 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT GLASS PASSIVATED HIGH EFFICIENCY SILICON RECTIFIER VOLTAGE RANGE 50 - 1000 Volts CURRENT 3.0 Amperes FEATURE *Sm al l S u r f ac e M o u n t i n g T y p e. (SMP) * Low forward voltage, high current capability * Low leakage current * Glass passivated junction * High temperature soldering guaranteed : 260oC/10 seconds at terminals 0.081 (2.05) 0.077 (1.95) (3) HPL31PT THRU HPL38PT PROVISIONAL SPEC. SMP 0.170 (4.31) 0.163 (4.15) (1) 0.077 (1.95) 0.073 (1.85) 0.005 (0.15 Min.) (2) 0.019 (0.50 Min.) 0.045 (1.16) 0.042 (1.07) 0.019 (0.50 Min.) 0.264 (6.70) 0.254 (6.46) 0.212 (5.38) 0.208 (5.29) CIRCUIT 2 1 0.055 (1.40) 0.051 (1.30) 3 Dimensions in inches and (millimeters) SMP UNITS Volts Volts Volts Amps MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current TL = 100 C Peak Forward Surge Current 8.3 ms single half sine-wave IFSM superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range CJ TJ, TSTG 70 -65 to +150 50 pF o o SYMBOL VRRM VRMS VDC IO HPL31PT HPL32PT HPL33PT HPL34PT HPL35PT HPL36PT HPL37PT HPL38PT 50 35 50 100 70 100 200 140 200 300 210 300 3.0 400 280 400 600 420 600 800 560 800 1000 700 1000 100 Amps C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 3.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A @ TA = 25oC @ TA = 100oC IR 500 trr 50 70 uAmps nSec 2004-7 SYMBOL VF HPL31PT HPL32PT HPL33PT HPL34PT HPL35PT HPL36PT HPL37PT HPL38PT UNITS Volts uAmps 1.0 1.3 5.0 1.5 1.7 RATING CHARACTERISTIC CURVES ( HPL31PT THRU HPL38PT ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) 0 PULSE GENERATOR (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. 1cm SET TIME BASE FOR 10/20 nS/cm -0.25A AVERAGE FORWARD CURRENT, ( A ) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 3.0 2.5 2.0 1.5 1.0 0.5 0 0 Single Phase Half Wave 60Hz Resistive or Inductive Load (+) 25 Vdc (approx) (-) D.U.T 25 50 75 100 125 150 175 LEAD TEMPERATURE ( OC ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PL3 5PT 6P L3 HP PL3 ~H L34 HP 10 TJ =100oC 0.1 1.0 TJ =25oC HP TJ =25oC .01 0.1 .01 0 20 40 60 80 100 120 140 .001 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, ( V ) 1.8 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, ( A ) 120 JUNCTION CAPACITANCE, ( pF ) 100 80 60 40 20 0 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 200 100 60 40 20 10 6 4 2 1 .1 .2 FIG. 6 - TYPICAL JUNCTION CAPACITANCE HPL3 1PT~ HPL3 8.3ms Single Half Sine-Wave (JEDEC Method) 5PT HPL3 6PT~ HPL3 8PT .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) HP L3 7P TJ =125 C L31 PT TJ =25oC T~ o 1.0 PT ~H HP L3 8P T 100 Pulse Width = 300uS 1% Duty Cycle 3PT T 40 100 |
Price & Availability of HPL35PT
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |