|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
HIGH CURRENT POWER INDUCTORS 1. PART NO. EXPRESSION : SSL0605 SERIES SSL0605-R10YF (a) (b) (c) (d)(e) (a) Series code (b) Dimension code (c) Inductance code : R10 = 0.10uH (d) Tolerance code : Y = 30% (e) F : Lead Free 2. CONFIGURATION & DIMENSIONS : A D R10 B E L G C PCB Pattern Unit:m/m A 7.2 Max. B 6.8 Max. C 5.0 Max. D 1.50.5 E 2.50.5 G 2.5 Max. H 4.5 Max. L 7.5 Max. 3. SCHEMATIC : 4. GENERAL SPECIFICATION : a) Operating temp. : -55C to +125C b) Storage temp. : -55C to +125C c) Irms (A) : Will cause coil temp. to rise approximately T=40C without core loss. d) Isat (A) : Will cause L0 to drop approximately 20% e) Part temperature (ambient + temp. rise) : Should not exceed 125C under worst case operating conditions. 5. ELECTRICAL CHARACTERISTICS : Part No. SSL0605-R10YF SSL0605-R15YF SSL0605-R20YF Inductance L0 ( uH ) 0.10 30% 0.15 30% 0.20 30% Test Freq. ( Hz ) 0.25V/1M 0.25V/1M 0.25V/1M DCR (m ) Max. 0.50 0.50 0.50 Irms (A) Max. 30 24 19 Isat (A) Max. 37 30 24 NOTE : Specifications subject to change without notice. Please check our website for latest information. H 05.05.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 1 HIGH CURRENT POWER INDUCTORS 6. CHARACTERISTICS CURVES : SSL0605-R10YF SSL0605 SERIES SSL0605-R15YF SSL0605-R20YF NOTE : Specifications subject to change without notice. Please check our website for latest information. 05.05.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 2 HIGH CURRENT POWER INDUCTORS 7. RELIABILITY AND TEST CONDITION : SSL0605 SERIES ITEM Electrical Characteristics Test Inductance DCR Heat Rated Current (Irms) PERFORMANCE Refer to standard electrical characteristics list TEST CONDITION HP4284A, CH11025, CH3302, CH1320, CH1320S LCR meter. CH16502, Agilent33420A Micro-Ohm Meter. Irms(A) will cause the coil temperature rise approximately T=40C without core loss 1. Applied the allowed DC current 2. Temperature measured by digital surface thermometer Isat(A) will cause Lo to drop approximately 20% Saturation Current (Isat) Mechanical Performance Test Solderability Test More than 90% of the terminal electrode should be covered with solder. Preheating Dipping 230C Natural cooling Preheat : 150C, 60sec. Solder : Sn-Ag3.0-Cu0.5 Solder Temperature : 2305C Flux for lead free : rosin Dip Time : 41sec. 150C 60 seconds 41 seconds Solder Heat Resistance 1. Appearance : No significant abnormality 2. Inductance change : Within 20% Preheating 260C Dipping Natural cooling Preheat : 150C, 60sec. Solder : Sn-Ag3.0-Cu0.5 Solder Temperature : 2605C Flux for lead free : rosin Dip Time : 100.5sec. 150C 60 seconds 100.5 seconds Reliability Test High Temperature Life Test Temperature : 1255C Time : 50012 hours Measure at room temperature after placing for 2 to 3 hrs. 1. Appearance : No damage 2. Inductance : Within 20% of initial value. No disconnection or short circuit. Temperature : -555C Time : 50012 hours Measure at room temperature after placing for 2 to 3 hrs. Conditions of 1 cycle. Step 1 2 3 4 Temperature (C) -553 Room Temperature +1253 Room Temperature Times (min.) 303 Within 3 303 Within 3 Low Temperature Life Test Thermal Shock Total : 5 cycles Measure at room temperature after placing for 2 to 3 hrs. Humidity Resistance 1. Appearance : No damage 2. Inductance : Within 20% of initial value. No disconnection or short circuit. Temperature : 405C Humidity : 90% to 95% Applied Current : Rated Curent Time : 50012 hours Measure at room temperature after placing for 2 to 3 hrs. NOTE : Specifications subject to change without notice. Please check our website for latest information. 05.05.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 3 HIGH CURRENT POWER INDUCTORS 8. SOLDERIND AND MOUNTING : 8-1. Recommended PC Board Pattern ( Unit : mm ) 7.5 2.5 SSL0605 SERIES 8-2. Soldering Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. 8-2.1 Solder Re-flow : Recommended temperature profiles for re-flow soldering in Figure 1. 8-2.2 Soldering Iron (Figure 2) : Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. Note : a) Preheat circuit and products to 150C. b) 280C tip temperature (max) c) Never contact the ceramic with the iron tip d) 1.0mm tip diameter (max) e) Use a 20 watt soldering iron with tip diameter of 1.0mm f) Limit soldering time to 3 secs. Preheating TEMPERATURE C 250~260 230 180 150 Soldering 4.5 10s max. TEMPERATURE C Natural cooling Preheating 280 260 150 Soldering Natural cooling 60~120s 30~60s Over 1min. Gradual Cooling Within 3secs. Figure 1. Re-flow Soldering Figure 2. Iron Soldering NOTE : Specifications subject to change without notice. Please check our website for latest information. 05.05.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 4 HIGH CURRENT POWER INDUCTORS 9. PACKAGING INFORMATION : 9-1. Reel Dimension SSL0605 SERIES COVER TAPE 2.00.5 D B OC A EMBOSSED CARRIER Type 13" x 16mm A(mm) 16.00.5 B(mm) 752 C(mm) 13.50.5 D(mm) 330 9-2 Tape Dimension 1.750.1 4.00.1 2.00.1 O1.5+0.1 t W 0.15 MIN P Ao Bo Ko Series SSL0605 Ao(mm) 7.20.1 Bo(mm) 7.20.1 Ko(mm) 5.40.1 P(mm) 12.00.1 W(mm) 16.00.3 t(mm) 0.350.05 9-3 Packaging Quantity Size Chip / Reel Inner Box Carton SSL0605 900 3600 7200 NOTE : Specifications subject to change without notice. Please check our website for latest information. 05.05.2008 SUPERWORLD ELECTRONICS (S) PTE LTD PG. 5 |
Price & Availability of SSL0605 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |