View PLRXPL-VI-S24-22_4622153.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

COMMUNICATIONS MODUlES & SUBSySTEMS
RoHS-Compliant 2.125, 1.25 and 1.063 Gbps 850 nm eSFP Transceiver PLRXPL-VI-S24-22
Key Features
* Compliant with industry-wide physical and optical specifications * Lead-free and RoHS-Compliant * Cost effective SFP solution * Triple-rate FC/Ethernet performance * Enables higher port densities * Enables greater bandwidth * Proven high reliability
Applications
* High-speed storage area networks - Switch and hub interconnect - Mass storage systems interconnect - Host adapter interconnect * Computer cluster cross-connect * Custom high-speed data pipes * Short-reach Ethernet
This lead-free and RoHS-compliant multi-rate Small Form Factor Pluggable (SFP) transceiver provides superior performance for Fibre Channel and Ethernet applications, and is another in JDSU's family of products customized for high speed, short reach SAN, and intra-POP applications. The multi-rate feature enables its use in a wider range of system applications. It is fully compliant with FC-PI 100-M5/M6-SN-I, 200-M5/M6-SN-I, and 1000BASE-SX specifications. JDSU's housing provides improved EMI performance for demanding applications. This transceiver features a highly reliable 850 nm oxide vertical-cavity surface-emitting laser (VCSEL) coupled to a LC optical connector. Its small size allows for highdensity board designs that, in turn, enable greater total aggregate bandwidth.
Highlights
* 2GFC, 1GFC, and 1GBE triple rate performance enables flexible system design, and configuration * Lead-free and RoHS-compliant perEuropean Directive 2002/95/EC * Enhanced digital diagnostic feature set allows real-time monitoring of transceiver performance and system stability * Bail mechanism enables superior ergonomics and functionality in all port configurations * Extended voltage and extended temperature * MSA-compliant small form factor footprint * Serial ID allows customer and vendor system specific information to be placed in transceiver * All-metal housing provides superior EMI performance
NORTH AMERICA: 800 498-JDSU (5378)
wORlDwIDE: +800 5378-JDSU
wEBSITE: www.jdsu.com
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
2
PLRXPL-VI-S24-22 Features
* Utilizes a highly reliable, high-speed, 850nm, oxide VCSEL * Lead-free and RoHS-compliant * Hot pluggable * Digital diagnostics, SFF-8472 rev 9.5 compliant * Compliant with Fibre Channel 200M5/M6-SN-I and 100-M5/M6-SN-I * Compliant with 1000BASE-SX, IEEE 802.3 * Low nominal power consumption (400 mW) * -20C to 85C operating temperature range for 2Gbps datarates * -40C to 85C operating temperature range for 1Gbps datarates * Single +3.3 V power supply * 10% extended operating voltage range * Bit error rate < 1 x 10-12 * OCTransmit disable, loss of signal and transmitter fault functions * CDRH and IEC 60825-1 Class 1 laser eye safe * FCC Class B compliant * ESD Class 2 per MIL-STD 883
2.224 56.50
.470 11.94
.539 13.70
Dimensions in inches [mm]
An eye-safe, cost effective serial transceiver, the PLRXPL-VI-S24-22 features a small, low power, pluggable package that manufacturers can upgrade in the field, adding bandwidth incrementally. The robust mechanical design features a unique all-metal housing that provides superior EMI shielding.
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
Section 1 Functional Description
PLRXPL-VI-S24-22 850 nm VCSEL Gigabit Transceiver is designed to transmit and receive 8B/10B encoded serial optical data over 50/125 m or 62.5/125 m multimode optical fiber.
Transmitter
The transmitter converts 8B/10B encoded serial PECL or CML electrical data into serial optical data meeting the requirements of 100-M5/M6-SN-I, 200-M5/M6SN-I Fibre Channel specifications and 1000BASE-SX Ethernet. Transmit data lines (TD+ & TD-) are internally AC coupled with 100 W differential termination. An open collector compatible Transmit Disable (Tx_Dis) is provided. This pin is internally terminated with a 10 kW resistor to VccT. A logic "1," or no connection on this pin will disable the laser from transmitting. A logic "0" on this pin provides normal operation. The transmitter has an internal PIN monitor diode that is used to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (TFault) is provided. The Transmit Fault signal must be pulled high on the host board for proper operation. A logic "1" output from this pin indicates that a transmitter fault has occurred, or the part is not fully seated and the transmitter is disabled. A logic "0" on this pin indicates normal operation.
Receiver
The receiver converts 8B/10B encoded serial optical data into serial PECL/CML electrical data. Receive data lines (RD+ & RD-) are internally AC coupled with 100 W differential source impedance, and must be terminated with a 100 W differential load. The receiver's bandwidth has been optimized for fully compliant operation at 2.125, 1.25 and 1.063 Gbps line rates without the use of rate select. Rate select pin 7 has no effect. An open collector compatible Loss of Signal is provided. The LOS must be pulled high on the host board for proper operation. A logic "0" indicates that light has been detected at the input to the receiver (see Section 2.5 Optical characteristic, Loss of Signal Assert/Deassert Time on page 9). A logic "1" output indicates that insufficient light has been detected for proper operation. Power supply filtering is recommended for both the transmitter and receiver. Filtering should be placed on the host assembly as close to the Vcc pins as possible for optimal performance. Recommended "Application Schematics" are shown in Figure 2 on page 5.
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
4
10 k
16 Transmitter Power Supply 3 Transmitter Disable In
VCC_TX TX_DIS
TD+
18 Transmitter Positive Data
TOSA
Laser Driver
TX_GND TX_FAULT TD -
100
19 Transmitter Negative Data 2 Transmitter Fault Out 1, 17, 20 Transmitter Signal Ground
SCL
Management Processor EEPROM
SDA
5 MOD_DEF(1) Serial ID Clock 4 MOD_DEF(2) Serial ID Data 6 MOD_DEF(0) 15 Receiver Power Supply
VCC_RX
VCC_RX
RD RD +
50
12 Receiver Negative Data Out 13 Receiver Positive Data Out
ROSA
RX_GND
Receiver
RX_GND LOS
50
8 Loss of Signal Out
7 Rate Select 30 k 9, 10, 11, 14 Receiver Signal Ground
Figure 1
Block diagram
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
Section 2 Application Schematics
Recommended connections to the PLRXPL-VI-S24-22 transceiver are shown in figure 2 below.
Vcc Z* = 100 1 VeeT VeeT 20 R2* 50 Open Collector Driver (Tx Disable) Vcc 2 Tx Fault TD- 19 R1* 50
10 k? Receiver (Tx Fault)
PECL Driver (TX DATA)
Open Collector Bidirectional (Mod_Def(2))
10 k
3 Tx Disable
TD+ 18
Open Collector Bidirectional (Mod_Def(1))
Receiver (Mod_Def(0))
Rate Select 9 VeeR Vcc 10 VeeR VeeR 11 RD- 12
Receiver (LOS)
Notes Power supply filtering components should be placed as close to the Vcc pins of the host connector as possible for optimal performance. PECL driver and receiver will require biasing networks. Please consult application notes from suppliers of these components. CML I/O on the PHY are supported. MOD_DEF(2) and MOD_DEF(1) should be bi-directional open collector connections in order to implement serial ID (MOD_DEF[0,1,2]) PLRXPL-VI-S24-22 transceiver. R1 and R2 may be included in the output of the PHY. Check application notes of the IC in use. * Transmission lines should be 100 differential traces. It is recommended that the termination resistor for the PECL Receiver (R3 + R4) be placed beyond the input pins of the PECL Receiver. Series Source Termination Resistors on the PECL Driver (R1+R2) should be placed as close to the driver output pins as possible

Vcc
4 MOD_DEF(2)
VeeT 17 C3 0.1F
L1 1 H L2 1 H
Vcc +3.3V Input C2 0.1 F C1 10F
10 k Vcc
5 MOD_DEF(1)
VccT 16

6 MOD_DEF(0)
VccR 15 C4 0.1 F C5 10 F
10 k

7 Rate Select
VeeR 14
R3* 50 8 LOS RD+ 13 Z* = 100
PECL Receiver (RX DATA)
R4* 50
10 k
Figure 2
Recommended application schematic for the PLRXPL-VI-S24-22 transceiver
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
2.1
Technical data
Technical data related to the RoHS-Compliant 2.125, 1.25 and 1.063 Gbps 850 nm eSFP Transceiver includes: * Section 2.2 Pin function definitions below * Section 2.3 Absolute maximum ratings on page 8 * Section 2.4 Electrical characteristics on page 8 * Section 2.5 Optical characteristic on page 10 * Section 2.6 Link lengths on page 11 * Section 2.7 Regulatory compliance on page 12 * Section 2.8 PCB layout on page 13 * Section 2.9 Front panel opening on page 14 * Section 2.10 Module outline on page 14 * Section 2.11 Transceiver belly-to-belly mounting on page 15
2.2
Pin function definitions
Figure 3
Transceiver pin descriptions
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
Table 1 Transceiver pin descriptions
Pin Number Receiver 8
Symbol
Name
Description
LOS
Loss of Signal Out (OC)
9, 10, 11, 14 12
VeeR RD-
Receiver Signal Ground Receiver Negative DATA Out (PECL) Receiver Positive DATA Out (PECL) Receiver Power Supply
13
RD+
15
VccR
7 Transmitter 3
Rate Select
Rate Select (LVTTL)
Sufficient optical signal for potential BER < 1x10-12 = Logic "0" Insufficient optical signal for potential BER < 1x10-12 = Logic "1" This pin is open collector compatible, and should be pulled up to Host Vcc with a 10 kW resistor. These pins should be connected to signal ground on the host board. Light on = Logic "0" Output Receiver DATA output is internally AC coupled and series terminated with a 50 W resistor. Light on = Logic "1" Output Receiver DATA output is internally AC coupled and series terminated with a 50 W resistor. This pin should be connected to a filtered +3.3V power supply on the host board. See Application schematics on page 5 for filtering suggestions. This pin has an internal 30K pulldown to ground. An input signal will not affect module performance Logic "1" Input (or no connection) = Laser off Logic "0" Input = Laser on This pin is internally pulled up to VccT with a 10 kW resistor. These pins should be connected to signal ground on the host board. Logic "1" Output = Laser Fault (Laser off before t_fault) Logic "0" Output = Normal Operation This pin is open collector compatible, and should be pulled up to Host Vcc with a 10 kW resistor. This pin should be connected to a filtered +3.3V power supply on the host board. See Application schematics on page 5 for filtering suggestions. Logic "1" Input = Light on Transmitter DATA inputs are internally AC coupled and terminated with a differential 100 W resistor. Logic "0" Input = Light on Transmitter DATA inputs are internally AC coupled and terminated with a differential 100 W resistor. Serial ID with SFF 8472 Diagnostics (See section 3.1) Module Definition pins should be pulled up to Host Vcc with 10 kW resistors.
TX Disable
Transmitter Disable In (LVTTL)
1, 17, 20 2
VeeT TX Fault
Transmitter Signal Ground Transmitter Fault Out (OC)
16
VccT
Transmitter Power Supply
18
TD+
Transmitter Positive DATA In (PECL) Transmitter Negative DATA In (PECL)
19
TD-
Module Definition 4, 5, 6 MOD_DEF(0:2)
Module Definition Identifiers
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
2.3 Absolute maximum ratings
Parameter Storage temperature Operating case temperature Power supply voltage Transmitter differential input voltage Relative humidity
Symbol Tst Tc Vcc VD RH
Ratings -40 to +95 -40 to +85 0 to +4.0 2.5 5 to 95
Unit C C V VP-P %
2.4
Electrical characteristics
Parameter Supply voltage Data rate Operating temperature range Transmitter Supply current Data input voltage swing Data input rise/fall time Data input rise/fall time Data input skew Data input deterministic jitter Data input deterministic jitter Data input deterministic jitter Data input total jitter Data input total jitter Data input total jitter Transmit disable voltage level
Symbol Vcc Tc Tc ICCT VTDp-p
Min 2.97 1.0 -40 -20
Typical 3.3 2.125
Max 3.63 2.2 85 85 70 2200 175 350 20 0.12 0.14 0.1 0.25 0.26 0.24
Unit V Gbps C C mA mVp-p ps ps ps UI UI UI UI UI UI V V s ms V V s s ms
Notes
BER < 1x10-12 for 1G datatrates for 2G datarates
250 60 60
40 800
Differential, peak to peak 20% - 80%, differential 2 GBd operation 3 20% - 80%, differential 1 GBd operation 3 K28.5 pattern, T, @ 1.062 Gbps 1, 5 K28.5 pattern, T, @ 2.125 Gbps 1, 5 K28.5 pattern, TP1, @ 1.25 Gbps 1, 5 27-1 pattern, T, BER < 1x10-12, @ 1.062 Gbps 1, 5 27-1 pattern, T, BER < 1x10-12, @ 2.125Gbps 1, 5 27-1 pattern, TP1, BER < 1x10-12, @ 1.25 Gbps 1, 5 Laser output disabled after TTD if input level is VIH; laser output enabled after TTEN if input level is VIL Laser output disabled after TTD if input level is VIH; laser output enabled after TTEN if input level is VIL Transmit fault level is VOH and laser output disabled TFault after laser fault. Transmitter fault is VOL and laser output restored TINI after transmitter disable is asserted for TReset, then disabled. After hot plug or Vcc 2.97V
DJ DJ DJ TJ TJ TJ VIH VIL TTD TTEN VOH VOL TFault TReset TINI Vcc -0.5 0 10 Vcc -1.0 0
Vcc 0.8 10 1 Vcc 0.5 100
Transmit disable/enable assert time
Transmit fault output voltage level Transmit fault assert and reset times Initialization time
300
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
2.4 Electrical characteristics
(continued)
Parameter Receiver Supply current Data output voltage swing Data output rise/fall time Data output skew Data output deterministic jitter Data output deterministic jitter Data output deterministic jitter Total jitter Total jitter Total jitter Loss of signal voltage level
Symbol
Min
Typical
Max
Unit
Notes
ICCR 600
85 90
120 200 50 0.36 0.39 0.46 0.61 0.64 0.75
DJ DJ DJ TJ TJ TJ VOH VOL Vcc -0.5 0
mA mVp-p ps ps UI UI UI UI UI UI V V s s
Vcc 0.5 100 100
Loss of signal assert/deassert time
TLOSA TLOSD
RLOAD = 100 W, differential 20% - 80%, differential RLOAD = 100 W, differential K28.5 pattern, R, @ 1.062 Gbps 1, 9 K28.5 pattern, R, @ 2.125 Gbps 1, 5 K28.5 pattern, TP4, @ 1.25 Gbps 1, 5 27-1 pattern, R , BER < 1x10-12 @ 1.062 Gbps 1, 5 27-1 pattern, R , BER < 1x10-12 @ 2.125 Gbps 1, 5 27-1 pattern, TP4, BER < 1x10-12 @ 1.25 Gbps 1, 5 LOS output level VOL TLOSD after light input > LOSD 2 LOS output level VOH TLOSA after light input < LOSA 2 LOS output level VOL TLOSD after light input > LOSD 2 LOS output level VOH TLOSA after light input < LOSA 2
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
10
2.5 Optical characteristics
Parameter Transmitter Wavelength RMS spectral width Average optical power Optical output rise/fall time Optical modulation amplitude Extinction ratio Deterministic jitter Deterministic jitter Deterministic jitter Total jitter Total jitter Total jitter Relative intensity noise (OMA) Receiver Wavelength Maximum input power Sensitivity (OMA)
Symbol lp Dl PAVG trise/fall OMA ER DJ DJ DJ TJ TJ TJ RIN12 OMA l Pm S1 S2 ISI = 0.96 dB ISI = 2.18 dB ISI = 2.2 dB ISI = 2.6 dB ISI = 1.26 dB ISI = 2.03 dB LOSD LOSA FC
Min
Typical
Max
Unit
Notes
830 -9.5 200 9
850 0.5
500
860 0.85 -2.5 150 1125 0.21 0.26 0.20 0.43 0.44 0.43 -117 860 31 49
-125 770 0 850 12 16 55 67 69 87 96 109 -21 -30 0.2
nm nm dBm ps W dB UI UI UI UI UI UI dB/Hz nm dBm Wp-p Wp-p Wp-p Wp-p Wp-p Wp-p Wp-p Wp-p dBm dBm MHz
20% - 80% K28.5 pattern, T, @ 1.062 Gbps 1, 5 K28.5 pattern, T, @ 2.125 Gbps 1, 5 K28.5 pattern, TP2, @ 1.25 Gbps 1, 5 27-1 pattern, T, @ 1.062 Gbps 1, 5 27-1 pattern, T, @ 2.125 Gbps 1, 5 27-1 pattern, TP2, @ 1.25 Gbps 1, 5 2GHz, 12 dB reflection
Stressed sensitivity (OMA) SS1.06 Stressed sensitivity (OMA) SS1.25 Stressed sensitivity (OMA) SS2.12 Loss of signal assert/deassert level Low frequency cutoff
-17 0.3
1 Gbps operation, maximum is equivalent to -17dBm @9dB ER 2 Gbps operation 1.0625G operation 1.0625G operation 1.25G operation 1.25G operation 2.125G operation 2.125G operation Chatter free operation -3 dB, P<-16 dBm
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
11
2.6 link length
Data Rate / Standard 1.0625 GBd Fibre Channel 100-M5-SN-I 100-M6-SN-I 1.25 Gbps IEEE 802.3 1000Base-SX
Fiber Type 62.5/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 62.5/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 62.5/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF 50/125 m MMF
Modal Bandwidth @ 850 nm (MHz*km) 200 500 900 1500 2000 200 500 900 1500 2000 200 500 900 1500 2000
Distance Range (m) .5 to 300 .5 to 500 .5 to 630 .5 to 755 .5 to 860 .5 to 275 .5 to 550 .5 to 595 .5 to 740 .5 to 860 .5to 150 .5 to 300 .5 to 350 .5 to 430 .5 to 500
Notes 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
2.125 GBd Fibre Channel 200-M5-SN-I, 200-M6-SN-I
Specification notes 1. UI (Unit Interval): one UI is equal to one bit time. For example, 2.125 Gbits/s corresponds to a UI of 470.588ps. 2. For LOSA and LOSD definitions see Loss of Signal Assert/Deassert Level in Section 2.5 Optical characteristic on page 10. 3. When operating the transceiver at 1.0 - 1.3 Gbaud only, a slower input rise and fall time is acceptable. If it is planned to operate the module in the 1.0 - 2.12 Gbaud range, faster input rise and fall times are required. 4. Measured with stressed eye pattern as per FC-PI (Fibre Channel) and 1000BASE-SX using the worst case specifications. 5. All jitter measurements performed with worst case input jitter according to FC-PI and 1000BASE-SX. 6. Distances, shown in the "Link Length" table, are the distances specified in the Fibre Channel and Ethernet standards. "Link Length" distances are calculated for worst case fiber and transceiver characteristics based on the optical and electrical specifications shown in this document using techniques utilized in IEEE 802.3 (Gigabit Ethernet). In the nominal case, longer distances are achievable.
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
12
2.7 Regulatory compliance
The PLRXPL-VI-S24-22 complies with international Electromagnetic Compatibility (EMC) and international safety requirements and standards (see details in Table 2 below). EMC performance is dependent on the overall system design. Information included herein is intended as a figure of merit for designers to use as a basis for design decisions. The PLRXPL-VI-S24-22 is lead-free and RoHS-compliant per Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
Table 2 Regulatory compliance
Feature Component safety
Test Method UL 60950 UL94-V0 IEC 60950 Directive 2002/95/EC
Performance UL File E209897 TUV Report/Certificate (CB scheme) Compliant per the Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment CDRH compliant and Class 1 laser safety.
Lead-free and RoHS-compliant
Laser eye safety Electromagnetic Compatibility (EMC) CE Electromagnetic emmissions
U.S. 21CFR (J) 1040.10 EN 60825 EU Declaration of Conformity EMC Directive 89/336/EEC FCC CFR47 Part 15 IEC/CISPR 22 AS/NZS CISPR22 EN 55022 ICES-003, Issue 4 VCCI-03 EMC Directive 89/336/EEC IEC /CISPR/24 EN 55024 EN 61000-4-2 EN 61000-4-3
Compliant with European EMC and Safety Standards Noise frequency range: 30 MHz to 12 GHz. Good system EMC design practice required to achieve Class B margins.
Electromagnetic immunity
ESD immunity Radiated immunity
Exceeds requirements. Withstand discharges of: 8 kV contact, 15kV and 25kV Air Exceeds requirements. Field strength of 10 V/m RMS, from 10 MHz to 1 GHz. No effect on transceiver performance is detectable between these limits.
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
1
2.8 PCB layout
34.50 2X 30 A
CROSS-HATCHED AREA DENOTES COMPONENT AND TRACE KEEPOUT (EXCEPT CHASSIS GROUND)
NOTES: 1. DATUM AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER.
20 3X 10 2X 7.20 2X 2.50 2X 2.50 3X 7.10 0.850.05 2 (MARKED "S") 0.1 A B C D
A A
2. PADS AND VIAS ARE CHASSIS GROUND 11 PLACES 3. THRU HOLES, PLATING OPTIONAL 4. HOLES DENOTED WITH 'A' ARE NOT REQUIRED WITH PICOLIGHT CAGES (6 PLACES) 5. ALL DIMENSIONS ARE IN MILLIMETERS
1
B
11.9 1
3.68
1.70
8.48
16.25
14.25 TYP
11.08
8.58
5.68
A A A A
B
9.60 4.80 1.70
11.93
2 TYP
2
2 10X
0.1
1.050.05 L AC
26.80
5 10 3 PLACES 41.30 42.30
9X 0.950.05 3 (MARKED "G") 0.1 L A C
THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED)
Figure 4
Board layout
10X 5 10X 3.20
G G S G
2X 0.90
G
10.93 9.60 9X 0.8
G
10.53 9X 0.8
11.93
G
G
G
G
20X 0.500.03 0.06 C D
2X 1.550.05 0.1 L C D
20.05 TYP 0.06 L C D
ALL DIMENSIONS ARE IN MILLIMETERS
Figure 5
Detail layout
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
14
2.9 Front panel opening
Figure 6
Figure 7
2.10
Module outline
All dimensions in inches [mm] Figure 7
December, 2006 05001369 Rev 3
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
1
2.11 Transceiver belly-to-belly mounting
6X .600.004 4X .640.004
6X .41.00
.135
.074
.042 .138
All dimensions in inches
Section
Related Information
Other information related to the RoHS-Compliant 2.125, 1.25 and 1.063 Gbps 850 nm eSFP Transceiver includes: * Section 3.1 Digital Diagnostic Monitoring and Serial ID Operation below * Section 3.2 Package and handling instructions on page 21 * Section 3.3 ESD Discharge (ESD) on page 21 * Section 3.4 Eye safety on page 21
3.1
Digital Diagnostic Monitoring and Serial ID Operation
The PLRXPL-VI-S24-22 is equipped with a 2-wire serial EEPROM that is used to store specific information about the type/identification of the transceiver as well as real-time digitized information relating to the transceiver's performance. See Section IV, "Module Definition Interface and Data Field Description" of the SFP-MSA Pin Definitions and Host Board Layout document for memory/address organization of the identification data and the Small Form Factor Commitee's document number SFF-8472 Rev 9.5, dated June 1, 2004 for memory/address organization of the digital diagnostic data. The enhanced digital diagnostics feature monitors five key transceiver parameters which are Internally Calibrated and should be read as absolute values and interpreted as follows;
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
1
Transceiver Temperature in degrees Celsius: Internally measured. Represented as a 16 bit signed two's complement value in increments of 1/256 degrees Celsius from -40 to +125 degree C with LSB equal to 1/256 degrees C. Accuracy is 3 degrees Celsius over the specified operating temperature and voltage range. Vcc/Supply Voltage in Volts: Internally measured. Represented as a 16 bit unsigned integer with the voltage defined as the full 16 bit value(0-65535) with LSB equal to 100mV with a measurement range of 0 to +6.55V. Accuracy is 3% of nominal value over the specified operating temperature and voltage ranges. TX Bias Current in mA: Represented as a 16 bit unsigned integer with current defined as the full 16 bit value(0-65535) with LSB equal to 2mA with a measurement range of 0 - 131mA. Accuracy is 10% of nominal value over the specified operating temperature and voltage ranges. TX Output Power in mW: Represented as a 16 bit unsigned integer with the power defined as the full 16 bit value (0-65535) with LSB equal to 0.1mW. Accuracy is 2dB over the specified temperature and voltage ranges over the range of 100mW to 800mW (-10dBm to -1dBm). Data is not valid when transmitter is disabled. RX Received Optical Power in mW: Represented as average power as a 16 bit unsigned integer with the power defined as the full 16 bit value(0-65535) with LSB equal to 0.1mW. Accuracy over the specified temperature and voltage ranges is 3dB from 30mW to 1000mW (-15dBm to 0dBm).
Reading the data
The information is accessed through the MOD_DEF(1), and MOD_DEF(2) connector pins of the module. The specification for this EEPROM (ATMEL AT24CO1A family) contains all the timing and addressing information required for accessing the data. The device address used to read the Serial ID data is 1010000X(A0h), and the address to read the diagnostic data is 1010001X(A2h). Any other device addresses will be ignored. Refer to Table 3, Table 4, and Table 5 for information regarding addresses and data field descriptions MOD_DEF(0), pin 6 on the transceiver, is connected to Logic 0 (Ground) on the transceiver. MOD_DEF(1), pin 5 on the transceiver, is connected to the SCL pin of the EEPROM. MOD_DEF(2), pin 4 on the transceiver, is connected to the SDA pin of the EEPROM. The EEPROM WP pin is internally tied to ground with no external access, allowing write access to the customer-writable field(bytes 128-247 of address 1010001X). Note: address bytes 0-127 are not write protected and may cause diagnostic malfunctions if written over.
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
1
Decoding the data
The information stored in the EEPROM including organization is defined in the Small Form-Factor Pluggable Multisource (SFP-MSA) Pin Definitions and Host Board Layout document, dated 3/13/00, Section IV. The digital diagnostic information stored in the EEPROM is defined in the Small Form-Factor document SFF-8472 draft rev 9.5, dated June 1, 2004.
Table 3 Data Field Descriptions
0
Address(1010000X)(A0h)
Serial ID Information; Defined by SFP MSA
0 55 95
Address(1010001X)(A2h)
Alarm and Warning Limits Reserved for External Calibration Constants Real Time Diagnostic Information JDSU Specific Information Non-volatile, customerwriteable, field-writeable area
95
JDSU Specific Information
119 127
127
Reserved for SFP MSA
247 255 255
JDSU Specific Information
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
1
Table 4 Serial ID Data and Map
Memory Address Address (1010000X)(A0h) 0 1 2 3-10 11 12 13 14 15 16 17 18 19 20-35 36 37-39 40-55 56-59 60-61 62 63 64 65 66 67 68-83 84-91 92 93 94 95
value
Comments
03 04 07 0000000120400C05 01 15 00 00 00 1E 0F 00 00 JDSU 00 000485
0352
00 1A 04 34
68 F0 2
SFP Transceiver SFP with Serial ID LC Connector 850nm, multi-mode, 1.062/2.125 FC, Intermediate Distance and 1000Base-SX 8B10B encoding mechanism Nominal Bit rate of 2.125Gbps Reserved Single mode fiber not supported Single mode fiber not supported 300 meters of 50/125 mm fiber 150 meters of 62.5/125 mm fiber Copper not supported Reserved Vendor Name (ASCII) Reserved IEEE Company ID (ASCII) Part Number (ASCII, no hyphens included) Rev of part number (ASCII) Wavelength of laser in nm; 850 Reserved Check Code; Lower 8 bits of sum from byte 0 through 62 Reserved No Rate Select, Tx_Disable, Tx Fault, Loss of Signal implemented Bit rate max of 2.2Gbps Bit rate min of 1.0Gbps Serial Number (ASCII) Date Code (ASCII) Diagnostics monitoring type Digital diagnostics Compliance SFF-8472 Rev 9.4 Check Code; Lower 8 bits of sum from byte 64 through 94
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
1
Table 5 Diagnostics Data Map
Memory Address Address (1010001X)(A2h) 00-01 02-03 04-05 06-07 08-09 10-11 12-13 14-15 16-17 18-19 20-21 22-23 24-25 26-27 28-29 30-31 32-33 34-35 36-37 38-39 40-55 56-59 60-63 64-67 68-71 72-75 76-77 78-79 80-81 82-83 84-85 86-87 88-89 90-91 92-94 95 96 97 98 99 100
value
Comments
Temp High Alarm Temp Low Alarm Temp High Warning Temp Low Warning Voltage High Alarm Voltage Low Alarm Voltage High Warning Voltage Low Warning Bias High Alarm Bias Low Alarm Bias High Warning Bias Low Warning TX Power High Alarm TX Power Low Alarm TX Power High Warning Tx Power Low Warning RX Power High Alarm RX Power Low Alarm RX Power High Warning RX Power Low Warning Reserved RP4 RP3 RP2 RP1 RP0 Islope Ioffset TPslope TPoffset Tslope Toffset Vslope External Calibration Constant Reserved Checksum Temperature MSB Temperature LSB Vcc MSB Vcc LSB TX Bias MSB
MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address MSB at low address For future monitoring quantities External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant External Calibration Constant Refer to SFF-8472 rev 9.5 Reserved Low order 8 bits of sum from 0-94 Internal temperature AD values Internally measured supply voltage AD values TX Bias Current AD values
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
20
Table 5 Diagnostics Data Map (continued)
Memory Address Address (1010001X)(A2h) 101 102 103 104 105 106 107 108 109 110-7 110-6 110-5 110-4 110-3 110-2 110-1 110-0 111 112-119 120-127 128-247 248-255
value
Comments
TX Bias LSB TX Power MSB TX Power LSB RX Power MSB RX Power LSB Reserved MSB Reserved LSB Reserved MSB Reserved LSB Tx Disable State Soft Tx Disable Control Reserved Rate Select State Soft Rate Select Control Tx Fault State LOS State Data Ready State Reserved Optional alarm & warning flag bits Vendor specific User/Customer EEPROM Vendor specific
Measured TX output power AD values Measured RX input power AD values For 1st future definition of digitized analog input For 2nd future definition of digitized analog input Digital State of Tx Disable Pin Writing "1" disables laser, this is OR'd with Tx_Disable pin
Digital State Digital State Digital State; "1" until transceiver is ready Reserved Refer to SFF-8472 rev 9.5 Vendor specific Field writeable EEPROM Vendor specific
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
21
3.2 Package and handling instructions
Process plug
The PLRXPL-VI-S24-22 is supplied with a dust cover. This plug protects the transceiver's optics during standard manufacturing processes by preventing contamination from air borne particles. Note: It is recommended that the dust cover remain in the transceiver whenever an optical fiber connector is not inserted.
Recommended cleaning and de-greasing chemicals
JDSU recommends the use of methyl, isopropyl and isobutyl alcohols for cleaning. Do not use halogenated hydrocarbons (e.g. trichloroethane, ketones such as acetone, chloroform, ethyl acetate, MEK, methylene chloride, methylene dichloride, phenol, N-methylpyrolldone).
Flammability
The PLRXPL-VI-S24-22 housing is made of cast zinc and sheet metal.
3.3 ESD Discharge (ESD)
Handling
Normal ESD precautions are required during the handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed from the packaging and handled only in an ESD protected environment utilizing standard grounded benches, floor mats, and wrist straps.
Test and operation
In most applications, the optical connector will protrude through the system chassis and be subjected to the same ESD environment as the system. Once properly installed in the system, this transceiver should meet and exceed common ESD testing practices and fulfill system ESD requirements. Typical of optical transceivers, this module's receiver contains a highly sensitive optical detector and amplifier which may become temporarily saturated during an ESD strike. This could result in a short burst of bit errors. Such an event might require that the application re-acquire synchronization at the higher layers (e.g. Serializer/Deserializer chip).
3.4 Eye safety
The PLRXPL-VI-S24-22 is an international Class 1 laser product per IEC 825, and per CDRH, 21 CFR 1040 Laser Safety Requirements. The PLRXPL-VI-S24-22 is an eye safe device when operated within the limits of this specification. Operating this product in a manner inconsistent with intended usage and specification may result in hazardous radiation exposure.
ROHS-COMPlIANT 2.125, 1.25 AND 1.063 GBPS 850 NM TRANSCEIvER
Caution
Tampering with this laser based product or operating this product outside the limits of this specification may be considered an act of "manufacturing," and will require, under law, recertification of the modified product with the U.S. Food and Drug Administration (21 CFR 1040). The use of optical instruments with this product will increase eye hazard. At the normal operating current, optical output power with an unaided eye can be as much as 30 mW at a wavelength of 850 nm. Approximately ten times this power level could be collected with an eye loupe.
Order Information
For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide or via e-mail at customer.service@jdsu.com.
Sample: PLRXPL-VI-S24-22
Part Number PLRXPL-VI-S24-22 Temp. Range -40 to C 1G -20 to C 2G Power Supply Tolerance 10% Dual Rate Fiber Channel X 1000Base-SX X Digital Diagnostics X PCI Compliant X
NORTH AMERICA: 800 498-JDSU (5378)
wORlDwIDE: +800 5378-JDSU
wEBSITE: www.jdsu.com
Product specifications and descriptions in this document subject to change without notice. (c) 2008 JDS Uniphase Corporation 30149155 500 0608 PLRXPL-VI-S24-22.DS.CMS.AE
June 2008

▲Up To Search▲

Price & Availability of PLRXPL-VI-S24-22

	To Download PLRXPL-VI-S24-22 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .