKE1
CKE0
TDRE
RDRF
ORER
FER
PER
TEND
MPB
MPBT
--
--
--
--
SDIR
SINV
--
SMIF
Smart card interface
H'B7
Notes: 1. The address depends on the output trigger setting. 2. For write access to TCSR, TCNT, and RSTCSR, see section 10.2.4, Notes on Register Access. Legend TPC: Programmable timing pattern controller WDT: Watchdog timer SCI: Serial communication interface
Rev.2.00 Mar. 22, 2007 Page 592 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
Address (low) H'B8 H'B9 H'BA H'BB H'BC H'BD H'BE H'BF H'C0 H'C1 H'C2 H'C3 H'C4 H'C5 H'C6 H'C7 H'C8 H'C9 H'CA H'CB H'CC H'CD H'CE H'CF H'D0 H'D1 H'D2 H'D3 H'D4 H'D5 H'D6 H'D7 H'D8 H'D9 H'DA Register Name SMR BRR SCR TDR SSR RDR -- -- P1DDR P2DDR P1DR P2DR P3DDR -- P3DR -- P5DDR P6DDR P5DR P6DR -- P8DDR P7DR P8DR P9DDR PADDR P9DR PADR PBDDR -- PBDR -- P2PCR -- -- 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 Data Bus Width 8 8 8 8 8 8 -- -- P17DDR P27DDR P17 P27 P37DDR -- P37 -- -- -- -- -- -- -- P77 -- -- -- -- P16DDR P26DDR P16 P26 P36DDR -- P36 -- -- -- -- -- -- -- P76 -- -- -- -- P15DDR P25DDR P15 P25 P35DDR -- P35 -- -- P65DDR -- P65 -- -- P75 -- P95DDR -- -- P14DDR P24DDR P14 P24 P34DDR -- P34 -- -- P64DDR -- P64 -- -- P74 -- P94DDR -- -- P13DDR P23DDR P13 P23 P33DDR -- P33 -- P53DDR P63DDR P53 P63 -- -- P73 -- P93DDR -- -- P12DDR P22DDR P12 P22 P32DDR -- P32 -- P52DDR -- P52 -- -- -- P72 -- P92DDR -- -- P11DDR P21DDR P11 P21 P31DDR -- P31 -- P51DDR -- P51 -- -- P81DDR P71 P81 P91DDR -- -- P10DDR P20DDR P10 P20 P30DDR -- P30 -- P50DDR P60DDR P50 P60 -- P80DDR P70 P80 P90DDR Port 8 Port 7 Port 8 Port 9 Port 5 Port 6 Port 5 Port 6 Port 3 Port 1 Port 2 Port 1 Port 2 Port 3 TDRE RDRF ORER FER PER TEND MPB MPBT TIE RIE TE RE MPIE TEIE CKE1 CKE0 Bit Names Bit 7 C/A Bit 6 CHR Bit 5 PE Bit 4 O/E Bit 3 STOP Bit 2 MP Bit 1 CKS1 Bit 0 CKS0 Module Name SCI1
PA7DDR PA6DDR PA5DDR PA4DDR PA3DDR PA2DDR PA1DDR PA0DDR Port A -- PA7 -- PA6 P95 PA5 P94 PA4 P93 PA3 P92 PA2 P91 PA1 P90 PA0 Port 9 Port A
PB7DDR -- -- PB7 -- P27PCR -- -- -- -- -- P26PCR -- --
PB5DDR PB4DDR PB3DDR PB2DDR PB1DDR PB0DDR Port B -- PB5 -- P25PCR -- -- -- PB4 -- P24PCR -- -- -- PB3 -- P23PCR -- -- -- PB2 -- P22PCR -- -- -- PB1 -- P21PCR -- -- -- PB0 -- P20PCR -- -- Port 2 Port B
Rev.2.00 Mar. 22, 2007 Page 593 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
Address (low) H'DB H'DC H'DD H'DE H'DF H'E0 H'E1 H'E2 H'E3 H'E4 H'E5 H'E6 H'E7 H'E8 H'E9 H'EA H'EB H'EC H'ED H'EE H'EF H'F0 H'F1 H'F2 H'F3 H'F4 H'F5 H'F6 H'F7 H'F8 H'F9 H'FA H'FB H'FC H'FD H'FE H'FF -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Register Name P5PCR -- -- -- -- ADDRAH ADDRAL ADDRBH ADDRBL ADDRCH ADDRCL ADDRDH ADDRDL ADCSR ADCR -- -- -- ASTCR WCR WCER -- MDCR SYSCR ADRCR ISCR IER ISR -- IPRA IPRB -- -- 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 -- -- AD9 AD1 AD9 AD1 AD9 AD1 AD9 AD1 ADF TRGE -- -- -- AST7 -- WCE7 -- -- SSBY A23E -- -- -- -- IPRA7 IPRB7 -- -- -- -- AD8 AD0 AD8 AD0 AD8 AD0 AD8 AD0 ADIE -- -- -- -- AST6 -- WCE6 -- -- STS2 A22E -- -- -- -- IPRA6 IPRB6 -- -- -- -- AD7 -- AD7 -- AD7 -- AD7 -- ADST -- -- -- -- AST5 -- WCE5 -- -- STS1 A21E IRQ5SC IRQ5E IRQ5F -- -- -- -- -- -- -- AD6 -- AD6 -- AD6 -- AD6 -- SCAN -- -- -- -- AST4 -- WCE4 -- -- STS0 -- IRQ4SC IRQ4E IRQ4F -- IPRA4 -- -- -- -- -- AD5 -- AD5 -- AD5 -- AD5 -- CKS -- -- -- -- AST3 WMS1 WCE3 -- -- UE -- -- -- -- -- IPRA3 IPRB3 -- -- -- -- AD4 -- AD4 -- AD4 -- AD4 -- CH2 -- -- -- -- AST2 WMS0 WCE2 -- MDS2 NMIEG -- -- -- -- -- IPRA2 IPRB2 -- -- -- -- AD3 -- AD3 -- AD3 -- AD3 -- CH1 -- -- -- -- AST1 WC1 WCE1 -- MDS1 -- -- IRQ1SC IRQ1E IRQ1F -- IPRA1 IPRB1 -- -- -- -- AD2 -- AD2 -- AD2 -- AD2 -- CH0 -- -- -- -- AST0 WC0 WCE0 -- MDS0 RAME -- IRQ0SC IRQ0E IRQ0F -- IPRA0 -- -- -- System control Bus controller Interrupt controller Bus controller A/D Data Bus Width 8 Bit Names Bit 7 -- Bit 6 -- Bit 5 -- Bit 4 -- Bit 3 P53PCR Bit 2 P52PCR Bit 1 P51PCR Bit 0 P50PCR Module Name Port 5
Legend A/D: A/D converter
Rev.2.00 Mar. 22, 2007 Page 594 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
B.2
Function
Register name Address to which the register is mapped Name of on-chip supporting module
Register acronym
TSTR Timer Start Register
H'60
ITU (all channels)
Bit numbers
Bit 7 6 5 4 STR4 0 R/W 3 STR3 0 R/W 2 STR2 0 R/W 1 STR1 0 R/W 0 STR0 0 R/W
Initial bit values
--
Initial value Read/Write 1
--
1
--
1
--
--
--
Names of the bits. Dashes (--) indicate reserved bits.
Possible types of access R W Read only Write only
Counter start 0 0 TCNT0 is halted 1 TCNT0 is counting Counter start 1 0 TCNT1 is halted 1 TCNT1 is counting Counter start 2 0 TCNT2 is halted 1 TCNT2 is counting Counter start 3 0 TCNT3 is halted 1 TCNT3 is counting Counter start 4 0 TCNT4 is halted 1 TCNT4 is counting
R/W Read and write
Full name of bit
Descriptions of bit settings
Rev.2.00 Mar. 22, 2007 Page 595 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
FLMCR1--Flash Memory Control Register 1
Bit 7 FWE Initial value Read/Write --* R 6 SWE 0 R/W 5 ESU 0 R/W 4 PSU 0 R/W 3 EV 0 R/W 2 PV 0 R/W
H'40
1 E 0 R/W 0 P 0 R/W
Flash memory
Program mode 0 1 Program mode cleared (Initial value) Transition to program mode [Setting condition] When FWE = 1, SWE = 1, and PSU = 1
Erase mode 0 1 Erase mode cleared (Initial value) Transition to erase mode [Setting condition] When FWE = 1, SWE = 1, and ESU = 1
Program-verify mode 0 1 Program-verify mode cleared (Initial value) Transition to program-verify mode [Setting condition] When FWE = 1 and SWE = 1
Erase-verify mode 0 1 Erase-verify mode cleared (Initial value) Transition to erase-verify mode [Setting condition] When FWE = 1 and SWE = 1
Program setup 0 1 Program setup cleared (Initial value) Program setup [Setting condition] When FWE = 1 and SWE = 1
Erase setup 0 1 Erase setup cleared (Initial value) Erase setup [Setting condition] When FWE = 1 and SWE = 1
Software write enable bit 0 1 Program/erase disabled (Initial value) Program/erase enabled [Setting condition] When FWE = 1
Flash write enable bit 0 1 When a low level is input to the FWE pin (hardware protection state) When a high level is input to the FWE pin
Notes: This register is used only in the flash memory versions. Reading the corresponding address in a mask ROM version will always return 1s, and writes to this address are disabled. * Set according to the state of the FWE pin.
Rev.2.00 Mar. 22, 2007 Page 596 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
FLMCR2--Flash Memory Control Register 2
Bit 7 FLER Initial value Read/Write 0 R 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'41
3 -- 1 -- 2 -- 1 --
Flash memory
1 -- 1 -- 0 -- 1 --
Flash memory error 0 Flash memory write/erase protection is disabled (Initial value) 1 An error has occurred during flash memory writing/erasing Flash memory error protection is enabled
Note : This register is used only in the flash memory versions. Reading the corresponding address in a mask ROM version will always return 1s, and writes to this address are disabled.
EBR1--Erase Block Register 1
Bit 7 EB7 Initial value Read/Write 0 R/W 6 EB6 0 R/W
H'42
5 EB5 0 R/W
Flash memory
4 EB4 0 R/W 3 EB3 0 R/W 2 EB2 0 R/W 1 EB1 0 R/W 0 EB0 0 R/W
Block 7 to 0 0 1 Block EB7 to EB0 is not selected (Initial value) Block EB7 to EB0 is selected
Note: When not erasing, clear all EBR bits to 0. This register is used only in the flash memory versions. Reading the corresponding address in a mask ROM version will always return 1s, and writes to this address are disabled.
Rev.2.00 Mar. 22, 2007 Page 597 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
EBR2--Erase Block Register 2
Bit 7 6 5 4
H'43
3 EB11 0 R/W 2 EB10 0 R/W
Flash memory
1 EB9 0 R/W 0 EB8 0 R/W
--
Initial value Read/Write 0 R
--
0 R
--
0 R
--
0 R
Block 7 to 0 0 1 Block EB8 to EB11 is not selected (Initial value) Block EB8 to EB11 is selected
Note: When not erasing, clear all EBR bits to 0. This register is used only in the flash memory versions. Reading the corresponding address in a mask ROM version will always return 1s, and writes to this address are disabled.
Rev.2.00 Mar. 22, 2007 Page 598 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
RAMER--RAM Emulation Register
Bit 7 -- Initial value R/W 1 R 6 -- 1 R 5 -- 1 R 4 -- 1 R
H'47
3 RAMS 0 R/W 2 RAM2 0 R/W
Flash Memory
1 RAM1 0 R/W 0 RAM0 0 R/W
RAM select, RAM2, RAM1, RAM0 Bit 3 Bit 2 Bit 1 Bit 0 RAM Area H'FFFFE000 to H'FFFFEFFF H'00000000 to H'00000FFF H'00001000 to H'00001FFF H'00002000 to H'00002FFF H'00003000 to H'00003FFF H'00004000 to H'00004FFF H'00005000 to H'00005FFF H'00006000 to H'00006FFF H'00007000 to H'00007FFF
RAMS RAM2 RAM1 RAM0 0 1 * 0 * 0 * 0 1 1 0 1 1 0 0 1 1 0 1 *: Don't care. Note: This register is used only in the flash memory versions. Reading the corresponding address in a mask ROM version will always return 1s, and writes to this address are disabled.
Rev.2.00 Mar. 22, 2007 Page 599 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
DIVCR--Division Control Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 7 -- 1 --
H'5D
3 -- 1 -- 2 -- 1 --
System control
1 DIV1 0 R/W 0 DIV0 0 R/W
Divide bits 1 and 0 Bit 1 Bit 0 Frequency DIV1 DIV0 Division Ratio 0 1/1initial value 0 1 1/2 1/4 0 1 1 1/8
Rev.2.00 Mar. 22, 2007 Page 600 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
MSTCR--Module Standby Control Register
Bit Initial value Read/Write 7 PSTOP 0 R/W 6 -- 1 -- 5 0 R/W 4 0 R/W
H'5E
3 0 R/W 2 -- 0 R/W
System control
1 -- 0 R/W 0 MSTOP0 0 R/W
MSTOP5 MSTOP4 MSTOP3
Module standby 0 0 A/D converter operates normally (Initial value) 1 A/D converter is in standby state Module standby 3 0 SCI1 operates normally (Initial value) 1 SCI1 is in standby state Module standby 4 0 SCI0 operates normally (Initial value) 1 SCI0 is in standby state Module standby 5 0 ITU operates normally (Initial value) 1 ITU is in standby state clock stop 0 clock output is enabled (Initial value) 1 clock output is disabled
Rev.2.00 Mar. 22, 2007 Page 601 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TSTR--Timer Start Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 STR4 0 R/W
H'60
3 STR3 0 R/W 2
ITU (all channels)
1 STR1 0 R/W 0 STR0 0 R/W
STR2 0 R/W
Counter start 0 0 TCNT0 is halted 1 TCNT0 is counting Counter start 1 0 TCNT1 is halted 1 TCNT1 is counting Counter start 2 0 TCNT2 is halted 1 TCNT2 is counting Counter start 3 0 TCNT3 is halted 1 TCNT3 is counting Counter start 4 0 TCNT4 is halted 1 TCNT4 is counting
Rev.2.00 Mar. 22, 2007 Page 602 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TSNC--Timer Synchro Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 SYNC4 0 R/W
H'61
3 SYNC3 0 R/W 2
ITU (all channels)
1 SYNC1 0 R/W 0 SYNC0 0 R/W
SYNC2 0 R/W
Timer sync 0 0 TCNT0 operates independently 1 TCNT0 is synchronized Timer sync 1 0 TCNT1 operates independently 1 TCNT1 is synchronized Timer sync 2 0 TCNT2 operates independently 1 TCNT2 is synchronized Timer sync 3 0 TCNT3 operates independently 1 TCNT3 is synchronized Timer sync 4 0 TCNT4 operates independently 1 TCNT4 is synchronized
Rev.2.00 Mar. 22, 2007 Page 603 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TMDR--Timer Mode Register
Bit Initial value Read/Write 7 -- 1 -- 6 MDF 0 R/W 5 FDIR 0 R/W 4 PWM4 0 R/W
H'62
3 PWM3 0 R/W 2
ITU (all channels)
1 PWM1 0 R/W 0 PWM0 0 R/W
PWM2 0 R/W
PWM mode 0 0 Channel 0 operates normally 1 Channel 0 operates in PWM mode PWM mode 1 0 Channel 1 operates normally 1 Channel 1 operates in PWM mode PWM mode 2 0 Channel 2 operates normally 1 Channel 2 operates in PWM mode PWM mode 3 0 Channel 3 operates normally 1 Channel 3 operates in PWM mode PWM mode 4 0 Channel 4 operates normally 1 Channel 4 operates in PWM mode Flag direction 0 OVF is set to 1 in TSR2 when TCNT2 overflows or underflows 1 OVF is set to 1 in TSR2 when TCNT2 overflows Phase counting mode flag 0 Channel 2 operates normally 1 Channel 2 operates in phase counting mode
Rev.2.00 Mar. 22, 2007 Page 604 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TFCR--Timer Function Control Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 CMD1 0 R/W 4 CMD0 0 R/W
H'63
3 BFB4 0 R/W 2 BFA4 0 R/W
ITU (all channels)
1 BFB3 0 R/W 0 BFA3 0 R/W
Buffer mode A3 0 GRA3 operates normally 1 GRA3 is buffered by BRA3 Buffer mode B3 0 GRB3 operates normally 1 GRB3 is buffered by BRB3 Buffer mode A4 0 GRA4 operates normally 1 GRA4 is buffered by BRA4 Buffer mode B4 0 GRB4 operates normally 1 GRB4 is buffered by BRB4 Combination mode 1 and 0 Bit 5 Bit 4 CMD1 CMD0 Operating Mode of Channels 3 and 4 0 0 Channels 3 and 4 operate normally 1 0 1 Channels 3 and 4 operate together in complementary PWM mode 1 Channels 3 and 4 operate together in reset-synchronized PWM mode
Rev.2.00 Mar. 22, 2007 Page 605 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TCR0--Timer Control Register 0
Bit Initial value Read/Write 7 -- 1 -- 6 CCLR1 0 R/W 5 CCLR0 0 R/W 4 0 R/W
H'64
3 0 R/W 2 TPSC2 0 R/W
ITU0
1 TPSC1 0 R/W 0 TPSC0 0 R/W
CKEG1 CKEG0
Timer prescaler 2 to 0 Bit 0 Bit 2 Bit 1 TPSC2 TPSC1 TPSC0 0 0 0 1 0 1 1 0 0 1 1 0 1 1 Clock edge 1 and 0 Bit 4 Bit 3 CKEG1 CKEG0 0 0 1 1 -- Counted Edges of External Clock Rising edges counted Falling edges counted Both edges counted TCNT Clock Source Internal clock: Internal clock: /2 Internal clock: /4 Internal clock: /8 External clock A: TCLKA input External clock B: TCLKB input External clock C: TCLKC input External clock D: TCLKD input
Counter clear 1 and 0 Bit 6 Bit 5 CCLR1 CCLR0 TCNT Clear Source 0 0 TCNT is not cleared TCNT is cleared by GRA compare match or input capture 1 1 0 TCNT is cleared by GRB compare match or input capture 1 Synchronous clear: TCNT is cleared in synchronization with other synchronized timers
Rev.2.00 Mar. 22, 2007 Page 606 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TIOR0--Timer I/O Control Register 0
Bit Initial value Read/Write 7 -- 1 -- 6 IOB2 0 R/W 5 IOB1 0 R/W 4 IOB0 0 R/W
H'65
3 -- 1 -- 2 IOA2 0 R/W
ITU0
1 IOA1 0 R/W 0 IOA0 0 R/W
I/O control A2 to A0 Bit 2 Bit 1 Bit 0 IOA2 IOA1 IOA0 0 0 0 1 1 0 1 1 0 0 1 1 0 1 I/O control B2 to B0 Bit 6 Bit 5 Bit 4 IOB2 IOB1 IOB0 0 0 0 1 0 1 1 0 1 0 1 0 1 1
GRA Function GRA is an output compare register
GRA is an input capture register
No output at compare match 0 output at GRA compare match 1 output at GRA compare match Output toggles at GRA compare match GRA captures rising edge of input GRA captures falling edge of input GRA captures both edges of input
GRB Function GRB is an output compare register
GRB is an input capture register
No output at compare match 0 output at GRB compare match 1 output at GRB compare match Output toggles at GRB compare match GRB captures rising edge of input GRB captures falling edge of input GRB captures both edges of input
Rev.2.00 Mar. 22, 2007 Page 607 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TIER0--Timer Interrupt Enable Register 0
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'66
3 -- 1 -- 2 OVIE 0 R/W
ITU0
1 IMIEB 0 R/W 0 IMIEA 0 R/W
Input capture/compare match interrupt enable A 0 IMIA interrupt requested by IMFA is disabled 1 IMIA interrupt requested by IMFA is enabled Input capture/compare match interrupt enable B 0 IMIB interrupt requested by IMFB is disabled 1 IMIB interrupt requested by IMFB is enabled Overflow interrupt enable 0 OVI interrupt requested by OVF is disabled 1 OVI interrupt requested by OVF is enabled
Rev.2.00 Mar. 22, 2007 Page 608 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TSR0--Timer Status Register 0
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'67
3 -- 1 -- 2 OVF 0 R/(W)*
ITU0
1 IMFB 0 R/(W)* 0 IMFA 0 R/(W)*
Input capture/compare match flag A 0 [Clearing condition] Read IMFA when IMFA = 1, then write 0 in IMFA 1 [Setting conditions] TCNT = GRA when GRA functions as a compare match register. TCNT value is transferred to GRA by an input capture signal, when GRA functions as an input capture register. Input capture/compare match flag B 0 [Clearing condition] Read IMFB when IMFB = 1, then write 0 in IMFB 1 [Setting conditions] TCNT = GRB when GRB functions as a compare match register. TCNT value is transferred to GRB by an input capture signal, when GRB functions as an input capture register. Overflow flag 0 [Clearing condition] Read OVF when OVF = 1, then write 0 in OVF 1 [Setting condition] TCNT overflowed from H'FFFF to H'0000
Note: * Only 0 can be written to clear the flag.
Rev.2.00 Mar. 22, 2007 Page 609 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TCNT0 H/L--Timer Counter 0 H/L
Bit Initial value Read/Write 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0
H'68, H'69
6 0 5 0 4 0 3 0
ITU0
2 0 1 0 0 0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Up-counter
GRA0 H/L--General Register A0 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'6A, H'6B
6 1 5 1 4 1 3 1
ITU0
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Output compare or input capture register
GRB0 H/L--General Register B0 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'6C, H'6D
6 1 5 1 4 1 3 1
ITU0
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Output compare or input capture register
TCR1--Timer Control Register 1
Bit Initial value Read/Write 7 -- 1 -- 6 CCLR1 0 R/W 5 CCLR0 0 R/W 4 CKEG1 0 R/W
H'6E
3 CKEG0 0 R/W 2 TPSC2 0 R/W
ITU1
1 TPSC1 0 R/W 0 TPSC0 0 R/W
Note: Bit functions are the same as for ITU0.
Rev.2.00 Mar. 22, 2007 Page 610 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TIOR1--Timer I/O Control Register 1
Bit Initial value Read/Write 7 -- 1 -- 6 IOB2 0 R/W 5 IOB1 0 R/W 4 IOB0 0 R/W
H'6F
3 -- 1 -- 2 IOA2 0 R/W
ITU1
1 IOA1 0 R/W 0 IOA0 0 R/W
Note: Bit functions are the same as for ITU0.
TIER1--Timer Interrupt Enable Register 1
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'70
3 -- 1 -- 2 OVIE 0 R/W
ITU1
1 IMIEB 0 R/W 0 IMIEA 0 R/W
Note: Bit functions are the same as for ITU0.
TSR1--Timer Status Register 1
Bit Initial value Read/Write Notes: 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'71
3 -- 1 -- 2 OVF 0 R/(W)*
ITU1
1 IMFB 0 R/(W)* 0 IMFA 0 R/(W)*
Bit functions are the same as for ITU0. * Only 0 can be written to clear the flag.
TCNT1 H/L--Timer Counter 1 H/L
Bit Initial value Read/Write 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0
H'72, H'73
6 0 5 0 4 0 3 0
ITU1
2 0 1 0 0 0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU0.
Rev.2.00 Mar. 22, 2007 Page 611 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
GRA1 H/L--General Register A1 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'74, H'75
6 1 5 1 4 1 3 1
ITU1
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU0.
GRB1 H/L--General Register B1 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'76, H'77
6 1 5 1 4 1 3 1
ITU1
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU0.
TCR2--Timer Control Register 2
Bit Initial value Read/Write 7 -- 1 -- 6 CCLR1 0 R/W 5 CCLR0 0 R/W 4 CKEG1 0 R/W
H'78
3 CKEG0 0 R/W 2 TPSC2 0 R/W 1
ITU2
0 TPSC0 0 R/W
TPSC1 0 R/W
Notes: 1. Bit functions are the same as for ITU0. 2. When channel 2 is used in phase counting mode, the counter clock source selection by bits CKEG1, CKEG0 and TPSC2 to TPSC0 is ignored.
Rev.2.00 Mar. 22, 2007 Page 612 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TIOR2--Timer I/O Control Register 2
Bit Initial value Read/Write 7 -- 1 -- 6 IOB2 0 R/W 5 IOB1 0 R/W 4 IOB0 0 R/W
H'79
3 -- 1 -- 2 IOA2 0 R/W
ITU2
1 IOA1 0 R/W 0 IOA0 0 R/W
Notes: 1. Bit functions are the same as for ITU0. 2. Channel 2 does not have a compare match toggle output function. If this setting is used, 1 output will be selected automatically.
Rev.2.00 Mar. 22, 2007 Page 613 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TIER2--Timer Interrupt Enable Register 2
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'7A
3 -- 1 -- 2 OVIE 0 R/W
ITU2
1 IMIEB 0 R/W 0 IMIEA 0 R/W
Note: Bit functions are the same as for ITU0.
TSR2--Timer Status Register 2
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'7B
3 -- 1 -- 2 OVF 0 R/(W)*
ITU2
1 IMFB 0 R/(W)* 0 IMFA 0 R/(W)*
Overflow flag
Bit functions are the same as for ITU0
0 [Clearing condition] Read OVF when OVF = 1, then write 0 in OVF 1 [Setting condition] TCNT overflowed from H'FFFF to H'0000 or underflowed from H'0000 to H'FFFF Note: * Only 0 can be written to clear the flag.
TCNT2 H/L--Timer Counter 2 H/L
Bit Initial value Read/Write 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0
H'7C, H'7D
6 0 5 0 4 0 3 0
ITU2
2 0 1 0 0 0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Phase counting mode: up/down-counter Other modes: up-counter
Rev.2.00 Mar. 22, 2007 Page 614 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
GRA2 H/L--General Register A2 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'7E, H'7F
6 1 5 1 4 1 3 1
ITU2
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU0.
GRB2 H/L--General Register B2 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'80, H'81
6 1 5 1 4 1 3 1
ITU2
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU0.
TCR3--Timer Control Register 3
Bit Initial value Read/Write 7 -- 1 -- 6 CCLR1 0 R/W 5 CCLR0 0 R/W 4 CKEG1 0 R/W
H'82
3 CLEG0 0 R/W 2 TPSC2 0 R/W
ITU3
1 TPSC1 0 R/W 0 TPSC0 0 R/W
Note: Bit functions are the same as for ITU0.
TIOR3--Timer I/O Control Register 3
Bit Initial value Read/Write 7 -- 1 -- 6 IOB2 0 R/W 5 IOB1 0 R/W 4 IOB0 0 R/W
H'83
3 -- 1 -- 2 IOA2 0 R/W
ITU3
1 IOA1 0 R/W 0 IOA0 0 R/W
Note: Bit functions are the same as for ITU0.
Rev.2.00 Mar. 22, 2007 Page 615 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TIER3--Timer Interrupt Enable Register 3
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'84
3 -- 1 -- 2 OVIE 0 R/W
ITU3
1 IMIEB 0 R/W 0 IMIEA 0 R/W
Note: Bit functions are the same as for ITU0.
TSR3--Timer Status Register 3
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'85
3 -- 1 -- 2 OVF 0 R/(W)*
ITU3
1 IMFB 0 R/(W)* 0 IMFA 0 R/(W)*
Overflow flag
Bit functions are the same as for ITU0
0 [Clearing condition] Read OVF when OVF = 1, then write 0 in OVF 1 [Setting condition] TCNT overflowed from H'FFFF to H'0000 or underflowed from H'0000 to H'FFFF Note: Only 0 can be written to clear the flag.
TCNT3 H/L--Timer Counter 3 H/L
Bit Initial value Read/Write 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0
H'86, H'87
6 0 5 0 4 0 3 0
ITU3
2 0 1 0 0 0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Complementary PWM mode: up/down counter Other modes: up-counter
Rev.2.00 Mar. 22, 2007 Page 616 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
GRA3 H/L--General Register A3 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'88, H'89
6 1 5 1 4 1 3 1
ITU3
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Output compare or input capture register (can be buffered)
GRB3 H/L--General Register B3 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'8A, H'8B
6 1 5 1 4 1 3 1
ITU3
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Output compare or input capture register (can be buffered)
BRA3 H/L--Buffer Register A3 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'8C, H'8D
6 1 5 1 4 1 3 1
ITU3
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Used to buffer GRA
BRB3 H/L--Buffer Register B3 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'8E, H'8F
6 1 5 1 4 1 3 1
ITU3
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Used to buffer GRB
Rev.2.00 Mar. 22, 2007 Page 617 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TOER--Timer Output Master Enable Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 EXB4 1 R/W 4 EXA4 1 R/W 3 EB3 1 R/W
H'90
2 EB4 1 R/W
ITU (all channels)
1 EA4 1 R/W 0 EA3 1 R/W
Master enable TIOCA3 0 TIOCA 3 output is disabled regardless of TIOR3, TMDR, and TFCR settings 1 TIOCA 3 is enabled for output according to TIOR3, TMDR, and TFCR settings Master enable TIOCA4 0 TIOCA 4 output is disabled regardless of TIOR4, TMDR, and TFCR settings 1 TIOCA 4 is enabled for output according to TIOR4, TMDR, and TFCR settings Master enable TIOCB4 0 TIOCB4 output is disabled regardless of TIOR4 and TFCR settings 1 TIOCB4 is enabled for output according to TIOR4 and TFCR settings Master enable TIOCB3 0 TIOCB 3 output is disabled regardless of TIOR3 and TFCR settings 1 TIOCB 3 is enabled for output according to TIOR3 and TFCR settings Master enable TOCXA4 0 TOCXA 4 output is disabled regardless of TFCR settings 1 TOCXA 4 is enabled for output according to TFCR settings Master enable TOCXB4 0 TOCXB4 output is disabled regardless of TFCR settings 1 TOCXB4 is enabled for output according to TFCR settings
Rev.2.00 Mar. 22, 2007 Page 618 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TOCR--Timer Output Control Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 XTGD 1 R/W
H'91
3 -- 1 -- 2 -- 1 --
ITU (all channels)
1 OLS4 1 R/W 0 OLS3 1 R/W
Output level select 3 0 TIOCB 3 , TOCXA 4, and TOCXB 4 outputs are inverted 1 TIOCB 3 , TOCXA 4, and TOCXB 4 outputs are not inverted Output level select 4 0 TIOCA 3 , TIOCA 4, and TIOCB 4 outputs are inverted 1 TIOCA 3 , TIOCA 4, and TIOCB 4 outputs are not inverted External trigger disable 0 Input capture A in channel 1 is used as an external trigger signal in reset-synchronized PWM mode and complementary PWM mode* 1 External triggering is disabled Note: * When an external trigger occurs, bits 5 to 0 in TOER are cleared to 0, disabling ITU output.
Rev.2.00 Mar. 22, 2007 Page 619 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TCR4--Timer Control Register 4
Bit Initial value Read/Write 7 -- 1 -- 6 CCLR1 0 R/W 5 CCLR0 0 R/W 4 CKEG1 0 R/W
H'92
3 CKEG0 0 R/W 2 TPSC2 0 R/W
ITU4
1 TPSC1 0 R/W 0 TPSC0 0 R/W
Note: Bit functions are the same as for ITU0.
TIOR4--Timer I/O Control Register 4
Bit Initial value Read/Write 7 -- 1 -- 6 IOB2 0 R/W 5 IOB1 0 R/W 4 IOB0 0 R/W
H'93
3 -- 1 -- 2 IOA2 0 R/W
ITU4
1 IOA1 0 R/W 0 IOA0 0 R/W
Note: Bit functions are the same as for ITU0.
TIER4--Timer Interrupt Enable Register 4
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'94
3 -- 1 -- 2 OVIE 0 R/W
ITU4
1 IMIEB 0 R/W 0 IMIEA 0 R/W
Note: Bit functions are the same as for ITU0.
TSR4--Timer Status Register 4
Bit Initial value Read/Write Notes: 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'95
3 -- 1 -- 2 OVF 0 R/(W)*
ITU4
1 IMFB 0 R/(W)* 0 IMFA 0 R/(W)*
Bit functions are the same as for ITU0. * Only 0 can be written to clear the flag.
Rev.2.00 Mar. 22, 2007 Page 620 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TCNT4 H/L--Timer Counter 4 H/L
Bit Initial value Read/Write 15 0 14 0 13 0 12 0 11 0 10 0 9 0 8 0 7 0
H'96, H'97
6 0 5 0 4 0 3 0
ITU4
2 0 1 0 0 0
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU3.
GRA4 H/L--General Register A4 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'98, H'99
6 1 5 1 4 1 3 1
ITU4
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU3.
GRB4 H/L--General Register B4 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'9A, H'9B
6 1 5 1 4 1 3 1
ITU4
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU3.
BRA4 H/L--Buffer Register A4 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'9C, H'9D
6 1 5 1 4 1 3 1
ITU4
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU3.
Rev.2.00 Mar. 22, 2007 Page 621 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
BRB4 H/L--Buffer Register B4 H/L
Bit Initial value Read/Write 15 1 14 1 13 1 12 1 11 1 10 1 9 1 8 1 7 1
H'9E, H'9F
6 1 5 1 4 1 3 1
ITU4
2 1 1 1 0 1
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Note: Bit functions are the same as for ITU3.
TPMR--TPC Output Mode Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'A0
3 0 R/W 2 0 R/W
TPC
1 0 R/W 0 0 R/W
G3NOV G2NOV
G1NOV G0NOV
Group 0 non-overlap 0 Normal TPC output in group 0 Output values change at compare match A in the selected ITU channel 1 Non-overlapping TPC output in group 0, controlled by compare match A and B in the selected ITU channel Group 1 non-overlap 0 Normal TPC output in group 1 Output values change at compare match A in the selected ITU channel 1 Non-overlapping TPC output in group 1, controlled by compare match A and B in the selected ITU channel Group 2 non-overlap 0 Normal TPC output in group 2 Output values change at compare match A in the selected ITU channel 1 Non-overlapping TPC output in group 2, controlled by compare match A and B in the selected ITU channel Group 3 non-overlap 0 Normal TPC output in group 3 Output values change at compare match A in the selected ITU channel 1 Non-overlapping TPC output in group 3, controlled by compare match A and B in the selected ITU channel
Rev.2.00 Mar. 22, 2007 Page 622 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TPCR--TPC Output Control Register
Bit Initial value Read/Write 7 1 R/W 6 1 R/W 5 1 R/W 4 1 R/W
H'A1
3 1 R/W 2 1 R/W 1 1 R/W
TPC
0 1 R/W
G3CMS1 G3CMS0 G2CMS1 G2CMS0 G1CMS1 G1CMS0 G0CMS1 G0CMS0
Group 0 compare match select 1 and 0 Bit 1 Bit 0 G0CMS1 G0CMS0 0 0 1 1 0 1 ITU Channel Selected as Output Trigger TPC output group 0 (TP3 to TP 0) is triggered by compare match in ITU channel 0 TPC output group 0 (TP3 to TP 0) is triggered by compare match in ITU channel 1 TPC output group 0 (TP3 to TP 0) is triggered by compare match in ITU channel 2 TPC output group 0 (TP3 to TP 0) is triggered by compare match in ITU channel 3
Group 1 compare match select 1 and 0 Bit 3 Bit 2 G1CMS1 G1CMS0 0 0 1 1 0 1 ITU Channel Selected as Output Trigger TPC output group 1 (TP7 to TP4 ) is triggered by compare match in ITU channel 0 TPC output group 1 (TP7 to TP4 ) is triggered by compare match in ITU channel 1 TPC output group 1 (TP7 to TP4 ) is triggered by compare match in ITU channel 2 TPC output group 1 (TP7 to TP4 ) is triggered by compare match in ITU channel 3
Group 2 compare match select 1 and 0 Bit 5 Bit 4 G2CMS1 G2CMS0 0 0 1 1 0 1 ITU Channel Selected as Output Trigger TPC output group 2 (TP11 to TP8) is triggered by compare match in ITU channel 0 TPC output group 2 (TP11 to TP8) is triggered by compare match in ITU channel 1 TPC output group 2 (TP11 to TP8) is triggered by compare match in ITU channel 2 TPC output group 2 (TP11 to TP8) is triggered by compare match in ITU channel 3
Group 3 compare match select 1 and 0 Bit 7 Bit 6 G3CMS1 G3CMS0 0 0 1 0 1 1 ITU Channel Selected as Output Trigger TPC output group 3 (TP15 to TP12)* is triggered by compare match in ITU channel 0 TPC output group 3 (TP15 to TP12)* is triggered by compare match in ITU channel 1 TPC output group 3 (TP15 to TP12)* is triggered by compare match in ITU channel 2 TPC output group 3 (TP15 to TP12)* is triggered by compare match in ITU channel 3
Note: * Since this LSI does not have a TP14 pin, the TP14 signal cannot be output off-chip.
Rev.2.00 Mar. 22, 2007 Page 623 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
NDERB--Next Data Enable Register B
Bit Initial value Read/Write 7 0 R/W 6 0 R/W 5 0 R/W 4 0 R/W
H'A2
3 0 R/W 2 0 R/W
TPC
1 0 R/W 0 NDER8 0 R/W
NDER15 NDER14 NDER13 NDER12 NDER11 NDER10 NDER9
Next data enable 15 to 8 Bits 7 to 0 NDER15 to NDER8 Description 0 TPC outputs TP15 to TP 8* are disabled (NDR15 to NDR8 are not transferred to PB 7 to PB 0 ) TPC outputs TP15 to TP 8* are enabled 1 (NDR15 to NDR8 are transferred to PB 7 to PB 0 ) Note: * Since this LSI does not have a TP14 pin, the TP14 signal cannot be output off-chip.
NDERA--Next Data Enable Register A
Bit Initial value Read/Write 7 NDER7 0 R/W 6 NDER6 0 R/W 5 NDER5 0 R/W 4 NDER4 0 R/W
H'A3
3 NDER3 0 R/W 2 NDER2 0 R/W
TPC
1 NDER1 0 R/W 0 NDER0 0 R/W
Next data enable 7 to 0 Bits 7 to 0 NDER7 to NDER0 Description 0 TPC outputs TP 7 to TP 0 are disabled (NDR7 to NDR0 are not transferred to PA 7 to PA 0) 1 TPC outputs TP 7 to TP 0 are enabled (NDR7 to NDR0 are transferred to PA 7 to PA 0)
Rev.2.00 Mar. 22, 2007 Page 624 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
NDRB--Next Data Register B * Same output trigger for TPC output groups 2 and 3 Address H'FFA4
Bit Initial value Read/Write 7 NDR15 0 R/W 6 NDR14 0 R/W 5 NDR13 0 R/W 4 NDR12 0 R/W
H'A4/H'A6
TPC
3 NDR11 0 R/W
2 NDR10 0 R/W
1 NDR9 0 R/W
0 NDR8 0 R/W
Next output data for TPC output group 3*
Next output data for TPC output group 2
Address H'FFA6
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 -- 1 -- 2 -- 1 -- 1 -- 1 -- 0 -- 1 --
* Different output triggers for TPC output groups 2 and 3 Address H'FFA4
Bit Initial value Read/Write 7 NDR15 0 R/W 6 NDR14 0 R/W 5 NDR13 0 R/W 4 NDR12 0 R/W 3 -- 1 -- 2 -- 1 -- 1 -- 1 -- 0 -- 1 --
Next output data for TPC output group 3*
Address H'FFA6
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 NDR11 0 R/W 2 NDR10 0 R/W 1 NDR9 0 R/W 0 NDR8 0 R/W
Next output data for TPC output group 2
Note: * Since this LSI does not have a TP14 pin, the TP14 signal cannot be output off-chip. Rev.2.00 Mar. 22, 2007 Page 625 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
NDRA--Next Data Register A * Same output trigger for TPC output groups 0 and 1 Address H'FFA5
Bit Initial value Read/Write 7 NDR7 0 R/W 6 NDR6 0 R/W 5 NDR5 0 R/W 4 NDR4 0 R/W
H'A5/H'A7
TPC
3 NDR3 0 R/W
2 NDR2 0 R/W
1 NDR1 0 R/W
0 NDR0 0 R/W
Next output data for TPC output group 1
Next output data for TPC output group 0
Address H'FFA7
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 -- 1 -- 2 -- 1 -- 1 -- 1 -- 0 -- 1 --
* Different output triggers for TPC output groups 0 and 1 Address H'FFA5
Bit Initial value Read/Write 7 NDR7 0 R/W 6 NDR6 0 R/W 5 NDR5 0 R/W 4 NDR4 0 R/W 3 -- 1 -- 2 -- 1 -- 1 -- 1 -- 0 -- 1 --
Next output data for TPC output group 1
Address H'FFA7
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 -- 3 NDR3 0 R/W 2 NDR2 0 R/W 1 NDR1 0 R/W 0 NDR0 0 R/W
Next output data for TPC output group 0
Rev.2.00 Mar. 22, 2007 Page 626 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TCSR--Timer Control/Status Register
Bit Initial value Read/Write 7 OVF 0 R/(W)* 6 WT/ IT 0 R/W 5 TME 0 R/W 4 -- 1 --
H'A8
3 -- 1 -- 2 CKS2 0 R/W
WDT
1 CKS1 0 R/W 0 CKS0 0 R/W
Timer enable 0 TCNT is initialized to H'00 and halted 1 TCNT is counting
Timer mode select 0 Interval timer: requests interval timer interrupts 1 Watchdog timer: generates a reset signal Overflow flag 0 [Clearing condition] Read OVF when OVF = 1, then write 0 in OVF 1 [Setting condition] TCNT changes from H'FF to H'00
Clock select 2 to 0 CKS2 CKS1 CKS0 0 0 0 1 0 1 1 0 0 1 1 0 1 1
Description /2 /32 /64 /128 /256 /512 /2048 /4096
Note: * Only 0 can be written to clear the flag.
Rev.2.00 Mar. 22, 2007 Page 627 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TCNT--Timer Counter
H'A9 (read), H'A8 (write)
6 0 R/W 5 0 R/W 4 0 R/W 3 0 R/W 2 0 R/W
WDT
Bit Initial value Read/Write
7 0 R/W
1 0 R/W
0 0 R/W
Count value
RSTCSR--Reset Control/Status Register
H'AB (read), H'AA (write)
4 -- 1 -- 3 -- 1 -- 2 -- 1 --
WDT
Bit Initial value Read/Write
7 WRST 0 R/(W)*
6 RSTOE 0 R/W
5 -- 1 --
1 -- 1 --
0 -- 1 --
Reset output enable 0 Reset signal is not output externally 1 Reset signal is output externally Watchdog timer reset 0 [Clearing condition] Reset signal input at RES pin, or 0 written by software 1 [Setting condition] TCNT overflow generates a reset signal Note: * Only 0 can be written in bit 7 to clear the flag.
Rev.2.00 Mar. 22, 2007 Page 628 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
SMR--Serial Mode Register
Bit Initial value Read/Write 7 C/ A 0 R/W 6 CHR 0 R/W 5 PE 0 R/W 7 O/ E 0 R/W
H'B0
3 STOP 0 R/W 2 MP 0 R/W
SCI0
1 CKS1 0 R/W 0 CKS0 0 R/W
Multiprocessor mode 0 Multiprocessor function disabled 1 Multiprocessor format selected Stop bit length 0 One stop bit 1 Two stop bits Parity mode 0 Even parity 1 Odd parity Parity enable 0 Parity bit is not added or checked 1 Parity bit is added and checked Character length 0 8-bit data 1 7-bit data Communication mode 0 Asynchronous mode 1 Synchronous mode
Clock select 1 and 0 Bit 1 Bit 0 CKS1 CKS0 Clock Source 0 0 clock 1 /4 clock 0 1 /16 clock 1 /64 clock
Rev.2.00 Mar. 22, 2007 Page 629 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
BRR--Bit Rate Register
Bit Initial value Read/Write 7 1 R/W 6 1 R/W 5 1 R/W 4 1 R/W
H'B1
3 1 R/W 2 1 R/W
SCI0
1 1 R/W 0 1 R/W
Serial communication bit rate setting
Rev.2.00 Mar. 22, 2007 Page 630 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
SCR--Serial Control Register
Bit Initial value Read/Write 7 TIE 0 R/W 6 RIE 0 R/W 5 TE 0 R/W 4 RE 0 R/W
H'B2
3 MPIE 0 R/W 2 TEIE 0 R/W
SCI0
1 CKE1 0 R/W 0 CKE0 0 R/W
Clock enable 1 and 0 Bit 1 Bit 2 CKE1 CKE2 Clock Selection and Output 0 Asynchronous mode Internal clock, SCK pin available for generic input/output 0 Synchronous mode Internal clock, SCK pin used for serial clock output Asynchronous mode Internal clock, SCK pin used for clock output 1 Synchronous mode Internal clock, SCK pin used for serial clock output Asynchronous mode External clock, SCK pin used for clock input 0 1 Synchronous mode External clock, SCK pin used for serial clock input Asynchronous mode External clock, SCK pin used for clock input 1 Synchronous mode External clock, SCK pin used for serial clock input Transmit-end interrupt enable 0 Transmit-end interrupt requests (TEI) are disabled 1 Transmit-end interrupt requests (TEI) are enabled Multiprocessor interrupt enable 0 Multiprocessor interrupts are disabled (normal receive operation) 1 Multiprocessor interrupts are enabled Transmit enable 0 Transmitting is disabled 1 Transmitting is enabled Receive enable 0 Receiving is disabled 1 Receiving is enabled
Receive interrupt enable 0 Receive-data-full (RXI) and receive-error (ERI) interrupt requests are disabled 1 Receive-data-full (RXI) and receive-error (ERI) interrupt requests are enabled Transmit interrupt enable 0 Transmit-data-empty interrupt request (TXI) is disabled 1 Transmit-data-empty interrupt request (TXI) is enabled
Rev.2.00 Mar. 22, 2007 Page 631 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
TDR--Transmit Data Register
Bit Initial value Read/Write 7 1 R/W 6 1 R/W 5 1 R/W 4 1 R/W
H'B3
3 1 R/W 2 1 R/W
SCI0
1 1 R/W 0 1 R/W
Serial transmit data
Rev.2.00 Mar. 22, 2007 Page 632 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
SSR--Serial Status Register
Bit Initial value Read/Write 7 TDRE 1 R/(W)* 6 RDRF 0 R/(W)* 5 ORER 0 R/(W)* 4 FER 0 R/(W)*
H'B4
3 PER 0 R/(W)* 2 TEND 1 R 1
SCI0
0 MPBT 0 R/W
MPB 0 R
Multiprocessor bit 0 Multiprocessor bit value in receive data is 0 1 Transmit end 0 1 Multiprocessor bit value in receive data is 1
Multiprocessor bit transfer 0 Multiprocessor bit value in transmit data is 0 1 Multiprocessor bit value in transmit data is 1
[Clearing conditions] Read TDRE when TDRE = 1, then write 0 in TDRE. [Setting conditions] Reset or transition to standby mode. TE is cleared to 0 in SCR. TDRE is 1 when last bit of serial character is transmitted. Parity error 0 [Clearing conditions] Reset or transition to standby mode. Read PER when PER = 1, then write 0 in PER. [Setting condition] Parity error: (parity of receive data does not match parity setting of O/ E in SMR) [Clearing conditions] Reset or transition to standby mode. Read ORER when ORER = 1, then write 0 in ORER. [Setting condition] Overrun error (reception of next serial data ends when RDRF = 1)
Framing error 0 [Clearing conditions] Reset or transition to standby mode. Read FER when FER = 1, then write 0 in FER. [Setting condition] Framing error (stop bit is 0)
1
1
Overrun error Receive data register full 0 [Clearing conditions] Reset or transition to standby mode. Read RDRF when RDRF = 1, then write 0 in RDRF. [Setting condition] Serial data is received normally and transferred from RSR to RDR 0
1
1
Transmit data register empty 0 1 [Clearing conditions] Read TDRE when TDRE = 1, then write 0 in TDRE. [Setting conditions] Reset or transition to standby mode. TE is 0 in SCR Data is transferred from TDR to TSR, enabling new data to be written in TDR.
Note: * Only 0 can be written to clear the flag.
Rev.2.00 Mar. 22, 2007 Page 633 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
RDR--Receive Data Register
Bit Initial value Read/Write 7 0 R 6 0 R 5 0 R 4 0 R
H'B5
3 0 R 2 0 R
SCI0
1 0 R 0 0 R
Serial receive data
SCMR--Smart Card Mode Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'B6
3 SDIR 0 R/W 2 SINV 0 R/W
SCI0
1 -- 1 -- 0 SMIF 0 R/W
Smart card interface mode select 0 Smart card interface function is disabled (Initial value) 1 Smart card interface function is enabled Smart card data invert 0 Unmodified TDR contents are transmitted Received data is stored unmodified in RDR
(Initial value)
1 Inverted 1/0 logic levels of TDR contents are transmitted 1/0 logic levels of received data are inverted before storage in RDR Smart card data transfer direction 0 TDR contents are transmitted LSB-first Received data is stored LSB-first in RDR 1 TDR contents are transmitted MSB-first Received data is stored MSB-first in RDR
(Initial value)
Rev.2.00 Mar. 22, 2007 Page 634 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
SMR--Serial Mode Register
Bit Initial value Read/Write 7 C/ A 0 R/W 6 CHR 0 R/W 5 PE 0 R/W 7 O/ E 0 R/W
H'B8
3 STOP 0 R/W 2 MP 0 R/W
SCI1
1 CKS1 0 R/W 0 CKS0 0 R/W
Note: Bit functions are the same as for SCI0.
BRR--Bit Rate Register
Bit Initial value Read/Write 7 1 R/W 6 1 R/W 5 1 R/W 4 1 R/W
H'B9
3 1 R/W 2 1 R/W
SCI1
1 1 R/W 0 1 R/W
Note: Bit functions are the same as for SCI0.
SCR--Serial Control Register
Bit Initial value Read/Write 7 TIE 0 R/W 6 RIE 0 R/W 5 TE 0 R/W 4 RE 0 R/W
H'BA
3 MPIE 0 R/W 2 TEIE 0 R/W
SCI1
1 CKE1 0 R/W 0 CKE0 0 R/W
Note: Bit functions are the same as for SCI0.
TDR--Transmit Data Register
Bit Initial value Read/Write 7 1 R/W 6 1 R/W 5 1 R/W 4 1 R/W
H'BB
3 1 R/W 2 1 R/W
SCI1
1 1 R/W 0 1 R/W
Note: Bit functions are the same as for SCI0.
SSR--Serial Status Register
Bit Initial value Read/Write 7 TDRE 1 R/(W) * 6 RDRF 0 R/(W) * 5 ORER 0 R/(W) * 4 FER 0 R/(W) *
H'BC
3 PER 0 R/(W) * 2 TEND 1 R
SCI1
1 MPB 0 R 0 MPBT 0 R/W
Notes: Bit functions are the same as for SCI0. * Only 0 can be written to clear the flag. Rev.2.00 Mar. 22, 2007 Page 635 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
RDR--Receive Data Register
Bit Initial value Read/Write 7 0 R 6 0 R 5 0 R 4 0 R
H'BD
3 0 R 2 0 R
SCI1
1 0 R 0 0 R
Note: Bit functions are the same as for SCI0.
P1DDR--Port 1 Data Direction Register
Bit Modes Initial value 1 and 3 Read/Write Modes Initial value 5 to 7 Read/Write 7 1 -- 0 W 6 1 -- 0 W 5 1 -- 0 W 4 1 -- 0 W
H'C0
3 1 -- 0 W 2 1 -- 0 W
Port 1
1 1 -- 0 W 0 1 -- 0 W
P17 DDR P16 DDR P15 DDR P14 DDR P13 DDR P12 DDR P11 DDR P10 DDR
Port 1 input/output select 0 Generic input pin 1 Generic output pin
P2DDR--Port 2 Data Direction Register
Bit Modes Initial value 1 and 3 Read/Write Modes Initial value 5 to 7 Read/Write 7 1 -- 0 W 6 1 -- 0 W 5 1 -- 0 W 4 1 -- 0 W
H'C1
3 1 -- 0 W 2 1 -- 0 W
Port 2
1 1 -- 0 W 0 1 -- 0 W
P27 DDR P26 DDR P25 DDR P24 DDR P23 DDR P22 DDR P21 DDR P20 DDR
Port 2 input/output select 0 Generic input pin 1 Generic output pin
Rev.2.00 Mar. 22, 2007 Page 636 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
P1DR--Port 1 Data Register
Bit Initial value Read/Write 7 P17 0 R/W 6 P16 0 R/W 5 P15 0 R/W 4 P14 0 R/W
H'C2
3 P13 0 R/W 2 P12 0 R/W
Port 1
1 P11 0 R/W 0 P10 0 R/W
Data for port 1 pins
P2DR--Port 2 Data Register
Bit Initial value Read/Write 7 P27 0 R/W 6 P26 0 R/W 5 P25 0 R/W 4 P24 0 R/W
H'C3
3 P23 0 R/W 2 P22 0 R/W
Port 2
1 P21 0 R/W 0 P20 0 R/W
Data for port 2 pins
P3DDR--Port 3 Data Direction Register
Bit Initial value Read/Write 7 0 W 6 0 W 5 0 W 4 0 W
H'C4
3 0 W 2 0 W
Port 3
1 0 W 0 0 W
P3 7 DDR P3 6 DDR P3 5 DDR P3 4 DDR P3 3 DDR P3 2 DDR P3 1 DDR P3 0 DDR
Port 3 input/output select 0 Generic input pin 1 Generic output pin
Rev.2.00 Mar. 22, 2007 Page 637 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
P3DR--Port 3 Data Register
Bit Initial value Read/Write 7 P3 7 0 R/W 6 P3 6 0 R/W 5 P3 5 0 R/W 4 P3 4 0 R/W
H'C6
3 P3 3 0 R/W 2 P3 2 0 R/W
Port 3
1 P3 1 0 R/W 0 P3 0 0 R/W
Data for port 3 pins
P5DDR--Port 5 Data Direction Register
Bit Modes Initial value 1 and 3 Read/Write Modes 5 to 7 Initial value Read/Write 7 -- 1 -- 1 -- 6 -- 1 -- 1 -- 5 -- 1 -- 1 -- 4 -- 1 -- 1 --
H'C8
3 1 -- 0 W 2 1 -- 0 W
Port 5
1 1 -- 0 W 0 1 -- 0 W
P5 3 DDR P5 2 DDR P5 1 DDR P5 0 DDR
Port 5 input/output select 0 Generic input 1 Generic output
Rev.2.00 Mar. 22, 2007 Page 638 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
P6DDR--Port 6 Data Direction Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 0 W 5 0 W 4 0 W
H'C9
3 0 W 2 -- 0 W
Port 6
1 -- 0 W 0 P6 0 DDR 0 W
P6 5 DDR P6 4 DDR P6 3 DDR
Port 6 input/output select 0 Generic input 1 Generic output
P5DR--Port 5 Data Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'CA
3 P53 0 R/W 2 P52 0 R/W
Port 5
1 P51 0 R/W 0 P50 0 R/W
Data for port 5 pins
P6DR--Port 6 Data Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 0 R/W 5 P6 5 0 R/W 4 P6 4 0 R/W
H'CB
3 P6 3 0 R/W 2 -- 0 R/W
Port 6
1 -- 0 R/W 0 P6 0 0 R/W
Data for port 6 pins
Rev.2.00 Mar. 22, 2007 Page 639 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
P8DDR--Port 8 Data Direction Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 0 W
H'CD
3 -- 0 W 2 -- 0 W
Port 8
1 0 W 0 0 W
P8 1 DDR P8 0 DDR
Port 8 input/output select 0 Generic input 1 Generic output
P7DR--Port 7 Data Register
Bit Initial value Read/Write 7 P77 --* R 6 P76 --* R 5 P75 --* R 4 P74 --* R
H'CE
3 P73 --* R 2 P72 --* R
Port 7
1 P71 --* R 0 P70 --* R
The port 7 pin states are read from these bits
Note: * Determined by pins P77 to P70 .
P8DR--Port 8 Data Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 0 R/W
H'CF
3 -- 0 R/W 2 -- 0 R/W
Port 8
1 P8 1 0 R/W 0 P8 0 0 R/W
Data for port 8 pins
Rev.2.00 Mar. 22, 2007 Page 640 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
P9DDR--Port 9 Data Direction Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 0 W 4 0 W
H'D0
3 0 W 2 0 W
Port 9
1 0 W 0 0 W
P95DDR P9 4 DDR P93DDR P9 2 DDR P91DDR P9 0 DDR
Port 9 input/output select 0 Generic input 1 Generic output
PADDR--Port A Data Direction Register
Bit Initial value Read/Write Initial value Read/Write 7 1 -- 0 W 6 0 W 0 W 5 0 W 0 W 4 0 W 0 W
H'D1
3 0 W 0 W 2 0 W 0 W
Port A
1 0 W 0 W 0 0 W 0 W
PA 7 DDR PA 6 DDR PA 5 DDR PA 4 DDR PA 3 DDR PA 2 DDR PA 1 DDR PA 0 DDR Modes 3 and 6 Modes 1, 5 and 7
Port A input/output select 0 Generic input 1 Generic output
P9DR--Port 9 Data Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 P95 0 R/W 4 P94 0 R/W
H'D2
3 P93 0 R/W 2 P92 0 R/W
Port 9
1 P91 0 R/W 0 P90 0 R/W
Data for port 9 pins
Rev.2.00 Mar. 22, 2007 Page 641 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
PADR--Port A Data Register
Bit Initial value Read/Write 7 PA 7 0 R/W 6 PA 6 0 R/W 5 PA 5 0 R/W 4 PA 4 0 R/W
H'D3
3 PA 3 0 R/W 2 PA 2 0 R/W
Port A
1 PA 1 0 R/W 0 PA 0 0 R/W
Data for port A pins
PBDDR--Port B Data Direction Register
Bit Initial value Read/Write 7 PB7 DDR 0 W 6 -- 0 W 5 0 W 4 0 W
H'D4
3 0 W 2 0 W
Port B
1 0 W 0 0 W
PB5 DDR PB4 DDR PB3 DDR PB2 DDR PB1 DDR PB0 DDR
Port B input/output select 0 Generic input 1 Generic output
PBDR--Port B Data Register
Bit Initial value Read/Write 7 PB 7 0 R/W 6 -- 0 R/W 5 PB 5 0 R/W 4 PB 4 0 R/W
H'D6
3 PB 3 0 R/W 2 PB 2 0 R/W
Port B
1 PB 1 0 R/W 0 PB 0 0 R/W
Data for port B pins
Rev.2.00 Mar. 22, 2007 Page 642 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
P2PCR--Port 2 Input Pull-Up MOS Control Register
Bit Initial value Read/Write 7 0 R/W 6 0 R/W 5 0 R/W 4 0 R/W
H'D8
3 0 R/W 2 0 R/W
Port 2
1 0 R/W 0 0 R/W
P2 7 PCR P2 6 PCR P2 5 PCR P2 4 PCR P2 3 PCR P2 2 PCR P2 1 PCR P2 0 PCR
Port 2 input pull-up control 7 to 0 0 Input pull-up transistor is off 1 Input pull-up transistor is on Note: Valid when the corresponding P2DDR bit is cleared to 0 (designating generic input).
P5PCR--Port 5 Input Pull-Up MOS Control Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'DB
3 0 R/W 2 0 R/W
Port 5
1 0 R/W 0 0 R/W
P5 3 PCR P5 2 PCR P5 1 PCR P5 0 PCR
Port 5 input pull-up control 3 to 0 0 Input pull-up transistor is off 1 Input pull-up transistor is on Note: Valid when the corresponding P5DDR bit is cleared to 0 (designating generic input).
ADDRA H/L--A/D Data Register A H/L
Bit Initial value Read/Write 15 0 R 14 0 R 13 0 R 12 0 R 11 0 R 10 0 R 9 0 R 8 0 R 7 0 R
H'E0, H'E1
6 0 R 5 0 R 4 -- 0 R 3 -- 0 R
A/D
2 -- 0 R 1 -- 0 R 0 -- 0 R
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 --
ADDRAH A/D conversion data 10-bit data giving an A/D conversion result
ADDRAL
Rev.2.00 Mar. 22, 2007 Page 643 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
ADDRB H/L--A/D Data Register B H/L
Bit Initial value Read/Write 15 0 R 14 0 R 13 0 R 12 0 R 11 0 R 10 0 R 9 0 R 8 0 R 7 0 R
H'E2, H'E3
6 0 R 5 0 R 4 -- 0 R 3 -- 0 R
A/D
2 -- 0 R 1 -- 0 R 0 -- 0 R
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 --
ADDRBH A/D conversion data 10-bit data giving an A/D conversion result
ADDRBL
ADDRC H/L--A/D Data Register C H/L
Bit Initial value Read/Write 15 0 R 14 0 R 13 0 R 12 0 R 11 0 R 10 0 R 9 0 R 8 0 R 7 0 R
H'E4, H'E5
6 0 R 5 0 R 4 -- 0 R 3 -- 0 R
A/D
2 -- 0 R 1 -- 0 R 0 -- 0 R
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 --
ADDRCH A/D conversion data 10-bit data giving an A/D conversion result
ADDRCL
ADDRD H/L--A/D Data Register D H/L
Bit Initial value Read/Write 15 0 R 14 0 R 13 0 R 12 0 R 11 0 R 10 0 R 9 0 R 8 0 R 7 0 R
H'E6, H'E7
6 0 R 5 0 R 4 -- 0 R 3 -- 0 R
A/D
2 -- 0 R 1 -- 0 R 0 -- 0 R
AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 --
ADDRDH A/D conversion data 10-bit data giving an A/D conversion result
ADDRDL
Rev.2.00 Mar. 22, 2007 Page 644 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
ADCR--A/D Control Register
Bit Initial value Read/Write 7 TRGE 0 R/W 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'E9
3 -- 1 -- 2 -- 1 --
A/D
1 -- 1 -- 0 -- 1 --
Trigger enable 0 A/D conversion cannot be externally triggered 1 A/D conversion starts at the fall of the external trigger signal ( ADTRG )
Rev.2.00 Mar. 22, 2007 Page 645 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
ADCSR--A/D Control/Status Register
Bit Initial value Read/Write 7 ADF 0 R/(W)* 6 ADIE 0 R/W 5 ADST 0 R/W 4 SCAN 0 R/W
H'E8
3 CKS 0 R/W 2 CH2 0 R/W 1 CH1 0 R/W
A/D
0 CH0 0 R/W
Clock select 0 Conversion time = 266 states (maximum) 1 Conversion time = 134 states (maximum) Channel select 2 to 0 Group Channel Selection Selection CH2 CH1 CH0 0 0 0 1 0 1 1 0 1 0 1 0 1 1
Scan mode 0 Single mode 1 Scan mode
Description Single Mode Scan Mode AN 0 AN 0 AN 0, AN 1 AN 1 AN 0 to AN 2 AN 2 AN 0 to AN 3 AN 3 AN 4 AN 4 AN 4, AN 5 AN 5 AN 6 AN 4 to AN 6 AN 7 AN 4 to AN 7
A/D start 0 A/D conversion is stopped 1 Single mode: A/D conversion starts; ADST is automatically cleared to 0 when conversion ends Scan mode: A/D conversion starts and continues, cycling among the selected channels, until ADST is cleared to 0 by software, by a reset, or by a transition to standby mode A/D interrupt enable 0 A/D end interrupt request is disabled 1 A/D end interrupt request is enabled A/D end flag 0 [Clearing condition] Read ADF while ADF = 1, then write 0 in ADF 1 [Setting conditions] Single mode: A/D conversion ends Scan mode: A/D conversion ends in all selected channels Note: * Only 0 can be written to clear flag.
Rev.2.00 Mar. 22, 2007 Page 646 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
ASTCR--Access State Control Register
Bit Initial value Read/Write 7 AST7 1 R/W 6 AST6 1 R/W 5 AST5 1 R/W 4 AST4 1 R/W
H'ED
3 AST3 1 R/W 2 AST2 1 R/W
Bus controller
1 AST1 1 R/W 0 AST0 1 R/W
Area 7 to 0 access state control Bits 7 to 0 Number of States in Access Cycle AST7 to AST0 0 Areas 7 to 0 are two-state access areas 1 Areas 7 to 0 are three-state access areas
WCR--Wait Control Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 1 -- 4 -- 1 --
H'EE
3 WMS1 0 R/W 2 WMS0 0 R/W
Bus controller
1 WC1 1 R/W 0 WC0 1 R/W
Wait mode select 1 and 0 Bit 3 Bit 2 WMS1 WMS0 Wait Mode 0 0 Programmable wait mode 1 No wait states inserted by wait-state controller 1 0 1 Pin wait mode 1 Pin auto-wait mode
Wait count 1 and 0 Bit 1 Bit 0 WC1 WC0 Number of Wait States 0 0 No wait states inserted by wait-state controller 1 1 0 1 1 state inserted 2 states inserted 3 states inserted
Rev.2.00 Mar. 22, 2007 Page 647 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
WCER--Wait Controller Enable Register
Bit Initial value Read/Write 7 WCE7 1 R/W 6 WCE6 1 R/W 5 WCE5 1 R/W 4 WCE4 1 R/W
H'EF
3 WCE3 1 R/W 2 WCE2 1 R/W
Bus controller
1 WCE1 1 R/W 0 WCE0 1 R/W
Wait state controller enable 7 to 0 0 Wait-state control is disabled (pin wait mode 0) 1 Wait-state control is enabled
MDCR--Mode Control Register
Bit Initial value Read/Write 7 -- 1 -- 6 -- 1 -- 5 -- 0 -- 4 -- 0 --
H'F1
3 -- 0 -- 2 MDS2 --* R
System control
1 MDS1 --* R 0 MDS0 --* R
Mode select 2 to 0 Bit 1 Bit 0 Bit 2 MD1 MD0 MD2 0 0 1 0 0 1 1 0 0 1 1 1 0 1 Note: * Determined by the state of the mode pins (MD2 to MD0).
Operating mode -- Mode 1 -- Mode 3 -- Mode 5 Mode 6 Mode 7
Rev.2.00 Mar. 22, 2007 Page 648 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
SYSCR--System Control Register
Bit Initial value Read/Write 7 SSBY 0 R/W 6 STS2 0 R/W 5 STS1 0 R/W 4 STS0 0 R/W 3
H'F2
2 NMIEG 0 R/W 1 -- 1 --
System control
0 RAME 1 R/W
UE 1 R/W
RAM enable 0 On-chip RAM is disabled 1 On-chip RAM is enabled NMI edge select 0 An interrupt is requested at the falling edge of NMI 1 An interrupt is requested at the rising edge of NMI User bit enable 0 CCR bit 6 (UI) is used as an interrupt mask bit 1 CCR bit 6 (UI) is used as a user bit Standby timer select 2 to 0 Bit 6 Bit 5 Bit 4 STS2 STS1 STS0 Standby Timer 0 0 0 Waiting time = 8192 states 1 Waiting time = 16384 states 0 Waiting time = 32768 states 1 1 Waiting time = 65536 states Waiting time = 131072 states 0 1 -- -- Illegal setting 1 Software standby 0 SLEEP instruction causes transition to sleep mode 1 SLEEP instruction causes transition to software standby mode
Rev.2.00 Mar. 22, 2007 Page 649 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
ADRCR--Address Control Register
Bit Modes 1 and 5 to 7 Mode 3 Initial value Read/Write Initial value Read/Write 7 A23E 1 -- 1 R/W 6 A22E 1 -- 1 R/W 5 A21E 1 -- 1 R/W 4 -- 1 -- 1 --
H'F3
3 -- 1 -- 1 -- 2 -- 1 -- 1 --
Bus controller
1 -- 1 -- 1 -- 0 -- 0 R/W 0 R/W
Address 23 to 21 enable 0 Address output 1 I/O pins other than the above
Rev.2.00 Mar. 22, 2007 Page 650 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
ISCR--IRQ Sense Control Register
Bit Initial value Read/Write 7 -- 0 R/W 6 -- 0 R/W 5 0 R/W 4 0 R/W
H'F4
3 -- 0 R/W 2 -- 0 R/W
Interrupt controller
1 0 R/W 0 0 R/W
IRQ5SC IRQ4SC
IRQ1SC IRQ0SC
IRQ 5 , IRQ 4 , IRQ1 and IRQ 0 sense control 0 Interrupts are requested when IRQ 5 , IRQ 4 , IRQ1 , and IRQ 0 inputs are low 1 Interrupts are requested by falling-edge input at IRQ5 , IRQ4 , IRQ1 and IRQ 0
IER--IRQ Enable Register
Bit Initial value Read/Write 7 -- 0 R/W 6 -- 0 R/W 5 IRQ5E 0 R/W 4 IRQ4E 0 R/W
H'F5
3 -- 0 R/W 2 -- 0 R/W
Interrupt controller
1 IRQ1E 0 R/W 0 IRQ0E 0 R/W
IRQ5, IRQ4, IRQ1, IRQ0 enable 0 IRQ5, IRQ4, IRQ1 and IRQ0 interrupts are disabled 1 IRQ5, IRQ4, IRQ1 and IRQ0 interrupts are enabled
Rev.2.00 Mar. 22, 2007 Page 651 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
ISR--IRQ Status Register
Bit Initial value Read/Write 7 -- 0 R/W 6 -- 0 R/W 5 IRQ5F 0 R/W 4 IRQ4F 0 R/(W)*
H'F6
3 -- 0 -- 2 -- 0 --
Interrupt controller
1 IRQ1F 0 R/(W)* 0 IRQ0F 0 R/(W)*
IRQ5, IRQ4, IRQ1 and IRQ0 flags Bits 5, 4, 1 and 0 IRQ5F IRQ4F IRQ1F IRQ0F 0
Setting and Clearing Conditions [Clearing conditions] Read IRQnF when IRQnF = 1, then write 0 in IRQnF. IRQnSC = 0, IRQn input is high, and interrupt exception handling is carried out. IRQnSC = 1 and IRQn interrupt exception handling is carried out. [Setting conditions] IRQnSC = 0 and IRQn input is low. IRQnSC = 1 and IRQn input changes from high to low. (n = 5, 4, 1 and 0)
1
Note: * Only 0 can be written to clear the flag.
Rev.2.00 Mar. 22, 2007 Page 652 of 684 REJ09B0352-0200
Appendix B. Internal I/O Register Field
IPRA--Interrupt Priority Register A
Bit Initial value Read/Write 7 IPRA7 0 R/W 6 IPRA6 0 R/W 5 -- 0 R/W 4 IPRA4 0 R/W
H'F8
3 IPRA3 0 R/W 2
Interrupt controller
1 IPRA1 0 R/W 0 IPRA0 0 R/W
IPRA2 0 R/W
Priority level A7, A6, A4 to A0 0 Priority level 0 (low priority) 1 Priority level 1 (high priority)
* Interrupt sources controlled by each bit
Bit 7 IPRA7 Interrupt source IRQ0 Bit 6 IPRA6 IRQ1 Bit 5 -- -- Bit 4 IPRA4 IRQ4, IRQ5 Bit 3 IPRA3 WDT Bit 2 IPRA2 ITU channel 0 Bit 1 IPRA1 ITU channel 1 Bit 0 IPRA0 ITU channel 2
IPRB--Interrupt Priority Register B
Bit Initial value Read/Write 7 IPRB7 0 R/W 6 IPRB6 0 R/W 5 -- 0 R/W 4 -- 0 R/W
H'F9
3 IPRB3 0 R/W 2
Interrupt controller
1 IPRB1 0 R/W 0 -- 0 R/W
IPRB2 0 R/W
Priority level B7, B6, B3 to B1 0 Priority level 0 (low priority) 1 Priority level 1 (high priority)
* Interrupt sources controlled by each bit
Bit 7 IPRB7 Interrupt source ITU channel 3 Bit 6 IPRB6 ITU channel 4 Bit 5 -- -- Bit 4 -- -- Bit 3 IPRB3 SCI channel 0 Bit 2 IPRB2 SCI channel 1 Bit 1 IPRB1 A/D converter Bit 0 -- --
Rev.2.00 Mar. 22, 2007 Page 653 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
Appendix C I/O Block Diagrams
C.1 Port 1 Block Diagram
Software standby Modes 6 and 7
Internal data bus (upper)
Hardware standby Modes 1, 3, and 5 Reset S R Q D P1nDDR C WP1D Modes 6 and 7 Reset R P1n Q P1nDR C Modes 1, 3, and 5 WP1 D *
RP1
Legend WP1D: Write to P1DDR WP1: Write to port 1 RP1: Read port 1 Notes: n = 0 to 7 * Set priority
Figure C.1 Port 1 Block Diagram
Rev.2.00 Mar. 22, 2007 Page 654 of 684 REJ09B0352-0200
Internal address bus
Appendix C. I/O Block Diagrams
C.2
Port 2 Block Diagram
Reset Q Modes Software standby 6 and 7 Hardware standby RP2P Modes 1 and 3 S D P2nPCR C WP2P Reset R
Internal data bus (upper)
R
Q D P2nDDR C Modes 6 and 7 WP2D Reset R P2n Q P2nDR C Modes 1, 3, and 5 WP2 D *
RP2
Legend WP2P: RP2P: WP2D: WP2: RP2:
Write to P2PCR Read P2PCR Write to P2DDR Write to port 2 Read port 2
Notes: n = 0 to 7 * Set priority
Figure C.2 Port 2 Block Diagram
Rev.2.00 Mar. 22, 2007 Page 655 of 684 REJ09B0352-0200
Internal address bus
Appendix C. I/O Block Diagrams
C.3
Port 3 Block Diagram
Internal data bus (upper)
Reset Hardware standby Modes 6 and 7 Write to external address R Q D P3nDDR C WP3D Reset Modes 6 and 7 P3n Q R P3nDR C Modes 1, 3, and 5 WP3 D
RP3 Read external address
Legend WP3D: Write to P3DDR WP3: Write to port 3 RP3: Read port 3 Note: n = 0 to 7
Figure C.3 Port 3 Block Diagram
Rev.2.00 Mar. 22, 2007 Page 656 of 684 REJ09B0352-0200
Internal data bus (lower)
Appendix C. I/O Block Diagrams
C.4
Port 5 Block Diagram
Reset Q Software standby Hardware standby Modes 6 and 7 RP5P D P5nPCR C WP5P Modes 1 and 3 Reset S R Q D P5nDDR C Modes 6 and 7 WP5D Reset R P5n Q P5nDR C Modes 1, 3, and 5 WP5 D *
Internal data bus (upper)
R
RP5
Legend WP5P: RP5P: WP5D: WP5: RP5:
Write to P5PCR Read P5PCR Write to P5DDR Write to port 5 Read port 5
Notes: n = 0 to 3 * Set priority
Figure C.4 Port 5 Block Diagram
Rev.2.00 Mar. 22, 2007 Page 657 of 684 REJ09B0352-0200
Internal address bus
Appendix C. I/O Block Diagrams
C.5
Port 6 Block Diagrams
Internal data bus
Reset R Q D P60DDR Modes 6 and 7 C WP6D Reset R P60 Q P60DR C WP6 D
Bus controller WAIT input enable
RP6 Bus controller WAIT output Legend WP6D: Write to P6DDR WP6: Write to port 6 RP6: Read port 6
Figure C.5 (a) Port 6 Block Diagram (Pin P60)
Rev.2.00 Mar. 22, 2007 Page 658 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
Software standby Modes 6 and 7 Hardware standby Reset Q D P6nDDR C WP6D Reset Modes 6 and 7 P6n Q R P6nDR C WP6 AS output RD output WR output D
Internal data bus
R
Modes 1, 3, and 5
RP6
Legend WP6D: Write to P6DDR WP6: Write to port 6 RP6: Read port 6 Note: n = 3 to 5
Figure C.5 (b) Port 6 Block Diagram (Pins P63 to P65)
Rev.2.00 Mar. 22, 2007 Page 659 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
C.6
Port 7 Block Diagram
Internal data bus
A/D converter Input enable Analog input
RP7 P7n
Legend RP7: Read port 7 Note: n = 0 to 7
Figure C.6 Port 7 Block Diagram
Rev.2.00 Mar. 22, 2007 Page 660 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
C.7
Port 8 Block Diagrams
Reset Q D P80DDR C WP8D Reset R P80 Q P80DR C WP8 D
RP8
Internal data bus
Interrupt controller IRQ0 input
R
Legend WP8D: Write to P8DDR WP8: Write to port 8 RP8: Read port 8
Figure C.7(a) Port 8 Block Diagram (Pin P80)
Rev.2.00 Mar. 22, 2007 Page 661 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
Reset Q D P81DDR C WP8D Reset Modes 6 and 7 P81 Modes 1, 3, and 5 R Q P81DR C WP8 D
RP8
Internal data bus
Interrupt controller IRQ1 input
R
Legend WP8D: Write to P8DDR WP8: Write to port 8 RP8: Read port 8
Figure C.7 (b) Port 8 Block Diagram (Pin P81)
Rev.2.00 Mar. 22, 2007 Page 662 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
C.8
Port 9 Block Diagrams
Reset R Q D P90DDR C WP9D Reset R Q D SCI0 Output enable Serial transmit data Guard time
P90
P90DR C WP9
RP9
Legend WP9D: Write to P9DDR WP9: Write to port 9 RP9: Read port 9
Figure C.8 (a) Port 9 Block Diagram (Pin P90)
Rev.2.00 Mar. 22, 2007 Page 663 of 684 REJ09B0352-0200
Internal data bus
Appendix C. I/O Block Diagrams
Reset R Q D P91DDR C WP9D Reset R P91 Q P91DR C WP9 Output enable Serial transmit data D SCI1
RP9
Legend WP9D: Write to P9DDR WP9: Write to port 9 RP9: Read port 9
Figure C.8 (b) Port 9 Block Diagram (Pin P91)
Rev.2.00 Mar. 22, 2007 Page 664 of 684 REJ09B0352-0200
Internal data bus
Appendix C. I/O Block Diagrams
Reset R Q D P9nDDR C WP9D Reset R P9n Q P9nDR C WP9 D
Internal data bus
SCI Input enable
RP9
Serial receive data Legend WP9D: Write to P9DDR WP9: Write to port 9 RP9: Read port 9 Note: n = 2 or 3
Figure C.8 (c) Port 9 Block Diagram (Pins P92 and P93)
Rev.2.00 Mar. 22, 2007 Page 665 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
Reset R Q D P9nDDR C WP9D Reset R P9n Q P9nDR C WP9 Clock output enable Clock output D
Internal data bus
SCI Clock input enable
RP9
Clock input Interrupt controller IRQ4, IRQ5 input Legend WP9D: Write to P9DDR WP9: Write to port 9 RP9: Read port 9 Note: n = 4 or 5
Figure C.8 (d) Port 9 Block Diagram (Pins P94 and P95)
Rev.2.00 Mar. 22, 2007 Page 666 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
C.9
Port A Block Diagrams
Reset R Q D PAnDDR C WPAD Reset R
Internal data bus
WPA
TPC TPC output enable
PAn
Q
PAnDR C
D Next data
Output trigger
ITU RPA Counter input clock Legend WPAD: Write to PADDR WPA: Write to port A RPA: Read port A Note: n = 0 or 1
Figure C.9 (a) Port A Block Diagram (Pins PA0 and PA1)
Rev.2.00 Mar. 22, 2007 Page 667 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
Internal data bus
Reset R Q D PAnDDR C WPAD Reset R PAn Q PAnDR C WPA D
TPC TPC output enable
Next data
Output trigger ITU Output enable Compare match output
RPA
Input capture input Counter input clock
Legend WPAD: Write to PADDR WPA: Write to port A RPA: Read port A Note: n = 2 or 3
Figure C.9 (b) Port A Block Diagram (Pins PA2 and PA3)
Rev.2.00 Mar. 22, 2007 Page 668 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
Software standby Address output enable Mode 3 R Q D PAnDDR C WPAD Reset R PAn Q PAnDR C WPA Output trigger ITU Output enable Compare match output D Next data
Internal data bus
Reset
Internal address bus
TPC TPC output enable
RPA Input capture input Legend WPAD: Write to PADDR WPA: Write to port A RPA: Read port A Notes: 1. n = 4 to 7 2. PA7 address output enable is fixed at 1 in mode 3.
Figure C.9 (c) Port A Block Diagram (Pins PA4 to PA7)
Rev.2.00 Mar. 22, 2007 Page 669 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
C.10
Port B Block Diagrams
Reset R Q D PBnDDR C WPBD Reset R Q D Next data
Internal data bus
TPC TPC output enable
PBn
PBnDR C
WPB Output trigger ITU Output enable Compare match output
RPB Input capture input Legend WPBD: Write to PBDDR WPB: Write to port B RPB: Read port B Note: n = 0 to 3
Figure C.10 (a) Port B Block Diagram (Pins PB0 to PB3)
Rev.2.00 Mar. 22, 2007 Page 670 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
Internal data bus
Reset R Q D PBnDDR C WPBD Reset R PBn Q PBnDR C WPB D
TPC TPC output enable
Next data
Output trigger ITU Output enable Compare match output
RPB
Legend WPBD: Write to PBDDR WPB: Write to port B RPB: Read port B Note: n = 4 or 5
Figure C.10 (b) Port B Block Diagram (Pins PB4 and PB5)
Rev.2.00 Mar. 22, 2007 Page 671 of 684 REJ09B0352-0200
Appendix C. I/O Block Diagrams
Internal data bus
TPC TPC output enable Next data WPB Output trigger A/D converter ADTRG input Legend WPBD: Write to PBDDR WPB: Write to port B RPB: Read port B
Reset R Q D PB7DDR C WPBD Reset R PB7 Q PB7DR C D
RPB
Figure C.10 (c) Port B Block Diagram (Pin PB7)
Rev.2.00 Mar. 22, 2007 Page 672 of 684 REJ09B0352-0200
Appendix D. Pin States
Appendix D Pin States
D.1 Port States in Each Mode
Port States
Hardware Standby Mode T T T T Software Standby Mode H T T keep T 7 P27 to P20 1, 3 5, 6 T L T T T T keep T keep T 7 P37 to P30 P53 to P50 1, 3, 5, 6 7 1, 3 5, 6 T T T L T T T T T T keep T keep T keep T 7 P60 P65 to P63 P77 to P70 1, 3, 5, 6 7 1, 3, 5, 6 7 1, 3, 5 to 7 T T T H T T T T T T T T keep keep keep T keep T Program Execution State Sleep Mode Clock output RESO A7 to A0 [DDR = 0] Input port [DDR = 1] A7 to A0 I/O port A15 to A8 [DDR = 0] Input port [DDR = 1] A15 to A8 I/O port D15 to D8 I/O port A19 to A16 [DDR = 0] Input port [DDR = 1] A19 to A16 I/O port I/O port, WAIT I/O port WR, RD, AS I/O port Input port
Table D.1
Pin Name RESO*
1
Mode -- -- 1, 3 5, 6
Reset State Clock output T* L T
2
P17 to P10
Rev.2.00 Mar. 22, 2007 Page 673 of 684 REJ09B0352-0200
Appendix D. Pin States Hardware Standby Mode T T T Software Standby Mode keep keep [DDR = 0] T [DDR = 1] H 7 P95 to P90 PA 3 to PA0 PA6 to PA4 1, 3, 5 to 7 1, 3, 5 to 7 3, 6 T T T T T T T T keep keep keep [ADRCR = 0] T [ADRCR = 1] keep keep T keep keep Program Execution State Sleep Mode I/O port I/O port [DDR = 0] Input port [DDR = 1] H I/O port I/O port I/O port [ADRCR = 0] A21 to A23 [ADRCR = 1] I/O port I/O port A20 I/O port I/O port
Pin Name P80 P81
Mode 1, 3, 5, 6 7 1, 3, 5, 6
Reset State T T T
1, 5, 7 PA7 PB7, PB5 to PB0 3, 6 1, 5, 7 1, 3, 5 to 7
T L T T
T T T T
Legend H: High L: Low T: High-impedance state keep: Input pins are in the high-impedance state; output pins maintain their previous state. DDR: Data direction register ADRCR: Address control register Notes: 1. Mask ROM version. Dedicated FWE input pin for the F-ZTAT version. 2. Low output only when WDT overflows causes a reset.
Rev.2.00 Mar. 22, 2007 Page 674 of 684 REJ09B0352-0200
Appendix D. Pin States
D.2
Pin States at Reset
Reset in T1 State: Figure D.1 is a timing diagram for the case in which RES goes low during the T1 state of an external memory access cycle. As soon as RES goes low, all ports are initialized to the input state. AS, RD, and WR go high, and the data bus goes to the high-impedance state. The address bus is initialized to the low output level 0.5 state after the low level of RES is sampled. Sampling of RES takes place at the fall of the system clock ().
Access to external address T1 T2 T3
RES Internal reset signal Address bus (modes 1, 3, 5, 6) AS (modes 1, 3, 5, 6) RD (read access) (modes 1, 3, 5, 6) WR (write access) (modes 1, 3, 5, 6) Data bus (write access) (modes 1, 3, 5, 6) I/O port (modes 1, 3, 5 to 7) H'000000
High
High
High High impedance
High impedance
Figure D.1 Reset during Memory Access (Reset during T1 State)
Rev.2.00 Mar. 22, 2007 Page 675 of 684 REJ09B0352-0200
Appendix D. Pin States
Reset in T2 State: Figure D.2 is a timing diagram for the case in which RES goes low during the T2 state of an external memory access cycle. As soon as RES goes low, all ports are initialized to the input state. AS, RD, and WR go high, and the data bus goes to the high-impedance state. The address bus is initialized to the low output level 0.5 state after the low level of RES is sampled. The same timing applies when a reset occurs during a wait state (TW).
Access to external address T1 T2 T3
RES Internal reset signal Address bus (modes 1, 3, 5, 6) AS (modes 1, 3, 5, 6) RD (read access) (modes 1, 3, 5, 6) WR (write access) (modes 1, 3, 5, 6) Data bus (write access) (modes 1, 3, 5, 6) I/O port (modes 1, 3, 5 to 7) High impedance H'000000
High impedance
Figure D.2 Reset during Memory Access (Reset during T2 State)
Rev.2.00 Mar. 22, 2007 Page 676 of 684 REJ09B0352-0200
Appendix D. Pin States
Reset in T3 State: Figure D.3 is a timing diagram for the case in which RES goes low during the T3 state of an external memory access cycle. As soon as RES goes low, all ports are initialized to the input state. AS, RD, and WR go high, and the data bus goes to the high-impedance state. The address bus outputs are held during the T3 state.The same timing applies when a reset occurs in the T2 state of an access cycle to a two-state-access area.
Access to external address T1 T2 T3
RES Internal reset signal Address bus (modes 1, 3, 5, 6) AS (modes 1, 3, 5, 6) RD (read access) (modes 1, 3, 5, 6) WR (write access) (modes 1, 3, 5, 6) Data bus (write access) (modes 1, 3, 5, 6) I/O port (modes 1, 3, 5 to 7) High impedance H'000000
High impedance
Figure D.3 Reset during Memory Access (Reset during T3 State)
Rev.2.00 Mar. 22, 2007 Page 677 of 684 REJ09B0352-0200
Appendix E. Timing of Transition to and Recovery from Hardware Standby Mode
Appendix E Timing of Transition to and Recovery from Hardware Standby Mode
Timing of Transition to Hardware Standby Mode (1) To retain RAM contents with the RAME bit set to 1 in SYSCR, drive the RES signal low 10 system clock cycles before the STBY signal goes low, as shown below. RES must remain low until STBY goes low (minimum delay from STBY low to RES high: 0 ns).
STBY t1 10tcyc RES t2 0 ns
(2) When the RAME bit is cleared to 0 in SYSCR, or when RAM contents do not need to be retained, RES does not have to be driven low as in (1). Timing of Recovery from Hardware Standby Mode: Drive the RES signal low approximately 100 ns before STBY goes high.
STBY t 100 ns RES tOSC
Rev.2.00 Mar. 22, 2007 Page 678 of 684 REJ09B0352-0200
Appendix F. Product Lineup
Appendix F Product Lineup
Table F.1 H8/3022 Group Product Lineup
Part No. HD64F3022F HD64F3022TE Mask ROM version HD6433022F HD6433022TE H8/3021 Mask ROM version HD6433021F HD6433021TE H8/3020 Mask ROM version HD6433020F HD6433020TE Mark Code HD64F3022F HD64F3022TE HD6433022(***)F HD6433022(***)TE HD6433021(***)F HD6433021(***)TE HD6433020(***)F HD6433020(***)TE Package (Package Code) 80-pin QFP (FP-80A) 80-pin TQFP (TFP-80C) 80-pin QFP (FP-80A) 80-pin TQFP (TFP-80C) 80-pin QFP (FP-80A) 80-pin TQFP (TFP-80C) 80-pin QFP (FP-80A) 80-pin TQFP (TFP-80C)
Product Type H8/3022 F-ZTAT version
Note: (***) in mask ROM versions is the ROM code.
Rev.2.00 Mar. 22, 2007 Page 679 of 684 REJ09B0352-0200
Appendix G. Package Dimensions
Appendix G Package Dimensions
Figures G.1 and G.2 show the H8/3022 Group FP-80A and TFP-80C package dimensions.
JEITA Package Code P-QFP80-14x14-0.65 RENESAS Code PRQP0080JB-A Previous Code FP-80A/FP-80AV MASS[Typ.] 1.2g
HD
*1
D
60
41
61
40 bp b1
NOTE) 1. DIMENSIONS"*1"AND"*2" DO NOT INCLUDE MOLD FLASH 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET.
c1
*2
HE
E
c
Terminal cross section
ZE
80 21
Reference Dimension in Millimeters Symbol
1 ZD
20
F
A1
L L1
Detail F
e
*3
y
bp
x
M
D E A2 HD HE A A1 bp b1 c c1 e x y ZD ZE L L1
Nom Max 14 14 2.70 16.9 17.2 17.5 16.9 17.2 17.5 3.05 0.00 0.10 0.25 0.24 0.32 0.40 0.30 0.12 0.17 0.22 0.15 0 8 0.65 0.12 0.10 0.83 0.83 0.5 0.8 1.1 1.6
Min
A2
Figure G.1 Package Dimensions (FP-80A)
Rev.2.00 Mar. 22, 2007 Page 680 of 684 REJ09B0352-0200
A
c
Appendix G. Package Dimensions
JEITA Package Code P-TQFP80-12x12-0.50 RENESAS Code PTQP0080KC-A Previous Code TFP-80C/TFP-80CV MASS[Typ.] 0.4g
HD
*1
D 41
60
61
40 bp b1
NOTE) 1. DIMENSIONS"*1"AND"*2" DO NOT INCLUDE MOLD FLASH 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET.
c1
*2
HE
E
c
Terminal cross section
80 21
Reference Dimension in Millimeters Symbol
1 ZD Index mark
20
F
A1
L L1
*3
e
y
bp
Detail F
x M
D E A2 HD H1 A A1 bp b1 c c1 e x y ZD ZE L L1
Nom Max 12 12 1.00 13.8 14.0 14.2 13.8 14.0 14.2 1.20 0.00 0.10 0.20 0.17 0.22 0.27 0.20 0.12 0.17 0.22 0.15 8 0 0.5 0.10 0.10 1.25 1.25 0.4 0.5 0.6 1.0 Min
ZE
A2
Figure G.2 Package Dimensions (TFP-80C)
A
Rev.2.00 Mar. 22, 2007 Page 681 of 684 REJ09B0352-0200
c
Appendix H. Comparison of H8/300H Series Product Specifications
Appendix H Comparison of H8/300H Series Product Specifications
H.1 Differences between H8/3039F and H8/3022F
Differences between H8/3039F and H8/3022F
H8/3039F Operating range Operating power supply voltage Operating frequency On-chip RAM Flash memory Size Program/erase voltage Programming unit 4.5 V to 5.5 V 3.0 V to 5.5 V H8/3022F 3.0 V to 3.6 V
Table H.1
1 MHz to 18 MHz 4 kbytes 128 kbytes
1 MHz to 10 MHz
2 MHz to 18 MHz 8 kbytes 256 kbytes Supplied from VCC 128-byte simultaneous programming
Supplied from VCC 32-byte simultaneous programming
Write pulse application method Write pulse application method = 30 s x 6 + 200 s x 994 = 150 s x 4 + 500 s x 399 (with 10 s additional programming) Block configuration 8 blocks * * * EBR register configuration 1 kbyte x 4 28 kbytes x 1 32 kbytes x 3 12 blocks * * * 4 kbytes x 8 32 kbytes x 1 64 kbytes x 3
EBR I/O address: H'FF42
7 EB7 6 EB6 5 EB5 4 EB4 3 EB3 2 EB2 1 EB1 0 EB0
EBR1 I/O address: H'FF42
7 EB7 6 EB6 5 EB5 4 EB4 3 EB3 2 EB2 1 EB1 0 EB0
EBR2 I/O address: H'FF43
7 -- 6 -- 5 -- 4 -- 3 2 1 0 EB8 EB11 EB10 EB9
Flash error
FLMSR I/O address: H'FF4D
7 FLER 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 --
FLMCR2 I/O address: H'FF41
7 FLER 6 -- 5 -- 4 -- 3 -- 2 -- 1 -- 0 --
Rev.2.00 Mar. 22, 2007 Page 682 of 684 REJ09B0352-0200
Appendix H. Comparison of H8/300H Series Product Specifications
H8/3039F Flash memory RAM emulation register configuration RAM emulation RAM area Applicable blocks RAMCR I/O address: H'FF47
7 -- 6 -- 5 -- 4 -- 3 2 1 0 -- RAMS RAM2 RAM1
H8/3022F RAMER I/O address: H'FF47
7 -- 6 -- 5 -- 4 -- 3 2 1 0 RAMS RAM2 RAM1 RAM0
1 kbytes (H'FF800 to H'FFBFF) EB0 to EB3
4 kbytes (H'FE000 to H'FEFFF) EB0 to EB7 19,200 bps, 9,600 bps, 4,800bps Use of PROM programmer supporting Renesas Technology microcomputer device type with 256-kbyte on-chip flash memory (FZTAT256) Wait time setting of 0.1 ms or more -20C to +75C
Flash memory Boot mode bit 9,600 bps, 4,800 bps programming rate modes PROM mode Use of PROM programmer supporting Renesas Technology microcomputer device type with 128-kbyte on-chip flash memory (FZTAT128) Arbitrary setting Regular product: -20C to +75C Product with wide-range temperature specifications: -40C to +85C Standby current Ta 50C: 5 A Ta > 50C: 20 A
Oscillation stabilization wait time (with external clock) Electrical Operating characteristics temperature
Ta 50C: 10 A Ta > 50C: 80 A
Rev.2.00 Mar. 22, 2007 Page 683 of 684 REJ09B0352-0200
Appendix H. Comparison of H8/300H Series Product Specifications
Rev.2.00 Mar. 22, 2007 Page 684 of 684 REJ09B0352-0200
Renesas 16-Bit Single-chip Microcomputer Hardware Manual H8/3022 Group, H8/3022F-ZTATTM
Publication Date: 1st Edition, December, 1999 Rev.2.00, March 22, 2007 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp.
(c) 2007. Renesas Technology Corp., All rights reserved. Printed in Japan.
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
RENESAS SALES OFFICES
Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
http://www.renesas.com
Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510
Colophon 6.0
H8/3022 Group, H8/3022F-ZTAT Hardware Manual
TM
2-6-2, Ote-machi, Chiyoda-ku, Tokyo, 100-0004, Japan


▲Up To Search▲   

 
Price & Availability of H8-3022

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X