View VRP2-50E1A0_4327211.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NON-ISOLATED DC/DC CONVERTERS
5 Vdc - 13.8 Vdc Input 0.6 Vdc - 5.0 Vdc/50 A Output
xRP2-50E1A0
* * * * * * * Non-Isolated High Efficiency
RoHS Compliant
* * * * *
Rev.E
Output Over-Voltage Shutdown OCP/SCP Low Output Ripple Power Good Signal Remote On/Off
Fixed Switching Frequency Low Cost Excellent Thermal Performance Wide Input Voltage Range Wide Output Trim Range
Description
The xRP2-50E1A0 is a non-isolated dc/dc converter that operates over a wide range of input voltage (Vin = 5 Vdc - 13.8 Vdc). This unit can provide a precisely regulated output voltage from 0.6 Vdc to 5.0 Vdc and can deliver up to 50 A of output current. This unit is designed to be highly efficient and low cost. The converter is provided in an industry standard package.
Part Selection
Output Voltage 0.6 V - 5.0 V Input Voltage 5.0 V - 13.8 V Max. Output Current 50 A Max. Output Power 250 W Typical Efficiency (Vo=1.8 Vdc 86% Part Number Horizontal Mount 0RP2-50E1A0 Part Number Vertical Mount VRP2-50E1A0
Notes: 1. All part numbers above indicate RoHS 6. Change the second letter "R" to "7" for RoHS 5 part numbers. 2. Add "G" suffix at the end of the model numbers listed above to indicate "Tray Packaging".
Absolute Maximum Ratings
Parameter Input Voltage (continuous) Output Enable Terminal Voltage Ambient Temperature Storage Temperature Min -0.3 V -0.3 V 0 C -55 C Typ Max 15 V 15 V 70 C 125 C Notes
Input Specifications
Parameter Input Voltage Vo 2.8 V Vo > 2.8 V Input Current (full load) Input Reflected Ripple Current (pk-pk) Input Reflected Ripple Current (rms) I t Inrush Current Transient Turn-on Voltage Threshold Under Voltage Threshold
2
Min 5V 1.8*Vo 4.4 V 4.0 V
Typ 12 V 12 V 35 mA 10 mA 4.6 V 4.3 V
Max 13.8 V 13.8 V 38 A 1A s 4.8 V 4.6 V
2
Notes
With simulated source impedance of 1 uH, 5 Hz to 20 MHz. Use a 1000 uF/16 V electrolytic capacitor with ESR=0.1 ohm max, at 100 kHz at 25C.
Note: All specifications are typical at 25 C unless otherwise stated.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
5 Vdc - 13.8 Vdc Input 0.6 Vdc - 5.0 Vdc/50 A Output
Output Specifications
Parameter Output Voltage Set Point Accuracy Vo1 V Vo1 V Load Regulation Vo2.5 V Vo2.5 V Line Regulation Vo2.5 V Vo2.5 V Regulation Over Temperature (0 C to +70 C) Output Current Current Limit Threshold Output Ripple and Noise (pk-pk) Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.5 V Vo=1.0 V Vo=0.6 V Output Ripple and Noise (rms) Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.5 V Vo=1.0 V Vo=0.6 V Turn On Time Rise Time Overshoot at Turn on and off Output Capacitance ESR1 m Transient Response 50% ~ 100% Max Load Settling Time 100% ~ 50% Max Load Settling Time VO=All 300 mV 100 uS 300 mV 100 uS Test conditions: di/dt = 10 A/uS; Vin =12 V; Co=0 uF. 0A 105% Io 0 uF 130% Io 0.3% Vo 9 mV 0.02% Vo/C 50 A 180% Io 110 mV 100 mV 100 mV 80 mV 60 mV 60 mV 35 mV 35 mV 35 mV 30 mV 25 mV 25 mV 10 mS 3 mS 0.5% 4700 uF 0.6% Vo 12 mV Min -1.5 % Vo -10 mV Typ Max +1.5 % Vo +10 mV Notes Vin=Vinmin, Io=Iomax
Test conditions: 0-20MHz BW, with a 1F ceramic capacitor and a 10 uF Tantalum cap at output.
Note: All specifications are typical at nominal input, full load at 25C unless noted.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
5 Vdc - 13.8 Vdc Input 0.6 Vdc - 5.0 Vdc/50 A Output
General Specifications
Parameter Efficiency Vo=5.0 V Vo=3.3 V Vo=2.5 V Vo=1.8 V Vo=1.5 V Vo=1.2 V Vo=1.0 V Vo=0.6 V Switching Frequency Output Voltage Trim Range Over Voltage Protection MTBF Dimensions (horizontal mount) Inches (L x W x H) Millimeters (L x W x H) Dimensions (vertical mount) Inches (L x W x H) Millimeters (L x W x H) Weight 0.6 V 110% Vo,set 93% 91% 88% 86% 84% 82% 75% 68% 330 kHz 115%Vo,set 3,361,100 hours 5V 130%Vo,set Trim pin is open, Vo = 0.6 V. Vin=12 V, Io=full load. Calculated Per Bell Core SR332 (IO =40 A, Vo=1.92 V; Vin=12 V; Ta = 25 C, 100LFM forced air flow.) Min Typ Max Notes
1.45 x 1.1 x 0.783 36.83 x 27.94 x 19.9 1.45 x 1.1 x 0.743 36.83 x 27.94 x 18.87 28.5 g -
Note: All specifications are typical at 25 C unless otherwise stated.
Control Specifications
Parameter Remote On/Off (Active High) Signal Low (Unit Off) Signal High (Unit On) Current Source/Sink PwGood (PowerGood) PwGood = High = Power Good PwGood = Low = Power Not Good 2.4 V 0V 5.25 V 2 mA 0.4 V 4 mA -0.3 V 2V 0 mA 0.8 V Vin,max 3.3 mA Remote On/Off pin is open, unit is off. Min Typ Max Notes
Output Trim Equation
The Trim resistor should be connected between the Trim+ pin and Trim- pin.
Vout
R trim
1 .2 = ( K ) Vo - 0 . 6
Module
Trim+ Rtrim Trim-
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
5 Vdc - 13.8 Vdc Input 0.6 Vdc - 5.0 Vdc/50 A Output
Efficiency Data
Efficiency Curve Vo=0.6 V 85.0% 80.0% Efficiency
Efficiency
95.0% 90.0% 85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 5V 12 V 13.8 V Efficiency Curve Vo=1.2 V
75.0% 70.0% 65.0% 60.0% 55.0% 50.0% 5 12.5 25 37.5 50 Output Current (A) 5V 12 V 13.8 V
5
12.5
25
37.5
50
Output Current (A)
Efficiency Curve Vo=1.8 V 95.0% 90.0% Efficiency
100.0% 95.0%
Efficiency Curve Vo=2.5 V
Efficiency
85.0% 80.0% 75.0% 70.0% 65.0% 60.0% 5 12.5 25 37.5 50 Output Current (A) 5V 12 V 13.8 V
90.0% 85.0% 80.0% 75.0% 70.0% 65.0% 5 12.5 25 37.5 50 5V 12 V 13.8 V
Output Current (A)
Efficiency Curve Vo=3.3 V 100.0% 95.0%
Efficiency Curve Vo=5.0 V 100.0% 95.0% Efficiency 90.0% 85.0% 80.0% 75.0% 70.0% 65.0% 9V 12 V 13.8 V
6V 12 V 13.8 V
Efficiency
90.0% 85.0% 80.0% 75.0% 70.0% 65.0% 5 12.5 25 37.5 50
5
12.5
25
37.5
50
Output Current (A)
Output Current (A)
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
5 Vdc - 13.8 Vdc Input 0.6 Vdc - 5.0 Vdc/50 A Output
Thermal Derating Curve
Vin=12 V, Vo=0.6 V
Vin=12 V, Vo=1.2 V
Vin=12 V, Vo=1.8 V
Vin=12 V, Vo=2.5 V
Vin=12 V, Vo=3.3 V
Vin=12 V, Vo=5.0 V
Note: Maximum junction temperature of semiconductors derated to 120C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
5 Vdc - 13.8 Vdc Input 0.6 Vdc - 5.0 Vdc/50 A Output
Ripple and Noise Waveforms
12 Vdc input, 0.6 Vdc/50 A output
12 Vdc input, 1.2 Vdc/50 A output
12 Vdc input, 1.8 Vdc/50 A output
12 Vdc input, 2.5 Vdc/50 A output
12 Vdc input, 3.3 Vdc/50 A output
12 Vdc input, 5.0 Vdc/50 A output
Note: Ripple and noise at full load, 0-20 MHz BW, with a 10 uF and a 1uF ceramic cap at the output, and Ta=25 deg C.
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
5 Vdc - 13.8 Vdc Input 0.6 Vdc - 5.0 Vdc/50 A Output
Transient Response Waveforms
Vout= 0.6 V 0%-50% Load Transient
Vout=0.6 V 50%-0% Load Transient
Vout=1.2 V 0%-50% Load Transient
Vout=1.2 V 50%-0% Load Transient
Vout=1.8 V 0%-50% Load Transient
Vout=1.8 V 50%-0% Load Transient
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
5 Vdc - 13.8 Vdc Input 0.6 Vdc - 5.0 Vdc/50 A Output
Transient Response Waveforms (continued)
Vout= 2.5 V 0%-50% Load Transient
Vout=2.5 V 50%-0% Load Transient
Vout=3.3 V 0%-50% Load Transient
Vout=3.3 V 50%-0% Load Transient
Vout=5 V 0%-50% Load Transient
Vout=5 V 50%-0% Load Transient
Note: Transient response at di/dt = 10 A/uS, with extemal electrolytic cap 4700 uF, and Ta=25 deg C. .
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
5 Vdc - 13.8 Vdc Input 0.6 Vdc - 5.0 Vdc/50 A Output
Mechanical Outline 0RP2-50E1A0
Pin Connections
Pin 1 2 3 4 5 6 7 8 Function Vout Vout Vout GND GND Enable TrimTrim+ Pin 9 10 11 12 13 14 15 Function PwGOOD SenseSense+ Vin Vin GND GND
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 * Tel 201-432-0463 * Fax 201-432-9542 * www.belfuse.com
NON-ISOLATED DC/DC CONVERTERS
5 Vdc - 13.8 Vdc Input 0.6 Vdc - 5.0 Vdc/50 A Output
Mechanical Outline (continued) VRP2-50E1A0
Pin Connections
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Function Vout Vout Vout GND GND Enable TrimTrim+ PwGOOD SenseSense+ Vin Vin GND GND
RoHS Compliance
Complies with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products.
(c)2007 Bel Fuse Inc. Specifications subject to change without notice. 080307
CORPORATE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com
FAR EAST Bel Fuse Ltd. 8F/ 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com
EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com

▲Up To Search▲

Price & Availability of VRP2-50E1A0

	To Download VRP2-50E1A0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .