View SSL1005_4699766.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HIGH CURRENT POWER INDUCTORS
1. PART NO. EXPRESSION :
SSL1005 SERIES
SSL1005-R10MF
(a) (b) (c) (d)(e)
(a) Series code (b) Dimension code (c) Inductance code : R10 = 0.10uH
(d) Tolerance code : M = 20% (e) F : Lead Free
2. CONFIGURATION & DIMENSIONS :
A D
R10
B
E
L G
C
PCB Pattern Unit:m/m A 10.2 Max. B 6.8 Max. C 5.0 Max. D 1.50.5 E 2.50.5 G 5.5 Max. H 4.5 Max. L 10.5 Max.
3. SCHEMATIC :
4. GENERAL SPECIFICATION : a) Operating temp. : -55C to +125C b) Storage temp. : -55C to +125C c) Irms (A) : Will cause coil temp. to rise approximately T=40C without core loss. d) Isat (A) : Will cause L0 to drop approximately 20% e) Part temperature (ambient + temp. rise) : Should not exceed 125C under worst case operating conditions.
5. ELECTRICAL CHARACTERISTICS : Part No. SSL1005-R10MF SSL1005-R15MF SSL1005-R20MF Inductance L0 ( uH ) 0.10 20% 0.15 20% 0.20 20% Test Freq. ( Hz ) 0.25V/1M 0.25V/1M 0.25V/1M DCR (m ) Max. 0.65 0.65 0.65 Irms (A) Max. 40 40 30 Isat (A) Max. 50 42 40
NOTE : Specifications subject to change without notice. Please check our website for latest information.
H
05.05.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 1
HIGH CURRENT POWER INDUCTORS
6. CHARACTERISTICS CURVES :
SSL1005-R10MF
SSL1005 SERIES
SSL1005-R15MF
SSL1005-R20MF
NOTE : Specifications subject to change without notice. Please check our website for latest information.
05.05.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 2
HIGH CURRENT POWER INDUCTORS
7. RELIABILITY AND TEST CONDITION :
SSL1005 SERIES
ITEM
Electrical Characteristics Test Inductance DCR Heat Rated Current (Irms)
PERFORMANCE
Refer to standard electrical characteristics list
TEST CONDITION
HP4284A, CH11025, CH3302, CH1320, CH1320S LCR meter. CH16502, Agilent33420A Micro-Ohm Meter. Irms(A) will cause the coil temperature rise approximately T=40C without core loss 1. Applied the allowed DC current 2. Temperature measured by digital surface thermometer Isat(A) will cause Lo to drop approximately 20%
Saturation Current (Isat) Mechanical Performance Test Solderability Test More than 90% of the terminal electrode should be covered with solder.
Preheating Dipping 230C Natural cooling
Preheat : 150C, 60sec. Solder : Sn-Ag3.0-Cu0.5 Solder Temperature : 2305C Flux for lead free : rosin Dip Time : 41sec.
150C
60 seconds
41 seconds
Solder Heat Resistance
1. Appearance : No significant abnormality 2. Inductance change : Within 20%
Preheating 260C Dipping Natural cooling
Preheat : 150C, 60sec. Solder : Sn-Ag3.0-Cu0.5 Solder Temperature : 2605C Flux for lead free : rosin Dip Time : 100.5sec.
150C
60 seconds
100.5 seconds
Reliability Test High Temperature Life Test Low Temperature Life Test Thermal Shock Temperature : 1255C Time : 50012 hours Measure at room temperature after placing for 2 to 3 hrs. 1. Appearance : No damage 2. Inductance : Within 20% of initial value. No disconnection or short circuit. Temperature : -555C Time : 50012 hours Measure at room temperature after placing for 2 to 3 hrs. Conditions of 1 cycle.
Step 1 2 3 4 Temperature (C) -553 Room Temperature +1253 Room Temperature Times (min.) 303 Within 3 303 Within 3
Total : 5 cycles Measure at room temperature after placing for 2 to 3 hrs. Humidity Resistance 1. Appearance : No damage 2. Inductance : Within 20% of initial value. No disconnection or short circuit. Temperature : 405C Humidity : 90% to 95% Applied Current : Rated Curent Time : 50012 hours Measure at room temperature after placing for 2 to 3 hrs.
NOTE : Specifications subject to change without notice. Please check our website for latest information.
05.05.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 3
HIGH CURRENT POWER INDUCTORS
8. SOLDERIND AND MOUNTING : 8-1. Recommended PC Board Pattern ( Unit : mm )
10.5 5.5
SSL1005 SERIES
8-2. Soldering Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. 8-2.1 Solder Re-flow : Recommended temperature profiles for re-flow soldering in Figure 1. 8-2.2 Soldering Iron (Figure 2) : Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. Note : a) Preheat circuit and products to 150C. b) 280C tip temperature (max) c) Never contact the ceramic with the iron tip d) 1.0mm tip diameter (max) e) Use a 20 watt soldering iron with tip diameter of 1.0mm f) Limit soldering time to 3 secs.
Preheating TEMPERATURE C
250~260 230 180 150 60~120s
Soldering
4.5
TEMPERATURE C
10s max.
Natural cooling
Preheating
280 260 150
Soldering
Natural cooling
30~60s
Over 1min.
Gradual Cooling Within 3secs.
Figure 1. Re-flow Soldering
Figure 2. Iron Soldering
NOTE : Specifications subject to change without notice. Please check our website for latest information.
05.05.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 4
HIGH CURRENT POWER INDUCTORS
9. PACKAGING INFORMATION : 9-1. Reel Dimension
SSL1005 SERIES
COVER TAPE
2.00.5 D B OC A
EMBOSSED CARRIER
Type 13" x 24mm
A(mm) 24.00.5
B(mm) 752
C(mm) 13.50.5
D(mm) 330
9-2 Tape Dimension
1.750.1
4.00.1
2.00.1
O1.5+0.1
t
W
0.15 MIN
P Ao
Bo
Ko
Series SSL1005
Ao(mm) 7.20.1
Bo(mm) 10.60.1
Ko(mm) 5.40.1
P(mm) 12.00.1
W(mm) 24.00.3
t(mm) 0.350.05
9-3 Packaging Quantity
Size Chip / Reel Inner Box Carton
SSL1005 900 2700 5400
NOTE : Specifications subject to change without notice. Please check our website for latest information.
05.05.2008
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 5

▲Up To Search▲

Price & Availability of SSL1005

	To Download SSL1005 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .