View ELN-60-12_4575691.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

60W Single Output Class 2 Switching Power Supply
Features :
Universal AC input / Full range
ELN-60
series
Built-in constant current limiting circuit with adjustable OCP level Protections: Short circuit / Overload / Over voltage Fully isolated plastic case with IP64 level IP64 design for indoor or outdoor installations Optional dimming function : 1~10VDC(D type) or PWM controlled(P type) UL1310 Class 2 power unit Cooling by free air convection 100% full load burn-in test Low cost, high reliability Suitable for LED lighting and moving sign applications 2 years warranty
ELN-60-9 DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER 9V 5A 0 ~ 5A 45W 8.7 ~ 10.5V LED OPERATION VOLTAGE Note.8 3 ~ 9V ELN-60-12 12V 3 ~ 12V 5A 0 ~ 5A 60W 120mVp-p 10.8 ~ 13.2V ELN-60-15 15V 3 ~ 15V 4A 0 ~ 4A 60W 150mVp-p 13.5 ~ 16.5V ELN-60-24 24V 3 ~ 24V 2.5A 0 ~ 2.5A 60W 150mVp-p 21.6 ~ 26.4V ELN-60-27 27V 3 ~ 27V 2.3A 0 ~ 2.3A 62.1W 200mVp-p 24.3 ~ 29.7V
SPECIFICATION
MODEL
IP64
ELN-60-48 48V 3 ~ 48V 1.3A 0 ~ 1.3A 62.5W 250mVp-p 43.2 ~ 52.8V
RIPPLE & NOISE (max.) Note.2 120mVp-p OUTPUT VOLTAGE ADJ. RANGE Note.7
Can be adjusted by internal potential meter SVR1 5.0% 1.0% 2.0%
CURRENT ADJ. RANGE Note.7 -25% ~ 3%. Can be adjusted by internal potential meter SVR2 VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT(max.) LEAKAGE CURRENT OVER CURRENT PROTECTION OVER VOLTAGE
Note.6 500ms, 30ms / 230VAC
1500ms, 30ms / 115VAC at full load
50ms/230VAC
Note.5 90 ~ 264VAC
16ms/115VAC at full load
47 ~ 63Hz 82% 85% 86% 87% 87% 88% 1.2A/115VAC 0.7A/230VAC COLD STAR 60A/230VAC 0.25mA / 240VAC 95 ~ 110% 130% max. 54 ~ 60V Protection type : Constant current limiting, recovers automatically after fault condition is removed 11 ~ 13.5V 13.8 ~ 16V 17.5 ~ 21V 28 ~ 32V 31 ~ 35V
Protection type : Shut down o/p voltage, re-power on to recover FUNCTION DIMMING CONTROL (OPTIONAL) 1 ~ 10VDC or PWM signal : 100Hz ~ 3KHz WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE -20 ~ +60 -40 ~ +80 0.03%/ (Refer to output load derating curve) , 10 ~ 95% RH (0 ~ 50 ) 20 ~ 90% RH non-condensing
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes Design refer to UL1310 Class 2,TUV EN60950-1, CAN/CSA C22.2 No. 223-M91(except for 48V), EN61347-2-13; IP64 approved I/P-O/P:3KVAC
SAFETY & ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH EMC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B HARMONIC CURRENT EMS IMMUNITY MTBF OTHERS DIMENSION PACKING
NOTE
Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A 603Khrs min. MIL-HDBK-217F (25 ) 181*61.5*35mm (L*W*H) 0.4Kg; 24pcs/11Kg/0.75CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the derating curve for more details. 5. The power supply is considered a component which will be installed a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. 7. Output voltage can be adjusted through the SVR1 on the PCB ; limit of output constant current level can be adjusted through the SVR2 on the PCB. 8. Constant current operation region is within the specified output voltage range above. This is the suitable operation region for LED related applications.
File Name:ELN-60-SPEC 2008-06-16
60W Single Output Class 2 Switching Power Supply
Mechanical Specification
181 6.26
ELN-60
Case No.960A
series
Unit:mm
21.25
2-R2.5
300
61.5
300 AC/L(Brown) AC/N(Blue) 18AWG 2C
+V(Red) -V(Black) 18AWG 2C
6.26
21.25
OUTPUT(with optional dimming function)
Output voltage and current adjustment : remove the upper case and adjust through SVR1 & SVR2 shown in the diagram.
+V(Red) -V(Black) DIM+(Blue) DIM-(White)
SVR1 SVR2
SVR1 Output voltage adjustment SVR2 Output current adjustment
Block Diagram
I/P EMI FILTER & RECTIFIERS POWER SWITCHING RECTIFIERS & FILTER DETECTION CIRCUIT PWM CONTROL O.V.P. O.C.P.
fosc : 60KHz
+V -V DIM10V PWM or 1~10V DIM+ Optional Dimming Control
O.L.P.
Derating Curve
Static Characteristics
Ta=25
100 100 90 80 80 70
60
LOAD (%)
40
LOAD (%)
50
60 50 40
20
-20
-15
-5
0
15
30
40 45 50
60 (HORIZONTAL)
90
100
125
135
145
155 165
175
180
200
230
264
AMBIENT TEMPERATURE ( )
INPUT VOLTAGE (V) 60Hz
File Name:ELN-60-SPEC 2008-06-16
35
60W Single Output Class 2 Switching Power Supply
Dimming Control (Optional)
Level of output current can be adjusted through the dimming control function. (1)1~10V
ELN-60
series
95%
DIM+
Vdc
Output Current
+
DIMVdc:1~10V
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 0
45%
5% 1 2 3 4 5 6 7 8 9 10
DC Input
(2)PWM
V f: 100Hz ~ 3KHz
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 0% 10% 11% 20% 30% 40% 50% 60% 70% 80% 90% 100% 95%
Output Current
f 10V
60%
t1
t2
f
15%
Duty= t1 ,0 ~ 100% t1+t2 Lo:0V Hi:10V
Duty Cycle
File Name:ELN-60-SPEC 2008-06-16
60W Single Output Class 2 Switching Power Supply
Recommend Application Deployment (24V)
ELN-60
series
+V(Red)
24V, 2.5A ELN-60-24
-V(Black)
+V(Red)
24V, 2.5A ELN-60-24
-V(Black)
R
R
R
R LED
1 to 6 LEDs // 4 strips This configuration is based on LED with the following parameters : VF= 3.0~3.5V I F = 600~700mA
LED
6 LEDs // 1 to 4 strips This configuration is based on LED with the following parameters : VF= 3.0~3.5V R=10 ohm, 10W IF=600~700mA
+V(Red)
24V, 2.5A
ELN-60-24
-V(Black)
+V(Red)
24V, 2.5A
ELN-60-24
-V(Black)
R
R
R
R
R
R
R
R
LED
1 to 6 LEDs // 8 strips This configuration is based on LED with the following parameters : VF= 3.0~3.5V I F =3 00~350mA
LED
6 LEDs // 1 to 8 strips This configuration is based on LED with the following parameters : VF= 3.0~3.5V R=20 ohm, 3W IF=300~350mA
File Name:ELN-60-SPEC 2008-06-16

▲Up To Search▲

Price & Availability of ELN-60-12

	To Download ELN-60-12 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .