 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DATA SHEET 1/2/4/8 GBPS 850NM PIN + PREAMP LC ROSA PACKAGE HFD7180-XXX FEATURES: LC ROSA HFD7180-413 includes flex circuit LC ROSA HFD7180-001 leaded package High performance GaAs PIN photodiode with separate transimpedance amplifier Low electrical parasitic TO46 package Data rates from 1Gbps to 8.5Gbps Received signal strength indicator with bandwidth select Low bias currents and voltages Low power dissipation The HFD7180-xxx use a high-performance GaAs PIN photo-detector packaged with a transimpedance amplifier designed to meet performance requirements for data rates up to 8.5Gbps data communication over multi-mode optical fiber at 850nm. Applications include Ethernet, Fiber Channel and ATM protocols. The optical assembly is designed to interface either 50m or 62.5m multimode fiber. The HFD7180-xxx is designed to be paired with AOC VCSEL TOSA products (see data sheets for HFE719x products). Part Number HFD7180-001 HFD7180-413 Description 5 pin LC ROSA, with separate PD bias 5 pin LC ROSA, with separate PD bias, with flex circuit HFD7180-XXX 1/2/4/8 GBPS 850NM PIN + PREAMP ABSOLUTE MAXIMUM RATINGS Parameter Storage temperature Case Operating temperature Lead solder temperature Power Supply Voltage Incident Optical Power Rating -40oC to +95oC -20o to +95oC 260oC, 10 seconds -0.5V to 4V +3 dBm average, +6 dBm peak NOTICE: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operations section for extended periods of time may affect reliability. NOTICE: The inherent design of this component causes it to be sensitive to electrostatic discharge (ESD). To prevent ESD-induced damage and/or degradation to equipment, take normal ESD precautions when handling this product. HFD7180-XXX ELECTRICAL-OPTICAL CHARACTERISTICS 3.0V ICC ORL p Resp VPD PMAX Vo (pk-pk) T BW BWLF Zout S22 AC coupled TA=25oC dB Differential Power Supply 5MHz -50 50 ps 7 Deterministic Jitter Random Jitter RL=50 AC coupled PR,OMA=-12dBm RL=50 DJTIA RJTIA 20 3 40 5 ps ps 8 9 AC coupled HFD7180-XXX 1/2/4/8 GBPS 850NM PIN + PREAMP NOTES 1. 2. PR is the average optical power at the fiber face. PR,OMA is the peak to peak optical power at the fiber face (Optical Modulation Amplitude) 6. 7. times. T2TIA = T2MEASURED - T2OPTICAL Value shown is with no external power supply filtering. Group delay is a sensitive measurement to package interface, and includes the effects of PD, TIA and package. Measurement is made with TO leads as short as possible. DJTIA is specified as contributed DJ by the TIA, obtained from DJ2TIA = DJ2TOTAL - DJ2OPTICAL RJTIA is specified as contributed DJ by the TIA, obtained from RJ2TIA = RJ2TOTAL - RJ2OPTICAL PR ,OMA 2 PR (ER - 1) ER + 1 8. where ER is the extinction ratio (linear) of the optical source. 3. Bandwidth and Low Frequency Cutoff are measured with a small signal sinusoidal light source with -10dBm average power Sensitivity is measured with an optical source with an extinction ratio of 3dB. For sensitivity measurements at 2 and 4Gbps, bandwidth limiting of the TIA is assumed to be implemented at the front end of the post amplifier. Rise/Fall times are corrected for optical source Rise/Fall 9. 4. 10. The electrical performance of the ROSA is dependent upon the quality of the electrical connection between the TO can and the circuit board. AOC cannot guarantee all performance specifications for parts without the flex circuit attached. 5. PINOUT PIN 1 2 3 4 5 HFE7180-001 GND (Case) OUTN VCC VPD OUTP PIN 1 2 3 4 5 6 VCC Case OUTN OUTP Case PD_Bias HFE7180-413 HFD7180-XXX INTERFACE EXAMPLE Optional 100 differential termination for high impedance limiting amplifiers is shown in red RECOMMENDED BIAS FILTER NETWORK Note, better performance will be obtained if a ferrite bead is used in place of the inductor. HFD7180-XXX 1/2/4/8 GBPS 850NM PIN + PREAMP MECHANICAL DIMENSIONS HFD 7180-001 (for reference only): Dimensions in Inches HFD7180-XXX MECHANICAL DIMENSIONS HFD 7180-413 (for reference only): Dimensions in Inches HFD7180-XXX 1/2/4/8 GBPS 850NM PIN + PREAMP ADVANCED OPTICAL COMPONENTS Finisar's ADVANCED OPTICAL COMPONENTS division was formed through strategic acquisition of key optical component suppliers. The company has led the industry in high volume Vertical Cavity Surface Emitting Laser (VCSEL) and associated detector technology since 1996. VCSELs have become the primary laser source for optical data communication, and are rapidly expanding into a wide variety of sensor applications. VCSELs' superior reliability, low drive current, high coupled power, narrow and circularly symmetric beam and versatile packaging options (including arrays) are enabling solutions not possible with other optical technologies. ADVANCED OPTICAL COMPONENTS is also a key supplier of Fabrey-Perot (FP) and Distributed Feedback (DFB) Lasers, and Optical Isolators (OI) for use in single mode fiber data and telecommunications networks AOC CAPABILITIES ADVANCED OPTICAL COMPONENTS' advanced capabilities include: 1, 2, 4, 8, and 10Gbps serial VCSEL solutions 1, 2, 4, 8, and 10Gbps serial SW DETECTOR solutions VCSEL and detector arrays 1, 2, 4, 8, and 10Gbps FP and DFB solutions at 1310 and 1550nm 1, 2, 4, 8, and 10Gbps serial LW DETECTOR solutions Optical Isolators from 1260 to 1600nm range Laser packaging in TO46, TO56, and Optical subassemblies with SC, LC, and MU interfaces for communication networks VCSELs operating at 670nm, 780nm, 980nm, and 1310nm in development Sensor packages include surface mount, various plastics, chip on board, chipscale packages, etc. Custom packaging options LOCATION Allen, TX - Business unit headquarters, VCSEL wafer growth, wafer fabrication and TO package assembly. Fremont, CA - Wafer growth and fabrication of 1310 to 1550nm FP and DFB lasers. Shanghai, PRC - Optical passives assembly, including optical isolators and splitters. SALES AND SERVICE Finisar's ADVANCED OPTICAL COMPONENTS division serves its customers through a worldwide network of sales offices and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact a nearby sales office or call the number listed below. Phone:1-866-MY-VCSEL USA (toll free) 1-214-509-2700 USA (Direct dial) 44 (0) 174 336 5533 Europe 886-935-409898 China & Taiwan 81-90-4437-1130 Japan 82-11-220-6153 Asia Pacific & Korea Fax: 1-214-509-3709 USA Email: support@adopco.com WEB: www.finisar.com/aoc.php (c)2007 Finisar Corporation. All rights reserved. Finisar is a registered trademark of Finisar Corporation. Features and specifications are subject to change without notice. 9/07 Rev. C |
Price & Availability of HFD7180-001
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |