 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| M306H7MG-XXXFP/MC-XXXFP/FGFP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER REJ03B0152-0210 Rev.2.10 Oct 25, 2006 1. DESCRIPTION The M306H7MG/MC-XXXFP and M306H7FGFP are single-chip microcomputers using the highperformance silicon gate CMOS process using M16C/62 Series CPU core and is packaged in a 100-pin plastic molded QFP. This single-chip microcomputer operates using sophisticated instructions featuring a high level of instruction efficiency. With 1M bytes of address space, this is capable of executing instructions at high speed. This also features a built-in data slicer, making this correspondence to Global broadcasting service. 1.1 Features Mask version : 256 K/128 K bytes Flash memory version : 256 K bytes RAM Mask version : 8 K/5 K bytes Flash memory version : 8 K bytes * Shortest instruction execution time ..62.5 ns (f(XIN)=16 MHz) * Supply voltage ..................................VCC1=3.00 V to VCC2, VCC2=4.5 V to 5.5 V(at f(XIN)=16 MHz) VCC1=2.00 V to VCC2, VCC2=2.00 V to 5.5 V(at f(XCIN)=32 kHz) *VCC2=2.0 V to 2.9 V: Operates only in the low power dissipation mode * Interrupts ..........................................25 internal and 8 external interrupt sources, 4 software interrupt sources; 7 levels * Multifunction 16-bit timer ..................5 output timers + 6 input timers * Serial I/O ..........................................6 channels UART/clock synchronous: 3 Clock synchronous: 2 Multi-master I2C: 1 * DMAC...............................................2 channels (trigger: 24 sources) * A/D converter ...................................8 bits X 8 channels (Expandable up to 10 channels) * CRC calculation circuit ....................1 circuit * Watchdog timer ................................1 line * Programmable I/O ............................79 lines (P6 to P7, P80 to P84: Can be used as 3.3 V interface) * Input port ..........................................1 port (P85 shared with NMI pin) * Clock generating circuit ....................2 built-in circuits (built-in feedback resistor, external crystal oscillator is required) * Data slicer ........................................For PDC, VPS, WSS, EPG-J, CC, CC2X, ID-1 * Memory capacity ..............................ROM 1.2 Applications DVD recorder, HDD recorder Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 1 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP ------Table of Contents-----1. DESCRIPTION.............................................................1 1.1 Features ..........................................................1 1.2 Applications.....................................................1 Table of Contents ......................................................2 1.3 Pin Configuration.............................................3 1.4 Performance Outline .......................................4 1.5 Block Diagram.................................................6 1.6 Memory .........................................................10 2. CENTRAL PROCESSING UNIT (CPU)..................... 11 2.1 Data Registers (R0, R1, R2 and R3)............. 11 2.2 Address Registers (A0 and A1)..................... 11 2.3 Frame Base Register (FB) ............................12 2.4 Interrupt Table Register (INTB) .....................12 2.5 Program Counter (PC) ..................................12 2.6 User Stack Pointer (USP) and Interrupt Stack Pointer (ISP) ..12 2.7 Static Base Register (SB)..............................12 2.8 Flag Register (FLG) ......................................12 3. RESET ......................................................................13 3.1 Hardware Reset ............................................13 3.2 Software Reset..............................................14 3.3 Watchdog Timer Reset..................................14 3.4 SFR ...............................................................17 4. CLOCK GENERATION CIRCUIT ..............................25 4.1 Oscillator Circuit ............................................30 4.2 CPU Clock and Peripheral Function Clock ...33 4.3 Clock Output Function...................................33 4.4 Power Control ...............................................35 4.5 System Clock Protective Function ................41 5. PROTECTION............................................................42 6. INTERRUPTS ............................................................43 6.1 Type of Interrupts ..........................................43 6.2 Software Interrupts ........................................44 6.3 Hardware Interrupts ......................................45 6.4 Interrupts and Interrupt Vector ......................46 6.5 Interrupt Control ............................................48 6.6 I Flag .............................................................50 6.7 IR Bit .............................................................50 6.8 ILVL2 to ILVL0 Bits and IPL...........................50 6.9 Interrupt Sequence........................................51 6.10 Interrupt Response Time...............................52 6.11 Variation of IPL when Interrupt Request is Accepted ...... 52 6.12 Saving Registers ...........................................53 6.13 Returning from an Interrupt Routine..............55 6.14 Interrupt Priority.............................................55 6.15 Interrupt Priority Resolution Circuit ...............55 6.16 INT Interrupt ..................................................57 6.17 NMI Interrupt .................................................58 6.18 Address Match Interrupt................................58 7. WATCHDOG TIMER ..................................................60 8. DMAC ......................................................................62 8.1 Transfer Cycles .............................................67 8.2 Number of DMA Transfer Cycles ..................69 8.3 DMA Enable ..................................................70 8.4 DMA Request................................................70 8.5 Channel Priority and DMA Transfer Timing...71 9. TIMERS......................................................................72 9.1 Timer A..........................................................73 9.2 Timer B..........................................................87 10. SERIAL I/O ..............................................................93 10.1 UARTi (i=0 to 2).............................................93 10.2 Clock Synchronous serial I/O Mode............102 10.3 Clock Asynchronous Serial I/O (UART) Mode .... 109 10.4 Special Mode 1 (I2C mode)......................... 116 10.5 Special Mode 2............................................126 10.6 Special Mode 3 (IE mode)...........................131 10.7 Special Mode 4 (SIM Mode) (UART2).........133 10.8 SI/O3 and SI/O4..........................................138 11. MULTI-MASTER I2C BUS INTERFACE................143 12. A/D CONVERTER .................................................163 12.1 One-shot Mode ...........................................167 12.2 Repeat mode...............................................169 12.3 Single Sweep Mode ....................................171 12.4 Repeat Sweep Mode 0................................173 12.5 Repeat Sweep Mode 1................................175 12.6 Sample and Hold.........................................177 1. DESCRIPTION 12.7 Extended Analog Input Pins ....................... 177 12.8 External Operation Amp Connection Mode .... 177 12.9 Current Consumption Reducing Function....... 178 12.10 Analog Input Pin and External Sensor Equivalent Circuit Example .... 178 12.11 Caution of Using A/D Converter...................... 179 13. CRC CALCULATION ............................................ 180 14. EXPANSION FUNCTION ...................................... 182 14.1 Expansion function description................... 182 14.2 Expansion memory..................................... 183 14.3 slice RAM ................................................... 184 14.4 CRC Operation Circuit (EPG-J).................. 187 14.5 Expansion Register .................................... 200 14.6 Expansion Register Construction Composition... 240 14.7 8/4 Humming Decoder ............................... 247 14.8 24/18 Humming Decoder ........................... 248 14.9 I/O Composition of pins for Expansion Function. 250 15. PROGRAMMABLE I/O PORTS............................ 252 15.1 Port Pi Direction Register (PDi Register, i = 0 to 9) ..252 15.2 Port Pi Register (Pi Register, i = 0 to 9)...... 252 15.3 Pull-up Control Register 0 to Pull-up Control Register 2 (PUR0 to PUR2 Registers) ....... 252 15.4 Port Control Register.................................. 252 16. ELECTRICAL CHARACTERISTICS .................... 263 17. FLASH MEMORY VERSION ................................ 279 17.1 Flash Memory Performance ....................... 279 17.2 Memory Map .............................................. 281 17.3 Boot Mode .................................................. 282 17.4 Functions To Prevent Flash Memory from Rewriting...282 17.5 CPU Rewrite Mode..................................... 284 17.6 Data Protect Function................................. 298 17.7 Status Register ........................................... 298 17.8 Full Status Check ....................................... 300 17.9 Standard Serial I/O Mode ........................... 302 17.10 Parallel I/O Mode........................................ 307 18. PACKAGE OUTLINE ............................................ 308 19. USEGE NOTES .................................................... 309 19.1 Precautions for Power Control ................... 309 19.2 Precautions for Protect............................... 309 19.3 Precautions for Interrupts ........................... 309 19.4 Precautions for DMAC................................ 313 19.5 Precautions for Timers ............................... 314 19.6 Precautions for Serial I/O (Clock-synchronous Serial I/O)... 317 19.7 Precautions for Serial I/O (UART Mode) .... 318 19.8 Precautions for A/D Converter ................... 318 19.9 Precautions for Programmable I/O Ports.... 318 19.10 Electric Characteristic Differences Between Mask ROM and Flash Memory Version Microcomputers ........................ 318 19.11 Precautions for Flash Memory Version ...... 318 19.12 Other Notes ................................................ 323 19.13 Serial I/O (RxDi input setup time) ............... 325 19.14 Precautions for LP3 and LP4 pins .............. 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 2 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 1. DESCRIPTION 1.3 Pin Configuration Figures 1.1 shows the pin configuration (top view). Pin configuration (top view) P1_5/INT3 P1_6/INT4 P1_7/INT5 P3_0 P1_0 P1_1 P1_2 P1_3 P1_4 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7 P3_1 P3_2 P3_3 P3_4 P3_5 P3_6 P3_7 P4_0 P4_1 P4_2 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 P0_7/AN7 P0_6/AN6 P0_5/AN5 P0_4/AN4 P0_3/AN3 P0_2/AN2 P0_1/AN1 P0_0/AN0 CVIN VDD2 VCCOFF VSS2 TEST1 LP3 LP4 AVSS M1 SYNCIN AVCC P97/ADTRG/SIN4 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 50 49 48 47 46 45 44 43 42 P4_4 P4_5 P4_6 P4_7 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7/CLKOUT P6_0/CTS0/RTS0 P6_1/CLK0 P6_2/RXD0/SCL0 P6_3/TXD0/SDA0 P6_4/CTS1/RTS1 P6_5/CLK1 P6_6/RXD1/SCL1 P6_7/TXD1/SDA1 P4_3 41 40 39 38 37 36 35 34 33 32 31 M306H7FGFP/M306H7MG/MC-XXXFP VCC2 VSS P7_3/CTS2/RTS2/TA1IN P9_5/ANEX0/CLK4 P8_3/INT1 P8_2/INT0 RESET XOUT P9_4/TB4IN/RMTIN P8_1/TA4IN P9_6/ANEX1/SOUT4 P7_2/CLK2/TA1OUT P9_2/TB2IN/SOUT3 P8_6/XCOUT VSS P8_0/TA4OUT P7_5/TA3OUT XIN P7_1/RXD2/SCL2/TA0IN/TB5IN(Notes 1) Notes 1: N channel open-drain output pins. Notes 2: When using Multi-master I2C, N channel open-drain output pins. P7_0/TXD2/SDA2/TA0OUT(Notes 1) P9_0/TB0IN/CLK3 P8_7/XCIN STARTB VCC1 P9_3/TB3IN/JSTIN P9_1/TB1IN/SIN3 P7_7/TA3IN CNVSS P7_4/SDA3/TA2OUT(Notes 2) P8_4/RMTOUT/INT2 P7_5/SCL3/TA2IN(Notes 2) P8_5/NMI 100P6S-A Figure 1.1 Pin configuration (top view) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 3 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 1. DESCRIPTION 1.4 Performance Outline Performance outline is shown in Table 1.1. Performance outline Performance 91 instructions 62.5 ns (f(XIN)= 16MHZ, VCC= 4.5V to 5.5V) Refer to the Product table (Table 1.2) Refer to the Product table (Table 1.2) 8-bit x 7, 2-bit x 1 : VCC2 system 8-bit x 2, 5-bit x 1 : VCC1 system 1-bit x 1 (NMI pin VCC2 level judgment) : VCC2 system 16-bit x 5 channels 16-bit x 6 channels 3 channels Clock synchronous serial I/O, Clock asynchronous serial I/O, I2C bus1., or IEBus2. 2 channels Clock synchronous serial I/O Table 1.1 Item Number of basic instructions Shortest instruction execution time Memory capacity I/O port Input port Multi function timer ROM RAM P0 to P5, P86 to P87, P9 P6 to P7, P80 to P84 P85 TA0, TA1, TA2, TA3, TA4 TB0, TB1, TB2, TB3, TB4, TB5 Serial I/O Serial I/O A/D converter DMAC Multi-master I2C I2C bus x 1 8 bits x (8 + 2) channels 2 channels (trigger: 24 sources) CRC-CCITT 15 bits x 1 (with prescaler) 25 internal and 8 external sources, 4 software sources, 7 levels 2 circuits * Main clock * Sub-clock (These circuits contain a built-in feedback resistor and external crystal oscillator) CRC calculation circuit Watchdog timer Interrupt Clock generation circuit VCC1=3.00 V to VCC2, VCC2= 4.5 V to 5.5 V (at f(XIN)=16MHZ) Power supply voltage VCC1=3.00 V to VCC2, VCC2= 4.00 V to 5.5 V (at f(XIN)=16MHZ)3. VCC1=2.90 V to VCC2, VCC2= 2.90 V to 5.5 V (at f(XIN)=16MHZ, at divide-by-8 or 16)3. VCC1=2.0 V to VCC2, VCC2=2.0 V to 5.5 V (at f(XCIN)=32kHZ, only low-power consumption mode) 3.4. Flash memory Program/erase voltage Number of program/erase 5.0 V 0.25 V 100 times CMOS high performance silicon gate 100-pin plastic mold QFP Slice RAM Data slicer Data slicer 864 bytes (48 x 18 x 8-bit) Corresponds to PDC, VPS, WSS, EPG-J, CC, CC2X and ID-1 Device configuration Package Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 4 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 1. DESCRIPTION NOTES: 1. I2C bus is a registered trademark of Koninklijke Philips Electronics N.V. If you desire this option, please so specify. 2. IEBus is a registered trademark of NEC Electronics Corporation. 3. If the VCC2 supply voltage is less than 4.50 V, the A/D converter, data slicer cannot be used. 4. If the VCC2 supply voltage is less than 2.60 V, be aware that only the CPU, RAM, clock timer, interrupt, and I/O ports can be used. Other control circuits (e.g., timers A and B, serial I/O, UART) cannot be used. Table 1.2 Product table Remarks Mask ROM version 100P6S-A Mask ROM version Flash Memory version Type No. M306H7MG-XXXFP M306H7MC-XXXFP M306H7FGFP ROM capacity 256K bytes 128K bytes 256K bytes RAM capacity 8K bytes 5K bytes 8K bytes Package type Type No. M 3 0 6 H 7 M G - XXX FP Package type: FP : Package 100P6S-A ROM No. Omitted for flash memory version ROM capacity: G : 256K bytes C : 128K bytes Memory type: M : Mask ROM version F : Flash memory version Shows RAM capacity, pin count, etc (The value itself has no specific meaning) M16C/6H Group M16C Family Figure 1.2 Type No, Memory Size, and Package Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 5 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 1. DESCRIPTION 1.5 Block Diagram Figure 1.3 is a block diagram. 8 8 8 8 8 8 8 Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6 Port P7 Internal peripheral functions Timer (16-bit) Output (timer A): 5 Input (timer B): 6 A-D converter (8 bits X 8 channels Expandable up to 10 channels) UART or clock synchronous serial I/O (8 bits X 3 channels) CRC arithmetic circuit (CCITT) (Polynomial :X16+X12+X5+1) System clock generator XIN-XOUT XCIN-XCOUT Clock synchronous serial I/O (8 bits X 2 channels) Slicer 8 Port P80-P84 5 Multi-master I C 2 Port P85 M16C/60 series16-bit CPU core Watchdog timer (15 bits) DMAC (2 channels) R0H R1H R2 R3 A0 A1 FB R0L R1L SB USP ISP INTB PC FLG Memory ROM Port P86, P87 RAM 2 Multiplier Port P9 8 Figure 1.3 Block diagram Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 6 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 1.3 Pin Description (1) 1. DESCRIPTION Pin name VCC1, VCC2, VSS CNVSS RESET XIN XOUT Signal name Power supply input CNVSS Reset input Clock input Clock output I/O type Power supply Function Apply 2.00 V to 5.5 V to the Vcc1 and Vcc2 pins. Apply 0 V to the Vss pin. Input condition of Vcc1 and Vcc2 are Vcc1 Vcc2. (1.) Input Input Input Output VCC2 VCC2 VCC2 Connect this pin to VSS. "L" on this input resets the microcomputer. These are I/O pins provided for main clock oscillation circuit. Connect ceramic resonator or crystal oscillator between pins XIN and XOUT. To use an externally derived clock, input it to XIN pin and leave XOUT pin open. AVCC AVSS P00 to P07 Analog power supply input Analog power supply input I/O port P0 Input/output VCC2 This pin is a power supply input for the A/D converter. Connect this pin to VCC. This pin is a power supply input for the A/D converter. Connect this pin to VSS. This is an 8-bit CMOS I/O port. This port has an I/O select direction register, allowing each pin in that port to be directed for input or output individually. If any port is set for input, selection can be made for it in a program whether or not to have a pull-up resistor in 4 bit units. Pins in this oprt also function as A/D converter input pins as selected by Program. P10 to P17 P20 to P27 I/O port P1 I/O port P2 Input/output VCC2 Input/output VCC2 This is an 8-bit I/O port equivalent to P0. Pins P15 to P17 in this port also functionas INT interrupt input pins as selected by software. This is an 8-bit I/O port equivalent to P0. Note 1: In this datasheet, hereafter, VCC refers to VCC2 unless otherwise noted. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 7 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 1.4 Pin name P30 to P37 P40 to P47 P50 to P57 1. DESCRIPTION Pin Description (2) Signal name I/O port P3 I/O port P4 I/O port P5 I/O type Input/output output Input/output Power supply VCC2 VCC2 VCC2 Function This is an 8-bit I/O port equivalent to P0. This is an 8-bit I/O port equivalent to P0. This is an 8-bit I/O port equivalent to P0. The same frequency as divide-by-8, 32 of XIN from P57 or XCIN are output by program selecting. This is an 8-bit I/O port equivalent to P0. These pins function as I/O pin of UART0 and UART1 by selecting it by the program. This is an 8-bit I/O port equivalent to P0 (P70 and P71 are N channel open-drain output). This port can function as I/O pins for timers A0 to A3 when so selected in a program. Furthermore, P70 to P73 function as I/O pins of UART2, P71 function as input pin of timer B5, and P74 and P75 P60 to P67 I/O port P6 Input/output VCC1 P70 to P77 I/O port P7 Input/output VCC1 P80 to P84 I/O port P80 to P84 Input/output VCC1 (P80 to P84) function as I/O pin of multi-master I2C bus. P80 to P84, P86, and P87 are I/O ports with the same functions as P0. When selected by a program, P80 to P81 function as I/O pins of timer A4, P82 to P84 function input pin of INT interrupt. And, P84 also function as output pin for remote control. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 8 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 1.5 Pin Description (3) 1. DESCRIPTION Pin name P86, P87, P85 Signal name I/O port P86 I/O port P87 I/O port P85 I/O type Input/output Input/output Input Power supply VCC2 (P85 to P87) Function P86 and P87 that when selected in a program, both can function as I/O pins for sub clock oscillation circuit. In that case, connect crystal resonator between P86 (XCOUT pin) and P87 (XCIN pin). P85 is an input-only port shared with NMI. NMI interrupt is generated when input on this pin changes state from high to low. NMI function cannot be disabled in a program. Pull-up resistor cannot be set for this pin. This is an 8-bit I/O port equivalent to P0. Pins in this port also function as SI/O3 and SI/O4 of I/O pins, Timer B0 to B4 input pins, A/D converter input pins, A/D trigger input pins, or remote control input pins as selected by program. Analog power supply pin. Apply the same potential as VCC2 to the VDD2 pin. Apply 0 V to the VSS2 pin. P90 to P97 I/O port P9 Input/output VCC2 VDD2, VSS2 CVIN SYNCIN STARTB LP3 LP4 VCC OFF M1 TEST1 Power supply input Composite video signal input 1 Composite video signal input 2 Oscillation selection input Filter output 2 Filter output 3 VCC1 Power supply input select Mode selection input (M1 input) Test input Input Input Input output output Input Input Input VCC2 VCC2 VCC2 VDD2 VDD2 VCC2 VCC2 VCC2 This pin inputs the external composite video signal. Data-acquisition slices this signal internally by setting. This pin inputs the external composite video signal. Sync.-separate circuit devides this signal internally. This pin selects the oscillation circuit. XIN-XOUT circuit is selected when this pin is "L"; XCIN-XCOUT circuit is selected when this pin is "H". This is a filter output pin 2 (for VPS). This is a filter output pin 3 (for PDC). Normally, please input "L" level. When VCC1 power supply is off, please input "H" level. Connect it to the VSS.In the mask ROM version, connect this pin to the VSS or the VCC2. This is a test pin. Connect a capacitor. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 9 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 1. DESCRIPTION 1.6 Memory Figure 1.4 is a memory map of M306H7MG-XXXFP/MC-XXXFP/FCFP. The address space extends the 1M bytes from address 0000016 to FFFFF16. The internal ROM is allocated in a lower address direction beginning with address FFFFF16. An internal ROM of M306H7MC-XXXFP, for instance, is allocated to the addresses from E000016 to FFFFF16. The fixed interrupt vector table is allocated to the addresses from FFFDC16 to FFFFF16. Therefore, store the start address of each interrupt routine here. The internal RAM is allocated in an upper address direction beginning with address 0040016. An internal RAM of M306H7MC-XXXFP, for instance, is allocated to the addresses from 0040016 to 017FF16. In addition to storing data, the internal RAM also stores the stack used when calling subroutines and when interrupts are generated. SFR is allocated to the addresses from 0000016 to 003FF16. Peripheral function control registers are located here. Of SFR, any area which has no functions allocated is reserved for future use and cannot be used by users. The special page vector table is allocated to the addresses from FFE0016 to FFFDB16. This vector is used by the JMPS or JSRS instruction. For details, refer to the "M16C/60 and M16C/20 Series Software Manual." In memory expansion and microprocessor modes, some areas are reserved for future use and cannot be used by users. 0000016 SFR 0040016 Internal RAM XXXXX16 FFE0016 Special page vector table FFFDC16 Undefined instruction Overflow BRK instruction Address match Single step Size 5K bytes 8K bytes Internal RAM Address XXXXX16 17FF16 23FF16 Size Internal ROM Address YYYYY16 E000016 C000016 FFFFF16 YYYYY16 Internal ROM FFFFF16 Watchdog timer DBC NMI Reset 128K bytes 256K bytes Figure 1.4 Memory Map Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 10 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 2. CENTRAL PROCESSING UNIT (CPU) 2. Central Processing Unit (CPU) Figure 2.1 shows the CPU registers. The CPU has 13 registers. Of these, R0, R1, R2, R3, A0, A1 and FB comprise a register bank. There are two register banks. b31 b15 b8b7 b0 R2 R3 R0H(R0's high bits) R0L(R0's low bits) R1H(R1's high bits) R1L(R1's low bits) R2 R3 A0 A1 FB Address registers (Note) Frame base registers (Note) b0 Data registers (Note) b19 b15 INTBH INTBL Interrupt table register The upper 4 bits of INTB are INTBH and the lower 16 bits of INTB are INTBL. b19 b0 PC b15 b0 Program counter USP ISP SB b15 b0 User stack pointer Interrupt stack pointer Static base register FLG b15 b8 b7 b0 Flag register IPL U I OB SZ DC Carry flag Debug flag Zero flag Sign flag Register bank select flag Overflow flag Interrupt enable flag Stack pointer select flag Reserved area Processor interrupt priority level Reserved area Note: These registers comprise a register bank. There are two register banks. Figure 2.1 CPU registers 2.1 Data Registers (R0, R1, R2 and R3) The R0 register consists of 16 bits, and is used mainly for transfers and arithmetic/logic operations. R1 to R3 are the same as R0. The R0 register can be separated between high (R0H) and low (R0L) for use as two 8-bit data registers. R1H and R1L are the same as R0H and R0L. Conversely, R2 and R0 can be combined for use as a 32- bit data register (R2R0). R3R1 is the same as R2R0. 2.2 Address Registers (A0 and A1) The register A0 consists of 16 bits, and is used for address register indirect addressing and address register relative addressing. They also are used for transfers and logic/logic operations. A1 is the same as A0. In some instructions, registers A1 and A0 can be combined for use as a 32-bit address register (A1A0). Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 11 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 2. CENTRAL PROCESSING UNIT (CPU) 2.3 2.4 2.5 2.6 Frame Base Register (FB) Interrupt Table Register (INTB) Program Counter (PC) User Stack Pointer (USP) and Interrupt Stack Pointer (ISP) FB is configured with 16 bits, and is used for FB relative addressing. INTB is configured with 20 bits, indicating the start address of an interrupt vector table. PC is configured with 20 bits, indicating the address of an instruction to be executed. Stack pointer (SP) comes in two types: USP and ISP, each configured with 16 bits. Your desired type of stack pointer (USP or ISP) can be selected by the U flag of FLG. 2.7 2.8 Static Base Register (SB) Flag Register (FLG) FLG consists of 11 bits, indicating the CPU status. SB is configured with 16 bits, and is used for SB relative addressing. * Carry Flag (C Flag) This flag retains a carry, borrow, or shift-out bit that has occurred in the arithmetic/logic unit. * Debug Flag (D Flag) The D flag is used exclusively for debugging purpose. During normal use, it must be set to "0". * Zero Flag (Z Flag) This flag is set to "1" when an arithmetic operation resulted in 0; otherwise, it is "0". * Sign Flag (S Flag) This flag is set to "1" when an arithmetic operation resulted in a negative value; otherwise, it is "0". * Register Bank Select Flag (B Flag) Register bank 0 is selected when this flag is "0" ; register bank 1 is selected when this flag is "1". * Overflow Flag (O Flag) This flag is set to "1" when the operation resulted in an overflow; otherwise, it is "0". * Interrupt Enable Flag (I Flag) This flag enables a maskable interrupt. Maskable interrupts are disabled when the I flag is "0", and are enabled when the I flag is "1". The I flag is cleared to "0" when the interrupt request is accepted. * Stack Pointer Select Flag (U Flag) ISP is selected when the U flag is "0"; USP is selected when the U flag is "1". The U flag is cleared to "0" when a hardware interrupt request is accepted or an INT instruction for software interrupt Nos. 0 to 31 is executed. * Processor Interrupt Priority Level (IPL) IPL is configured with three bits, for specification of up to eight processor interrupt priority levels from level 0 to level 7. If a requested interrupt has priority greater than IPL, the interrupt is enabled. * Reserved Area When write to this bit, write "0". When read, its content is indeterminate. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 12 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET 3. 3.1 Reset Hardware Reset There are three types of resets: a hardware reset, a software reset, and a watchdog timer reset. A reset is applied using the RESET pin. When an "L" signal is applied to the RESET pin while the power supply voltage is within the recommended operating condition, the pins are initialized (see Table 3.1). The oscillation circuit is initialized and the main clock starts oscillating. When the input level at the RESET pin is released from "L" to "H", the CPU and SFR are initialized, and the program is executed starting from the address indicated by the reset vector. The internal RAM is not initialized. If the RESET pin is pulled "L" while writing to the internal RAM, the internal RAM becomes indeterminate. Figure 3.1 shows the example reset circuit. Figure 3.2 shows the reset sequence. Table 3.1 shows the statuses of the other pins while the RESET pin is "L". Figure 3.3 shows the CPU register status after reset. Refer to "SFR" for SFR status after reset. 1. When the power supply is stable * When STARTB pin = "L" (1) Apply an "L" signal to the RESET pin. (2) Apply a clock for 20 cycles or more to the XIN pin. (3) Apply an "H" signal to the RESET pin. * When STARTB pin = "H" (1) Apply an "L" signal to the RESET pin. (2) Apply a clock for 20 cycles or more to the XCIN pin. (3) Apply an "H" signal to the RESET pin. 2. Power on * When STARTB pin = "L" (1) Apply an "L" signal to the RESET pin. (2) Let the power supply voltage increase until it meets the recommended operating condition. (3) Wait td(P-R) or more until the internal power supply is stabilized. (4) Apply a clock for 20 cycles or more to the XIN pin. (5) Apply an "H" signal to the RESET pin. * When STARTB pin = "H" (1) Apply an "L" signal to the RESET pin. (2) Let the power supply voltage increase until it meets the recommended operating condition. (3) Wait td(P-R) or more until the internal power supply is stabilized. (4) Apply a clock for 20 cycles or more to the XCIN pin. (5) Apply an "H" signal to the RESET pin. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 13 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET VCC2 0V RESET VCC2 RESET 0V Recommended operating voltage Equal to or less than 0.2 VCC2 Equal to or less than 0.2 VCC2 Apply the clock of 20 cycles or more to the td(P-R) + XIN or XCIN pin. (Note 1) Notes 1: When the STARTB pin=L, apply the clock of 20 cycles or more to the XIN pin. When the STARTB pin=H, apply the clock of 20 cycles or more to the XCIN pin. Notes 2: If VCC1 VCC2, the VCC1 voltage must be lower than that of VCC2 when the power is being turned on or off. Figure 3.1 Example Reset Circuit 3.2 Software Reset When the PM03 bit in the PM0 register is set to "1" (microcomputer reset), the microcomputer has its pins, CPU, and SFR initialized. Then the program is executed starting from the address indicated by the reset vector. Select the main clock for the CPU clock source, and set the PM03 bit to "1" with main clock oscillation satisfactorily stable. At software reset, some SFR's are not initialized. Refer to "SFR". Also, since the PM01 to PM00 bits in the PM0 register are not initialized, the processor mode remains unchanged. 3.3 Watchdog Timer Reset Where the PM12 bit in the PM1 register is "1" (reset when watchdog timer underflows), the microcomputer initializes its pins, CPU and SFR if the watchdog timer underflows. Then the program is executed starting from the address indicated by the reset vector. At watchdog timer reset, some SFR's are not initialized. Refer to "SFR". Also, since the PM01 to PM00 bits in the PM0 register are not initialized, the processor mode remains unchanged. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 14 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET VCC XIN / XCIN td(P-R) More than 20 cycles are needed (Note) RESET BCLK 28 cycles BCLK Single chip mode Address FFFFC16 FFFFE16 Content of reset vector Note : When the STARTB pin= "L", apply the clock of 20 cycles or more to the XIN pin after waiting for td(P-R) until the internal power supply is stabilized. When the STARTB pin= "H", apply the clock of 20 cycles or more to the XCIN pin after waiting for td(P-R) until the internal power supply is stabilized. Figure 3.2 Reset Sequence Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 15 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 3.1 Pin Status When RESET Pin Level is "L Status Pin name P0 P1 P2, P3, P40 to P43 P44 P45 to P47 P50 P51 P52 P53 P54 CNVSS = VCC (Note) CNVSS = VSS BYTE = VSS Input port Input port Input port Input port Input port Input port Input port Input port Input port Input port Data input Data input Address output (undefined) CS0 output ("H" is output) Input port (Pulled high) WR output ("H" is output) BHE output (undefined) RD output ("H" is output) BCLK output BYTE = VCC Data input Input port Address output (undefined) CS0 output ("H" is output) Input port (Pulled high) WR output ("H" is output) BHE output (undefined) RD output ("H" is output) BCLK output 3. RESET HLDA output (The output value HLDA output (The output value depends on the input to the depends on the input to the HOLD pin) HOLD pin) HOLD input ALE output ("L" is output) RDY input Input port HOLD input ALE output ("L" is output) RDY input Input port P55 P56 P57 Input port Input port Input port P6, P7, P80 to P84, Input port P86, P87, P9 Note : Do not set CNVss=Vcc for this product. b15 b0 000016 000016 000016 000016 000016 000016 000016 Data register(R0) Data register(R1) Data register(R2) Data register(R3) Address register(A0) Address register(A1) Frame base register(FB) b0 b19 0000016 Content of addresses FFFFE16 to FFFFC16 b15 b0 Interrupt table register(INTB) Program counter(PC) 000016 000016 000016 b15 b0 User stack pointer(USP) Interrupt stack pointer(ISP) Static base register(SB) 000016 b15 b8 b7 b0 Flag register(FLG) IPL UI OBS Z DC Figure 3.3 CPU Register Status After Reset Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 16 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET 3.4 Address 000016 000116 000216 000316 000416 000516 000616 000716 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16 001016 001116 001216 001316 001416 001516 001616 001716 001816 001916 001A16 001B16 001C16 001D16 001E16 001F16 002016 002116 002216 002316 002416 002516 002616 002716 002816 002916 002A16 002B16 002C16 002D16 002E16 002F16 003016 003116 003216 003316 003416 003516 003616 003716 003816 003916 003A16 003B16 003C16 003D16 003E16 003F16 SFR Register (Note 1) Symbol After reset Processor mode register 0 Processor mode register 1 System clock control register 0 System clock control register 1 Address match interrupt enable register Protect register (Note 2) PM0 PM1 CM0 CM1 AIER PRCR 000000002 000010002 010010002(the STARTB pin is "L") 011110002(the STARTB pin is "H") 001000002 XXXXXX002 XX0000002 Watchdog timer start register Watchdog timer control register Address match interrupt register 0 WDTS WDC RMAD0 XX16 00XXXXXX2(Note 3) 0016 0016 X016 0016 0016 X016 Address match interrupt register 1 RMAD1 Processor mode register 2 DMA0 source pointer PM2 SAR0 XXX000002 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 DMA0 destination pointer DAR0 DMA0 transfer counter TCR0 DMA0 control register DM0CON 00000X002 DMA1 source pointer SAR1 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 DMA1 destination pointer DAR1 DMA1 transfer counter TCR1 DMA1 control register DM1CON 00000X002 Note 1: The blank areas are reserved and cannot be accessed by users. Note 2: The PM00 and PM01 bits do not change at software reset, watchdog timer reset and oscillation stop detection reset. Note 3: The WDC5 bit is "0" (cold start) immediately after power-on. It can only be set to "1" in a program. X : Undefined Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 17 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET Address 004016 004116 004216 004316 004416 004516 004616 004716 004816 004916 004A16 004B16 004C16 004D16 004E16 004F16 005016 005116 005216 005316 005416 005516 005616 005716 005816 005916 005A16 005B16 005C16 005D16 005E16 005F16 006016 006116 006216 006316 006416 006516 006616 006716 006816 006916 006A16 006B16 006C16 006D16 006E16 006F16 007016 007116 007216 007316 007416 007516 007616 007716 007816 007916 007A16 007B16 007C16 007D16 007E16 007F16 Register Symbol After reset INT3 interrupt control register Timer B5/SLICE ON interrupt control register Timer B4/Remote control interrupt control register, UART1 BUS collision detection interrupt control register Timer B3/HINT interrupt control register, UART0 BUS collision detection interrupt control register INT3IC TB5IC TB4IC, U1BCNIC TB3IC, U0BCNIC XX00X0002 XXXXX0002 XXXXX0002 XXXXX0002 XX00X0002 XX00X0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XX00X0002 XX00X0002 XX00X0002 SI/O4 interrupt control register, INT5 interrupt control register SI/O3 interrupt control register, INT4 interrupt control register UART2 Bus collision detection interrupt control register DMA0 interrupt control register DMA1 interrupt control register A/D conversion interrupt control register UART2 transmit interrupt control register UART2 receive interrupt control register UART0 transmit interrupt control register UART0 receive interrupt control register UART1 transmit interrupt control register UART1 receive interrupt control register S4IC, INT5IC S3IC, INT4IC BCNIC DM0IC DM1IC ADIC S2TIC S2RIC S0TIC S0RIC S1TIC S1RIC TA0IC TA1IC TA2IC TA3IC TA4IC TB0IC TB1IC TB2IC INT0IC INT1IC INT2IC Timer A0 interrupt control register Timer A1 interrupt control register Timer A2 interrupt control register Timer A3 interrupt control register Timer A4 interrupt control register Timer B0 interrupt control register Timer B1 interrupt control register Timer B2/Clock timer interrupt control register INT0 interrupt control register INT1 interrupt control register INT2 interrupt control register Note :The blank areas are reserved and cannot be accessed by users. X : Undefined Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 18 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET Address 008016 008116 008216 008316 008416 008516 008616 Register Symbol After reset ~ 01B016 01B116 01B216 01B316 01B416 01B516 01B616 01B716 01B816 01B916 01BA16 01BB16 01BC16 01BD16 01BE16 01BF16 ~ ~ Flash memory control register 1 Flash memory control register 0 Address match interrupt register 2 (Note 2) (Note 2) FMR1 FMR0 RMAD2 0X00XX0X2 XX0000012 0016 0016 X016 XXXXXX002 0016 0016 X016 Address match interrupt enable register 2 Address match interrupt register 3 AIER2 RMAD3 ~ 020016 020116 ~ Remote control transmission buffer register RMTTMHL 0016 0016 ~ 020E16 020F16 021016 021116 021216 021316 021416 021516 021616 021716 021816 021916 021A16 021B16 021C16 021D16 021E16 021F16 025016 ~ Slice RAM address control register Slice RAM data control register Address control register for CRC registers Data control register for CRC registers Address control register for extended registers Data control register for extended registers Humming 8/4 register Humming 24/18 register 0 Humming 24/18 register 1 SA SD CA CD DA DD HM8 HM0 HM1 0016 0016 0016 0016 0016 0016 0016 0016 0016 ~ 025916 025A16 025B16 025C16 025D16 025E16 025F16 ~ Peripheral clock select register PCLKR 000000112 ~ 02D616 02D716 ~ I2C0 interrupt control register Reserved register EXTIICINT EXTREG02D7 0016 0016 ~ 02E016 02E116 02E216 02E316 02E416 02E516 02E616 I 2C data shift register I 2C address register I 2C states register I 2C control register I 2C clock control register Reserved register I 2C transmit buffer register IIC0S0 IIC0S0D IIC0S1 IIC0S1D IIC0S2 REVREG02E5 IIC0S0S Undefined 0016 0001000?2 0016 0016 00?000002 Undefined ~ 0330 16 0331 16 0332 16 033316 Note 1: The blank areas are reserved and cannot be accessed by users. Note 2: This register is included in the flash memory version. X : Undefined Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 19 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET Address 034016 034116 034216 034316 034416 034516 034616 034716 034816 034916 034A16 034B16 034C16 034D16 034E16 034F16 035016 035116 035216 035316 035416 035516 035616 035716 035816 035916 035A16 035B16 035C16 035D16 035E16 035F16 036016 036116 036216 036316 036416 036516 036616 036716 036816 036916 036A16 036B16 036C16 036D16 036E16 036F16 037016 037116 037216 037316 037416 037516 037616 037716 037816 037916 037A16 037B16 037C16 037D16 037E16 037F16 Register Timer B3, 4, 5 count start flag Symbol TBSR After reset 000XXXXX2 Timer B3 register Timer B4 register Timer B5 register TB3 TB4 TB5 XX16 XX16 XX16 XX16 XX16 XX16 Timer B3 mode register Timer B4 mode register Timer B5 mode register Interrupt cause select register 2 Interrupt cause select register SI/O3 transmit/receive register SI/O3 control register SI/O3 bit rate generator register SI/O4 transmit/receive register SI/O4 control register SI/O4 bit rate generator register TB3MR TB4MR TB5MR IFSR2A IFSR S3TRR S3C S3BRG S4TRR S4C S4BRG 00XX00002 00XX00002 00XX00002 00XXXXXX2 0016 XX16 010000002 XX16 XX16 010000002 XX16 UART0 special mode register 4 UART0 special mode register 3 UART0 special mode register 2 UART0 special mode register UART1 special mode register 4 UART1 special mode register 3 UART1 special mode register 2 UART1 special mode register UART2 special mode register 4 UART2 special mode register 3 UART2 special mode register 2 UART2 special mode register UART2 transmit/receive mode register UART2 bit rate generator UART2 transmit buffer register UART2 transmit/receive control register 0 UART2 transmit/receive control register 1 UART2 receive buffer register U0SMR4 U0SMR3 U0SMR2 U0SMR U1SMR4 U1SMR3 U1SMR2 U1SMR U2SMR4 U2SMR3 U2SMR2 U2SMR U2MR U2BRG U2TB U2C0 U2C1 U2RB 0016 000X0X0X2 X00000002 X00000002 0016 000X0X0X2 X00000002 X00000002 0016 000X0X0X2 X00000002 X00000002 0016 XX16 XXXXXXXX2 XXXXXXXX2 000010002 000000102 XXXXXXXX2 XXXXXXXX2 Note : The blank areas are reserved and cannot be accessed by users. X : Undefined Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 20 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET Address 038016 038116 038216 038316 038416 038516 038616 038716 038816 038916 038A16 038B16 038C16 038D16 038E16 038F16 039016 039116 039216 039316 039416 039516 039616 039716 039816 039916 039A16 039B16 039C16 039D16 039E16 039F16 03A016 03A116 03A216 03A316 03A416 03A516 03A616 03A716 03A816 03A916 03AA16 03AB16 03AC16 03AD16 03AE16 03AF16 03B016 03B116 03B216 03B316 03B416 03B516 03B616 03B716 03B816 03B916 03BA16 03BB16 03BC16 03BD16 03BE16 03BF16 Register Count start flag Clock prescaler reset flag One-shot start flag Trigger select register Up-down flag Timer A0 register Timer A1 register Timer A2 register Timer A3 register Timer A4 register Timer B0 register Timer B1 register Timer B2 register Timer A0 mode register Timer A1 mode register Timer A2 mode register Timer A3 mode register Timer A4 mode register Timer B0 mode register Timer B1 mode register Timer B2 mode register Symbol TABSR CPSRF ONSF TRGSR UDF TA0 TA1 TA2 TA3 TA4 TB0 TB1 TB2 TA0MR TA1MR TA2MR TA3MR TA4MR TB0MR TB1MR TB2MR After reset 0016 0XXXXXXX2 0016 0016 0016 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 XX16 0016 0016 0016 0016 0016 00XX00002 00XX00002 00XX00002 UART0 transmit/receive mode register UART0 bit rate generator register UART0 transmit buffer register UART0 transmit/receive control register 0 UART0 transmit/receive control register 1 U0MR U0BRG U0TB U0C0 U0C1 U0RB U1MR U1BRG U1TB U1C0 U1C1 U1RB UCON UART0 receive buffer register UART1 transmit/receive mode register UART1 bit rate generator UART1 transmit buffer register UART1 transmit/receive control register 0 UART1 transmit/receive control register 1 UART1 receive buffer register UART transmit/receive control register 2 0016 XX16 XXXXXXXX2 XXXXXXXX2 000010002 000000102 XXXXXXXX2 XXXXXXXX2 0016 XX16 XXXXXXXX2 XXXXXXXX2 000010002 000000102 XXXXXXXX2 XXXXXXXX2 X00000002 DMA0 request cause select register DMA1 request cause select register CRC data register CRC input register DM0SL DM1SL CRCD CRCIN 0016 0016 XX16 XX16 XX16 Note : The blank areas are reserved and cannot be accessed by users. X : Undefined Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 21 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET Address 03C016 03C116 03C216 03C316 03C416 03C516 03C616 03C716 03C816 03C916 03CA16 03CB16 03CC16 03CD16 03CE16 03CF16 03D016 03D116 03D216 03D316 03D416 03D516 03D616 03D716 03D816 03D916 03DA16 03DB16 03DC16 03DD16 03DE16 03DF16 03E016 03E116 03E216 03E316 03E416 03E516 03E616 03E716 03E816 03E916 03EA16 03EB16 03EC16 03ED16 03EE16 03EF16 03F016 03F116 03F216 03F316 03F416 03F516 03F616 03F716 03F816 03F916 03FA16 03FB16 03FC16 03FD16 03FE16 03FF16 Register A/D register 0 A/D register 1 A/D register 2 A/D register 3 A/D register 4 A/D register 5 A/D register 6 A/D register 7 Symbol AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 After reset XXXXXXXX2 XXXXXXXX2 XXXXXXXX2 XXXXXXXX2 XXXXXXXX2 XXXXXXXX2 XXXXXXXX2 XXXXXXXX2 A/D control register 2 A/D control register 0 A/D control register 1 ADCON2 ADCON0 ADCON1 0016 00000XXX2 0016 Port P0 register Port P1 register Port P0 direction register Port P1 direction register Port P2 register Port P3 register Port P2 direction register Port P3 direction register Port P4 register Port P5 register Port P4 direction register Port P5 direction register Port P6 register Port P7 register Port P6 direction register Port P7 direction register Port P8 register Port P9 register Port P8 direction register Port P9 direction register Port P10 register P0 P1 PD0 PD1 P2 P3 PD2 PD3 P4 P5 PD4 PD5 P6 P7 PD6 PD7 P8 P9 PD8 PD9 P10 XX16 XX16 0016 0016 XX16 XX16 0016 0016 XX16 XX16 0016 0016 XX16 XX16 0016 0016 XX16 XX16 00X000002 0016 XX16 Pull-up control register 0 Pull-up control register 1 Pull-up control register 2 Port control register PUR0 PUR1 PUR2 PCR 0016 000000002 0016 0016 Note 1: The blank areas are reserved and cannot be accessed by users. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 22 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET Processor mode register 0 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 Symbol PM0 Address 000416 After reset 000000002 (CNVSS pin = "L") Bit symbol PM00 PM01 (b2) Bit name Processor mode bit b1 b0 Function 0 0: Single-chip mode 0 1: Memory expansion mode 1 0: Must not be set 1 1: Microprocessor mode Must set to "0". Setting this bit to "1" resets the microcomputer. When read, its content is "0". Must set to "0". RW RW RW RW Reserved bit PM03 Software reset bit RW (b7-b4) Reserved bits RW Note 1: Write to this register after setting the PRC1 bit in the PRCR register to "1" (write enable). Figure 3.4 PM0 Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 23 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. RESET Processor mode register 1 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 0000 0 0 Symbol PM1 Address 000516 After reset 0X0010002 Bit symbol (b1-b0) PM12 (b6-b3) PM17 Bit name Reserved bit Watchdog timer function select bit Reserved bit Wait bit (Note 3) Function Must set to "0". 0 : Watchdog timer interrupt 1 : Watchdog timer reset (Note 2) Must set to "0". 0 : No wait state 1 : With wait state (1 wait) RW RW RW RW RW Note 1: Write to this register after setting the PRC1 bit in the PRCR register to "1" (write enable). Note 2: PM12 bit is set to "1" by writing a "1" in a program. (Writing a "0" has no effect.) Note 3: When PM17 bit is set to "1" (with wait state), one wait state is inserted when accessing internal RAM or internal ROM. Figure 3.5 PM1 Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 24 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT 4. Clock Generation Circuit The clock generation circuit contains two oscillator circuits as follows: (1) Main clock oscillation circuit (2) Sub clock oscillation circuit Table 4.1 lists the clock generation circuit specifications. Figure 4.1 shows the clock generation circuit. Figures 4.2 to 4.4 show the clock-related registers. Table 4.1 Item Use of clock CPU registers Sub clock oscillation circuit * CPU clock source *CPU clock source * Peripheral function * Timer A, B's clock source clock source Main clock oscillation circuit Clock frequency Usable oscillator 0 to 16 MHz (Note 3) * Ceramic oscillator * Crystal oscillator (Note 2) XIN, XOUT 32.768 kHz * Crystal oscillator Pins to connect oscillator Oscillation stop, restart function XCIN, XCOUT Presence Presence Stopped Oscillator status Oscillating after reset (Note1) Other Externally derived clock can be input Note 1. The state that the STARTB pin is held "L" after reset is shown. The state that the STARTB pin is held "H" after reset is following. Main clock oscillation circuit: Stopped Sub clock oscillation circuit: Oscillating Note 2. If you use "14 Expansion Function (Data acquisition)", be sure to connect a crystal oscillator between the XIN and XOUT pins. Note 3. If you use "14 Expansion Function (Data acquisition)", connect a crystal of 10MHz, 12MHz, 14MHz, or 16MHz. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 25 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT Sub-clock generating circuit XCIN XCOUT CM01-CM00=002 I/O ports PM01-PM00=002, CM01-CM00=012 PM01-PM00=002, CM01-CM00=102 1/32 Sub-clock fC fC32 f1 PCLK0=1 f2 f8 f32 fAD PCLK0=0 CLKOUT PM01-PM00=002, CM01-CM00=112 CM04 START SQ R f1SIO CM07 CM06 CM10=1(stop mode) SQ XIN R XOUT f32SIO Main clock PCLK1=1 f2SIO PCLK1=0 f8SIO ebc a Divider d fC CM07=1 CM02 CM07=0 CPU clock BCLK CM05 Main clock generating circuit S WAIT instruction R Q e a RESET Software reset NMI Interrupt request level judgment output b 1/2 1/2 1/4 1/8 1/2 1/16 1/2 c 1/32 1/2 1/2 CM06=0 CM17-CM16=112 CM06=1 CM06=0 CM17-CM16=102 d CM02, CM04, CM05, CM06 and CM07: CM0 register bits CM10, CM11, CM16 and CM17: CM1 register bits PCLK0, PCLK1: PCLK register bits CM06=0 CM17-CM16=012 CM06=0 CM17-CM16=002 Details of divider Figure 4.1 Clock Generation Circuit Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 26 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT System clock control register 0 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol CM0 Bit symbol CM00 CM01 CM02 CM03 CM04 CM05 CM06 CM07 Address 000616 Bit name Clock output function select bit (Valid only in single-chip mode) WAIT peripheral function clock stop bit (Note 10) After reset (Note 14) 011110002 (STARTB pin = Vcc) 010010002 (STARTB pin = Vss) Function b1 b0 RW RW RW 0 0 : I/O port P57 0 1 : fC output 1 0 : f8 output 1 1 : f32 output 0 : Do not stop peripheral function clock in wait mode 1 : Stop peripheral function clock in wait mode (Note 8) RW XCIN-XCOUT drive capacity 0 : LOW select bit (Note 2) 1 : HIGH Port XC select bit (Note 2) Main clock stop bit (Notes 3, 10, 12, 13) Main clock division select bit 0 (Notes 7, 13) System clock select bit (Notes 6, 10, 11, 12) 0 : I/O port P86, P87 1 : XCIN-XCOUT generation function(Note 9) 0 : On 1 : Off (Note 4, Note5) 0 : CM16 and CM17 valid 1 : Division by 8 mode 0 : Main clock 1 : Sub-clock RW RW RW RW RW Note 1: Write to this register after setting the PRC0 bit of PRCR register to "1" (write enable). Note 2: The CM03 bit is set to "1" (high) when the CM04 bit is set to "0" (I/O port) or the microcomputer goes to a stop mode. Note 3: This bit is provided to stop the main clock when the low power dissipation mode is selected. This bit cannot be used for detection as to whether the main clock stopped or not. To stop the main clock, the following setting is required: (1) Set the CM07 bit to "1" (Sub-clock select) with the sub-clock stably oscillating. (2) Set the CM05 bit to "1" (Stop). Note 4: During external clock input, only the clock oscillation buffer is turned off and clock input is accepted if the sub clock is not chosen as a CPU clock. Note 5: When CM05 bit is set to "1, the XOUT pin goes "H". Furthermore, because the internal feedback resistor remains connected, the XIN pin is pulled "H" to the same level as XOUT via the feedback resistor. Note 6: After setting the CM04 bit to "1" (XCIN-XCOUT oscillator function), wait until the sub-clock oscillates stably before switching the CM07 bit from "0" to "1" (sub-clock). Note 7: When entering stop mode from high or middle speed mode, the CM06 bit is set to "1" (divide-by-8 mode). Note 8: The fC32 clock does not stop. During low speed or low power dissipation mode, do not set this bit to "1" (peripheral clock turned off when in wait mode). Note 9: To use a sub-clock, set this bit to "1". Also make sure ports P8 6 and P87 are directed for input, with no pull-ups. Note 10: When the PM21 bit of PM2 register is set to "1" (clock modification disable), writing to the CM02, CM05, and CM07 bits has no effect. Note 11: If the PM21 bit needs to be set to "1", set the CM07 bit to "0"(main clock) before setting it. Note 12: To use the main clock as the clock source for the CPU clock, follow the procedure below. (1) Set the CM05 bit to "0" (oscillate). (2) Wait until td(M-L) elapses or the main clock oscillation stabilizes, whichever is longer. (3) Set the CM07 bit all to "0". Note 13: When the CM05 bit is set to "1" (main clock turned off), the CM06 bit is fixed to "1" (divide-by-8 mode) and the CM15 bit is fixed to "1" (drive capability high). Note 14: Keep in mind that the values after reset differ by the input voltage at the STARTB pin. Figure 4.2 CM0 Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 27 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT System clock control register 1 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 00 00 Symbol CM1 Bit symbol CM10 Address 000716 Bit name All clock stop control bit (Notes 4, 5) Reserved bit XIN-XOUT drive capacity select bit (Note 2) Main clock division select bit 1 (Note 3) After reset 001000002 Function 0 : Clock on 1 : All clocks off (stop mode) Must set to "0" 0 : LOW 1 : HIGH b7 b6 RW RW RW RW RW RW (b4-b1) CM15 CM16 CM17 0 0 : No division mode 0 1 : Division by 2 mode 1 0 : Division by 4 mode 1 1 : Division by 16 mode Note 1: Write to this register after setting the PRC0 bit of PRCR register to "1" (write enable). Note 2: When entering stop mode from high or middle speed mode, or when the CM05 bit is set to "1" (main clock turned off) in low speed mode, the CM15 bit is set to "1" (drive capability high). Note 3: Effective when the CM06 bit is "0" (CM16 and CM17 bits enable). Note 4: If the CM10 bit is "1" (stop mode), XOUT goes "H" and the internal feedback resistor is disconnected. The XCIN and XCOUT pins are placed in the high-impedance state. Note 5: When the PM21 bit of PM2 register is set to "1" (clock modification disable), writing to the CM10 bits has no effect. Figure 4.3 CM1 Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 28 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT Peripheral clock select register (Note) b7 b6 b5 b4 b3 b2 b1 b0 000000 Symbol PCLKR Address 025E16 When reset 000000112 Bit symbol PCLK0 Bit name Timers A, B clock select bit (Clock source for the timers A and B SI/O clock select bit (Clock source for UART0 to UART2, SI/O3, SI/O4) 0 : f2 1 : f1 Function RW RW PCLK1 0 : f2SIO 1 : f1SIO Must set to "0" RW (b7-b2) Reserved bit RW Note: Write to this register after setting the PRC0 bit of PRCR register to "1" (write enable). Processor mode register 2 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Symbol PM2 Address 001E16 After reset XXX000002 Bit symbol (b0) PM21 Bit name Reserved bit System clock protective bit (Note 2, Note 3) Reserved bit Function Must set to "0" 0 : Clock is protected by PRCR register 1 : Clock modification disabled Must set to "0" RW RW RW (b4-b2) (b7-b5) RW Nothing is assigned. When write, set to "0". When read, its content is indeterminate. Note 1: Write to this register after setting the PRC1 bit of PRCR register to "1" (write enable). Note 2: Once this bit is set to "1", it cannot be cleared to "0" in a program. Note 3: If the PM21 bit is set to "1," writing to the following bits has no effect. CM02 bit of CM0 register CM05 bit of CM0 register (main clock is not halted) CM07 bit of CM0 register (CPU clock source does not change) CM10 bit of CM1 register (stop mode is not entered) Figure 4.4 PCLKR Register and PM2 Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 29 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT 4.1 Oscillator Circuit The following describes the clocks generated by the clock generation circuit. Two oscillation circuits are built in the clock generating circuit, and a main clock or a sub clock can be chosen as a CPU clock by setup of the STARTB pin after reset. 4.1.1 Main Clock This clock is used as the clock source for the CPU and peripheral function clocks. The main clock oscillator circuit is configured by connecting a resonator between the XIN and XOUT pins. The main clock oscillator circuit contains a feedback resistor, which is disconnected from the oscillator circuit during stop mode in order to reduce the amount of power consumed in the chip. The main clock oscillator circuit may also be configured by feeding an externally generated clock to the XIN pin. Figure 4.5 shows the examples of main clock connection circuit. When the level on the STARTB pin is "L", the main clock divided by 8 is selected for the CPU clock (Sub clock turned off) after reset. The power consumption in the chip can be reduced by setting the CM05 bit of CM0 register to "1" (main clock oscillator circuit turned off) after switching the clock source for the CPU clock to a sub clock. In this case, XOUT goes "H". Furthermore, because the internal feedback resistor remains on, XIN is pulled "H" to XOUT via the feedback resistor. Note that if an externally generated clock is fed into the XIN pin, the main clock cannot be turned off by setting the CM05 bit to "1" without selecting sub clock for the CPU clock. If necessary, use an external circuit to turn off the clock. During stop mode, all clocks including the main clock are turned off. Refer to "power control". Microcomputer (Built-in feedback resistor) Microcomputer (Built-in feedback resistor) XIN XOUT (Note) Rd XIN XOUT Open Externally derived clock CIN COUT Vcc Vss Note: Insert a damping resistor if required. The resistance will vary depending on the oscillator and the oscillation drive capacity setting. Use the value recommended by the maker of the oscillator. When the oscillation drive capacity is set to low, check that oscillation is stable. Also, if the oscillator manufacturer's data sheet specifies that a feedback resistor be added external to the chip, insert a feedback resistor between XIN and XOUT following the instruction. Figure 4.5 Examples of Main Clock Connection Circuit Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 30 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT 4.1.2 Sub Clock The sub clock is generated by the sub clock oscillation circuit. This clock is used as the clock source for the CPU clock, as well as the timer A and timer B count sources. In addition, an fc clock with the same frequency as that of the sub clock can be output from the CLKOUT pin. The sub clock oscillator circuit is configured by connecting a crystal resonator between the XCIN and XCOUT pins. The sub clock oscillator circuit contains a feedback resistor, which is disconnected from the oscillator circuit during stop mode in order to reduce the amount of power consumed in the chip. The sub clock oscillator circuit may also be configured by feeding an externally generated clock to the XCIN pin. Figure 4.6 shows the examples of sub clock connection circuit. When the level on the STARTB pin is "L ", the sub clock is turned off after reset. At this time, the feedback resistor is disconnected from the oscillator circuit. To use the sub clock for the CPU clock, set the CM07 bit of CM0 register to "1 " (sub clock) after the sub clock becomes oscillating stably. When a STARTB pin is "H ", the sub clock (XCIN) divided by 8 becomes the CPU clock after reset (the main clock stops). When you use a main clock after this, please shift according to the procedure shown in Fig. 4.7. During stop mode, all clocks including the sub clock are turned off. Refer to "power control". Microcomputer (Built-in feedback resistor) Microcomputer (Built-in feedback resistor) XCIN XCOUT (Note) RCd XCIN XCOUT Open Externally derived clock CCIN CCOUT Vcc Vss Note: Insert a damping resistor if required. The resistance will vary depending on the oscillator and the oscillation drive capacity setting. Use the value recommended by the maker of the oscillator. When the oscillation drive capacity is set to low, check that oscillation is stable. Also, if the oscillator manufacturer's data sheet specifies that a feedback resistor be added external to the chip, insert a feedback resistor between XCIN and XCOUT following the instruction. Figure 4.6 Examples of Sub Clock Connection Circuit Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 31 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT Using the main clock from the sub clock as CPU clock source. Set the CM07 bit to "1" (sub clock). Set the CM05 bit to "0" (oscillating). Waits until the main clock becomes stable. Set the CM07 bit to "0" (main clock). (note1) Set the main clock division ratio. Set the CM17 to the CM16 bits to "002," set the CM06 bit to "0." (CM16 bit and CM17 bit are effective) (notes 2.) END Note 1: Change After the oscillation of the main clock becomes stable enough. Note 2: Setting No division of the main clock is shown. Change CM06 after changing CM17 and CM16. Figure 4.7 Procedure to Use the Main Clock from the Sub Clock as CPU Clock Source Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 32 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT 4.2 4.2.1 CPU Clock and Peripheral Function Clock CPU Clock and BCLK Two type clocks: CPU clock to operate the CPU and peripheral function clocks to operate the peripheral functions. These are operating clocks for the CPU and watchdog timer. The clock source for the CPU clock can be chosen to be the main clock or sub clock. If the main clock is selected as the clock source for the CPU clock, the selected clock source can be divided by 1 (undivided), 2, 4, 8 or 16 to produce the CPU clock. Use the CM06 bit in CM0 register and the CM17 to CM16 bits in CM1 register to select the divide-by-n value. When the level on the STARTB pin is "H", the main clock divided by 8 provides the CPU clock after reset. When the level on the STARTB pin is "L", the sub clock of frequency divided by 8 provides the CPU clock after reset. At this time, the CM04 bit and the CM05 bit of CM0 register become "1" . Note that when entering stop mode from high or middle speed mode, or when the CM05 bit of CM0 register is set to "1" (main clock turned off) in low-speed mode, the CM06 bit of CM0 register is set to "1" (divide-by-8 mode). 4.2.2 Peripheral Function Clock(f1, f2, f8, f32, f1SIO, f2SIO, f8SIO, f32SIO, fAD, fC32) These are operating clocks for the peripheral functions. Of these, fi (i = 1, 2, 8, 32) and fiSIO are derived from the main clock by dividing them by i. The clock fi is used for timers A and B, and fiSIO is used for serial I/O. The f8 and f32 clocks can be output from the CLKOUT pin. The fAD clock is produced from the main clock, and is used for the A/D converter. When the WAIT instruction is executed after setting the CM02 bit of CM0 register to "1" (peripheral function clock turned off during wait mode), or when the microcomputer is in low power dissipation mode, the fi, fiSIO and fAD clocks are turned off. The fC32 clock is produced from the sub clock, and is used for timers A and B. This clock can be used when the sub clock is on. 4.3 Clock Output Function During single-chip mode, the f8, f32 or fC clock can be output from the CLKOUT pin. Use the CM01 to CM00 bits of CM0 register to select. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 33 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT 4.4 Power Control There are three power control modes. For convenience' sake, all modes other than wait and stop modes are referred to as normal operation mode here. 4.4.1 Normal Operation Mode Normal operation mode is further classified into four modes. In normal operation mode, because the CPU clock and the peripheral function clocks both are on, the CPU and the peripheral functions are operating. Power control is exercised by controlling the CPU clock frequency. The higher the CPU clock frequency, the greater the processing capability. The lower the CPU clock frequency, the smaller the power consumption in the chip. If the unnecessary oscillator circuits are turned off, the power consumption is further reduced. Before the clock sources for the CPU clock can be switched over, the new clock source to which switched must be oscillating stably. If the new clock source is the main clock or sub clock, allow a sufficient wait time in a program until it becomes oscillating stably. * High-speed Mode The main clock divided by 1 provides the CPU clock. If the sub clock is on, fC32 can be used as the count source for timers A and B. * Medium-speed Mode The main clock divided by 2, 4, 8 or 16 provides the CPU clock. If the sub clock is on, fC32 can be used as the count source for timers A and B. * Low-speed Mode The sub clock provides the CPU clock. The main clock is used as the clock source for the peripheral function clock. The fC32 clock can be used as the count source for timers A and B. * Low Power Dissipation Mode In this mode, the main clock is turned off after being placed in low speed mode. The sub clock provides the CPU clock. The fC32 clock can be used as the count source for timers A and B. Simultaneously when this mode is selected, the CM06 bit of CM0 register becomes "1" (divided by 8 mode). In the low power dissipation mode, do not change the CM06 bit. Consequently, the medium speed (divided by 8) mode is to be selected when the main clock is operated next. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 34 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT 4.4.2 Wait Mode In wait mode, the CPU clock is turned off, so are the CPU (because operated by the CPU clock) and the watchdog timer. Because the main clock and sub clock are on, the peripheral functions using these clocks keep operating. * Peripheral Function Clock Stop Function If the CM02 bit is "1" (peripheral function clocks turned off during wait mode), the f1, f2, f8, f32, f1SIO, f8SIO, f32SIO and fAD clocks are turned off when in wait mode, with the power consumption reduced that much. However, fC32 remains on. * Entering Wait Mode The microcomputer is placed into wait mode by executing the WAIT instruction. * Pin Status During Wait Mode Pin Status During Wait Mode is shown in Table 4.2. * Exiting Wait Mode The microcomputer is moved out of wait mode by a hardware reset, NMI interrupt or peripheral function interrupt. If the microcomputer is to be moved out of exit wait mode by a hardware reset or NMI interrupt, set the peripheral function interrupt priority ILVL2 to ILVL0 bits to "0002" (interrupts disabled) before executing the WAIT instruction. The peripheral function interrupts are affected by the CM02 bit. If CM02 bit is "0" (peripheral function clocks not turned off during wait mode), all peripheral function interrupts can be used to exit wait mode. If CM02 bit is "1" (peripheral function clocks turned off during wait mode), the peripheral functions using the peripheral function clocks stop operating, so that only the peripheral functions clocked by external signals can be used to exit wait mode. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 35 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 4.2 Pin Status During Wait Mode Pin _______ _______ 4. CLOCK GENERATION CIRCUIT Single-chip mode A0 to A19, D0 to D15, CS0 to CS3, ________ BHE _____ ______ ________ _________ RD, WR, WRL, WRH __________ HLDA,BCLK ALE I/O ports CLKOUT When fC selected When f8, f32 selected Retains status before wait mode Does not stop Does not stop when the CM02 bit is "0". When the CM02 bit is "1", the status immediately prior to entering wait mode is maintained. Table 4.3 Interrupt NMI interrupt Interrupts to Exit Wait Mode CM02=0 Can be used Can be used when operating with internal or external clock Can be used in one-shot mode or single sweep mode Can be used in all modes CM02=1 Can be used Can be used when operating with external clock (Do not use) Can be used in event counter mode or when the count source is fC32 Can be used Serial I/O interrupt A-D conversion interrupt Timer A interrupt Timer B interrupt INT interrupt Can be used Table 4.3 lists the interrupts to exit wait mode. If the microcomputer is to be moved out of wait mode by a peripheral function interrupt, set up the following before executing the WAIT instruction. (1) In the ILVL2 to ILVL0 bits of interrupt control register, set the interrupt priority level of the peripheral function interrupt to be used to exit wait mode. Also, for all of the peripheral function interrupts not used to exit wait mode, set the ILVL2 to ILVL0 bits to "0002" (interrupt disable). (2) Set the I flag to "1". (3) Enable the peripheral function whose interrupt is to be used to exit wait mode. In this case, when an interrupt request is generated and the CPU clock is thereby turned on, an interrupt routine is executed. The CPU clock turned on when exiting wait mode by a peripheral function interrupt is the same CPU clock that was on when the WAIT instruction was executed. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 36 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT 4.4.3 Stop Mode In stop mode, all oscillator circuits are turned off, so are the CPU clock and the peripheral function clocks. Therefore, the CPU and the peripheral functions clocked by these clocks stop operating. The least amount of power is consumed in this mode. If the voltage applied to Vcc pins is VRAM or more, the internal RAM is retained. However, the peripheral functions clocked by external signals keep operating. The following interrupts can be used to exit stop mode. * NMI interrupt * INT interrupt * Timer A, Timer B interrupt (when counting external pulses in event counter mode) * Serial I/O interrupt (when external clock is selected) The internal oscillator circuit of expansion function (Data acquisition / humming function) stops oscillation when expansion register XTAL_VCO, PDC_VCO_ON, VPS_VCO_ON = "L". * Entering Stop Mode The microcomputer is placed into stop mode by setting the CM10 bit of CM1 register to "1" (all clocks turned off). At the same time, the CM06 bit of CM0 register is set to "1" (divide-by-8 mode) and the CM15 bit of CM1 register is set to "1" (main clock oscillator circuit drive capability high). * Pin Status in Stop Mode Table 4.4 lists pin status during stop mode * Exiting Stop Mode The microcomputer is moved out of stop mode by a hardware reset, NMI interrupt or peripheral function interrupt. If the microcomputer is to be moved out of stop mode by a hardware reset or NMI interrupt, set the peripheral function interrupt priority ILVL2 to ILVL0 bits to "0002" (interrupts disable) before setting the CM10 bit to "1". If the microcomputer is to be moved out of stop mode by a peripheral function interrupt, set up the following before setting the CM10 bit to "1". (1) In the ILVL2 to ILVL0 bits of interrupt control register, set the interrupt priority level of the peripheral function interrupt to be used to exit stop mode. Also, for all of the peripheral function interrupts not used to exit stop mode, set the ILVL2 to ILVL0 bits to "0002". (2) Set the I flag to "1". (3) Enable the peripheral function whose interrupt is to be used to exit stop mode. In this case, when an interrupt request is generated and the CPU clock is thereby turned on, an interrupt service routine is executed. Which CPU clock will be used after exiting stop mode by a peripheral function or NMI interrupt is determined by the CPU clock that was on when the microcomputer was placed into stop mode as follows: If the CPU clock before entering stop mode was derived from the sub clock: sub clock If the CPU clock before entering stop mode was derived from the main clock: main clock divide-by-8 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 37 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 4.4 Pin Status in Stop Mode Pin _______ _______ 4. CLOCK GENERATION CIRCUIT Single-chip mode A0 to A19, D0 to D15, CS0 to CS3, ________ BHE _____ ______ ________ _________ RD, WR, WRL, WRH __________ HLDA, BCLK ALE I/O ports CLKOUT When fc selected When f8, f32 selected Retains status before stop mode "H" Retains status before stop mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 38 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT Figure 4.8 shows the state transition from normal operation mode to stop mode and wait mode. Figure 4.9 shows the state transition in normal operation mode. Reset All oscillators stopped WAIT instruction CM10=1 CPU operation stopped Stop mode Interrupt Interrupt CM07=0 CM06=1 CM05=0 CM10=1 (Note 2) Medium-speed mode (divided-by-8 mode) Wait mode Interrupt WAIT instruction Stop mode CM10=1 When low power When dissipation lowmode speed mode High-speed, mediumspeed mode Wait mode Interrupt CM10=1 WAIT instruction Stop mode Interrupt Low-speed, low power dissipation mode Interrupt Wait mode Normal mode Figure 4.8 State Transition to Stop Mode and Wait Mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 39 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT Main clock oscillation High-speed mode CPU clock: f(XIN) Middle-speed mode (divide by 2) CPU clock: f(XIN)/2 Middle-speed mode (divide by 4) CPU clock: f(XIN)/4 Middle-speed mode Middle-speed mode (divide by 8) (divide by 16) CPU clock: f(XIN)/8 CPU clock: f(XIN)/16 CM07=0 CM06=0 CM17=0 CM16=0 CM07=0 CM06=0 CM17=0 CM16=1 CM07=0 CM06=0 CM17=1 CM16=0 CM07=0 CM06=1 CM07=0 CM06=0 CM17=1 CM16=1 CM04=1 CM04=0 High-speed mode CPU clock: f(XIN) Middle-speed mode (divide by 2) CPU clock: f(XIN)/2 Middle-speed mode (divide by 4) CPU clock: f(XIN)/4 Middle-speed mode Middle-speed mode (divide by 8) (divide by 16) CPU clock: f(XIN)/8 CPU clock: f(XIN)/16 CM07=0 CM06=0 CM17=0 CM16=0 CM07=0 CM06=0 CM17=0 CM16=1 CM07=0 CM06=0 CM17=1 CM16=0 CM07=0 CM06=1 CM07=0 CM06=0 CM17=1 CM16=1 CM07=1 (Note 2) CM07=0 (Note 1, Note 3) Low-speed mode CPU clock: f(XCIN) CM07=0 CM05=1 CM05=0 Low power dissipation mode CPU clock: f(XCIN) CM07=0 CM06=1 CM15=1 Sub clock oscillation Notes: 1: Switch clock after oscillation of main clock is sufficiently stable. 2: Switch clock after oscillation of sub-clock is sufficiently stable. 3: Change CM17 and CM16 before changing CM06. 4: Transit in accordance with arrow. Figure 4.9 State Transition in Normal Mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 40 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. CLOCK GENERATION CIRCUIT 4.5 System Clock Protective Function When the main clock is selected for the CPU clock source, this function disables the clock against modifications in order to prevent the CPU clock from becoming halted by run-away. If the PM21 bit of PM2 register is set to "1" (clock modification disabled), the following bits are protected against writes: * CM02, CM05, and CM07 bits in CM0 register * CM10, CM11 bits in CM1 register Before the system clock protective function can be used, the following register settings must be made while the CM05 bit of CM0 register is "0" (main clock oscillating) and CM07 bit is "0" (main clock selected for the CPU clock source): (1) Set the PRC1 bit of PRCR register to "1" (enable writes to PM2 register). (2) Set the PM21 bit of PM2 register to "1" (disable clock modification). (3) Set the PRC1 bit of PRCR register to "0" (disable writes to PM2 register). Do not execute the WAIT instruction when the PM21 bit is "1". Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 41 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 5. PROTECTION 5. Protection In the event that a program runs out of control, this function protects the important registers so that they will not be rewritten easily. Figure 5.1 shows the PRCR register. The following lists the registers protected by the PRCR register. * Registers protected by PRC0 bit: CM0, CM1 and PCLKR registers * Registers protected by PRC1 bit: PM0, PM1 and PM2 registers * Registers protected by PRC2 bit: PD9, S3C and S4C registers Set the PRC2 bit to "1" (write enabled) and then write to any address, and the PRC2 bit will be cleared to "0" (write protected). The registers protected by the PRC2 bit should be changed in the next instruction after setting the PRC2 bit to "1". Make sure no interrupts or DMA transfers will occur between the instruction in which the PRC2 bit is set to "1" and the next instruction. The PRC0 and PRC1 bits are not automatically cleared to "0" by writing to any address. They can only be cleared in a program. Protect register b7 b6 b5 b4 b3 b2 b1 b0 000 Symbol PRCR Bit symbol PRC0 Address 000A16 Bit name Protect bit 0 After reset XX0000002 Function Enable write to CM0, CM1 and PCLKR registers 0 : Write protected 1 : Write enabled Enable write to PM0, PM1 and PM2 registers 0 : Write protected 1 : Write enabled Enable write to PD9, S3C and S4C registers 0 : Write protected 1 : Write enabled RW RW PRC1 Protect bit 1 RW PRC2 Protect bit 2 RW (b5-b3) Reserved bit Must set to "0" RW (b7-b6) Nothing is assigned. When write, set to "0". When read, its content is interdeterminate. Note: The PRC2 bit is set to "0" by writing to any address after setting it to "1". Other bits are not set to "0" by writing to any address, and must therefore be set in a program. Figure 5.1 PRCR Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 42 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6. 6.1 Interrupts Type of Interrupts Figure 6.1 shows types of interrupts. Software (Non-maskable interrupt) Undefined instruction (UND instruction) Overflow (INTO instruction) BRK instruction INT instruction _______ ________ Interrupt NMI Hardware Special (Non-maskable interrupt) DBC (Note 2) Watchdog timer Single step (Note 2) Address match Peripheral function (Note 1) (Maskable interrupt) Note 1: Peripheral function interrupts are generated by the microcomputer's internal functions. Note 2: Do not normally use this interrupt because it is provided exclusively for use by development support tools. Figure 6.1 Interrupts * Maskable Interrupt: An interrupt which can be enabled (disabled) by the interrupt enable flag (I flag) or whose interrupt priority can be changed by priority level. * Non-maskable Interrupt: An interrupt which cannot be enabled (disabled) by the interrupt enable flag (I flag) or whose interrupt priority cannot be changed by priority level. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 43 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.2 Software Interrupts * Undefined Instruction Interrupt An undefined instruction interrupt occurs when executing the UND instruction. * Overflow Interrupt An overflow interrupt occurs when executing the INTO instruction with the O flag set to "1" (the operation resulted in an overflow). The following are instructions whose O flag changes by arithmetic: ABS, ADC, ADCF, ADD, CMP, DIV, DIVU, DIVX, NEG, RMPA, SBB, SHA, SUB * BRK Interrupt A BRK interrupt occurs when executing the BRK instruction. * INT Instruction Interrupt An INT instruction interrupt occurs when executing the INT instruction. Software interrupt Nos. 0 to 63 can be specified for the INT instruction. Because software interrupt Nos. 4 to 31 are assigned to peripheral function interrupts, the same interrupt routine as for peripheral function interrupts can be executed by executing the INT instruction. In software interrupt Nos. 0 to 31, the U flag is saved to the stack during instruction execution and is cleared to "0" (ISP selected) before executing an interrupt sequence. The U flag is restored from the stack when returning from the interrupt routine. In software interrupt Nos. 32 to 63, the U flag does not change state during instruction execution, and the SP then selected is used. A software interrupt occurs when executing certain instructions. Software interrupts are non-maskable interrupts. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 44 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.3 Hardware Interrupts * Special Interrupts Special interrupts are non-maskable interrupts. (1) NMI Interrupt An NMI interrupt is generated when input on the NMI pin changes state from high to low. For details about the NMI interrupt, refer to the section "NMI interrupt". (2) DBC Interrupt Do not normally use this interrupt because it is provided exclusively for use by development support tools. (3) Watchdog Timer Interrupt Generated by the watchdog timer. Once a watchdog timer interrupt is generated, be sure to initialize the watchdog timer. For details about the watchdog timer, refer to the section "watchdog timer". (4) Single-step Interrupt Do not normally use this interrupt because it is provided exclusively for use by development support tools. (5) Address Match Interrupt An address match interrupt is generated immediately before executing the instruction at the address indicated by the RMAD0 to RMAD3 register that corresponds to one of the AIER register's AIER0 or AIER1 bit or the AIER2 register's AIER20 or AIER21 bit which is "1" (address match interrupt enabled). For details about the address match interrupt, refer to the section "address match interrupt". Hardware interrupts are classified into two types -- special interrupts and peripheral function interrupts. * Peripheral Function Interrupts Peripheral function interrupts are maskable interrupts and generated by the microcomputer's internal functions. The interrupt sources for peripheral function interrupts are listed in Table 6.2. For details about the peripheral functions, refer to the description of each peripheral function in this manual. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 45 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.4 Interrupts and Interrupt Vector One interrupt vector consists of 4 bytes. Set the start address of each interrupt routine in the respective interrupt vectors. When an interrupt request is accepted, the CPU branches to the address set in the corresponding interrupt vector. Figure 6.2 shows the interrupt vector. MSB LSB Low address Vector address (L) Mid address 0000 High address 0000 Vector address (H) 0000 Figure 6.2 Interrupt Vector * Fixed Vector Tables The fixed vector tables are allocated to the addresses from FFFDC16 to FFFFF16. Table 6.1 lists the fixed vector tables. In the flash memory version of microcomputer, the vector addresses (H) of fixed vectors are used by the ID code check function. For details, refer to the section "flash memory rewrite disabling function". Table 6.1 Fixed Vector Tables Interrupt source Vector table addresses Address (L) to address (H) Remarks Interrupt on UND instruction Interrupt on INTO instruction If the contents of address FFFE716 is FF16, program execution starts from the address shown by the vector in the relocatable vector table. Reference M16C/60, M16C/20 series software manual Undefined instruction FFFDC16 to FFFDF16 Overflow FFFE016 to FFFE316 BRK instruction FFFE416 to FFFE716 Address match Single step (Note) Watchdog timer ________ DBC (Note) NMI FFFE816 to FFFEB16 FFFEC16 to FFFEF16 FFFF016 to FFFF316 FFFF416 to FFFF716 FFFF816 to FFFFB16 Address match interrupt Watchdog timer _______ NMI interrupt Reset FFFFC16 to FFFFF16 Reset Note: Do not normally use this interrupt because it is provided exclusively for use by development support tools. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 46 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS * Relocatable Vector Tables The 256 bytes beginning with the start address set in the INTB register comprise a reloacatable vector table area. Table 6.2 lists the relocatable vector tables. Setting an even address in the INTB register results in the interrupt sequence being executed faster than in the case of odd addresses. Table 6.2 Relocatable Vector Tables Vector address (Note 1) Address (L) to address (H) +0 to +3 (000016 to 000316) Software interrupt number 0 1 to 3 +16 to +19 (001016 to 001316) +20 to +23 (001416 to 001716) +24 to +27 (001816 to 001B16) +28 to +31 (001C16 to 001F16) +32 to +35 (002016 to 002316) +36 to +39 (002416 to 002716) +40 to +43 (002816 to 002B16) +44 to +47 (002C16 to 002F16) +48 to +51 (003016 to 003316) +56 to +59 (003816 to 003B16) +60 to +63 (003C16 to 003F16) +64 to +67 (004016 to 004316) +68 to +71 (004416 to 004716) +72 to +75 (004816 to 004B16) +76 to +79 (004C16 to 004F16) +80 to +83 (005016 to 005316) +84 to +87 (005416 to 005716) +88 to +91 (005816 to 005B16) +92 to +95 (005C16 to 005F16) +96 to +99 (006016 to 006316) +100 to +103 (006416 to 006716) +104 to +107 (006816 to 006B16) +108 to +111 (006C16 to 006F16) +112 to +115 (007016 to 007316) +116 to +119 (007416 to 007716) +120 to +123 (007816 to 007B16) 4 5 6 Timer Serial I/O 7 8 9 10 11 12 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 to 63 M16C/60, M16C/20 series software manual INT interrupt Timer Serial I/O DMAC Reference M16C/60, M16C/20 series software manual INT interrupt Timer Interrupt source BRK instruction (Note 5) (Reserved) INT3 Timer B5/SLICE ON (Note 7) Timer B4/Remote control, UART1 bus collision detect (Note 4, Note 6, Note 7) Timer B3/HINT, UART0 bus collision detect (Note 4, Note 6, Note 7) SI/O4, INT5 SI/O3, INT4 (Note 2) (Note 2) INT interrupt Serial I/O Serial I/O UART 2 bus collision detection DMA0 DMA1 A/D UART2 transmit, NACK2 (Note 3) UART2 receive, ACK2 (Note 3) UART0 transmit, NACK0 (Note 3) UART0 receive, ACK0 (Note 3) UART1 transmit, NACK1(Note 3) UART1 receive, ACK1 (Note 3) Timer A0 Timer A1 Timer A2 Timer A3 Timer A4/Multi-master I 2 C (Note 9) Timer B0 Timer B1 Timer B2/Clock timer (Note 7) INT0 INT1 A/D converter INT2/Remote control transmission (Note 8) +124 to +127 (007C16 to 007F16) +128 to +131 (008016 to 008316) Software interrupt (Note 5) to +252 to +255 (00FC16 to 00FF16) Notes 1: Address relative to address in INTB . Notes 2: Use the IFSR register's IFSR6 and IFSR7 bits to select. Notes 3: During I2C mode, NACK and ACK interrupts comprise the interrupt source. Notes 4: Use the IFSR2A register's IFSR26 and IFSR27 bits to select. Notes 5: These interrupts cannot be disabled using the I flag. Notes 6: Bus collision detection : During IE mode, this bus collision detection constitutes the cause of an interrupt. During I2C mode, however, a start condition or a stop condition detection constitutes the cause of an interrupt. Notes 7: When you use SLICEON, remote control, HINT and clock timer interruption, refer to address 3616 expansion register of "14. Expansion Function" Notes 8: Please refer to address 3E16 of the expansion register of "14. Expansion Function" when you use the remote control transmission interrupt. Notes 9: Please refer to the I2C0 interrupt control register of "11 multi-master I2C-BUS interface" (address 02D616) when you use multi master I2C interrupt. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 47 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.5 Interrupt Control The following describes how to enable/disable the maskable interrupts, and how to set the priority in which order they are accepted. What is explained here does not apply to nonmaskable interrupts. Use the FLG register's I flag, IPL, and each interrupt control register's ILVL2 to ILVL0 bits to enable/disable the maskable interrupts. Whether an interrupt is requested is indicated by the IR bit in each interrupt control register. Figure 6.3 shows the interrupt control registers. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 48 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS Interrupt control register (Note 2) Symbol TB5IC TB4IC/U1BCNIC (Note 3) TB3IC/U0BCNIC (Note 3) BCNIC DM0IC, DM1IC ADIC S0TIC to S2TIC S0RIC to S2RIC TA0IC to TA4IC TB0IC to TB2IC Address 004516 004616 004716 004A16 004B16, 004C16 004E16 005116, 005316, 004F16 005216, 005416, 005016 005516 to 005916 005A16 to 005C16 After reset XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 XXXXX0002 b7 b6 b5 b4 b3 b2 b1 b0 Bit symbol ILVL0 Bit name Interrupt priority level select bit b2 b1 b0 Function 000: 001: 010: 011: 100: 101: 110: 111: Level 0 (interrupt disabled) Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 RW RW ILVL1 RW ILVL2 RW RW (Note 1) IR Interrupt request bit 0 : Interrupt not requested 1 : Interrupt requested (b7-b4) No functions are assigned. When writing to these bits, write "0". The values in these bits when read are indeterminate. Note 1: This bit can only be reset by writing "0" (Do not write "1"). Note 2: To rewrite the interrupt control registers, do so at a point that does not generate the interrupt request for that register. For details, see the precautions for interrupts. Note 3: Use the IFSR2A register to select. Symbol INT3IC S4IC/INT5IC S3IC/INT4IC INT0IC to INT2IC Address 004416 004816 004916 005D16 to 005F16 After reset XX00X0002 XX00X0002 XX00X0002 XX00X0002 b7 b6 b5 b4 b3 b2 b1 b0 0 Bit symbol ILVL0 Bit name Interrupt priority level select bit b2 b1 b0 Function 0 0 0 : Level 0 (interrupt disabled) 0 0 1 : Level 1 0 1 0 : Level 2 0 1 1 : Level 3 1 0 0 : Level 4 1 0 1 : Level 5 1 1 0 : Level 6 1 1 1 : Level 7 0: Interrupt not requested 1: Interrupt requested 0 : Selects falling edge (Notes 3, 4) 1 : Selects rising edge Must always be set to "0" RW RW ILVL1 RW ILVL2 RW RW (Note 1) RW RW IR Interrupt request bit POL Polarity select bit Reserved bit (b7-b6) No functions are assigned. When writing to these bits, write "0". The values in these bits when read are indeterminate. RW Note 1: This bit can only be reset by writing "0" (Do not write "1"). Note 2: To rewrite the interrupt control register, do so at a point that does not generate the interrupt request for that register. For details, see the precautions for interrupts. Note 3: If the IFSR register's IFSRi bit (i = 0 to 5) is "1" (both edges), set the INTiIC register's POL bit to "0 "(falling edge). Note 4: Set the S3IC or S4IC register's POL bit to "0" (falling edge) when the IFSR register's IFSR6 bit = 0 (SI/O3 selected) or IFSR7 bit = 0 (SI/O4 selected), respectively . Figure 6.3 Interrupt Control Registers Page 49 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.6 I Flag The I flag enables or disables the maskable interrupt. Setting the I flag to "1" (= enabled) enables the maskable interrupt. Setting the I flag to "0" (= disabled) disables all maskable interrupts. 6.7 IR Bit The IR bit is set to "1" (= interrupt requested) when an interrupt request is generated. Then, when the interrupt request is accepted and the CPU branches to the corresponding interrupt vector, the IR bit is cleared to "0" (= interrupt not requested). The IR bit can be cleared to "0" in a program. Note that do not write "1" to this bit. 6.8 ILVL2 to ILVL0 Bits and IPL Interrupt priority levels can be set using the ILVL2 to ILVL0 bits. Table 6.3 shows the settings of interrupt priority levels and Table 6.4 shows the interrupt priority levels enabled by the IPL. The following are conditions under which an interrupt is accepted: * I flag = "1" * IR bit = "1" * interrupt priority level > IPL The I flag, IR bit, ILVL2 to ILVL0 bits and IPL are independent of each other. In no case do they affect one another. Table 6.3 Settings of Interrupt Priority Levels Interrupt priority level Level 0 (interrupt disabled) Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 High Low Priority order Table 6.4 Interrupt Priority Levels Enabled by IPL ILVL2 to ILVL0 bits IPL 0002 0012 0102 0112 1002 1012 1102 1112 Enabled interrupt priority levels 0002 0012 0102 0112 1002 1012 1102 1112 Interrupt levels 1 and above are enabled Interrupt levels 2 and above are enabled Interrupt levels 3 and above are enabled Interrupt levels 4 and above are enabled Interrupt levels 5 and above are enabled Interrupt levels 6 and above are enabled Interrupt levels 7 and above are enabled All maskable interrupts are disabled Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 50 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.9 Interrupt Sequence An interrupt sequence -- what are performed over a period from the instant an interrupt is accepted to the instant the interrupt routine is executed -- is described here. If an interrupt occurs during execution of an instruction, the processor determines its priority when the execution of the instruction is completed, and transfers control to the interrupt sequence from the next cycle. If an interrupt occurs during execution of either the SMOVB, SMOVF, SSTR or RMPA instruction, the processor temporarily suspends the instruction being executed, and transfers control to the interrupt sequence. The CPU behavior during the interrupt sequence is described below. Figure 6.4 shows time required for executing the interrupt sequence. (1) The CPU gets interrupt information (interrupt number and interrupt request priority level) by reading the address 0000016. Then it clears the IR bit for the corresponding interrupt to "0" (interrupt not requested). (2) The FLG register immediately before entering the interrupt sequence is saved to the CPU's internal temporary register(Note 1). (3) The I, D and U flags in the FLG register become as follows: The I flag is cleared to "0" (interrupts disabled). The D flag is cleared to "0" (single-step interrupt disabled). The U flag is cleared to "0" (ISP selected). However, the U flag does not change state if an INT instruction for software interrupt Nos. 32 to 63 is executed. (4) The CPU's internal temporary register (Note 1) is saved to the stack. (5) The PC is saved to the stack. (6) The interrupt priority level of the accepted interrupt is set in the IPL. (7) The start address of the relevant interrupt routine set in the interrupt vector is stored in the PC. After the interrupt sequence is completed, the processor resumes executing instructions from the start address of the interrupt routine. Note: This register cannot be used by user. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 CPU clock Address bus Data bus RD WR Address 000016 Interrupt information Indeterminate (Note 1) Indeterminate (Note 1) Indeterminate (Note 1) SP-2 SP-2 contents SP-4 SP-4 contents vec vec contents vec+2 vec+2 contents PC (Note 2) Note 1 : The indeterminate state depends on the instruction queue buffer. A read cycle occurs when the instruction queue buffer is ready to accept instructions. Note 2 : The WR signal timing shown here is for the case where the stack is located in the internal RAM. Figure 6.4 Time Required for Executing Interrupt Sequence Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 51 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.10 Interrupt Response Time Figure 6.5 shows the interrupt response time. The interrupt response or interrupt acknowledge time denotes a time from when an interrupt request is generated till when the first instruction in the interrupt routine is executed. Specifically, it consists of a time from when an interrupt request is generated till when the instruction then executing is completed ((a) in Figure 6.5) and a time during which the interrupt sequence is executed ((b) in Figure 6.5). Interrupt request generated Interrupt request acknowledged Time Instruction (a) Interrupt sequence (b) Instruction in interrupt routine Interrupt response time (a) A time from when an interrupt request is generated till when the instruction then executing is completed. The length of this time varies with the instruction being executed. The DIVX instruction requires the longest time, which is equal to 30 cycles (without wait state, the divisor being a register). (b) A time during which the interrupt sequence is executed. For details, see the table below. Note, however, that the values in this table must be increased 2 cycles for the DBC interrupt and 1 cycle for the address match and single-step interrupts. Interrupt vector address SP value 16-Bit bus, without wait Even Even Odd Odd Even Odd Even Odd 18 cycles 19 cycles 19 cycles 20 cycles 8-Bit bus, without wait 20 cycles 20 cycles 20 cycles 20 cycles Figure 6.5 Interrupt response time 6.11 Variation of IPL when Interrupt Request is Accepted When a maskable interrupt request is accepted, the interrupt priority level of the accepted interrupt is set in the IPL. When a software interrupt or special interrupt request is accepted, one of the interrupt priority levels listed in Table 6.5 is set in the IPL. Shown in Table 6.5 are the IPL values of software and special interrupts when they are accepted. Table 6.5 IPL Level That is Set to IPL When A Software or Special Interrupt Is Accepted Interrupt sources Watchdog timer, NMI Software, address match, DBC, single-step Level that is set to IPL 7 Not changed Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 52 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.12 Saving Registers In the interrupt sequence, the FLG register and PC are saved to the stack. At this time, the 4 high-order bits of the PC and the 4 high-order (IPL) and 8 low-order bits of the FLG register, 16 bits in total, are saved to the stack first. Next, the 16 low-order bits of the PC are saved. Figure 6.6 shows the stack status before and after an interrupt request is accepted. The other necessary registers must be saved in a program at the beginning of the interrupt routine. Use the PUSHM instruction, and all registers except SP can be saved with a single instruction. Address MSB Stack LSB Address MSB Stack LSB [SP] New SP value m-4 m-3 m-2 m-1 m m+1 Content of previous stack Content of previous stack [SP] SP value before interrupt occurs m-4 m-3 m-2 m-1 m m+1 FLGH PC L PCM FLGL PCH Content of previous stack Content of previous stack Stack status before interrupt request is acknowledged Stack status after interrupt request is acknowledged Figure 6.6 Stack Status Before and After Acceptance of Interrupt Request Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 53 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS The operation of saving registers carried out in the interrupt sequence is dependent on whether the SP(Note), at the time of acceptance of an interrupt request, is even or odd. If the stack pointer (Note) is even, the FLG register and the PC are saved, 16 bits at a time. If odd, they are saved in two steps, 8 bits at a time. Figure 6.7 shows the operation of the saving registers. Note: When any INT instruction in software numbers 32 to 63 has been executed, this is the SP indicated by the U flag. Otherwise, it is the ISP. (1) SP contains even number Address Stack Sequence in which order registers are saved [SP] - 5 (Odd) [SP] - 4 (Even) [SP] - 3(Odd) [SP] - 2 (Even) [SP] - 1(Odd) [SP] (Even) Finished saving registers in two operations. FLGH PCL PCM FLGL PCH (1)Saved simultaneously, all 16 bits (2)Saved simultaneously, all 16 bits (2) SP contains odd number Address Stack Sequence in which order registers are saved [SP] - 5 (Even) [SP] - 4(Odd) [SP] - 3 (Even) [SP] - 2(Odd) [SP] - 1 (Even) [SP] (Odd) Finished saving registers in four operations. FLGH PCL PCM FLGL PCH (3) (4) Saved, 8 bits at a time (1) (2) Note: [SP] denotes the initial value of the SP when interrupt request is acknowledged. After registers are saved, the SP content is [SP] minus 4. Figure 6.7 Operation of Saving Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 54 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.13 Returning from an Interrupt Routine The FLG register and PC in the state in which they were immediately before entering the interrupt sequence are restored from the stack by executing the REIT instruction at the end of the interrupt routine. Thereafter the CPU returns to the program which was being executed before accepting the interrupt request. Return the other registers saved by a program within the interrupt routine using the POPM or similar instruction before executing the REIT instruction 6.14 Interrupt Priority If two or more interrupt requests are generated while executing one instruction, the interrupt request that has the highest priority is accepted. For maskable interrupts (peripheral functions), any desired priority level can be selected using the ILVL2 to ILVL0 bits. However, if two or more maskable interrupts have the same priority level, their interrupt priority is resolved by hardware, with the highest priority interrupt accepted. The watchdog timer and other special interrupts have their priority levels set in hardware. Figure 6.8 shows the priorities of hardware interrupts. Software interrupts are not affected by the interrupt priority. If an instruction is executed, control branches invariably to the interrupt routine. Reset NMI DBC Watchdog timer High Peripheral function Single step Address match Low Figure 6.8 Hardware Interrupt Priority 6.15 Interrupt Priority Resolution Circuit The interrupt priority resolution circuit is used to select the interrupt with the highest priority among those requested. Figure 6.9 shows the circuit that judges the interrupt priority level. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 55 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS Priority level of each interrupt INT1 Timer B2/Clock Timer Timer B0 Timer A3 Timer A1 Timer B4/Remote control, UART1 bus collision INT3 INT2/Remote control transmission INT0 Timer B1 Timer A4/Multi-master I 2 C Timer A2 Timer B3/HINT, UART0 bus collision Timer B5/SLICEON UART1 reception, ACK1 UART0 reception, ACK0 UART2 reception, ACK2 A/D conversion DMA1 UART 2 bus collision SI/O4, INT5 Timer A0 UART1 transmission, NACK1 UART0 transmission, NACK0 UART2 transmission, NACK2 DMA0 Level 0 (initial value) High Priority of peripheral function interrupts (if priority levels are same) Low SI/O3, INT4 IPL Interrupt request level resolution output to clock generating circuit (Fig.4.1) I flag Address match Watchdog timer DBC NMI Interrupt request accepted Figure 6.9 Interrupts Priority Select Circuit Page 56 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.16 INT Interrupt INTi interrupt (i = 0 to 5) is triggered by the edges of external inputs. The edge polarity is selected using the IFSR register's IFSRi bit. INT4 and INT5 share the interrupt vector and interrupt control register with SI/O3 and SI/O4, respectively. To use the INT4 interrupt, set the IFSR register's IFSR6 bit to "1" (= INT4). To use the INT5 interrupt, set the IFSR register's IFSR7 bit to "1" (= INT5). After modifying the IFSR6 or IFSR7 bit, clear the corresponding IR bit to "0" (= interrupt not requested) before enabling the interrupt. INT2 and the remote control transmission, the vector and the interrupt control register are shared. (Please refer to "14. Expansion Function" for details. ) Figure 6.10 shows the IFSR and IFSR2A registers. Interrupt request cause select register b7 b6 b5 b4 b3 b2 b1 b0 Symbol IFSR Bit symbol Address 035F16 After reset 0016 Bit name INT0 interrupt polarity switching bit INT1 interrupt polarity switching bit INT2 interrupt polarity switching bit INT3 interrupt polarity switching bit INT4 interrupt polarity switching bit INT5 interrupt polarity switching bit Interrupt request cause select bit Interrupt request cause select bit Function 0 : One edge 1 : Both edges 0 : One edge 1 : Both edges 0 : One edge 1 : Both edges 0 : One edge 1 : Both edges 0 : One edge 1 : Both edges 0 : One edge 1 : Both edges 0 : SI/O3 1 : INT4 0 : SI/O4 1 : INT5 (Note 1) (Note 1) (Note 1) (Note 1) RW RW RW RW RW RW RW RW RW IFSR0 IFSR1 IFSR2 IFSR3 IFSR4 IFSR5 IFSR6 IFSR7 (Note 1) (Note 1) (Note 2) (Note 2) Note 1: When setting this bit to "1" (= both edges), make sure the INT0IC to INT5IC register's POL bit is set to "0" (= falling edge). Note 2: When setting this bit to "0" (= SI/O3, SI/O4), make sure the S3IC and S4IC registers' POL bit is set to "0" (= falling edge). Interrupt request cause select register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol IFSR2A Bit symbol (b5-b0) IFSR26 Address 035E16 After reset 00XXXXXX2 Bit name Function RW Nothing is assigned. When write, set to "0". When read, their contents are indeterminate. Interrupt request cause select bit (Note 1) Interrupt request cause select bit (Note 2) 0 : Timer B3/HINT 1 : UART0 bus collision detection 0 : Timer B4/Remote control 1 : UART1 bus collision detection RW RW IFSR27 Note 1: Timer B3/HINT and UART0 bus collision detection share the vector and interrupt control register. When using the timer B3/HINT interrupt, clear the IFSR26 bit to "0" (timer B3/HINT). When using UART0 bus collision detection, set the IFSR26 bit to "1". Note 2: Timer B4/Remote control and UART1 bus collision detection share the vector and interrupt control register. When using the timer B4/Remote control interrupt, clear the IFSR27 bit to "0" (timer B4/Remote control). When using UART1 bus collision detection, set the IFSR27 bit to "1". Figure 6.10 IFSR Register and IFSR2A Register Page 57 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS 6.17 NMI Interrupt An NMI interrupt is generated when input on the NMI pin changes state from high to low. The NMI interrupt is a non-maskable interrupt. The input level of this NMI interrupt input pin can be read by accessing the P8 register's P8_5 bit. This pin cannot be used as an input port. 6.18 Address Match Interrupt An address match interrupt request is generated immediately before executing the instruction at the address indicated by the RMADi register (i = 0 to 3). Set the start address of any instruction in the RMADi register. Use the AIER register's AIER0 and AIER1 bits and the AIER2 register's AIER20 and AIER21 bits to enable or disable the interrupt. Note that the address match interrupt is unaffected by the I flag and IPL. For address match interrupts, the value of the PC that is saved to the stack area varies depending on the instruction being executed (refer to "Saving Registers"). (The value of the PC that is saved to the stack area is not the correct return address.) Therefore, follow one of the methods described below to return from the address match interrupt. * Rewrite the content of the stack and then use the REIT instruction to return. * Restore the stack to its previous state before the interrupt request was accepted by using the POP or similar other instruction and then use a jump instruction to return. Table 6.6 shows the value of the PC that is saved to the stack area when an address match interrupt request is accepted. Note that when using the external bus in 8 bits width, no address match interrupts can be used for externa areas. Figure 6.11 shows the AIER, AIER2, and RMAD0 to RMAD3 registers. Table 6.6 Instruction Just Before Execution and Address Stored in Stack When There Occurs Interrupts Instruction at the address indicated by the RMADi register * 16-bit op-code instruction * Instruction shown below among 8-bit operation code instructions ADD.B:S #IMM8,dest SUB.B:S #IMM8,dest AND.B:S #IMM8,dest OR.B:S #IMM8,dest MOV.B:S #IMM8,dest STZ.B:S #IMM8,dest STNZ.B:S #IMM8,dest STZX.B:S #IMM81,#IMM82,dest CMP.B:S #IMM8,dest PUSHM src POPM dest JMPS #IMM8 JSRS #IMM8 MOV.B:S #IMM,dest (However, dest=A0 or A1) Value of the PC that is saved to the stack area The address indicated by the RMADi register +2 Instructions other than the above The address indicated by the RMADi register +1 Value of the PC that is saved to the stack area : Refer to "Saving Registers". Table 6.7 Relationship Between Address Match Interrupt Sources and Associated Registers Address match interrupt sources Address match interrupt enable bit Address match interrupt 0 Address match interrupt 1 Address match interrupt 2 Address match interrupt 3 AIER0 AIER1 AIER20 AIER21 Address match interrupt register RMAD0 RMAD1 RMAD2 RMAD3 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 58 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. INTERRUPTS Address match interrupt enable register b7 b6 b5 b4 b3 b2 b1 b0 Symbol AIER Bit symbol Address 000916 Bit name Address match interrupt 0 enable bit Address match interrupt 1 enable bit After reset XXXXXX002 Function 0 : Interrupt disabled 1 : Interrupt enabled RW AIER0 AIER1 0 : Interrupt disabled 1 : Interrupt enabled RW (b7-b2) Nothing is assigned. When write, set to "0". When read, their contents are indeterminate. Address match interrupt enable register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol AIER2 Bit symbol Address 01BB16 Bit name Address match interrupt 2 enable bit Address match interrupt 3 enable bit After reset XXXXXX002 Function 0 : Interrupt disable 1 : Interrupt enabled RW AIER20 AIER21 RW RW 0 : Interrupt disabled 1 : Interrupt enable (b7-b2) Nothing is assigned. When write, set to "0". When read, their contents are indeterminate. Address match interrupt register i (i = 0 to 3) (b23) b7 (b19) b3 (b16)(b15) b0 b7 (b8) b0 b7 b0 Symbol RMAD0 RMAD1 RMAD2 RMAD3 Address 001216 to 001016 001616 to 001416 01BA16 to 01B816 01BE16 to 01BC16 After reset X0000016 X0000016 X0000016 X0000016 Function Address setting register for address match interrupt Setting range 0000016 to FFFFF16 RW RW Nothing is assigned. When write, set to "0". When read, their contents are indeterminate. Figure 6.11 AIER Register, AIER2 Register and RMAD0 to RMAD3 Registers Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 59 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 7. WATCHDOG TIMER 7. Watchdog Timer The watchdog timer is the function of detecting when the program is out of control. Therefore, we recommend using the watchdog timer to improve reliability of a system. The watchdog timer contains a 15-bit counter which counts down the clock derived by dividing the CPU clock using the prescaler. Whether to generate a watchdog timer interrupt request or apply a watchdog timer reset as an operation to be performed when the watchdog timer underflows after reaching the terminal count can be selected using the PM12 bit of PM1 register. The PM12 bit can only be set to "1" (reset). Once this bit is set to "1", it cannot be set to "0" (watchdog timer interrupt) in a program. Refer to "Watchdog Timer Reset" for the details of watchdog timer reset. When the main clock is selected for CPU clock, the divide-by-N value for the prescaler can be chosen to be 16 or 128 using the WDC7 bit of WDC register. If a sub-clock is selected for CPU clock, the divide-by- N value for the prescaler is always 2 no matter how the WDC7 bit is set. The period of watchdog timer can be calculated as given below. The period of watchdog timer is, however, subject to an error due to the prescaler. With main clock chosen for CPU clock Watchdog timer period = Prescaler dividing (16 or 128) X Watchdog timer count (32768) CPU clock With sub-clock chosen for CPU clock Watchdog timer period = Prescaler dividing (2) X Watchdog timer count (32768) CPU clock For example, when CPU clock = 10 MHz and the divide-by-N value for the prescaler= 16, the watchdog timer period is approx. 52.4 ms. The watchdog timer is initialized by writing to the WDTS register. The prescaler is initialized after reset. Note that the watchdog timer and the prescaler both are inactive after reset, so that the watchdog timer is activated to start counting by writing to the WDTS register. In stop mode, wait mode and hold state, the watchdog timer and prescaler are stopped. Counting is resumed from the held value when the modes or state are released. Figure 7.1 shows the block diagram of the watchdog timer. Figure 7.2 shows the watchdog timer-related registers. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 60 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 7. WATCHDOG TIMER Prescaler CM07 = 0 WDC7 = 0 PM12 = 0 1/16 CPU clock HOLD CM07 = 1 1/128 1/2 CM07 = 0 WDC7 = 1 Watchdog timer interrupt request Watchdog timer PM12 = 1 Reset Write to WDTS register RESET Set to "7FFF16" Figure 7.1 Watchdog Timer Block Diagram Watchdog timer control register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol WDC Bit symbol (b4-b0) WDC5 (b6) WDC7 Address After reset 000F16 00XXXXXX2(Note2) Bit name High-order bit of watchdog timer Cold start / warm start 0 : Cold start discrimination flag (Note 1) 1 : Warm start Reserved bit Prescaler select bit Must set to "0" 0 : Divided by 16 1 : Divided by 128 Function RW RO RW RW RW Note 1: The WDC5 bit is always "1" (warm start) no matter how it is set by writing a "0" or "1". Note 2: The WDC5 bit is "0" (cold start) immediately after power-on. It can only be set to "1" in a program. Watchdog timer start register (Note) b7 b0 Symbol WDTS Address 000E16 After reset Indeterminate RW Function The watchdog timer is initialized and starts counting after a write instruction to WO this register. The watchdog timer value is always initialized to "7FFF16" regardless of whatever value is written. Note : Write to the WDTS register after the watchdog timer interrupt occurs. Figure 7.2 WDC Register and WDTS Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 61 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 8. DMAC 8. DMAC The DMAC (Direct Memory Access Controller) allows data to be transferred without the CPU intervention. Two DMAC channels are included. Each time a DMA request occurs, the DMAC transfers one (8 or 16-bit) data from the source address to the destination address. The DMAC uses the same data bus as used by the CPU. Because the DMAC has higher priority of bus control than the CPU and because it makes use of a cycle steal method, it can transfer one word (16 bits) or one byte (8 bits) of data within a very short time after a DMA request is generated. Figure 8.1 shows the block diagram of the DMAC. Table 8.1 shows the DMAC specifications. Figures 8.2 to 8.4 show the DMAC-related registers. Address bus DMA0 source pointer SAR0(20) (addresses 002216 to 002016) DMA0 destination pointer DAR0 (20) (addresses 002616 to 002416) DMA0 forward address pointer (20) (Note) DMA0 transfer counter reload register TCR0 (16) DMA1 source pointer SAR1 (20) (addresses 003216 to 003016) DMA1 destination pointer DAR1 (20) (addresses 003616 to 003416) (addresses 002916, 002816) DMA0 transfer counter TCR0 (16) DMA1 transfer counter reload register TCR1 (16) DMA1 forward address pointer (20) (Note) (addresses 003916, 003816) DMA1 transfer counter TCR1 (16) DMA latch high-order bits DMA latch low-order bits Data bus low-order bits Data bus high-order bits Note: Pointer is incremented by a DMA request. Figure 8.1 DMAC Block Diagram A DMA request is generated by a write to the DMiSL register (i = 0 to 1)'s DSR bit, as well as by an interrupt request which is generated by any function specified by the DMiSL register's DMS and DSEL3 to DSEL0 bits. However, unlike in the case of interrupt requests, DMA requests are not affected by the I flag and the interrupt control register, so that even when interrupt requests are disabled and no interrupt request can be accepted, DMA requests are always accepted. Furthermore, because the DMAC does not affect interrupts, the interrupt control register's IR bit does not change state due to a DMA transfer. A data transfer is initiated each time a DMA request is generated when the DMiCON register's DMAE bit = "1" (DMA enabled). However, if the cycle in which a DMA request is generated is faster than the DMA transfer cycle, the number of transfer requests generated and the number of times data is transferred may not match. For details, refer to "DMA Requests". Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 62 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 8.1 DMAC Specifications 8. DMAC Item No. of channels Transfer memory space Maximum No. of bytes transferred DMA request factors (Note 1, Note 2) Specification 2 (cycle steal method) * From any address in the 1M bytes space to a fixed address * From a fixed address to any address in the 1M bytes space * From a fixed address to a fixed address 128K bytes (with 16-bit transfers) or 64K bytes (with 8-bit transfers) ________ ________ Channel priority Transfer unit Transfer address direction Transfer mode *Single transfer *Repeat transfer DMA interrupt request generation timing DMA startup DMA shutdown *Single transfer *Repeat transfer Reload timing for forward address pointer and transfer counter Falling edge of INT0 or INT1 ________ ________ Both edge of INT0 or INT1 Timer A0 to timer A4 interrupt requests Timer B0 to timer B5 interrupt requests UART0 transfer, UART0 reception interrupt requests UART1 transfer, UART1 reception interrupt requests UART2 transfer, UART2 reception interrupt requests SI/O3, SI/O4 interrpt requests A/D conversion interrupt requests Software triggers DMA0 > DMA1 (DMA0 takes precedence) 8 bits or 16 bits forward or fixed (The source and destination addresses cannot both be in the forward direction.) Transfer is completed when the DMAi transfer counter (i = 0-1) underflows after reaching the terminal count. When the DMAi transfer counter underflows, it is reloaded with the value of the DMAi transfer counter reload register and a DMA transfer is continued with it. When the DMAi transfer counter underflowed Data transfer is initiated each time a DMA request is generated when the DMAiCON register's DMAE bit = "1" (enabled). * When the DMAE bit is set to "0" (disabled) * After the DMAi transfer counter underflows When the DMAE bit is set to "0" (disabled) When a data transfer is started after setting the DMAE bit to "1" (enabled), the forward address pointer is reloaded with the value of the SARi or the DARi pointer whichever is specified to be in the forward direction and the DMAi transfer counter is reloaded with the value of the DMAi transfer counter reload register. Notes: 1. DMA transfer is not effective to any interrupt. DMA transfer is affected neither by the I flag nor by the interrupt control register. 2. The selectable causes of DMA requests differ with each channel. 3. Make sure that no DMAC-related registers (addresses 002016 to 003F16) are accessed by the DMAC. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 63 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 8. DMAC DMA0 request cause select register b7 b6 b5 b4 b3 b2 b1 b0 Symbol DM0SL Address 03B816 After reset 0016 Bit symbol DSEL0 DSEL1 DSEL2 DSEL3 (b5-b4) DMS Bit name DMA request cause select bit Refer to note Function RW RW RW RW RW Nothing is assigned. When write, set to "0". When read, its content is "0". DMA request cause expansion select bit Software DMA request bit 0: Basic cause of request 1: Extended cause of request t A DMA request is generated by setting this bit to "1" when the DMS bit is "0" (basic cause) and the DSEL3 to DSEL0 bits are "00012" (software trigger). The value of this bit when read is "0" . RW DSR RW Note 1: The causes of DMA0 requests can be selected by a combination of DMS bit and DSEL3 to DSEL0 bits in the manner described below. DSEL3 to DSEL0 0 0 0 02 0 0 0 12 0 0 1 02 0 0 1 12 0 1 0 02 0 1 0 12 0 1 1 02 0 1 1 12 1 0 0 02 1 0 0 12 1 0 1 02 1 0 1 12 1 1 0 02 1 1 0 12 1 1 1 02 1 1 1 12 DMS=0 (basic cause of request) Falling edge of INT0 pin Software trigger Timer A0 Timer A1 Timer A2 Timer A3 Timer A4 (Note 4) Timer B0 Timer B1 Timer B2 (Note 3) UART0 transmit UART0 receive UART2 transmit UART2 receive A-D conversion UART1 transmit DMS=1 (extended cause of request) - - - - - - Two edges of INT0 pin Timer B3 Timer B4 Timer B5 - - - - - - Note 2: In VINTi, INTRMTi, and HINTi (i = 0 to 3) of address 3616 expansion register of expansion function, when use them by the following setup, DMA request cause extension select bit = "1" (extended cause of request) cannot be used. * VINTi = 10112 * INTRMTi = 10102 * HINTi = 10012 (i = 0 to 3) Note 3: Please change SECINTi (i = 0 to 3) in address 3616 expansion registers of the expansion feature to the following settings when you use the DMA forwarding by timer B2 interrupt request. * SECINTi = 00002 The DMA forwarding by the clock timer interrupt request cannot be used. Note 4: Please change EXTIICINTi (i = 0 to 3) in address 02D616 I2C0 interrupt control register to the following settings when you use the DMA forwarding by timer A4 interrupt request. * EXTIICINTi = 00002 The DMA forwarding by the Multi-master I2C interrupt request cannot be used. Figure 8.2 DM0SL Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 64 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 8. DMAC DMA1 request cause select register b7 b6 b5 b4 b3 b2 b1 b0 Symbol DM1SL Address 03BA16 After reset 0016 Bit symbol Bit name DMA request cause select bit Refer to note Function RW RW RW RW RW DSEL0 DSEL1 DSEL2 DSEL3 (b5-b4) DMS Nothing is assigned. When write, set to "0". When read, its content is "0". DMA request cause expansion select bit Software DMA request bit 0: Basic cause of request 1: Extended cause of request A DMA request is generated by setting this bit to "1" when the DMS bit is "0" (basic cause) and the DSEL3 to DSEL0 bits are "00012" (software trigger). The value of this bit when read is "0" . RW DSR RW Note 1: The causes of DMA1 requests can be selected by a combination of DMS bit and DSEL3 to DSEL0 bits in the manner described below. DSEL3 to DSEL0 0 0 0 02 0 0 0 12 0 0 1 02 0 0 1 12 0 1 0 02 0 1 0 12 0 1 1 02 0 1 1 12 1 0 0 02 1 0 0 12 1 0 1 02 1 0 1 12 1 1 0 02 1 1 0 12 1 1 1 02 1 1 1 12 DMS=0(basic cause of request) Falling edge of INT1 pin Software trigger Timer A0 Timer A1 Timer A2 Timer A3 Timer A4 (Note 3) Timer B0 Timer B1 Timer B2 (Note 2) UART0 transmit UART0 receive/ACK0 UART2 transmit UART2 receive/ACK2 A/D conversion UART1 receive/ACK1 DMS=1(extended cause of request) - - - - - SI/O3 SI/O4 Two edges of INT1 - - - - - - - - Note 2: Please change SECINTi (i = 0 to 3) in address 3616 enhancing registers of the enhanced feature to the following settings when you use the DMA forwarding by timer B2 interrupt request. * SECINTi = 00002 The DMA forwarding by the clock timer interrupt request cannot be used. Note 3: Please change EXTIICINTi (i = 0 to 3) in address 02D616 I2C0 interrupt control register to the following settings when you use the DMA forwarding by timer A4 interrupt request. * EXTIICINTi = 00002 The DMA forwarding by the Multi-master I2C interrupt request cannot be used. DMAi control register (i = 0,1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol DM0CON DM1CON Bit symbol DMBIT DMASL DMAS DMAE DSD DAD (b7-b6) Address 002C16 003C16 Bit name Transfer unit bit select bit Repeat transfer mode select bit DMA request bit DMA enable bit Source address direction select bit (Note 2) After reset 00000X002 00000X002 Function 0 : 16 bits 1 : 8 bits 0 : Single transfer 1 : Repeat transfer 0 : DMA not requested 1 : DMA requested 0 : Disabled 1 : Enabled 0 : Fixed 1 : Forward RW RW RW RW (Note 1) RW RW RW Destination address 0 : Fixed direction select bit (Note 2) 1 : Forward Nothing is assigned. When write, set to "0". When read, its content is "0". Note 1: The DMAS bit can be set to "0" by writing "0" in a program (This bit remains unchanged even if "1" is written). Note 2: At least one of the DAD and DSD bits must be "0" (address direction fixed). Figure 8.3 DM1SL Register, DM0CON Register, and DM1CON Registers Page 65 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 8. DMAC DMAi source pointer (i = 0, 1) (Note) (b23) b7 (b19) b3 (b16)(b15) b0 b7 (b8) b0 b7 b0 Symbol SAR0 SAR1 Address 002216 to 002016 003216 to 003016 After reset Indeterminate Indeterminate Function Set the source address of transfer Setting range 0000016 to FFFFF16 RW RW Nothing is assigned. When write, set "0". When read, these contents are "0". Note: If the DSD bit of DMiCON register is "0" (fixed), this register can only be written to when the DMAE bit of DMiCON register is "0" (DMA disabled). If the DSD bit is "1" (forward direction), this register can be written to at any time. If the DSD bit is "1" and the DMAE bit is "1" (DMA enabled), the DMAi forward address pointer can be read from this register. Otherwise, the value written to it can be read. DMAi destination pointer (i = 0, 1)(Note) (b23) b7 (b19) b3 (b16)(b15) b0 b7 (b8) b0 b7 b0 Symbol DAR0 DAR1 Address 002616 to 002416 003616 to 003416 Setting range After reset Indeterminate Indeterminate RW RW Function Set the destination address of transfer 0000016 to FFFFF16 Nothing is assigned. When write, set "0". When read, these contents are "0". Note: If the DAD bit of DMiCON register is "0" (fixed), this register can only be written to when the DMAE bit of DMiCON register is "0"(DMA disabled). If the DAD bit is "1" (forward direction), this register can be written to at any time. If the DAD bit is "1" and the DMAE bit is "1" (DMA enabled), the DMAi forward address pointer can be read from this register. Otherwise, the value written to it can be read. DMAi transfer counter (i = 0, 1) (b15) b7 (b8) b0 b7 b0 Symbol TCR0 TCR1 Address 002916, 002816 003916, 003816 After reset Indeterminate Indeterminate RW Function Set the transfer count minus 1. The written value is stored in the DMAi transfer counter reload register, and when the DMAE bit of DMiCON register is set to "1" (DMA enabled) or the DMAi transfer counter underflows when the DMASL bit of DMiCON register is "1" (repeat transfer), the value of the DMAi transfer counter reload register is transferred to the DMAi transfer counter. When read, the DMAi transfer counter is read. Setting range 000016 to FFFF16 RW Figure 8.4 SAR0, SAR1, DAR0, DAR1, TCR0, and TCR1 Registers Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 66 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 8. DMAC 8.1 Transfer Cycles The transfer cycle consists of a memory or SFR read (source read) bus cycle and a write (destination write) bus cycle. The number of read and write bus cycles is affected by the source and destination addresses of transfer. (a) Effect of Source and Destination Addresses If the transfer unit and data bus both are 16 bits and the source address of transfer begins with an odd address, the source read cycle consists of one more bus cycle than when the source address of transfer begins with an even address. Similarly, if the transfer unit and data bus both are 16 bits and the destination address of transfer begins with an odd address, the destination write cycle consists of one more bus cycle than when the destination address of transfer begins with an even address. (b) Effect of Software Wait For memory or SFR accesses in which one or more software wait states are inserted, the number of bus cycles required for that access increases by an amount equal to software wait states. Figure 8.5 shows the example of the cycles for a source read. For convenience, the destination write cycle is shown as one cycle and the source read cycles for the different conditions are shown. In reality, the destination write cycle is subject to the same conditions as the source read cycle, with the transfer cycle changing accordingly. When calculating transfer cycles, take into consideration each condition for the source read and the destination write cycle, respectively. For example, when data is transferred in 16 bit units using an 8-bit bus ((2) in Figure 8.5), two source read bus cycles and two destination write bus cycles are required. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 67 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 8. DMAC (1) When the transfer unit is 8 or 16 bits and the source of transfer is an even address BCLK Address bus RD signal WR signal Data bus CPU use Source Destination Dummy cycle CPU use CPU use Source Destination Dummy cycle CPU use (2) When the transfer unit is 16 bits and the source address of transfer is an odd address, or when the transfer unit is 16 bits and an 8-bit bus is used BCLK Address bus RD signal WR signal Data bus CPU use Source Source + 1 Destination Dummy cycle CPU use CPU use Source Source + 1 Destination Dummy cycle CPU use (3) When the source read cycle under condition (1) has one wait state inserted BCLK Address bus RD signal WR signal Data bus CPU use Source Destination Dummy cycle CPU use CPU use Source Destination Dummy cycle CPU use (4) When the source read cycle under condition (2) has one wait state inserted BCLK Address bus RD signal WR signal Data bus CPU use Source Source + 1 Destination Dummy cycle CPU use CPU use Source Source + 1 Destination Dummy cycle CPU use Note: The same timing changes occur with the respective conditions at the destination as at the source . Figure 8.5 Transfer Cycles for Source Read Page 68 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 8. DMAC 8.2 Number of DMA Transfer Cycles Any combination of even or odd transfer read and write addresses is possible. Table 8.2 shows the number of DMA transfer cycles. Table 8.3 shows the Coefficient j, k. The number of DMAC transfer cycles can be calculated as follows: No. of transfer cycles per transfer unit = No. of read cycles x j + No. of write cycles x k Table 8.2 Number of DMA Transfer Cycles Single-chip mode Transfer unit Bus width Access address No. of read No. of write cycles cycles 1 1 1 2 1 1 1 2 8-bit transfers (DMBIT= "1") 16-bit transfers (DMBIT= "0") 16-bit (BYTE= "L") 16-bit (BYTE = "L") Even Odd Even Odd Table 8.3 Coefficient j, k Internal area Internal ROM, RAM No wait j k 1 1 With wait 2 2 2 2 SFR Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 69 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 8. DMAC 8.3 DMA Enable When a data transfer starts after setting the DMAE bit in DMiCON register (i = 0, 1) to "1" (enabled), the DMAC operates as follows: (1) Reload the forward address pointer with the SARi register value when the DSD bit in DMiCON register is "1" (forward) or the DARi register value when the DAD bit of DMiCON register is "1" (forward). (2) Reload the DMAi transfer counter with the DMAi transfer counter reload register value. If the DMAE bit is set to "1" again while it remains set, the DMAC performs the above operation. However, if a DMA request may occur simultaneously when the DMAE bit is being written, follow the steps below. Step 1: Write "1" to the DMAE bit and DMAS bit in DMiCON register simultaneously. Step 2: Make sure that the DMAi is in an initial state as described above (1) and (2) in a program. If the DMAi is not in an initial state, the above steps should be repeated. 8.4 DMA Request The DMAC can generate a DMA request as triggered by the cause of request that is selected with the DMS and DSEL3 to DSEL0 bits of DMiSL register (i = 0, 1) on either channel. Table 8.4 shows the timing at which the DMAS bit changes state. Whenever a DMA request is generated, the DMAS bit is set to "1" (DMA requested) regardless of whether or not the DMAE bit is set. If the DMAE bit was set to "1" (enabled) when this occurred, the DMAS bit is set to "0" (DMA not requested) immediately before a data transfer starts. This bit cannot be set to "1" in a program (it can only be set to "0"). The DMAS bit may be set to "1" when the DMS or the DSEL3 to DSEL0 bits change state. Therefore, always be sure to set the DMAS bit to "0" after changing the DMS or the DSEL3 to DSEL0 bits. Because if the DMAE bit is "1", a data transfer starts immediately after a DMA request is generated, the DMAS bit in almost all cases is "0" when read in a program. Read the DMAE bit to determine whether the DMAC is enabled. Table 8.4 Timing at Which the DMAS Bit Changes State DMA factor Software trigger Peripheral function DMAS bit of the DMiCON register Timing at which the bit is set to "1" Timing at which the bit is set to "0" When the DSR bit of DMiSL register is set to "1" When the interrupt control register for the peripheral function that is selected by the DSEL3 to DSEL0 and DMS bits of DMiSL register has its IR bit set to "1" * Immediately before a data transfer starts * When set by writing "0" in a program Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 70 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 8. DMAC 8.5 Channel Priority and DMA Transfer Timing If both DMA0 and DMA1 are enabled and DMA transfer request signals from DMA0 and DMA1 are detected active in the same sampling period (one period from a falling edge to the next falling edge of BCLK), the DMAS bit on each channel is set to "1" (DMA requested) at the same time. In this case, the DMA requests are arbitrated according to the channel priority, DMA0 > DMA1. The following describes DMAC operation when DMA0 and DMA1 requests are detected active in the same sampling period. Figure 8.6 shows an example of DMA transfer effected by external factors. DMA0 request having priority is received first to start a transfer when a DMA0 request and DMA1 request are generated simultaneously. After one DMA0 transfer is completed, a bus arbitration is returned to the CPU. When the CPU has completed one bus access, a DMA1 transfer starts. After one DMA1 transfer is completed, the bus arbitration is again returned to the CPU. In addition, DMA requests cannot be counted up since each channel has one DMAS bit. Therefore, when DMA requests, as DMA1 in Figure 8.6, occurs more than one time, the DMAS bit is set to "0" as soon as getting the bus arbitration. The bus arbitration is returned to the CPU when one transfer is completed. An example where DMA requests for external causes are detected active at the same BCLK DMA0 DMA1 CPU INT0 DMA0 request bit INT1 DMA1 request bit Bus arbitration Figure 8.6 DMA Transfer by External Factors Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 71 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 9. Timers Eleven 16-bit timers, each capable of operating independently of the others, can be classified by function as either timer A (five) and timer B (six). The count source for each timer acts as a clock, to control such timer operations as counting, reloading, etc. Figures 9.1 and 9.2 show block diagrams of timer A and timer B configuration, respectively. 1/2 * Main clock f1 f2 PCLK0 bit = 0 f1 or f2 PCLK0 bit = 1 XCIN f8 1/4 f32 Clock prescaler 1/32 Reset fC32 1/8 f1 or f2 f8 f32 fC32 Set the CPSR bit of CPSRF register to "1" (= prescaler reset) * Timer mode * One-shot timer mode * Pulse Width Modulation (PWM) mode Timer A0 interrupt TA0IN Noise filter Timer A0 * Event counter mode * Timer mode * One-shot timer mode * PWM mode Timer A1 interrupt TA1IN Noise filter Timer A1 * Event counter mode * Timer mode * One-shot timer mode * PWM mode Timer A2 interrupt TA2IN Noise filter Timer A2 * Event counter mode * Timer mode * One-shot timer mode * PWM mode Timer A3 interrupt TA3IN Noise filter Timer A3 * Event counter mode * Timer mode * One-shot timer mode * PWM mode Timer A4 interrupt TA4IN Noise filter Timer A4 * Event counter mode Timer B2 overflow or underflow Note: Be aware that TA0IN shares the pin with RxD2 and TB5IN. Figure 9.1 Timer A Configuration Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 72 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 1/2 * Main clock f1 f2 PCLK0 bit = 0 f1 or f2 PCLK0 bit = 1 XCIN f8 1/4 f32 Clock prescaler 1/32 Reset fC32 1/8 Set the CPSR bit of CPSRF register to "1" (= prescaler reset) f1 or f2 f8 f32 fC32 Timer B2 overflow or underflow ( to Timer A count source) * Timer mode * Pulse width measuring mode, pulse period measuring mode TB0IN Noise filter Timer B0 interrupt Timer B0 * Event counter mode * Timer mode * Pulse width measuring mode, pulse period measuring mode TB1IN Noise filter Timer B1 interrupt Timer B1 * Event counter mode * Timer mode * Pulse width measuring mode, pulse period measuring mode Timer B2 interrupt TB2IN Noise filter Timer B2 * Event counter mode * Timer mode * Pulse width measuring mode, pulse period measuring mode Timer B3 interrupt TB3IN Noise filter Timer B3 * Event counter mode * Timer mode * Pulse width measuring mode, pulse period measuring mode Timer B4 interrupt TB4IN Noise filter Timer B4 * Event counter mode * Timer mode * Pulse width measuring mode, pulse period measuring mode Timer B5 interrupt TB5IN Noise filter Timer B5 * Event counter mode Note: Be aware that TB5IN shares the pin with RxD2 and TA0IN. Figure 9.2 Timer B Configuration Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 73 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 9.1 Timer A Figure 9.3 shows a block diagram of the timer A. Figures 9.4 to 9.6 show registers related to the timer A. The timer A supports the following four modes. Except in event counter mode, timers A0 to A4 all have the same function. Use the TMOD1 to TMOD0 bits of TAiMR register (i = 0 to 4) to select the desired mode. * Timer mode: The timer counts an internal count source. * Event counter mode: The timer counts pulses from an external device or overflows and underflows of other timers. * One-shot timer mode: The timer outputs a pulse only once before it reaches the minimum count "000016." * Pulse width modulation (PWM) mode: The timer outputs pulses in a given width successively. Data bus high-order bits Clock source selection f1 or f2 f8 f32 fC32 Polarity selection TAiIN (i = 0 to 4) * Timer * One shot * PWM * Timer (gate function) * Event counter Clock selection Data bus low-order bits Low-order 8 bits Reload register High-order 8 bits Counter Up-count/down-count Always counts down except in event counter mode TAi Timer A0 Timer A1 Timer A2 Timer A3 Timer A4 Addresses 038716 038616 038916 038816 038B16 038A16 038D16 038C16 038F16 038E16 TAj Timer A4 Timer A0 Timer A1 Timer A2 Timer A3 TAk Timer A1 Timer A2 Timer A3 Timer A4 Timer A0 Clock selection (Note) (Note) To external trigger circuit TABSR register TB2 overflow TAj overflow (j = i - 1. Note, however, that j = 4 when i = 0) Down count TAk overflow (k = i + 1. Note, however, that k = 0 when i = 4) UDF register TAiOUT (i = 0 to 4) Pulse output Toggle flip-flop Note: Overflow or underflow Figure 9.3 Timer A Block Diagram Timer Ai mode register (i=0 to 4) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TA0MR to TA4MR Address 039616 to 039A16 After reset 0016 Bit symbol TMOD0 Bit name Operation mode select bit b1 b0 Function 0 0 : Timer mode 0 1 : Event counter mode 1 0 : One-shot timer mode 1 1 : Pulse width modulation (PWM) mode RW RW RW RW RW RW RW RW RW TMOD1 MR0 MR1 MR2 MR3 TCK0 TCK1 Function varies with each operation mode Count source select bit Function varies with each operation mode Figure 9.4 TA0MR to TA4MR Registers Page 74 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS Timer Ai register (i= 0 to 4) (Note 1) (b15) b7 (b8) b0 b7 b0 Symbol TA0 TA1 TA2 TA3 TA4 Function Address 038716, 038616 038916, 038816 038B16, 038A16 038D16, 038C16 038F16, 038E16 After reset Indeterminate Indeterminate Indeterminate Indeterminate Indeterminate Setting range 000016 to FFFF16 000016 to FFFF16 RW RW RW WO Mode Timer mode Event counter mode One-shot timer mode Divide the count source by n + 1 where n = set value Divide the count source by FFFF16 - n + 1 where n = set value when counting up or by n + 1 when counting down (Note 5) Divide the count source by n where n = set value and cause the timer to stop 000016 to FFFF16 (Notes 2, 4) Pulse width Modify the pulse width as follows: modulation PWM period: (216 - 1) / fj High level PWM pulse width: n / fj mode (16-bit PWM) where n = set value, fj = count source frequency Pulse width Modify the pulse width as follows: modulation PWM period: (28 - 1) x (m + 1)/ fj mode High level PWM pulse width: (m + 1)n / fj (8-bit PWM) where n = high-order address set value, m = low-order address set value, fj = count source frequency 000016 to FFFE16 (Note 3, 4) WO 0016 to FE16 (High-order address) 0016 to FF16 (Low-order address) WO (Note 3, 4) Note 1: The register must be accessed in 16 bit units. Note 2: If the TAi register is set to `000016,' the counter does not work and timer Ai interrupt requests are not generated either. Furthermore, if "pulse output" is selected, no pulses are output from the TAiOUT pin. Note 3: If the TAi register is set to `000016,' the pulse width modulator does not work, the output level on the TAiOUT pin remains low, and timer Ai interrupt requests are not generated either. The same applies when the 8 high-order bits of the timer TAi register are set to `001 6' while operating as an 8-bit pulse width modulator. Note 4: Use the MOV instruction to write to the TAi register. Note 5: The timer counts pulses from an external device or overflows or underflows in other timers. Count start flag b7 b6 b5 b4 b3 b2 b1 b0 Symbol TABSR Address 038016 After reset 0016 Bit symbol TA0S TA1S TA2S TA3S TA4S TB0S TB1S TB2S Bit name Timer A0 count start flag Timer A1 count start flag Timer A2 count start flag Timer A3 count start flag Timer A4 count start flag Timer B0 count start flag Timer B1 count start flag Timer B2 count start flag Function 0 : Stops counting 1 : Starts counting RW RW RW RW RW RW RW RW RW Up/down flag (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol UDF Address 038416 After reset 0016 Bit symbol TA0UD TA1UD TA2UD TA3UD TA4UD TA2P TA3P TA4P Bit name Timer A0 up/down flag Timer A1 up/down flag Timer A2 up/down flag Timer A3 up/down flag Timer A4 up/down flag Function 0 : Down count 1 : Up count Enabled by setting the TAiMR register's MR2 bit to "0" (= switching source in UDF register) during event counter mode. RW RW RW RW RW RW Timer A2 two-phase pulse 0 : two-phase pulse signal WO processing disabled signal processing select bit 1 : two-phase pulse signal processing enabled Timer A3 two-phase pulse WO (Notes 2, 3) signal processing select bit Timer A4 two-phase pulse signal processing select bit WO Note 1: Use MOV instruction to write to this register. Note 2: Make sure the port direction bits for the TA2IN to TA4IN and TA2OUT to TA4OUT pins are set to "0" (input mode). Note 3: When not using the two-phase pulse signal processing function, set the bit corresponding to timer . to timer A4 to "0" A2 Figure 9.5 TA0 to TA4 Registers, TABSR Register, and UDF Register Page 75 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS One-shot start flag b7 b6 b5 b4 b3 b2 b1 b0 Symbol ONSF Address 038216 After reset 0016 0 Bit symbol TA0OS TA1OS TA2OS TA3OS TA4OS (b5) TA0TGL TA0TGH Bit name Timer A0 one-shot start flag Timer A1 one-shot start flag Timer A2 one-shot start flag Timer A3 one-shot start flag Timer A4 one-shot start flag Reserved bit Timer A0 event/trigger select bit Function The timer starts counting by setting this bit to "1" while the TMOD1 to TMOD0 bits of TAiMR register (i = 0 to 4) = `102' (= one-shot timer mode) and the MR2 bit of TAiMR register = "0" (=TAiOS bit enabled). When read, its content is "0". Must be set to "0" b7 b6 RW RW RW RW RW RW RW RW 0 0 : Input on TA0IN is selected (Note 1) (Note 2) 0 1 : TB2 overflow is selected 1 0 : TA4 overflow is selected (Note 2) RW 1 1 : TA1 overflow is selected (Note 2) Note 1: Make sure the PD7_1 bit of PD7 register is set to "0" (= input mode). Note 2: Overflow or underflow Trigger select register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRGSR Address 038316 After reset 0016 Bit symbol TA1TGL Bit name Timer A1 event/trigger select bit Function b1 b0 RW RW RW RW RW RW RW RW RW TA1TGH TA2TGL 0 0 : Input on TA1IN is selected (Note 1) 0 1 : TB2 is selected 1 0 : TA0 is selected 1 1 : TA2 is selected b3 b2 Timer A2 event/trigger select bit TA2TGH TA3TGL TA3TGH 0 0 : Input on TA2IN is selected (Note 1) 0 1 : TB2 is selected 1 0 : TA1 is selected 1 1 : TA3 is selected b5 b4 Timer A3 event/trigger select bit 0 0 : Input on TA3IN is selected (Note 1) 0 1 : TB2 is selected 1 0 : TA2 is selected 1 1 : TA4 is selected b7 b6 TA4TGL TA4TGH Timer A4 event/trigger select bit 0 0 : Input on TA4IN is selected (Note 1) 0 1 : TB2 is selected 1 0 : TA3 is selected 1 1 : TA0 is selected Note 1: Make sure the port direction bits for the TA1IN to TA4IN pins are set to "0" (= input mode). Clock prescaler reset flag b7 b6 b5 b4 b3 b2 b1 b0 Symbol CPSRF Address 038116 After reset 0XXXXXXX2 RW Bit symbol (b6-b0) CPSR Bit name Function Nothing is assigned. When write, set to "0". When read, their contents are indeterminate. Clock prescaler reset flag Setting this bit to "1" initializes the prescaler for the timekeeping clock. (When read, its content is "0".) RW Figure 9.6 ONSF Register, TRGSR Register, and CPSRF Register Page 76 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 9.1.1 Timer Mode In timer mode, the timer counts a count source generated internally (see Table 9.1). Figure 9.7 shows TAiMR register in timer mode. Table 9.1 Specifications in Timer Mode Item Count source Count operation Divide ratio Count start condition Count stop condition Interrupt request generation timing TAiIN pin function TAiOUT pin function Read from timer Write to timer Specification f1, f2, f8, f32, fC32 * Down-count * When the timer underflows, it reloads the reload register contents and continues counting 1/(n+1) n: set value of TAi register (i= 0 to 4) 000016 to FFFF16 Set TAiS bit of TABSR register to "1" (= start counting) Set TAiS bit to "0" (= stop counting) Timer underflow I/O port or gate input I/O port or pulse output Count value can be read by reading TAi register * When not counting and until the 1st count source is input after counting start Value written to TAi register is written to both reload register and counter * When counting (after 1st count source input) Value written to TAi register is written to only reload register (Transferred to counter when reloaded next) * Gate function Counting can be started and stopped by an input signal to TAiIN pin * Pulse output function Whenever the timer underflows, the output polarity of TAiOUT pin is inverted. When not counting, the pin outputs a low. Select function Timer Ai mode register (i=0 to 4) b7 b6 b5 b4 b3 b2 b1 b0 0 00 Symbol TA0MR to TA4MR Bit symbol TMOD0 TMOD1 MR0 Address 039616 to 039A16 Bit name After reset 0016 Function RW RW RW RW Operation mode select bit Pulse output function select bit b1 b0 0 0 : Timer mode 0 : Pulse is not output (TAiOUT pin is a normal port pin) 1 : Pulse is output (Note 1) (TAiOUT pin is a pulse output pin) b4 b3 MR1 Gate function select bit MR2 0 0 : Gate function not available 01: (TAiIN pin functions as I/O port) 1 0 : Counts while input on the TAiIN pin is low (Note 2) 1 1 : Counts while input on the TAiIN pin is high (Note 2) RW RW RW RW RW MR3 TCK0 TCK1 Must be set to "0" in timer mode Count source select bit b7 b6 0 0 : f1 or f2 0 1 : f8 1 0 : f32 1 1 : fC32 Note 1: TA0OUT pin is N-channel open drain output. Note 2: The port direction bit for the TAiIN pin must be set to "0" (= input mode). Figure 9.7 Timer Ai Mode Register in Timer Mode Page 77 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 9.1.2 Event Counter Mode In event counter mode, the timer counts pulses from an external device or overflows and underflows of other timers. Timers A2, A3 and A4 can count two-phase external signals. Table 9.2 lists specifications in event counter mode (when not processing two-phase pulse signal). Table 9.3 lists specifications in event counter mode (when processing two-phase pulse signal with the timers A2, A3 and A4). Figure 9.8 shows TAiMR register in event counter mode (when not processing two-phase pulse signal). Figure 9.9 shows TA2MR to TA4MR registers in event counter mode (when processing two-phase pulse signal with the timers A2, A3 and A4). Table 9.2 Specifications in Event Counter Mode (when not processing two-phase pulse signal) Specification * External signals input to TAiIN pin (i=0 to 4) (effective edge can be selected in program) * Timer B2 overflows or underflows, timer Aj (j=i-1, except j=4 if i=0) overflows or underflows, timer Ak (k=i+1, except k=0 if i=4) overflows or underflows Count operation * Up-count or down-count can be selected by external signal or program * When the timer overflows or underflows, it reloads the reload register contents and continues counting. When operating in free-running mode, the timer continues counting without reloading. Divided ratio 1/ (FFFF16 - n + 1) for up-count 1/ (n + 1) for down-count n : set value of TAi register 000016 to FFFF16 Count start condition Set TAiS bit of TABSR register to "1" (= start counting) Count stop condition Set TAiS bit to "0" (= stop counting) Interrupt request generation timing Timer overflow or underflow TAiIN pin function I/O port or count source input TAiOUT pin function I/O port, pulse output, or up/down-count select input Read from timer Count value can be read by reading TAi register * When not counting and until the 1st count source is input after counting start Write to timer Value written to TAi register is written to both reload register and counter * When counting (after 1st count source input) Value written to TAi register is written to only reload register (Transferred to counter when reloaded next) Select function * Free-run count function Even when the timer overflows or underflows, the reload register content is not reloaded to it * Pulse output function Whenever the timer overflows or underflows, the output polarity of TAiOUT pin is inverted . When not counting, the pin outputs a low. Item Count source Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 78 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS Timer Ai mode register (i=0 to 4) (When not using two-phase pulse signal processing) b7 b6 b5 b4 b3 b2 b1 b0 0 01 Symbol TA0MR to TA4MR Bit symbol TMOD0 TMOD1 MR0 Bit name Address 039616 to 039A16 After reset 0016 Function RW RW RW RW RW Operation mode select bit Pulse output function select bit b1 b0 0 1 : Event counter mode (Note 1) 0 : Pulse is not output (TAiOUT pin functions as I/O port) 1 : Pulse is output (Note 2) (TAiOUT pin functions as pulse output pin) MR1 MR2 MR3 TCK0 TCK1 Count polarity select bit (Note 3) Up/down switching cause select bit 0 : Counts external signal's falling edge RW 1 : Counts external signal's rising edge 0 : UDF register 1 : Input signal to TAiOUT pin (Note 4) RW RW RW RW Must be set to "0" in event counter mode Count operation type select bit 0 : Reload type 1 : Free-run type Can be "0" or "1" when not using two-phase pulse signal processing Note 1: During event counter mode, the count source can be selected using the ONSF and TRGSR registers. Note 2: TA0OUT pin is N-channel open drain output. Note 3: Effective when the TAiGH and TAiGL bits of ONSF or TRGSR register are `002' (TAiIN pin input). Note 4: Count down when input on TAiOUT pin is low or count up when input on that pin is high. The port direction bit for TAiOUT pin must be set to "0" (= input mode). Figure 9.8 TAiMR Register in Event Counter Mode (when not using two-phase pulse signal processing) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 79 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS The use of the event counter mode (When you use two aspect pulse signal processing with Timer A2, A3, and A4) is shown in Table 9.3. Figure 9.9 shows from TA2MR register to TA4MR register (When you use two aspect pulse signal processing with timer A2, A3, and A4) at event counter mode. Table 9.3 Item Count source Count operation Specifications in Event Counter Mode (when processing two-phase pulse signal with timers A2, A3 and A4)) Specification * Two-phase pulse signals input to TAiIN or TAiOUT pins (i = 2 to 4) * Up-count or down-count can be selected by two-phase pulse signal * When the timer overflows or underflows, it reloads the reload register contents and continues counting. When operating in free-running mode, the timer continues counting without reloading. 1/ (FFFF16 - n + 1) for up-count 1/ (n + 1) for down-count n : set value of TAi register 000016 to FFFF16 Set TAiS bit of TABSR register to "1" (= start counting) Set TAiS bit to "0" (= stop counting) Timer overflow or underflow Two-phase pulse input Two-phase pulse input Count value can be read by reading timer A2, A3 or A4 register * When not counting and until the 1st count source is input after counting start Value written to TAi register is written to both reload register and counter * When counting (after 1st count source input) Value written to TAi register is written to reload register (Transferred to counter when reloaded next) * Normal processing operation (timer A2 and timer A3) The timer counts up rising edges or counts down falling edges on TAjIN pin when input signals on TAj OUT pin is "H". TAjOUT TAjIN (j=2,3) Divide ratio Count start condition Count stop condition Interrupt request generation timing TAiIN pin function TAiOUT pin function Read from timer Write to timer Select function (Note) Upcount Upcount Upcount Downcount Downcount Downcount * Multiply-by-4 processing operation (timer A3 and timer A4) If the phase relationship is such that TAkIN(k=3, 4) pin goes "H" when the input signal on TAkOUT pin is "H", the timer counts up rising and falling edges on TAkOUT and TAkIN pins. If the phase relationship is such that TAkIN pin goes "L" when the input signal on TAkOUT pin is "H", the timer counts down rising and falling edges on TAkOUT and TAkIN pins. TAkOUT Count up all edges Count down all edges TAkIN (k=3,4) Count up all edges Count down all edges Notes: 1. Only timer A3 is selectable. Timer A2 is fixed to normal processing operation, and timer A4 is fixed to multiply-by-4 processing operation. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 80 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS Timer Ai mode register (i=2 to 4) (When using two-phase pulse signal processing) b6 b5 b4 b3 b2 b1 b0 010001 Symbol TA2MR to TA4MR Address 039816 to 039A16 After reset 0016 Bit name TMOD0 TMOD1 MR0 MR1 MR2 MR3 TCK0 TCK1 Operation mode select bit b1 b0 Function 0 1 : Event counter mode RW RW RW RW RW RW RW RW RW To use two-phase pulse signal processing, set this bit to "0". To use two-phase pulse signal processing, set this bit to "0". To use two-phase pulse signal processing, set this bit to "1". To use two-phase pulse signal processing, set this bit to "0". Count operation type select bit Two-phase pulse signal processing operation select bit (Note 1)(Note 2) 0 : Reload type 1 : Free-run type 0 : Normal processing operation 1 : Multiply-by-4 processing operation Note 1: TCK1 bit is valid for timer A3 mode register. No matter how this bit is set, timers A2 and A4 always operate in normal processing mode and x4 processing mode, respectively. Note 2: If two-phase pulse signal processing is desired, following register settings are required: * Set the UDF register's TAiP bit to "1" (two-phase pulse signal processing function enabled) . * Set the TRGSR register's TAiGH and TAiGL bits to "002" (TAiIN pin input). * Set the port direction bits for TA iIN and TAiOUT to "0" (input mode). Figure 9.9 TA2MR to TA4MR Registers in Event Counter Mode (when using two-phase pulsesignal processing with timer A2, A3 or A4) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 81 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 9.1.3 One-shot Timer Mode In one-shot timer mode, the timer is activated only once by one trigger. (See Table 9.4.) When the trigger occurs, the timer starts up and continues operating for a given period. Figure 9.10 shows the TAiMR register in one-shot timer mode. Table 9.4 Specifications in One-shot Timer Mode Specification f1, f2, f8, f32, fC32 * Down-count * When the counter reaches 000016, it stops counting after reloading a new value * If a trigger occurs when counting, the timer reloads a new count and restarts counting 1/n n : set value of TAi register 000016 to FFFF16 However, the counter does not work if the divide-by-n value is set to 000016. TAiS bit of TABSR register = "1" (start counting) and one of the following triggers occurs. * External trigger input from the TAiIN pin * Timer B2 overflow or underflow, timer Aj (j=i-1, except j=4 if i=0) overflow or underflow, timer Ak (k=i+1, except k=0 if i=4) overflow or underflow * The TAiOS bit of ONSF register is set to "1" (= timer starts) * When the counter is reloaded after reaching "000016" * TAiS bit is set to "0" (= stop counting) When the counter reaches "000016" I/O port or trigger input I/O port or pulse output An indeterminate value is read by reading TAi register * When not counting and until the 1st count source is input after counting start Value written to TAi register is written to both reload register and counter * When counting (after 1st count source input) Value written to TAi register is written to only reload register (Transferred to counter when reloaded next) * Pulse output function The timer outputs a low when not counting and a high when counting. Item Count source Count operation Divide ratio Count start condition Count stop condition Interrupt request generation timing TAiIN pin function TAiOUT pin function Read from timer Write to timer Select function Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 82 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS Timer Ai mode register (i=0 to 4) b7 b6 b5 b4 b3 b2 b1 b0 0 10 Symbol TA0MR to TA4MR Bit symbol TMOD0 TMOD1 MR0 Address 039616 to 039A16 After reset 0016 Function RW RW RW Bit name Operation mode select bit Pulse output function select bit b1 b0 1 0 : One-shot timer mode 0 : Pulse is not output (TAiOUT pin functions as I/O port) RW 1 : Pulse is output (Note 1) (TAiOUT pin functions as a pulse output pin) 0 : Falling edge of input signal to TAiIN pin (Note 3) 1 : Rising edge of input signal to TAiIN pin (Note 3) RW MR1 MR2 External trigger select bit (Note 2) Trigger select bit 0 : TAiOS bit is enabled 1 : Selected by TAiTGH to TAiTGL bits RW RW RW RW MR3 TCK0 TCK1 Must be set to "0" in one-shot timer mode Count source select bit b7 b6 0 0 : f1 or f2 0 1 : f8 1 0 : f32 1 1 : fC32 Note 1: TA0OUT pin is N-channel open drain output. Note 2: Effective when the TAiTGH and TAiTGL bits of ONSF or TRGSR register are `002' (TAiIN pin input). Note 3: The port direction bit for the TAiIN pin must be set to "0" (= input mode). Figure 9.10 TAiMR Register in One-shot Timer Mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 83 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 9.1.4 Pulse Width Modulation (PWM) Mode In PWM mode, the timer outputs pulses of a given width in succession (see Table 9.5). The counter functions as either 16-bit pulse width modulator or 8-bit pulse width modulator. Figure 9.11 shows TAiMR register in pulse width modulation mode. Figures 9.12 and 9.13 show examples of how a 16-bit pulse width modulator operates and how an 8-bit pulse width modulator operates. Table 9.5 Specifications in PWM Mode Item Count source Count operation Specification f1, f2, f8, f32, fC32 * Down-count (operating as an 8-bit or a 16-bit pulse width modulator) * The timer reloads a new value at a rising edge of PWM pulse and continues counting * The timer is not affected by a trigger that occurs during counting * High level width n / fj n : set value of TAi register (i=o to 4) * Cycle time (216-1) / fj fixed fj: count source frequency (f1, f2, f8, f32, fC32) * High level width n x (m+1) / fj n : set value of TAi register high-order address * Cycle time (28-1) x (m+1) / fj m : set value of TAi register low-order address * TAiS bit of TABSR register is set to "1" (= start counting) * The TAiS bit = 1 and external trigger input from the TAiIN pin * The TAiS bit = 1 and one of the following external triggers occurs * Timer B2 overflow or underflow, timer Aj (j=i-1, except j=4 if i=0) overflow or underflow, timer Ak (k=i+1, except k=0 if i=4) overflow or underflow TAiS bit is set to "0" (= stop counting) PWM pulse goes "L" I/O port or trigger input Pulse output An indeterminate value is read by reading TAi register * When not counting and until the 1st count source is input after counting start Value written to TAi register is written to both reload register and counter * When counting (after 1st count source input) Value written to TAi register is written to only reload register (Transferred to counter when reloaded next) 16-bit PWM 8-bit PWM Count start condition Count stop condition Interrupt request generation timing TAiIN pin function TAiOUT pin function Read from timer Write to timer Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 84 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS Timer Ai mode register (i= 0 to 4) b7 b6 b5 b4 b3 b2 b1 b0 111 Symbol TA0MR to TA4MR Bit symbol TMOD0 TMOD1 MR0 MR1 MR2 Address 039616 to 039A16 After reset 0016 Function RW RW (Note 1) RW RW Bit name Operation mode select bit b1 b0 1 1 : PWM mode Must be set to "1" in PWM mode External trigger select bit (Note 2) Trigger select bit 0: Falling edge of input signal to TAiIN pin(Note 3) RW 1: Rising edge of input signal to TAiIN pin(Note 3) 0 : Write "1" to TAiS bit in the TABSR register 1 : Selected by TAiTGH to TAiTGL bits 0: Functions as a 16-bit pulse width modulator 1: Functions as an 8-bit pulse width modulator b7 b6 RW MR3 16/8-bit PWM mode select bit Count source select bit RW RW RW TCK0 TCK1 0 0 : f1 or f2 0 1 : f8 1 0 : f32 1 1 : fC32 Note 1: TA0OUT pin is N-channel open drain output. Note 2: Effective when the TAiTGH and TAiTGL bits of ONSF or TRGSR register are "00"2 (TAi IN pin input). Note 3: The port direction bit for the TAiIN pin must be set to "0" (= input mode). Figure 9.11 TAiMR Register in PWM Mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 85 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 1 / fi X (2 16 - 1) Count source Input signal to TAiIN pin "H" "L" Trigger is not generated by this signal 1 / fj X n PWM pulse output from TAiOUT pin IR bit of TAiIC register "H" "L" "1" "0" fj : Frequency of count source (f1, f2, f8, f32, fC32) Set to "0" upon accepting an interrupt request or by writing in program i = 0 to 4 Note 1: n = 000016 to FFFE16. Note 2: This timing diagram is for the case where the TAi register is `000316,' the TAiTGH and TAiTGL bits of ONSF or TRGSR register = `002' (TAiIN pin input), the MR1 bit of TAiMR register = 1 (rising edge), and the MR2 bit of TAiMR register = 1 (trigger selected by TAiTGH and TAiTGL bits). Figure 9.12 Example of 16-bit Pulse Width Modulator Operation 1 / fj X (m+ 1) X (2 8 - 1) Count source (Note1) Input signal to TAiIN pin "H" "L" 1 / fj X (m + 1) "H" Underflow signal of 8-bit prescaler (Note2) "L" 1 / fj X (m + 1) X n PWM pulse output from TAiOUT pin "H" "L" "1" "0" IR bit of TAiIC register fj : Frequency of count source (f1, f2, f8, f32, fC32) i = 0 to 4 Set to "0" upon accepting an interrupt request or by writing in program Note 1: The 8-bit prescaler counts the count source. Note 2: The 8-bit pulse width modulator counts the 8-bit prescaler's underflow signal. Note 3: m = 0016 to FF16; n = 0016 to FE16. Note 4: This timing diagram is for the case where the TAi register is `020216,' the TAiTGH and TAiTGL bits of ONSF or TRGSR register = `002' (TAiIN pin input), the MR1 bit of TAiMR register = 0 (falling edge), and the MR2 bit of TAiMR register = 1 (trigger selected by TAiTGH and TAiTGL bits). Figure 9.13 Example of 8-bit Pulse Width Modulator Operation Page 86 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 9.2 Timer B Figure 9.14 shows a block diagram of the timer B. Figures 9.15 and 9.16 show registers related to the timer B. Timer B supports the following three modes. Use the TMOD1 and TMOD0 bits of TBiMR register (i = 0 to 5) to select the desired mode. * Timer mode: The timer counts an internal count source. * Event counter mode: The timer counts pulses from an external device or overflows or underflows of other timers. * Pulse period/pulse width measuring mode: The timer measures an external signal's pulse period or pulse width. Data bus high-order bits Data bus low-order bits Clock source selection f1 or f2 f8 f32 fC32 TBiIN (i = 0 to 5) * Timer * Pulse period measurement, pulse width measurement Low-order 8 bits High-order 8 bits Reload register Clock selection * Event counter Polarity switching, edge pulse TABSR register TBSR register Counter reset circuit Can be selected in only event counter mode TBj overflow (Note) (j = i - 1. Note, however, j = 2 when i = 0, j = 5 when i = 3) TBi Timer B0 Timer B1 Timer B2 Timer B3 Timer B4 Timer B5 Address 039116 039016 039316 039216 039516 039416 035116 035016 035316 035216 035516 035416 TBj Timer B2 Timer B0 Timer B1 Timer B5 Timer B3 Timer B4 Counter Note: Overflow or underflow. Figure 9.14 Timer B Block Diagram Timer Bi mode register (i=0 to 5) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TB0MR to TB2MR TB3MR to TB5MR Address 039B16 to 039D16 035B16 to 035D16 After reset 00XX00002 00XX00002 Bit symbol TMOD0 TMOD1 Bit name Operation mode select bit b1 b0 Function 0 0 : Timer mode 0 1 : Event counter mode 1 0 : Pulse period measurement mode, pulse width measurement mode 1 1 : Must not be set Function varies with each operation mode RW RW RW RW RW RW (Note 1) (Note 2) MR0 MR1 MR2 MR3 TCK0 TCK1 Note 1: Timer B0, timer B3. Note 2: Timer B1, timer B2, timer B4, timer B5. Count source select bit Function varies with each operation mode RO RW RW Figure 9.15 TB0MR to TB5MR Registers Page 87 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS Timer Bi register (i=0 to 5)(Note 1) (b15) b7 (b8) b0 b7 b0 Symbol TB0 TB1 TB2 TB3 TB4 TB5 Address 039116, 039016 039316, 039216 039516, 039416 035116, 035016 035316, 035216 035516, 035416 After reset Indeterminate Indeterminate Indeterminate Indeterminate Indeterminate Indeterminate Mode Timer mode Event counter mode Function Divide the count source by n + 1 where n = set value Divide the count source by n + 1 where n = set value (Note 2) Setting range 000016 to FFFF16 000016 to FFFF16 RW RW RW Pulse period Measures a pulse period or width modulation mode, Pulse width modulation mode RO Note 1: The register must be accessed in 16 bit units. Note 2: The timer counts pulses from an external device or overflows or underflows of other timers. Count start flag b7 b6 b5 b4 b3 b2 b1 b0 Symbol TABSR Address 038016 After reset 0016 Bit symbol TA0S TA1S TA2S TA3S TA4S TB0S TB1S TB2S Bit name Timer A0 count start flag Timer A1 count start flag Timer A2 count start flag Timer A3 count start flag Timer A4 count start flag Timer B0 count start flag Timer B1 count start flag Timer B2 count start flag Function 0 : Stops counting 1 : Starts counting RW RW RW RW RW RW RW RW RW Timer B3, B4, B5 count start flag b7 b6 b5 b4 b3 b2 b1 b0 Symbol TBSR Address 034016 After reset 000XXXXX2 Bit symbol (b4-b0) TB3S TB4S TB5S Bit name Function RW Nothing is assigned. When write, set to "0". When read, their contents are indeterminate. Timer B3 count start flag Timer B4 count start flag Timer B5 count start flag 0 : Stops counting 1 : Starts counting RW RW RW Clock prescaler reset flag b7 b6 b5 b4 b3 b2 b1 b0 Symbol CPSRF Address 038116 After reset 0XXXXXXX2 Bit symbol (b6-b0) CPSR Bit name Function RW Nothing is assigned. When write, set to "0". When read, their contents are indeterminate. Clock prescaler reset flag Setting this bit to "1" initializes the RW prescaler for the timekeeping clock. (When read, the value of this bit is "0".) Figure 9.16 TB0 to TB5 Registers, TABSR Register, TBSR Register, CPSRF Register Page 88 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 9.2.1 Timer Mode In timer mode, the timer counts a count source generated internally (see Table 9.6). Figure 9.17 shows TBiMR register in timer mode. Table 9.6 Specifications in Timer Mode Specification f1, f2, f8, f32, fC32 * Down-count * When the timer underflows, it reloads the reload register contents and continues counting 1/(n+1) n: set value of TBi register (i= 0 to 5) Set TBiS bit(Note) to "1" (= start counting) Set TBiS bit to "0" (= stop counting) Timer underflow I/O port Count value can be read by reading TBi register 000016 to FFFF16 Item Count source Count operation Divide ratio Count start condition Count stop condition Interrupt request generation timing TBiIN pin function Read from timer Write to timer * When not counting and until the 1st count source is input after counting start Value written to TBi register is written to both reload register and counter * When counting (after 1st count source input) Value written to TBi register is written to only reload register (Transferred to counter when reloaded next) Note : The TB0S to TB2S bits are assigned to the TABSR register bit 5 to bit 7, and the TB3S to TB5S bits are assigned to the TBSR register bit 5 to bit 7. Timer Bi mode register (i= 0 to 5) b7 b6 b5 b4 b3 b2 b1 b0 00 Symbol TB0MR to TB2MR TB3MR to TB5MR Bit symbol TMOD0 TMOD1 MR0 MR1 MR2 Address 039B16 to 039D16 035B16 to 035D16 After reset 00XX00002 00XX00002 Bit name Operation mode select bit b1 b0 Function 0 0 : Timer mode RW RW RW RW RW RW Has no effect in timer mode Can be set to "0" or "1" TB0MR, TB3MR registers Must be set to "0" in timer mode TB1MR, TB2MR, TB4MR, TB5MR registers Nothing is assigned. When write, set to "0". When read, its content is indeterminate MR3 When write in timer mode, set to "0". When read in timer mode, its content is indeterminate. Count source select bit b7 b6 RO RW RW TCK0 TCK1 0 0 : f1 or f2 0 1 : f8 1 0 : f32 1 1 : fC32 Figure 9.17 TBiMR Register in Timer Mode Page 89 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 9.2.2 Event Counter Mode In event counter mode, the timer counts pulses from an external device or overflows and underflows of other timers (see Table 9.7) . Figure 9.18 shows TBiMR register in event counter mode. Table 9.7 Item Count source Specifications in Event Counter Mode Specification * External signals input to TBiIN pin (i=0 to 5) (effective edge can be selected in program) * Timer Bj overflow or underflow (j=i-1, except j=2 if i=0, j=5 if i=3) Count operation * Down-count * When the timer underflows, it reloads the reload register contents and continues counting Divide ratio 1/(n+1) n: set value of TBi register 000016 to FFFF16 Count start condition Set TBiS bit1 to "1" (= start counting) Count stop condition Set TBiS bit to "0" (= stop counting) Interrupt request generation timing Timer underflow TBiIN pin function Count source input Read from timer Count value can be read by reading TBi register Write to timer * When not counting and until the 1st count source is input after counting start Value written to TBi register is written to both reload register and counter * When counting (after 1st count source input) Value written to TBi register is written to only reload register (Transferred to counter when reloaded next) Notes: 1. The TB0S to TB2S bits are assigned to the TABSR register bit 5 to bit 7, and the TB3S to TB5S bits are assigned to the TBSR register bit 5 to bit 7. Timer Bi mode register (i=0 to 5) b7 b6 b5 b4 b3 b2 b1 b0 01 Symbol TB0MR to TB2MR TB3MR to TB5MR Address 039B16 to 039D16 035B16 to 035D16 After reset 00XX00002 00XX00002 Bit symbol TMOD0 TMOD1 MR0 Bit name Operation mode select bit b1 b0 Function 0 1 : Event counter mode b3 b2 RW RW RW RW Count polarity select bit (Note 1) MR1 0 0 : Counts external signal's falling edges 0 1 : Counts external signal's rising edges 1 0 : Counts external signal's falling and rising edges 1 1 : Must not be set RW MR2 TB0MR, TB3MR registers Must be set to "0" in event count mode TB1MR, TB2MR, TB4MR, TB5MR registers Nothing is assigned. When write, set to "0". When read, its content is indeterminate. RW MR3 When write in event counter mode, set to "0". When read in event counter mode, its content is indeterminate. Has no effect in event counter mode. Can be set to "0" or "1". Event clock select 0 : Input from TBiIN pin (Note 2) 1 : TBj overflow or underflow (j = i - 1, except j = 2 if i = 0, j = 5 if i = 3) RO TCK0 TCK1 RW RW Note 1: Effective when the TCK1 bit = "0" (input from TBiIN pin). If the TCK1 bit = "1" (TBj overflow or underflow), these bits can be set to "0" or "1". Note 2: The port direction bit for the TBiIN pin must be set to "0" (= input mode). Figure 9.18 TBiMR Register in Event Counter Mode Page 90 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS 9.2.3 Pulse Period and Pulse Width Measurement Mode In pulse period and pulse width measurement mode, the timer measures pulse period or pulse width of an external signal (see Table 9.8). Figure 9.19 shows TBiMR register in pulse period and pulse width measurement mode. Figure 9.20 shows the operation timing when measuring a pulse period. Figure 9.21 shows the operation timing when measuring a pulse width. Table 9.8 Specifications in Pulse Period and Pulse Width Measurement Mode Specification f1, f2, f8, f32, fC32 * Up-count * Counter value is transferred to reload register at an effective edge of mea- Item Count source Count operation surement pulse. The counter value is set to "000016" to continue counting. Count start condition Set TBiS (i=0 to 5) bit3 to "1" (= start counting) Count stop condition Set TBiS bit to "0" (= stop counting) Interrupt request generation timing * When an effective edge of measurement pulse is input1 * Timer overflow. When an overflow occurs, MR3 bit of TBiMR register is set to "1" (overflowed) simultaneously. MR3 bit is cleared to "0" (no overflow) by writing to TBiMR register at the next count timing or later after MR3 bit was set to "1". At this time, make sure TBiS bit is set to "1" (start counting). TBiIN pin function Measurement pulse input Read from timer Contents of the reload register (measurement result) can be read by reading TBi register2 Write to timer Value written to TBi register is written to neither reload register nor counter Notes: 1. Interrupt request is not generated when the first effective edge is input after the timer started counting. 2. Value read from TBi register is indeterminate until the second valid edge is input after the timer starts counting. 3. The TB0S to TB2S bits are assigned to the TABSR register bit 5 to bit 7, and the TB3S to TB5S bits are assigned to the TBSR register bit 5 to bit 7. Timer Bi mode register (i=0 to 5) b7 b6 b5 b4 b3 b2 b1 b0 10 Symbol TB0MR to TB2MR TB3MR to TB5MR Address 039B16 to 039D16 035B16 to 035D16 After reset 00XX00002 00XX00002 Bit symbol TMOD0 TMOD1 MR0 Bit name Operation mode select bit Measurement mode select bit b1 b0 Function 1 0 : Pulse period / pulse width measurement mode b3 b2 RW RW RW MR1 0 0 : Pulse period measurement (Measurement between a falling edge and the next falling edge of measured pulse) 0 1 : Pulse period measurement (Measurement between a rising edge and the next rising edge of measured pulse) 1 0 : Pulse width measurement (Measurement between a falling edge and the next rising edge of measured pulse and between a rising edge and the next falling edge) 1 1 : Must not be set. RW RW MR2 MR3 TCK0 TCK1 TB0MR and TB3MR registers Must be set to "0" in pulse period and pulse width measurement mode TB1MR, TB2MR, TB4MR, TB5MR registers Nothing is assigned. When write, set to "0". When read, its content turns out to be indeterminate. Timer Bi overflow 0 : Timer did not overflow flag ( Note) 1 : Timer has overflowed Count source select bit b7 b6 RW RO RW RW 0 0 : f1 or f2 0 1 : f8 1 0 : f32 1 1 : fC32 Note: This flag is indeterminate after reset. When the TBiS bit = 1 (start counting), the MR3 bit is cleared to "0" (no overflow) by writing to the TBiMR register at the next count timing or later after the MR3 bit was set to "1" (overflowed). The MR3 bit cannot be set to "1" in a program. The TB0S to TB2S bits are assigned to the TABSR register's bit 5 to bit 7, and the TB3S to TB5S bits are assigned to the TBSR register's bit 5 to bit 7. Figure 9.19 TBiMR Register in Pulse Period and Pulse Width Measurement Mode Page 91 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. TIMERS Count source Measurement pulse "H" "L" Transfer (indeterminate value) Transfer (measured value) Reload register transfer timing counter (Note 1) (Note 1) (Note 2) Timing at which counter reaches "000016" TBiS bit "1" "0" TBiIC register's IR bit "1" "0" TBiMR register's MR3 bit "1" "0" Set to "0" upon accepting an interrupt request or by writing in program The TB0S to TB2S bits are assigned to the TABSR register's bit 5 to bit 7, and the TB3S to TB5S bits are assigned to the TBSR register's bit 5 to bit 7. i = 0 to 5 Note 1: Counter is initialized at completion of measurement. Note 2: Timer has overflowed. Note 3: This timing diagram is for the case where the TBiMR register's MR1 to MR0 bits are "002" (measure the interval from falling edge to falling edge of the measurement pulse). Figure 9.20 Operation timing when measuring a pulse period Count source Measurement pulse "H" "L" Transfer (indeterminate value) Transfer (measured value) Transfer (measured value) Transfer (measured value) Reload register transfer timing counter (Note 1) (Note 1) (Note 1) (Note 1) (Note 2) Timing at which counter reaches "000016" TBiS bit "1" "0" TBiIC register's IR bit "1" "0" "1" Set to "0" upon accepting an interrupt request or by writing in program TBiMR register's MR3 bit "0" i = 0 to 5 The TB0S to TB2S bits are assigned to the TABSR register's bit 5 to bit 7, and the TB3S to TB5S bits are assigned to the TBSR register's bit 5 to bit 7. Note 1: Counter is initialized at completion of measurement. Note 2: Timer has overflowed. Note 3: This timing diagram is for the case where the TBiMR register's MR1 to MR0 bits are "102" (measure the interval from a falling edge to the next rising edge and the interval from a rising edge to the next falling edge of the measurement pulse). Figure 9.21 Operation timing when measuring a pulse width Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 92 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10. Serial I/O Serial I/O is configured with five channels: UART0 to UART2, SI/O3 and SI/O4. 10.1 UARTi (i=0 to 2) UARTi each have an exclusive timer to generate a transfer clock, so they operate independently of each other. Figure 10.1 shows the block diagram of UARTi. Figures 10.2 shows the block diagram of the UARTi transmit/ receive. UARTi has the following modes: * Clock synchronous serial I/O mode * Clock asynchronous serial I/O mode (UART mode). * Special mode 1 (I2C mode) * Special mode 2 * Special mode 3 (Bus collision detection function, IE mode) : UART0, UART1 * Special mode 4 (SIM mode) : UART2 Figures 10.3 to 10.8 show the UARTi-related registers. Refer to tables listing each mode for register setting. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 93 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 1/2 f2SIO f1SIO PCLK1=0 Main clock 1/8 f1SIO or f2SIO PCLK1=1 f8SIO 1/4 (UART0) RxD0 Clock source selection f1SIO or f2SIO f8SIO f32SIO CLK1 to CLK0 002 Internal CKDIR=0 012 102 External CKDIR=1 U0BRG register RxD polarity reversing circuit 1/16 UART reception Clock synchronous type UART transmission f32SIO TxD polarity reversing circuit TxD0 Reception control circuit Receive clock Transmit/ receive unit CKPOL CLK polarity reversing circuit Transmission control Clock synchronous circuit type Clock synchronous type (when internal clock is selected) 1/2 CKDIR=0 Clock synchronous type (when external clock is selected) CKDIR=1 Clock synchronous type (when internal clock is selected) 1 / (n0+1) 1/16 Transmit clock CLK0 CTS/RTS selected CRS=1 CTS/RTS disabled CTS0 / RTS0 RTS0 CRS=0 RCSP=0 CTS0 from UART1 RCSP=1 "H" CTS/RTS disabled CRD=1 CRD=0 CTS0 (UART1) RxD1 RxD polarity reversing circuit UART reception 1/16 Clock synchronous type 1/16 UART transmission Clock synchronous type Transmission control circuit Reception control circuit Receive clock Transmit/ receive unit Transmit clock Clock source selection CLK1 to CLK0 002 f1SIO or f2SIO Internal CKDIR=0 012 f8SIO 102 TxD polarity reversing circuit TxD1 U1BRG register f32SIO 1 / (n1+1) External CKDIR=1 CKPOL CLK1 CTS1 / RTS1/ CTS0/ CLKS1 CLK polarity reversing circuit Clock output pin select CLKMD1=1 CLKMD1=0 CLKMD0=0 CLKMD0=1 Clock synchronous type 1/2 (when internal clock is selected) CKDIR=0 Clock synchronous type (when external clock is selected) CKDIR=1 Clock synchronous type (when internal clock is selected) CTS/RTS selected CRS=1 CRS=0 CTS/RTS disabled RTS1 "H" CTS/RTS disabled RCSP=0 CRD=1 CRD=0 CTS1 CTS0 from UART0 RCSP=1 TxD polarity reversing circuit Reception control circuit Receive clock Transmit/ receive unit (Note) (UART2) RxD2 RxD polarity reversing circuit 1/16 Clock source selection CLK1 to CLK0 002 f1SIO or f2SIO 012 Internal CKDIR=0 f8SIO 102 TxD2 UART reception Clock synchronous type U2BRG register f32SIO 1 / (n2+1) 1/16 UART transmission Clock synchronous type Transmission control circuit Transmit clock External CKDIR=1 CKPOL CLK2 CLK polarity reversing circuit CTS/RTS selected CRS=1 Clock synchronous type 1/2 (when internal clock is selected) CKDIR=0 Clock synchronous type (when external clock is selected) CKDIR=1 Clock synchronous type (when internal clock is selected) CTS/RTS disabled RTS2 CTS2 / RTS2 CRS=0 "H" CTS/RTS disabled CRD=1 CRD=0 CTS2 i = 0 to 2 ni: Values set to the UiBRG register SMD2 to SMD0, CKDIR: UiMR register's bits CLK1 to CLK0, CKPOL, CRD, CRS: UiC0 register's bits CLKMD0, CLKMD1, RCSP: UCON register's bits Note: UART2 is the N-channel open-drain output. Cannot be set to the CMOS output. Figure 10.1 UARTi Block Diagram Page 94 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O No reverse IOPOL=0 RxDi RxD data reverse circuit Reverse IOPOL=1 Clock synchronous type 1SP PAR disabled PRYE=0 STPS= 0 Clock synchronous type UART (7 bits) UART (8 bits) UART(7 bits) UARTi receive register SP 2SP STPS= 1 SP PAR PRYE=1 PAR enabled UART UART (9 bits) Clock synchronous type UART (8 bits) UART (9 bits) 0 0 0 0 0 0 0 D8 D7 D6 D5 D4 D3 D2 D1 D0 UiRB register Logic reverse circuit + MSB/LSB conversion circuit Data bus high-order bits Data bus low-order bits Logic reverse circuit + MSB/LSB conversion circuit D8 UART (9 bits) D7 D6 D5 D4 D3 D2 D1 D0 UiTB register UART (8 bits) UART (9 bits) Clock synchronous type 2SP STPS= 1 enabled PRYE=1 UART SP SP STPS =0 PAR PAR PRYE=0 PAR disabled Clock synchronous type 1SP "0" UART (7 bits) UART (8 bits) Clock synchronous type UARTi transmit register UART(7 bits) i=0 to 2 SP: Stop bit PAR: Parity bit SMD2 to SMD0, STPS, PRYE, IOPOL, CKDIR: UiMR register's bits UiERE: UiC1 register's bit Error signal output disable UiERE=0 IOPOL=0 No reverse UiERE=1 Error signal output circuit Error signal output enable IOPOL=1 TxD data reverse circuit Reverse TxDi Figure 10.2 UARTi Transmit/Receive Unit Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 95 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O UARTi transmit buffer register (i=0 to 2)(Note) (b15) b7 (b8) b0 b7 b0 Symbol U0TB U1TB U2TB Address 03A316-03A216 03AB16-03AA16 037B16-037A16 After reset Indeterminate Indeterminate Indeterminate Function RW WO Transmit data Nothing is assigned. In an attempt to write to these bits, write "0". The value, if read, turns out to be indeterminate. Note: Use MOV instruction to write to this register. UARTi receive buffer register (i=0 to 2) (b15) b7 (b8) b0 b7 b0 Symbol U0RB U1RB U2RB Address 03A716-03A616 03AF16-03AE16 037F16-037E16 After reset Indeterminate Indeterminate Indeterminate Bit symbol (b7-b0) (b8) (b10-b9) ABT OER FER PER SUM Bit name Receive data (D7 to D0) Receive data (D8) Function RW RO RO Nothing is assigned. In an attempt to write to these bits, write "0". The value, if read, turns out to be "0". Arbitration lost detecting flag (Note 2) 0 : Not detected 1 : Detected RW RO RO RO Overrun error flag (Note 1) 0 : No overrun error 1 : Overrun error found Framing error flag (Note 1) Parity error flag (Note 1) Error sum flag (Note 1) 0 : No framing error 1 : Framing error found 0 : No parity error 1 : Parity error found 0 : No error 1 : Error found RO Note 1: When the UiMR register's SMD2 to SMD0 bits = "0002" (serial I/O disabled) or the UiC1 register's RE bit = "0" (reception disabled), all of the SUM, PER, FER and OER bits are set to "0" (no error). The SUM bit is set to "0" (no error) when all of the PER, FER and OER bits = "0" (no error). Also, the PER and FER bits are set to "0" by reading the lower byte of the UiRB register. Note 2: The ABT bit is set to "0" by writing "0" in a program. (Writing "1" has no effect.) UARTi bit rate generator (i=0 to 2)(Notes 1, 2) b7 b0 Symbol U0BRG U1BRG U2BRG Address 03A116 03A916 037916 Function After reset Indeterminate Indeterminate Indeterminate Setting range 0016 to FF16 RW WO Assuming that set value = n, UiBRG divides the count source by n + 1 Note 1: Write to this register while serial I/O is neither transmitting nor receiving. Note 2: Use MOV instruction to write to this register. Figure 10.3 U0TB to U2TB Register, U0RB to U2RB Register, and U0BRG to U2BRG Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 96 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O UARTi transmit/receive mode register (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol U0MR to U2MR Bit symbol SMD0 SMD1 SMD2 Address 03A016, 03A816, 037816 After reset 0016 Function Bit name Serial I/O mode select bit (Note 2) b2 b1 b0 RW RW RW RW RW RW RW RW RW 0 0 0 : Serial I/O disabled 0 0 1 : Clock synchronous serial I/O mode (Note 3) 0 1 0 : I2C mode 1 0 0 : UART mode transfer data 7 bits long 1 0 1 : UART mode transfer data 8 bits long 1 1 0 : UART mode transfer data 9 bits long Must not be set except above 0 : Internal clock 1 : External clock (Note 1) 0 : One stop bit 1 : Two stop bits CKDIR Internal/external clock select bit STPS PRY Stop bit length select bit Odd/even parity select bit Effective when PRYE = 1 0 : Odd parity 1 : Even parity Parity enable bit TxD, RxD I/O polarity reverse bit 0 : Parity disabled 1 : Parity enabled 0 : No reverse 1 : Reverse PRYE IOPOL Note 1: Set the corresponding port direction bit for each CLKi pin to "0" (input mode). Note 2: To receive data, set the corresponding port direction bit for each RxDi pin to "0" (input mode). Note 3: Set the corresponding port direction bit for SCL and SDA pins to "0" (input mode). UARTi transmit/receive control register 0 (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol U0C0 to U2C0 Address After reset 03A416, 03AC16, 037C16 000010002 Bit symbol CLK0 CLK1 CRS Bit name BRG count source select bit b1 b0 Function 0 0 : f1SIO or f2SIO is selected 0 1 : f8SIO is selected 1 0 : f32SIO is selected 1 1 : Must not be set Effective when CRD = 0 0 : CTS function is selected (Note 1) 1 : RTS function is selected RW RW RW CTS/RTS function select bit (Note 4) RW TXEPT Transmit register empty 0 : Data present in transmit register (during transmission) 1 : No data present in transmit register flag (transmission completed) CTS/RTS disable bit 0 : CTS/RTS function enabled 1 : CTS/RTS function disabled (P60, P64 and P73 can be used as I/O ports) 0 : TxDi/SDAi and SCLi pins are CMOS output 1 : TxDi/SDAi and SCLi pins are N-channel open-drain output 0 : Transmit data is output at falling edge of transfer clock and receive data is input at rising edge 1 : Transmit data is output at rising edge of transfer clock and receive data is input at falling edge RO CRD RW NCH CKPOL Data output select bit (Note 2) CLK polarity select bit RW RW UFORM Transfer format select bit 0 : LSB first (Note 3) 1 : MSB first RW Note 1: Set the corresponding port direction bit for each CTSi pin to "0" (input mode). Note 2: TXD2/SDA2 and SCL2 are N-channel open-drain output. Cannot be set to the CMOS output. Set the NCH bit of the U2C0 register to "0". Note 3: Effective for clock synchronous serial I/O mode and UART mode transfer data 8 bits long. Note 4: CTS1/RTS1 can be used when the UCON register's CLKMD1 bit = "0" (only CLK1 output) and the UCON register's RCSP bit = "0" (CTS0/RTS0 not separated). Figure 10.4 U0MR to U2MR Register and U0C0 to U2C0 Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 97 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O UARTi transmit/receive control register 1 (i=0, 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol U0C1, U1C1 Address 03A516,03AD16 After reset 000000102 Bit symbol TE TI RE RI Bit name Transmit enable bit Transmit buffer empty flag Receive enable bit Receive complete flag Function 0 : Transmission disabled 1 : Transmission enabled 0 : Data present in UiTB register 1 : No data present in UiTB register 0 : Reception disabled 1 : Reception enabled 0 : No data present in UiRB register 1 : Data present in UiRB register RW RW RO RW RO (b5-b4) UiLCH UiERE Nothing is assigned. When write, set "0". When read, these contents are "0". Data logic select bit Error signal output enable bit 0 : No reverse 1 : Reverse 0 : Output disabled 1 : Output enabled RW RW UART2 transmit/receive control register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol U2C1 Address 037D16 After reset 000000102 Bit symbol TE TI RE RI Bit name Transmit enable bit Transmit buffer empty flag Receive enable bit Receive complete flag Function 0 : Transmission disabled 1 : Transmission enabled 0 : Data present in U2TB register 1 : No data present in U2TB register 0 : Reception disabled 1 : Reception enabled 0 : No data present in U2RB register 1 : Data present in U2RB register 0 : Transmit buffer empty (TI = 1) 1 : Transmit is completed (TXEPT = 1) 0 : Continuous receive mode disabled 1 : Continuous receive mode enabled 0 : No reverse 1 : Reverse 0 : Output disabled 1 : Output enabled RW RW RO RW RO RW RW RW RW U2IRS UART2 transmit interrupt cause select bit U2RRM UART2 continuous receive mode enable bit U2LCH Data logic select bit U2ERE Error signal output enable bit Figure 10.5 U0C1 to U2C1 Registers Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 98 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O UART transmit/receive control register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol UCON Address 03B016 After reset X00000002 Bit symbol U0IRS Bit name UART0 transmit interrupt cause select bit UART1 transmit interrupt cause select bit Function 0 : Transmit buffer empty (Tl = 1) 1 : Transmission completed (TXEPT = 1) 0 : Transmit buffer empty (Tl = 1) 1 : Transmission completed (TXEPT = 1) 0 : Continuous receive mode disabled 1 : Continuous receive mode enable 0 : Continuous receive mode disabled 1 : Continuous receive mode enabled Effective when CLKMD1 = "1" 0 : Clock output from CLK1 1 : Clock output from CLKS1 0 : CLK output is only CLK1 1 : Transfer clock output from multiple pins function selected 0 : CTS/RTS shared pin 1 : CTS/RTS separated (CTS0 supplied from the P64 pin) RW RW U1IRS RW RW RW RW U0RRM UART0 continuous receive mode enable bit U1RRM UART1 continuous receive mode enable bit CLKMD0 UART1 CLK/CLKS select bit 0 CLKMD1 UART1 CLK/CLKS select bit 1 (Note) RCSP Separate UART0 CTS/RTS bit RW RW (b7) Nothing is assigned. When write, set "0". When read, its content is indeterminate. Note: When using multiple transfer clock output pins, make sure the following conditions are met: U1MR register's CKDIR bit = "0" (internal clock) UART2 special mode register (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol Address U0SMR to U2SMR 036F16, 037316, 037716 Bit symbol IICM ABC BBS After reset X00000002 Bit name I2C mode select bit Arbitration lost detecting flag control bit Bus busy flag Reserved bit Bus collision detect sampling clock select bit Auto clear function select bit of transmit enable bit Transmit start condition select bit 0 : Other than I2C mode 1 : I2C mode 0 : Update per bit 1 : Update per byte Function RW RW RW RW (Note1) 0 : STOP condition detected 1 : START condition detected (busy) Set to "0" 0 : Rising edge of transfer clock 1 : Underflow signal of timer Aj (Note 2) 0 : No auto clear function 1 : Auto clear at occurrence of bus collision 0 : Not synchronized to RxDi 1 : Synchronized to RxDi (Note 3) (b3) ABSCS ACSE RW RW RW SSS RW Nothing is assigned. When write, set "0". When read, its content is indeterminate. (b7) Note 1: The BBS bit is set to "0" by writing "0" in a program. (Writing "1" has no effect.). Note 2: Underflow signal of timer A3 in UART0, underflow signal of timer A4 in UART1, underflow signal of timer A0 in UART2. Note 3: When a transfer begins, the SSS bit is set to "0" (Not synchronized to RxDi) Figure 10.6 UCON Register and U0SMR to U2SMR Registers Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 99 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O UARTi special mode register 2 (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address U0SMR2 to U2SMR2 036E16, 037216, 037616 Bit symbol IICM2 CSC SWC ALS STAC SWC2 SDHI After reset X00000002 Bit name I 2C mode select bit 2 Clock-synchronous bit SCL wait output bit SDA output stop bit UARTi initialization bit SCL wait output bit 2 SDA output disable bit Refer to Table 10.12 0 : Disabled 1 : Enabled 0 : Disabled 1 : Enabled 0 : Disabled 1 : Enabled 0 : Disabled 1 : Enabled 0: Transfer clock 1: "L" output Function RW RW RW RW RW RW RW RW 0: Enabled 1: Disabled (high impedance) (b7) Nothing is assigned. When write, set "0". When read, its content is indeterminate. UARTi special mode register 3 (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol U0SMR3 to U2SMR3 Bit symbol (b0) CKPH Address 036D16, 037116, 037516 After reset 000X0X0X2 Bit name Function RW Nothing is assigned. When write, set "0". When read, its content is indeterminate. Clock phase set bit 0 : Without clock delay 1 : With clock delay RW (b2) NODC Nothing is assigned. When write, set "0". When read, its content is indeterminate. Clock output select bit 0 : CLKi is CMOS output 1 : CLKi is N-channel open drain output RW (b4) DL0 Nothing is assigned. When write, set "0". When read, its content is indeterminate. SDAi digital delay setup bit (Note 1, Note 2) b7 b6 b5 DL1 DL2 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 : Without delay 1 : 1 to 2 cycle(s) of UiBRG count source 0 : 2 to 3 cycles of UiBRG count source 1 : 3 to 4 cycles of UiBRG count source 0 : 4 to 5 cycles of UiBRG count source 1 : 5 to 6 cycles of UiBRG count source 0 : 6 to 7 cycles of UiBRG count source 1 : 7 to 8 cycles of UiBRG count source RW RW RW Note 1 : The DL2 to DL0 bits are used to generate a delay in SDAi output by digital means during I2C mode. In other than I2C mode, set these bits to "0002" (no delay). Note 2 : The amount of delay varies with the load on SCLi and SDAi pins. Also, when using an external clock, the amount of delay increases by about 100 ns. Figure 10.7 U0SMR2 to U2SMR2 Registers and U0SMR3 to U2SMR3 Registers Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 100 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O UARTi special mode register 4 (i=0 to 2) b7 b6 b5 b4 b3 b2 b1 b0 Address Symbol U0SMR4 to U2SMR4 036C16, 037016, 037416 Bit symbol STAREQ After reset 0016 Bit name Start condition generate bit (Note) 0 : Clear 1 : Start 0 : Clear 1 : Start 0 : Clear 1 : Start Function RW RW RW RW RW RW RW RW RW RSTAREQ Restart condition generate bit (Note) STPREQ STSPSEL ACKD ACKC SCLHI SWC9 Stop condition generate bit (Note) SCL,SDA output select bit ACK data bit ACK data output enable bit SCL output stop enable bit SCL wait bit 3 0 : Start and stop conditions not output 1 : Start and stop conditions output 0 : ACK 1 : NACK 0 : Serial I/O data output 1 : ACK data output 0 : Disabled 1 : Enabled 0 : SCL "L" hold disabled 1 : SCL "L" hold enabled Note: Set to "0" when each condition is generated. Figure 10.8 U0SMR4 to U2SMR4 Registers Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 101 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.2 Clock Synchronous serial I/O Mode The clock synchronous serial I/O mode uses a transfer clock to transmit and receive data. Table 10.1 lists the specifications of the clock synchronous serial I/O mode. Table 10.2 lists the registers used in clock synchronous serial I/O mode and the register values set. Table 10.1 Clock Synchronous Serial I/O Mode Specifications Item Transfer data format Transfer clock * Transfer data length: 8 bits * UiMR(i=0 to 2) register's CKDIR bit = "0" (internal clock) : fj/ 2(n+1) fj = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of UiBRG register 0016 to FF16 * CKDIR bit = "1" (external clock) : Input from CLKi pin _______ _______ _______ _______ * Selectable from CTS function, RTS function or CTS/RTS function disable * Before transmission can start, the following requirements must be met (Note 1) _ The TE bit of UiC1 register= 1 (transmission enabled) _ _ Specification Transmission, reception control Transmission start condition The TI bit of UiC1 register = 0 (data present in UiTB register) _______ _______ If CTS function is selected, input on the CTSi pin = "L" The RE bit of UiC1 register= 1 (reception enabled) The TE bit of UiC1 register= 1 (transmission enabled) Reception start condition * Before reception can start, the following requirements must be met (Note 1) _ _ _ Interrupt request generation timing The TI bit of UiC1 register= 0 (data present in the UiTB register) * For transmission, one of the following conditions can be selected _ The UiIRS bit (Note 3) = 0 (transmit buffer empty): when transferring data from the UiTB register to the UARTi transmit register (at start of transmission) _ The UiIRS bit =1 (transfer completed): when the serial I/O finished sending data from the UARTi transmit register * For reception When transferring data from the UARTi receive register to the UiRB register (at Error detection completion of reception) * Overrun error (Note 2) This error occurs if the serial I/O started receiving the next data before reading the UiRB register and received the 7th bit of the next data * CLK polarity selection Transfer data input/output can be chosen to occur synchronously with the rising or the falling edge of the transfer clock * LSB first, MSB first selection Whether to start sending/receiving data beginning with bit 0 or beginning with bit 7 can be selected * Continuous receive mode selection Reception is enabled immediately by reading the UiRB register * Switching serial data logic This function reverses the logic value of the transmit/receive data * Transfer clock output from multiple pins selection (UART1) The output pin can be selected in a program from two UART1 transfer clock pins that have been set _______ _______ Select function * Separate CTS/RTS pins (UART0) _________ _________ CTS0 and RTS0 are input/output from separate pins Note 1: When an external clock is selected, the conditions must be met while if the UiC0 register's CKPOL bit = "0" (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock), the external clock is in the high state; if the UiC0 register's CKPOL bit = "1" (transmit data output at the rising edge and the receive data taken in at the falling edge of the transfer clock), the external clock is in the low state. Note 2: If an overrun error occurs, the value of UiRB register will be indeterminate. The IR bit of SiRIC register does not change. Note 3: The U0IRS and U1IRS bits respectively are the UCON register bits 0 and 1; the U2IRS bit is the U2C1 register bit 4. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 102 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 10.2 Register UiTB(Note3) 10. SERIAL I/O Registers to Be Used and Settings in Clock Synchronous Serial I/O Mode Bit 0 to 7 OER Function Set transmission data Reception data can be read Overrun error flag Set a transfer rate Set to "0012" Select the internal clock or external clock Set to "0" Select the count source for the UiBRG register _______ _______ UiRB(Note3) 0 to 7 UiBRG 0 to 7 CKDIR IOPOL UiC0 CLK1 to CLK0 CRS TXEPT CRD NCH CKPOL UFORM UiC1 TE TI RE RI U2IRS (Note 1) U2RRM (Note 1) UiLCH UiERE UiSMR UiSMR2 UiSMR3 0 to 7 0 to 7 0 to 2 NODC 4 to 7 UiSMR4 UCON 0 to 7 U0IRS, U1IRS U0RRM, U1RRM CLKMD0 CLKMD1 RCSP 7 UiMR(Note3) SMD2 to SMD0 Select CTS or RTS to use Transmit register empty flag _______ _______ Enable or disable the CTS or RTS function Select TxDi pin output mode (Note 2) Select the transfer clock polarity Select the LSB first or MSB first Set this bit to "1" to enable transmission/reception Transmit buffer empty flag Set this bit to "1" to enable reception Reception complete flag Select the source of UART2 transmit interrupt Set this bit to "1" to use continuous receive mode Set this bit to "1" to use inverted data logic Set to "0" Set to "0" Set to "0" Set to "0" Select clock output mode Set to "0" Set to "0" Select the source of UART0/UART1 transmit interrupt Set this bit to "1" to use continuous receive mode Select the transfer clock output pin when CLKMD1 = 1 Set this bit to "1" to output UART1 transfer clock from two pins _________ Set this bit to "1" to accept as input the UART0 CTS0 signal from the P64 pin Set to "0" Note 1: Set the U0C1 and U1C1 register bit 4 and bit 5 to "0". The U0IRS, U1IRS, U0RRM and U1RRM bits are in the UCON register. Note 2: TxD2 pin is N channel open-drain output. Set the U2C0 register's NCH bit to "0". Note 3: Not all register bits are described above. Set those bits to "0" when writing to the registers in clock synchronous serial I/O mode. i=0 to 2 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 103 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O Table 10.3 lists the functions of the input/output pins during clock synchronous serial I/O mode. Table 10.3 shows pin functions for the case where the multiple transfer clock output pin select function is deselected. Table 10.4 lists the P64 pin functions during clock synchronous serial I/O mode. Note that for a period from when the UARTi operation mode is selected to when transfer starts, the TxDi pin outputs an "H". (If the N-channel open-drain output is selected, this pin is in a high-impedance state.) Table 10.3 Pin name Pin Functions (When Not Select Multiple Transfer Clock Output Pin Function) Function Method of selection (Outputs dummy data when performing reception only) PD6 register's PD6_2 bit=0, PD6_6 bit=0, PD7 register's PD7_1 bit=0 (Can be used as an input port when performing transmission only) UiMR register's CKDIR bit=0 UiMR register's CKDIR bit=1 PD6 register's PD6_1 bit=0, PD6_5 bit=0, PD7 register's PD7_2 bit=0 UiC0 register's CRD bit=0 UiC0 register's CRS bit=0 PD6 register's PD6_0 bit=0, PD6_4 bit=0, PD7 register's PD7_3 bit=0 UiC0 register's CRD bit=0 UiC0 register's CRS bit=1 UiC0 register's CRD bit=1 TxDi (i = 0 to 2) Serial data output (P63, P67, P70) Serial data input RxDi (P62, P66, P71) CLKi Transfer clock output (P61, P65, P72) Transfer clock input CTSi/RTSi CTS input (P60, P64, P73) RTS output I/O port Table 10.4 Pin function P64 CTS1 RTS1 CTS0(Note1) CLKS1 P64 Pin Functions Bit set value U1C0 register CRS CRD 1 0 0 1 0 0 0 UCON register RCSP CLKMD1 CLKMD0 0 0 0 0 0 0 1 0 1(Note 2) 1 PD6 register PD6_4 Input: 0, Output: 1 0 0 Note 1: In addition to this, set the U0C0 register's CRD bit to "0" (CTS0/RTS0 enabled) and the U0 C0 register's CRS bit to "1" (RTS0 selected). Note 2: When the CLKMD1 bit = 1 and the CLKMD0 bit = 0, the following logic levels are output: * High if the U1C0 register's CLKPOL bit = 0 * Low if the U1C0 register's CLKPOL bit = 1 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 104 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O (1) Example of transmit timing (when internal clock is selected) Tc Transfer clock "1" "0" "1" "0" Transferred from UiTB register to UARTi transmit register "H" Write data to the UiTB register UiC1 register TE bit UiC1 register TI bit CTSi "L" TCLK Stopped pulsing because CTSi = "H" Stopped pulsing because the TE bit = "0" CLKi TxDi UiC0 register TXEPT bit SiTIC register IR bit "1" "0" "1" "0" D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Cleared to "0" when interrupt request is accepted, or cleared to "0" in a program Tc = TCLK = 2(n + 1) / fj fj: frequency of UiBRG count source (f1SIO, f2SIO, f8SIO, f32SIO) n: value set to UiBRG register i: 0 to 2 The above timing diagram applies to the case where the register bits are set as follows: * UiMR register CKDIR bit = 0 (internal clock) * UiC0 register CRD bit = 0 (CTS/RTS enabled), CRS bit = 0 (CTS selected) * UiC0 register CKPOL bit = 0 (transmit data output at the falling edge and receive data taken in at the rising edge of the transfer clock) * UiRS bit = 0 (an interrupt request occurs when the transmit buffer becomes empty): U0IRS bit is the UCON register bit 0, U1IRS bit is the UCON register bit 1, and U2IRS bit is the U2C1 register bit 4 (2) Example of receive timing (when external clock is selected) UiC1 register RE bit UiC1 register TE bit UiC1 register TI bit RTSi "1" "0" "1" "0" "1" "0" "H" "L" Write dummy data to UiTB register Transferred from UiTB register to UARTi transmit register Even if the reception is completed, the RTS does not change. The RTS becomes "L" when the RI bit changes to "0" from "1". 1 / fEXT CLKi Receive data is taken in RxDi UiC1 register RI bit SiRIC register IR bit "1" "0" "1" "0" D0 D1 D2 D3 D4 D5 D6 D7 Transferred from UARTi receive register to UiRB register D0 D1 D2 D3 D4 D5 Read out from UiRB register Cleared to "0" when interrupt request is accepted, or cleared to "0" in a program The above timing diagram applies to the case where the register bits are set Make sure the following conditions are met when input as follows: to the CLKi pin before receiving data is high: * UiMR register CKDIR bit = 1 (external clock) * UiC1 register TE bit = 1 (transmit enabled) * UiC0 register CRD bit = 0 (CTS/RTS enabled), CRS bit = 1 (RTS selected) * UiC1 register RE bit = 1 (Receive enabled) * UiC0 register CKPOL bit = 0 (transmit data output at the falling edge and receive * Write dummy data to the UiTB register data taken in at the rising edge of the transfer clock) fEXT: frequency of external clock Figure 10.9 Transmit and Receive Operation Page 105 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.2.1 CLK Polarity Select Function Use the UiC0 register (i = 0 to 2)'s CKPOL bit to select the transfer clock polarity. Figure 10.10 shows the polarity of the transfer clock. (1) When the UiC0 register's CKPOL bit = 0 (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock) CLKi TXDi RXDi D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7 (Note 2) (2) When the UiC0 register's CKPOL bit = 1 (transmit data output at the rising edge and the receive data taken in at the falling edge of the transfer clock) CLKi TXDi RXDi D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7 (Note 3) Note 1: This applies to the case where the UiC0 register's UFORM bit = 0 (LSB first) and UiC1 register's UiLCH bit = 0 (no reverse). Note 2: When not transferring, the CLKi pin outputs a high signal. Note 3: When not transferring, the CLKi pin outputs a low signal. i = 0 to 2 Figure 10.10 Transfer Clock Polarity 10.2.2 LSB First/MSB First Select Function Use the UiC0 register (i = 0 to 2)'s UFORM bit to select the transfer format. Figure 10.11 shows the transfer format. (1) When UiC0 register's UFORM bit = 0 (LSB first) CLKi TXDi RXDi D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7 (2) When UiC0 register's UFORM bit = 1 (MSB first) CLKi TXDi RXDi D7 D7 D6 D6 D5 D5 D4 D4 D3 D3 D2 D2 D1 D1 D0 D0 Note: This applies to the case where the UiC0 register's CKPOL bit = 0 (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock) and the UiC1 register's UiLCH bit = 0 (no reverse). i = 0 to 2 Figure 10.11 Transfer Format Page 106 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.2.3 Continuous Receive Mode When the UiRRM bit (i = 0 to 2) = 1 (continuous receive mode), the UiC1 register's TI bit is set to "0" (data present in the UiTB register) by reading the UiRB register. In this case, i.e., UiRRM bit = 1, do not write dummy data to the UiTB register in a program. The U0RRM and U1RRM bits are the UCON register bit 2 and bit 3, respectively, and the U2RRM bit is the U2C1 register bit 5. 10.2.4 Serial Data Logic Switching Function When the UiC1 register (i = 0 to 2)'s UiLCH bit = 1 (reverse), the data written to the UiTB register has its logic reversed before being transmitted. Similarly, the received data has its logic reversed when read from the UiRB register. Figure 10.12 shows serial data logic. (1) When the UiC1 register's UiLCH bit = 0 (no reverse) Transfer clock TxDi "H" "L" "H" (no reverse) "L" D0 D1 D2 D3 D4 D5 D6 D7 (2) When the UiC1 register's UiLCH bit = 1 (reverse) Transfer clock TxDi (reverse) "H" "L" "H" "L" D0 D1 D2 D3 D4 D5 D6 D7 Note: This applies to the case where the UiC0 register's CKPOL bit = 0 (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock) and the UFORM bit = 0 (LSB first). i = 0 to 2 Figure 10.12 Serial Data Logic Switching 10.2.5 Transfer Clock Output From Multiple Pins (UART1) Use the UCON register's CLKMD1 to CLKMD0 bits to select one of the two transfer clock output pins. (See Figure 10.13.) This function can be used when the selected transfer clock for UART1 is an internal clock. Microcomputer TXD1 (P67) CLKS1 (P64) CLK1 (P65) IN CLK IN CLK Transfer enabled when the UCON register's CLKMD0 bit = 0 Transfer enabled when the UCON register's CLKMD0 bit = 1 Note: This applies to the case where the U1MRregister's CKDIR bit = 0 (internal clock) and the UCON register's CLKMD1 bit = 1 (transfer clock output from multiple pins). Figure 10.13 Transfer Clock Output From Multiple Pins Page 107 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.2.6 CTS/RTS Separate Function (UART0) This function separates CTS0/RTS0, outputs RTS0 from the P60 pin, and accepts as input the CTS0 from the P64 pin. To use this function, set the register bits as shown below. * U0C0 register's CRD bit = 0 (enables UART0 CTS/RTS) * U0C0 register's CRS bit = 1 (outputs UART0 RTS) * U1C0 register's CRD bit = 0 (enables UART1 CTS/RTS) * U1C0 register's CRS bit = 0 (inputs UART1 CTS) * UCON register's RCSP bit = 1 (inputs CTS0 from the P64 pin) * UCON register's CLKMD1 bit = 0 (CLKS1 not used) Note that when using the CTS/RTS separate function, UART1 CTS/RTS function cannot be used. Microcomputer TXD0 (P63) RXD0 (P62) CLK0 (P61) IN OUT CLK IC RTS0 (P60) CTS0 (P64) CTS RTS Figure 10.14 CTS/RTS Separat Function Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 108 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.3 Clock Asynchronous Serial I/O (UART) Mode The UART mode allows transmitting and receiving data after setting the desired transfer rate and transfer data format. Tables 10.5 lists the specifications of the UART mode. Table 10.5 UART Mode Specifications Specification * Character bit (transfer data): Selectable from 7, 8 or 9 bits * Start bit: 1 bit * Parity bit: Selectable from odd, even, or none * Stop bit: Selectable from 1 or 2 bits * UiMR(i=0 to 2) register's CKDIR bit = 0 (internal clock) : fj/ 16(n+1) fj = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of UiBRG register 0016 to FF16 * CKDIR bit = "1" (external clock) : fEXT/16(n+1) fEXT: Input from CLKi pin. n :Setting value of UiBRG register 0016 to FF16 _______ _______ _______ _______ * Selectable from CTS function, RTS function or CTS/RTS function disable * Before transmission can start, the following requirements must be met _ The TE bit of UiC1 register= 1 (transmission enabled) _ The TI bit of UiC1 register = 0 (data present in UiTB register) _______ _______ _ If CTS function is selected, input on the CTSi pin = "L" * Before reception can start, the following requirements must be met _ The RE bit of UiC1 register= 1 (reception enabled) _ Start bit detection * For transmission, one of the following conditions can be selected _ The UiIRS bit (Note 2) = 0 (transmit buffer empty): when transferring data from the UiTB register to the UARTi transmit register (at start of transmission) _ The UiIRS bit =1 (transfer completed): when the serial I/O finished sending data from the UARTi transmit register * For reception When transferring data from the UARTi receive register to the UiRB register (at completion of reception) * Overrun error (Note 1) This error occurs if the serial I/O started receiving the next data before reading the UiRB register and received the bit one before the last stop bit of the next data * Framing error This error occurs when the number of stop bits set is not detected * Parity error This error occurs when if parity is enabled, the number of 1's in parity and character bits does not match the number of 1's set * Error sum flag This flag is set (= 1) when any of the overrun, framing, and parity errors is encountered Item Transfer data format Transfer clock Transmission, reception control Transmission start condition Reception start condition Interrupt request generation timing Error detection * LSB first, MSB first selection Whether to start sending/receiving data beginning with bit 0 or beginning with bit 7 can be selected * Serial data logic switch This function reverses the logic of the transmit/receive data. The start and stop bits are not reversed. * TXD, RXD I/O polarity switch This function reverses the polarities of hte TXD pin output and RXD pin input. The logic levels of all I/O data is reversed. _______ _______ * Separate CTS/RTS pins (UART0) _________ _________ CTS0 and RTS0 are input/output from separate pins Note 1: If an overrun error occurs, the value of UiRB register will be indeterminate. The IR bit of SiRIC register does not change. Note 2: The U0IRS and U1IRS bits respectively are the UCON register bits 0 and 1; the U2IRS bit is the U2C1 register bit 4. Select function Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 109 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 10.6 Register UiTB UiRB UiBRG UiMR 10. SERIAL I/O Registers to Be Used and Settings in UART Mode Bit 0 to 8 0 to 8 0 to 7 SMD2 to SMD0 Function Set transmission data (Note 1) Reception data can be read (Note 1) Set a transfer rate Set these bits to `1002' when transfer data is 7 bits long Set these bits to `1012' when transfer data is 8 bits long Set these bits to `1102' when transfer data is 9 bits long CKDIR STPS PRY, PRYE IOPOL Select the internal clock or external clock Select the stop bit Select whether parity is included and whether odd or even Select the TxD/RxD input/output polarity Select the count source for the UiBRG register _______ _______ OER,FER,PER,SUM Error flag UiC0 CLK0, CLK1 CRS TXEPT CRD NCH CKPOL UFORM Select CTS or RTS to use Transmit register empty flag _______ _______ Enable or disable the CTS or RTS function Select TxDi pin output mode (Note 3) Set to "0" LSB first or MSB first can be selected when transfer data is 8 bits long. Set this bit to "0" when transfer data is 7 or 9 bits long. Set this bit to "1" to enable transmission Transmit buffer empty flag Set this bit to "1" to enable reception Reception complete flag Select the source of UART2 transmit interrupt Set to "0" Set this bit to "1" to use inverted data logic Set to "0" Set to "0" Set to "0" Set to "0" Set to "0" Select the source of UART0/UART1 transmit interrupt Set to "0" Invalid because CLKMD1 = 0 Set to "0" _________ UiC1 TE TI RE RI U2IRS (Note 2) U2RRM (Note 2) UiLCH UiERE UiSMR UiSMR2 UiSMR3 UiSMR4 UCON 0 to 7 0 to 7 0 to 7 0 to 7 U0IRS, U1IRS U0RRM, U1RRM CLKMD0 CLKMD1 RCSP 7 Set this bit to "1" to accept as input the UART0 CTS0 signal from the P64 pin Set to "0" Note 1: The bits used for transmit/receive data are as follows: Bit 0 to bit 6 when transfer data is 7 bits long; bit 0 to bit 7 when transfer data is 8 bits long; bit 0 to bit 8 when transfer data is 9 bits long. Note 2: Set the U0C1 and U1C1 registers bit 4 to bit 5 to "0". The U0IRS, U1IRS, U0RRM and U1RRM bits are included in the UCON register. Note 3: TxD2 pin is N channel open-drain output. Set the U2C0 register's NCH bit to "0". i=0 to 2 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 110 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O Table 10.7 lists the functions of the input/output pins during UART mode. Table 10.8 lists the P64 pin functions during UART mode. Note that for a period from when the UARTi operation mode is selected to when transfer starts, the TxDi pin outputs an "H". (If the N-channel open-drain output is selected, this pin is in a high-impedance state.) Table 10.7 Pin name I/O Pin Functions Function Method of selection (Outputs dummy data when performing reception only) PD6 register's PD6_2 bit=0, PD6_6 bit=0, PD7 register's PD7_1 bit=0 (Can be used as an input port when performing transmission only) UiMR register's CKDIR bit=0 UiMR register's CKDIR bit=1 PD6 register's PD6_1 bit=0, PD6_5 bit=0, PD7 register's PD7_2 bit=0 UiC0 register's CRD bit=0 UiC0 register's CRS bit=0 PD6 register's PD6_0 bit=0, PD6_4 bit=0, PD7 register's PD7_3 bit=0 UiC0 register's CRD bit=0 UiC0 register's CRS bit=1 UiC0 register's CRD bit=1 TxDi (i = 0 to 2) Serial data output (P63, P67, P70) Serial data input RxDi (P62, P66, P71) CLKi Input/output port (P61, P65, P72) Transfer clock input CTSi/RTSi CTS input (P60, P64, P73) RTS output Input/output port Table 10.8 Pin function P64 CTS1 RTS1 CTS0 (Note) P64 Pin Functions Bit set value U1C0 register CRS CRD 1 0 0 0 0 1 0 UCON register RCSP CLKMD1 0 0 0 1 0 0 0 0 PD6 register PD6_4 Input: 0, Output: 1 0 0 Note: In addition to this, set the U0C0 register's CRD bit to "0" (CTS0/RTS0 enabled) and the U0C0 register's CRS bit to "1" (RTS0 selected). Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 111 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O (1) Example of transmit timing when transfer data is 8 bits long (parity enabled, one stop bit) Tc Transfer clock UiC1 register TE bit UiC1 register TI bit "1" "0" "1" "0" The transfer clock stops momentarily as CTSi is "H" when the stop bit is checked. The transfer clock starts as the transfer starts immediately CTSi changes to "L". Write data to the UiTB register Transferred from UiTB register to UARTi transmit register "H" CTSi "L" Start bit TxDi UiC0 register TXEPT bit SiTIC register IR bit "1" "0" "1" "0" Parity Stop bit bit P SP ST D0 D1 D2 D3 D4 D5 D6 D7 P SP Stopped pulsing because the TE bit = "0" ST D0 D1 ST D0 D1 D2 D3 D4 D5 D6 D7 Cleared to "0" when interrupt request is accepted, or cleared to "0" in a program The above timing diagram applies to the case where the register bits are set as follows: * UiMR register PRYE bit = 1 (parity enabled) * UiMR register STPS bit = 0 (1 stop bit) * UiC0 register CRD bit = 0 (CTS/RTS enabled), CRS bit = 0 (CTS selected) * UiRS bit = 1 (an interrupt request occurs when transmit completed): U0IRS bit is the UCON register bit 0, U1IRS bit is the UCON register bit 1, and U2IRS bit is the U2C1 register bit 4 Tc = 16 (n + 1) / fj or 16 (n + 1) / fEXT fj : frequency of UiBRG count source (f1SIO, f2SIO, f8SIO, f32SIO) fEXT : frequency of UiBRG count source (external clock) n : value set to UiBRG i: 0 to 2 (2) Example of transmit timing when transfer data is 9 bits long (parity disabled, two stop bits) Tc Transfer clock UiC1 register TE bit UiC1 register TI bit "1" "0" "1" "0" Write data to the UiTB register Start bit TxDi UiC0 register TXEPT bit SiTIC register IR bit "1" "0" "1" "0" Stop Stop bit bit Transferred from UiTB register to UARTi transmit register ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SP SP ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SPSP ST D0 D1 Cleared to "0" when interrupt request is accepted, or cleared to "0" in a program Tc = 16 (n + 1) / fj or 16 (n + 1) / fEXT The above timing diagram applies to the case where the register bits are set as follows: fj : frequency of UiBRG count source (f1SIO, f2SIO, f8SIO, f32SIO) * UiMR register PRYE bit = 0 (parity disabled) fEXT : frequency of UiBRG count source (external clock) * UiMR register STPS bit = 1 (2 stop bits) n : value set to UiBRG * UiC0 register CRD bit = 1 (CTS/RTS disabled) i: 0 to 2 * UiRS bit = 0 (an interrupt request occurs when transmit buffer becomes empty): U0IRS bit is the UCON register bit 0, U1IRS bit is the UCON register bit 1, and U2IRS bit is the U2C1 register bit 4 Figure 10.15 Transmit Operation Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 112 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O * Example of receive timing when transfer data is 8 bits long (parity disabled, one stop bit) UiBRG count source UiC1 register RE bit RxDi "1" "0" Start bit Sampled "L" Receive data taken in Transfer clock UiC1 register RI bit RTSi SiRIC register IR bit Reception triggered when transfer clock "1" is generated by falling edge of start bit "0" "H" "L" "1" "0" Cleared to "0" when interrupt request is accepted, or cleared to "0" in a program The above timing diagram applies to the case where the register bits are set as follows: * UiMR register PRYE bit = 0 (parity disabled) * UiMR register STPS bit = 0 (1 stop bit) * UiC0 register CRD bit = 0 (CTSi/RTSi enabled), CRS bit = 1 (RTSi selected) i = 0 to 2 Transferred from UARTi receive register to UiRB register Stop bit D0 D1 D7 Figure 10.16 Receive Operation 10.3.1 LSB First/MSB First Select Function As shown in Figure 10.17, use the UiC0 register's UFORM bit to select the transfer format. This function is valid when transfer data is 8 bits long. (1) When UiC0 register's UFORM bit = 0 (LSB first) CLKi TXDi RXDi ST ST D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7 P P SP SP (2) When UiC0 register's UFORM bit = 1 (MSB first) CLKi TXDi RXDi ST ST D7 D7 D6 D6 D5 D5 D4 D4 D3 D3 D2 D2 D1 D1 D0 D0 P P SP SP ST : Start bit P : Parity bit SP : Stop bit i = 0 to 2 Note: This applies to the case where the UiC0 register's CKPOL bit = 0 ( transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock), the UiC1 register's UiLCH bit = 0 (no reverse), UiMR register's STPS bit = 0 (1 stop bit) and UiMR register's PRYE bit = 1 (parity enabled). Figure 10.17 Transfer Format Page 113 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.3.2 Serial Data Logic Switching Function The data written to the UiTB register has its logic reversed before being transmitted. Similarly, the received data has its logic reversed when read from the UiRB register. Figure 10.18 shows serial data logic. (1) When the UiC1 register's UiLCH bit = 0 (no reverse) Transfer clock TxDi (no reverse) "H" "L" "H" "L" ST D0 D1 D2 D3 D4 D5 D6 D7 P SP (2) When the UiC1 register's UiLCH bit = 1 (reverse) Transfer clock TxDi (reverse) "H" "L" "H" "L" ST D0 D1 D2 D3 D4 D5 D6 D7 P SP ST : Start bit P : Parity bit SP : Stop bit i = 0 to 2 Note: This applies to the case where the UiC0 register's CKPOL bit = 0 (transmit data output at the falling edge of the transfer clock), the UiC0 register's UFORM bit = 0 (LSB first), the UiMR register's STPS bit = 0 (1 stop bit) and UiMR register's PRYE bit = 1 (parity enabled). Figure 10.18 Serial Data Logic Switching 10.3.3 TxD and RxD I/O Polarity Inverse Function This function inverses the polarities of the TXDi pin output and RXDi pin input. The logic levels of all input/ output data (including the start, stop and parity bits) are inversed. Figure 10.19 shows the TXD pin output and RXD pin input polarity inverse. (1) When the UiMR register's IOPOL bit = 0 (no reverse) Transfer clock TxDi RxDi "H" "L" "H" (no reverse) "L" "H" ST ST D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7 P P SP SP (no reverse) "L" (2) When the UiMR register's IOPOL bit = 1 (reverse) Transfer clock TxDi (reverse) "H" "L" "H" "L" "H" "L" ST ST D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7 P P SP SP RxDi (reverse) ST : Start bit P : Parity bit SP : Stop bit i = 0 to 2 Note: This applies to the case where the UiC0 register's UFORM bit = 0 (LSB first), the UiMR register's STPS bit = 0 (1 stop bit) and the UiMR register's PRYE bit = 1 (parity enabled). Figure 10.19 TXD and RXD I/O Polarity Inverse Page 114 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.3.4 CTS/RTS Separate Function (UART0) This function separates CTS0/RTS0, outputs RTS0 from the P60 pin, and accepts as input the CTS0 from the P64 pin. To use this function, set the register bits as shown below. * U0C0 register's CRD bit = 0 (enables UART0 CTS/RTS) * U0C0 register's CRS bit = 1 (outputs UART0 RTS) * U1C0 register's CRD bit = 0 (enables UART1 CTS/RTS) * U1C0 register's CRS bit = 0 (inputs UART1 CTS) * UCON register's RCSP bit = 1 (inputs CTS0 from the P64 pin) * UCON register's CLKMD1 bit = 0 (CLKS1 not used) Note that when using the CTS/RTS separate function, UART1 CTS/RTS function cannot be used. Microcomputer TXD0 (P63) RXD0 (P62) IN OUT IC RTS0 (P60) CTS0 (P64) CTS RTS Figure 10.20 CTS/RTS Separate Function Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 115 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.4 Special Mode 1 (I2C mode) I2C mode is provided for use as a simplified I2C interface compatible mode. Table 10.9 lists the specifications of the I2C mode. Table 10.10 to 10.11 lists the registers used in the I2C mode and the register values set, Table 10.12 lists the I2C mode functions. Figure 10.21 shows the block diagram for I2C mode. Figure 10.22 shows SCLi timing. As shown in Table 10.12, the microcomputer is placed in I2C mode by setting the SMD2 to SMD0 bits to `0102' and the IICM bit to "1". Because SDAi transmit output has a delay circuit attached, SDAi output does not change state until SCLi goes low and remains stably low. Table 10.9 I2C Mode Specifications Item Transfer data format Transfer clock * Transfer data length: 8 bits * During master UiMR(i=0 to 2) register's CKDIR bit = "0" (internal clock) : fj/ 2(n+1) fj = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of UiBRG register 0016 to FF16 * During slave Transmission start condition CKDIR bit = "1" (external clock) : Input from SCLi pin * Before transmission can start, the following requirements must be met (Note 1) _ _ Specification The TE bit of UiC1 register= 1 (transmission enabled) Reception start condition The TI bit of UiC1 register = 0 (data present in UiTB register) * Before reception can start, the following requirements must be met (Note 1) _ The RE bit of UiC1 register= 1 (reception enabled) _ _ The TE bit of UiC1 register= 1 (transmission enabled) Interrupt request generation timing Error detection The TI bit of UiC1 register= 0 (data present in the UiTB register) When start or stop condition is detected, acknowledge undetected, and acknowledge detected * Overrun error (Note 2) This error occurs if the serial I/O started receiving the next data before reading the UiRB register and received the 8th bit of the next data * Arbitration lost Timing at which the UiRB register's ABT bit is updated can be selected * SDAi digital delay No digital delay or a delay of 2 to 8 UiBRG count source clock cycles selectable * Clock phase setting With or without clock delay selectable Select function Note 1: When an external clock is selected, the conditions must be met while the external clock is in the high state. Note 2: If an overrun error occurs, the value of UiRB register will be indeterminate. The IR bit of SiRIC register does not change. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 116 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O SDAi Delay circuit Start and stop condition generation block STSPSEL=1 STSPSEL=0 ACK=0 SDHI ACKD register D Q SDASTSP SCLSTSP IICM2=1 DMA0, DMA1 request (UART1: DMA0 only) ACK=1 Transmission register UARTi ALS IICM=1 and IICM2=0 UARTi transmit, NACK interrupt request Arbitration IICM2=1 Noise Filter T DMA0 (UART0, UART2) Reception register UARTi Start condition detection IICM=1 and IICM2=0 S R Q UARTi receive, ACK interrupt request, DMA1 request Bus busy NACK Stop condition detection D Q SCLi Falling edge detection IICM=0 I/O port Q R T DQ T STSPSEL=0 IICM=1 UARTi Noise Filter Port register (Note) Internal clock CLK control ACK 9th bit SWC2 STSPSEL=1 External clock R S Start/stop condition detection interrupt request UARTi 9th bit falling edge SWC This diagram applies to the case where the UiMR register's SMD2 to SMD0 bits = 0102 and the UiSMR register's IICM bit = 1. IICM : UiSMR register bit IICM2, SWC, ALS, SWC2, SDHI : UiSMR2 register bit STSPSEL, ACKD, ACKC : UiSMR4 register bit i=0 to 2 Note: If the IICM bit = 1, the pin can be read even when the PD6_2, PD6_6 or PD7_1 bit = 1 (output mode). Figure 10.21 I2C Mode Block Diagram Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 117 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 10.10 Register 10. SERIAL I/O Registers to Be Used and Settings in I2C Mode (1) (Continued) Bit Function Master Set transmission data Slave Set transmission data Reception data can be read ACK or NACK is set in this bit Invalid Overrun error flag Invalid Set to `0102' Set to "1" Set to "0" Invalid Invalid because CRD = 1 Transmit buffer empty flag Set to "1" Set to "1" (Note 2) Set to "0" Set to "1" Set this bit to "1" to enable transmission Transmit buffer empty flag Set this bit to "1" to enable reception Reception complete flag Invalid Set to "0" Set to "1" Invalid Bus busy flag Set to "0" Refer to Table 11.12 Set to "0" Set this bit to "1" to have SCLi output fixed to "L" at the falling edge of the 9th bit of clock Set to "0" Set this bit to "1" to initialize UARTi at start condition detection Set this bit to "1" to have SCLi output forcibly pulled low Set this bit to "1" to disable SDAi output Set to "0" Set to "0" Refer to Table 11.12 Set the amount of SDAi digital delay UiTB 0 to 7 (Note 3) UiRB 0 to 7 (Note 3) 8 ABT OER UiBRG 0 to 7 UiMR SMD2 to SMD0 (Note 3) CKDIR IOPOL UiC0 CLK1, CLK0 Reception data can be read ACK or NACK is set in this bit Arbitration lost detection flag Overrun error flag Set a transfer rate Set to `0102' Set to "0" Set to "0" Select the count source for the UiBRG register CRS Invalid because CRD = 1 TXEPT Transmit buffer empty flag CRD Set to "1" NCH Set to "1" (Note 2) CKPOL Set to "0" UFORM Set to "1" UiC1 TE Set this bit to "1" to enable transmission TI Transmit buffer empty flag RE Set this bit to "1" to enable reception RI Reception complete flag U2IRS (Note 1) Invalid U2RRM (Note 1), Set to "0" UiLCH, UiERE UiSMR IICM Set to "1" ABC Select the timing at which arbitration-lost is detected BBS Bus busy flag 3 to 7 Set to "0" UiSMR2 IICM2 Refer to Table 11.12 CSC Set this bit to "1" to enable clock synchronization SWC Set this bit to "1" to have SCLi output fixed to "L" at the falling edge of the 9th bit of clock ALS Set this bit to "1" to have SDAi output stopped when arbitration-lost is detected STAC Set to "0" Set this bit to "1" to have SCLi output forcibly pulled low SDHI Set this bit to "1" to disable SDAi output 7 Set to "0" UiSMR3 0, 2, 4 and NODC Set to "0" CKPH Refer to Table 11.12 DL2 to DL0 Set the amount of SDAi digital delay SWC2 i=0 to 2 Notes: 1. Set the U0C1 and U1C1 register bit 4 and bit 5 to "0". The U0IRS, U1IRS, U0RRM and U1RRM bits are in the UCON register. 2. TxD2 pin is N channel open-drain output. Set the NCH bit in the U2C0 register to "0". 3. Not all register bits are described above. Set those bits to "0" when writing to the registers in I2C mode. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 118 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 10.11 Register 10. SERIAL I/O Registers to Be Used and Settings in I2C Mode (2) (Continued) Bit Function Master Slave Set this bit to "1" to generate start Set to "0" condition Set this bit to "1" to generate restart Set to "0" condition Set this bit to "1" to generate stop Set to "0" condition Set this bit to "1" to output each condition Set to "0" Select ACK or NACK Select ACK or NACK Set this bit to "1" to output ACK data Set this bit to "1" to output ACK data Set this bit to "1" to have SCLi output Set to "0" stopped when stop condition is detected Set to "0" Set this bit to "1" to set the SCLi to "L" hold at the next falling edge of the 9th bit of clock Set to "1" Set to "1" Invalid Invalid Set to "0" Set to "0" UiSMR4 STAREQ RSTAREQ STPREQ STSPSEL ACKD ACKC SCLHI SWC9 IFSR2A IFSR26, ISFR27 UCON U0IRS, U1IRS 2 to 7 i=0 to 2 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 119 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 10.12 Function 10. SERIAL I/O I2C Mode Functions Clock synchronous serial I/O I2C mode (SMD2 to SMD0 = 0102, IICM = 1) mode (SMD2 to SMD0 = 0012, IICM2 = 0 IICM2 = 1 IICM = 0) (NACK/ACK interrupt) (UART transmit/ receive interrupt) CKPH = 1 CKPH = 1 CKPH = 0 CKPH = 0 (Clock delay) (No clock delay) (Clock delay) (No clock delay) Start condition detection or stop condition detection (Refer to "Table 10.13. STSPSEL Bit Functions") No acknowledgment detection (NACK) Rising edge of SCLi 9th bit Acknowledgment detection (ACK) Rising edge of SCLi 9th bit Rising edge of SCLi 9th bit UARTi transmission UARTi transmission Falling edge of SCLi Rising edge of next to the 9th bit SCLi 9th bit UARTi reception Falling edge of SCLi 9th bit Factor of interrupt number 6, 7 and 10 (Note 1, 5, 7) Factor of interrupt number UARTi transmission 15, 17 and 19 (Note 1, 6) Transmission started or completed (selected by UiIRS) Factor of interrupt number UARTi reception 16, 18 and 20 (Note 1, 6) When 8th bit received CKPOL = 0 (rising edge) CKPOL = 1 (falling edge) Timing for transferring data CKPOL = 0 (rising edge) from the UART reception CKPOL = 1 (falling edge) shift register to the UiRB register UARTi transmission output Not delayed delay Functions of P63, P67 and TxDi output P70 pins Functions of P62, P66 and RxDi input P71 pins Functions of P61, P65 and P72 pins Noise filter width Read RxDi and SCLi pin levels Initial value of TxDi and SDAi outputs Initial and end values of SCLi DMA1 factor (Refer to Fig 10.22) Store received data UARTi reception 1st to 8th bits are stored in UiRB register bit 0 to bit 7 CLKi input or output selected 15ns Falling edge of SCLi 9th bit Falling and rising edges of SCLi 9th bit Delayed SDAi input/output SCLi input/output (Cannot be used in I2C mode) 200ns Always possible no matter how the corresponding port direction bit is set Possible when the corresponding port direction bit =0 CKPOL = 0 (H) The value set in the port register before setting I2C mode (Note 2) CKPOL = 1 (L) H L H L Acknowledgment detection (ACK) 1st to 8th bits are stored in UiRB register bit 7 to bit 0 UARTi reception Falling edge of SCLi 9th bit 1st to 7th bits are stored in UiRB register bit 6 to bit 0, with 8th bit stored in UiRB register bit 8 1st to 8th bits are stored in UiRB register bit 7 to bit 0 (Note 3) Read UiRB register Bit 6 to bit 0 as bit 7 to bit 1, and bit 8 as bit 0 (Note 4) Read received data UiRB register status is read directly as is i = 0 to 2 Note 1: If the source or cause of any interrupt is changed, the IR bit in the interrupt control register for the changed interrupt may inadvertently be set to "1" (interrupt requested). (Refer to "precautions for interrupts" of the Usage Notes Reference Book.) If one of the bits shown below is changed, the interrupt source, the interrupt timing, etc. change. Therefore, always be sure to clear the IR bit to "0" (interrupt not requested) after changing those bits. SMD2 to SMD0 bits in the UiMR register, IICM bit in the UiSMR register, IICM2 bit in the UiSMR2 register, CKPH bit in the UiSMR3 register Note 2: Set the initial value of SDAi output while the UiMR register's SMD2 to SMD0 bits = `0002' (serial I/O disabled). Note 3: Second data transfer to UiRB register (Rising edge of SCLi 9th bit) Note 4: First data transfer to UiRB register (Falling edge of SCLi 9th bit) Note 5: Refer to "Figure 10.13. STSPSEL Bit Functions". Note 6: Refer to "Figure 10.22. Transfer to UiRB Register and Interrupt Timing" . Note 7: When using UART0, be sure to set the IFSR26 bit in the IFSR2A register to "1" (cause of interrupt: UART0 bus collision). When using UART1, be sure to set the IFSR27 bit in the IFSR2A register to "1" (cause of interrupt: UART1 bus collision). Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 120 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O (1) IICM2= 0 (ACK and NACK interrupts), CKPH= 0 (no clock delay) 1st bit 2nd bit 3rd bit 4th bit 5th bit 6th bit 7th bit 8th bit 9th bit SCLi SDAi D7 D6 D5 D4 D3 D2 D1 D0 D8 (ACK, NACK) ACK interrupt (DMA1 request), NACK interrupt Transfer to UiRB register b15 *** b9 b8 D8 b7 D7 D6 D5 D4 D3 D2 D1 b0 D0 UiRB register (2) IICM2= 0, CKPH= 1 (clock delay) 1st bit 2nd bit 3rd bit 4th bit 5th bit 6th bit 7th bit 8th bit 9th bit SCLi SDAi D7 D6 D5 D4 D3 D2 D1 D0 D8 (ACK, NACK) ACK interrupt (DMA1 request), NACK interrupt Transfer to UiRB register b15 *** b9 b8 D8 b7 D7 D6 D5 D4 D3 D2 D1 b0 D0 UiRB register (3) IICM2= 1 (UART transmit/receive interrupt), CKPH= 0 1st bit 2nd bit 3rd bit 4th bit 5th bit 6th bit 7th bit 8th bit 9th bit SCLi SDAi D7 D6 D5 D4 D3 D2 D1 D0 D8 (ACK, NACK) Transmit interrupt Receive interrupt (DMA1 request) Transfer to UiRB register b15 *** b9 b8 D0 b7 D7 D6 D5 D4 D3 D2 b0 D1 UiRB register (4) IICM2= 1, CKPH= 1 1st bit 2nd bit 3rd bit 4th bit 5th bit 6th bit 7th bit 8th bit 9th bit SCLi SDAi D7 D6 D5 D4 D3 D2 D1 D0 D8 (ACK, NACK) Transmit interrupt Receive interrupt (DMA1 request) Transfer to UiRB register b15 *** b9 b8 D0 b7 D7 D6 D5 D4 D3 D2 b0 D1 Transfer to UiRB register b15 *** b9 b8 D8 b7 D7 D6 D5 D4 D3 D2 D1 b0 D0 i=0 to 2 UiRB register UiRB register This diagram applies to the case where the following condition is met. * UiMR register CKDIR bit = 0 (Slave selected) Figure 10.22 Transfer to UiRB Register and Interrupt Timing Page 121 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.4.1 Detection of Start and Stop Condtion Whether a start or a stop condition has been detected is determined. A start condition-detected interrupt request is generated when the SDAi pin changes state from high to low while the SCLi pin is in the high state. A stop condition-detected interrupt request is generated when the SDAi pin changes state from low to high while the SCLi pin is in the high state. Because the start and stop condition-detected interrupts share the interrupt control register and vector, check the UiSMR register's BBS bit to determine which interrupt source is requesting the interrupt. 3 to 6 cycles < duration for setting-up (Note) 3 to 6 cycles < duration for holding (Note) Duration for setting up SCLi SDAi Duration for holding (Start condition) SDA i (Stop condition) i = 0 to 2 Note: When the PCLKR register's PCLK1 bit = 1, this is the cycle number of f1SIO, and the PCLK1 bit = 0, this is the cycle number of f2SIO. Figure 10.23 Detection of Start and Stop Condition 10.4.2 Output of Start and Stop Condition A start condition is generated by setting the UiSMR4 register (i = 0 to 2)'s STAREQ bit to "1" (start). A restart condition is generated by setting the UiSMR4 register's RSTAREQ bit to "1" (start). A stop condition is generated by setting the UiSMR4 register's STPREQ bit to "1" (start). The output procedure is described below. Set the STAREQ bit, RSTAREQ bit or STPREQ bit to "1" (start). Set the STSPSEL bit in the UiSMR4 register to "1" (output). The function of the STSPSEL bit is shown in Table 10.13 and Figure 10.24. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 122 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 10.13 STSPSEL Bit Functions STSPSEL = 0 Output of transfer clock and data Output of start/stop condition is accomplished by a program using ports (not automatically Start/stop condition interrupt request generation timing generated in hardware) Start/stop condition detection 10. SERIAL I/O Function Output of SCLi and SDAi pins STSPSEL = 1 Output of a start/stop condition according to the STAREQ, RSTAREQ and STPREQ bit Finish generating start/stop condition (1) When slave CKDIR=1 (external clock) STSPSEL bit 0 1st 2nd 3rd 5th 6th 7th 8th 9th bit SCLi SDAi Start condition detection interrupt Stop condition detection interrupt (2) When master CKDIR=0 (internal clock), CKPH=1 (clock delayed) STSPSEL bit Set to "1" in a program Set to "0" in a program 1st 2nd 3rd Set to "1" in a program 5th 6th 7th 8th 9th bit Set to "0" in a program SCLi SDAi Set STAREQ= 1 (start) Start condition detection interrupt Set STPREQ= 1 (start) Stop condition detection interrupt Figure 10.24 STSPSEL Bit Functions 10.4.3 Arbitration Unmatching of the transmit data and SDAi pin input data is checked synchronously with the rising edge of SCLi. Use the UiSMR register's ABC bit to select the timing at which the UiRB register's ABT bit is updated. If the ABC bit = 0 (updated bitwise), the ABT bit is set to "1" at the same time unmatching is detected during check, and is cleared to "0" when not detected. In cases when the ABC bit is set to "1", if unmatching is detected even once during check, the ABT bit is set to "1" (unmatching detected) at the falling edge of the clock pulse of 9th bit. If the ABT bit needs to be updated bytewise, clear the ABT bit to "0" (undetected) after detecting acknowledge in the first byte, before transferring the next byte. Setting the UiSMR2 register's ALS bit to "1" (SDA output stop enabled) causes arbitration-lost to occur, in which case the SDAi pin is placed in the high-impedance state at the same time the ABT bit is set to "1" (unmatching detected). Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 123 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.4.4 Transfer Clock Data is transmitted/received using a transfer clock like the one shown in Figure 10.24. The UiSMR2 register's CSC bit is used to synchronize the internally generated clock (internal SCLi) and an external clock supplied to the SCLi pin. In cases when the CSC bit is set to "1" (clock synchronization enabled), if a falling edge on the SCLi pin is detected while the internal SCLi is high, the internal SCLi goes low, at which time the UiBRG register value is reloaded with and starts counting in the low-level interval. If the internal SCLi changes state from low to high while the SCLi pin is low, counting stops, and when the SCLi pin goes high, counting restarts. In this way, the UARTi transfer clock is comprised of the logical product of the internal SCLi and SCLi pin signal. The transfer clock works from a half period before the falling edge of the internal SCLi 1st bit to the rising edge of the 9th bit. To use this function, select an internal clock for the transfer clock. The UiSMR2 register's SWC bit allows to select whether the SCLi pin should be fixed to or freed from lowlevel output at the falling edge of the 9th clock pulse. If the UiSMR4 register's SCLHI bit is set to "1" (enabled), SCLi output is turned off (placed in the high impedance state) when a stop condition is detected. Setting the UiSMR2 register's SWC2 bit = 1 (0 output) makes it possible to forcibly output a low-level signal from the SCLi pin even while sending or receiving data. Clearing the SWC2 bit to "0" (transfer clock) allows the transfer clock to be output from or supplied to the SCLi pin, instead of outputting a low-level signal. If the UiSMR4 register's SWC9 bit is set to "1" (SCL hold low enabled) when the UiSMR3 register's CKPH bit = 1, the SCLi pin is fixed to low-level output at the falling edge of the clock pulse next to the ninth. Setting the SWC9 bit = 0 (SCL hold low disabled) frees the SCLi pin from low-level output. 10.4.5 SDA Output The data written to the UiTB register bit 7 to bit 0 (D7 to D0) is sequentially output beginning with D7. The ninth bit (D8) is ACK or NACK. The initial value of SDAi transmit output can only be set when IICM = 1 (I2C mode) and the UiMR register's SMD2 to SMD0 bits = `0002' (serial I/O disabled). The UiSMR3 register's DL2 to DL0 bits allow to add no delays or a delay of 2 to 8 UiBRG count source clock cycles to SDAi output. Setting the UiSMR2 register's SDHI bit = 1 (SDA output disabled) forcibly places the SDAi pin in the highimpedance state. Do not write to the SDHI bit synchronously with the rising edge of the UARTi transfer clock. This is because the ABT bit may inadvertently be set to "1" (detected). 10.4.6 SDA Input When the IICM2 bit = 0, the 1st to 8th bits (D7 to D0) of received data are stored in the UiRB register bit 7 to bit 0. The 9th bit (D8) is ACK or NACK. When the IICM2 bit = 1, the 1st to 7th bits (D7 to D1) of received data are stored in the UiRB register bit 6 to bit 0 and the 8th bit (D0) is stored in the UiRB register bit 8. Even when the IICM2 bit = 1, providing the CKPH bit = 1, the same data as when the IICM2 bit = 0 can be read out by reading the UiRB register after the rising edge of the corresponding clock pulse of 9th bit. 10.4.7 ACK and NACK If the STSPSEL bit in the UiSMR4 register is set to "0" (start and stop conditions not generated) and the ACKC bit in the UiSMR4 register is se to "1" (ACK data output), the value of the ACKD bit in the UiSMR4 register is output from the SDAi pin. If the IICM2 bit = 0, a NACK interrupt request is generated if the SDAi pin remains high at the rising edge of the 9th bit of transmit clock pulse. An ACK interrupt request is generated if the SDAi pin is low at the rising edge of the 9th bit of transmit clock pulse. If ACKi is selected for the cause of DMA1 request, a DMA transfer can be activated by detection of an acknowledge. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 124 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.4.8 Initialization of Transmission/Reception If a start condition is detected while the STAC bit = 1 (UARTi initialization enabled), the serial I/O operates as described below. The transmit shift register is initialized, and the content of the UiTB register is transferred to the transmit shift register. In this way, the serial I/O starts sending data synchronously with the next clock pulse applied. However, the UARTi output value does not change state and remains the same as when a start condition was detected until the first bit of data is output synchronously with the input clock. The receive shift register is initialized, and the serial I/O starts receiving data synchronously with the next clock pulse applied. The SWC bit is set to "1" (SCL wait output enabled). Consequently, the SCLi pin is pulled low at the falling edge of the ninth clock pulse. Note that when UARTi transmission/reception is started using this function, the TI does not change state. Note also that when using this function, the selected transfer clock should be an external clock. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 125 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.5 Special Mode 2 Multiple slaves can be serially communicated from one master. Transfer clock polarity and phase are selectable. Table 10.14 lists the specifications of Special Mode 2. Table 10.15 lists the registers used in Special Mode 2 and the register values set. Figure 10.25 shows communication control example for Special Mode 2. Table 10.14 Special Mode 2 Specifications Specification * Transfer data length: 8 bits * Master mode UiMR(i=0 to 2) register's CKDIR bit = "0" (internal clock) : fj/ 2(n+1) fj = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of UiBRG register 0016 to FF16 * Slave mode CKDIR bit = "1" (external clock selected) : Input from CLKi pin Controlled by input/output ports * Before transmission can start, the following requirements must be met (Note 1) _ The TE bit of UiC1 register= 1 (transmission enabled) _ The TI bit of UiC1 register = 0 (data present in UiTB register) * Before reception can start, the following requirements must be met (Note 1) _ The RE bit of UiC1 register= 1 (reception enabled) The TE bit of UiC1 register= 1 (transmission enabled) The TI bit of UiC1 register= 0 (data present in the UiTB register) * For transmission, one of the following conditions can be selected _ The UiIRS bit of UiC1 register = 0 (transmit buffer empty): when transferring data from the UiTB register to the UARTi transmit register (at start of transmission) _ The UiIRS bit =1 (transfer completed): when the serial I/O finished sending data from the UARTi transmit register * For reception When transferring data from the UARTi receive register to the UiRB register (at completion of reception) * Overrun error (Note 2) This error occurs if the serial I/O started receiving the next data before reading the UiRB register and received the 7th bit of the next data * Clock phase setting Selectable from four combinations of transfer clock polarities and phases _ _ Item Transfer data format Transfer clock Transmit/receive control Transmission start condition Reception start condition Interrupt request generation timing Error detection Select function Note 1: When an external clock is selected, the conditions must be met while if the UiC0 register's CKPOL bit = "0" (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock), the external clock is in the high state; if the UiC0 register's CKPOL bit = "1" (transmit data output at the rising edge and the receive data taken in at the falling edge of the transfer clock), the external clock is in the low state. Note 2: If an overrun error occurs, the value of UiRB register will be indeterminate. The IR bit of SiRIC register does not change. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 126 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O P13 P12 P93 P72(CLK2) P71(RxD2) P70(TxD2) Microcomputer (Master) P72(CLK2) P71(RxD2) P70(TxD2) Microcomputer (Slave) P93 P72(CLK2) P71(RxD2) P70(TxD2) Microcomputer (Slave) Figure 10.25 Serial Bus Communication Control Example (UART2) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 127 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 10.15 Registers to Be Used and Settings in Special Mode 2 10. SERIAL I/O Register Bit UiTB(Note3) 0 to 7 UiRB(Note3) 0 to 7 OER UiBRG 0 to 7 UiMR(Note3) SMD2 to SMD0 CKDIR IOPOL UiC0 CLK1, CLK0 CRS TXEPT CRD NCH CKPOL UFORM UiC1 TE TI RE RI U2IRS (Note 1) U2RRM(Note 1), U2LCH, UiERE UiSMR 0 to 7 UiSMR2 0 to 7 UiSMR3 CKPH NODC 0, 2, 4 to 7 UiSMR4 0 to 7 UCON U0IRS, U1IRS U0RRM, U1RRM CLKMD0 CLKMD1, RCSP, 7 Function Set transmission data Reception data can be read Overrun error flag Set a transfer rate Set to `0012' Set this bit to "0" for master mode or "1" for slave mode Set to "0" Select the count source for the UiBRG register Invalid because CRD = 1 Transmit register empty flag Set to "1" Select TxDi pin output format(Note 2) Clock phases can be set in combination with the UiSMR3 register's CKPH bit Set to "0" Set this bit to "1" to enable transmission Transmit buffer empty flag Set this bit to "1" to enable reception Reception complete flag Select UART2 transmit interrupt cause Set to "0" Set to "0" Set to "0" Clock phases can be set in combination with the UiC0 register's CKPOL bit Set to "0" Set to "0" Set to "0" Select UART0 and UART1 transmit interrupt cause Set to "0" Invalid because CLKMD1 = 0 Set to "0" Note 1: Set the U0C0 and U1C1 register bit 4 and bit 5 to "0". The U0IRS, U1IRS, U0RRM and U1RRM bits are in the UCON register. Note 2: TxD2 pin is N channel open-drain output. Set the U2C0 register's NCH bit to "0". Note 3: Not all register bits are described above. Set those bits to "0" when writing to the registers in Special Mode 2. i = 0 to 2 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 128 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.5.1 Clock Phase Setting Function One of four combinations of transfer clock phases and polarities can be selected using the UiSMR3 register's CKPH bit and the UiC0 register's CKPOL bit. Make sure the transfer clock polarity and phase are the same for the master and salves to be communicated. * Master (Internal Clock) Figure 10.26 shows the transmission and reception timing in master (internal clock). * Slave (External Clock) Figure 10.27 shows the transmission and reception timing (CKPH=0) in slave (external clock) while Figure 10.28 shows the transmission and reception timing (CKPH=1) in slave (external clock). "H" Clock output (CKPOL=0, CKPH=0) "L" "H" Clock output (CKPOL=1, CKPH=0) "L" Clock output "H" (CKPOL=0, CKPH=1) "L" "H" Clock output (CKPOL=1, CKPH=1) "L" Data output timing "H" "L" D0 D1 D2 D3 D4 D5 D6 D7 Data input timing Figure 10.26 Transmission and Reception Timing in Master Mode (Internal Clock) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 129 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O "H" Slave control input "L" "H" Clock input (CKPOL=0, CKPH=0) "L" "H" Clock input (CKPOL=1, CKPH=0) "L" Data output timing (Note) Data input timing "H" "L" D0 D1 D2 D3 D4 D5 D6 D7 Indeterminate Note :UART2 output is an N-channel open drain and must be pulled-up externally. Figure 10.27 Transmission and Reception Timing (CKPH=0) in Slave Mode (External Clock) "H" Slave control input "L" "H" Clock input (CKPOL=0, CKPH=1) "L" "H" Clock input (CKPOL=1, CKPH=1) "L" Data output timing (Note) Data input timing "H" "L" D0 D1 D2 D3 D4 D5 D6 D7 Note :UART2 output is an N-channel open drain and must be pulled-up externally. Figure 10.28 Transmission and Reception Timing (CKPH=1) in Slave Mode (External Clock) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 130 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.6 Special Mode 3 (IE mode) In this mode, one bit of IEBus is approximated with one byte of UART mode waveform. Table 10.16 lists the registers used in IE mode and the register values set. Figure 10.29 shows the functions of bus collision detect function related bits. If the TxDi pin (i = 0 to 2) output level and RxDi pin input level do not match, a UARTi bus collision detect interrupt request is generated. Use the IFSR2A register's IFSR26 and IFSR27 bits to enable the UART0/UART1 bus collision detect function. Table 10.16 Registers to Be Used and Settings in IE Mode Function Set transmission data Reception data can be read Error flag Set a transfer rate Set to `1102' Select the internal clock or external clock Set to "0" Invalid because PRYE=0 Set to "0" Select the TxD/RxD input/output polarity Select the count source for the UiBRG register Invalid because CRD=1 Transmit register empty flag Set to "1" Select TxDi pin output mode (Note 2) Set to "0" Set to "0" Set this bit to "1" to enable transmission Transmit buffer empty flag Set this bit to "1" to enable reception Reception complete flag Select the source of UART2 transmit interrupt Set to "0" Set to "0" Select the sampling timing at which to detect a bus collision Set this bit to "1" to use the auto clear function of transmit enable bit Select the transmit start condition Set to "0" Set to "0" Set to "0" Set to "1" Select the source of UART0/UART1 transmit interrupt Set to "0" Invalid because CLKMD1 = 0 Set to "0" Register Bit UiTB 0 to 8 UiRB(Note3) 0 to 8 OER,FER,PER,SUM UiBRG 0 to 7 UiMR SMD2 to SMD0 CKDIR STPS PRY PRYE IOPOL UiC0 CLK1, CLK0 CRS TXEPT CRD NCH CKPOL UFORM UiC1 TE TI RE RI U2IRS (Note 1) UiRRM (Note 1), UiLCH, UiERE UiSMR 0 to 3, 7 ABSCS ACSE SSS UiSMR2 0 to 7 UiSMR3 0 to 7 UiSMR4 0 to 7 IFSR2A IFSR26, IFSR27 UCON U0IRS, U1IRS U0RRM, U1RRM CLKMD0 CLKMD1,RCSP,7 Note 1: Set the U0C0 and U1C1 registers bit 4 and bit 5 to "0". The U0IRS, U1IRS, U0RRM and U1RRM bits are in the UCON register. Note 2: TxD2 pin is N channel open-drain output. Set the U2C0 register's NCH bit to "0". Note 3: Not all register bits are described above. Set those bits to "0" when writing to the registers in IEmode. i= 0 to 2 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 131 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O (1) UiSMR register ABSCS bit (bus collision detect sampling clock select) If ABSCS=0, bus collision is determined at the rising edge of the transfer clock (i=0 to 2) Transfer clock ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SP TxDi RxDi Input to TAjIN Timer Aj If ABSCS=1, bus collision is determined when timer Aj (one-shot timer mode) underflows. Timer Aj: timer A3 when UART0; timer A4 when UART1; timer A0 when UART2 (2) UiSMR register ACSE bit (auto clear of transmit enable bit) Transfer clock ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SP TxDi RxDi UiBCNIC register IR bit (Note) UiC1 register TE bit Note: BCNIC register when UART2. If ACSE bit = 1 (automatically clear when bus collision occurs), the TE bit is cleared to "0" (transmission disabled) when the UiBCNIC register's IR bit = 1 (unmatching detected). (3) UiSMR register SSS bit (Transmit start condition select ) If SSS bit = 0, the serial I/O starts sending data one transfer clock cycle after the transmission enable condition is met. Transfer clock ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SP TxDi Transmission enable condition is met If SSS bit = 1, the serial I/O starts sending data at the rising edge (Note 1) of RxDi CLKi ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SP TxDi RxDi (Note 2) Note 1: The falling edge of RxDi when IOPOL=0; the rising edge of RxDi when IOPOL =1. Note 2: The transmit condition must be met before the falling edge (Note 1) of RxD. This diagram applies to the case where IOPOL=1 (reversed). Figure 10.29 Bus Collision Detect Function-Related Bits Page 132 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.7 Special Mode 4 (SIM Mode) (UART2) Based on UART mode, this is an SIM interface compatible mode. Direct and inverse formats can be implemented, and this mode allows to output a low from the TxD2 pin when a parity error is detected. Tables 10.17 lists the specifications of SIM mode. Table 10.18 lists the registers used in the SIM mode and the register values set. Table 10.17 SIM Mode Specifications Specification * Direct format * Inverse format * U2MR register's CKDIR bit = "0" (internal clock) : fi/ 16(n+1) fi = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of U2BRG register 0016 to FF16 * CKDIR bit = "1" (external clock) : fEXT/16(n+1) fEXT: Input from CLK2 pin. n: Setting value of U2BRG register 0016 to FF16 * Before transmission can start, the following requirements must be met _ The TE bit of U2C1 register= 1 (transmission enabled) _ The TI bit of U2C1 register = 0 (data present in U2TB register) * Before reception can start, the following requirements must be met _ The RE bit of U2C1 register= 1 (reception enabled) _ Start bit detection * For transmission When the serial I/O finished sending data from the U2TB transfer register (U2IRS bit =1) * For reception When transferring data from the UART2 receive register to the U2RB register (at completion of reception) * Overrun error (Note 1) This error occurs if the serial I/O started receiving the next data before reading the U2RB register and received the bit one before the last stop bit of the next data * Framing error This error occurs when the number of stop bits set is not detected * Parity error During reception, if a parity error is detected, parity error signal is output from the TxD2 pin. During transmission, a parity error is detected by the level of input to the RXD2 pin when a transmission interrupt occurs * Error sum flag This flag is set (= 1) when any of the overrun, framing, and parity errors is encountered Item Transfer data format Transfer clock Transmission start condition Reception start condition Interrupt request generation timing (Note 2) Error detection Note 1: If an overrun error occurs, the value of U2RB register will be indeterminate. The IR bit of S2RIC register does not change. Note 2: A transmit interrupt request is generated by setting the U2C1 register U2IRS bit to "1" (transmission complete) and U2ERE bit to "1" (error signal output) after reset. Therefore, when using SIM mode, be sure to clear the IR bit to "0" (no interrupt request) after setting these bits. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 133 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 10.18 Registers to Be Used and Settings in SIM Mode Function Set transmission data Reception data can be read Error flag Set a transfer rate Set to `1012' Select the internal clock or external clock Set to "0" Set this bit to "1" for direct format or "0" for inverse format Set to "1" Set to "0" Select the count source for the U2BRG register Invalid because CRD=1 Transmit register empty flag Set to "1" Set to "0" Set to "0" Set this bit to "0" for direct format or "1" for inverse format Set this bit to "1" to enable transmission Transmit buffer empty flag Set this bit to "1" to enable reception Reception complete flag Set to "1" Set to "0" Set this bit to "0" for direct format or "1" for inverse format Set to "1" Set to "0" Set to "0" Set to "0" Set to "0" 10. SERIAL I/O Register Bit U2TB(Note) 0 to 7 U2RB(Note) 0 to 7 OER,FER,PER,SUM U2BRG 0 to 7 U2MR SMD2 to SMD0 CKDIR STPS PRY PRYE IOPOL U2C0 CLK1, CLK0 CRS TXEPT CRD NCH CKPOL UFORM U2C1 TE TI RE RI U2IRS U2RRM U2LCH U2ERE U2SMR(Note) 0 to 3 U2SMR2 U2SMR3 U2SMR4 0 to 7 0 to 7 0 to 7 Note: Not all register bits are described above. Set those bits to "0" when writing to the registers in SIM mode. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 134 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O (1) Transmission Tc Transfer clock U2C1 register "1" TE bit "0" U2C1 register "1" TI bit "0" Write data to U2TB register Transferred from U2TB register to UART2 transmit register Start bit Parity Stop bit bit P SP ST D0 D1 D2 D3 D4 D5 D6 D7 P SP TxD2 Parity error signal sent back from receiver RxD2 pin level (Note) U2C0 register "1" TXEPT bit "0" S2TIC register "1" IR bit ST D0 D1 D2 D3 D4 D5 D6 D7 An "L" level returns due to the occurrence of a parity error. ST D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 D2 D3 D4 D5 D6 D7 P SP The level is detected by the interrupt routine. The level is detected by the interrupt routine. The IR bit is set to "1" at the falling edge of transfer clock "0" Cleared to "0" when interrupt request is accepted, or cleared to "0" in a program The above timing diagram applies to the case where data is transferred in the direct format. * U2MR register STPS bit = 0 (1 stop bit) * U2MR register PRY bit = 1 (even) * U2C0 register UFORM bit = 0 (LSB first) * U2C1 register U2LCH bit = 0 (no reverse) * U2C1 register U2IRSCH bit = 1 (transmit is completed) Tc = 16 (n + 1) / fi or 16 (n + 1) / fEXT fi : frequency of U2BRG count source (f1SIO, f2SIO, f8SIO, f32SIO) fEXT : frequency of U2BRG count source (external clock) n : value set to U2BRG Note : Because TxD2 and RxD2 are connected, this is composite waveform consisting of the TxD2 output and the parity error signal sent back from receiver. (1) Reception Tc Transfer clock U2C1 register "1" RE bit "0" Transmitter's transmit waveform Start bit ParityStop bit bit P SP ST D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 D2 D3 D4 D5 D6 D7 TxD2 RxD2 pin level (Note) An "L" level is output from TxD2 due to the occurrence of a parity error ST D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 D2 D3 D4 D5 D6 D7 P SP U2C0 register "1" RI bit "0" Read the U2RB register Read the U2RB register S2RIC register "1" IR bit "0" Cleared to "0" when interrupt request is accepted, or cleared to "0" in a program The above timing diagram applies to the case where data is received in direct format. * U2MR register STPS bit = 0 (1 stop bit) * U2MR register PRY bit = 1 (even) * U2C0 register UFORM bit = 0 (LSB first) * U2C1 register U2LCH bit = 0 (no reverse) * U2C1 register U2IRSCH bit = 1 (transmit is completed) Tc = 16 (n + 1) / fi or 16 (n + 1) / fEXT fi : frequency of U2BRG count source (f1SIO, f2SIO, f8SIO, f32SIO) fEXT : frequency of U2BRG count source (external clock) n : value set to U2BRG Note : Because TxD2 and RxD2 are connected, this is composite waveform consisting of the transmitter's transmit waveform and the parity error signal received. Figure 10.30 Transmit and Receive Timing in SIM Mode Page 135 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O Figure 10.31 shows the example of connecting the SIM interface. Connect TXD2 and RXD2 and apply pull-up. Microcomputer SIM card TxD2 RxD2 Figure 10.31 SIM Interface Connection 10.7.1 Parity Error Signal Output The parity error signal is enabled by setting the U2C1 register's U2ERE bit to "1". * When receiving The parity error signal is output when a parity error is detected while receiving data. This is achieved by pulling the TxD2 output low with the timing shown in Figure 10.32. If the U2RB register is read while outputting a parity error signal, the PER bit is cleared to "0" and at the same time the TxD2 output is returned high. * When transmitting A transmission-finished interrupt request is generated at the falling edge of the transfer clock pulse that immediately follows the stop bit. Therefore, whether a parity signal has been returned can be determined by reading the port that shares the RxD2 pin in a transmission-finished interrupt service routine. Transfer clock RxD2 TxD2 "H" "L" "H" "L" "H" "L" ST D0 D1 D2 D3 D4 D5 D6 D7 P SP (Note) U2C1 register "1" RI bit "0" This timing diagram applies to the case where the direct format is implemented. Note: The output of microcomputer is in the high-impedance state (pulled up externally). ST : Start bit P : Even Parity SP : Stop bit Figure 10.32 Parity Error Signal Output Timing Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 136 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.7.2 Format * Direct Format Set the U2MR register's PRY bit to "1", U2C0 register's UFORM bit to "0" and U2C1 register's U2LCH bit to "0". * Inverse Format Set the PRY bit to "0", UFORM bit to "1" and U2LCH bit to "1". Figure 10.33 shows the SIM interface format. (1) Direct format Transfer clock TxD2 "H" "L" "H" "L" D0 D1 D2 D3 D4 D5 D6 D7 P P : Even parity (2) Inverse format Transfer clock TxD2 "H" "L" "H" "L" D7 D6 D5 D4 D3 D2 D1 D0 P P : Odd parity Figure 10.33 SIM Interface Format Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 137 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.8 SI/O3 and SI/O4 SI/O3 and SI/O4 are exclusive clock-synchronous serial I/Os. Figure 10.34 shows the block diagram of SI/O3 and SI/O4, and Figure 10.35 shows the SI/O3 and SI/O4- related registers. Table 10.19 shows the specifications of SI/O3 and SI/O4. 1/2 Main clock f1SIO f2SIO PCLK1=0 Clock source select SMi1 to SMi0 002 f8SIO f32SIO 012 102 Synchronous circuit Data bus 1/8 PCLK1=1 1/4 1/2 1/(n+1) SiBRG register SMi4 CLKi CLK polarity reversing circuit SMi3 SMi6 SMi6 SI/O counter i SI/Oi interrupt request SMi2 SMi3 SOUTi SINi SMi5 LSB MSB SiTRR register 8 Note: i = 3, 4. n = A value set in the SiBRG register. Figure 10.34 SI/O3 and SI/O4 Block Diagram Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 138 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O S I/Oi control register (i = 3, 4) (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol S3C S4C Bit symbol SMi0 SMi1 SMi2 SMi3 SMi4 Address 036216 036616 Bit name After reset 010000016 010000016 Description b1 b0 RW RW RW RW RW Internal synchronous clock select bit 0 0 : Selecting f1SIO or f2SIO 0 1 : Selecting f8SIO 1 0 : Selecting f32SIO 1 1 : Must not be set. 0 : SOUTi output 1 : SOUTi output disable(high impedance) SOUTi output disable bit (Note 4) S I/Oi port select bit CLK polarity select bit 0 : Input/output port 1 : SOUTi output, CLKi function 0 : Transmit data is output at falling edge of transfer clock and receive data is input at rising edge 1 : Transmit data is output at rising edge of transfer clock and receive data is input at falling edge RW SMi5 SMi6 SMi7 Transfer direction select bit Synchronous clock select bit SOUTi initial value set bit 0 : LSB first 1 : MSB first 0 : External clock (Note 2) 1 : Internal clock (Note 3) Effective when SMi3 = 0 0 : "L" output 1 : "H" output RW RW RW Note 1: Make sure this register is written to by the next instruction after setting the PRCR register's PRC2 bit to "1" (write enable). Note 2: Set the SMi3 bit to "1" and the corresponding port direction bit to "0" (input mode). Note 3: Set the SMi3 bit to "1" (SOUTi output, CLKi function). Note 4: When the SMi2 bit is set to "1", the target pin goes to a high-impedance state regardless of which function of the pin is being used. SI/Oi bit rate generator (i = 3, 4) (Notes 1, 2) b7 b0 Symbol S3BRG S4BRG Description Address 036316 036716 After reset Indeterminate Indeterminate Setting range 0016 to FF16 RW WO Assuming that set value = n, BRGi divides the count source by n + 1 Note 1: Write to this register while serial I/O is neither transmitting nor receiving. Note 2: Use MOV instruction to write to this register. SI/Oi transmit/receive register (i = 3, 4) (Note 1, 2) b7 b0 Symbol S3TRR S4TRR Address 036016 036416 Description After reset Indeterminate Indeterminate RW RW Transmission/reception starts by writing transmit data to this register. After transmission/reception finishes, reception data can be read by reading this register. Note 1: Write to this register while serial I/O is neither transmitting nor receiving. Note 2: To receive data, set the corresponding port direction bit for SINi to "0" (input mode). Figure 10.35 S3C and S4C Registers, S3BRG and S4BRG Registers, and S3TRR and S4TRR Registers Page 139 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 10.19 SI/O3 and SI/O4 Specifications Specification * Transfer data length: 8 bits 10. SERIAL I/O Item Transfer data format Transfer clock * SiC (i=3, 4) register's SMi6 bit = "1" (internal clock) : fj/ 2(n+1) 0016 to FF16. fj = f1SIO, f8SIO, f32SIO. n=Setting value of SiBRG register * SMi6 bit = "0" (external clock) : Input from CLKi pin (Note 1) * Before transmission/reception can start, the following requirements must be met Write transmit data to the SiTRR register (Notes 2, 3) * When SiC register's SMi4 bit = 0 The rising edge of the last transfer clock pulse (Note 4) * When SMi4 = 1 The falling edge of the last transfer clock pulse (Note 4) Transmission/reception start condition Interrupt request generation timing CLKi pin function SOUTi pin function SINi pin function Select function I/O port, transfer clock input, transfer clock output I/O port, transmit data output, high-impedance I/O port, receive data input * LSB first or MSB first selection Whether to start sending/receiving data beginning with bit 0 or beginning with bit 7 can be selected * Function for setting an SOUTi initial value set function When the SiC register's SMi6 bit = 0 (external clock), the SOUTi pin output level while not transmitting can be selected . * CLK polarity selection Whether transmit data is output/input timing at the rising edge or falling edge of transfer clock can be selected. Note 1: To set the SiC register's SMi6 bit to "0" (external clock), follow the procedure described below. * If the SiC register's SMi4 bit = 0, write transmit data to the SiTRR register while input on the CLKi pin is high. The same applies when rewriting the SiC register's SMi7 bit. * If the SMi4 bit = 1, write transmit data to the SiTRR register while input on the CLKi pin is low. The same applies when rewriting the SMi7 bit. * Because shift operation continues as long as the transfer clock is supplied to the SI/Oi circuit, stop the transfer clock after supplying eight pulses. If the SMi6 bit = 1 (internal clock), the transfer clock automatically stops. Note 2: Unlike UART0 to UART2, SI/Oi (i = 3 to 4) is not separated between the transfer register and buffer. Therefore, do not write the next transmit data to the SiTRR register during transmission. Note 3: When the SiC register's SMi6 bit = 1 (internal clock), SOUTi retains the last data for a 1/2 transfer clock period after completion of transfer and, thereafter, goes to a high-impedance state. However, if transmit data is written to the SiTRR register during this period, SOUTi immediately goes to a high-impedance state, with the data hold time thereby reduced. Note 4: When the SiC register's SMi6 bit = 1 (internal clock), the transfer clock stops in the high state if the SMi4 bit = 0, or stops in the low state if the SMi4 bit = 1. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 140 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.8.1 SI/Oi Operation Timing Figure 10.36 shows the SI/Oi operation timing 1.5 cycle (max) (Note 3) SI/Oi internal clock CLKi output Signal written to the SiTRR register SOUTi output SINi input "H" "L" "H" "L" "H" "L" (Note 2) "H" "L" "H" "L" D0 D1 D2 D3 D4 D5 D6 D7 SiIC register IR bit i= 3, 4 "1" "0" Note 1: This diagram applies to the case where the SiC register bits are set as follows: SMi2=0 (SOUTi output), SMi3=1 (SOUTi output, CLKi function), SMi4=0 (transmit data output at the falling edge and receive data input at the rising edge of the transfer clock), SMi5=0 (LSB first) and SMi6=1 (internal clock) Note 2: When the SMi6 bit = 1 (internal clock), the SOUTi pin is placed in the high-impedance state after the transfer finishes. Note 3: If the SMi6 bit=0 (internal clock), the serial I/O starts sending or receiving data a maximum of 1.5 transfer clock cycles after writing to the SiTRR register. Figure 10.36 SI/Oi Operation Timing 10.8.2 CLK Polarity Selection The SiC register's SMi4 bit allows selection of the polarity of the transfer clock. Figure 10.37 shows the polarity of the transfer clock. (1) When SiC register's SMi4 bit = "0" CLKi SINi SOUTi D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7 (Note 2) (2) When SiC register's SMi4 bit = "1" CLKi SINi SOUTi D0 D0 D1 D1 D2 D2 D3 D3 D4 D4 D5 D5 D6 D6 D7 D7 (Note 3) i=3 and 4 Note 1: This diagram applies to the case where the SiC register bits are set as follows: SMi5=0 (LSB first) and SMi6=1 (internal clock) Note 2: When the SMi6 bit=1 (internal clock), a high level is output from the CLKi pin if not transferring data. Note 3: When the SMi6 bit=1 (internal clock), a low level is output from the CLKi pin if not transferring data. Figure 10.37 Polarity of Transfer Clock Page 141 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. SERIAL I/O 10.8.3 Functions for Setting an SOUTi Initial Value If the SiC register's SMi6 bit = 0 (external clock), the SOUTi pin output can be fixed high or low when not transferring. Figure 10.38 shows the timing chart for setting an SOUTi initial value and how to set it. (Example) When "H" selected for SOUTi initial value (Note 1) Signal written to SiTRR register Setting of the initial value of SOUTi output and starting of transmission/ reception SMi7 bit Set the SMi3 bit to "0" (SOUTi pin functions as an I/O port) SMi3 bit Set the SMi7 bit to "1" (SOUTi initial value = "H") D0 SOUTi (internal) Set the SMi3 bit to "1" (SOUTi pin functions as SOUTi output) Port output D0 Initial value = "H" (Note 3) SOUTi pin output (i = 3, 4) Setting the SOUTi initial value to "H" (Note 2) Port selection switching (I/O port SOUTi) "H" level is output from the SOUTi pin Write to the SiTRR register Serial transmit/reception starts Note 1: This diagram applies to the case where the SiC register bits are set as follows: SMi2=0 (SOUTi output), SMi5=0 (LSB first) and SMi6=0 (external clock) Note 2: SOUTi can only be initialized when input on the CLKi pin is in the high state if the SiC register's SMi4 bit = 0 (transmit data output at the falling edge of the transfer clock) or in the low state if the SMi4 bit = 1 (transmit data output at the rising edge of the transfer clock). Note 3: If the SMi6 bit = 1 (internal clock) or if the SMi2 bit = 1 (SOUT output disabled), this output goes to the high-impedance state. Figure 10.38 SOUTi's Initial Value Setting Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 142 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE 11. Multi-master I2C-BUS Interface The multi-master I2C-BUS interface have each dedicated circuit and operate independently. The multi-master I2C-BUS interface is a serial communications circuit, conforming to the Philips I2C-BUS data transfer format. This interface i, offering both arbitration lost detection and a synchronous functions, is useful for the multi-master serial communications. Table 11.1 shows multi-master I2C-BUS interface functions. This multi-master I2C-BUS interface consists of I2C address register, I2C data shift register, I2C clock control register, I2C control register, I2C status register, I2C transmit buffer register and the other control circuits. Table 11.1 Format Clock Generation Circuit Specifications Item Function In conformity with Philips I2C-BUS standard: 10-bit addressing format 7-bit addressing format High-speed clock mode Standard clock mode In conformity with Philips I2C-BUS standard: Master transmission Master reception Slave transmission Slave reception 16.1 kHz to 400 kHz (BCLK = 16 MHz) (SCL3/SDA3) : VCC1 Communication mode SCL clock frequency Power supply voltage on bus line Note. Our company doesn't assume the responsibility of the patent of the third party who originates in the use of the function to control the connection of I 2 C-BUS interface and ports (SCL3, SDA3) and other infringements of right. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 143 of 326 Figure 11.1 b7 SAD6 SAD5 SAD4 SAD3 SAD2 SAD1SAD0 R BW M306H7MG-XXXFP/MC-XXXFP/FGFP Rev.2.10 Oct 25, 2006 REJ03B0152-0210 I2C address register (IICiS0D) b0 Interrupt generating circuit Interrupt request signal (IICiRQ) Address comparator SDA3 b7 I2C data shift register (IICS0) Noise elimination circuit b0 b7 MST TRX BB PIN Block Diagram of Multi-master I2C-BUS interface Data control circuit b0 AL AAS AD0 LRB Page 144 of 326 AL circuit Internal data bus Serial data (SDA) I2C statusregister (IICS1) BB circuit SCL3 b7 ACK I I2C clock control register (IICiS2) ACK FAST CCR4 CCR3 CCR2 CCR1 CCR0 BIT MODE Serial clock (SCL) Clock division Noise elimination circuit b0 b7 10BIT ALS SAD b0 ESO BC2 B C1 BC0 Clock control circuit I2C control register (IICS1D) BCLK 11. MULTI-MASTER I2C BUS INTERFACE Bit counter M306H7MG-XXXFP/MC-XXXFP/FGFP (1) Reserved register 11. MULTI-MASTER I2C BUS INTERFACE Reserved register b7 b6 b5 b4 b3 b2 b1 b0 Symbol RSVREG02E5 Address 02E516 When reset 00?000002 00000 00 Bit Symbol Reserved bits Multi-master I2C-BUS RSVREG02E52 interface enable bit Bit name Function Must always be set to "0" RW WO 0 = Non active 1 = Active RW Reserved bits Must always be set to "0" WO Figure 11.2 Reserved register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 145 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE (2) I2C data shift register, I2C transmit buffer register The I2C data shift register is an 8-bit shift register to store receive data and write transmit data. When transmit data is written into this register, it is transferred to the outside from bit 7 in synchronization with the SCL clock, and each time one-bit data is output, the data of this register are shifted one bit to the left. When data is received, it is input to this register from bit 0 in synchronization with the SCL clock, and each time one-bit data is input, the data of this register are shifted one bit to the left. The I2C data shift register is in a write enable status only when the ESO bit of the I2C control register is "1." The bit counter is reset by a write instruction to the I2C data shift register. When both the ESO bit and the MST bit of the I2C status register are "1," the SCL is output by a write instruction to the I2C data shift register. Reading data from the I2C data shift register is always enabled regardless of the ESO bit value. The I2C transmit buffer register is a register to store transmit data (slave address) to the I2C data shift register before RESTART condition generation. That is, in master, transmit data written to the I2C transmit buffer register is written to the I2C data shift register simultaneously. However, the SCL is not output. The I2C transmit buffer register can be written only when the ESO bit is "1," reading data from the I2C transmit buffer register is disabled regardless of the ESO bit value. Notes 1: To write data into the I2C data shift register or the I2C transmit buffer register after the MST bit value changes from "1" to "0" (slave mode), keep an interval of 20 BCLK or more. 2: To generate START/RESTART condition after the I2C data shift register or the I2C transmit buffer register is written, keep an interval of 4 BCLK or more. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 146 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE I2C data shift register b7 b6 b5 b4 b3 b2 b1 b0 Symbol IIC0S0 Address 02E016 When reset Indeterminate Bit Symbol D0 D1 D2 D3 D4 D5 D6 D7 Bit name Data shift register Function This is an 8-bit shift register to store receive data and write transmit data. RW RW Note: To write data into the I2C data shift register after setting the MST bit to "0" (slave mode), keep an interval of 8 machine cycles or more. Figure 11.3 I2C data shift register I2C transmit buffer register b7 b6 b5 b4 b3 b2 b1 b0 Symbol IIC0S0S Address 02E616 When reset Indeterminate Bit Symbol S0S0 S0S1 S0S2 S0S3 S0S4 S0S5 S0S6 S0S7 Bit name Transmit buffer register Function This is an 8-bit register to write transmit data to I2C data shift register. RW WO Figure 11.4 I2C transmit buffer register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 147 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE (3) I2C address register The I2C address register consists of a 7-bit slave address and a read/write bit. In the addressing mode, the slave address written in this register is compared with the address data to be received immediately after the START condition are detected. * Bit 0: read/write bit (RBW) Not used when comparing addresses, in the 7-bit addressing mode. In the 10-bit addressing mode, the first address data to be received is compared with the contents (SAD6 to SAD0 + RBW) of the I2C address register. The RBW bit is cleared to "0" automatically when the stop condition is detected. * Bits 1 to 7: slave address (SAD0 to SAD6) These bits store slave addresses. Regardless of the 7-bit addressing mode and the 10-bit addressing mode, the address data transmitted from the master is compared with the contents of these bits. I2C address register b7 b6 b5 b4 b3 b2 b1 b0 Symbol IIC0S0D Address 02E116 When reset 0016 Bit Symbol RBW Bit name Read/write bit Function RW RW SAD0 SAD1 SAD2 SAD3 SAD4 SAD5 SAD6 Slave address RW Figure 11.5 I2C address register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 148 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE (4) I2C clock control register The I2C clock control register is used to set ACK control, SCL mode and SCL frequency. * Bits 0 to 4: SCL frequency control bits (CCR0-CCR4) These bits control the SCL frequency. * Bit 5: SCL mode specification bit (FAST MODE) This bit specifies the SCL mode. When this bit is set to "0," the standard clock mode is set. When the bit is set to "1," the high-speed clock mode is set. * Bit 6: ACK bit (ACK BIT) This bit sets the SDA status when an ACK clock is generated. When this bit is set to "0," the ACK return mode is set and SDA goes to LOW at the occurrence of an ACK clock. When the bit is set to "1," the ACK non-return mode is set. The SDA is held in the HIGH status at the occurrence of an ACK clock. However, when the slave address matches the address data in the reception of address data at ACK BIT = "0," the SDA is automatically made LOW (ACK is returned). If there is a mismatch between the slave address and the address data, the SDA is automatically made HIGH (ACK is not returned). ACK clock: Clock for acknowledgement * Bit 7: ACK clock bit (ACK) This bit specifies a mode of acknowledgment which is an acknowledgment response of data transmission. When this bit is set to "0," the no ACK clock mode is set. In this case, no ACK clock occurs after data transmission. When the bit is set to "1," the ACK clock mode is set and the master generates an ACK clock upon completion of each 1-byte data transmission.The device for transmitting address data and control data releases the SDA at the occurrence of an ACK clock (make SDA HIGH) and receives the ACK bit generated by the data receiving device. Note: Do not write data into the I2C clock control register during transmission. If data is written during transmission, the I2C clock generator is reset, so that data cannot be transmitted normally. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 149 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE I2C clock control register b7 b6 b5 b4 b3 b2 b1 b0 Symbol IIC0S2 Address 02E416 When reset 0016 Bit Symbol CCR0 Bit name SCL frequency control bits Setup value of CCR4-CCR0 00 to 02 03 04 05 06 : 1D 1E 1F Function Standard clock mode Setup disabled Setup disabled 100 83.3 17.2 16.6 16.1 High speed clock mode 333 250 400 (See note) 166 34.5 33.3 32.3 RW RW CCR1 Setup disabled Setup disabled CCR2 CCR3 500/CCR value 1000/CCR value CCR4 (at BCLK = 10 MHz, unit : kHz) FAST MODE ACK BIT ACK SCL mode specification 0 : Standard clock mode bit 1 : High-speed clock mode ACK bit ACK clock bit 0 : ACK is returned. 1 : ACK is not returned. 0 : No ACK clock 1 : ACK clock RW RW RW Note: At 400 kHz in the high-speed clock mode, the duty is as below. "0" period : "1" period = 3 : 2 In the other cases, the duty is as below. "0" period : "1" period = 1 : 1 Figure 11.6 I2C clock control register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 150 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP (5) I2C control register The I2C control register controls the data communication format. 11. MULTI-MASTER I2C BUS INTERFACE * Bits 0 to 2: bit counter (BC0-BC2) These bits decide the number of bits for the next 1-byte data to be transmitted. An interrupt request signal occurs immediately after the number of bits specified with these bits are transmitted. When a START condition is received, these bits become "0002" and the address data is always transmitted and received in 8 bits. Note: When the bit counter value = "1112," a STOP condition and START condition cannot be waited. * Bit 3: I2C-BUS interface use enable bit (ESO) This bit enables usage of the multimaster I2C-BUS interface i. When this bit is set to "0," the use disable status is provided, so the SDA and the SCL become high-impedance. When the bit is set to "1," use of the interface is enabled. When ESO = "0," the following is performed. * PIN = "1," BB = "0" and AL = "0" are set (they are bits of the I2C status register). * Writing data to the I2C data shift register and the I2C transmit buffer register is disabled. * Bit 4: data format selection bit (ALS) This bit decides whether or not to recognize slave addresses. When this bit is set to "0," the addressing format is selected, so that address data is recognized. When a match is found between a slave address and address data as a result of comparison or when a general call (refer to "(6) I2C status register," bit 1) is received, transmission processing can be performed. When this bit is set to "1," the free data format is selected, so that slave addresses are not recognized. * Bit 5: addressing format selection bit (10BIT SAD) This bit selects a slave address specification format. When this bit is set to "0," the 7-bit addressing format is selected. In this case, only the high-order 7 bits (slave address) of the I2C address register are compared with address data. When this bit is set to "1," the 10-bit addressing format is selected, all the bits of the I2C address register are compared with address data. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 151 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE I2C control register b7 b6 b5 b4 b3 b2 b1 b0 Symbol IIC0S1D Address 02E316 When reset 0016 Bit Symbol BC0 Bit name Bit counter (Number of transmit/receive bits) b2 b1 b0 Function 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 :8 :7 :6 :5 :4 :3 :2 :1 RW RW BC1 BC2 ESO ALS 10BIT SAD I2C-BUS interface use enable bit Data format selection bit 0 : Disabled 1 : Enabled 0 : Addressing format 1 : Free data format RW RW RW Address format selection 0 : 7-bit addressing format bit 1 : 10-bit addressing format Nothing is assigned. In an attempt to write to these bits, write "0." The value, if read, turns out to be "0." Figure 11.7 I2C control register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 152 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE (6) I2C status register The I2C status register controls the I2C-BUS interface status. Bits 0 to 3, 5 are read-only bits and bits 4, 6, 7 can be read out and written to. * Bit 0: last receive bit (LRB) This bit stores the last bit value of received data and can also be used for ACK receive confirmation. If ACK is returned when an ACK clock occurs, the LRB bit is set to "0." If ACK is not returned, this bit is set to "1." Except in the ACK mode, the last bit value of received data is input. The state of this bit is changed from "1" to "0" by executing a write instruction to the I2C data shift register or the I2C transmit buffer register. * Bit 1: general call detecting flag (AD0) This bit is set to "1" when a general call whose address data is all "0" is received in the slave mode. By a general call of the master device, every slave device receives control data after the general call. The AD0 bit is set to i0i by detecting the STOP condition or START condition. General call: The master transmits the general call address "0016"to all slaves. * Bit 2: slave address comparison flag (AAS) This flag indicates a comparison result of address data. < Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 153 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE * Bit 4: I2C-BUS interface interrupt request bit (PIN) This bit generates an interrupt request signal. Each time 1-byte data is transmitted, the state of the PIN bit changes from "1" to "0." At the same time, an interrupt request signal is sent to the CPU. The PIN bit is set to "0" in synchronization with a falling edge of the last clock (including the ACK clock) of an internal clock and an interrupt request signal occurs in synchronization with a falling edge of the PIN bit. When detecting the STOP condition in slave, the multi-master I2C-BUS interface interrupt request bit (IR) is set to "1" (interrupt requested) regardless of falling of PIN bit. When the PIN bit is "0," the SCL is kept in the "0" state and clock generation is disabled. Figure 11.9 shows an interrupt request signal generating timing chart. The PIN bit is set to "1" in any one of the following conditions. * Writing "1" to the PIN bit * Executing a write instruction to the I2C data shift register or the I2C transmit buffer register (See note). * When the ESO bit is "0" * At reset Note: It takes 12 BCLK cycles or more until PIN bit becomes "1" after write instructions are executed to these registers. The conditions in which the PIN bit is set to "0" are shown below: * Immediately after completion of 1-byte data transmission (including when arbitration lost is detected) * Immediately after completion of 1-byte data reception * In the slave reception mode, with ALS = "0" and immediately after completion of slave address or general call address reception * In the slave reception mode, with ALS = "1" and immediately after completion of address data reception * Bit 5: bus busy flag (BB) This bit indicates the status of use of the bus system. When this bit is set to "0," this bus system is not busy and a START condition can be generated. When this bit is set to "1," this bus system is busy and the occurrence of a START condition is disabled by the START condition duplication prevention function (See note). This flag cannot be written with software. In the other modes, this bit is set to "1" by detecting a START condition and set to "0" by detecting a STOP condition. When the ESO bit of the I2C control register is "0" and at reset, the BB flag is kept in the "0" state. * Bit 6: communication mode specification bit (transfer direction specification bit: TRX) This bit decides the direction of transfer for data communication. When this bit is "0," the reception mode is selected and the data of a transmitting device is received. When the bit is "1," the transmission mode is selected and address data and control data are output into the SDA in synchronization with the clock generated on the SCL. When the ALS bit of the I2C control register is "0" in the slave reception mode is selected, the TRX bit is set to "1" (transmit) if the least significant bit (R/W bit) of the address data transmitted by the master is "1." When the ALS bit is "0" and the R/W bit is "0," the TRX bit is cleared to "0" (receive). The TRX bit is cleared to "0" in one of the following conditions. * When arbitration lost is detected. * When a STOP condition is detected. * When occurrence of a START condition is disabled by the START condition duplication prevention function (Note). * With MST = "0" and when a START condition is detected. * With MST = "0" and when ACK non-return is detected. * At reset Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 154 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE * Bit 7: Communication mode specification bit (master/slave specification bit: MST) This bit is used for master/slave specification for data communication. When this bit is "0," the slave is specified, so that a START condition and a STOP condition generated by the master are received, and data communication is performed in synchronization with the clock generated by the master. When this bit is "1," the master is specified and a START condition and a STOP condition are generated, and also the clocks required for data communication are generated on the SCL. The MST bit is cleared to "0" in one of the following conditions. * Immediately after completion of 1-byte data transmission when arbitration lost is detected * When a STOP condition is detected. * When occurence of a START condition is disabled by the START condition duplication preventing function (See note). * At reset Note: The START condition duplication prevention function disables the following: the START condition generation; bit counter reset, and SCL output with the generation. This bit is valid from setting of BB flag to the completion of 1-byte transmission/reception (occurrence of transmission/ reception interrupt request) I2C status register b7 b6 b5 b4 b3 b2 b1 b0 Symbol IIC0S1 Address 02E216 When reset 0001000?2 Bit Symbol LRB AD0 AAS AL PIN BB TRX MST Bit name Last receive bit General call detecting flag 0 : Last bit = "0" 1 : Last bit = "1" Function (See note 1) RW RO RO RO (See note 1) RO (See note 1) 0 : No general call detected 1 : General call detected (See note 1) Slave address comparison 0 : Address mismatch flag 1 : Address match Arbitration lost detecting 0 : Not detected flag 1 : Detected I2C-BUS interface interrupt request bit Bus busy flag Communication mode specification bits 0 : Interrupt request issued RW 1 : No interrupt request issued (See note 2) 0 : Bus free 1 : Bus busy b7b6 (See note 1) RO RW 0 0 1 1 0 : Slave receive mode 1 : Slave transmit mode 0 : Master receive mode 1 : Master transmit mode Notes 1: These bits and flags can be read out, but cannot be written. 2: This bit can be written only "1." Figure 11.8 I2C status register SCL PIN IICIRQ Figure 11.9 Interrupt request signal generation timing Page 155 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE (7) START condition generation method When the ESO bit of the I2C control register is "1," execute a write instruction to the I2C status register to set the MST, TRX and BB bits to "1." A START condition will then be generated. After that, the bit counter becomes "0002" and an SCL for 1 byte is output. The START condition generation timing and BB bit set timing are different in the standard clock mode and the high-speed clock mode. Refer to Figure 11.10 for the START condition generation timing diagram, and Table 11.2 for the START condition/STOP condition generation timing table. I2Ci status register write signal SCL SDA BB flag Set time for BB flag Setup time Hold time Figure 11.10 START condition generation timing diagram (8) STOP condition generation method When the ESO bit of the I2C control register is "1," execute a write instruction to the I2C status register for setting the MST bit and the TRX bit to "1" and the BB bit to "0". A STOP condition will then be generated. The STOP condition generation timing and the BB flag reset timing are different in the standard clock mode and the highspeed clock mode. Refer to Figure 11.11 for the STOP condition generation timing diagram, and Table 11.2 for the START condition/STOP condition generation timing table. I2Ci status register write signal SCL SDA BB flag Setup time Hold time Reset time for BB flag Figure 11.11 STOP condition generation timing diagram Table 11.2 START condition/STOP condition generation timing table Item Standard Clock Mode 5.6 s 4.8 s 3.5 s High-speed Clock Mode 2.1 s 2.3 s 0.75 s Setup time (Min.) Hold time (Min.) Set/reset time for BB flag Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 156 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE (9) START/STOP condition detect conditions The START/STOP condition detect conditions are shown in Figure 11.12 and Table 11.3. Only when the 3 conditions of Table 11.3 are satisfied, a START/STOP condition can be detected. Note: When a STOP condition is detected in the slave mode (MST = 0), an interrupt request signal SCL release time SCL SDA (START condition) Setup time Setup time Hold time Hold time SDA (STOP condition) Figure 11.12 START condition/STOP condition detect timing diagram Table 11.3 START condition/STOP condition detect conditions Standard Clock Mode High-speed Clock Mode 1.0 s < SCL release time 0.5 s < Setup time 0.5 s < Hold time 6.5 s < SCL release time 3.25 s < Setup time 3.25 s < Hold time Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 157 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE (10) Address data communication There are two address data communication formats, namely, 7-bit addressing format and 10-bit addressing format. The respective address communication formats is described below. * 7-bit addressing format To meet the 7-bit addressing format, set the 10BIT SAD bit of the I2C control register to "0." The first 7-bit address data transmitted from the master is compared with the high-order 7-bit slave address stored in the I2C address register. At the time of this comparison, address comparison of the RBW bit of the I2C address register is not made. For the data transmission format when the 7-bit addressing format is selected, refer to Figure 11.13 (1) and (2). * 10-bit addressing format To meet the 10-bit addressing format, set the 10BIT SAD bit of the I2C control register to "1." An address comparison is made between the first-byte address data transmitted from the master and the 7-bit slave address stored in the I2C address register. At the time of this comparison, an address comparison between the RBW bit of the I2C address register and the R/W bit which is the last bit of the address data transmitted from the master is made. In the 10-bit addressing mode, the R/W bit which is the last bit of the address data not only specifies the direction of communication for control data but also is processed as an address data bit. When the first-byte address data matches the slave address, the AAS bit of the I2C status register is set to "1." After the second-byte address data is stored into the I2C data shift register, make an address comparison between the second-byte data and the slave address by software. When the address data of the 2nd bytes matches the slave address, set the RBW bit of the I2C address register to "1" by software. This processing can match the 7-bit slave address and R/W data, which are received after a RESTART condition is detected, with the value of the I2C address register. For the data transmission format when the 10-bit addressing format is selected, refer to Figure 11.13, (3) and (4). Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 158 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE (11) Example of Master Transmission An example of master transmission in the standard clock mode, at the SCL frequency of 100 kHz and in the ACK return mode is shown below. (1) Set a slave address in the high-order 7 bits of the I2C address register and "0" in the RBW bit. (2) Set the ACK return mode and SCL = 100 kHz by setting "8516" in the I2C clock control register. (3) Set "1016" in the I2C status register and hold the SCL at the HIGH. (4) Set a communication enable status by setting "0816" in the I2C control register. (5) Set the address data of the destination of transmission in the high-order 7 bits of the I2C data shift register and set "0" in the least significant bit. (6) Set "F016" in the I2C status register to generate a START condition. At this time, an SCL for 1 byte and an ACK clock automatically occurs. (7) Set transmit data in the I2C data shift register. At this time, an SCL and an ACK clock automatically occurs. (8) When transmitting control data of more than 1 byte, repeat step (7). (9) Set "D016" in the I2C status register. After this, if ACK is not returned or transmission ends, a STOP condition will be generated. (12) Example of Slave Reception An example of slave reception in the high-speed clock mode, at the SCL frequency of 400 kHz, in the ACK nonreturn mode, using the addressing format, is shown below. (1) Set a slave address in the high-order 7 bits of the I2C address register and "0" in the RBW bit. (2) Set the no ACK clock mode and SCL = 400 kHz by setting "2516" in the I2C clock control register. (3) Set "1016" in the I2C status register and hold the SCL at the HIGH. (4) Set a communication enable status by setting "0816" in the I2C control register. (5) When a START condition is received, an address comparison is made. (6) *When all transmitted address are"0" (general call): AD0 of the I2C status register is set to "1"and an interrupt request signal occurs. *When the transmitted addresses match the address set in (1): ASS of the I2C status register is set to "1" and an interrupt request signal occurs. *In the cases other than the above: AD0 and AAS of the I2C status register are set to "0" and no interrupt request signal occurs. (7) Set dummy data in the I2C data shift register. (8) When receiving control data of more than 1 byte, repeat step (7). (9) When a STOP condition is detected, the communication ends. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 159 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE S Slave address 7 bits R/W "0" A Data 1 to 8 bits A Data 1 to 8 bits A/A P (1) A master-transmitter transmits data to a slave-receiver S Slave address 7 bits R/W "1" A Data 1 to 8 bits A Data 1 to 8 bits A P (2) A master-receiver receives data from a slave-transmitter S Slave address 1st 7 bits 7 bits R/W "0" A Slave address 2nd byte 8 bits A Data 1 to 8 bits A Data 1 to 8 bits A/A P (3) A master-transmitter transmits data to a slave-receiver with a 10-bit address Slave address 1st 7 bits 7 bits S Slave address 1st 7 bits 7 bits R/W "0" A Slave address 2nd byte 8 bits A Sr R/W "1" A Data 1 to 8 bits A Data 1 to 8 bits A P (4) A master-receiver receives data from a slave-transmitter with a 10-bit address S : START condition A : ACK bit Sr : Restart condition P : STOP condition R/W :Read/Write bit From master to slave From slave to master Figure 11.13 Address data communication format (13) Precautions when using multi-master I2C-BUS interface * BCLK operation mode Select the no-division mode. * Used instructions Specify byte (.B) as data size to access multi-master I2C-BUS interface i-related registers. * Read-modify-write instruction The precautions when the read-modify-write instruction such as BSET, BCLR etc. is executed for each register of the multi-master I2C-BUS interface are described below. * I2C data shift register (IICS0) When executing the read-modify-write instruction for this register during transfer, data may become a value not intended. * I2C address register (IICS0D) When the read-modify-write instruction is executed for this register at detecting the STOP condition, data may become a value not intended. It is because hardware changes the read/write bit (RBW) at the above timing. * I2C status register (IICS1) Do not execute the read-modify-write instruction for this register because all bits of this register are changed by hardware. * I2C control register (IICS1D) When the read-modify-write instruction is executed for this register at detecting the START condition or at completing the byte transfer, data may become a value not intended. Because hardware changes the bit counter (BC0-BC2) at the above timing. * I2C clock control register (IICS2) The read-modify-write instruction can be executed for this register. * I2C port selection register (IICS2D) Since the read value of high-order 4 bits is indeterminate, the read-modify-write instruction cannot be used. * I2C transmit buffer register (IICS0S) Since the value of all bits is indeterminate, the read-modify-write instruction cannot be used. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 160 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP * START condition generating procedure using multi-master 11. MULTI-MASTER I2C BUS INTERFACE FCLR BTST JC BUSFREE: MOV.B NOP NOP NOP NOP MOV.B FSET BUSBUSY: FSET : I 5, IICS1 BUSBUSY SA, IICS0 (Interrupt disabled) (BB flag confirming and branch process) (Writing of slave address value #F0H, IICS1 I : I : (Trigger of START condition generating) (Interrupt enabled) (Interrupt enabled) (1) Be sure to add NOP instruction x 4 between writing the slave address value and setting trigger of START condition generating shown the above procedure example. (2) When using multi-master system, disable interrupts during the following three process steps: * BB flag confirming * Writing of slave address value * Trigger of START condition generating When the condition of the BB flag is bus busy, enable interrupts immediately. When using single-master system, it is not necessary to disable interrupts above. * RESTART condition generating procedure MOV.B NOP NOP MOV.B : SA, IICS0S (Writing of slave address value (1) #F0H, IICS1 : (Trigger of RESTART condition generating) (1) Use the I2C transmit buffer register to write the slave address value to the I2C data shift register. And also, be sure to add NOP instruction x 4. * Writing to I2C status register Do not execute an instruction to set the PIN bit to "1" from "0" and an instruction to set the MST and TRX bits to "0" from "1" simultaneously. It is because it may enter the state that the SCL pin is released and the SDA pin is released after about one machine cycle. Do not execute an instruction to set the MST and TRX bits to "0" from "1" simultaneously when the PIN bit is "1." It is because it may become the same as above. * Process of after STOP condition generating Do not write data in the I2C data shift register (IICS0) and the I2C status register (IICS1) until the bus busy flag BB becomes "0" after generating the STOP condition in the master mode. It is because the STOP condition waveform might not be normally generated. Reading to the above registers do not have the problem. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 161 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. MULTI-MASTER I2C BUS INTERFACE I2C0 Interrupt Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 00 Symbol EXTIICINT Address 02D616 At reset 0016 Bit symbol Reserved bits EXTIICINT0 EXTIICINT1 EXTIICINT2 EXTIICINT3 Bit name Must set to "0." ACK interrupt control bit (Note 1) Function RW 0000: Interrupt prohibition (Note 2) 0101: Interrupt permission Other: Must not be set Please set TA4IC (Note 3) when you use it by "Interrupt permission". Notes 1: Timer A4 and multi master I2C (ACK) interrupt, the vector and the interrupt control register are shared. Please make it to (b7, b6, b5, b4) = (0, 1, 0, 1) when you use multi-master I2C (ACK) interrupt. Notes 2: Please set 00002 when you use the interrupt of timer A4. Notes 3: Please refer to "Figure 6.3 interrupt control register" of "6.5 interrupt control". Notes 4: Please change in the part where multi-master I2C (ACK) and timer A4 interrupt request are not generated in the I2C0 interrupt control register. Notes 5: Please permit interrupt after making IR bit of timer A4 (TA4IC) "0" (the interrupt request none) after EXTIICINTi (i = 0 to 3) is changed. Reserved Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 00 0 0 Symbol RSVREG02D7 Address 02D716 At reset 0016 Bit symbol Reserved bit Reserved bit Reserved bit Reserved bit Reserved bits Bit name Must set to "0." Function RW When use multi-master I2C-BUS interface, set this bit to "1." Must set to "0." When use multi-master I2C-BUS interface, set this bit to "1." Must set to "0." Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 162 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER 12. A/D Converter The microcomputer contains one A/D converter circuit based on 8-bit successive approximation method configured with a capacitive-coupling amplifier. The analog inputs share the pins with P00 to P07, P95 and P96. Similarly, ADTRG input shares the pin with P97. Therefore, when using these inputs, make sure the corresponding port direction bits are set to "0" (= input mode). When not using the A/D converter, set the VCUT bit to "0" (= Vref unconnected), so that no current will flow from the VREF pin into the resistor ladder, helping to reduce the power consumption of the chip. The A/D conversion result is stored in the ADi register bits for ANi pins (i = 0 to 7). Table 12.1 shows the performance of the A/D converter. Figure 12.1 shows the block diagram of the A/D converter, and Figures 12.2 and 12.3 show the A/D converter-related registers. Table 12.1 Performance of A/D Converter Item Performance Method of A/D conversion Successive approximation (capacitive coupling amplifier) Analog input voltage (Note 1) 0V to AVCC (VCC) Operating clock AD (Note 2) f AD/divide-by-2 of fAD/divide-by-3 of f AD/divide-by-4 of f AD/divide-by-6 of f AD/divide-by-12 of f AD Resolution 8-bit Integral nonlinearity error When AVCC = VREF = 5V * With 8-bit resolution: 3LSB - ANEX0 and ANEX1 input (including mode in which external operation amp is connected) : 4LSB Operating modes One-shot mode, repeat mode, single sweep mode, repeat sweep mode 0, and repeat sweep mode 1 Analog input pins 8 pins (AN0 to AN7) + 2 pins (ANEX0 and ANEX1) A/D conversion start condition * Software trigger The ADCON0 register's ADST bit is set to "1" (A/D conversion starts) * External trigger (retriggerable) ___________ Input on the ADTRG pin changes state from high to low after the ADST bit is set to "1" (A/D conversion starts) Conversion speed per pin * Without sample and hold function 8-bit resolution: 49 AD cycles * With sample and hold function 8-bit resolution: 28 AD cycles Note 1: Does not depend on use of sample and hold function. Note 2: The AD frequency must be 10 MHz or less. Without sample-and-hold function, limit the AD frequency to 250kHZ or more. With the sample and hold function, limit the AD frequency to 1MHZ or more. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 163 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER A/D conversion rate selection CKS2=0 CKS1=1 CKS0=1 CKS0=0 AD CKS1=0 1/2 fAD 1/3 CKS2=1 TRG=0 Software trigger 1/2 ADTRG TRG=1 (VCC2) A/D trigger VREF VCUT=0 VCUT=1 Resistor ladder AVSS Successive conversion register ADCON1 register ADCON0 register AD register 0(8) AD register 1(8) AD register 2(8) AD register 3(8) AD register 4(8) AD register 5(8) AD register 6(8) AD register 7(8) Decoder for A/D register Data bus low-order ADCON2 register (address 03D416) Vref Decoder for channel selection VIN Port P0 group AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 CH2 to CH0 =0002 =0012 =0102 =0112 =1002 =1012 =1102 =111 2 Comparator OPA1 to OPA0=00 2 OPA1 to OPA0=11 2 ANEX0 ANEX1 OPA0=1 OPA1=1 OPA1 to OPA0 =012 OPA1=1 Figure 12.1 A/D Converter Block Diagram Page 164 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER A/D control register 0 (Note) b7 b6 b5 b4 b3 b2 b1 b0 Symbol ADCON0 Bit symbol CH0 Address 03D616 Bit name After reset 00000XXX2 Function Function varies with each operation mode RW RW Analog input pin select bit CH1 RW CH2 MD0 MD1 TRG ADST CKS0 Trigger select bit A/D conversion start flag A/D operation mode select bit 0 b4 b3 RW 0 0 : One-shot mode 0 1 : Repeat mode 1 0 : Single sweep mode 1 1 : Repeat sweep mode 0 or Repeat sweep mode 1 0 : Software trigger 1 : ADTRG trigger 0 : A/D conversion disabled 1 : A/D conversion started See Note 2 for the ADCON2 register RW RW RW RW RW Frequency select bit 0 Note: If the ADCON0 register is rewritten during A/D conversion, the conversion result will be indeterminate. A/D control register 1 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol ADCON1 Bit symbol SCAN0 Address 03D716 Bit name After reset 0016 Function Function varies with each operation mode RW RW A/D sweep pin select bit SCAN1 RW MD2 A/D operation mode select bit 1 Reserved bit Frequency select bit 1 Vref connect bit (Note 2) External op-amp connection mode bit 0 : Any mode other than repeat sweep mode 1 1 : Repeat sweep mode 1 Must always be set to "0" See Note 2 for the ADCON2 register 0 : Vref not connected 1 : Vref connected Function varies with each operation mode RW (b3) CKS1 VCUT OPA0 OPA1 RW RW RW RW RW Note 1: If the ADCON1 register is rewritten during A/D conversion, the conversion result will be indeterminate. Note 2: If the VCUT bit is reset from "0" (Vref unconnected) to "1" (Vref connected), wait for 1 s or more before starting A/D conversion. Figure 12.2 ADCON0 to ADCON1 Registers Page 165 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER A/D control register 2 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol ADCON2 Address 03D416 After reset 0016 01 0 Bit symbol SMP Bit name A/D conversion method select bit Reserved bit Reserved bit Reserved bit Frequency select bit 2 (Note 2) Function 0 : Without sample and hold 1 : With sample and hold Must always be set to "0" Must always be set to "1" Must always be set to "0" RW RW RW RW RW (b1) (b2) (b3) CKS2 0: Selects fAD, fAD divided by 2, or fAD divided by 4. RW 1: Selects fAD divided by 3, fAD divided by 6, or fAD divided by 12. (b7-b5) Nothing is assigned. In an attempt to write to these bits, write "0". The value, if read, turns out to be "0". Note 1: If the ADCON2 register is rewritten during A-D conversion, the conversion result will be indeterminate. Note 2: Adjust the frequency of AD to 10MHZ or less. AD can be selected by combining CKS0 bit of ADCON0 register, CKS1 bit of ADCON1 register and CKS2 bit of ADCON2 register. CKS2 0 0 0 0 1 1 1 1 CKS1 0 0 1 1 0 0 1 1 CKS0 0 1 0 1 0 1 0 1 AD Divide-by-4 of fAD Divide-by-2 of fAD fAD Ddivide-by-12 of fAD Divide-by-6 of fAD Divide-by-3 of fAD A/D register i (i=0 to 7) Symbol AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 Address 03C0 16 03C2 16 03C4 16 03C6 16 03C8 16 03CA 16 03CC 16 03CE 16 After reset Indeterminate Indeterminate Indeterminate Indeterminate Indeterminate Indeterminate Indeterminate Indeterminate b7 b0 Function A/D conversion result RW RO Figure 12.3 ADCON2 Register, and AD0 to AD7 Registers Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 166 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER 12.1 One-shot Mode In this mode, the input voltage on one selected pin is A/D converted once. Table 12.2 shows the specifications of one-shot mode. Figure 12.4 shows the ADCON0 to ADCON1 registers in one-shot mode. Table 12.2 One-shot Mode Specifications Item Function Specification The input voltage on one pin selected by the ADCON0 register's CH2 to CH0 bits and the ADCON1 register's OPA1 to OPA0 bits is A/D converted once. A/D conversion start condition * When the ADCON0 register's TRG bit is "0" (software trigger) The ADCON0 register's ADST bit is set to "1" (A/D conversion starts) ___________ * When the TRG bit is "1" (ADTRG trigger) ___________ Input on the ADTRG pin changes state from high to low after the ADST bit is set to "1" (A/D conversion starts) A/D conversion stop condition * Completion of A/D conversion (If a software trigger is selected, the ADST bit is cleared to "0" (A/D conversion halted).) * Set the ADST bit to "0" Interrupt request generation timing Completion of A/D conversion Analog input pin Select one pin from AN0 to AN7, ANEX0 to ANEX1 Reading of result of A/D converter Read one of the AD0 to AD7 registers that corresponds to the selected pin Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 167 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER A/D control register 0 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 00 Symbol ADCON0 Bit symbol CH0 Address 03D616 Bit name After reset 00000XXX2 Function b2 b1 b0 RW RW RW RW RW RW RW RW RW Analog input pin select bit CH1 CH2 MD0 MD1 TRG ADST CKS0 A/D operation mode select bit 0 Trigger select bit A/D conversion start flag Frequency select bit 0 0 0 0 : AN0 is selected 0 0 1 : AN1 is selected 0 1 0 : AN2 is selected 0 1 1 : AN3 is selected 1 0 0 : AN4 is selected 1 0 1 : AN5 is selected 1 1 0 : AN6 is selected 1 1 1 : AN7 is selected b4 b3 (Note 2) (Note 2) 0 0 : One-shot mode 0 : Software trigger 1 : ADTRG trigger 0 : A/D conversion disabled 1 : A/D conversion started See Note 2 for the ADCON2 register Note 1: If the ADCON0 register is rewritten during A/D conversion, the conversion result will be indeterminate. Note 2: After rewriting the MD1 to MD0 bits, set the CH2 to CH0 bits over again using another instruction. A/D control register 1 (Note) b7 b6 b5 b4 b3 b2 b1 b0 1 00 Symbol ADCON1 Bit symbol SCAN0 SCAN1 MD2 Address 03D716 Bit name After reset 0016 Function Invalid in one-shot mode RW RW RW A/D sweep pin select bit A/D operation mode select bit 1 Reserved bit Frequency select bit1 Set to "0" when one-shot mode is selected Must always be set to "0" See Note 2 for the ADCON2 register RW RW RW RW RW RW (b3) CKS1 VCUT OPA0 OPA1 Vref connect bit (Note 2) 1 : Vref connected External op-amp connection mode bit b7 b6 0 0 : ANEX0 and ANEX1 are not used 0 1 : ANEX0 input is A/D converted 1 0 : ANEX1 input is A/D converted 1 1 : External op-amp connection mode Note 1: If the ADCON1 register is rewritten during A/D conversion, the conversion result will be indeterminate. Note 2: If the VCUT bit is reset from "0" (Vref unconnected) to "1" (Vref connected), wait for 1 s or more before starting A/D conversion. Figure 12.4 ADCON0 Register and ADCON1 Register (One-shot Mode) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 168 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER 12.2 Repeat mode In this mode, the input voltage on one selected pin is A/D converted repeatedly. Table 12.3 shows the specifications of repeat mode. Figure 12.5 shows the ADCON0 to ADCON1 registers in repeat mode. Table 12.3 Repeat Mode Specifications Item Function Specification The input voltage on one pin selected by the ADCON0 register's CH2 to CH0 bits and the ADCON1 register's OPA1 to OPA0 bits is A/D converted repeatedly. A/D conversion start condition * When the ADCON0 register's TRG bit is "0" (software trigger) The ADCON0 register's ADST bit is set to "1" (A/D conversion starts) ___________ * When the TRG bit is "1" (ADTRG trigger) ___________ Input on the ADTRG pin changes state from high to low after the ADST bit is set to "1" (A/D conversion starts) A/D conversion stop condition Set the ADST bit to "0" (A/D conversion halted) Interrupt request generation timing None generated Analog input pin Select one pin from AN0 to AN7, ANEX0 to ANEX1 Reading of result of A/D converter Read one of the AD0 to AD7 registers that corresponds to the selected pin Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 169 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER A/D control register 0 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 01 Symbol ADCON0 Bit symbol CH0 CH1 Address 03D616 Bit name After reset 00000XXX2 Function b2 b1 b0 RW RW RW RW RW RW RW RW RW Analog input pin select bit CH2 MD0 MD1 TRG ADST CKS0 A/D operation mode select bit 0 Trigger select bit A/D conversion start flag Frequency select bit 0 0 0 0 : AN0 is selected 0 0 1 : AN1 is selected 0 1 0 : AN2 is selected 0 1 1 : AN3 is selected 1 0 0 : AN4 is selected 1 0 1 : AN5 is selected 1 1 0 : AN6 is selected 1 1 1 : AN7 is selected b4 b3 (Note 2) (Note 2) 0 1 : Repeat mode 0 : Software trigger 1 : ADTRG trigger 0 : A/D conversion disabled 1 : A/D conversion started See Note 2 for the ADCON2 register Note 1: If the ADCON0 register is rewritten during A/D conversion, the conversion result will be indeterminate. Note 2: After rewriting the MD1 to MD0 bits, set the CH2 to CH0 bits over again using another instruction. A/D control register 1 (Note) b7 b6 b5 b4 b3 b2 b1 b0 1 00 Symbol ADCON1 Bit symbol SCAN0 SCAN1 MD2 (b3) CKS1 VCUT OPA0 OPA1 Address 03D716 Bit name After reset 0016 Function Invalid in repeat mode RW RW RW A/D sweep pin select bit A/D operation mode select bit 1 Reserved bit Frequency select bit 1 Set to "0" when this mode is selected Must always be set to "0" See Note 2 for the ADCON2 register RW RW RW RW RW RW Vref connect bit (Note 2) 1 : Vref connected External op-amp connection mode bit b7 b6 0 0 : ANEX0 and ANEX1 are not used 0 1 : ANEX0 input is A/D converted 1 0 : ANEX1 input is A/D converted 1 1 : External op-amp connection mode Note 1: If the ADCON1 register is rewritten during A/D conversion, the conversion result will be indeterminate. Note 2: If the VCUT bit is reset from "0" (Vref unconnected) to "1" (Vref connected), wait for 1 s or more before starting A/D conversion. Figure 12.5 ADCON0 Register and ADCON1 Register (Repeat Mode) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 170 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER 12.3 Single Sweep Mode In this mode, the input voltages on selected pins are A/D converted, one pin at a time. Table 12.4 shows the specifications of single sweep mode. Figure 12.6 shows the ADCON0 to ADCON1 registers in single sweep mode. Table 12.4 Single Sweep Mode Specifications Item Function Specification The input voltages on pins selected by the ADCON1 register's SCAN1 to SCAN0 bits are A/D converted, one pin at a time. A/D conversion start condition * When the ADCON0 register's TRG bit is "0" (software trigger) The ADCON0 register's ADST bit is set to "1" (A/D conversion starts) ___________ * When the TRG bit is "1" (ADTRG trigger) ___________ Input on the ADTRG pin changes state from high to low after the ADST bit is A/D conversion stop condition set to "1" (A/D conversion starts) * Completion of A/D conversion (If a software trigger is selected, the ADST bit is cleared to "0" (A/D conversion halted).) * Set the ADST bit to "0" Interrupt request generation timing Completion of A/D conversion Analog input pin Select from AN0 to AN1 (2 pins), AN0 to AN3 (4 pins), AN0 to AN5 (6 pins), AN0 to AN7 (8 pins) Reading of result of A/D converter Read one of the AD0 to AD7 registers that corresponds to the selected pin Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 171 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER A/D control register 0 (Note) b7 b6 b5 b4 b3 b2 b1 b0 10 Symbol ADCON0 Bit symbol CH0 CH1 CH2 MD0 MD1 TRG ADST CKS0 Address 03D616 Bit name After reset 00000XXX2 Function Invalid in single sweep mode RW RW RW RW Analog input pin select bit A/D operation mode select bit 0 Trigger select bit A/D conversion start flag Frequency select bit 0 b4 b3 1 0 : Single sweep mode RW RW 0 : Software trigger 1 : ADTRG trigger 0 : A/D conversion disabled 1 : A/D conversion started See Note 2 for the ADCON2 register RW RW RW Note: If the ADCON0 register is rewritten during A/D conversion, the conversion result will be indeterminate. A/D control register 1 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 1 00 Symbol ADCON1 Bit symbol SCAN0 Address 03D716 Bit name After reset 0016 Function When single sweep mode is selected b1 b0 RW RW A/D sweep pin select bit SCAN1 A/D operation mode select bit 1 Reserved bit Frequency select bit 1 Vref connect bit (Note 2) External op-amp connection mode bit 0 0 : AN0 to AN1 (2 pins) 0 1 : AN0 to AN3 (4 pins) 1 0 : AN0 to AN5 (6 pins) 1 1 : AN0 to AN7 (8 pins) Set to "0" when single sweep mode is selected Must always be set to "0" See Note 2 for the ADCON2 register 1 : Vref connected b7 b6 RW RW RW RW RW RW RW MD2 (b3) CKS1 VCUT OPA0 OPA1 0 0 : ANEX0 and ANEX1 are not used 0 1 : Must not be set 1 0 : Must not be set 1 1 : External op-amp connection mode Note 1: If the ADCON1 register is rewritten during A/D conversion, the conversion result will be indeterminate. Note 2: If the VCUT bit is reset from "0" (Vref unconnected) to "1" (Vref connected), wait for 1 s or more before starting A/D conversion. Figure 12.6 ADCON0 Register and ADCON1 Register (Single Sweep Mode) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 172 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER 12.4 Repeat Sweep Mode 0 In this mode, the input voltages on selected pins are A/D converted repeatedly. Table 12.5 shows the specifications of repeat sweep mode 0. Figure 12.7 shows the ADCON0 to ADCON1 registers in repeat sweep mode 0. Table 12.5 Repeat Sweep Mode 0 Specifications Item Function Specification The input voltages on pins selected by the ADCON1 register's SCAN1 to SCAN0 bits are A/D converted repeatedly. A/D conversion start condition * When the ADCON0 register's TRG bit is "0" (software trigger) The ADCON0 register's ADST bit is set to "1" (A/D conversion starts) ___________ * When the TRG bit is "1" (ADTRG trigger) ___________ Input on the ADTRG pin changes state from high to low after the ADST bit is set to "1" (A/D conversion starts) A/D conversion stop condition Set the ADST bit to "0" (A/D conversion halted) Interrupt request generation timing None generated Analog input pin Select from AN0 to AN1 (2 pins), AN0 to AN3 (4 pins), AN0 to AN5 (6 pins), AN0 to AN7 (8 pins) Reading of result of A/D converter Read one of the AD0 to AD7 registers that corresponds to the selected pin Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 173 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER A/D control register 0 (Note) b7 b6 b5 b4 b3 b2 b1 b0 11 Symbol ADCON0 Bit symbol CH0 CH1 CH2 MD0 MD1 TRG ADST CKS0 Address 03D616 Bit name After reset 00000XXX2 Function Invalid in repeat sweep mode 0 RW RW RW RW Analog input pin select bit A/D operation mode select bit 0 Trigger select bit A/D conversion start flag Frequency select bit 0 b4 b3 1 1 : Repeat sweep mode 0 or Repeat sweep mode 1 0 : Software trigger 1 : ADTRG trigger 0 : A/D conversion disabled 1 : A/D conversion started See Note 2 for the ADCON2 register RW RW RW RW RW Note: If the ADCON0 register is rewritten during A/D conversion, the conversion result will be indeterminate. A/D control register 1 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 1 00 Symbol ADCON1 Bit symbol SCAN0 Address 03D716 Bit name After reset 0016 Function When repeat sweep mode 0 is selected b1 b0 RW RW RW RW RW RW RW RW RW A/D sweep pin select bit SCAN1 A/D operation mode select bit 1 Reserved bit Frequency select bit 1 Vref connect bit (Note 2) External op-amp connection mode bit 0 0 : AN0, AN1 (2 pins) 0 1 : AN0 to AN3 (4 pins) 1 0 : AN0 to AN5 (6 pins) 1 1 : AN0 to AN7 (8 pins) Set to "0" when repeat sweep mode 0 is selected Must always be set to "0" See Note 2 for the ADCON2 register 1 : Vref connected b7 b6 MD2 (b3) CKS1 VCUT OPA0 OPA1 0 0 : ANEX0 and ANEX1 are not used 0 1 : Must not be set 1 0 : Must not be set 1 1 : External op-amp connection mode Note 1: If the ADCON1 register is rewritten during A/D conversion, the conversion result will be indeterminate. Note 2: If the VCUT bit is reset from "0" (Vref unconnected) to "1" (Vref connected), wait for 1 s or more before starting A/D conversion. Figure 12.7 ADCON0 Register and ADCON1 Registers (Repeat Sweep Mode 0) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 174 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER 12.5 Repeat Sweep Mode 1 In this mode, the input voltages on all pins are A/D converted repeatedly, with priority given to the selected pins. Table 12.6 shows the specifications of repeat sweep mode 1. Figure 12.8 shows the ADCON0 to ADCON1 registers in repeat sweep mode 1. Table 12.6 Repeat Sweep Mode 1 Specifications Item Function Specification The input voltages on all selected pins are A/D converted repeatedly,with priority given to pins selected by the ADCON1 register's SCAN1 to SCAN0 bits. Example : If AN0 selected, input voltages are A/D converted in order of AN0 AN1 AN0 AN2 AN0 AN3, and so on. A/D conversion start condition * When the ADCON0 register's TRG bit is "0" (software trigger) The ADCON0 register's ADST bit is set to "1" (A/D conversion starts) ___________ * When the TRG bit is "1" (ADTRG trigger) ___________ Input on the ADTRG pin changes state from high to low after the ADST bit is set to "1" (A/D conversion starts) A/D conversion stop condition Set the ADST bit to "0" (A/D conversion halted) Interrupt request generation timing None generated Analog input pins to be given Select from AN0 (1 pins), AN0 to AN1 (2 pins), AN0 to AN2 (3 pins), AN0 to AN3 priority when A/D converted (4 pins) Reading of result of A/D converter Read one of the AD0 to AD7 registers that corresponds to the selected pin Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 175 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER A/D control register 0 (Note) b7 b6 b5 b4 b3 b2 b1 b0 11 Symbol ADCON0 Bit symbol CH0 CH1 CH2 MD0 MD1 TRG ADST CKS0 Address 03D616 Bit name After reset 00000XXX2 Function Invalid in repeat sweep mode 1 RW RW RW RW Analog input pin select bit A/D operation mode select bit 0 Trigger select bit A/D conversion start flag Frequency select bit 0 b4 b3 1 1 : Repeat sweep mode 0 or Repeat sweep mode 1 0 : Software trigger 1 : ADTRG trigger 0 : A/D conversion disabled 1 : A/D conversion started See Note 2 for the ADCON2 register RW RW RW RW RW Note: If the ADCON0 register is rewritten during A/D conversion, the conversion result will be indeterminate. A/D control register 1 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 1 01 Symbol ADCON1 Bit symbol SCAN0 Address 03D716 Bit name After reset 0016 Function When repeat sweep mode 1 is selected b1 b0 RW RW RW RW RW RW RW RW RW A/D sweep pin select bit SCAN1 A/D operation mode select bit 1 Reserved bit Frequency select bit 1 Vref connect bit (Note 2) External op-amp connection mode bit 0 0 : AN0 (1 pin) 0 1 : AN0, AN1 (2 pins) 1 0 : AN0 to AN2 (3 pins) 1 1 : AN0 to AN3 (4 pins) Set to "1" when repeat sweep mode 1 is selected Must always be set to "0" See Note 2 for the ADCON2 register 1 : Vref connected b7 b6 MD2 (b3) CKS1 VCUT OPA0 OPA1 0 0 : ANEX0 and ANEX1 are not used 0 1 : Must not be set 1 0 : Must not be set 1 1 : External op-amp connection mode Note 1: If the ADCON1 register is rewritten during A/D conversion, the conversion result will be indeterminate. Note 2: If the VCUT bit is reset from "0" (Vref unconnected) to "1" (Vref connected), wait for 1 s or more before starting A/D conversion. Figure 12.8 ADCON0 Register and ADCON1 Register (Repeat Sweep Mode 1) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 176 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER 12.6 Sample and Hold If the ADCON2 register's SMP bit is set to "1" (with sample-and-hold), the conversion speed per pin is increased to 28 AD cycles for 8-bit resolution. Sample-and-hold is effective in all operation modes. Select whether or not to use the sample-and-hold function before starting A/D conversion. 12.7 Extended Analog Input Pins In one-shot and repeat modes, the ANEX0 and ANEX1 pins can be used as analog input pins. Use the ADCON1 register's OPA1 to OPA0 bits to select whether or not use ANEX0 and ANEX1. The A/D conversion results of ANEX0 and ANEX1 inputs are stored in the AD0 and AD1 registers, respectively. 12.8 External Operation Amp Connection Mode Multiple analog inputs can be amplified using a single external op-amp via the ANXE0 and ANEX1 pins. Set the ADCON1 register's OPA1 OPA0 bits to `112' (external op-amp connection mode). The inputs from ANi (i = 0 to 7) are output from the ANEX0 pin. Amplify this output with an external op-amp before sending it back to the ANEX1 pin. The A/D conversion result is stored in the corresponding ADi register. The A/D conversion speed depends on the response characteristics of the external op-amp. Note that the ANXE0 and ANEX1 pins cannot be directly connected to each other. Figure 12.9 is an example of how to connect the pins in external operation amp. Microcomputer AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 Resistor ladder Successive conversion register ANEX0 ANEX1 Comparator External opamp Figure 12.9 External Op-amp Connection Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 177 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER 12.9 Current Consumption Reducing Function When not using the A/D converter, its resistor ladder and reference voltage input pin (VREF) can be separated using the ADCON1 register's VCUT bit. When separated, no current will flow from the VREF pin into the resistor ladder, helping to reduce the power consumption of the chip. To use the A/D converter, set the VCUT bit to "1" (VREF connected) and then set the ADCON0 register's ADST bit to "1" (A/D conversion start). The VCUT and ADST bits cannot be set to "1" at the same time. Nor can the VCUT bit be set to "0" (VREF unconnected) during A/D conversion. 12.10 Analog Input Pin and External Sensor Equivalent Circuit Example Figure 12.10 shows analog input pin and external sensor equivalent circuit example. Microcomputer Sensor equivalent circuit R0 VIN C VC R Sampling time Sample-and-hold function enabled: 3 fAD 2 Sample-and-hold function disabled: fAD Figure 12.10 Analog Input Pin and External Sensor Equivalent Circuit Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 178 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. A/D CONVERTER 12.11 Caution of Using A/D Converter (1) Make sure the port direction bits for those pins that are used as analog inputs are set to "0" (input mode). Also, if the ADCON0 register's TGR bit = 1 (external trigger), make sure the port direction bit for the ADTRG pin is set to "0" (input mode). (2) To prevent noise-induced device malfunction or latchup, as well as to reduce conversion errors, insert capacitors between the AVCC, VREF, and analog input pins (ANi (i=0 to 7)) each and the AVSS pin. Similarly, insert a capacitor between the VCC pin and the VSS pin. Figure 12.11 is an example connection of each pin. (3) If the CPU reads the ADi register (i = 0 to 7) at the same time the conversion result is stored in the ADi register after completion of A/D conversion, an incorrect value may be stored in the ADi register. This problem occurs when a divide-by-n clock derived from the main clock or a subclock is selected for CPU clock. *When operating in one-shot or single-sweep mode Check to see that A/D conversion is completed before reading the target ADi register. (Check the IR bit in the ADIC register to see if A/D conversion is completed.) *When operating in repeat mode or repeat sweep mode 0 or 1 Use the main clock for CPU clock directly without dividing it. (4) If A/D conversion is forcibly terminated while in progress by setting the ADCON0 register's ADST bit to "0" (A/D conversion halted), the conversion result of the A/D converter is indeterminate. The contents of ADi registers irrelevant to A/D conversion may also become indeterminate. If while A/D conversion is underway the ADST bit is cleared to "0" in a program, ignore the values of all ADi registers. Microcomputer VCC1 VCC1 (16 pin) AVCC C4 VSS C2 VCC2 VCC2 (62 pin) C5 VSS ANi AVSS C3 VCC2 ANi: ANi (i=0 to 7) Note 1: C10.47F, C2 0.47F, C3 100pF, C4 0.1F, C50.1F (reference) Note 2: Use thick and shortest possible wiring to connect capacitors. Figure 12.11 VCC, VSS, AVCC, AVSS, VREF and ANi Connection Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 179 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 13. CRC CALCULATION 13. CRC Calculation The Cyclic Redundancy Check (CRC) operation detects an error in data blocks. The microcomputer uses a generator polynomial of CRC_CCITT (X16 + X12 + X5 + 1) to generate CRC code. The CRC code consists of 16 bits which are generated for each data block in given length, separated in 8 bit units. After the initial value is set in the CRCD register, the CRC code is set in that register each time one byte of data is written to the CRCIN register. CRC code generation for one-byte data is finished in two cycles. Figure 13.1 shows the block diagram of the CRC circuit. Figure 13.2 shows the CRC-related registers. Figure 13.3 shows the calculation example using the CRC operation. Data bus high-order Data bus low-order Eight low-order bits CRCD register Eight high-order bits CRC code generating circuit x16 + x12 + x5 + 1 CRCIN register Figure 13.1 CRC Circuit Block Diagram CRC data register (b15) b7 (b8) b0 b7 b0 Symbol CRCD Address 03BD16 to 03BC16 After reset Indeterminate Function When data is written to the CRCIN register after setting the initial value in the CRCD register, the CRC code can be read out from the CRCD register. Setting range RW 000016 to FFFF16 RW CRC input register b7 b0 Symbol CRCIN Function Data input Address 03BE16 After reset Indeterminate Setting range 0016 to FF16 RW RW Figure 13.2 CRCD Register and CRCIN Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 180 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 13. CRC CALCULATION Setup procedure and CRC operation when generating CRC code "80C416" (a) CRC operation performed by the M16C CRC code: Remainder of a division in which the value written to the CRCIN register with its bit positions reversed is divided by the generator polynomial Generator polynomial: X16 + X12 + X5 + 1 (1 0001 0000 0010 00012) (b) Setting procedure (1) Reverse the bit positions of the value "80C416" bytewise in a program. "8016" "0116", "C416" "2316" b15 b0 (2) Write 000016 (initial value) CRCD register b7 b0 (3) Write 0116 CRCIN register Two cycles later, the CRC code for "8016," i.e., 918816, has its bit positions reversed to become "118916" which is stored in the CRCD register. b15 b0 118916 CRCD register b7 b0 (4) Write 2316 CRCIN register Two cycles later, the CRC code for "80C416," i.e., 825016, has its bit positions reversed to become "0A4116" which is stored in the CRCD register. b15 b0 0A4116 CRCD register (c) Details of CRC operation In the case of (3) above, the value written to the CRCIN register "0116 (000000012)" has its bit positions reversed to become "100000002." The value "1000 0000 0000 0000 0000 00002" derived from that by adding 16 digits and the CRCD register's initial value "000016" are added, the result of which is divided by the generator polynomial using modulo-2 arithmetic. Modulo-2 operation is operation that complies with the law given below. Data 0+0=0 0+1=1 1+0=1 1+1=0 -1 = 1 1000 1000 1 0001 0000 0010 0001 1000 0000 0000 0000 1000 1000 0001 0000 Generator polynomial 1000 0001 0000 1000 1000 0001 1001 0001 CRC code 0000 1 1000 0000 1000 0000 0 1 1000 The value "0001 0001 1000 10012 (118916)" derived from the remainder "1001 0001 1000 10002 (918816)" by reversing its bit positions may be read from the CRCD register. If operation (4) above is performed subsequently, the value written to the CRCIN register "2316 (001000112)" has its bit positions reversed to become "110001002. The value "1100 0100 0000 0000 0000 00002" derived from that by adding 16 digits and the remainder in (3) "1001 0001 1000 10002" which is left in the CRCD register are added, the result of which is divided by the generator polynomial using modulo-2 arithmetic. The value "0000 1010 0100 00012 (0A4116)" derived from the remainder by reversing its bit positions may be read from the CRCD register. Figure 13.3 CRC Calculation Page 181 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION 14. Expansion Function 14.1 Expansion function description Expansion function consists of CRC operation function, data slice function and humming decoder function. Each function is controlled by expansion memories. 1. CRC operation function It performs error detection of a code, and error correction. 2. Data slice function It performs data acquisition to get such format data as below. Hardware : TELETEXT, PDC, VPS, VBI and EPG-J Software : WSS, CC, CC2X and ID-1 3. Humming decoder function It performs 8/4 humming and 24/18 humming BCLK Clock generator Vertical Syncseparate circuit Clock generator Clock generator SYNCIN Syncseparate circuit Timing generator Port control circuit CVIN Data slicer circuit Serial/pararell conversion circuit CRC register Expansion register 24/18 humming 8/4 humming Slice RAM Arbitration circuit Data bus (16bit) CPU block Figure 14.1 Block diagram of expansion function Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 182 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION 14.2 Expansion memory Expansion function memory is divided by 3 patterns ; Slice RAM, CRC registers and expansion registers (Humming decoder operates by the register placed on SFR). Data writing and read out to the Slice RAM, CRC registers and the expansion registers are carried out per 16 bit unit by the data setting register (addresses 020E16, 021016, 021216, 021416, 021616 and 021816) placed on SFR. Contents of each memory and data setting register are shown in Table 14.1. Table 14.1 Expansion memory composition Contents This register holds acquired data. This register controls a set up generation polynomial and code data. This register performs data slicer control and VBI encoder control. Data setting register Slice RAM address control register (020E16) Slice RAM data control register (021016) CRC register address control register (021216) CRC register data control register (021416) Expansion register address control register (021616) Expansion register data control register (021816) Expansion memory Slice RAM CRC register Expansion register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 183 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION 14.3 Slice RAM Slice RAM stores 18-line slice data. There are several types of Slice data : PDC, VPS, VBI, XDS, WSS, etc. All data are stored to addresses which corresponds to slice line (ex. 22 line' data is stored to addresses 20016 to 21716 ). 24 addresses (SR00x to SR17x) are prepared for 1 line, slice data is stored in order from LSB side. Then, slice data type and field information are stored to the top address of each line. Slice RAM composition is shown in Table 14.2. Table 14.2 Slice RAM addresses (SA9 to SA0) Slice RAM composition SD15 SD14 SD13 SD12 SD11 SD10 SD9 SD8 SD7 SD6 SD5 SD4 SD3 SD2 SD1 SD0 Remarks (Note1) SR00F SR00E SR00D SR00C SR00B SR00A SR009 SR008 SR007 SR006 SR005 SR004 SR003 SR002 SR001 SR000 6th line or 318th line SR01F SR01E SR01D SR01C SR01B SR01A SR019 SR018 SR017 SR016 SR015 SR014 SR013 SR012 SR011 SR010 slice data 00016 00116 to 01616 01716 01816 to 01F16 02016 to 03716 04016 to 1F716 20016 to 21716 22016 to 23716 to to to to to to to to to to to to to to to to SR16F SR16E SR16D SR16C SR16B SR16A SR169 SR168 SR167 SR166 SR165 SR164 SR163 SR162 SR161 SR160 SR17F SR17E SR17D SR17C SR17B SR17A SR179 SR178 SR177 SR176 SR175 SR174 SR173 SR172 SR171 SR170 Unused area SR00F SR00E SR00D SR00C SR00B SR00A SR009 SR008 SR007 SR006 SR005 SR004 SR003 SR002 SR001 SR000 7th line or 319th line to to to to to to to to to to to to to to to to slice data SR17F SR17E SR17D SR17C SR17B SR17A SR179 SR178 SR177 SR176 SR175 SR174 SR173 SR172 SR171 SR170 8th line to 21th line or 320th line to 333 line slice data SR00F SR00E SR00D SR00C SR00B SR00A SR009 SR008 SR007 SR006 SR005 SR004 SR003 SR002 SR001 SR000 22th line or 334th line to to to to to to to to to to to to to to to to slice data SR17F SR17E SR17D SR17C SR17B SR17A SR179 SR178 SR177 SR176 SR175 SR174 SR173 SR172 SR171 SR170 SR00F SR00E SR00D SR00C SR00B SR00A SR009 SR008 SR007 SR006 SR005 SR004 SR003 SR002 SR001 SR000 23th line or 335th line to to to to to to to to to to to to to to to to slice data SR17F SR17E SR17D SR17C SR17B SR17A SR179 SR178 SR177 SR176 SR175 SR174 SR173 SR172 SR171 SR170 Note 1. This is the line to support when the PAL video signal is sliced and setting the expansion registers to VPS_VP8 to VPS_VP0 (bits 8 to 0 in address 2916) = "416". For accessing to Slice RAM data, set accessing address (SA9 to SA0) (shown in Table 14.2) to Slice RAM address control register (address 020E16 ). Then read out data from Slice RAM data control register (address 021016 ). When end the data reading, Slice RAM address control register increments address automatically. Then, next address data reading is possible. Do not access to unused area of each character codes. Must set address to each line because unused area has no address' automatically increment. Slice RAM bit composition is shown in Figure 14.2, Slice RAM access registers are shown in Figure14.3 and Slice RAM access block diagram is shown in Figure 14.4 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 184 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP . 14. EXPANSION FUNCTION Slice RAM bit composition The each head address of the address is corresponded to slice line following slice information. Line register 3 Line register 2 Line register 1 Other SR00F to SR004 0 0 0 0 SR003 field* field* field* field* SR002 0 0 0 0 SR001 1 1 0 0 SR000 1 0 1 0 * field * the first field : 1 the second field : 0 (1) PDC In case of the PDC data, 16 bits (2 data) are stored for the 1 address from the LSB side. Clock run-in + flaming code Data1 Data3 Data5 Data40 Data42 Data2 Data4 Data6 Data39 Data41 L S B ML SS BB M S B SR020 SR02F SR030 SR040 SR03F SR04F SR150 SR15F SR160 SR16F Note. The expansion register is the slice data storing pattern when setting the START (bit 1 in address 2816 bit) to "1". SR17x is the unused area. (2) VPS In case of the VPS data or the VBI data, 8 bits (a data) are stored for an address from the LSB side. Low-order 8 bits hold the slice data. And, high-order 8 bits hold warning bit, when the send data is not recognized as bi-phase type. The case of bi-phase data ="1,0" or "0,1" (the bi-phase type) becomes "0" for this warning bit, and it becomes "1" in bi-phase data="0,0" or "1,1" (it is not the bi-phase type). (For example, bi-phase data of SR011 is "0,0" or "1,1", "1" is set to SR019.) Clock run-in + flaming code Data1 L S B ML SS BB Data2 M S B Data3 Data4 Data11 Data12 Data13 SR020 SR027 SR030 SR040 SR037 SR047 SR050 SR057 SR0C0 SR0C7 SR0D0 SR0E0 SR0D7 SR0E7 Note. The expansion register is the slice data storing pattern when setting the START (bit 1 in address 2816 bit) to "1". From SR0Fx to SR17x are the unused area. (3) EPG-J Clock run-in + flaming code Data1 Data2 Data3 Data4 Data5 Data6 Data31 Data32 Data33 Data34 C S B ML SS BB M S B SR020 SR02F SR030 SR040 SR03F SR04F SR110 SR11F SR120 SR12F Note. The expansion register is the slice data storing pattern when setting the START (bit 1 in address 2816 bit) to "1". From SR13x to SR17x are the unused area. Figure 14.2 Slice RAM bit composition Page 185 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP . Slice RAM address control register b15 b9 b8 b7 b0 14. EXPANSION FUNCTION Symbol SA Address 020E16 When reset 000016 Function Specify accessing Slice RAM address Nothing is assigned. When write, set to "0." When read, its content is indeterminate. Setting possible value R W 00016 to 23716 Note 1 : When access to Slice RAM, Slice RAM address control register (020E16) should be set at first. Slice RAM address control register increments by accessing Slice RAM data control register. So, it is not neccesary to setting the next Slice RAM address. Note 2 : When read Slice RAM data by software during slicer operation, access to Slice RAM after 1 horizontal synchronous period from the completion of a SLICEON (refer to 14.6 Expansion Register Construction Composition for a SLICEON period). Slice RAM data control register b15 b9 b8 b7 b0 Symbol SD Address 021016 When reset 000016 Function Read out the data of Slice RAM. Read out data of Slice RAM which is specified by Slice RAM address control register (address 020E16) by reading this register. RW Note : Data access must be 16-bit unit. 8-bit unit access is disable. Figure 14.3 Slice RAM access registers. Data bus (16-bit) (address 020E16) Slice RAM address control register (10) (SA9 to SA0) Slice RAM data control register (16) (SD15 to SD0) (address 021016) Increment automatically after data access Slice RAM Figure 14.4 Slice RAM access block diagram Page 186 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION 14.4 CRC Operation Circuit (EPG-J) CRC operation circuit (EPG-J) is a circuit for performing error detection and error correction by the 272-190 shortening difference set cyclic code which is a coding system in a data multiplex broadcast. CRC register consists of registers shown in Figure 14.5. CRC register can perform error detection and error correction by majority logic by setting up a generator polynomial, code data, etc. CRC register composition is shown in Table 14.3. Table 14.3 CA3 to CA0 CRC register composition CD13 DAOUT13 _ CRC_68 CRC_52 CRC_36 CRC_20 CRC_04 _ REG_C79 _ _ _ _ _ CD12 DAOUT12 _ CRC_69 CRC_53 CRC_37 CRC_21 CRC_05 _ REG_C78 _ _ _ _ _ CD11 DAOUT11 _ CRC_70 CRC_54 CRC_38 CRC_22 CRC_06 _ REG_C77 _ _ _ _ _ CD0 CD1 CD2 CD3 CD4 CD5 CD6 CD7 CD8 CD9 CD10 DAOUT0 DAOUT1 DAOUT2 DAOUT3 DAOUT4 DAOUT5 DAOUT6 DAOUT7 DAOUT8 DAOUT9 DAOUT10 CRC_ERR10 CRC_ERR09 CRC_ERR08 CRC_ERR07 CRC_ERR06 CRC_ERR05 CRC_ERR04 CRC_ERR03 CRC_ERR02 CRC_ERR01 CRC_ERR00 CRC_71 CRC_72 CRC_73 CRC_76 CRC_77 CRC_78 CRC_79 CRC_80 CRC_81 CRC_75 CRC_74 CRC_55 CRC_56 CRC_57 CRC_60 CRC_61 CRC_62 CRC_63 CRC_64 CRC_65 CRC_59 CRC_58 CRC_49 CRC_48 CRC_47 CRC_46 CRC_45 CRC_44 CRC_43 CRC_42 CRC_41 CRC_40 CRC_39 CRC_33 CRC_32 CRC_31 CRC_30 CRC_29 CRC_28 CRC_27 CRC_26 CRC_25 CRC_24 CRC_23 CRC_07 CRC_17 CRC_16 CRC_15 CRC_14 CRC_13 CRC_12 CRC_11 CRC_10 CRC_09 CRC_08 CRC_01 CRC_00 _ _ _ _ _ _ _ _ _ REG_C76 _ _ _ _ _ REG_C75 _ _ _ _ _ REG_C74 _ _ _ _ _ REG_C73 _ _ _ _ _ REG_C72 _ _ _ _ _ REG_C71 _ _ _ _ _ REG_C70 _ _ _ _ CRC16SEL REG_C69 _ _ _ _ _ REG_C68 _ _ _ _ _ REG_C67 _ _ _ _ _ REG_C66 _ _ _ _ _ Remarks 0016 0116 0216 0316 0416 0516 0616 0716 0816 0916 0A16 0B16 0C16 0D16 CD15 DAOUT15 _ CRC_66 CRC_50 CRC_34 CRC_18 CRC_02 _ REG_C81 _ _ _ _ _ CD14 DAOUT14 _ CRC_67 CRC_51 CRC_35 CRC_19 CRC_03 _ REG_C80 _ _ _ _ _ CRC register address control register b15 b14 b13 b8 b7 b5 b4 b3 b0 Symbol CA Function Specify accessing CRC register address. CRC register address automatic increment. 0: enable / 1 : disable (Notes 2) address 021216 at Reset 000016 The value which R W can be set up 0016 to 0D16 - Nothing is assigned. When write, set to "0." When read, its content is determinate. CRCLOOP 0 to 5 The number of times of a CRC operation repetition. Error detection / error correction Selection setting 0:error detection mode / 1: Error correction mode -- 0016 to 3F16 - - CRCCHANGE CRCON CRC operation 0: Stop/1 : Operation (Note 3) Notes 1: When access to CRC register, must be set CRC register address at first, then use CRC register data control register (021416). Notes 2: When bit 4 = "0" setting, CRC register data control register increments by accessing CRC register data control register, so it is not necessary to setting the next CRC register address. When bit 4 = "1" setting, the address is fixed. Notes 3: When bit 15 = "0" setting, the value of a CRC data register (address (CA3 to CA0) =01 to 07) is cleared. CRC register data control register b15 b8b7 b0 Symbol CD address 021416 at Reset 000016 The value which can be set up Function Write and read out the data of CRC register which is specified by CRC register address control register (address 021216) RW 000016 to FFFF16 Note: Data access must be 16-bit unit. 8-bit unit access is disable. Figure 14.5 Composition of CRC register access related register Page 187 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION For accessing to CRC register data, set accessing address (CA3 to CA0) (shown in Table 14.3) to CRC register address control register (address 021216). Then write data (CD15 to CD0) by CRC register data control register (address 021416). When end the data accessing, CRC register address control register increments address automatically. Then, next address data writing is possible. CRC register access registers are shown in Figure 14.5, CRC register access block diagram is shown in Figure 14.6. The operation example of CRC operation circuit is shown in Figure 14.7. The example of program is shown in Figure 14.8, and CRC register bit compositions are shown in p191 to p199. Data bus (16-bit) (address 021216) (CA13 to CA8) (CA4) CRC register address control register (4) (CA3 to CA0) CRC register data control register (16) (CD15 to CD0) (address 021416) Increment automatically after data access Code data shift register Generator polynomial register Shift counter Shift control circuit 82 bit CRC operation circuit Error correction mode remainder polynomial register Error judging circuit (Majority circuit) CRC error detection register Figure 14.6 Access block diagram for CRC registers Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 188 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION b81 b0 (1) Reset of CRC remainder bit 0000000 *** 00000000 CRC register CRC_81 to 00 [address 0216 to 0716] CRC remainder bit is automatically reset by CRCON=0 (address control register for CRC registers). b15 b0 (2) Setting 0016 CRC register DAOUT [address 0016] After CRC operation end b81 b0 CRC register CRC_81 to 00 [address 0216 to 0716] The CRC code is stored The data set as the DAOUT register is shifted from the low rank side of CRC remainder bit one by one (b0). MOJURO-2 operation is operation that complies with the law given below. 0+0=0 0+1=1 1+0=1 1+1=0 -1 = 1 *** 1000 01 100 0011 0000 * * * 0001 0001 0000 0000 0000 0001 0000 0000 * * * 0000 0000 0000 * * * 0000 0000 1 0000 1100 * * * 0010 001 b0 b82 b81 1100 * * * 0010 0010 0000 1000 *** 0001 0001 *** Remainder b81 b0 Generator polynomial shown in below is used in this circuit : X82 + X77 + X76 + X71 + X67 + X66 + X52 + X48 + X40 + X36 + X34 + X24 + X22 + X18 + X10 + X4 + 1 Figure 14.7 Example of operation of CRC operation circuit Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 189 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION ; ; ; _CRC_ADRS _CRC_DATA SLICE_WORD_NUM ; ; ; _wait .macro nop nop nop .endm ; ; ; ;--------- Setting of generator polynomial mov.w _wait mov.w 0000110000100011B , _CRC_DATA #0008H ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------, _CRC_ADRS ; Set the head address of the generator polynomial register ; Wait ; Coefficient of generator polynomial 82nd to 66th ( x^77 +x~76 +x^71 +x^67 +x^66) CRC operation routine Macro definition .equ .equ .equ 00212h 00214h 17 ; SFR address of CRC register address control register ; SFR address of CRC register data control register ; Code data length (in nuits of word) Equations (Constant definition) ;------ Writing of code data ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------mov.w #0000H , _CRC_ADRS ; Initialization of CRC register address control register mov.w #9010H , _CRC_ADRS ; Set up of CRCON=1, CRCCHANGE=0, CRCLOOP=10H, Increment=ON, and CRC address=00H. mov.w L18: cmp.w jgeu lde.w add.w jmp L20: ; After finishing writing 272-bit code data, ; shift a bit for dummy surely in error correction mode. ; Specifying 1-bit is set up by CRCLOOP=01H. mov.w _wait mov.w #0000H , _CRC_DATA #8100H , _CRC_ADRS ; Set up of CRCON=1, CRCCHANGE=0, CRCLOOP=10H, Increment=OFF, and CRC address=00H. ; Wait ; Writing data to the code data shift register for dummy shift. #SLICE_WORD_NUM*2 L20 _CrcCodeData[A0] #0002H L18 , _CRC_DATA ,A0 , A0 #0000H , A0 ; Initialization of a loop variable (A0) ; Branch label ; Comparison of the loop variable ; Go to L20 if writing code data is finished. ; Writing code data to the code data shift register. ; Increment of the address storing code data. ; Return to the head of this loop. ; Branch label ;--------- Dummy shift --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ;--------- Error detection ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------; Since the address automatic increment in dummy shift (Increment=OFF), set CRC address=01H here. ; When accessing other CRC registers, the processing shown in the following two lines is necessary. ; ; mov.w _wait mov.w cmp.w jeq _CRC_DATA #0000H L16 , R0 , R0 #9001H , _CRC_ADRS ; Set up of CRCON=1, CRCCHANGE=0, CRCLOOP=10H, Incremet=OFF and CRC address=01H. ; Wait ; Read of CRC error detection register. ; Judgement of CRC error. ; In the case of R0=0, branch to L16 since CRC error has not occurred (CRC error correction is skipped). ;--------- Error correction --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------mov.w _wait mov.w L22: cmp.w jgeu lde.w jsr mov.w add.w jmp L24: #SLICE_WORD_NUB L24 _CrcCodeData[A0] _waitlong _CRC_DATA #0002H L22 , _CrcCodeData[A0] , A0 , _CRC_DATA , A0 #0000H , A0 #0D010H , _CRC_ADRS ; Set up of CRCON=1, CRCCHANGE=1, CRCLOOP=10H, Increment=ON and CRC address=00H. ; Wait ; Initialization of a loop variable (A0) ; Branch label ; Comparison of the loop variable ; Go to L24 if correction of error data is finished. ; Writing code data to the code data shift register. ; Wait for finish of error correction. ; Read of error correction data in the address storing code data. ; Increment of the address storing code data. ; Return to the head of this loop. ; Branch label ;------- The check of error correction data -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------mov.w _wait mov.w L16: ; ; The function sample for weight for error correction ; .align .glb _waitlong: rts _waitlong ; Function label _CRC_DATA , R0 #8111H , _CRC_ADRS ; Set up of CRCON=1, CRCCHANGE=0, CRCLOOP=10H, Increment=ON and CRC address=00H ; Wait ; Error check after error correction. R0=000H if correction is performed. Figure 14.8 Example of program Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 190 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 1.Bit composition of a CRC register 1. Address 0016 (=CA3 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol DAOUT0 DAOUT1 DAOUT2 DAOUT3 DAOUT4 DAOUT5 DAOUT6 DAOUT7 DAOUT8 DAOUT9 DAOUT10 DAOUT11 DAOUT12 DAOUT13 DAOUT14 DAOUT15 Bit name The code data shift register write-in bit 0 The code data shift register write-in bit 1 The code data shift register write-in bit 2 The code data shift register write-in bit 3 The code data shift register write-in bit 4 The code data shift register write-in bit 5 The code data shift register write-in bit 6 The code data shift register write-in bit 7 The code data shift register write-in bit 8 The code data shift register write-in bit 9 The code data shift register write-in bit 10 The code data shift register write-in bit 11 The code data shift register write-in bit 12 The code data shift register write-in bit 13 The code data shift register write-in bit 14 The code data shift register write-in bit 15 Function When write, data is written to "code data shift register" (Note). When read, data differs between in error detection mode and in error correction mode. * In error detection mode (CRCCHANGE=0) 000016 is read after shift end. When read during shift operation, its content is indeterminate. * In error correction mode (CRCCHANGE=1) Corrected data is read after the original data is written in and some interval of data shift. RW Note: Refer to Figure 14.16 Access block diagram for CRC registers. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 191 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 2. Address 0116 (=CA3 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol CRC_ERR00 Bit name The CRC bit 81 to 74 error detection bit The CRC bit 73 to 66 error detection bit The CRC bit 65 to 58 error detection bit The CRC bit 57 to 50 error detection bit The CRC bit 49 to 42 error detection bit The CRC bit 41 to 34 error detection bit The CRC bit 33 to 26 error detection bit The CRC bit 25 to 18 error detection bit The CRC bit 17 to 10 error detection bit The CRC bit 09 to 02 error detection bit The CRC bit 01 to 00 error detection bit Function Logical OR of the CRC remainder bits 81 to 74 (address 0216) Logical OR of the CRC remainder bits 73 to 66 (address 0216) Logical OR of the CRC remainder bits 65 to 58 (address 0316) Logical OR of the CRC remainder bits 57 to 50 (address 0316) Logical OR of the CRC remainder bits 49 to 42 (address 0416) Logical OR of the CRC remainder bits 41 to 34 (address 0416) Logical OR of the CRC remainder bits 33 to 26 (address 0516) Logical OR of the CRC remainder bits 25 to 18 (address 0516) Logical OR of the CRC remainder bits 17 to 10 (address 0616) Logical OR of the CRC remainder bits 09 to 02 (address 0616) Logical OR of the CRC remainder bits 01 to 00 (address 0716) RW CRC_ERR01 CRC_ ERR02 CRC_ERR03 CRC_ERR04 CRC_ERR05 CRC_ERR06 CRC_ERR07 CRC_ERR08 CRC_ERR09 CRC_ERR10 Nothing is assigned. The value is "0" when it reads. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 192 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. Address 0216 (=CA3 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol CRC_81 CRC_80 CRC_79 CRC_78 CRC_77 CRC_76 CRC_75 CRC_74 CRC_73 CRC_72 CRC_71 CRC_70 CRC_69 CRC_68 CRC_67 CRC_66 Bit name 81th remainder polynomial coefficient bit 80th remainder polynomial coefficient bit 79th remainder polynomial coefficient bit 78th remainder polynomial coefficient bit 77th remainder polynomial coefficient bit 76th remainder polynomial coefficient bit 75th remainder polynomial coefficient bit 74th remainder polynomial coefficient bit 73th remainder polynomial coefficient bit 72th remainder polynomial coefficient bit 71th remainder polynomial coefficient bit 70th remainder polynomial coefficient bit 69th remainder polynomial coefficient bit 68th remainder polynomial coefficient bit 67th remainder polynomial coefficient bit 66th remainder polynomial coefficient bit Function The coefficient of each degree of a remainder polynomial is set up. It is shown in below when a remainder polynomial is made into CRC_MOD. CRC_MOD = CRC_n * X n=0 81 n RW Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 193 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 4. Address 0316 (=CA3 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol CRC_65 CRC_64 CRC_63 CRC_62 CRC_61 CRC_60 CRC_59 CRC_58 CRC_57 CRC_56 CRC_55 CRC_54 CRC_53 CRC_52 CRC_51 CRC_50 Bit name 65th remainder polynomial coefficient bit 64th remainder polynomial coefficient bit 63th remainder polynomial coefficient bit 62th remainder polynomial coefficient bit 61th remainder polynomial coefficient bit 60th remainder polynomial coefficient bit 59th remainder polynomial coefficient bit 58th remainder polynomial coefficient bit 57th remainder polynomial coefficient bit 56th remainder polynomial coefficient bit 55th remainder polynomial coefficient bit 54th remainder polynomial coefficient bit 53th remainder polynomial coefficient bit 52th remainder polynomial coefficient bit 51th remainder polynomial coefficient bit 50th remainder polynomial coefficient bit Function Refer to CRC_81 to 66 (address 0216). RW Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 194 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 5. Address 0416 (=CA3 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol CRC_49 CRC_48 CRC_47 CRC_46 CRC_45 CRC_44 CRC_43 CRC_42 CRC_41 CRC_40 CRC_39 CRC_38 CRC_37 CRC_36 CRC_35 CRC_34 Bit name 49th remainder polynomial coefficient bit 48th remainder polynomial coefficient bit 47th remainder polynomial coefficient bit 46th remainder polynomial coefficient bit 45th remainder polynomial coefficient bit 44th remainder polynomial coefficient bit 43th remainder polynomial coefficient bit 42th remainder polynomial coefficient bit 41th remainder polynomial coefficient bit 40th remainder polynomial coefficient bit 39th remainder polynomial coefficient bit 38th remainder polynomial coefficient bit 37th remainder polynomial coefficient bit 36th remainder polynomial coefficient bit 35th remainder polynomial coefficient bit 34th remainder polynomial coefficient bit Function Refer to CRC_81 to 66 (address 0216). RW Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 195 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. Address 0516 (=CA3 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol CRC_33 CRC_32 CRC_31 CRC_30 CRC_29 CRC_28 CRC_27 CRC_26 CRC_25 CRC_24 CRC_23 CRC_22 CRC_21 CRC_20 CRC_19 CRC_18 Bit name 33th remainder polynomial coefficient bit 32th remainder polynomial coefficient bit 31th remainder polynomial coefficient bit 30th remainder polynomial coefficient bit 29th remainder polynomial coefficient bit 28th remainder polynomial coefficient bit 27th remainder polynomial coefficient bit 26th remainder polynomial coefficient bit 25th remainder polynomial coefficient bit 24th remainder polynomial coefficient bit 23th remainder polynomial coefficient bit 22th remainder polynomial coefficient bit 21th remainder polynomial coefficient bit 20th remainder polynomial coefficient bit 19th remainder polynomial coefficient bit 18th remainder polynomial coefficient bit Function Refer to CRC_81 to 66 (address 0216). RW Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 196 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 7. Address 0616 (=CA3 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol CRC_17 CRC_16 CRC_15 CRC_14 CRC_13 CRC_12 CRC_11 CRC_10 CRC_09 CRC_08 CRC_07 CRC_06 CRC_05 CRC_04 CRC_03 CRC_02 Bit name 17th remainder polynomial coefficient bit 16th remainder polynomial coefficient bit 15th remainder polynomial coefficient bit 14th remainder polynomial coefficient bit 13th remainder polynomial coefficient bit 12th remainder polynomial coefficient bit 11th remainder polynomial coefficient bit 10th remainder polynomial coefficient bit 09th remainder polynomial coefficient bit 08th remainder polynomial coefficient bit 07th remainder polynomial coefficient bit 06th remainder polynomial coefficient bit 05th remainder polynomial coefficient bit 04th remainder polynomial coefficient bit 03rd remainder polynomial coefficient bit 02nd remainder polynomial coefficient bit Function Refer to CRC_81 to 66 (address 0216). RW 8. Address 0716 (=CA3 to 0) CD15 CD8CD7 CD0 Bit symbol CRC_01 CRC_00 Bit name 01st remainder polynomial coefficient bit 00th remainder polynomial coefficient bit Nothing is assigned. The value is "0" when it reads. Function Refer to CRC_81 to 66 (address 0216). RW Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 197 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. Address 0816 (=CA3 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol Bit name Function The coefficient of each degree of the generation polynomial is set. The coefficient from 81 to the 66th is set for 82 bit CRC mode. The 15th in case of 16 bit CRC mode. The 0th coefficients are set. RW REG_C0 REG_C1 REG_C2 REG_C3 REG_C4 REG_C5 REG_C6 REG_C7 REG_C8 REG_C9 REG_C10 REG_C11 REG_C12 REG_C13 REG_C14 REG_C15 Coefficient bit of the 66/0th generation polynomials Coefficient bit of the 67/1th generation polynomials Coefficient bit of the 68/2th generation polynomials Coefficient bit of the 69/3th generation polynomials Coefficient bit of the 70/4th generation polynomials Coefficient bit of the 71/5th generation polynomials Coefficient bit of the 72/6th generation polynomials Coefficient bit of the 73/7th generation polynomials Coefficient bit of the 74/8th generation polynomials Coefficient bit of the 75/9th generation polynomials Coefficient bit of the 76/10th generation polynomials Coefficient bit of the 77/11th generation polynomials Coefficient bit of the 78/12th generation polynomials Coefficient bit of the 79/13th generation polynomials Coefficient bit of the 80/14th generation polynomials Coefficient bit of the 81/15th generation polynomials When generation polynomial to be CRC_GP, CRC_GP = X 15 n=0 82 n+66 REG_Cn * X +X +X +X 56 36 18 +X +X +X 52 34 10 +X +X 48 24 4 +X +X 40 22 +X +1 (For 82 bit CRC mode) 16 CRC_GP = X + RE6_Cn * X n=0 15 n (For 16 bit CRC mode) 10. Address 0916 (=CA3 to 0) CD15 CD8CD7 CD0 Bit symbol Bit name Function RW Nothing is assigned. The value is unfixed when it reads. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 198 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. Address 0A16 (=CA3 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol Bit name Function RW Nothing is assigned. The value is unfixed when it reads. 12. Address 0B16 (=CA3 to 0) CD15 CD8CD7 CD0 Bit symbol Bit name Function RW Nothing is assigned. The value is unfixed when it reads. 13. Address 0C16 (=CA3 to 0) CD15 CD8CD7 CD0 Bit symbol Bit name Function RW Nothing is assigned. The value is unfixed when it reads. 14. Address 0D16 (=CA3 to 0) CD15 CD8CD7 CD0 0000 Bit symbol Bit name Function RW Reserved bit CRC16SEL CRC mode select bit Must set to "0." Selects 82 bit CRC/16 bit CRC mode CRC16SEL 0 1 CRC mode 82 bit CRC 16 bit CRC Nothing is assigned Indeterminate at reading Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 199 of 326 DA5 to DA0 DD11 DD10 DD9 DD7 LN7_EV0 LN7_EV1 LN17_OD0 LN16_OD0 _ _ LN5_OD0 LN5_OD1 _ FLC5 CHK_FLC5 SEKI5 SLS_HP5 _ _ SLS3 SLS2 SLS1 SLS0 _ FLC0 CHK_FLC0 SEKI0 SLS_HP0 _ SLS0 _ FLC0 CHK_FLC0 SEKI0 SLS_HP0 _ SLS1 _ _ _ _ _ _ _ _ DIV_PDC0 DIV_VPS0 _ _ DIVP_CK3 DLYSEL3 _ VPS_VP4 MASK4 _ PLSPOS5 PLSNEG5 HCOUNT5 _ _ _ RMTHD0(6) RMTHD1(6) _ HINT_LINE7 INTRMT3 _ _ RTCON MINOUT8 DAYCUONT8 RMT_TM(0) RMT_TMH(0) _ _ _ _ _ MINOUT7 DAYCUONT7 RMTDIV(1) RMT_TML(7) _ _ _ HINT_LINE6 INTRMT2 _ _ _ MINOUT6 DAYCUONT6 RMTDIV(0) RMT_TML(6) _ _ _ _ RMTHD0(5) RMTHD1(5) _ HINT_LINE5 INTRMT1 YUKOU0(5) _ SECOUT5 MINOUT5 DAYCUONT5 RMCDIV(1) RMT_TML(5) _ _ _ PLSPOS4 PLSNEG4 HCOUNT4 _ _ _ RMTHD0(4) RMTHD1(4) _ HINT_LINE4 INTRMT0 YUKOU0(4) _ SECOUT4 MINOUT4 DAYCUONT4 RMCDIV(0) RMT_TML(4) _ _ 6BITOFF VPS_VP3 MASK3 _ PLSPOS3 PLSNEG3 HCOUNT3 _ _ _ RMTHD0(3) RMTHD1(3) _ HINT_LINE3 VINT3 YUKOU0(3) _ SECOUT3 MINOUT3 DAYCUONT3 IRPOL(2) RMT_TML(3) RMTTXINT(3) _ DIV_PDCS2 DIV_VPSS2 _ _ DIVP_CK2 DLYSEL2 _ VPS_VP2 MASK2 _ PLSPOS2 PLSNEG2 HCOUNT2 _ _ _ RMTHD0(2) RMTHD1(2) _ HINT_LINE2 VINT2 YUKOU0(2) _ SECOUT2 MINOUT2 DAYCUONT2 IRPOL(1) RMT_TML(2) RMTTXINT(2) _ _ _ _ _ DIV_PDCS1 DIV_VPSS1 _ ADON_TIM DIVP_CK1 DLYSEL1 START VPS_VP1 MASK1 _ PLSPOS1 PLSNEG1 HCOUNT1 _ _ _ RMTHD0(1) RMTHD1(1) _ HINT_LINE1 VINT1 YUKOU0(1) _ SECOUT1 MINOUT1 DAYCUONT1 IRPOL(0) RMT_TML(1) RMTTXINT(1) _ _ SLS0 _ _ _ _ _ _ _ DIV_PDCS0 DIV_VPSS0 _ ADSEL DIVP_CK0 DLYSEL0 ADLAT VPS_VP0 MASK0 _ PLSPOS0 PLSNEG0 HCOUNT0 _ _ _ RMTHD0(0) RMTHD1(0) _ HINT_LINE0 VINT0 YUKOU0(0) _ SECOUT0 MINOUT0 DAYCUONT0 RMTSTART RMT_TML(0) RMTTXINT(0) _ for read for read for read Status register 3 Status register 2 _ FLC1 CHK_FLC1 SEKI1 SLS_HP1 _ SLS1 _ FLC1 CHK_FLC1 SEKI1 SLS_HP1 _ FLC2 CHK_FLC2 SEKI2 SLS_HP2 _ SLS2 _ FLC2 CHK_FLC2 SEKI2 SLS_HP2 _ SLS2 _ _ _ _ FLC3 CHK_FLC3 SEKI3 SLS_HP3 _ SLS3 _ FLC3 CHK_FLC3 SEKI3 SLS_HP3 _ SLS3 _ _ _ _ _ _ _ _ _ SLS5 _ FLC5 CHK_FLC5 SEKI5 SLS_HP5 _ SLS5 _ FLC5 CHK_FLC5 SEKI5 SLS_HP5 _ SLS5 _ _ _ _ _ FLD1V _ _ DIV_PDC1 DIV_VPS1 _ SLION_TIM DIVP_CK4 DLYSEL4 _ _ DIV_PDC2 DIV_VPS2 _ _ DIVP_CK5 DLYSEL5 SYNLVL0 VPS_VP5 MASK5 _ _ _ _ SLS4 _ SLS_HP4 SEKI4 CHK_FLC4 FLC4 _ SLS4 _ SLS_HP4 SEKI4 CHK_FLC4 FLC4 _ SLS4 _ SLS_HP4 SLS_HP3 SLS_HP2 SLS_HP1 SLS_HP0 SEKI4 SEKI3 SEKI2 SEKI1 SEKI0 Status register 1 CHK_FLC4 CHK_FLC3 CHK_FLC2 CHK_FLC1 CHK_FLC0 FLC4 FLC3 FLC2 FLC1 FLC0 _ _ _ _ _ LN4_OD1 LN3_OD1 LN2_OD1 LN1_OD1 LN0_OD1 LN4_OD0 LN3_OD0 LN2_OD0 LN1_OD0 LN0_OD0 _ _ _ _ _ Line register _ _ _ _ _ LN16_OD1 LN6_OD0 LN6_OD1 _ FLC6 CHK_FLC6 SEKI6 SLS_HP6 _ SLS6 _ FLC6 CHK_FLC6 SEKI6 SLS_HP6 _ SLS6 _ FLC6 CHK_FLC6 SEKI6 SLS_HP6 _ SLS6 _ _ PDC_VCO_ON _ _ SEPV0 _ DIV_PDC3 DIV_VPS3 _ _ DIVP_CK6 DLYSEL6 SYNLVL1 VPS_VP6 MASK6 _ PLSPOS6 PLSNEG6 HCOUNT6 _ LN17_OD1 LN7_OD0 LN7_OD1 _ FLC7 CHK_FLC7 SEKI7 SLS_HP7 _ SLS7 _ FLC7 CHK_FLC7 SEKI7 SLS_HP7 _ SLS7 _ FLC7 CHK_FLC7 SEKI7 SLS_HP7 _ SLS7 _ _ PDC_VCO_R0 _ MACRO_ON _ _ DIV_PDC4 DIV_VPS4 _ _ DIVP_CK7 DLYSEL7 SYNLVL2 VPS_VP7 MASK7 _ PLSPOS7 PLSNEG7 HCOUNT7 _ _ _ RMTHD0(7) RMTHD1(7) LN6_EV1 LN5_EV1 LN4_EV1 LN3_EV1 LN2_EV1 LN1_EV1 LN0_EV1 LN6_EV0 LN5_EV0 LN4_EV0 LN3_EV0 LN2_EV0 LN1_EV0 LN0_EV0 DD5 LN9_EV0 LN9_EV1 _ _ LN9_OD0 LN9_OD1 _ _ FLC8 CHK_FLC8 _ GET_HP0 _ _ _ FLC8 CHK_FLC8 _ GET_HP0 _ _ _ FLC8 CHK_FLC8 _ GET_HP0 _ _ _ _ PDC_VCO_R1 _ _ NORMAL _ DIV_PDC5 DIV_VPS5 _ _ DIVV_CK0 WEIGHT0 ADON VPS_VP8 _ _ PLSPOS8 PLSNEG8 HCOUNT8 _ _ _ RMTHD0(8) RMTHD1(8) _ HINT_LINE8 HINT0 YUKOU1(0) FLC9 CHK_FLC9 SLSLVL0 GET_HP1 _ _ _ FLC9 CHK_FLC9 SLSLVL0 GET_HP1 _ _ _ FLC9 CHK_FLC9 SLSLVL0 GET_HP1 _ _ _ _ VPS_VCO_ON _ _ LEVELA _ DIV_PDC6 DIV_VPS6 _ _ DIVV_CK1 WEIGHT1 INTAD SLI_GO _ _ _ _ HCOUNT9 _ _ _ JSTCKDIV0 FILDIV0 _ PTC8 HINT1 YUKOU1(1) _ _ MINOUT9 DAYCUONT9 RMT_TM(1) RMT_TMH(1) _ LN8_OD1 LN8_OD0 _ _ LN8_EV1 LN8_EV0 LN10_EV0 LN10_EV1 _ _ LN10_OD0 LN10_OD1 _ FLC10 CHK_FLC10 SLSLVL1 _ _ _ _ FLC10 CHK_FLC10 SLSLVL1 _ _ _ _ FLC10 CHK_FLC10 SLSLVL1 _ _ _ _ _ _ _ _ _ _ DIV_PDC7 DIV_VPS7 _ _ DIVV_CK2 WEIGHT2 INTDA _ _ _ _ HCOUNT10 _ _ _ JSTCKDIV1 _ _ PTD8 HINT2 YUKOU1(2) _ _ MINOUT10 DAYCUONT10 RMT_TM(2) RMT_TMH(2) _ _ LN11_EV0 LN11_EV1 _ _ LN11_OD0 LN11_OD1 _ FLC11 CHK_FLC11 BIFON _ _ _ _ FLC11 CHK_FLC11 BIFON _ _ _ _ FLC11 CHK_FLC11 BIFON _ _ _ _ _ _ _ _ _ _ DIV_PDC8 DIV_VPS8 _ _ DIVV_CK3 WEIGHT3 _ STBSYNCSEP SYNCSEP_ON0 _ _ _ _ HCOUNT11 _ _ _ JSTCKON FILDIV0 _ _ HINT3 YUKOU1(3) _ _ _ DAYCUONT11 RMT_TM(3) RMT_TMH(3) _ _ DD8 DD4 DD3 DD2 DD1 DD0 Remarks DD6 DD15 DD14 DD13 DD12 14.5 0016 LN15_EV0 LN14_EV0 LN13_EV0 LN12_EV0 0116 LN15_EV1 LN14_EV1 LN13_EV1 LN12_EV1 0216 LN17_EV0 LN16_EV0 _ _ 0316 LN17_EV1 LN16_EV1 _ _ Table 14.4 0416 LN15_OD0 LN14_OD0 LN13_OD0 LN12_OD0 0516 LN15_OD1 LN14_OD1 LN13_OD1 LN12_OD1 0616 DIVS1 DIVS0 SELVCO _ 0716 FLC15 FLC14 FLC13 FLC12 0816 CHK_FLC15 CHK_FLC14 CHK_FLC13 CHK_FLC12 0916 _ _ _ _ 0A16 GETPEEK3 GETPEEK2 GETPEEK1 GETPEEK0 M306H7MG-XXXFP/MC-XXXFP/FGFP Rev.2.10 Oct 25, 2006 REJ03B0152-0210 0B16 _ FRAM _ _ 0C16 _ GSTTIM SELSTART _ 0D16 DIVS1 DIVS0 SELVCO _ 0E16 FLC15 FLC14 FLC13 FLC12 0F16 CHK_FLC15 CHK_FLC14 CHK_FLC13 CHK_FLC12 1016 _ _ _ _ 1116 GETPEEK3 GETPEEK2 GETPEEK1 GETPEEK0 Expansion Register 1216 _ FRAM _ _ 1316 _ GSTTIM SELSTART _ 1416 DIVS1 DIVS0 SELVCO _ 1516 FLC15 FLC14 FLC13 FLC12 1616 CHK_FLC15 CHK_FLC14 CHK_FLC13 CHK_FLC12 1716 _ _ _ _ Expansion register composition Control Data slice function. Expansion register composition is shown in Table 14.4. Page 200 of 326 _ 1816 GETPEEK3 GETPEEK2 GETPEEK1 GETPEEK0 1916 _ FRAM _ _ 1A16 _ GSTTIM SELSTART _ 1B16 _ _ _ _ 1C16 ADSTART _ EXT_PDC2 _ 1D16 _ _ _ _ 1E16 _ _ _ _ 1F16 _ _ _ _ 2016 _ MPAL NXP _ 2116 _ _ _ _ 2216 HM84SEL _ _ _ 2316 _ _ _ HORAX_ON 2416 _ _ _ _ 2516 _ _ _ _ 2616 DIVV_CK7 DIVV_CK6 DIVV_CK5 DIVV_CK4 2716 _ _ _ WEIGHT4 2816 _ _ _ _ 2916 _ _ _ _ 2A16 _ _ _ _ 2B16 SEL_PDEC _ SEL_VPSH SEL_PDCH 2C16 _ _ _ _ 2D16 _ _ _ _ 2E16 HCOUNT15 HCOUNT14 HCOUNT13 HCOUNT12 2F16 STB_RES _ _ _ 3016 _ _ _ _ 3116 _ _ _ _ 3216 RMTSEL _ _ _ 3316 FILDIV1(1) FILDIV1(0) _ VERTX 3416 _ _ _ _ 3516 EXAOFF _ _ _ 3616 SECINT3 SECINT2 SECINT1 SECINT0 3716 _ _ YUKOU1(5) YUKOU1(4) 3816 _ _ _ _ 3916 SECJUST _ _ _ 3A16 _ _ _ _ 3B16 DAYCUONT15 DAYCUONT14 DAYCUONT13 DAYCUONT12 3C16 RMT_TM(7) RMT_TM(6) RMT_TM(5) RMT_TM(4) 3D16 3E16 RMT_TMH(7) _ RMT_TMH(6) IROUT_SLICEON RMT_TMH(5) _ RMT_TMH(4) _ 14. EXPANSION FUNCTION 3F16 _ _ _ M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION For accessing to expansion register data, set accessing address (DA5 to DA0) (shown in Table 14.4) to expansion register address control register (address 021616). Then write data (DD15 to DD0) to expansion register data control register (address 021816). When end the data accessing, expansion register address control register increments address automatically. Then, next address data writing is possible. After reset, the value of expansion register become "0" all, except for the clock timer. Expansion register access registers are shown in Figure 14.9, expansion register access block diagram is shown in Figure 14.10, and expansion register bit compositions are shown in p202 to p239. Expansion register address control register b1 5 b8 b7 b6 b0 Symbol DA Address 021616 When reset 000016 Function Specify accessing expansion register address Nothing is assigned. When write, set to "0". When read, its content is indeterminate. Setting possible value 0016 to 4516 RW Expansion register address automatic increment 0:enable / 1:disable (Note2) Nothing is assigned. In an attempt to write to these bits, write "0". The value, if read, turns out to be indeterminated. Note1 : When access to expansion register, must be set expansion register address at first, then use expansion register data control register (021816). Note2 : When bit 8 = "0" setting, expansion register data control register increments by accessing expansion register data control register, so it is not necessary to setting the next expansion register address. When bit 8 = "1" setting, the address is fixed. Expansion register data control register b1 5 b8 b7 b0 Symbol DD Address 021816 When reset 000016 Function Write and read out the data of expansion register which is specified by expansion register address control register (address 021616) Setting possible value 000016 to FFFF16 RW Note : Data access must be 16-bit unit. 8-bit unit access is disable. Figure 14.9 Expansion register access registers composition Data bus (16-bit) (address 021616) (DA8) Expansion register address control register (6) (DA5 to DA0) Expansion register data control register (16) (DD15 to DD0) (address 021816) Increment automatically after data access Expansion register Figure 14.10 Expansion register access block diagram Page 201 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP Bit composition of an expansion register 1. Address 0016 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol LN0_EV0 LN1_EV0 LN2_EV0 LN3_EV0 LN4_EV0 LN5_EV0 LN6_EV0 LN7_EV0 LN8_EV0 LN9_EV0 LN10_EV0 LN11_EV0 LN12_EV0 LN13_EV0 LN14_EV0 LN15_EV0 Bit name The 0th line state register selection bit The 1st line state register selection bit The 2nd line state register selection bit The 3rd line state register selection bit The 4th line state register selection bit The 5th line state register selection bit The 6th line state register selection bit The 7th line state register selection bit The 8th line state register selection bit The 9th line state register selection bit The 10th line state register selection bit The 11th line state register selection bit The 12th line state register selection bit The 13th line state register selection bit The 14th line state register selection bit The 15th line state register selection bit Function As for the slicing method of the n-th line (Notes 1), it is chosen which set of the state register settings of the three sets (Notes 2) is used with the combination of LNn_EV0 (address 0016 and 0216, n = 0 to 17) and LNn_EV1 (address 0116 and 0316, n= 0 to 17.) Four kinds of following state registers can be chosen for every line (Notes 3.) LNn_EV1 LNn_EV0 State register(Notes 2) Do not set up 0 0 State register 1 1 0 State register 2 0 1 State register 3 1 1 RW Notes 1. The n-th line: The number of lines after a slice start. Please refer to the supplement (3) of 15.6 expansion register composition (P229) for details. Notes 2. 06h to 0Ch address: State register 1 0Dh to 13h address: State register 2 14h to 1Ah address: State register 3 Notes 3. The example of a setting. V after sync separation The 0th line The 1st line The 2nd line H after sync separation line 1 line 2 *** line n line (n+1) line (n+2) LN0_EV1=0 LN1_EV1=0 LN2_EV1=1 LN0_EV0=1 LN1_EV0=1 LN2_EV0=0 slice slice slice processing by processing by processing by setup of the setup of the setup of the state register 1. state register 1. state register 2. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 202 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 2. Address 0116 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol LN0_EV1 LN1_EV1 LN2_EV1 LN3_EV1 LN4_EV1 LN5_EV1 LN6_EV1 LN7_EV1 LN8_EV1 LN9_EV1 LN10_EV1 LN11_EV1 LN12_EV1 LN13_EV1 LN14_EV1 LN15_EV1 Bit name The 0th line state register selection bit The 1st line state register selection bit The 2nd line state register selection bit The 3rd line state register selection bit The 4th line state register selection bit The 5th line state register selection bit The 6th line state register selection bit The 7th line state register selection bit The 8th line state register selection bit The 9th line state register selection bit The 10th line state register selection bit The 11th line state register selection bit The 12th line state register selection bit The 13th line state register selection bit The 14th line state register selection bit The 15th line state register selection bit Function Refer to LNn_EV0 (address 0016) RW Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 203 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 3. Address 0216 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol Nothing is assigned. Bit name Function RW xx Refer to LNn_OD0 (address 0416) LN16_OD0 LN17_OD0 The 16th line state register selection bit The 17th line state register selection bit Nothing is assigned. LN16_EV0 LN17_EV0 The 16th line state register selection bit The 17th line state register selection bit xx Refer to LNn_EV0 (address 0016) 4. Address 0316 (=DA5 to 0) DD15 DD8DD7 DD0 Bit symbol Nothing is assigned. Bit name Function RW xx Refer to LNn_OD0 (address 0416) LN16_OD1 LN17_OD1 The 16th line state register selection bit The 17th line state register selection bit Nothing is assigned. LN16_EV1 LN17_EV1 The 16th line state register selection bit The 17th line state register selection bit xx Refer to LNn_EV0 (address 0016) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 204 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 5. Address 0416 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol LN0_OD0 LN1_OD0 LN2_OD0 LN3_OD0 LN4_OD0 LN5_OD0 LN6_OD0 LN7_OD0 LN8_OD0 LN9_OD0 LN10_OD0 LN11_OD0 LN12_OD0 LN13_OD0 LN14_OD0 LN15_OD0 Bit name The 0th line state register selection bit The 1st line state register selection bit The 2nd line state register selection bit The 3rd line state register selection bit The 4th line state register selection bit The 5th line state register selection bit The 6th line state register selection bit The 7th line state register selection bit The 8th line state register selection bit The 9th line state register selection bit The 10th line state register selection bit The 11th line state register selection bit The 12th line state register selection bit The 13th line state register selection bit The 14th line state register selection bit The 15th line state register selection bit Function As for the slicing method of the n-th line (Notes 1), it is chosen which set of the state register settings of the three sets (Notes 2) is used with the combination of LNn_OD0 (address 0416 and 0216, n = 0 to 17) and LNn_OD1 (address 0516 and 0316, n= 0 to 17.) Four kinds of following state registers can be chosen for every line. (Notes 3) LNn_EV1 LNn_EV0 State register(Notes 2) Do not set up 0 0 State register 1 1 0 State register 2 0 1 State register 3 1 1 RW Notes 1. The n-th line: The number of lines after a slice start. Please refer to the supplement (3) of 14.6 expansion register composition for details. Notes 2. 06h to 0Ch address: State register 1 0Dh to 13h address: State register 2 14h to 1Ah address: State register 3 Notes 3. The example of a setting. V after sync separation The 0th line The 1st line The 2nd line H after sync separation line 1 line 2 *** line n line (n+1) line (n+2) LN0_OD1=0 LN1_OD1=0 LN2_OD1=1 LN0_OD0=1 LN1_OD0=1 LN2_OD0=0 slice slice slice processing by processing by processing by setup of the setup of the setup of the state register 1. state register 1. state register 2. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 205 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 6. Address 0516 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol LN0_OD1 LN1_OD1 LN2_OD1 LN3_OD1 LN4_OD1 LN5_OD1 LN6_OD1 LN7_OD1 LN8_OD1 LN9_OD1 LN10_OD1 LN11_OD1 LN12_OD1 LN13_OD1 LN14_OD1 LN15_OD1 Bit name The 0th line state register selection bit The 1st line state register selection bit The 2nd line state register selection bit The 3rd line state register selection bit The 4th line state register selection bit The 5th line state register selection bit The 6th line state register selection bit The 7th line state register selection bit The 8th line state register selection bit The 9th line state register selection bit The 10th line state register selection bit The 11th line state register selection bit The 12th line state register selection bit The 13th line state register selection bit The 14th line state register selection bit The 15th line state register selection bit Function Refer to LNn_OD0 (address 0416) RW Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 206 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 7. Address 0616, 0D16, 1416 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 1100000000 Bit symbol Reserved bits Bit name Function Must set to "0." RW x x xx Reserved bits Must set to "1." Nothing is assigned. The PLL selection bit for slice 0 1 PDC VPS DIVS1 0 0 1 1 DIVS0 0 1 0 1 divided value no division divided by 2 divided by 3 divided by 5 SELVCO DIVS0 DIVS1 The clock division bit for slice 8. Address 0716, 0E16, 1516 (=DA5 to 0) DD15 DD8DD7 DD0 Bit symbol FLC0 FLC1 FLC2 FLC3 FLC4 FLC5 FLC6 FLC7 FLC8 FLC9 FLC10 FLC11 FLC12 FLC13 FLC14 FLC15 Bit name Framing code selection bit Function Framing code is set up Clock run-in Framing code Setup Data RW FLC0 to FLC15 16 bits are checked at maximum. However, the bit of CHK_FLCn (addresses 0816, 0F16 and 1616) = "1" is not checked. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 207 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 9. Address 0816, 0F16, 1616 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol CHK_FLC0 CHK_FLC1 CHK_FLC2 CHK_FLC3 CHK_FLC4 CHK_FLC5 CHK_FLC6 CHK_FLC7 CHK_FLC8 CHK_FLC9 CHK_FLC10 CHK_FLC11 CHK_FLC12 CHK_FLC13 CHK_FLC14 CHK_FLC15 Bit name Framing code check selection bit Function When acquiring data, it sets up whether framing code set up by FLC 0 to 15 (addresses 0716, 0E16, and 1516) is checked or not per bit. Data will be acquired if the n-th bit which is set as check is in agreement. RW CHK_FLCn 0 1 n-th bit check No check Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 208 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 10. Address 0916, 1016, 1716 (=DA5 to 0) DD15 01 10 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol SEKI0 Bit name Data slicer control bit 1 Function N SEKI1 SEKI0 5 (Note1) 0 0 4 (Note2) 1 0 6 (Note3) 0 1 8 (Note4) 1 1 N-times the digital value after SEKI7.6. RW SEKI1 SEKI2 Data slicer control bit 2 SEKI3 SEKI4 Data slicer control bit 3 SEKI5 N SEKI2 4 0 0 3 0 1 1 1 0 No differentiation 1 1 It differentiates from the digitized data in front of N/8 cycles (clock run-in cycle) to the digital value after SEKI0 and 1. N SEKI5 SEKI4 4 0 0 3 1 0 1 0 1 No differentiation 1 1 It differentiates from the digitized data in after N/8 cycles (clock run-in cycle) to the digital value after SEKI3 and 2. SEKI3 SEKI6 Leveling existence of the following A-D convert value Average for four clocks It doesn't level The differentiation by SEKI2, 3, SEKI4, and 5 is differentiated by one time the value. SEKI6 Data slicer control bit 4 0 1 0 SEKI7 Data slicer control bit 5 1 The differentiation by SEKI2, 3, SEKI4, and 5 is differentiated by twice the value. Nothing is assigned. 0 SISLVL0 Slice level control bit 1 SISLVL1 BIFON Slice level measurement period selection bit Data format selection bit 0 1 0 1 The clock line average level is used The slice level selection bit (0C16,1316, 1A16, and house number SLS7?0) is used. 2 cycles of Clock run-in 4 cycles of Clock run-in Non Return Zero Bi-phase type Reserved bit Must set to "0." Reserved bits Reserved bit Must set to "1." Must set to "0." Note 1. When selecting 5 times with SEKI0, 1 and twice with SEKI7, select "none" for any one of SEKI2, 3 or SEKI4, 5. Note 2. When selecting 8 times for SEKI0, 1, select "none" for both SEKI2, 3 and SEKI4, 5. Note 3. When selecting 6 times for SEKI0, 1 and twice for SEKI7, select "none" for any one of SEKI2, 3 or SEKI4, 5. Note 4. When selecting "none" for both SEKI2, 3 and SEKI4, 5, do not select 4 times, and select 8 times for SEKI0, 1. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 209 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 11. Address 0A16, 1116, 1816 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 01 Bit symbol SLS_HP0 SLS_HP1 SLS_HP2 SLS_HP3 SLS_HP4 SLS_HP5 The position where framing code begins to be checked is set up. SLS_HP6 SLS_HP7 GET_HP0 GET_HP1 Reserved bit Bit name Slice check start position selection bit Function It will become below if data slice start position is made into SLS_HS. SLS_HS = T2x2n SLS_HPn n=0 7 RW T2 : Clock run-in cycle /2 Setup in a 1-bit unit is possible. Phase fine-tuning bit Slice data 0/1 judging clock is tuned finely. Must set to "1." 5 5 Clock run-in period 2 4 5 6 Reserved bit GETPEEK0 GETPEEK1 GETPEEK2 GETPEEK3 Peak detection period selection bit 0 Peak detection period selection bit 1 Peak detection period selection bit 2 Peak detection period selection bit 3 0 1 0 1 Must set to "0." GETPEEK1 GETPEEK0 0 0 1 1 0 1 0 1 With clock compensation With no clock compensation Only a mountain is detected. A mountain and a valley are detected. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 210 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 12. Address 0B16, 1216, 1916 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 0 Bit symbol Nothing is assigned. Reserved bit The number selection bit of framing code check bits Bit name Function RW XX Must set to "0." 0 1 15-bit check 16-bit check XX X FRAM Nothing is assigned. 13. Address 0C16, 1316, 1A16 (=DA5 to 0) DD15 DD8DD7 DD0 0 00000 Bit symbol SLS0 SLS1 SLS2 Data Bit name Slice level selection bit Function It will become below if a slice level is made into SLS_LVL. SLS_LVL RW SLS3 At the time of SLS7 = "H" SLS4 SLS5 At the time of SLS7 = "L" SLS6 SLS7 SLS_LVL = 2n SLSn n=0 6 SLS_LVL = 2n SLSn - 128 n=0 6 Reserved bits SELSTART Slice start condition selection bit Must set to "0." Slice beginning after slice check period 0 (SLS_HP7 to 0 of addresses 0A,11 and 18) passes Slice beginning after standing up of clock 1 run-in after slice check period (SLS_HP7 to 0 of addresses 0A,11 and 18) passes x GSTTIM Ghost correct control bit 0 Ghost correct OFF 1 Ghost correct ON Reserved bit Must set to "0." x Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 211 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. Address 1B16 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 000 000001000000 Bit symbol Reserved bits Bit name Function Must set to "0." RW x x x xx Reserved bit Must set to "1." Reserved bits Must set to "0." Nothing is assigned. Reserved bits Must set to "0." x 15. Address 1C16 (=DA5 to 0) DD15 DD8DD7 DD0 0 00000 0000000 Bit symbol Reserved bits Reserved bit Bit name Function Must set to "0." Must set to "1" when EPG-J is acquired. Otherwise, set to "0." Must set to "0." 0 1 no divided divided-in-3 X RW X X X Reserved bits EXT_PDC2 Selection of PLL divided-in-3 frequency bit for PDC Reserved bit Must set to "0." 0 1 Conversion completion Under conversion ADSTART A/D conversion completion bit Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 212 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. Address 1D16 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 00000 000 Bit symbol Nothing is assigned. Bit name Function RW xx Must set to "0." 0 1 PDC clock stop PDC clock oscillation Reserved bits PDC_VCO_ON x PDC clock oscillation selection bit PDC clock oscillation change bit PDC_VCO_R0 PDC_VCO_R1 PDC_VCO PDC_VCO _R1 _R0 0 0 0 1 1 0 1 1 0 1 Select PDC clock Select EPG-J clock Do not set up Do not set up x VPS_VCO_ON VPS clock oscillation selection bit VPS clock stop VPS clock oscillation Reserved bits Nothing is assigned. Must set to "0." x xx 17. Address 1E16 (=DA5 to 0) DD15 DD8DD7 DD0 000000 Bit symbol Reserved bits Bit name Function Must set to "0." RW Nothing is assigned. 18. Address 1F16 (=DA5 to 0) DD15 DD8DD7 DD0 00 Bit symbol Nothing is assigned. 0 1 Even field Odd field Bit name Function RW FLD1V Field state flag Reserved bits Must set to "0." 0 1 normal unusual MACRO_ON Synchronized signal search flag Nothing is assigned. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 213 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. Address 2016 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 0 000 000 Bit symbol Reserved bits Bit name Must set to "0." Function RW x xx Nothing is assigned. Vertical synchronous separation standard selection bit 0 1 Detected in L period of 15ms/22ms. Detected in L period of 22ms. SEPV0 Reserved bit Must set to "0." 0 1 0 1 Check (Data is acquired if Framing code is in agreement). No check (All data is acquired). Synchronous signal slice potential generating circuit OFF Synchronous signal slice potential generating circuit ON x NORMAL LEVELA Framing code check control bit Synchronous signal slice potential generating control bit Reserved bits Must set to "0." NXP 0 0 1 1 MPAL 0 1 0 1 Broadcast method NTSC M-PAL PAL Do not set up x NXP MPAL Broadcast method selection bit Reserved bit Must set to "0." x Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 214 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 20. Address 2116 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 01 Bit symbol Nothing is assigned. Reserved bit Reserved bit Must set to "1." Must set to "0." Bit name Function RW xx x x 21. Address 2216 (=DA5 to 0) DD15 DD8DD7 DD0 Bit symbol DIV_PDCS0 DIV_PDCS1 DIV_PDCS2 DIV_PDC0 DIV_PDC1 DIV_PDC2 DIV_PDC3 DIV_PDC4 Nothing is assigned. Bit name The PLL fine-tuning bit for PDC Function Slice clock frequency fPDC for PDC is adjusted. f PDC = fDIVP x 2 RW ( n=0 2n DIV_PDCn m-3 8 + 2 m=0 DIV_PDCSm+2 ) The divided value selection bit of PLL for PDC f DIVP : Horizontal synchronized signal frequency * When teletext (PDC) data is acquired DIV_PDC4 to 0, DIV_PDCS2 to 0 = (00100011)2 ( ( ) ) * When EPG-J is acquired DIV_PDC4 to 0, DIV_PDCS2 to 0 = (00010011)2 xx 0 1 Normal The 4-bit data of 8/4 humming is reversal-outputted. HM84SEL 8/4 humming polarity selection bit Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 215 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 22. Address 2316 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 000 0000 Bit symbol Bit name Function Slice clock frequency fPDC for VPS is adjusted. f VPS = f DIVV x 2 8 ( n=02n m-3 R DIV_VPSS0 The PLL fine-tuning bit for VPS DIV_VPSS1 DIV_VPSS2 DIV_VPS0 DIV_VPS1 DIV_VPS2 DIV_VPS3 DIV_VPS4 Reserved bits DIV_VPSn + 2 m=0 DIV_VPSSm + 2) The divided value selection bit of PLL for VPS f DIVV : Horizontal synchronized signal frequency When VPS is acquired DIV_VPS4 to 0, DIV_VPSS2 to 0 = (00100110)2 ( ) ) When CC, CC2X and ID-1 are acquired DIV_VPS4 to 0, DIV_VPSS2 to 0 = (11010100)2 ( Must set to "0." Analog input The digital input of HOR x HORAX_ON Horizontal synchronized signal 0 selection bit 1 Reserved bits Must set to "0." x Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 216 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 23. Address 2416 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol Reserved bits Bit name Function Must set to "880816" when EPG-J is acquired. Otherwise, set to "000016." RW x 24. Address 2516 (=DA5 to 0) DD15 DD8DD7 DD0 00010011000 00 Bit symbol ADSEL ADON_TIM Bit name 0 Normal A/D conversion slice bit A/D operation control bit 1 The digital value after A/D conversion is given from outside (with register). 0 1 Programmable Slice period Function RW Reserved bits Slice selection bit Must set to "0." 0 1 Every line (CHECK_START) Programmable (PRE_START) SLICEON_TIM Reserved bits Must set to "0." x x x x x Reserved bits Must set to "1." Reserved bits Must set to "0." Reserved bit Must set to "1." Reserved bits Must set to "0." Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 217 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 25. Address 2616 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol DIVP_CK0 DIVP_CK1 Bit name Function RW The clock division value The divided clock used for the phase selection bit for phase comparison with a PDC clock is set up. comparison with a PDC clock ffSC = fDIVP x (n=02n DIVS_CKn + 2) 7 DIVP_CK2 DIVP_CK3 DIVP_CK4 DIVP_CK5 DIVP_CK6 DIVP_CK7 DIVV_CK0 DIVV_CK1 ffSC = fDIVV x DIVV_CK2 DIVV_CK3 DIVV_CK4 DIVV_CK5 DIVV_CK6 DIVV_CK7 The clock division value selection bit for phase comparison with a VPS clock The divided clock used for the phase comparison with a VPS clock is set up. fDIVP: The slice clock frequency for PDC (please refer to DIV_PDCS0 to 2 and DIV_PDC0 to 4 (address 2216).) When teletext (PDC) data is acquired DIVP_CK7 to 0 = (00001110)2 When EPG-J is acquired DIVP_CK7 to 0 = (00001001)2 ( n=02n DIVV_CKn + 2) 7 fDIVV : The slice clock frequency for VPS (refer to DIV_VPSS0 to 2 and DIV_VPS0 to 4 (address 2316).) When VPS is acquired DIVV_CK7 to 0 = (00001110)2 When CC, CC2X and ID-1 are acquired DIVV_CK7 to 0 = (01010011)2 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 218 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 26. Address 2716 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 000 Bit symbol DLYSEL0 DLYSEL1 DLYSEL2 DLYSEL3 DLYSEL4 DLYSEL5 DLYSEL6 DLYSEL7 WEIGHT0 WEIGHT1 WEIGHT2 WEIGHT3 WEIGHT4 Data slicer control bit6 Bit name Data slicer control bit5 Function These are the control bits of the ghost correction circuit. RW These are the control bits of the ghost correction circuit. Reserved bits Must set to "0." x Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 219 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 27. Address 2816 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 00000 0 Bit symbol ADLAT Bit name Data acquisition selection bit 0 1 Function Acquisition of slice data Acquisition of A/D data RW START Slice data selection bit Turning on the output after slice RAM of Flaming code detection position (8 bits) and the average of the clock run-in level (8 bits)and turning off are set (note.) Reserved bit A/D lower bit selection bit 0 1 Must set to "0." Normal Stop by 6th bit of A/D Must set to "1" when EPG-J is acquired. Otherwise, set to "0." Synchronous signal slice level control bit SYNLVL2 SYNLVL1 SYNLVL0 Slice level approx.1.10V0.10V approx.1.15V0.10V approx.1.20V0.10V approx.1.25V0.10V approx.1.30V0.10V approx.1.35V0.10V approx.1.40V0.10V approx.1.45V0.10V x 6BITOFF Reserved bit x SYNLVL0 SYNLVL1 SYNLVL2 ADON INTAD INTDA 0 0 0 0 1 1 1 1 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Data slicer control bit The amplifier control bit for data slicers Data slicer OFF. (The amplifier for slicer is also turned off). Data slicer ON (see INTAD and the INTDA about the amplifier for slicer) On 3 to 23 lines and 315 to 335 line amplifier ON. On other line amplifier OFF Always ladder resistance for data slicer ON. On 3 to 23 lines and 315 to 335 line Ladder resistance ON. On other line Ladder resistance OFF 0 Always data slicer ON. The rudder resistance control 0 bit for data slicers 1 Reserved bits Must set to "0." x Note. Slice RAM: Refer to Figure "Slice RAM bit construction" SR000 to SR00F 0 : Slice data SR030 to SR03F SR010 to SR01F SR020 to SR02F Data1 Data2 Data3 SR010 to SR01F SR000 to SR00F SR020 to SR02F SR030 to SR03F 1 : Slice data Data1 Data2 Flaming code detection location (8 bits) Clock run-in average level (8 bits) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 220 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 28. Address 2916 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 0000 Bit symbol VPS_VP0 VPS_VP1 VPS_VP2 VPS_VP3 VPS_VP4 VPS_VP5 VPS_VP6 VPS_VP7 VPS_VP8 SLI_GO Slice ON/OFF control bit Synchronous separate selection bit Synchronous separate input control bit 0 1 0 1 0 1 Slice OFF Slice ON Synchronous separate circuit OFF Synchronous separate circuit ON SYNCIN analog input SYNCIN digital input Must set to "0." Bit name Setup of a slice start line (Shared by the first field and the second field) Function If a slice start line is made into SLI_VS At PAL n=0 8 n RW n=0 8 n At NTSC n=0 8 n n=0 8 n The data for 18 lines is stored in Slice RAM from the line set up by this register. SYNCSEP_ON0 STBSYNCSEP Reserved bits x Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 221 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 29. Address 2A16 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 10000000 Bit symbol MASK0 MASK1 MASK2 MASK3 MASK4 MASK5 PAL The position of mask release is set up 256 steps of setup can be performed in one fourth of the periods of the back between 1H 18H to 256H Order of 0H to 17H It cannot set up Bit name Mask width for time bases selection bit. PAL NTSC Function 1135 910 284 RW = MASK6 MASK7 Reserved bits Reserved bit 0H NTSC to 256H Usually, please make it 80H Must set to "0." Must set to "1." x x 30. Address 2B16 (=DA5 to 0) DD15 DD8DD7 DD0 0 0000 0000000 Bit symbol Reserved bits Bit name Function Must set to "0." RW x xx Nothing is assigned. Reserved bits SEL_PDCH SEL_VPSH Reserved bit SEL_PDEC The clock selection bit for a PLL lock The internal H selection bit for data slicers Must set to "0." SEL_PDCH SEL_VPSH x External Hsync From PLL for VPS From PLL for PDC VPS or PDC 0 0 1 1 0 1 0 1 Must set to "0." 0 1 VPS and a PLL lock from Hsync. VPS and a PLL lock from a X'tal system. x Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 222 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 31. Address 2C16 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 1000000 Bit symbol PLSPOS0 PLSPOS1 H Bit name Slice A/D ON period selection bit Function Slice A/D ON period is counted. V RW PLSPOS2 PLSPOS3 PLSPOS4 PLSPOS5 PLSPOS6 PLSPOS7 PLSPOS8 H of (n=02n PLSPOSn)- th shot H of 8 (n=02n PLSNEGn)- th shot 8 Reserved bits Reserved bit Must set to "0." Must set to "1." x x 32. Address 2D16 (=DA5 to 0) DD15 DD8DD7 DD0 00 0000 Bit symbol PLSNEG0 PLSNEG1 PLSNEG2 PLSNEG3 PLSNEG4 PLSNEG5 PLSNEG6 PLSNEG7 PLSNEG8 Bit name Slice-ON period selection bit Function Refer to PLSPOS0 to 8 (Address 2C16) RW Reserved bits Must set to "0." Must set to "1" when teletext (PDC) data is acquired. Must set to "0." x x x Reserved bit Reserved bits Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 223 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 33. Address 2E16 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol HCOUNT0 HCOUNT1 HCOUNT2 HCOUNT3 HCOUNT4 HCOUNT5 HCOUNT6 HCOUNT7 HCOUNT8 HCOUNT9 HCOUNT10 HCOUNT11 HCOUNT12 HCOUNT13 HCOUNT14 HCOUNT15 Bit name Synchronous detection bit Function A horizontal synchronized signal is counted. These bits are reset by set the VERTX bit (address 3316) to "0." RW 34. Address 2F16 (=DA5 to 0) DD15 DD8DD7 DD0 0 Bit symbol Nothing is assigned Bit name Function RW xx Set to "0" usually Reserved bit STB_RES Extended register all reset bit x 0 1 Normal It resets to address 0016 to the address 2E16 extended register. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 224 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 35. Address 3016 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol Nothing is assigned Bit name Function RW xx 36. Address 3116 (=DA5 to 0) DD15 DD8DD7 DD0 Bit symbol Nothing is assigned Bit name Function RW xx 37. Address 3216 (=DA5 to 0) DD15 DD8DD7 DD0 Bit symbol RMHTD0(0) RMHTD0(1) RMHTD0(2) RMHTD0(3) RMHTD0(4) RMHTD0(5) RMHTD0(6) RMHTD0(7) RMHTD0(8) Bit name Remote control header length selection bit Function In order to detect a remote control pulse in standby mode, the header length to the oscillation for clocks (address 3216) is chosen. Remote control pulse RW B A C D Effective pulse width Header part A = TXCIN x 2 RMHTD0(n) C = TXCIN x 2 RMHTD1(n) n=0 n=0 8n 8 n B = TXCIN x FILDIV0 x YUKOU0(n) D = TXCIN x FILDIV0 x YUKOU1(n) n=0 n=0 5 5 TXCIN : XCIN pin input cycle Division value set by FILDIV0 (bit 9 of address 3316) Clock division value of JUST CLOCK filter selection bit. JSTCKDIV1 JSTCKDIV0 Main clock divided value JSTCKDIV0 JSTCKDIV1 JSTCKON ON/OFF of JUST CLOCK filter selection bit. 0 1 0 0 1 1 0 1 0 1 32 divided 64 divided 128 divided 256 divided Filter OFF Filter ON Nothing is assigned. RMTSEL Remote control header polarity selection bit 0 1 No reverse reverse xx Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 225 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 38. Address 3316 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 0 0 Bit symbol RMHTD1(0) RMHTD1(1) RMHTD1(2) RMHTD1(3) RMHTD1(4) RMHTD1(5) RMHTD1(6) RMHTD1(7) RMHTD1(8) FILDIV0 Clock division value of remote Clock division value for Remote control tolerance period measurement is selected. (Note 1) control pulse selection bit FILDIV0 0 1 Sub clock divided value No divided 2 Bit name Remote control header length selection bit Function Refer to RMHTD0 (0) to (8) (address 3216). RW Reserved bit Must set to "0. " OFF ON Reset Horizontal synchronized signal count FILON VERTX Filter ON/OFF of remote control 0 pulse selection bit (Notes 2, 3) 1 Synchronous detection reset bit 0 1 Reserved bit Filter of remote control clock divide value selection bit Must set to "0. " FILDIV1(1) 0 0 1 1 FILDIV1(0) Sub clock divided value 2 0 4 1 8 0 16 1 FILDIV1(0) FILDIV1(1) Notes 1. Refer to RMHTD0 (0) to (8) (address 3216) Notes 2. Change these bits at initialization and do not rewrite during remote control receive. Notes 3. The remote control pulse filter is only for the sub clock. Set it to OFF when the sub clock is not mounted. 39. Address 3416 (=DA5 to 0) DD15 DD8DD7 DD0 01110000 Bit symbol Reserved bits Bit name Function Must set to "7016." Must set to "DD16" when EPG-J is acquired. Otherwise, set to "0016." RW x x Reserved bits Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 226 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 40. Address 3516 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 0000011 Bit symbol HINT_LINE0 Bit name H_INT interruption position selection bit Function A period after V is inputted until H_INT rises is counted. V H RW HINT_LINE1 HINT_LINE2 HINT_LINE3 H_INT HINT_LINE4 n=0 2 HINT_LINEn 8n HINT_LINE5 HINT_LINE6 HINT_LINE7 HINT_LINE8 Reserved bits Reserved bits Reserved bit Must set to "1." Must set to "0." Must set to "0." x Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 227 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 41. Address 3616 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol VINT0 VINT1 VINT2 VINT3 INTRMT0 INTRMT1 INTRMT2 INTRMT3 HINT0 HINT1 HINT2 HINT3 SECINT0 SECINT1 SECINT2 SECINT3 Bit name SLICEON interruption control test bit Function 0000 : Interrupt disabled (Note 3) 1011 : Interrupt enabled Others : Do not set up When the period of data acquisition expires, the interrupt occurs by setting these bits to 1011. Set up the TB5IC register (Note 4) when use by "Interrupt enabled." RW Remote control interruption control bit (Note 1) 0000 : Interrupt disabled (Note 3) 1010 : Interrupt enabled Others : Do not set up Set up the TB4IC register (Note 4) when use by "Interrupt enabled." HINT interruption control test bit (Note 2) 0000 : Interrupt disabled (Note 3) 1001 : Interrupt enabled Others : Do not set up Set up the TB3IC register (Note 4) when use by "Interrupt enabled." Clock timer interruption control bit 0000 : Interrupt disabled (Note 3) 1000 : Interrupt enabled (Note 5) Others : Do not set up Set up the TB2IC register (Note 4) when use by "Interrupt enabled." Notes 1. Refer to 15.6 Expansion Register Construction Composition. Notes 2. Refer to the function of HINT_LINEn (Address 3516.) Notes 3. Set these bits to 0000 when use the interrupt of Timer B2, Timer B3, Timer B4, or Timer B5. Notes 4. Refer to Figure 6.3 Interrupt Control Registers. Notes 5. When the second counter (Address 3916) is changed, an interrupt is generated every 1 second. Notes 6. Please do not change data after setting initial data to address 3616 corresponding interrupt control bit VINTi, INTRMTi, HINTi, and SECINTi (i = 0 to 3) when you use the SLICEON, remote control, HINT, and the clock timer interrupt. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 228 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 42. Address 3716 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol YUKOU0(0) YUKOU0(1) YUKOU0(2) YUKOU0(3) YUKOU0(4) YUKOU0(5) Nothing is assigned. YUKOU1(0) YUKOU1(1) YUKOU1(2) YUKOU1(3) YUKOU1(4) YUKOU1(5) Nothing is assigned. Bit name Remote control header judging pulse length selection bit 0 Function Refer to RMTHD0(0) to (8) (Address 3216) RW xx Refer to RMTHD0(0) to (8) (Address 3216) Remote control header judging pulse length selection bit 1 xx 43. Address 3816 (=DA5 to 0)\ DD15 DD8DD7 DD0 0000000000000000 Bit symbol Reserved bit Bit name Function Must set to "0." RW Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 229 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 44. Address 3916 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol SECOUT0 SECOUT1 SECOUT2 SECOUT3 SECOUT4 SECOUT5 Nothing is assigned. RTCON Bit name Clock Timer Second Setting Bit Function Set seconds (0 to 59 seconds) of clock timer. The settable values are 0 to 59. RW xx 0 1 Clock timer stops Clock timer operates Clock Timer Operation Selection Bit Nothing is assigned. SECJUST Second Just Setting Bit When writing "1", less than second of the clock timer is reset. When reading, the value is "0". xx x 45. Address 3A16 (=DA5 to 0) DD15 DD8DD7 DD0 Bit symbol MINOUT0 MINOUT1 MINOUT2 MINOUT3 MINOUT4 MINOUT5 MINOUT6 MINOUT7 MINOUT8 MINOUT9 MINOUT10 Nothing is assigned. Bit name Clock Timer Minute Setting Bit Function Set hours and minutes of the clock timer by the minute. The settable values are 0 to 1439 (00:00 to 23:59) RW xx Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 230 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 46. Address 3B16 (=DA5 to 0) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol DAYCUONT0 DAYCUONT1 DAYCUONT2 DAYCUONT3 DAYCUONT4 DAYCUONT5 DAYCUONT6 DAYCUONT7 DAYCUONT8 DAYCUONT9 DAYCUONT10 DAYCUONT11 DAYCUONT12 DAYCUONT13 DAYCUONT14 DAYCUONT15 Bit name Clock Timer Day Setting Bit Function Set days of the clock timer. The settable value are 0 to 65535. RW Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 231 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 47. Address 3C16 (=DA5 to 0) (Note 1) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol RMTSTART Bit name Function RW Remote control transmission Start and the stop of wave form output is selected. start bit 0: Stop 1: Start Carrier selection bit The output mode of remote control transmission wave form is selected. 000: External wave, Carrier and AND output. 010: External wave, Carrier and OR output. 101: Only external wave is output (carrier none.) Additionally: Setting prohibition. Carrier's clock source is selected. 00: The main clock (There is not dividing frequency.) 01: 2.5 dividing of the main clock. 10: 8 dividing of the main clock. 11: Setting prohibition. The clock source of external wave is selected. 00: The main clock (There is not dividing frequency.) 01: 8 dividing of the main clock. 10: 64 dividing of the main clock. 11: 256 dividing of the main clock. IRPOL(0) IRPOL(1) IRPOL(2) RMCDIV(0) RMCDIV(1) Carrier clock source selection bit RMTDIV(0) RMTDIV(1) RMT_TM(0) RMT_TM(1) RMT_TM(2) RMT_TM(3) RMT_TM(4) RMT_TM(5) RMT_TM(6) RMT_TM(7) External wave clock source selection bit External wave clock dividing Dividing frequency value which is selected by RMTDIV(1, 0) frequency value setting bit Set RMT_TM. RMT_TM = 2n * RMT_TM0(n) n=0 7 Note 1. Refer to 14.6 "(6) Remote control transmission function." Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 232 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 48. Address 3D16 (=DA5 to 0) (Note 1) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION Bit symbol RMT_TML(0) RMT_TML(1) RMT_TML(2) RMT_TML(3) RMT_TML(4) RMT_TML(5) RMT_TML(6) RMT_TML(7) RMT_TMH(0) RMT_TMH(1) RMT_TMH(2) RMT_TMH(3) RMT_TMH(4) RMT_TMH(5) RMT_TMH(6) RMT_TMH(7) Bit name Function RW Carrier L period setting bit Carrier's L period is set. RMT_TML = 2n * RMT_TML(n) n=0 7 Carrier H period setting bit Carrier's H period is set. RMT_TMH = 2n * RMT_TMH(n) n=0 7 Note 1. Refer to 14.6 "(6) Remote control transmission function." 49. Address 3E16 (=DA5 to 0) (Note 1) DD15 DD8DD7 DD0 0 0 Bit symbol RMTTXINT(0) RMTTXINT(1) RMTTXINT(2) RMTTXINT(3) Reserved bit Nothing is assigned. Must set to "0." Bit name Function RW Remote control transmission 0000: Interrupt prohibition (Note 2) interrupt control 0001: Interrupt permission (Note 1, Note 4) Additionally: Setting prohibition Please set INT2IC register when using it by "Interrupt permission." IROUT_SLICEON P84 output signal selection bit 2 (Note 3) 0: Normal setting (When use P84 I/O port or INT2 interrupt.) 1: Remote control transmission pulse output Must set to "0." Reserved bit Notes 1. Refer to 14.6 "(6) Remote control transmission function." Notes 2. Set and use 00002 when use INT2 interrupt. Notes 3. Set "1" to bit b4 of port P8 direction register when use the remote control transmission function. Notes 4. Please do not change data after setting the initialization data to remote control transmission interrupt control bit RMTTXINT(i) (i = 0 to 3) when you use the remote control transmission interrupt. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 233 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 50. Address 3F16 (=DA5 to 0) (Note 1) DD15 DD8DD7 DD0 14. EXPANSION FUNCTION 0 Bit symbol Nothing is assigned. Bit name Function RW Reserved bit Must set to "0." Note 1. Refer to 14.6 "(6) Remote control transmission function." 51. Address 4016 (=DA5 to 0) CD15 CD8CD7 CD0 Bit symbol FPLS_MIN0 Bit mane Fixed length pulse lower bound value setting bit Function The fixed length pulse lower bound value is set. (note 1) RW FPLS_MIN1 FPLS_MIN2 FPLS_MIN3 FPLS_MIN4 FPLS_MIN5 FPLS_MIN6 FPLS_MIN7 FPLS_MAX0 Fixed length pulse upper bound value setting bit The fixed length pulse upper bound value is set. (note 1) FPLS_MAX1 FPLS_MAX2 FPLS_MAX3 FPLS_MAX4 FPLS_MAX5 FPLS_MAX6 FPLS_MAX7 *Note 1: The fixed value pulse is a pulse ("H" or "L" part) where 0/1 is not judged. It does according to enhancing register VBITPOL (Address 4316 and bit 13) at H period of 0/1 judgments or it does at L period or it selects it. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 234 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 52. Address 4116 (=DA5 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol DT0_MIN0 Bit name "0" data pulse length lower bound value setting bit Function "0" data pulse length lower bound value is set. RW DT0_MIN1 DT0_MIN2 DT0_MIN3 DT0_MIN4 DT0_MIN5 DT0_MIN6 DT0_MIN7 DT0_MAX0 "0" data pulse elder limit value "0" data pulse elder limit value is set setting bit DT0_MAX1 DT0_MAX2 DT0_MAX3 DT0_MAX4 DT0_MAX5 DT0_MAX6 DT0_MAX7 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 235 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 53. Address 4216 (=DA5 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol DT1_MIN0 Bit name Function "1" data pulse length lower bound value is set. RW "1" data pulse length lower bound value setting bit DT1_MIN1 DT1_MIN2 DT1_MIN3 DT1_MIN4 DT1_MIN5 DT1_MIN6 DT1_MIN7 DT1_MAX0 "1" data pulse elder limit value "1" data pulse elder limit value is set. setting bit DT1_MAX1 DT1_MAX2 DT1_MAX3 DT1_MAX4 DT1_MAX5 DT1_MAX6 DT1_MAX7 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 236 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 54. Address 4316 (=DA5 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol MAXBIT0 Bit name The maximum reception bit number setting bit Function The number of maximum reception bits is set. RW MAXBIT1 MAXBIT2 MAXBIT3 MAXBIT4 MAXBIT5 MINBIT0 Minimum reception bit number setting bit The number of minimum reception bits is set. MINBIT1 MINBIT2 MINBIT3 MINBIT4 MINBIT5 RMTLSB LSB/MSB reception selection bit 0/1 judgment level selection bit Interrupt selection bit 0:It receives it with MSB. 1:It receives it with LSB. 0:0/1 is judged at L period. 1:0/1 is judged at H period. 0:After it matches it, interrupt is generated. 1:When a reception of the data of the 16th bit and the maximum data are received, interrupt is generated VBITPOL INTSEL GET_DATA Bit that takes data 1:When "1" is written from the reception buffer in the reception register, the data of the reception buffer is written in the reception register. (The value when reading it is 0. ) x Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 237 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 55. Address 4416 (=DA5 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol DATAOL0 Bit name Number of receive data bits Function The number of bits of received data is displayed. RW DATAOL1 DATAOL2 x DATAOL3 DATAOL4 DATAOL5 NU0 Number of receive data words 16 piece nbit data was received. (n=0,1,2) x NU1 INTRMTFL0 One word reception completion flag The reception completion of 0/1 data for one word (16 bits) is shown. 0:The data of the 16th bit is not received. 1:The data of the 16th bit was received 0:The data of the number of maximum bits was not received. 1:The data of the number of maximum bits was received 0:Everything did not receive the data. 1:Everything received the data. 1:There was NG while receiving it. x INTRMTFL1 Flag that received data of number of maximum bits x INTRMTFL2 NG Flag that received the data everything NG flag bit of reception x x xx Nothing is assigned. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 238 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 56. Address 4516 (=DA5 to 0) CD15 CD8CD7 CD0 14. EXPANSION FUNCTION Bit symbol RMTDA0 Bit name Reception register Function The received data ("H" data 0/1 judgments by the period of "L") is stored. RW x x x x x x x x x x x x x x x x RMTDA1 RMTDA2 RMTDA3 RMTDA4 RMTDA5 RMTDA6 RMTDA7 RMTDA8 RMTDA9 RMTDA10 RMTDA11 RMTDA12 RMTDA13 RMTDA14 RMTDA15 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 239 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION 14.6 Expansion Register Construction Composition (1) Acquisition timing The SLICEON signal is output in the acquisition possible period. The first field Vertical blanking erase period pulse Acquisition possible period 626 2 5 2 23 6 4 62 1 2 3 4 5 6 7 8 9 1 9 20 21 22 23 24 SLICEON output period The second field 310 311 312 313 314 315 316 317 318 319 320 321 331 332 333 334 335 336 The scanning lines number in figure is corresponds to slice RAM. This is the line to support when the PAL video signal is sliced and setting the expansion registers to VPS_VP8 to VPS_VP0 (bits 8 to 0 in address 2916) = "416". Figure 14.11 Expansion register access registers composition (2) Synchronized signal detection circuit The number of pulses of the horizontal synchronized signal of a compound video signal is counted during a fixed period. The horizontal synchronous number of pulses can always be read from an expansion register. A block diagram is shown in Figure. 14.12. Address bus Data bus The arbitration circuit for expansion registers Latch Q HOR T 16bit counter Possible to count C00016 at maximum. Figure 14.12 Block diagram of Synchronized detection circuit Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 240 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION (3) Register related to Slicer The relation between V, H signal, and the register related to slicer is shown in Figure. 14.13 and Figure. 14.14. V after SYNC separation VPS_VP 0 to 8 (address 2916) Setting the slice start line After V input The first line The second line *** The nth line The (n+1)th line The (n+17)th line H after SYNC separation After slice start The 0th line The 1th line On the odd field LN0_OD1 LN0_OD0 On the even field LN0_EV1 LN0_EV0 On the odd field LN1_OD1 LN1_OD0 On the even field LN1_EV1 LN1_EV0 The 17th line On the odd field LN17_OD1 LN17_OD0 On the even field LN17_EV1 LN17_EV0 *** Selection of a state register (addresses 00 to 0516) (18 lines) Figure 14.13 Register related to slicer (1) Clock GETPEEK2 SELVCO, DIVS0 to 1 (Addresses 0A, 11, 1816) (Addresses 06, 0D, 1416) Selection of the clock Selection of the clock for slice GET_HP0 to 1 compensation after HOGO2(Addresses 09, 10, 1716) (Addresses 0A, 11, 1816) a peak detection Selection of the clock for Phase adjustment period end data acquisition Clock run-in Framing code Data H after sync separation SLSLVL0 to 1(Addresses 09, 10, 1716) Slice level measurement period selection 6 cycles GETPEEK3 (Addresses 0A, 11, 1816) A mountain and valley detection selection Fixed FLC0 to 15 (Addresses 07, 0C, 1316) Framing code selection CHK_FLC0 to 15 (Addresses 08, 0D, 1416) Framing code check selection BIFON(Addresses 07, 0C, 1316) Data formal selection Fixed SLS_HP0 to 7(Addresses 0A, 11, 1816) Setting slice check start position Figure 14.14 Register related to slicer (2) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 241 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION (4) Remote control pattern recognition Pattern matching of remote control is performed using a sub clock oscillation. Remote control input is input from RMTIN terminal. Interruption is generated when pattern matching is in agreement. 4 times match noise filter is being included, in front of the pattern matching circuit. A block diagram is shown in Figure 14.15. The example of a waveform of pattern matching is shown in Figure.14.16. The flow of pattern matching is shown in Figure.14.17. Sub clock fc FILDIV1(1, 0) bit P94/TB4in /RMTin divider FILDIV0 bit Polarity selection divider for B/D period Four time agreement Filter Header pattern match circuit Interruption Control Timer B4/remote control interrupt request FILON bit Port 94 Input buffer RMTSEL bit A period:RMTHD0 B period:YUKOU0 C period:RMTHD1 D period:YUKOU1 Timer B4 INTRMT3 to 0 bit Timer B4 interrupt Figure 14.15 Remote control pattern recognition block diagram RMTIN B D A C Header 0 data 1 data The number of registers A B C D "L" check programmable Check of a rising edge "H" check programmable Check of a falling edge 9 bit 6 bit 9 bit 6 bit At maximum check time 15.6 ms 3.8 ms (Note 2) 15.6 ms 3.8 ms (Note 2) Note 1. 1bit unit 32.768kHz (a part for one clock) Note 2. The maximum check period of B and D is the values when enhancing register FILDIV0 (Address 3316) is set to "1". Figure 14.16 Example of waveform of pattern matching Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 242 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION Initial pulse waiting state Detect a falling edge? Yes No Retain the "L" state during A? Yes Detect a rising edge during B? No No Yes Retain the "H" state during C? No Yes Detect a falling edge during D? No Yes Interruption generating Figure 14.17 Flow of pattern matching 4 times match process operation This is a 4 times match digital filter using the sub clock oscillation. The input signal of the RMTin pin is sampled 4 times and the output level will change only when the level matches 4 times. When using this filter, set the FILON bit (bit11) in the expansion register 33H to "1". The signal after passing 4 times match filter is applied to the header pattern matching circuit and timer B4 at filter ON. The sampling rate can be changed by the FILDIV1 (1, 0) bit in the expansion register 33H. Refer to the FILDIV1 bit of the expansion register 33H function description for details. The input signal is through supplied to the latter circuit at filter OFF. (no clock delay).Since this filter operates only with the sub clock and cannot be used for the main clock, set the filter to OFF (FILON bit ="0") when the sub clock is not mounted. (5) Clock timer function The sub clock is selected as the count source and the clock timer can set and read the count value every day, minute and second. It has the following functions. Clock function 1.This timer is dedicated clock function which is independent from timer A and timer B. 2.The settable ranges of day, minute and second are 0 to 65535 days, 0 to 1439 minutes and 0 to 59 seconds. 3.Second just setting is available (reset the count value of less than second). 1 second interrupt 1.The interrupt request is generated when second of the clock timer is incremented. (The interrupt request is not generated at the second just setting.) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 243 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION (6) Remote control transmission function The career is synthesized to two kinds of pulses of external wave, and the remote control transmission circuit is output from the microcomputer pin. The specification of the remote control transmitter is shown in Table 14.5, The remote control transmission circuit output wave form is shown in Figure 14.18, and The remote control transmission circuit block chart is shown in Figure 14.19. The feature is shown below. * Career is a continuous pulse of the arbitrary width obtained by dividing the main clock (Figure 14.18 Wave forms 2 and 3.) * External wave is a shape of waves generated from the transmission data buffer with reading pin output value ("H"/"L") and the pulse width one by one (Figure 14.18 Wave form 4.) * The shape of waves that can synthesize the career to external wave is output from the pin (Figure 14.18 Wave form 5.) Table 14.5 Item Specification of remote control transmission function Specifications Carrier: Selection from f1 (There is not XIN dividing frequency), f2.5 (XIN 2.5 dividing frequency), and f8 (XIN 8 dividing frequency.) External wave: Selection from f1 (There is not XIN dividing frequency), f8 (XIN 8 dividing frequency), f64 (XIN 64 dividing frequency), and f256 (XIN 256 dividing frequency.) Down count The register for "H" width setting is read by standing up about the pulse, and it continues the count. The register for "L" width setting is read by standing up about the pulse, and it continues the count. "H" period and "L " period are 1 to 256. Down count Wave form output value ("H"/"L") and the count value are read from the remote control transmission data buffer with stand up/fall down of the pulse, and the port output and the count are continued. 1 to 16384 (14bit) Count source Count operation (carrier) Comparing of dividing frequency (carrier) Count operation (external wave) Comparing of dividing frequency (external wave) Start of counting condition Count stop condition The remote control transmission start bit is set to "1." The remote control transmission start bit is set to "0." After the untransmission data number reference bit is empty and the count value is underflow When external wave stand up/fall down (When the value of the interrupt setting bit read from the remote control transmission data buffer is only 1. ) OR output of career and external wave Only external wave is output (carrier none.) Interrupt generation timing Remote control transmission mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 244 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION 1) Count source (f1/f2.5/f8) H period 2) Transportation wave form (axis expansion of time) 3) Transportation wave form (axis reduction of time) L period 4) External wave form T0 period 5) P8-4 pins wave form 6) Interrupt request signal Figure 14.18 Remote control transmission circuit output wave form Clock f1 f2.5 f8 H period L period Career Remote control transmission pulse External wave External wave generation part underflow External wave generation circuit Interrupt request Career timer Career generation part f1 f8 f64 f256 Clock Data bus ..... Writing-in counter Number of untransmission data Reading-out counter . . . Register WR Figure 14.19 Remote control transmission circuit block chart Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 245 of 326 Reading-out selector Writing-in selector Remote control transmission data buffer (FIFO 7 words) b15 b13 b0 External wave pulse period set bit Interrupt setting bit External wave output data setting bit M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION Remote control transmission data buffer register DD15 DD8DD7 DD0 Symbol RMT_TMHL Bit symbol RMT_TMHL (0) RMT_TMHL (1) RMT_TMHL (2) RMT_TMHL (3) RMT_TMHL (4) RMT_TMHL (5) RMT_TMHL (6) RMT_TMHL (7) RMT_TMHL (8) RMT_TMHL (9) RMT_TMHL (10) RMT_TMHL (11) RMT_TMHL (12) RMT_TMHL (13) Address 20016 Bit name External wave pulse period setting/Untransmission data number reference bit When reset 000016 Function When writing in: Set one pulse period of the remote control transmission external wave. When reading out: The number of data (number of untransmission data) that remains in the remote control transmission data buffer is read out. RW Interrupt setting bit RMT_TMHL (14) The presence of the interrupt generation is specified at the change of the external wave output. 0:The interrupt request signal is not generated. 1:The interrupt request signal is generated. The remote control transmission external wave data is set. RMT_TMHL (15) External wave output data setting bit Figure 14.20 Setting of enhancing register (Only the part related to the remote control transmission.) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 246 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION 14.7 8/4 Humming Decoder 8/4 humming decoder operates only by written the data which is 8/4 humming- encoded to 8/4 humming register (address 021A16). 8/4 humming register consists of 16 bits, can decode two data at once. Can obtain the decoded result by reading 8/4 humming register, and the decoded value and error information are output. Corrects and outputs the decoded value for single error, and outputs only error information for double error. Decoded result is shown in Figure 14.21 and humming 8/4 register composition is shown in Figure 14.22. Humming data (2) MSB LSB MSB Humming data (1) LSB Writing Address 021A16 8/4 humming register Reading Error information (2) 0 0 Error information (1) 0 0 Decode value (2) MSB LSB Decode value (1) MSB LSB "1" output when single error "1" output when double error "1" output when single error "1" output when double error Figure 14.21 Decoded result Humming 8/4 register b15 b8 b7 b0 Symbol HM8 Address 021A16 When reset 000016 Function 8/4 humming decoder operates only by written the data which 8/4 humming-decoded to 8/4 humming register. Can obtain the decoded result by reading this register, and can decode 2 couples of data at the same time. RW Figure 14.22 Humming 8/4 register composition Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 247 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION 14.8 24/18 Humming Decoder 24/18 humming decoder operates only by written the data which is 24/18 humming-encoded to 24/18 humming register 0 (address 021C16) and 1 (address 021E16). Can obtain the decoded result by reading the same 24/18 humming register, and the decoded value and error information are output. Decoded result is shown in Figure 14.23 and humming 24/18 register composition is shown in Figure 14.24. Humming data H MSB Humming data M Humming data L LSB Writing Address 24/18 humming register 1 Writing 24/18 humming register 0 Reading Decode value MSB 021E16 Address 021C16 Reading Error information Decode value LSB 0 0 0 0 0 0 0 0 0 "1" output when single error "1" output when double error The mistake by one pile is corrected and output. Figure 14.23 Decoded result Humming 24/18 register 0 b15 8 7 0 Symbol HM0 Address 021C16 When reset 000016 Function 24/18 humming decoder operates by two ways : writing data low-order and middle-order 16 bits to this register and writing data high-order 8 bits to humming 24/18 register 1 (021E16). Can obtain the decoded result by reading this register and humming 24/18 register 1. RW Humming 24/18 register 1 b15 8 7 0 Symbol HM1 Address 021E16 When reset 000016 Function 24/18 humming decoder operates by two ways : writing data low-order and middle-order 16 bits to humming 24/18 register 0 (021C16) to this register and writing data high-order 8 bits to this register. Can obtain the decoded result by reading this register and humming 24/18 register 0. RW Figure 14.24 Humming 24/18 register composition Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 248 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION Continuous error correction When uses humming 8/4 (address 021A16) at the same time as humming 24/18, can do the continuous error correction. Continuous error correction sequence is shown in Figure 14.25. A Humming data (1) M Humming data (2) L Humming data (2) H Humming data (3) M Humming data (4) L Humming data (4) H Humming data (1) L Humming data (1) H Humming data (2) M Humming data (3) L Humming data (3) H Humming data (4) M B C D E F 1. Writes data A to address 021C16 and writes data B to address 021E16. (Setting the humming data (1) and L of humming data (2).) 2. Reads addresses 021C16 and 021E16 data (Obtains the decoded value and error information on the humming data (1)). 3. Writes data C to address 021A16 (Setting H and M of the humming data (2)). 4. Reads addresses 021C16 and 021E16 data (Obtains the decoded value and error information on the humming data (2)). 5. Writes data D to address 021C16 and writes data E to 021E16 (Setting the humming data (3) and L of humming data (4).) 6. Reads addresses 021C16 and 021E16 data (Obtains the decoded value and error information on the humming data (3)). 7. Writes data F to address 021A16 (Setting H and M of the humming data (4)). 8. Reads addresses 021C16 and 021E16 data (Obtains the decoded value and error information on the humming data (4)). Figure 14.25 Continuous error correction sequence Then, because using a part of circuit of humming 8/4 about this operation, cannot use this operation at the same time. When using the humming circuit, do the decoded result reading operation at once after the setting data of humming. And do not access other memories (Including the humming circuit) before reading of the decoded result. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 249 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION 14.9 I/O Composition of pins for Expansion Function Figure 14.26 and figure 14.27 show pins for expansion function. CVIN1 input VCC2 for slicer (Note 2) VSS SYNCIN from internal circuit to internal circuit VDD2 VCC2 from internal circuit input (Note 2) VSS to internal circuit VSS2 VDD2 LP3, LP4 V DD2 from internal circuit (Note 2) VSS VSS2 output to internal circuit Notes 1. Refer to expansion register composition (Address 3516.) Notes 2. This is a parasitic diode. The applied voltage to each port should hot exceed VCC. (VCC: VCC2 for CVIN1 and SYNCIN, and VDD2 for LP3 and LP4.) Figure 14.26 Pins for expansion function (1) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 250 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 14. EXPANSION FUNCTION VCCOFF VCC2 input (Note 1) VSS VSS2 to internal circuit STARTB VCC2 input to internal circuit VSS Note 1. This is a parasitic diode. The applied voltage to each port should hot exceed VCC. (VCC=VCC2) Figure 14.27 Pins for expansion function (2) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 251 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 15. PROGRAMMABLE I/O PORTS 15. Programmable I/O Ports The programmable input/output ports (hereafter referred to simply as "I/O ports") consist of 79 lines P0 toP9 (except P85). Each port can be set for input or output every line by using a direction register, and can also be chosen to be or not be pulled high every 4 lines. P85 is an input-only port and does not have a pull-up resistor. Port P85 shares the pin with NMI, so that the NMI input level can be read from the P8 register P8_5 bit. Figures 15.1 to 15.5 show the I/O ports. Figure 15.6 shows the I/O pins. Each pin functions as an I/O port, a peripheral function input/output. For details on how to set peripheral functions, refer to each functional description in this manual. If any pin is used as a peripheral function input, set the direction bit for that pin to "0" (input mode). Any pin used as an output pin for peripheral functions is directed for output no matter how the corresponding direction bit is set. 15.1 Port Pi Direction Register (PDi Register, i = 0 to 9) Figure 15.7 shows the direction registers. This register selects whether the I/O port is to be used for input or output. The bits in this register correspond one for one to each port. No direction register bit for P85 is available. 15.2 Port Pi Register (Pi Register, i = 0 to 9) Figure 15.8 show the Pi registers. Data input/output to and from external devices are accomplished by reading and writing to the Pi register. The Pi register consists of a port latch to hold the output data and a circuit to read the pin status. For ports set for input mode, the input level of the pin can be read by reading the corresponding Pi register, and data can be written to the port latch by writing to the Pi register. For ports set for output mode, the port latch can be read by reading the corresponding Pi register, and data can be written to the port latch by writing to the Pi register. The data written to the port latch is output from the pin. The bits in the Pi register correspond one for one to each port. 15.3 Pull-up Control Register 0 to Pull-up Control Register 2 (PUR0 to PUR2 Registers) Figure 15.9 shows the PUR0 to PUR2 registers. The PUR0 to PUR2 register bits can be used to select whether or not to pull the corresponding port high in 4 bit units. The port chosen to be pulled high has a pull-up resistor connected to it when the direction bit is set for input mode. 15.4 Port Control Register Figure 15.10 shows the port control register. When the P1 register is read after setting the PCR register's PCR0 bit to "1", the corresponding port latch can be read no matter how the PD1 register is set. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 252 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 15. PROGRAMMABLE I/O PORTS P00 to P07 P20 to P27, P30 to P37, P40 to P47, P50 to P54, P56 (There are inside of broken lines) (There is nothing inside of broken lines) Data bus Pull-up selection Direction register Port latch (Note 1) Analog input Pull-up selection P10 to P14 Direction register Port P1 control register Data bus Port latch (Note 1) Pull-up selection P15 to P17 Direction register Port P1 control register Data bus Port latch (Note 1) Input to respective peripheral functions Pull-up selection P57, P60, P64, P73, P76, P80, P81, P84, P90, P92 Data bus Direction register "1" Output Port latch (Note 1) Input to respective peripheral functions Note 1: symbolizes a parasitic diode. Make sure the input voltage on each port will not exceed VCC. (VCC: VCC1 for the port P6 to P7 and P80 to P84, and VCC2 for the port P0 to P5, P85 to P87 and P9.) Figure 15.1 I/O Ports (1) Page 253 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 15. PROGRAMMABLE I/O PORTS Pull-up selection Direction register "1" P61, P65, P72 Output Data bus Port latch Switching between CMOS and Nch Input to respective peripheral functions (Note 1) Pull-up selection P82 to P83 Direction register Data bus Port latch (Note 1) Input to respective peripheral functions Pull-up selection Direction register P55, P77, P91, P97 Data bus Port latch (Note 1) Input to respective peripheral functions Note 1: symbolizes a parasitic diode. Make sure the input voltage on each port will not exceed VCC. (VCC: VCC1 for the port P6 to P7 and P80 to P84, and VCC2 for the port P0 to P5, P85 to P87 and P9.) Figure 15.2 I/O Ports (2) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 254 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 15. PROGRAMMABLE I/O PORTS Pull-up selection Direction register P62, P66 Data bus Port latch (Note 1) Switching between CMOS and Nch Input to respective peripheral functions Pull-up selection P63, P67, P74, P75 Direction register "1" Data bus Port latch Output (Note 1) Switching between CMOS and Nch P85 Data bus NMI interrupt input (Note 1) P70, P71 Direction register "1" Output Data bus Port latch (Note 2) Input to respective peripheral functions Note 1: symbolizes a parasitic diode. Make sure the input voltage on each port will not exceed VCC. (VCC: VCC1 for the port P6 to P7 and P80 to P84, and VCC2 for the port P0 to P5, P85 to P87 and P9.) Note 2: symbolizes a parasitic diode. Figure 15.3 I/O Ports (3) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 255 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 15. PROGRAMMABLE I/O PORTS Pull-up selection Direction register P93, P94 Data bus Port latch (Note) Input to respective peripheral functions Pull-up selection P96 Direction register "1" Data bus Port latch Output (Note) Analog input Pull-up selection Direction register P95 "1" Data bus Output Port latch (Note) Input to respective peripheral functions Analog input Note: symbolizes a parasitic diode. Make sure the input voltage on each port will not exceed VCC. (VCC=VCC2) Figure 15.4 I/O Ports (4) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 256 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 15. PROGRAMMABLE I/O PORTS Pull-up selection Direction register P87 Data bus Port latch (Note) fc Rf Pull-up selection P86 Direction register "1" Data bus Port latch Output (Note) Rd Note: symbolizes a parasitic diode. Make sure the input voltage on each port will not exceed VCC. (VCC=VCC2) Figure 15.5 I/O Ports (5) CNVSS CNVSS signal input (Note 2) (Note 1) RESET RESET signal input (Note 1) symbolizes a parasitic diode. Make sure the input voltage on each port will not exceed Vcc. Note 2: A parasitic diode on the VCC side is added to the mask ROM version. Make sure the input voltage on each port will not exceed Vcc. (Vcc=Vcc2) Note 1: Figure 15.6 I/O Pins Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 257 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 15. PROGRAMMABLE I/O PORTS Port Pi direction register (i=0 to 7 and 9) (Note 1, 2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol PD0 to PD3 PD4 to PD7 PD9 Bit symbol PDi_0 PDi_1 PDi_2 PDi_3 PDi_4 PDi_5 PDi_6 PDi_7 Address 03E216, 03E316, 03E616, 03E716 03EA16, 03EB16, 03EE16, 03EF16 03F316 Bit name Function After reset 0016 0016 0016 RW RW RW RW RW RW RW RW RW Port Pi0 direction bit Port Pi1 direction bit Port Pi2 direction bit Port Pi3 direction bit Port Pi4 direction bit Port Pi5 direction bit Port Pi6 direction bit Port Pi7 direction bit 0 : Input mode (Functions as an input port) 1 : Output mode (Functions as an output port) (i = 0 to 7 and 9) Note 1: Make sure the PD9 register is written to by the next instruction after setting the PRCR register's PRC2 bit to "1" (write enabled). Port P8 direction register b7 b6 b5 b4 b3 b2 b1 b0 Symbol PD8 Address 03F216 Bit name Port P80 direction bit Port P81 direction bit Port P82 direction bit Port P83 direction bit After reset 00X000002 Function RW RW RW RW RW RW Bit symbol PD8_0 PD8_1 PD8_2 PD8_3 PD8_4 (b5) PD8_6 PD8_7 0 : Input mode (Functions as an input port) 1 : Output mode (Functions as an output port) Port P84 direction bit Nothing is assigned. In an attempt to write to this bit, write "0". The value, if read, turns out to be indeterminate. Port P86 direction bit Port P87 direction bit 0 : Input mode (Functions as an input port) 1 : Output mode (Functions as an output port) RW RW Reserved register b7 b6 b5 b4 b3 b2 b1 b0 11 11 11 11 Symbol RSV03F6 Address 03F616 After reset 0016 Bit symbol (b7-b0) Bit name Reserved bits Function Must set to "1." RW RW Figure 15.7 PD0 to PD9 Registers Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 258 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 15. PROGRAMMABLE I/O PORTS Port Pi register (i=0 to 7 and 9) (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol P0 to P3 P4 to P7 P9 Bit symbol Pi_0 Pi_1 Pi_2 Pi_3 Pi_4 Pi_5 Pi_6 Pi_7 Address 03E016, 03E116, 03E416, 03E516 03E816, 03E916, 03EC16, 03ED16 03F116 Bit name Port Pi0 bit Port Pi1 bit Port Pi2 bit Port Pi3 bit Port Pi4 bit Port Pi5 bit Port Pi6 bit Port Pi7 bit After reset Indeterminate Indeterminate Indeterminate Function RW RW RW RW RW RW RW RW RW The pin level on any I/O port which is set for input mode can be read by reading the corresponding bit in this register. The pin level on any I/O port which is set for output mode can be controlled by writing to the corresponding bit in this register 0 : "L" level 1 : "H" level (Note 1) (i = 0 to 7 and 9) Note 1: Since P70 and P71 are N-channel open drain ports, the data is high-impedance. Port P8 register b7 b6 b5 b4 b3 b2 b1 b0 Symbol P8 Bit symbol P8_0 P8_1 P8_2 P8_3 P8_4 P8_5 P8_6 P8_7 Address 03F016 Bit name Port P80 bit Port P81 bit Port P82 bit Port P83 bit Port P84 bit Port P85 bit Port P86 bit Port P87 bit After reset Indeterminate Function The pin level on any I/O port which is set for input mode can be read by reading the corresponding bit in this register. The pin level on any I/O port which is set for output mode can be controlled by writing to the corresponding bit in this register (except for P85) 0 : "L" level 1 : "H" level RW RW RW RW RW RW RO RW RW Reserved register b7 b6 b5 b4 b3 b2 b1 b0 00 00 00 00 Symbol RSV03F4 Address 03F416 After reset Indeterminate Bit symbol (b7-b0) Bit name Reserved bits Function Must set to "0." RW RW Figure 15.8 P0 to P9 Registers Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 259 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 15. PROGRAMMABLE I/O PORTS Pull-up control register 0 (Note 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol PUR0 Bit symbol PU00 PU01 PU02 PU03 PU04 PU05 PU06 PU07 Address 03FC16 Bit name P00 to P03 pull-up P04 to P07 pull-up P10 to P13 pull-up P14 to P17 pull-up P20 to P23 pull-up P24 to P27 pull-up P30 to P33 pull-up P34 to P37 pull-up After reset 0016 Function 0 : Not pulled high 1 : Pulled high (Note 1) RW RW RW RW RW RW RW RW RW Note 1: The pin for which this bit is "1" (pulled high) and the direction bit is "0" (input mode) is pulled high. Pull-up control register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol PUR1 Bit symbol PU10 PU11 PU12 PU13 PU14 PU15 PU16 PU17 Address 03FD16 Bit name P40 to P43 pull-up P44 to P47 pull-up P50 to P53 pull-up P54 to P57 pull-up P60 to P63 pull-up P64 to P67 pull-up P72 to P73 pull-up (Note 1) P74 to P77 pull-up After reset (Note 3) 000000002 Function 0 : Not pulled high 1 : Pulled high (Note 2) RW RW RW RW RW RW RW RW RW Note 1: The P70 and P71 pins do not have pull-ups. Note 2: The pin for which this bit is "1" (pulled high) and the direction bit is "0" (input mode) is pulled high. Note 3: The values after hardware reset are as follows: * 00000000 2 when input on CNVss pin is "L" The values after software reset and watchdog timer reset are as follows: * 00000000 2 when PM 01 to PM00 bits of PM0 register are "002" (single-chip mode) Pull-up control register 2 b7 b6 b5 b4 b3 b2 b1 b0 00 Symbol PUR2 Bit symbol PU20 PU21 PU22 PU23 (b5-b4) Address 03FE16 Bit name P80 to P83 pull-up P84 to P87 pull-up (Note 2) P90 to P93 pull-up P94 to P97 pull-up Must set to "0" After reset 0016 Function 0 : Not pulled high 1 : Pulled high (Note 1) RW RW RW RW RW RW Nothing is assigned. In an attempt to write to these bits, write "0". The value, if read, turns out to be "0". Note 1: The pin for which this bit is "1" (pulled high) and the direction bit is "0" (input mode) is pulled high. Note 2: The P85 pin does not have pull-up. (b7-b6) Figure 15.9 PUR0 to PUR2 Registers Page 260 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 15. PROGRAMMABLE I/O PORTS Port control register b7 b6 b5 b4 b3 b2 b1 b0 Symbpl PCR Address 03FF16 After reset 0016 Bit symbol PCR0 Bit name Port P1 control bit Function RW Operation performed when the P1 register is read 0: When the port is set for input, the input levels of P10 to P17 RW pins are read. When set for output, the port latch is read. 1: The port latch is read regardless of whether the port is set for input or output. Nothing is assigned. In an attempt to write to these bits, (b7-b1) write "0". The value, if read, turns out to be "0". Figure 15.10 PCR Register Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 261 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 15.1 Unassigned Pin Handling in Single-chip Mode Connection 15. PROGRAMMABLE I/O PORTS Pin name Ports P0 to P7, P80 to P84, P86 to P87, P9 XOUT (Note 4) NMI (P85) AVCC AVSS After setting for input mode, connect every pin to VSS via a resistor(pull-down); or after setting for output mode, leave these pins open. (Note 1, 2 ,3) Open Connect via resistor to VCC (pull-up) Connect to VCC Connect to VSS Note 1: When setting the port for output mode and leave it open, be aware that the port remains in input mode until it is switched to output mode in a program after reset. For this reason, the voltage level on the pin becomes indeterminate, causing the power supply current to increase while the port remains in input mode. Furthermore, by considering a possibility that the contents of the direction registers could be changed by noise or noise-induced runaway, it is recommended that the contents of the direction registers be periodically reset in software, for the increased reliability of the program. Note 2: Make sure the unused pins are processed with the shortest possible wiring from the microcomputer pins (within 2 cm). Note 3: When the ports P70 and P71 are set for output mode, make sure a low-level signal is output from the pins. The ports P70 and P71 are N-channel open-drain outputs. Note 4: With external clock input to XIN pin. Microcomputer Port P0 to P9 (except for P85) (Input mode) * * (Input mode) (Output mode) * * Open NMI XOUT AVCC Open VCC AVSS VSS In single-chip mode Figure 15.11 Unassigned Pins Handling Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 262 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS 16. Electrical Characteristics Table 16.1 Symbol VCC1, VCC2 VCC1 AVCC VDD2 Supply voltage Supply voltage Analog supply voltage Analog supply voltage Input voltage RESET, CNVSS P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P85 to P87, P90 to P97, XIN, M1, STARTB P60 to P67, P70 to P77, P80 to P84 P70, P71 Output voltage VO P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P86, P87, P90 to P97, XOUT Absolute Maximum Ratings Parameter Condition V CC2=AVcc V CC1 VCC2=AVcc VCC2=VDD2 Rated value -0.3 to 6.0 -0.3 to VCC2 -0.3 to 6.0 -0.3 to 6.0 Unit V V V V VI -0.3 to VCC2 + 0.3 V -0.3 to VCC1 + 0.3 -0.3 to 6.0 V V -0.3 to VCC2 + 0.3 V P60 to P67, P70 to P77, P80 to P84 P70, P71 Pd Topr Tstg Power dissipation Operating ambient temperature Storage temperature Topr=25 C -0.3 to VCC1 + 0.3 -0.3 to 6.0 550 -20 to 70 -20 to 125 V V mW C C Note: Following setting is required: VCC1 VCC2 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 263 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 16.2 Symbol VCC1, VCC2 AVcc VDD2 V ss A V ss Supply voltage (VCC1 VCC2) Analog supply voltage Analog supply voltage Supply voltage Analog supply voltage HIGH input voltage VI H P31 to P37, P40 to P47, P50 to P57 P00 to P07, P10 to P17, P20 to P27, P30 P60 to P67, P72 to P77, P80 to P84 P85 to P87, P90 to P97 XIN, RESET, CNVSS, M1, STARTB LOW input voltage VIL P70, P71 P31 to P37, P40 to P47, P50 to P57 P00 to P07, P10 to P17, P20 to P27, P30 P60 to P67, P70 to P77, P80 to P84 P85 to P87, P90 to P97, XIN, RESET, CNVSS, M1, STARTB VCVIN IOH (peak) Composite video input voltage HIGH peak output current (Note2, Note3) HIGH average output current LOW peak output current LOW average output current CVIN, SYNCIN 16. ELECTRICAL CHARACTERISTICS Recommended Operating Conditions (Note 1) Parameter Standard Min. 2.0 Typ. 5.0 VCC2 VCC2 0 0 Max. 5.5 Unit V V V V V V V V V V V V V V V 0.8VCC2 0.8VCC2 0.8VCC1 0.8VCC2 0.8VCC1 0 0 0 0 2VP-P VCC2 VCC2 VCC1 VCC2 5.75 0.2VCC2 0.2VCC2 0.2VCC1 0.2VCC2 P00 to P07,P10 to P17, P20 to P27,P30 to P37, P40 to P47,P50 to P57, P60 to P67,P72 to P77, P80 to P84,P86,P87,P90 to P97 P00 to P07,P10 to P17, P20 to P27,P30 to P37, P40 to P47,P50 to P57, P60 to P67,P72 to P77, P80 to P84,P86,P87,P90 to P97 P00 to P07,P10 to P17, P20 to P27,P30 to P37, P40 to P47, P50 to P57, P60 to P67,P70 to P77, P80 to P84,P86,P87,P90 to P97 P00 to P07,P10 to P17, P20 to P27,P30 to P37, P40 to P47, P50 to P57, P60 to P67,P70 to P77, P80 to P84,P86,P87,P90 to P97 VCC2=2.9 to 5.5V VCC2=2.0 to 5.5V(Note 5) 0 0 32.768 - 10.0 mA IOH (avg) - 5.0 mA IOL (peak) 10.0 mA IOL (avg) 5.0 16 50 16 mA MHz kHz MHz f (XI N) f (XCIN) f (BCL K ) Main clock input oscillation frequency (Note 4) Sub-clock oscillation frequency CPU operation clock Note 1: Referenced to VCC = VCC1 = VCC2 = 2.0 to 5.5V at Topr = -20 to 70 C unless otherwise specified. Note 2: The mean output current is the mean value within 100ms. Note 3: The total IOL (peak) for ports P0, P1, P2, P3, P4, P5,P86, P87, P9 must be 80mA max. The total IOL (peak) for ports P6, P7andP80 to P84 must be 80mA max. The total IOH (peak) for ports P0, P1, and P2 must be -40mA max. The total IOH (peak) for ports P3, P4andP5 must be -40mA max. Note 4: Use the VCC1 and VCC2 power supply voltage on the following conditions. * VCC1 = 3.00V to VCC2, VCC2 = 4.00V to 5.5V (at f(XIN) = 16MHz) * VCC1 = 2.90V to VCC2, VCC2 = 2.90V to 5.5V (at f(XIN) = 16MHz, at divide-by-8 or 16) Note 5: Use in low power dissipation mode. When operating on low voltage (VCC = 3.0V), only single-chip mode can be used. If the VCC2 supply voltage is less than 2.6 V, be aware that only the CPU, RAM, clock timer, interrupt, and Input/Output ports can be used. Other control circuits (e.g., timers A and B, serial I/O, UART) cannot be used. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 264 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 16.3 Symbol - - Resolution Absolute accuracy 16. ELECTRICAL CHARACTERISTICS A/D Conversion Characteristics (Note 1) Parameter Measuring condition VREF =VCC AN0 to AN7 input VREF= ANEX0, ANEX1 input VCC = External operation amp 5V VREF =VCC=5V, oAD=10MHz 2.8 0.3 4.5 0 VCC VREF Standard Unit Min. Typ. Max. 8 3 4 Bits LSB LSB s s V V tCONV tSAMP VREF VIA Conversion time(8bit), Sample & hold function available Sampling time Reference voltage Analog input voltage Note 1: Referenced to VCC2=AVCC=VREF=4.5 to 5.5V, VSS=AVSS=0V at Topr = -20 to 70 C unless otherwise specified. Note 2: AD operation clock frequency (OAD frequency) must be 10 MHz or less. Note 3: A case without sample & hold function turn OAD frequency into 250 kHz or more. A case with sample & hold function turn OAD frequency into 1 MHz or more. Table 16.4 Symbol Flash Memory Version Electrical Characteristics (Note 1) Parameter Measuring condition Min. Standard Typ. Max 30 1 30 200 4 200 Unit s s s Word program time Block erase time Lock bit program time tps Flash memory circuit stabilization wait time 15 s Note 1: Referenced to VCC2=4.75 to 5.25V at Topr = 0 to 60 C unless otherwise specified. Table 16.5 Flash Memory Version Program/Erase Voltage and Read Operation Voltage Characteristics (Topr = 0 to 60C Flash read operation voltage VCC2 = 2.0 to 5.5 V Flash program, erase voltage VCC2 = 5.0 0.25 V Table 16.6 Symbol td(P-R) td(R-S) td(W-S) Power Supply Circuit Timing Characteristics Parameter Measuring condition Min. Standard Typ. ax. 2 150 150 Unit ms s s T e for internal power supply stabilization during powering-on im STOP release time Low power dissipation mode wait mode release time VC = 5.0V C Recommended operation voltage VCC2 td(P-R) CPU clock (a) Interrupt for stop mode release (b) Interrupt for wait mode release CPU clock (a) td(R-S) (b) td(W-S) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 265 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 16.7 Electrical Characteristics (1) (Note 1) 16. ELECTRICAL CHARACTERISTICS VCC1 = VCC2 = 5V Symbol VOH Parameter HIGH output P00 to P07, P10 to P17, P20 to P27, voltage P30 to P37, P40 to P47, P50 to P57, P86, P87, P90 to P97 P60 to P67, P72 to P77, P80 to P84 HIGH output P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, voltage P86, P87, P90 to P97 P60 to P67, P72 to P77, P80 to P84 Measuring condition IOH=-5mA IOH=-5mA Min Standard Typ. Max. VCC2 VCC1 Unit VCC2-2.0 VCC1-2.0 V V VOH IOH=-200A VCC2-0.3 VCC2 V IOH=-200A VCC=4.5V, I OH=-0.05mA VCC1-0.3 3.75 VCC2-2.0 VCC2-2.0 2.5 1.6 VCC1 V V VOH HIGH output LP3 , LP4 voltage HIGH output voltage HIGH output voltage XOUT XCOUT HIGHPOWER LOWPOWER HIGHPOWER LOWPOWER IOH=-1mA IOH=-0.5mA VCC2 VCC2 V V VOH With no load applied With no load applied IOL=5mA VOL LOW output P00 to P07, P10 to P17, P20 to P27, voltage P30 to P37, P40 to P47, P50 to P57, P86, P87, P90 to P97 P60 to P67, P70 to P77, P80 to P84 LOW output P00 to P07, P10 to P17, P20 to P27, voltage P30 to P37, P40 to P47, P50 to P57, P86, P87, P90 to P97 P60 to P67, P70 to P77, P80 to P84 2.0 V IOL=5mA 2.0 V VOL IOL=200A 0.45 V IOL=200A VCC=4.5V, I OL=0.05mA 0.45 0.4 2.0 2.0 0 0 V V V V VOL VOL LOW output LP3 to LP4 voltage LOW output voltage LOW output voltage XOUT XCOUT HIGHPOWER LOWPOWER HIGHPOWER LOWPOWER IOL=1mA IOL=0.5mA With no load applied With no load applied 0.2 VT+-VT- Hysteresis TA0IN to TA4IN, TB0IN to TB5IN, INT0 to INT5, NMI, ADTRG, CTS0 to CTS2, SCL, SDA, CLK0 to CLK4,TA2OUT to TA4OUT, RxD0 to RxD2, SIN3, SIN4 Hysteresis RESET 1.0 V VT+-VT- 0.2 2.2 V IIH HIGH input P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, current P60 to P67, P70 to P77, P80 to P87, P90 to P97 XIN, RESET, CNVss, M1, STARTB LOW input current P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P70 to P77, P80 to P87, P90 to P97 XIN, RESET, CNVss, M1, STARTB P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P72 to P77, P80 to P84, P86, P87, P90 to P97 XIN XCIN VI=5V 5.0 A I IL VI=0V -5.0 A RPULLUP Pull-up resistance VI=0V 30 50 170 k M M V R fXIN R fXCIN V RAM V SYNCIN V dat(text) fH Feedback resistance Feedback resistance RAM retention voltage Sync voltage amplitude 1.5 15 Stop mode 2.0 0.3 0.6 14.6 0.6 0.9 15.625 1.2 1.4 17.0 V V kHZ Teletext data voltage amplitude Horizontal synchronous signal frequency Note 1: Referenced to VCC =VCC1=VCC2= 4.50 to 5.50 V, VSS=0V at Topr = -20 to 70 C, f(BCLK)=16 MHz unless otherwise specified. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 266 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 16.8 Electrical Characteristics (2) (Note) 16. ELECTRICAL CHARACTERISTICS VCC1 = VCC2 = 3V Symbol V OH HIGH output voltage Parameter P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P86, P87, P90 to P97 P60 to P67, P72 to P77, P80 to P84 Measuring condition Standard Min. VCC2 - 0.5 VCC1 - 0.5 VCC2 - 0.5 VCC2 - 0.5 Typ. Max. V CC V CC V CC2 V CC2 Unit IOH = -1 mA IOH = -1 mA IOH = -0.1 mA IOH = -50 A With no load applied With no load applied V V V V OH HIGH output voltage HIGH output voltage X OUT HIGHPOWER LOWPOWER X COUT HIGHPOWER LOWPOWER 2.5 1.6 V V OL LOW output voltage P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P70 to P77, P80 to P84, P86, P87, P90 to P97 X OUT HIGHPOWER LOWPOWER IOL = 1 mA IOL = 0.1 mA IOL = 50 A With no load applied With no load applied 0.2 0.2 (0.7) 0 0 0.5 0.5 0.5 V V OL LOW output voltage LOW output voltage V X COUT HIGHPOWER LOWPOWER V V T+- V TV T+- V T- Hysteresis Hysteresis HIGH input voltage TA0IN to TA4IN , TB0IN to TB5IN, INT0 to INT5 TA2OUT to TA4OUT RESET P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P70 to P77, P80 to P87, P90 to P97 X IN , RESET, CNVss, M1, STARTB P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P70 to P77, P80 to P87, P90 to P97 X IN , RESET, CNVss, M1, STARTB P00 to P07, P10 to P17, P20 to P27, P30 to P37, P40 to P47, P50 to P57, P60 to P67, P72 to P77, P80 to P84, P86, P87, P90 to P97 X IN X CIN 0.8 1.8 V V IIH VI = 3 V 4.0 A HIGH input voltage IIL VI = 0 V -4.0 A RPULLUP Pull-up resistance VI = 0 V 50 100 3.0 25 500 k M M Feedback resistance RfXCIN Feedback resistance Note : Referenced to VCC = VCC1 = VCC2 = 3.0 V, VSS = 0 V at Topr = -20 to 70 C, f (XCIN) = 32kHz unless otherwise specified. Use in single-chip mode and low power dissipation mode. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 267 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 16.9 Symbol 16. ELECTRICAL CHARACTERISTICS Electrical Characteristics (2) (Note 1) Parameter In single-chip mode, the output pins are open and other pins are VSS Mask ROM Flash memory Flash memory Program Flash memory Erase Mask ROM Measuring condition f(BCLK)=16MHz, VCC=5.0V f(BCLK)=16MHz, VCC=5.0V f(BCLK)=16MHz, VCC =5.0V f(BCLK)=16MHz, VCC =5.0V f(XCIN)=32kHz, Low power dissipation mode, ROM(Note 3), (Note4) Vcc=5.0V f(BCLK)=32kHz, Low power dissipation mode, RAM(Note 3), (Note4) Vcc=5.0V f(BCLK)=32kHz Low power dissipation mode, Flash memory(Note 3), (Note4) Vcc=5.0V f(BCLK)=32kHz, Wait mode (Note 2), (Note4) Mask ROM Flash memory Oscillation capacity High Min. Standard Typ. 50 50 15 25 25 Max. 100 100 Unit mA mA mA mA A ICC Power supply current Flash memory 25 A 420 A 7 .5 A f(BCLK)=32kHz, Wait mode(Note 2), (Note4) Vcc=5.0V Oscillation capacity Low f(BCLK)=32kHz, Wait mode (Note 2), (Note4) Oscillation capacity High Vcc=3.0V f(BCLK)=32kHz, Wait mode(Note 2), (Note4) Vcc=3.0V Oscillation capacity Low Stop mode, (Note4) Topr=25C Vcc=5.0V 5.0 10.0 A 6.0 A 2.0 0 .8 8.0 5.0 A A Note 1: Referenced to VCC1=VCC2= 5V, VSS=0V at Topr =25 C, f(BCLK)=16MHz unless otherwise specified. Note 2: With one timer operated using fC32. (Slicer operation OFF) Note 3: This indicates the memory in which the program to be executed exists. Note 4: * All of VDD2 is at the same potential level as VCC2. * Extension registers (addresses 0016 through 3F16) are set to the initial state. * Inputs to the SYNCIN and CVIN pins are disabled. * For current consumption reducing, set the level of VSS or VCC to the ports used in input mode. Table 16.10 Symbol VIN-cu Video signal input conditions (Note 1) Parameter Measuring condition Sync-chip voltage Min Standard Typ. Max. 1.0 Unit V Composite video signal input clamp voltage Note 1: Referenced to VCC2 = 5.0 V at Topr = -20 to 70 C unless otherwise specified. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 268 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS Timing Requirements (VCC1 = VCC2 = 5V, VSS = 0V, at Topr = - 20 to 70C unless otherwise specified) Table 16.11 External Clock Input (XIN input) VCC1 = VCC2 = 5V Symbol tc tw(H) tw(L) tr tf Parameter External clock input cycle time External clock input HIGH pulse width External clock input LOW pulse width External clock rise time External clock fall time Standard Min. Max. 62.5 30 30 15 15 Unit ns ns ns ns ns Table 16.12 Remote Control Pulse Input VCC1 = VCC2 = 5V Symbol Tw(RMTH) Tw(RMTL) Parameter RMTIN input HIGH pulse width RMTIN input LOW pulse width Standard Min. Max. 61 61 Unit s s Table 16.13 JUST CLOCK Input VCC1 = VCC2 = 5V Symbol Tw(JSTH) Tw(JSTL) JSTIN input HIGH pulse width JSTIN input LOW pulse width Parameter Standard Min. Max. 61 61 Unit s s Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 269 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS Timing Requirements (VCC1 = VCC2 = 5V, VSS = 0V, at Topr = - 20 to 70C unless otherwise specified) Table 16.14 Timer A Input (Counter Input in Event Counter Mode) VCC1 = VCC2 = 5V Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Standard Min. Max. 100 40 40 Unit ns ns ns Table 16.15 Timer A Input (Gating Input in Timer Mode) VCC1 = VCC2 = 5V Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Standard Min. Max. 400 200 200 Unit ns ns ns Table 16.16 Timer A Input (External Trigger Input in One-shot Timer Mode) VCC1 = VCC2 = 5V Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Min. Standard Max. Unit ns ns ns 200 100 100 Table 16.17 Timer A Input (External Trigger Input in Pulse Width Modulation Mode) VCC1 = VCC2 = 5V Symbol tw(TAH) tw(TAL) TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Standard Min. Max. 100 100 Unit ns ns Table 16.18 Timer A Input (Counter Increment/decrement Input in Event Counter Mode) VCC1 = VCC2 = 5V Symbol tc(UP) tw(UPH) tw(UPL) tsu(UP-TIN) th(TIN-UP) TAiOUT input cycle time TAiOUT input HIGH pulse width TAiOUT input LOW pulse width TAiOUT input setup time TAiOUT input hold time Parameter Standard Min. Max. 2000 1000 1000 400 400 Unit ns ns ns ns ns Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 270 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS Timing Requirements (VCC1 = VCC2 = 5V, VSS = 0V, at Topr = - 20 to 70C unless otherwise specified) Table 16.19 Timer B Input (Counter Input in Event Counter Mode) VCC1 = VCC2 = 5V Symbol tc(TB) tw(TBH) tw(TBL) tc(TB) tw(TBH) tw(TBL) Parameter TBiIN input cycle time (counted on one edge) TBiIN input HIGH pulse width (counted on one edge) TBiIN input LOW pulse width (counted on one edge) TBiIN input HIGH pulse width (counted on both edges) TBiIN input LOW pulse width (counted on both edges) TBiIN input LOW pulse width (counted on both edges) Standard Min. Max. 100 40 40 200 80 80 Unit ns ns ns ns ns ns Table 16.20 Timer B Input (Pulse Period Measurement Mode)) VCC1 = VCC2 = 5V Symbol tc(TB) tw(TBH) tw(TBL) Parameter TBiIN input cycle time TBiIN input HIGH pulse width TBiIN input LOW pulse width Standard Min. Max. 400 200 200 Unit ns ns ns Table 16.21 Timer B Input (Pulse Width Measurement Mode)) VCC1 = VCC2 = 5V Symbol tc(TB) tw(TBH) tw(TBL) Parameter TBiIN input cycle time TBiIN input HIGH pulse width TBiIN input LOW pulse width Standard Min. Max. 400 200 200 Unit ns ns ns Table 16.22 A/D Trigger Input VCC1 = VCC2 = 5V Symbol tc(AD) tw(ADL) Parameter ADTRG input cycle time (trigger able minimum) ADTRG input LOW pulse width Standard Min. Max. 1000 125 Unit ns ns Table 16.23 Serial I/O VCC1 = VCC2 = 5V Symbol tc(CK) tw(CKH) tw(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) Parameter CLKi input cycle time CLKi input HIGH pulse width CLKi input LOW pulse width TxDi output delay time TxDi hold time RxDi input setup time RxDi input hold time Standard Min. Max. 200 100 100 80 0 30 90 Unit ns ns ns ns ns ns ns Table 16.24 External Interrupt INTi Input VCC1 = VCC2 = 5V Symbol tw(INH) tw(INL) Parameter INTi input HIGH pulse width INTi input LOW pulse width Standard Min. Max. 250 250 Unit ns ns Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 271 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS Timing Requirements (VCC1 = VCC2 = 3V, VSS = 0V, at Topr = - 20 to 70C unless otherwise specified) Table 16.25 External Clock Input (XIN Input) VCC1 = VCC2 = 3V Symbol tc tw(H) tw(L) tr tf Parameter External clock input cycle time External clock input HIGH pulse width External clock input LOW pulse width External clock rise time External clock fall time Standard Min. Max. 100 40 40 18 18 Unit ns ns ns ns ns Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 272 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS Timing Requirements (VCC1 = VCC2 = 3V, VSS = 0V, at Topr = - 20 to 70C unless otherwise specified) Table 16.26 Timer A Input (Counter Input in Event Counter Mode) VCC1 = VCC2 = 3V Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Standard Min. Max. 150 60 60 Unit ns ns ns Table 16.27 Timer A Input (Gating Input in Timer Mode) VCC1 = VCC2 = 3V Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Standard Min. Max. 600 300 300 Unit ns ns ns Table 16.28 Timer A Input (External Trigger Input in One-shot Timer Mode) VCC1 = VCC2 = 3V Symbol tc(TA) tw(TAH) tw(TAL) TAiIN input cycle time TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Min. Standard Max. Unit ns ns ns 300 150 150 Table 16.29 Timer A Input (External Trigger Input in Pulse Width Modulation Mode) VCC1 = VCC2 = 3V Symbol tw(TAH) tw(TAL) TAiIN input HIGH pulse width TAiIN input LOW pulse width Parameter Standard Min. Max. 150 150 Unit ns ns Table 16.30 Timer A Input (Counter Increment/decrement Input in Event Counter Mode) VCC1 = VCC2 = 3V Symbol tc(UP) tw(UPH) tw(UPL) tsu(UP-TIN) th(TIN-UP) TAiOUT input cycle time TAiOUT input HIGH pulse width TAiOUT input LOW pulse width TAiOUT input setup time TAiOUT input hold time Parameter Standard Min. Max. 3000 1500 1500 600 600 Unit ns ns ns ns ns Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 273 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS Timing Requirements (VCC1 = VCC2 = 3V, VSS = 0V, at Topr = - 20 to 70C unless otherwise specified) Table 16.31 Timer B Input (Counter Input in Event Counter Mode) VCC1 = VCC2 = 3V Symbol tc(TB) tw(TBH) tw(TBL) tc(TB) tw(TBH) tw(TBL) Parameter TBiIN input cycle time (counted on one edge) TBiIN input HIGH pulse width (counted on one edge) TBiIN input LOW pulse width (counted on one edge) TBiIN input cycle time (counted on both edges) TBiIN input HIGH pulse width (counted on both edges) TBiIN input LOW pulse width (counted on both edges) Standard Min. 150 60 60 300 120 120 Max. Unit ns ns ns ns ns ns Table 16.32 Timer B Input (Pulse Period Measurement Mode) VCC1 = VCC2 = 3V Symbol tc(TB) tw(TBH) tw(TBL) TBiIN input cycle time TBiIN input HIGH pulse width TBiIN input LOW pulse width Parameter Standard Min. 600 300 300 Max. Unit ns ns ns Table 16.33 Timer B Input (Pulse Period Measurement Mode) VCC1 = VCC2 = 3V Symbol tc(TB) tw(TBH) tw(TBL) TBiIN input cycle time TBiIN input HIGH pulse width TBiIN input LOW pulse width Parameter Standard Min. 600 300 300 Max. Unit ns ns ns Table 16.34 Serial I/O (Pulse Period Measurement Mode) VCC1 = VCC2 = 3V Symbol tc(CK) tw(CKH) tw(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) CLKi input cycle time CLKi input HIGH pulse width CLKi input LOW pulse width TxDi output delay time TxDi hold time RxDi input setup time RxDi input hold time 0 70 90 Parameter Standard Min. 300 150 150 160 Max. Unit ns ns ns ns ns ns ns Table 16.35 External Interrupt INTi Input (Pulse Period Measurement Mode) VCC1 = VCC2 = 3V Symbol tw(INH) tw(INL) INTi input HIGH pulse width INTi input LOW pulse width Parameter Standard Min. 380 380 Max. Unit ns ns Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 274 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS VCC1 = VCC2 = 5V tc(TA) tw(TAH) TAiIN input tw(TAL) tc(UP) tw(UPH) TAiOUT input tw(UPL) TAiOUT input (Up/down input) During event counter mode TAiIN input (When count on falling edge is selected) th(TIN-UP) tsu(UP-TIN) TAiIN input (When count on rising edge is selected) Two-phase pulse input in event counter mode TAiIN input tsu(TAIN-TAOUT) tc(TA) tsu(TAIN-TAOUT) tsu(TAOUT-TAIN) TAiOUT input tsu(TAOUT-TAIN) tc(TB) tw(TBH) TBiIN input tw(TBL) tc(AD) tw(ADL) ADTRG input Figure 16.1 Timing Diagram (1) Page 275 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS VCC1 = VCC2 = 5V tc(CK) tw(CKH) CLKi tw(CKL) TxDi td(C-Q) RxDi tw(INL) INTi input tw(INH) tsu(D-C) th(C-D) th(C-Q) Figure 16.2 Timing Diagram (2) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 276 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS VCC1 = VCC2 = 3V tc(TA) tw(TAH) TAiIN input tw(TAL) tc(UP) tw(UPH) TAiOUT input tw(UPL) TAiOUT input (Up/down input) During event counter mode TAiIN input (When count on falling edge is selected) th(TIN-UP) tsu(UP-TIN) TAiIN input (When count on rising edge is selected) Two-phase pulse input in event counter mode TAiIN input tc(TA) tsu(TAIN-TAOUT) tsu(TAIN-TAOUT) TAiOUT input tsu(TAOUT-TAIN) tsu(TAOUT-TAIN) tc(TB) tw(TBH) TBiIN input tw(TBL) tc(AD) tw(ADL) ADTRG input Figure 16.3 Timing Diagram (3) Page 277 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 16. ELECTRICAL CHARACTERISTICS VCC1 = VCC2 = 3V tc(CK) tw(CKH) CLKi tw(CKL) TxDi td(C-Q) RxDi tw(INL) INTi input tw(INH) tsu(D-C) th(C-D) th(C-Q) Figure 16.4 Timing Diagram (4) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 278 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17. Flash Memory Version 17.1 Flash Memory Performance The flash memory version is functionally the same as the mask ROM version except that it internally contains flash memory. The flash memory version has three modes-CPU rewrite, standard serial input/output, and parallel input/output modes-in which its internal flash memory can be operated on. Table 17.1 shows the outline performance of flash memory version (see Table 1.1 for the items not listed in Table 17.1.). Table 17.1 Flash Memory Version Specifications Item Flash memory operating mode Erase block User ROM area Boot ROM area Method for program Method for erasure Program, erase control method Protect method Number of commands Number of program and erasure Data Retention ROM code protection Specification 3 modes (CPU rewrite, standard serial I/O, parallel I/O) See Figure 17.1 1 block (4 Kbytes) (Note 1) In units of word Block erase Program and erase controlled by software command Protected for each block by lock bit 7 commands 100 times 10 years Parallel I/O and standard serial I/O modes are supported. Note 1: The boot ROM area contains a standard serial I/O mode rewrite control program which is stored in it when shipped from the factory. This area can only be rewritten in parallel input/output mode. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 279 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 17.2 Flash Memory Rewrite Modes Overview Standard serial I/O mode The user ROM area is rewritten by using a dedicated serial programmer. Standard serial I/O mode 1: Clock sync serial I/O Standard serial I/O mode 2: UART 17. FLASH MEMORY VERSION Flash memory CPU rewrite mode (Note 1) rewrite mode The user ROM area is rewritFunction ten by executing software commands from the CPU. EW0 mode: Can be rewritten in any area other than the flash memory (Note 2) EW1 mode: Can be rewritten in the flash memory Areas which User ROM area can be rewritten Operation Single chip mode mode Boot mode (EW0 mode) ROM None programmer Parallel I/O mode The boot ROM and user ROM areas are rewritten by using a dedicated parallel programmer. User ROM area Boot mode Serial programmer User ROM area Boot ROM area Parallel I/O mode Parallel programmer Note 1: Bit 3 of processor mode register 1 remains set to "1" while the FMR0 register FMR01 bit = 1 (CPU rewrite mode enabled). Bit 3 of processor mode register 1 is reverted to its original value by clearing the FMR01 bit to "0" (CPU rewrite mode disabled). However, if bit 3 of processor mode register 1 is changed during CPU rewrite mode, its changed value is not reflected until after the FMR01 bit is cleared to "0". Note 2: When in CPU rewrite mode, bit 0 and bit 3 in the PM1 register are set to "1". The rewrite control program can only be executed in the internal RAM. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 280 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.2 Memory Map The ROM in the flash memory version is separated between a user ROM area and a boot ROM area. Figure 17.1 shows the block diagram of flash momoery. The user ROM area is divided into several blocks, each of which can individually be protected (locked) against programming or erasure. The user ROM area can be rewritten in all of CPU rewrite, standard serial input/output, and parallel input/output modes. The boot ROM area is located at addresses that overlap the user ROM area, and can only be rewritten in parallel input/output mode. After a hardware reset that is performed by applying a high-level signal to the CNVSS and P50 pins and a low-level signal to the M1 pin, the program in the boot ROM area is executed. After a hardware reset that is performed by applying a low-level signal to the CNVSS pin, the program in the user ROM area is executed (but the boot ROM area cannot be read). 0C000016 Block 8 : 64K bytes 0F000016 0D000016 Block 7 : 64K bytes Block 5 : 32K bytes 0E000016 Block 6 : 64K bytes 0EFFFF16 0F000016 Block 0 to Block 5 (32+8+8+8 +4+4)K bytes 0FFFFF16 User ROM area 0F7FFF16 0F800016 Block 4 : 8K bytes 0F9FFF16 0FA00016 Block 3 : 8K bytes 0FBFFF16 0FC00016 Block 2 : 8K bytes 0FDFFF16 0FE00016 0FEFFF16 0FF00016 0FFFFF16 Block 1 : 4K bytes Block 0 : 4K bytes 0FF00016 0FFFFF16 4K bytes Boot ROM area (Note 1) Note 1: The boot ROM area can only be rewritten in parallel input/output mode. Note 2: To specify a block, use an even address in that block. Note 3: Shown here is a block diagram during single-chip mode. Figure 17.1 Flash Memory Block Diagram Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 281 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.3 Boot Mode After a hardware reset which is performed by applying a low-level signal to the M1 pin and a high-level signal to the CNVSS and P50 pins, the microcomputer is placed in boot mode, thereby executing the program in the boot ROM area. During boot mode, the boot ROM and user ROM areas are switched over by the FMR05 bit in the FMR0 register. The boot ROM area contains a standard serial input/output mode based rewrite control program which was stored in it when shipped from the factory. The boot ROM area can be rewritten in parallel input/output mode. Prepare an EW0 mode based rewrite control program and write it in the boot ROM area, and the flash memory can be rewritten as suitable for the system. 17.4 Functions To Prevent Flash Memory from Rewriting To prevent the flash memory from being read or rewritten easily, parallel input/output mode has a ROM code protect and standard serial input/output mode has an ID code check function. 17.4.1 ROM Code Protect Function The ROM code protect function inhibits the flash memory from being read or rewritten during parallel input/ output mode. Figure 17.2 shows the ROMCP register. The ROMCP register is located in the user ROM area. The ROMCP1 bit consists of two bits. The ROM code protect function is enabled by clearing one or both of two ROMCP1 bits to "0" when the ROMCR bits are not `002,' with the flash memory thereby protected against reading or rewriting. Conversely, when the ROMCR bits are `002' (ROM code protect removed), the flash memory can be read or rewritten. Once the ROM code protect function is enabled, the ROMCR bits cannot be changed during parallel input/output mode. Therefore, use standard serial input/output or other modes to rewrite the flash memory. 17.4.2 ID Code Check Function Use this function in standard serial input/output mode. Unless the flash memory is blank, the ID codes sent from the programmer and the ID codes written in the flash memory are compared to see if they match. If the ID codes do not match, the commands sent from the programmer are not accepted. The ID code consists of 8-bit data, the areas of which, beginning with the first byte, are 0FFFDF16, 0FFFE316, 0FFFEB16, 0FFFEF16, 0FFFF316, 0FFFF716, and 0FFFFB16. Prepare a program in which the ID codes are preset at these addresses and write it in the flash memory. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 282 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION ROM code protect control address b7 b6 b5 b4 b3 b2 b1 b0 1 1 1 1 Symbol ROMCP Address 0FFFFF16 Value when shipped FF16 (Note 4) Bit symbol Bit name Reserved bit Reserved bit Reserved bit Reserved bit Function Set this bit to "1" Set this bit to "1" Set this bit to "1" Set this bit to "1" b5 b4 RW RW RW RW RW RW RW RW RW ROMCR ROM code protect reset bit (Note 2, Note 4) 00: Removes protect 01: 10: Enables ROMCP1 bit 11: } } ROMCP1 ROM code protect level 1 set bit (Note 1, Note 3, Note 4) b7 b6 00: Protect enabled 01: 10: 11: Protect disabled Note 1: If the ROMCR bits are set to other than "002" and the ROMCP1 bits are set to other than "112" (ROM code protect enabled), the flash memory is disabled against reading and rewriting in parallel input/output mode. Note 2: If the ROMCR bits are set to "002," ROM code protect level 1 is removed. However, because the ROMCR bits cannot be modified during parallel input/output mode, they need to be modified in standard serial input/output or other modes. Note 3: The ROMCP1 bits are effective when the ROMCR bits are "012," "102," or "112." Note 4: Once any of these bits is cleared to "0", it cannot be set back to "1". If a memory block that contains the ROMCP register is erased, the ROMCP register is set to "FF16." Figure 17.2 ROMCP Register Address 0FFFDF16 to 0FFFDC16 ID1 0FFFE316 to 0FFFE016 0FFFE716 to 0FFFE416 0FFFEB16 to 0FFFE816 ID3 ID2 Undefined instruction vector Overflow vector BRK instruction vector Address match vector Single step vector Watchdog timer vector DBC vector NMI vector 0FFFEF16 to 0FFFEC16 ID4 0FFFF316 to 0FFFF016 0FFFF716 to 0FFFF416 0FFFFB16 to 0FFFF816 0FFFFF16 to 0FFFFC16 ID5 ID6 ID7 ROMCP Reset vector 4 bytes Figure 17.3 Address for ID Code Stored Page 283 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.5 CPU Rewrite Mode In CPU rewrite mode, the user ROM area can be rewritten by executing software commands from the CPU. Therefore, the user ROM area can be rewritten directly while the microcomputer is mounted on-board without having to use a ROM programmer, etc. In CPU rewrite mode, only the user ROM area shown in Figure 17.1 can be rewritten and the boot ROM area cannot be rewritten. Make sure the Program and the Block Erase commands are executed only on each block in the user ROM area. During CPU rewrite mode, the user ROM area be operated on in either Erase Write 0 (EW0) mode or Erase Write 1 (EW1) mode. Table 17.3 lists the differences between Erase Write 0 (EW0) and Erase Write 1 (EW1) modes. Table 17.3 EW0 Mode and EW1 Mode EW0 mode * Single chip mode * Boot mode * User ROM area * Boot ROM area EW1 mode Single chip mode User ROM area Item Operation mode Areas in which a rewrite control program can be located Areas in which a rewrite control program can be executed Areas which can be rewritten Software command limitations Modes after Program or Erase CPU status during Auto Write and Auto Erase Flash memory status detection Must be transferred to any area other Can be executed directly in the user than the flash memory (RAM) ROM area before being executed (Note 2) User ROM area User ROM area However, this does not include the area in which a rewrite control program exists None * Program, Block Erase command Cannot be executed on any block in which a rewrite control program exists * Read Status Register command Cannot be executed Read Status Register mode Read Array mode Operating Hold state (I/O ports retain the state in which they were before the command was executed)(Note 1) Read the FMR0 register's FMR00, FMR06, and FMR07 bits in a program * Read the FMR0 register's FMR00, FMR06, and FMR07 bits in a program * Execute the Read Status Register command to read the status register's SR7, SR5, and SR4 flags. _______ Note 1: Make sure no interrupts (except NMI and watchdog timer interrupts) and DMA transfers will occur. Note 2: When in CPU rewrite mode, bit 0 and bit 3 in the PM1 register are set to "1". The rewrite control program can only be executed in the internal RAM. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 284 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.5.1 EW0 Mode The microcomputer is placed in CPU rewrite mode by setting the FMR0 register's FMR01 bit to "1" (CPU rewrite mode enabled), ready to accept commands. In this case, because the FMR1 register's FMR11 bit = 0, EW0 mode is selected. The FMR01 bit can be set to "1" by writing "0" and then "1" in succession. Use software commands to control program and erase operations. Read the FMR0 register or status register to check the status of program or erase operation at completion. 17.5.2 EW1 Mode EW1 mode is selected by setting FMR11 bit to "1" (by writing "0" and then "1" in succession) after setting the FMR01 bit to "1" (by writing "0" and then "1" in succession). Read the FMR0 register to check the status of program or erase operation at completion. The status register cannot be read during EW1 mode. Figure 17.4 shows the FMR0 and FMR1 registers. Registers FMR0 and FMR1 are shown in Figure 17.4. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 285 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION FMR00 Bit This bit indicates the operating status of the flash memory. The bit is "0" when the Program, Erase, or Lock Bit program is running; otherwise, the bit is "1". FMR01 Bit The microcomputer is made ready to accept commands by setting the FMR01 bit to "1" (CPU rewrite mode). During boot mode, make sure the FMR05 bit also is "1" (user ROM area access). FMR02 Bit The lock bit set for each block can be disabled by setting the FMR02 bit to "1" (lock bit disabled). (Refer to the description of the data protect function.) The lock bits set are enabled by setting the FMR02 bit to "0". The FMR02 bit only disables the lock bit function and does not modify the lock bit data (lock bit status flag). However, if the Erase command is executed while the FMR02 bit is set to "1", the lock bit data changes state from "0" (locked) to "1" (unlocked) after Erase is completed. FMSTP Bit This bit is provided for initializing the flash memory control circuits, as well as for reducing the amount of current consumed in the flash memory. The internal flash memory is disabled against access by setting the FMSTP bit to "1". Therefore, make sure the FMSTP bit is modified in other than the flash memory. In the following cases, set the FMSTP bit to "1": * . When flash memory access resulted in an error while erasing or programming in EW0 mode (FMR00 bit not reset to "1" (ready)) * . When entering low power mode Figure 17.7 shows a flow chart to be followed before and after entering low power mode. Note that when going to stop or wait mode, the FMR0 register does not need to be set because the power for the internal flash memory is automatically turned off and is turned back on again after returning from stop or wait mode. FMR05 Bit This bit switches between the boot ROM and user ROM areas during boot mode. Set this bit to "0" when accessing the boot ROM area (for read) or "1" (user ROM access) when accessing the user ROM area (for read, write, or erase). FMR06 Bit This is a read-only bit indicating the status of auto program operation. The bit is set to "1" when a program error occurs; otherwise, it is cleared to "0". For details, refer to the description of the full status check. FMR07 Bit This is a read-only bit indicating the status of auto erase operation. The bit is set to "1" when an erase error occurs; otherwise, it is cleared to "0". For details, refer to the description of the full status check. Figure 17.5 and 17.6 show the setting and resetting of EW0 mode and EW1 mode, respectively. FMR11 Bit Setting this bit to "1" places the microcomputer in EW1 mode. FMR16 Bit This is a read-only bit indicating the execution result of the Read Lock Bit Status command. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 286 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION Flash memory control register 0 b7 b6 b5 b4 b3 b2 b1 b0 Symbol FMR0 Bit symbol FMR00 FMR01 Address 01B716 After reset XX0000012 0 Bit name RY/BY status flag CPU rewrite mode select bit (Note 1) Function 0: Busy (being written or erased) 1: Ready 0: Disables CPU rewrite mode 1: Enables CPU rewrite mode 0: Enables lock bit 1: Disables lock bit 0: Enables flash memory operation 1: Stops flash memory operation (placed in low power mode, flash memory initialized) Must always be set to "0" 0: Boot ROM area is accessed 1: User ROM area is accessed 0: Terminated normally 1: Terminated in error 0: Terminated normally 1: Terminated in error RW RO RW FMR02 Lock bit disable select bit (Note 2) RW FMSTP Flash memory stop bit (Note 3, Note 5)) RW RW RW RO RO (b4) FMR05 Reserved bit User ROM area select bit (Note 3) (Effective in only boot mode) Program status flag (Note 4) Erase status flag (Note 4) FMR06 FMR07 Note 1: To set this bit to "1", write "0" and then "1" in succession. Make sure no interrupts or DMA transfers will occur before writing "1" after writing "0". Write to this bit when the NMI pin is in the high state. Also, while in EW0 mode, modify this bit in other than the flash memory. Note 2: To set this bit to "1", write "0" and then "1" in succession when the FMR01 bit = 1. Make sure no interrupts or no DMA transfers will occur before writing "1" after writing "0". Note 3: modify this bit in other than the flash memory. Note 4: This flag is cleared to "0" by executing the Clear Status command. Note 5: Effective when the FMR01 bit = 1 (CPU rewrite mode). If the FMR01 bit = 0, although the FMSTP bit can be set to "1" by writing "1" in a program, the flash memory is neither placed in low power mode nor initialized. Note 6: This status includes writing or reading with the Lock Bit Program or Read Lock Bit Status command. Flash memory control register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol FMR1 Bit symbol (b0) FMR11 Address 01B516 After reset 0X00XX0X2 0 0 0 0 Bit name Reserved bit EW1 mode select bit (Note) Reserved bit Reserved bit Lock bit status flag Reserved bit Function The value in this bit when read is indeterminate. 0: EW0 mode 1: EW1 mode The value in this bit when read is indeterminate. Must always be set to "0" 0: Lock 1: Unlock Must always be set to "0" RW RO RW RO RW RO RW (b3-b2) (b5-b4) FMR16 (b7) Note : To set this bit to "1", write "0" and then "1" in succession when the FMR01 bit = 1. Make sure no interrupts or no DMA transfers will occur before writing "1" after writing "0". Write this bit in the state the NMI pin = "H". The FMR01 and FMR11 bits both are cleared to "0" by setting the FMR01 bit to "0". Figure 17.4 FMR0 and FMR1 Registers Page 287 of 326 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION EW0 mode operation procedure Rewrite control program Single-chip mode, or boot mode For only boot mode set the FMR05 bit to "1" (user ROM area access) Set CM0, CM1, and PM1 registers (Note 1) Set the FMR01 bit by writing "0" and then "1" (CPU rewrite mode enabled) (Note 2) Transfer a rewrite control program to any area other than the flash memory (Note 5) Execute software commands Jump to the rewrite control program which has been transferred to any area other than the flash memory (The subsequent processing is executed by the rewrite control program in any area other than the flash memory) Execute the Read Array command (Note 3) Write "0" to the FMR01 bit (CPU rewrite mode disabled) For only boot mode Write "0" to the FMR05 bit (Boot ROM area accessed) (Note 4) Jump to a specified address in the flash memory Note 1: Select 10 MHz or less for CPU clock using the CM0 register's CM06 bit and CM1 register's CM17 to 6 bits. Also, set the PM1 register's PM17 bit to "1" (with wait state). Note 2: To set the FMR01 bit to "1", write "0" and then "1" in succession. Make sure no interrupts or no DMA transfers will occur before writing "1" after writing "0". Write to the FMR01 bit from a program in other than the flash memory. Also write only when the NMI pin is "H" level. Note 3: Disables the CPU rewrite mode after executing the Read Array command. Note 4: User ROM area is accessed when the FMR05 bit is set to "1". Note 5: When in CPU rewrite mode, bit 0 and bit 3 in the PM1 register are set to "1". The rewrite control program can only be executed in the internal RAM or in an external area that is enabled for use when the PM13 bit = 1. Figure 17.5 Setting and Resetting of EW0 Mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 288 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION EW1 mode operation procedure Program in ROM Single-chip mode (Note 1) Set CM0, CM1, and PM1 registers (Note 2) Set the FMR01 bit by writing "0" and then "1" (CPU rewrite mode enabled) Set the FMR11 bit by writing "0" and then "1" (EW1 mode) (Note 3) Execute software commands Write "0" to the FMR01 bit (CPU rewrite mode disabled) Note 1: In EW1 mode, do not set the microcomputer in boot mode. Note 2: Select 10 MHz or less for CPU clock using the CM0 register's CM06 bit and CM1 register's CM17 to 6 bits. Also, set the PM1 register's PM17 bit to "1" (with wait state). Note 3: To set the FMR01 bit to "1", write "0" and then "1" in succession. Make sure no interrupts or no DMA transfers will occur before writing "1" after writing "0". Write to the FMR01 bit from a program in other than the flash memory. Also write only when the NMI pin is "H" level. Figure 17.6 Setting and Resetting of EW1 Mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 289 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION Low power dissipation mode program Transfer a low power dissipation mode program to any area other the flash memory Set the FMR01 bit by writing "0" and then "1" (CPU rewrite mode enabled) Jump to the low power dissipation mode program which has been transferred to any area other the flash memory. (The subsequent processing is executed by a program in any area other than the flash memory.) Set FMSTP bit to "1" (flash memory stopped. Low power state)(Note 1) Switch the clock source for CPU clock. Turn main clock off. (Note 2) Process of low power dissipation mode Turn main clock on wait until oscillation stabilizes switch the clock source for CPU clock (Note 2) Set the FMSTP bit to "0" (flash memory operation) Write "0" to the FMR01 bit (CPU rewrite mode disabled) Wait until the flash memory circuit stabilizes (tps) (Note 3) Jump to a specified address in the flash memory Note 1: Set the FMSTP bit to 1 after setting the FMR01 bit to "1". Note 2: Before the clock source for CPU clock can be changed to main clock or sub clock, the clock to which to be changed must be stable. Note 3: Insert a tps wait time in a program. The flash memory cannot be accessed during this wait time. Figure 17.7 Processing Before and After Low Power Dissipation Mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 290 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.5.3 Precautions on CPU Rewrite Mode Described below are the precautions to be observed when rewriting the flash memory in CPU rewrite mode. (1) Operation Speed Before entering CPU rewrite mode (EW0 or EW1 mode), select 10 MHz or less for BCLK using the CM06 bit in the CM0 register and the CM17 to CM16 bits in the CM1 register. Also, set the PM17 bit in the PM1 register to "1" (with wait state). (2) Instructions to Prevent from Using The following instructions cannot be used in EW0 mode because the flash memory's internal data is referenced: UND instruction, INTO instruction, JMPS instruction, JSRS instruction, and BRK instruction. (3) Interrupts EW0 Mode *Any interrupt which has a vector in the variable vector table can be used providing that its vector is transferred into the RAM area. *The NMI and watchdog timer interrupts can be used because the FMR0 register and FMR1 register are initialized when one of those interrupts occurs. The jump addresses for those interrupt service routines should be set in the fixed vector table. Because the rewrite operation is halted when a NMI or watchdog timer interrupt occurs, the rewrite program must be executed again after exiting the interrupt service routine. *The address match interrupt cannot be used because the flash memory's internal data is referenced. EW1 Mode *Make sure that any interrupt which has a vector in the variable vector table or address match interrupt will not be accepted during the auto program or auto erase period. *Avoid using watchdog timer interrupts. *The NMI interrupt can be used because the FMR0 register and FMR1 register are initialized when this interrupt occurs. The jump address for the interrupt service routine should be set in the fixed vector table. Because the rewrite operation is halted when a NMI interrupt occurs, the rewrite program must be executed again after exiting the interrupt service routine. (4) How to Access To set the FMR01, FMR02, or FMR11 bit to "1", write "0" and then "1" in succession. This is necessary to ensure that no interrupts or DMA transfers will occur before writing "1" after writing "0". Also only when NMI pin is "H" level. (5) Writing in the User ROM Space EW0 Mode *If the power supply voltage drops while rewriting any block in which the rewrite control program is stored, a problem may occur that the rewrite control program is not correctly rewritten and, consequently, the flash memory becomes unable to be rewritten thereafter. In this case, standard serial I/O or parallel I/O mode should be used. EW1 Mode *Avoid rewriting any block in which the rewrite control program is stored. (6) DMA Transfer In EW1 mode, make sure that no DMA transfers will occur while the FMR0 registerAfs FMR00 bit = 0 (during the auto program or auto erase period). Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 291 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP (7) Writing Command and Data Write the command code and data at even addresses. 17. FLASH MEMORY VERSION (8) Wait Mode When shifting to wait mode, set the FMR01 bit to "0" (CPU rewrite mode disabled) before executing the WAIT instruction. (9) Stop Mode When shifting to stop mode, the following settings are required: *Set the FMR01 bit to "0" (CPU rewrite mode disabled) and disable DMA transfers before setting the CM10 bit to "1" (stop mode). *Execute the JMP.B instruction subsequent to the instruction which sets the CM10 bit to "1" (stop mode) Example program L1: Program after returning from stop mode (10) Low Power Dissipation Mode If the CM05 bit is set to "1" (main clock stop), the following commands must not be executed. BSET JMP.B 0, CM1 L1 ; Stop mode *Program *Block erase *Lock bit program Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 292 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.5.4 Software Commands Software commands are described below. The command code and data must be read and written in 16-bit units, to and from even addresses in the user ROM area. When writing command code, the 8 high order bits (D1t-D8) are ignored. Table 17.4 Software Commands First bus cycle Command Read array Read status register Clear status register Program Block erase Lock bit program Read lock bit status Mode Write Write Write Write Write Write Write Address X X X WA X BA X Data (D0 to D15) xxFF16 xx7016 xx5016 xx4016 xx2016 xx7716 xx7116 Write Write Write Write WA BA BA BA WD xxD016 xxD016 xxD016 Read X SRD Mode Second bus cycle Address Data (D0 to D7) SRD: Status register data (D7 to D0) WA: Write address (Make sure the address value specified in the the first bus cycle is the same even address as the write address specified in the second bus cycle.) WD: Write data (16 bits) BA: Uppermost block address (even address, however) X: Any even address in the user ROM area xx: High-order 8 bits of command code (ignored) Read Array Command (FF16) This command reads the flash memory. Writing `exxFF16' in the first bus cycle places the microcomputer in read array mode. Enter the read address in the next or subsequent bus cycles, and the content of the specified address can be read in 16-bit units. Because the microcomputer remains in read array mode until another command is written, the contents of multiple addresses can be read in succession. Read Status Register Command (7016) This command reads the status register. Write `exx7016' in the first bus cycle, and the status register can be read in the second bus cycle. (Refer to "Status Register.") When reading the status register too, specify an even address in the user ROM area. Do not execute this command in EW1 mode. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 293 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION Clear Status Register Command This command clears the status register to "0". Write `exx5016' in the first bus cycle, and the FMR06 to FMR07 bits in the FMR0 register and SR4 to SR5 in the status register will be cleared to "0". Program Command This command writes data to the flash memory in 1 word (2 byte) units. Write `exx4016' in the first bus cycle and write data to the write address in the second bus cycle, and an auto program operation (data program and verify) will start. Make sure the address value specified in the first bus cycle is the same even address as the write address specified in the second bus cycle. Check the FMR00 bit in the FMR0 register to see if auto programming has finished. The FMR00 bit is "0" during auto programming and set to "1" when auto programming is completed. Check the FMR06 bit in the FMR0 register after auto programming has finished, and the result of auto programming can be known. (Refer to "Full Status Check.") Each block can be protected against programming by a lock bit. (Refer to "Data Protect Function.") Be careful not to write over the already programmed addresses. In EW1 mode, do not execute this command on any address at which the rewrite control program is located. In EW0 mode, the microcomputer goes to read status register mode at the same time auto programming starts, making it possible to read the status register. The status register bit 7 (SR7) is cleared to "0" at the same time auto programming starts, and set back to "1" when auto programming finishes. In this case, the microcomputer remains in read status register mode until a read command is written next. The result of auto programming can be known by reading the status register after auto programming has finished. Start Write the command code `xx4016' to the write address Write data to the write address FMR00=1? YES Full status check NO Program completed Note: Write the command code and data at even number. Figure 17.8 Program Command Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 294 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION Block Erase Write `exx2016' in the first bus cycle and write `exxD016' to the uppermost address of a block (even address, however) in the second bus cycle, and an auto erase operation (erase and verify) will start. Check the FMR0 register's FMR00 bit to see if auto erasing has finished. The FMR00 bit is "0" during auto erasing and set to "1" when auto erasing is completed. Check the FMR0 register's FMR07 bit after auto erasing has finished, and the result of auto erasing can be known. (Refer to "Full Status Check.") Figure 17.9 shows an example of a block erase flowchart. Each block can be protected against erasing by a lock bit. (Refer to "Data Protect Function.") In EW1 mode, do not execute this command on any address at which the rewrite control program is located. In EW0 mode, the microcomputer goes to read status register mode at the same time auto erasing starts, making it possible to read the status register. The status register bit 7 (SR7) is cleared to "0" at the same time auto erasing starts, and set back to "1" when auto erasing finishes. In this case, the microcomputer remains in read status register mode until the Read Array or Read Lock Bit Status command is written next. Start Write the command code `xx2016' Write `xxD016' to the uppermost block address FMR00=1? YES Full status check NO Block erase completed Note: Write the command code and data at even number. Figure 17.9 Block Erase Command Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 295 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION Lock Bit Program Command This command sets the lock bit for a specified block to "0" (locked). Write `exx7716' in the first bus cycle and write `exxD016' to the uppermost address of a block (even address, however) in the second bus cycle, and the lock bit for the specified block is cleared to "0". Make sure the address value specified in the first bus cycle is the same uppermost block address that is specified in the second bus cycle. Figure 17.10 shows an example of a lock bit program flowchart. The lock bit status (lock bit data) can be read using the Read Lock Bit Status command. Check the FMR0 register's FMR00 bit to see if writing has finished. For details about the lock bit function, and on how to set the lock bit to "1", refer to "Data Protect Function." Start Write command code `xx7716' to the uppermost block address Write `xxD016' to the uppermost block address FMR00=1? YES Full status check NO Lock bit program completed Note: Write the command code and data at even number. Figure 17.10 Lock Bit Program Command Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 296 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION Read Lock Bit Status Command This command reads the lock bit status of a specified block. Write `exx7116' in the first bus cycle and write `exxD016' to the uppermost address of a block (even address, however) in the second bus cycle, and the lock bit status of the specified block is stored in the FMR1 register's FMR16 bit. Read the FMR16 bit after the FMR0 register's FMR00 bit is set to "1" (ready). Figure 17.11 shows an example of a read lock bit status flowchart. Start Write the command code `xx7116' Write `xxD016' to the uppermost block address FMR00=1? YES FMR16=0? YES Locked NO NO Not locked Note: Write the command code and data at even number. Figure 17.11 Read Lock Bit Status Command Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 297 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.6 Data Protect Function Each block in the flash memory has a nonvolatile lock bit. The lock bit is effective when the FMR02 bit = 0 (lock bit enabled). The lock bit allows each block to be individually protected (locked) against programming and erasure. This helps to prevent data from inadvertently written to or erased from the flash memory. The following shows the relationship between the lock bit and the block status. * When the lock bit = 0, the block is locked (protected against programming and erasure). * When the lock bit = 1, the block is not locked (can be programmed or erased). The lock bit is cleared to "0" (locked) by executing the Lock Bit Program command, and is set to "1" (unlocked) by erasing the block. The lock bit cannot be set to "1" by a command. The lock bit status can be read using the Read Lock Bit Status command. The lock bit function is disabled by setting the FMR02 bit to "1", with all blocks placed in an unlocked state. (The lock bit data itself does not change state.) Setting the FMR02 bit to "0" enables the lock bit function (lock bit data retained). If the Block Erase command is executed while the FMR02 bit = 1, the target block or all blocks are erased irrespective of how the lock bit is set. The lock bit for each block is set to "1" after completion of erasure. For details about the commands, refer to "Software Commands." 17.7 Status Register The status register indicates the operating status of the flash memory and whether an erase or programming operation terminated normally or in error. The status of the status register can be known by reading the FMR0 register's FMR00, FMR06, and FMR07 bits. Table 17.5 shows the status register. In EW0 mode, the status register can be read in the following cases: (1) When a given even address in the user ROM area is read after writing the Read Status Register command (2) When a given even address in the user ROM area is read after executing the Program, Block Erase, or Lock Bit Program command but before executing the Read Array command. Sequencer Status (SR7 and FMR00 Bits ) The sequence status indicates the operating status of the flash memory. SR7 = 0 (busy) during auto programming, auto erase, and lock bit write, and is set to "1" (ready) at the same time the operation finishes. Erase Status (SR5 and FMR07 Bits) Refer to "Full Status Check." Program Status (SR4 and FMR06 Bits) Refer to "Full Status Check." Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 298 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 17.5 Status Register 17. FLASH MEMORY VERSION Status register bit SR7 (D7) SR6 (D6) SR5 (D5) SR4 (D4) SR3 (D3) SR2 (D2) SR1 (D1) SR0 (D0) FMR0 register bit FMR00 Status name "0" Sequencer status Reserved Busy - Contents "1" Ready Terminated in error Terminated in error - Value after reset 1 FMR07 FMR06 Erase status Program status Reserved Reserved Reserved Reserved Terminated normally Terminated normally - 0 0 * D0 to D7: Indicates the data bus which is read out when the Read Status Register command is executed. * The FMR07 bit (SR5) and FMR06 bit (SR4) are cleared to "0" by executing the Clear Status Register command. * When the FMR07 bit (SR5) or FMR06 bit (SR4) = 1, the Program, Block Erase, and Lock Bit Program commands are not accepted. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 299 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.8 Full Status Check When an error occurs, the FMR0 register's FMR06 to FMR07 bits are set to "1", indicating occurrence of each specific error. Therefore, execution results can be verified by checking these status bits (full status check). Table 17.6 lists errors and FMR0 register status. Figure 17.12 shows a full status check flowchart and the action to be taken when each error occurs. Table 17.6 Errors and FMR0 Register Status FRM00 register (status register) status FMR07 (SR5) 1 FMR06 (SR4) 1 Error Error occurence condition Command * When any command is not written correctly sequence error * When invalid data was written other than those that can be written in the second bus cycle of the Lock Bit Program or Block Erase command (i.e., other than `xxD016' or `xxFF16') (Note 1) Erase error * When the Block Erase command was executed on locked blocks (Note 2) * When the Block Erase command was executed on unlocked blocks but the blocks were not automatically erased correctly * When the Program command was executed on locked blocks (Note 2) * When the Program command was executed on unlocked blocks but the blocks were not automatically programmed correctly. * When the Lock Bit Program command was executed but not programmed correctly 1 0 0 1 Program error Note 1: If "xxFF16" is written by the 2nd bus cycle of these commands, it will become lead array mode and the command code written by the 1st bus cycle will become invalid simultaneously. Note 2: When FMR02 bit is "1" (lock bit is invalid), an error is not generated on these conditions. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 300 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION Full status check FMR06 =1 and FMR07=1? YES Command sequence error (1) Execute the Clear Status Register command to clear these status flags to "0". (2) Reexecute the command after checking that it is entered correctly. NO NO (1) Execute the Clear Status Register command to clear the erase status flag to "0". (2) Execute the Read Lock Bit Status command to see if the lock bit for the block in error is "0". If so, set the FMR0 register's FMR02 bit to "1". (3) Reexecute the Block Erase command. Note 1: If the error still occurs, the block in error cannot be used. Furthermore, if the lock bit = 1 in (2) above, the block in error cannot be used either. FMR07= 0? YES Erase error FMR06= 0? YES NO Program error [During programming] (1) Execute the Clear Status Register command to clear the program status flag to "0". (2) Execute the Read Lock Bit Status command to see if the lock bit for the block in error is "0". If so, set the FMR0 register's FMR02 bit to "1". (3) Reexecute the Program command. Note 2: If the error still occurs, the block in error cannot be used. Furthermore, if the lock bit = 1 in (2) above, the block in error cannot be used either. [During lock bit programming] (1) Execute the Clear Status Register command to clear the program status flag to "0". (2) Set the FMR0 register's FMR02 bit to "1". (3) Execute the Block Erase command to erase the block in error. (4) Reexecute the Lock Bit command. Note 3: If the error still occurs, the block in error cannot be used. Full status check completed Note 4: If FMR06 or FMR07 = 1, any of the Program, Block Erase, Lock Bit Program, or Read Lock Bit Status command is not accepted. Execute the Clear Status Register command before executing those commands. Figure 17.12 Full Status Check and Handling Procedure for Each Error Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 301 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.9 Standard Serial I/O Mode In standard serial input/output mode, the user ROM area can be rewritten while the microcomputer is mounted onboard by using a serial programmer suitable for M306H7FGFP. For more information about serial programmers, contact the manufacturer of your serial programmer. For details on how to use, refer to the user's manual included with your serial programmer. Table 17.7 lists pin functions (flash memory standard serial input/output mode). Figures 17.13 show pin connections for serial input/output mode. 17.9.1 ID Code Check Function This function determines whether the ID codes sent from the serial programmer and those written in the flash memory match. (Refer to the description of the functions to inhibit rewriting flash memory version.) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 302 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP Table 17.7 Pin VCC1, VCC2, VSS CNVSS RESET M1 STARTB XIN XOUT AVCC, AV SS P00 to P07 P10 to P17 P20 to P27 P30 to P37 P40 to P47 P5 P51 to P57 P50 P60 to P63 P64/RTS1 P6 P65/CLK1 P66/RXD1 P67/TXD1 P70 to P77 P80 to P84, P86, P87 P85/NM1 P90 to P97 VDD2, Vss2 LP3, LP4 CVIN1, SYNCIN VCCOFF SCLK input RxD input TxD output Input port P7 Input port P8 NMI input Input port P9 Power input Filter output Compound video input VCC1 faction power supply input switch O I I I I O I I I I 17. FLASH MEMORY VERSION Pin Functions (Flash Memory Standard Serial I/O Mode) Name Power input CNVSS Reset input Mode select Oscillation selection input Clock input Clock output Analog power supply input Input port P0 Input port P1 Input port P2 Input port P3 Input port P4 Input port P5 CE input Input port P6 BUSY output I I I I I I I I O I I I I I O I/O Description Input VCC1 to VCC1 pin. Input 4.75 to 5.25V to VCC2 pin. Input condition is VCC1 VCC2. Connect to VCC2 pin. Reset input pin. While RESET pin is "L" level, input a 20 cycle or longer clock to XIN pin. Connect to VSS pin. Connect to VSS pin. Connect a ceramic resonator or crystal oscillator between XIN and XOUT pins. To input an externally generated clock, input it to X IN pin and open XOUT pin. Connect AVss to Vss and AVcc to VCC2, respectively Apply VCC2 to AVcc pin and 0V to AVSS pin.. Input "H" or "L" level signal or open. Input "H" or "L" level signal or open. Input "H" or "L" level signal or open. Input "H" or "L" level signal or open. Input "H" or "L" level signal or open. Input "H" or "L" level signal or open. Input "H" level signal. Input "H" or "L" level signal or open. Standard serial I/O mode 1: BUSY signal output pin Standard serial I/O mode 2: Monitors the boot program operation check signal output pin. Standard serial I/O mode 1: Serial clock input pin Standard serial I/O mode 2: Input "L". Serial data input pin Serial data output pin (Note 1) Input "H" or "L" level signal or open. Input "H" or "L" level signal or open. Connect this pin to VCC2. Input "H" or "L" level signal or open. Connect VDD2 pin to VCC2 and connect VSS2 pin to VSS. Apply VCC2 to VDD2 pin and 0V to VSS2 pin. Open Input "H" or "L" level signal or open. Input "L" level signal. ___________ Note 1: When using standard serial input/output mode 1, the TxD pin must be held high while the RESET pin is pulled low. Therefore, connect this pin to VCC1 via a resistor. Because this pin is directed for data output after reset, adjust the pull-up resistance value in the system so that data transfers will not be affected. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 303 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION VSS P1_5/INT3 P1_6/INT4 P1_7/INT5 P3_0 VCC P3_1 P3_2 P1_0 P1_1 P1_2 P1_3 P1_4 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7 P3_3 P3_4 P3_5 P3_6 P3_7 P4_0 P4_1 P4_2 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 P0_7/AN7 P0_6/AN6 P0_5/AN5 P0_4/AN4 P0_3/AN3 P0_2/AN2 P0_1/AN1 P0_0/AN0 CVIN 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 50 49 48 47 46 45 44 43 42 P4_4 P4_5 P4_6 P4_7 P5_0 P5_1 P5_2 P5_3 P5_4 P5_5 P5_6 P5_7/CLKOUT P6_0/CTS0/RTS0 P6_1/CLK0 P6_2/RXD0/SCL0 P6_3/TXD0/SDA0 P6_4/CTS1/RTS1 P6_5/CLK1 P6_6/RXD1/SCL1 P6_7/TXD1/SDA1 P4_3 VCC2 VSS CE VCC VSS VDD2 VCCOFF VSS2 TEST1 LP3 LP4 AVSS M1 SYNCIN AVCC P97/ADTRG/SIN4 M306H7FGFP 41 40 39 38 37 36 35 34 33 32 31 BUSY SCLK RxD TxD VSS P9_5/ANEX0/CLK4 P8_3/INT1 P8_2/INT0 RESET XOUT P7_4/SDA3/TA2OUT P9_4/TB4IN/RMTIN P8_1/TA4IN P7_5/SCL3/TA2IN P9_6/ANEX1/SOUT4 P7_2/CLK2/TA1OUT P9_2/TB2IN/SOUT3 P8_6/XCOUT P8_0/TA4OUT P7_5/TA3OUT XIN RESET VSS VCC Note 1. Connect an oscillation circuit. Note 2. Figure is a use example for VCC1=VCC2. The mode setting method Signal line name Value CNVss Vcc M1 Vss RESET CE VssVcc Vcc Figure 17.13 Pin Connections for Serial I/O Mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 304 of 326 P7_1/RXD2/SCL2/TA0IN/TB5IN (Note 1) VSS VCC P7_0/TXD2/SDA2/TA0OUT (Note 1) (Note 1) P7_3/CTS2/RTS2/TA1IN P9_0/TB0IN/CLK3 P8_7/XCIN STARTB VCC1 P9_3/TB3IN/JSTIN P9_1/TB1IN/SIN3 P8_4/RMTOUT/INT2 P7_7/TA3IN CNVSS P8_5/NMI M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.9.2 Example of Circuit Application in the Standard Serial I/O Mode Figure 17.14 and 17.15 show example of circuit application in standard serial I/O mode 1 and mode 2, respectively. Refer to the user's manual for serial writer to handle pins controlled by a serial writer. Microcomputer SCLK input TxD input BUSY output RxD output P65/CLK1 P50(CE) P67/TxD1 P64/RTS1 P66/RxD1 CNVss M1 Reset input User reset signal RESET P85/NMI STARTB VCCOFF (1) Control pins and external circuitry will vary according to programmer. For more information, see the programmer manual. (2) In this example, modes are switched between single-chip mode and standard serial input/output mode by controlling the CNVss input with a switch. (3) If in standard serial input/output mode 1 there is a possibility that the user reset signal will go low during serial input/output mode, break the connection between the user reset signal and RESET pin by using, for example, a jumper switch. Figure 17.14 Circuit Application in Standard Serial I/O Mode 1 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 305 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION Microcomputer P65/CLK1 TxD output Monitor output RxD input P67/TxD1 P64/RST1 P66/RxD1 CNVss P50(CE) M1 P85/NMI STARTB VCCOFF (1) In this example, modes are switched between single-chip mode and standard serial input/output mode by controlling the CNVss input with a switch. Figure 17.15 Circuit Application in Standard Serial I/o Mode 2 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 306 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 17. FLASH MEMORY VERSION 17.10 Parallel I/O Mode In parallel input/output mode, the user ROM and boot ROM areas can be rewritten by using a parallel programmer suitable for M306H7FGFP. For more information about parallel programmers, contact the manufacturer of your parallel programmer. For details on how to use, refer to the user's manual included with your parallel programmer. 17.10.1 User ROM and Boot ROM Areas In the boot ROM area, an erase block operation is applied to only one 4 Kbyte block. The boot ROM area contains a standard serial input/output mode based rewrite control program which was written in it when shipped from the factory. Therefore, when using a serial programmer, be careful not to rewrite the boot ROM area. When in parallel output mode, the boot ROM area is located at addresses 0FF00016 to 0FFFFF16. When rewriting the boot ROM area, make sure that only this address range is rewritten. (Do not access other than the addresses 0FF00016 to 0FFFFF16.) 17.10.2 ROM Code Protect Function The ROM code protect function inhibits the flash memory from being read or rewritten. (Refer to the description of the functions to inhibit rewriting flash memory version.) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 307 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 18. PACKAGE OUTLINE 18. Package Outline JEITA Package Code P-QFP100-14x20-0.65 RENESAS Code PRQP0100JB-A Previous Code 100P6S-A MASS[Typ.] 1.6g HD *1 80 D 51 81 50 NOTE) 1. DIMENSIONS "*1" AND "*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION "*3" DOES NOT INCLUDE TRIM OFFSET. *2 HE E ZE Reference Symbol Dimension in Millimeters Min 19.8 13.8 Nom 20.0 14.0 2.8 22.5 16.5 22.8 16.8 23.1 17.1 3.05 0 0.25 0.13 0 0.1 0.3 0.15 0.2 0.4 0.2 10 0.65 0.8 0.10 0.575 0.825 0.4 0.6 0.8 Max 20.2 14.2 100 D 31 E A2 1 ZD Index mark 30 F c A2 HD HE A A1 A bp A1 L e y *3 bp Detail F c e y ZD ZE L 0.5 Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 308 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19. USEGE NOTES 19.1 Precautions for Power Control (1) When exiting stop mode by hardware reset, set RESET pin to "L" until a main clock or sub clock oscillation is stabilized. (2) Insert more than four NOP instructions after an WAIT instruction or a instruction to set the CM10 bit of CM1 register to "1". When shifting to wait mode or stop mode, an instruction queue reads ahead to the next instruction to halt a program by an WAIT instruction and an instruction to set the CM10 bit to "1" (all clocks stopped). The next instruction may be executed before entering wait mode or stop mode, depending on a combination of instruction and an execution timing. (3) Wait until the main clock oscillation stabilization time, before switching the clock source for CPU clock to the main clock. Similarly, wait until the sub clock oscillates stably before switching the clock source for CPU clock to the sub clock. (4) Suggestions to reduce power consumption * Ports The processor retains the state of each I/O port even when it goes to wait mode or to stop mode. A current flows in active I/O ports. A pass current flows in input ports that high-impedance state. When entering wait mode or stop mode, set non-used ports to input and stabilize the potential. * A/D converter When A/D conversion is not performed, set the VCUT bit of ADiCON1 register to "0" (no VREF connection). When A/D conversion is performed, start the A/D conversion at least 1 Es or longer after setting the VCUT bit to "1" (VREF connection). * Stopping peripheral functions Use the CM0 register CM02 bit to stop the unnecessary peripheral functions during wait mode. However, because the peripheral function clock (fC32) generated from the sub-clock does not stop, this measure is not conducive to reducing the power consumption of the chip. If low speed mode or low power dissipation mode is to be changed to wait mode, set the CM02 bit to "0" (do not peripheral function clock stopped when in wait mode), before changing wait mode. * Switching the oscillation-driving capacity Set the driving capacity to "LOW" when oscillation is stable. * External clock When using an external clock input for the CPU clock, set the CM0 register CM05 bit to "1" (stop). Setting the CM05 bit to "1" disables the XOUT pin from functioning, which helps to reduce the amount of current drawn in the chip. (When using an external clock input, note that the clock remains fed into the chip regardless of how the CM05 bit is set.) 19.2 Precautions for Protect Set the PRC2 bit to "1" (write enabled) and then write to any address, and the PRC2 bit will be cleared to "0" (write protected). The registers protected by the PRC2 bit should be changed in the next instruction after setting the PRC2 bit to "1". Make sure no interrupts or DMA transfers will occur between the instruction in which the PRC2 bit is set to "1" and the next instruction. 19.3 19.3.1 Precautions for Interrupts Reading address 0000016 Do not read the address 0000016 in a program. When a maskable interrupt request is accepted, the CPU reads interrupt information (interrupt number and interrupt request priority level) from the address 0000016 during the interrupt sequence. At this time, the IR bit for the accepted interrupt is cleared to "0". If the address 0000016 is read in a program, the IR bit for the interrupt which has the highest priority among the enabled interrupts is cleared to "0". This causes a problem that the interrupt is canceled, or an unexpected interrupt request is generated. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 309 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.3.2 Setting the SP Set any value in the SP (USP, ISP) before accepting an interrupt. The SP (USP, ISP) is cleared to `000016' after reset. Therefore, if an interrupt is accepted before setting any value in the SP (USP, ISP), the program may go out of control. Especially when using NMI interrupt, set a value in the ISP at the beginning of the program. For the first and only the first instruction after reset, all interrupts including NMI interrupt are disabled. 19.3.3 The NMI Interrupt (1) The NMI interrupt cannot be disabled. If this interrupt is unused, connect the NMI pin to VCC via a resistor (pull-up). (2) The input level of the NMI pin can be read by accessing the P8 register's P8_5 bit. Note that the P8_5 bit can only be read when determining the pin level in NMI interrupt routine. (3) Stop mode cannot be entered into while input on the NMI pin is low. This is because while input on the NMI pin is low the CM1 register's CM10 bit is fixed to "0". (4) Do not go to wait mode while input on the NMI pin is low. This is because when input on the NMI pin goes low, the CPU stops but CPU clock remains active; therefore, the current consumption in the chip does not drop. In this case, normal condition is restored by an interrupt generated thereafter. (5) The low and high level durations of the input signal to the NMI pin must each be 2 CPU clock cycles + 300 ns or more. 19.3.4 Changing the Interrupt Generate Factor If the interrupt generate factor is changed, the IR bit in the interrupt control register for the changed interrupt may inadvertently be set to "1" (interrupt requested). If you changed the interrupt generate factor for an interrupt that needs to be used, be sure to clear the IR bit for that interrupt to "0" (interrupt not requested). "Changing the interrupt generate factor" referred to here means any act of changing the source, polarity or timing of the interrupt assigned to each software interrupt number. Therefore, if a mode change of any peripheral function involves changing the generate factor, polarity or timing of an interrupt, be sure to clear the IR bit for that interrupt to "0" (interrupt not requested) after making such changes. Refer to the description of each peripheral function for details about the interrupts from peripheral functions. Figure 19.1 shows the procedure for changing the interrupt generate factor. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 310 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES Changing the interrupt source Disable interrupts (Note 2, Note 3) Change the interrupt generate factor (including a mode change of peripheral function) Use the MOV instruction to clear the IR bit to "0" (interrupt not requested) (Note 3) Enable interrupts (Note 2, Note 3) End of change IR bit: A bit in the interrupt control register for the interrupt whose interrupt generate factor is to be changed Note 1: The above settings must be executed individually. Do not execute two or more settings simultaneously (using one instruction). Note 2: Use the I flag for the INTi interrupt (i = 0 to 5). For the interrupts from peripheral functions other than the INTi interrupt, turn off the peripheral function that is the source of the interrupt in order not to generate an interrupt request before changing the interrupt generate factor. In this case, if the maskable interrupts can all be disabled without causing a problem, use the I flag. Otherwise, use the corresponding ILVL2 to ILVL0 bit for the interrupt whose interrupt generate factor is to be changed. Note 3: Refer to Section "Rewrite the Interrupt Control Register" for details about the instructions to use and the notes to be taken for instruction execution. Figure 19.1 Procedure for Changing the Interrupt Generate Factor 19.3.5 INT Interrupt (1) Either an "L" level of at least tW(INL) or an "H" level of at least tW(INH) width is necessary for the signal input to pins INT0 through INT5 regardless of the CPU operation clock. (2) If the POL bit in the INT0IC to INT5IC registers or the IFSR7 to IFSR0 bits in the IFSR register are changed, the IR bit may inadvertently set to 1 (interrupt requested). Be sure to clear the IR bit to 0 (interrupt not requested) after changing any of those register bits. 19.3.6 Rewrite the Interrupt Control Register (1) The interrupt control register for any interrupt should be modified in places where no requests for that interrupt may occur. Otherwise, disable the interrupt before rewriting the interrupt control register. (2) To rewrite the interrupt control register for any interrupt after disabling that interrupt, be careful with the instruction to be used. * Changing any bit other than the IR bit If while executing an instruction, a request for an interrupt controlled by the register being modified occurs, the IR bit in the register may not be set to "1" (interrupt requested), with the result that the interrupt request is ignored. If such a situation presents a problem, use the instructions shown below to modify the register. Usable instructions: AND, OR, BCLR, BSET Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 311 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES * Changing the IR bit Depending on the instruction used, the IR bit may not always be cleared to "0" (interrupt not requested). Therefore, be sure to use the MOV instruction to clear the IR bit. (3) When using the I flag to disable an interrupt, refer to the sample program fragments shown below as you set the I flag. (Refer to (2) for details about rewrite the interrupt control registers in the sample program fragments.) Examples 1 through 3 show how to prevent the I flag from being set to "1" (interrupts enabled) before the interrupt control register is rewrited, owing to the effects of the internal bus and the instruction queue buffer. Example 1: Using the NOP instruction to keep the program waiting until the interrupt control register is modified INT_SWITCH1: FCLR I AND.B #00h, 0055h NOP ; NOP FSET I ; Disable interrupts. ; Set the TA0IC register to "0016". ; Enable interrupts. The number of NOP instruction is as follows. PM20=1(1 wait) : 2, PM20=0(2 wait) : 3, when using HOLD function : 4. Example 2: Using the dummy read to keep the FSET instruction waiting INT_SWITCH2: FCLR I AND.B #00h, 0055h MOV.W MEM, R0 FSET I ; Disable interrupts. ; Set the TA0IC register to "0016". ; Dummy read. ; Enable interrupts. Example3: Using the POPC instruction to changing the I flag INT_SWITCH3: PUSHC FLG FCLR I AND.B #00h, 0055h POPC FLG ; Disable interrupts. ; Set the TA0IC register to "0016". ; Enable interrupts. * Watchdog Timer Interrupt Initialize the watchdog timer after the watchdog timer interrupt occurs. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 312 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.4 19.4.1 Precautions for DMAC Write to DMAE Bit in DMiCON Register When both of the conditions below are met, follow the steps below. Conditions * The DMAE bit is set to "1" again while it remains set (DMAi is in an active state). * A DMA request may occur simultaneously when the DMAE bit is being written. Step 1: Write "1" to the DMAE bit and DMAS bit in DMiCON register simultaneously (*1). Step 2: Make sure that the DMAi is in an initial state (*2) in a program. If the DMAi is not in an initial state, the above steps should be repeated. Notes *1 The DMAS bit remains unchanged even if "1" is written. However, if "0" is written to this bit, it is set to "0" (DMA not requested). In order to prevent the DMAS bit from being modified to "0", "1" should be written to the DMAS bit when "1" is written to the DMAE bit. In this way the state of the DMAS bit immediately before being written can be maintained. Similarly, when writing to the DMAE bit with a read-modify-write instruction, "1" should be written to the DMAS bit in order to maintain a DMA request which is generated during execution. *2 Read the TCRi register to verify whether the DMAi is in an initial state. If the read value is equal to a value which was written to the TCRi register before DMA transfer start, the DMAi is in an initial state. (If a DMA request occurs after writing to the DMAE bit, the value written to the TCRi register 1.) If the read value is a value in the middle of transfer, the DMAi is not in an initial state. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 313 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.5 Precautions for Timers Precautions for Timer A 19.5.1 Timer A (1) Timer A (Timer Mode) The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) register and the TAi register before setting the TAiS bit in the TABSR register to "1" (count starts). Always make sure the TAiMR register is modified while the TAiS bit remains "0" (count stops) regardless whether after reset or not. (2) While counting is in progress, the counter value can be read out at any time by reading the TAi register. However, if the counter is read at the same time it is reloaded, the value "FFFF16" is read. Also, if the counter is read before it starts counting after a value is set in the TAi register while not counting, the set value is read. 19.5.2 Timer A (Event Counter Mode) (1) The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) register, the TAi register, the UDF register, the ONSF register TAZIE, TA0TGL and TA0TGH bits and the TRGSR register before setting the TAiS bit in the TABSR register to "1" (count starts). Always make sure the TAiMR register, the UDF register, the ONSF register TAZIE, TA0TGL and TA0TGH bits and the TRGSR register are modified while the TAiS bit remains "0" (count stops) regardless whether after reset or not. (2) While counting is in progress, the counter value can be read out at any time by reading the TAi register. However, "FFFF16" can be read in underflow, while reloading, and "000016" in overflow. When setting TAi register to a value during a counter stop, the setting value can be read before a counter starts counting. 19.5.3 Timer A (One-shot Timer Mode) (1) The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) register, the TAi register, the ONSF register TA0TGL and TA0TGH bits and the TRGSR register before setting the TAiS bit in the TABSR register to "1" (count starts). Always make sure the TAiMR register, the ONSF register TA0TGL and TA0TGH bits and the TRGSR register are modified while the TAiS bit remains "0" (count stops) regardless whether after reset or not. (2) When setting TAiS bit to "0" (count stop), the followings occur: *A counter stops counting and a content of reload register is reloaded. *TAiOUT pin outputs "L". *After one cycle of the CPU clock, the IR bit of TAiIC register is set to "1" (interrupt request). (3) Output in one-shot timer mode synchronizes with a count source internally generated. When an external trigger has been selected, one-cycle delay of a count source as maximum occurs between a trigger input to TAiIN pin and output in one-shot timer mode. (4) The IR bit is set to "1" when timer operation mode is set with any of the following procedures: *Select one-shot timer mode after reset. *Change an operation mode from timer mode to one-shot timer mode. *Change an operation mode from event counter mode to one-shot timer mode. To use the timer Ai interrupt (the IR bit), set the IR bit to "0" after the changes listed above have been made. (5) When a trigger occurs, while counting, a counter reloads the reload register to continue counting after generating a re-trigger and counting down once. To generate a trigger while counting, generate a second trigger between occurring the previous trigger and operating longer than one cycle of a timer count source. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 314 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.5.4 Timer A (Pulse Width Modulation Mode) (1) The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR (i = 0 to 4) register, the TAi register, the ONSF register TA0TGL and TA0TGH bits and the TRGSR register before setting the TAiS bit in the TABSR register to "1" (count starts). Always make sure the TAiMR register, the ONSF register TA0TGL and TA0TGH bits and the TRGSR register are modified while the TAiS bit remains "0" (count stops) regardless whether after reset or not. (2) The IR bit is set to "1" when setting a timer operation mode with any of the following procedures: *Select the PWM mode after reset. *Change an operation mode from timer mode to PWM mode. *Change an operation mode from event counter mode to PWM mode. To use the timer Ai interrupt (interrupt request bit), set the IR bit to "0" by program after the above listed changes have been made. (3) When setting TAiS register to "0" (count stop) during PWM pulse output, the following action occurs: *Stop counting. *When TAiOUT pin is output "H", output level is set to "L" and the IR bit is set to "1". *When TAiOUT pin is output "L", both output level and the IR bit remains unchanged. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 315 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES Precautions for Timer B 19.5.5 Timer B (Timer Mode) (1) The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TBiMR (i = 0 to 5) register and TBi register before setting the TBiS bit in the TABSR or the TBSR register to "1" (count starts). Always make sure the TBiMR register is modified while the TBiS bit remains "0" (count stops) regardless whether after reset or not. (2) A value of a counter, while counting, can be read in TBi register at any time. "FFFF16" is read while reloading. Setting value is read between setting values in TBi register at count stop and starting a counter. 19.5.6 Timer B (Event Counter Mode) (1) The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TBiMR (i = 0 to 5) register and TBi register before setting the TBiS bit in the TABSR or the TBSR register to "1" (count starts). Always make sure the TBiMR register is modified while the TBiS bit remains "0" (count stops) regardless whether after reset or not. (2) The counter value can be read out on-the-fly at any time by reading the TBi register. However, if this register is read at the same time the counter is reloaded, the read value is always "FFFF16." If the TBi register is read after setting a value in it while not counting but before the counter starts counting, the read value is the one that has been set in the register. 19.5.7 Timer B (Pulse Period/pulse Width Measurement Mode) (1) The timer remains idle after reset. Set the mode, count source, etc. using the TBiMR (i = 0 to 5) register before setting the TBiS bit in the TABSR or the TBSR register to "1" (count starts). Always make sure the TBiMR register is modified while the TBiS bit remains "0" (count stops) regardless whether after reset or not. To clear the MR3 bit to "0" by writing to the TBiMR register while the TBiS bit = "1" (count starts), be sure to write the same value as previously written to the TM0D0, TM0D1, MR0, MR1, TCK0 and TCK1 bits and a 0 to the MR2 bit. (2) The IR bit of TBiIC register (i=0 to 5) goes to "1" (interrupt request), when an effective edge of a measurement pulse is input or timer Bi is overflowed. The factor of interrupt request can be determined by use of the MR3 bit of TBiMR register within the interrupt routine. (3) If the source of interrupt cannot be identified by the MR3 bit such as when the measurement pulse input and a timer overflow occur at the same time, use another timer to count the number of times timer B has overflowed. (4) To set the MR3 bit to "0" (no overflow), set TBiMR register with setting the TBiS bit to "1" and counting the next count source after setting the MR3 bit to "1" (overflow). (5) Use the IR bit of TBiIC register to detect only overflows. Use the MR3 bit only to determine the interrupt factor within the interrupt routine. (6) When a count is started and the first effective edge is input, an indeterminate value is transferred to the reload register. At this time, timer Bi interrupt request is not generated. (7) A value of the counter is indeterminate at the beginning of a count. MR3 may be set to "1" and timer Bi interrupt request may be generated between a count start and an effective edge input. (8) For pulse width measurement, pulse widths are successively measured. Use program to check whether the measurement result is an "H" level width or an "L" level width. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 316 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.6 19.6.1 Precautions for Serial I/O (Clock-synchronous Serial I/O) Transmission/reception With an external clock selected, and choosing the RTS function, the output level of the RTSi pin goes to "L" when the data-receivable status becomes ready, which informs the transmission side that the reception has become ready. The output level of the RTSi pin goes to "H" when reception starts. So if the RTSi pin is connected to the CTSi pin on the transmission side, the circuit can transmission and reception data with consistent timing. With the internal clock, the RTS function has no effect. 19.6.2 Transmission When an external clock is selected, the conditions must be met while if the UiC0 register's CKPOL bit = "0" (transmit data output at the falling edge and the receive data taken in at the rising edge of the transfer clock), the external clock is in the high state; if the UiC0 register's CKPOL bit = "1" (transmit data output at the rising edge and the receive data taken in at the falling edge of the transfer clock), the external clock is in the low state. * The TE bit of UiC1 register= "1" (transmission enabled) * The TI bit of UiC1 register = "0" (data present in UiTB register) * If CTS function is selected, input on the CTSi pin = "L" 19.6.3 Reception (1) In operating the clock-synchronous serial I/O, operating a transmitter generates a shift clock. Fix settings for transmission even when using the device only for reception. Dummy data is output to the outside from the TxDi pin when receiving data. (2) When an internal clock is selected, set the UiC1 register (i = 0 to 2)'s TE bit to 1 (transmission enabled) and write dummy data to the UiTB register, and the shift clock will thereby be generated. When an external clock is selected, set the UiC1 register (i = 0 to 2)'s TE bit to 1 and write dummy data to the UiTB register, and the shift clock will be generated when the external clock is fed to the CLKi input pin. (3) When successively receiving data, if all bits of the next receive data are prepared in the UARTi receive register while the UiC1 register (i = 0 to 2)'s RE bit = "1" (data present in the UiRB register), an overrun error occurs and the UiRB register OER bit is set to "1" (overrun error occurred). In this case, because the content of the UiRB register is indeterminate, a corrective measure must be taken by programs on the transmit and receive sides so that the valid data before the overrun error occurred will be retransmitted. Note that when an overrun error occurred, the SiRIC register IR bit does not change state. (4) To receive data in succession, set dummy data in the lower-order byte of the UiTB register every time reception is made. (5) When an external clock is selected, the conditions must be met while if the CKPOL bit = "0", the external clock is in the high state; if the CKPOL bit = "1", the external clock is in the low state. *. The RE bit of UiC1 register= "1" (reception enabled) *. The TE bit of UiC1 register= "1" (transmission enabled) *. The TI bit of UiC1 register= "0" (data present in the UiTB register) Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 317 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.7 19.7.1 Precautions for Serial I/O (UART Mode) Special Mode 4 (SIM Mode) A transmit interrupt request is generated by setting the U2C1 register U2IRS bit to "1" (transmission complete) and U2ERE bit to "1" (error signal output) after reset. Therefore, when using SIM mode, be sure to clear the IR bit to "0" (no interrupt request) after setting these bits. 19.8 Precautions for A/D Converter (1) Set ADCON0 (except bit 6), ADCON1 and ADCON2 registers when A/D conversion is stopped (before a trigger occurs). (2) When the VCUT bit of ADCON1 register is changed from "0" (Vref not connected) to "1" (Vref connected), start A/D conversion after passing 1 s or longer. (3) To prevent noise-induced device malfunction or latchup, as well as to reduce conversion errors, insert capacitors between the AVCC and analog input pins (ANi (i=0 to 7)) each and the AVSS pin. Similarly, insert a capacitor between the VCC pin and the VSS pin. Figure 19.2 is an example connection of each pin. (4) Make sure the port direction bits for those pins that are used as analog inputs are set to "0" (input mode). Also, if the ADCON0 register's TGR bit = 1 (external trigger), make sure the port direction bit for the ADTRG pin is set to "0" (input mode). (5) The AD frequency must be 10 MHz or less. Without sample-and-hold function, limit the AD frequency to 250kHZ or more. With the sample and hold function, limit the AD frequency to 1MHZ or more. (6) When changing an A/D operation mode, select analog input pin again in the CH2 to CH0 bits of ADCON0 register and the SCAN1 to SCAN0 bits of ADCON1 register. (7) If the CPU reads the ADi register (i = 0 to 7) at the same time the conversion result is stored in the ADi register after completion of A/D conversion, an incorrect value may be stored in the ADi register. This problem occurs when a divide-by-n clock derived from the main clock or a subclock is selected for CPU clock. * When operating in one-shot or single-sweep mode Check to see that A/D conversion is completed before reading the target ADi register. (Check the ADIC register's IR bit to see if A/D conversion is completed.) * When operating in repeat mode or repeat sweep mode 0 or 1 Use the main clock for CPU clock directly without dividing it. (8) If A/D conversion is forcibly terminated while in progress by setting the ADCON0 register's ADST bit to "0" (A/D conversion halted), the conversion result of the A/D converter is indeterminate. The contents of ADi registers irrelevant to A/D conversion may also become indeterminate. If while A/D conversion is underway the ADST bit is cleared to "0" in a program, ignore the values of all ADi registers. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 318 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES Microcomputer VCC1 VCC1 (16pin) AVCC C4 VSS C2 VCC2 VCC2 (62pin) C5 VSS ANi AVSS C3 VCC2 ANi: ANi (i=0 to 7) Note 1: C10.47F, C20.47F, C3100pF, C40.1F, C50.1F (reference) Note 2: Use thick and shortest possible wiring to connect capacitors. Figure 19.2 Use of capacitors to reduce noise Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 319 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.9 Precautions for Programmable I/O Ports (1) Setting the SM32 bit in the S3C register to "1" causes the P92 pin to go to a high-impedance state. Similarly, setting the SM42 bit in the S4C register to "1" causes the P96 pin to go to a high-impedance state. (2) The input threshold voltage of pins differs between programmable input/output ports and peripheral functions. Therefore, if any pin is shared by a programmable input/output port and a peripheral function and the input level at this pin is outside the range of recommended operating conditions VIH and VIL (neither "high" nor "low"), the input level may be determined differently depending on which side-the programmable input/ output port or the peripheral function-is currently selected. 19.10 Electric Characteristic Differences Between Mask ROM and Flash Memory Version Microcomputers Flash memory version and mask ROM version may have different characteristics, operating margin, noise tolerated dose, noise width dose in electrical characteristics due to internal ROM, different layout pattern, etc. When switching to the mask ROM version, conduct equivalent tests as system evaluation tests conducted in the flush memory version. 19.11 Precautions for Flash Memory Version 19.11.1 Precautions for Functions to Inhibit Rewriting Flash Memory Rewrite ID codes are stored in addresses 0FFFDF16, 0FFFE316, 0FFFEB16, 0FFFEF16, 0FFFF316, 0FFFF716, and 0FFFFB16. If wrong data are written to theses addresses, the flash memory cannot be read or written in standard serial I/O mode. The ROMCP register is mapped in address 0FFFFF16. If wrong data is written to this address, the flash memory cannot be read or written in parallel I/O mode. In the flash memory version of microcomputer, these addresses are allocated to the vector addresses (H) of fixed vectors. 19.11.2 Precautions for Stop mode When shifting to stop mode, the following settings are required: * Set the FMR01 bit to "0" (CPU rewrite mode disabled) and disable DMA transfers before setting the CM10 bit to "1" (stop mode). * Execute the JMP.B instruction subsequent to the instruction which sets the CM10 bit to "1" (stop mode) Example program BSET 0, CM 1 ; Stop mode JMP.B L1 L1: Program after returning from stop mode Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 320 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.11.3 Precautions for Wait mode When shifting to wait mode, set the FMR01 bit to "0" (CPU rewrite mode diabled) before executing the WAIT instruction. 19.11.4 Precautions for Low power dissipation mode If the CM05 bit is set to "1" (main clock stop), the following commands must not be executed. * Program * Block erase * Lock bit program 19.11.5 Writing command and data Write the command code and data at even addresses. 19.11.6 Precautions for Program Command Write `xx4016' in the first bus cycle and write data to the write address in the second bus cycle, and an auto program operation (data program and verify) will start. Make sure the address value specified in the first bus cycle is the same even address as the write address specified in the second bus cycle. 19.11.7 Precautions for Lock Bit Program Command Write `xx7716' in the first bus cycle and write `xxD016' to the uppermost address of a block (even address, however) in the second bus cycle, and the lock bit for the specified block is cleared to "0". Make sure the address value specified in the first bus cycle is the same uppermost block address that is specified in the second bus cycle. 19.11.8 Operation speed Before entering CPU rewrite mode (EW0 or EW1 mode), select 10 MHz or less for CPU clock using the CM0 register's CM06 bit and CM1 register's CM17-6 bits. Also, set the PM1 register's PM17 bit to 1 (with wait state). 19.11.9 Instructions inhibited against use The following instructions cannot be used in EW0 mode because the flash memory's internal data is referenced: UND instruction, INTO instruction, JMPS instruction, JSRS instruction, and BRK instruction 19.11.10 Interrupts EW0 Mode * Any interrupt which has a vector in the variable vector table can be used providing that its vector is transferred into the RAM area. * The NMI and watchdog timer interrupts can be used because the FMR0 register and FMR1 register are initialized when one of those interrupts occurs. The jump addresses for those interrupt service routines should be set in the fixed vector table. Because the rewrite operation is halted when a NMI or watchdog timer interrupt occurs, the rewrite program must be executed again after exiting the interrupt service routine. * The address match interrupt cannot be used because the flash memory's internal data is referenced. EW1 Mode * Make sure that any interrupt which has a vector in the variable vector table or address match interrupt will not be accepted during the auto program or auto erase period. * Avoid using watchdog timer interrupts. * The NMI interrupt can be used because the FMR0 register and FMR1 register are initialized when this interrupt occurs. The jump address for the interrupt service routine should be set in the fixed vector table. Because the rewrite operation is halted when a NMI interrupt occurs, the rewrite program must be executed again after exiting the interrupt service routine. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 321 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.11.11 How to access To set the FMR01, FMR02, or FMR11 bit to "1", write "0" and then "1" in succession. This is necessary to ensure that no interrupts or DMA transfers will occur before writing "1" after writing "0". Also only when NMI pin is "H" level. 19.11.12 Writing in the user ROM area EW0 Mode * If the power supply voltage drops while rewriting any block in which the rewrite control program is stored, a problem may occur that the rewrite control program is not correctly rewritten and, consequently, the flash memory becomes unable to be rewritten thereafter. In this case, standard serial I/O or parallel I/O mode should be used. EW1 Mode * Avoid rewriting any block in which the rewrite control program is stored. 19.11.13 DMA transfer In EW1 mode, make sure that no DMA transfers will occur while the FMR0 register's FMR00 bit = 0 (during the auto program or auto erase period). 19.11.14 Regarding Programming/Erasure Times and Execution Time As the number of programming/erasure times increases, so does the execution time for software commands (Program, Block Erase, and Lock Bit Program). Especially when the number of programming/erasure times exceeds 100, the software command execution time is noticeably extended. Therefore, the software command wait time that is set must be greater than the maximum rated value of electrical characteristics. The software commands are aborted by hardware reset 1, NMI interrupt, and watchdog timer interrupt. If a software command is aborted by such reset or interrupt, the block that was in process must be erased before reexecuting the aborted command. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 322 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.12 Other Notes 19.12.1 When the power is being turned on or off Start VCC1, VCC2, VDD2 and AVCC simultaneously. While this device is operating, set these pins to the same electric potential. Also, turn off VCC1, VCC2, VDD2 and AVCC simultaneously when the power supply is being turned off. When using VCC1 < VCC2, ensure voltage of VCC1 will not exceed voltage of VCC2 while the power is being turned on or off. Execute in the following procedure when VCC1 is turned off (VCC2 voltage is supplied). 19.12.2 Procedure of VCC1 OFF(Note 1) (1) Disable an interrupt which uses pins related to VCC1. (2) Stop peripheral functions related to VCC1 (Note 2). (3) Set pins related to VCC1 to input mode. (4) VCCOFF pin is switched from "L" to "H" . (5) Turn off VCC1. 19.12.3 Procedure of VCC1 ON (1) Turn on VCC1. (2) VCCOFF pin (91-pin) is switched from "H" to "L" . (3) Set pins VCC1, Peripheral function and Interrupt. Note 1: Refer to the following "Additions" for details of procedures (1) to (4). Note 2: Only when the input from pins related to VCC1 is used. Refer to the following "Additions" for details. (1) Disable an affected interrupt by pins related to VCC1. Disable an affected interrupt by pins related to VCC1 by setting the interrupt priority level selection and the interrupt request bits in the the following interrupt control register to "0". In the transitional state when changing the power supply voltage including being turned on or off, ensure each voltage of VCC1, VDD2, and VDD3 will not exceed voltage of VCC2. TA0IC to TA4IC (timer A interrupt control register) INT0 to INT2IC (external interrupt control register) S0RIC to S2RIC (UART receive interrupt control register) Even if other interrupts are disabled without any problem in software, clear the I flag and it is also possible to execute the above interrupt disable process after the procedure (4). (2) Stop peripheral functions related to VCC1 Stop the function when pins related to VCC1 input affect. When pins related to VCC1 input affect as follows: *When operating in timer A (TA0 to TA4) and the event count mode *When the gate input function is used in the event count mode, the one-shot timer, and PWM mode. (When the MR2 bit in the timer A mode registers TA0MR to TA4MR are set to "1") *When UART to UART2 reception are set Set the following in these cases. *Timer A Set the timer count start flags of timers A0 to A4 (TA0S to TA4S bits in the TABSR register) to "0". *UART reception Set the RE and TE bits in the U0C1 to U2C1 registers to "0". Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 323 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.12.4 Precautions when sub clock starts When a signal "H" is applied to the STARTB pin and a reset is deserted, a sub clock divided-by-8 becomes a CPU clock. When using in this condition, set the CM07 bit in the CM0 register to "1" and switch the CPU clock to sub clock (no division). 19.12.5 Power supply noise and latch-up In order to avoid power supply noise and latch-up, connect a bypass capacitor (more than 0.1F) directly between the VCC pin and VSS pin, VDD2 pin and VSS2 pin, AVCC pin and AVSS pin using a heavy wire. And, connect VSS (GND) to the TEST1 pin (93 pin) via the capacitor (more than 0.1F). 19.12.6 When oscillation circuit stop for data slicer Expansion register XTAL_VCO, PDC_VCO_ON,VPS_VCO_ON is set at "L", when the data slicer is not used, and the oscillation is stopped. When starting oscillation again, set data at the folowing order. (a) Set expansion register XTAL_VCO = "H." (b) Set expansion register PDC_VCO_ON, VPS_VCO_ON = "H." (c) 60 ms or more is a waiting state (stability period of internal oscillation circuit + data slice prepara tion). * To operate slice RAM, set expansion register XTAL_VCO = "H." Access the memories after wating for 20 ms certainly when resuming synchronous oscillation from the off state. 19.12.7 When operation start from stand-by mode (clock is stopped) Set up an extended register as follows in standby mode. (a) Set extended register XTAL_VCO, PDC_VCO_ON, and VPS_VCO_ON as "L." When you return to an oscillation state from a clock oscillation stop, set up as the notes of the oscillation circuit stop for data slicers. 19.12.8 Notes concerning address 3616 expansion registers and address 3E16 data setting Please do not change data after setting initial data to the corresponding addresses 3616 and 3E16 interrupt control bits when you use the interrupt of the expansion feature (SLICEON, remote control, HINT, clock timer, and remote control transmission interrupt). Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 324 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.12.9 Notes on operating with a low supply voltage (VCC = 2.0 V to 5.5 V, f(XCIN) = 32 kHz) When in single-chip mode, this product can operate with a low supply voltage only during low power dissipation mode. Before operating with a low supply voltage, always be sure to set the relevant register bits to select low power dissipation mode (BCLK : f(XCIN), main clock XIN : stop, subclock XCIN : oscillating). Then reduce the power supply voltage VCC to 3.0 V. Also, when returning to normal operation, raise the power supply voltage to 5.0V while in low power consumption mode before entering normal operation mode. When moving from any operation mode to another, make sure a state transition occurs according to the state transition diagram (Figure 4.9) in Section 4.4, "Power control." The status of the power supply voltage VCC during operation mode transition is shown in Figure 19.3 below. 5V VCC 3V Power control operation modes Normal operation mode Low power dissipation mode Normal operation mode Note 1: Normal operation mode refers to the high-speed, medium-speed, and low-speed modes. Note 2: When operating with a low supply voltage (2.6 V or more), be aware that only the CPU, ROM, RAM, input/output ports, timers (timers A and B), clock timer, and the interrupt control circuit can be used. All other internal resources (e.g., data slicer, DMAC and A/D ) cannot be used. Note 3: When operating with a low supply voltage (less than 2.6 V), be aware that only the CPU, RAM, Input/Output ports, clock timer, and interrupt control circuit can be used. Figure 19.3 Status of the power supply voltage VCC during operation mode transition 19.13 Serial I/O (RxDi input setup time) For the RXDi input setup time, refer to the rated values shown below, as well as Electrical Characteristics Table 16.23, "Serial I/O." Table 19.1 Symbol tsu(D-C) RxDi input setup time Serial I/O (VCC=5V) Parameter Standard Min. Max. 70 Unit ns Note: Refer to "Table 16.23. Serial I/O of the Electrical Characteristics. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 325 of 326 M306H7MG-XXXFP/MC-XXXFP/FGFP 19. USAGE NOTES 19.14 Precautions for LP3 and LP4 pins Cannect capacitors to LP3 and LP4 as shown in Figure 19.4. LP4 2.0K 0.1F 47pF LP3 M306H7MG-XXXFP/ MC-XXXFP/FGFP 2.0K 0.1F 47pF Figure 19.4 Use of capacitors to reduce noise Notes on pins CVIN, SYNCIN, and SVREF Please connect pins CVIN, SYNCIN, and SVREF with GND when you do not use the data slicer. Rev.2.10 Oct 25, 2006 REJ03B0152-0210 Page 326 of 326 REVISION HISTORY Rev. 1.00 1.01 1.02 2.00 Date Sep 02, 2005 Sep 15, 2005 Oct 27, 2005 Mar 31, 2006 M306H7MG-XXXFP/MC-XXXFP/FGFP Datasheet Description Page 323 9 162 162 211 212 215 216 217 218 220 223 225 226 227 First Edition issued Summary DESCRIPTION Table 1.5 Pin Description (3) The polarity of STARTB was opposite --> it corrected. I2C0 Interrupt Control Register and Reserved Register are added. Reserved Register is changed. Figure of 13. Address 0C16, 1316, 1A16 is changed. Figure of 15. Address 1C16 is changed. Figure of 21. Address 2216 is changed. Figure of 22. Address 2316 is changed. Figure of 23. Address 2416 is changed. Figure of 25. Address 2616 is changed. Figure of 27. Address 2816 is changed. Figure of 32. Address 2D16 is changed. Figure of 35. Address 3016 is changed. Figure of 36. Address 3116 is changed. Figure of 39. Address 3416 is changed. Figure of 40. Address 3516 is changed. 232 to Figure of 47. Assress 3C16 to 50. Assress 3F16 are changed. 234 241 F.14.14 is changed. 244 to 14.6 (6) Remote control transmission function is added. 246 277 281 285 300 301 2.10 Oct 25, 2006 19 23 36 38 47 53 56 57 64 65 143 162 166 Notes of T.17.2 are changed. Note 2 of T.17.3 is changed. Note 5 of T.17.5 is changed. T.17.7 is changed. F.17.13 is changed. Table of register address is changed. F.3.4 is changed. T.4.2 is changed. T.4.4 is changed. T.6.2 is changed. F.6.6 is changed. F.6.9 is changed. L9 to L10 are added. Notes of F.8.2 is changed. Notes of F.8.3 is changed. T.11.1 is changed. Figure of I2C0 Interrupt Control Register is changed. Notes of F.12.3 is changed. A-1 REVISION HISTORY Rev. 2.10 Date Oct 25, 2006 M306H7MG-XXXFP/MC-XXXFP/FGFP Datasheet Description Page 182 200 211 218 226 228 233 253 260 262 267 293 303 304 305 306 324 F.14.1 is changed. T.14.4 is changed. Summary Figure of 13. Address 0C16, 1316, 1A16, is changed. Figure of 25. Address 2616 is changed. Figure of 38. Address 3316 is changed. Figure of 41. Address 3616 is changed. Figure of 49. Address 3E16 is changed. F.15.1 is changed. F.15.9 is changed. Note of F.15.11 is delated. T.16.8 is changed. T.17.4 is changed. T.17.7 is changed. F.17.13 is changed. F.17.14 is changed. F.17.15 is changed. 19.12.8 Notes concerning address 3616 expansion registers and address 3E16 is added. A-2 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 http://www.renesas.com Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 (c) 2006. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .7.0 |
Price & Availability of M306H7FGFP
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |