 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| cPCI350 SERIES 350W 6Ux8HP DC/DC CompactPCITM Power Supply OBSOLETE PRODUCT Contact factory for replacement model SELECTION GUIDE Model Number CPCI350D-1 CPCI350D-1C Power 5V 350W 350W 50A1 50A 1 Output Current 3.3V 40A1 40A 1 Production Status -12V 2A 2A Consult Factory Active No Yes 12V 12A 12A INPUT CHARACTERISTICS Parameter Input Operating Voltage Input Voltage Withstand Conditions Min 36 34 72Vdc input 36 Typ Max 72 75 Units Vdc Vdc Apk FEATURES 6Ux8HP package 350W power at 0-50C PICMG 2.11 Compliant Widerange 36-72VDC Input Range PCI Voltage Architecture 47-pin I/O Connector No minimum load Hot-swap capable Inrush Current OUTPUT CHARACTERISTICS Output Nominal Voltage Output Current Min Max 50A1 40A1 12A 2A Typ 5 Total Regulation2 V1 V2 V3 V4 Parameter Output Voltage Adjustment Temperature Coefficient PARD (V1 & V2) +5.0Vdc +3.3Vdc +12Vdc -12Vdc Conditions V1 & V2 only 0A 0A 0A 0A Min 2% 2% +4/-2% +4/-2% Max Units %Vnom 0.02 %/C mVp-p mVp-p W W 8 200 %Vnom sec V V V V A mV 10 40 %Itot %Itot kVac kVac Vac 50 120 20MHz bandwidth 20MHz bandwidth 50C, 400lfm airflow 70C, 400lfm airflow V, 50% load step Settling time Output V1 (+5.0V) 5.5 3.8 13.0 -14.0 04 V1, V2, & V3 V1-V3; full load V4, full load Pri-Sec 4 1.5 500 500 6.0 4.3 13.5 -13.5 0 0 175 DESCRIPTION The cPCI350 is a high-reliability, 350W, 6Ux8HP CompactPCITM power supply operating from widerange 48Vdc-input. Equipped with the 47-pin I/O connector option, these units are fully compliant with the PICMG 2.11 R1.0 Power Interface Specification as well as the underlying CompactPCITM standards. ORing diodes and active current sharing allow the cPCI350 to be operated in N+n parallel-redundant configurations to support high-availability (HA) telecom applications. With a wide-range input of 36-72Vdc, safety agency approvals to UL1950 and EN60950, EMI compliance to ETSI and Telcordia standards, the cPCI350 was designed with globally-deployed systems in mind. Additional features include remote sense compensation, unit enable control (EN#), output inhibit control (INH#), output fault signal (FAL#), and thermal warning signal (DEG#). LEDs are provided for visual indication of input power presence and output fault condition. The proven design and complement of global safety agency approvals provide for an advanced power solution for your telecom CompactPCI requirements. PARD (V3 & V4) Output Power 350 Transient Response 6.5 4.8 14.0 -13.0 Over-Voltage Protection3 Output V2 (+3.3V) Output V3 (+12V) Output V4 (-12V) Minimum Load Remote Sense Compensation Current Share Tolerance Isolation Pri-Chassis Sec-Chassis Thermal Shutdown Notes: A thermal switch shuts down the power supply in the event that critical temperatures are exceeded. Unit will automatically restart when acceptable temperatures are restored. 1. Combined currents from outputs V1 & V2 not to exceed 50A total. 2. Total regulation includes line, load, and cross regulation. 3. Response to an OVP fault is a latching shutdown, restart of the unit requires cycling of the input power. 4. May not be in regulation. www.murata-ps.com cPCI350.A01 Page 1 of 6 cPCI350 SERIES 350W 6Ux8HP DC/DC CompactPCITM Power Supply GENERAL CHARACTERISTICS Parameter Efficiency MTBF Weight Conditions 48Vdc input, 350W load Calculated per MIL-HDBK-217F, 25C ambient, ground benign Calculated per MIL-HDBK-217F, 50C ambient, ground benign Unpackaged 374 174 0.7 Min Typ 68 Max Units % khrs khrs Kg PROTECTION Parameter Thermal Shutdown Input Protection Over-Voltage Protection Parameter Output Overload Protection Conditions/Response Automatic recovery upon restoration to operational temperatures Internal line fuse, Littlefuse 314020 or equivalent (fast-acting 3AB) All outputs Conditions/Response Outputs are individually protected against overloads and indefinite short circuit with automatic recovery upon removal of the fault condition. Overload response for all outputs is hiccup mode. Design Verification Testing (DVT) confirms that voltage excursions on the output buses resulting from insertion/extraction events do not exceed the specified maximum of 8%. However, routing of power and signal lines in the mating backplane is critical to minimization of such excursions. In addition, performance can be critically affected by load characteristics including resistance, negative resistance, and reactive components. While the control loop responses have been designed for optimum hot-swap performance over a wide range of characteristics, there may be instances where the voltage excursions exceed published specifications. In such cases, the control loop responses can be modified to perform optimally. Output isolation devices are present in all outputs to isolate faults within a failed power supply. 110 125 Inception Min Typ 90 20 145 Max Units C A %Vnom Hot-Swap Capability Output Fault Isolation STATUS & CONTROL SIGNALS & INDICATORS Name Enable (EN#) Output Inhibit (INH#) Output Fault (FAL#) Remote Sense (RS+, RS-) Thermal Warning (DEG#) Fault Indicator LED Power Present Indicator LED Description Short pin (#27) on connector will enable the outputs when the mating pin is grounded. Supply will not power up until this pin is engaged to its mate in the backplane. Unit output will be inhibited as pin is disengaged from the mating connector. Secondary referenced; active low, TTL compatible. Logic "0" or short circuit to output return inhibits all outputs. Secondary referenced. Open collector signal denotes that one of the output voltages has fallen below the lower regulation limit. Connection of the sense leads across the load at the desired point of regulation will compensate for voltage distribution drops up to 300mV between the output terminals of the power supply and the point of connection. The unit reverts to local sensing if the sense lines are opened for any reason. The output is protected against shorted or open leads. Applies to outputs V1-V3. Secondary referenced; TTL compatible. Open collector denotes a thermal warning; nominally, 10C prior to thermal shutdown. An LED will illuminate red if the output voltages are not within specification, coincident with assertion of the FAL# signal. A green LED will be illuminated when the input voltage is present and above the minimum requirement. www.murata-ps.com cPCI350.A01 Page 2 of 6 cPCI350 SERIES 350W 6Ux8HP DC/DC CompactPCITM Power Supply ENVIRONMENTAL CHARACTERISTICS Parameter Ambient OperatingTemperature Ambient Storage Temperature Over-Temperature Protection Humidity Conditions 400lfm of airflow is required to maintain full output power at 0 to 50C ambient. De-rate to 175W at 70C. At 200lfm and 50C ambient, output power is de-rated to 175W. Min 0 -20 Unit is protected against thermal overloead. Output will automatically restore upon recovery to acceptable temperatures. Operating; non-condensing Storage; non-condensing Operating. De-rate operating ambient temperature by 2C per 1000ft above 5000ft. Storage 10 5 -200 -200 90 90 10000 50000 % % ft ft Typ Max 70 85 Units C C Altitude ELECTROMAGNETIC COMPATIBILITY (EMC) Characteristic Conducted Emissions Compliance NEBS GR-1089 CERTIFICATIONS Agency/Characteristic UL CSA VDE CE RoHS SELV Vibration Shock Standard UL1950 CSA950 (per cUL) EN60950 LVD Directive; self-certified EN Directive 2002/95/EC; self-certified; see Selection Guide table for specific model compliance Self-certified MIL-STD-810d, Method 514.3, Procedure 1 MIL-STD-810d, Method 516.3, Procedure 1 SAFETY AGENCY RATINGS Input Voltage Input Current Input Power 48Vdc 15Adc 650W www.murata-ps.com cPCI350.A01 Page 3 of 6 cPCI350 SERIES 350W 6Ux8HP DC/DC CompactPCITM Power Supply PACKAGE SPECIFICATIONS All measurements are in inches. Weight: 0.7kg Shock: MIL-STD-810d, Method 516.3, Procedure 1. Vibration: MIL-STD-810d, Method 514.3, Procedure 1. Dimensions; 6U x 8 HP x 160mm. www.murata-ps.com cPCI350.A01 Page 4 of 6 cPCI350 SERIES 350W 6Ux8HP DC/DC CompactPCITM Power Supply PACKAGE SPECIFICATIONS (Continued) CONNECTORS Pin #1 1-4 5-12 13-18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Staging2 M M M M M M M M M M M S M M M M M M M M M M M M M M M M M L M M Signal Name V1 RTN V2 RTN V3 V4 RTN RESERVED3 RTN GA04 RESERVED EN# GA14 V1ADJ 4 Description V1 Output V1 and V2 Return V2 Output V3 Return V3 Output V4 Output Signal Return Reserved3 V4 Return Geographic Address Bit 0 Reserved Enable Geographic Address Bit 1 V1 Adjust V1 Remote Sense Geographic Address Bit 2 V2 Adjust V2 Remote Sense Sense Return V1 Current Share V3 Remote Sense Serial Communication Receive; Clock Degrade Signal Inhibit V1 SENSE GA2 4 V2ADJ4 V2 SENSE S RTN V1 SHARE V3 SENSE IPMB SCL DEG# INH# IPMB SDA V2 SHARE FAL# IPMB PWR4 V3 SHARE CGND ACN/+DC IN ACL/-DC IN 4 4 Serial Communication Transmit; Data V2 Current Share Fail Signal System Management Power V3 Current Share Chassis Ground (safety ground) AC Input Neutral / +DC Input AC Input Line / -DC Input Notes: 1. Pin numbers correspond to the female backplane connector. 2. L = Long Length Pin (First Make, Last Break); M = Medium Length Pins; S = Short Length Pins (Last Make, First Break). 3. PICMGTM 2.11 has reserved Pin 23 for future designation -- the cPCI350 uses this pin for synchronous start, required when N>1 for N+1 redundant configurations. 4. This function not available in the cPCI350DC. RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300C for 10 seconds. The pin termination finish on this product series is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The series is backward compatible with Sn/Pb soldering systems. For further information, please visit www.murata-ps.com/rohs ISO9001 CERTIFIED www.murata-ps.com cPCI350.A01 Page 5 of 6 cPCI350 SERIES 350W 6Ux8HP DC/DC CompactPCITM Power Supply USA: Canada: UK: France: Germany: Japan: China: Singapore: Mansfield (MA), Tel: (508) 339-3000, email: sales@murata-ps.com Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com Munchen, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com Parkway Centre, Tel: +65 6348 9096, email: singapore@murata-ps.com Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 www.murata-ps.com email: sales@murata-ps.com ISO 9001 REGISTERED 01/15/09 Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. (c) 2009 Murata Power Solutions, Inc. www.murata-ps.com cPCI350.A01 Page 6 of 6 |
Price & Availability of CPCI350D-1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |