View NSPU510CS_4327037.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

No. STSE-CU7061A
SPECIFICATIONS FOR NICHIA UV
MODEL : NSPU510CS
LED
NICHIA CORPORATION
-0-
Nichia STSE-CU7061A
1.SPECIFICATIONS
(1) Absolute Maximum Ratings Item Forward Current Pulse Forward Current Allowable Reverse Current Power Dissipation Operating Temperature Storage Temperature Soldering Temperature
IFP Conditions :
Symbol IF IFP IR PD Topr Tstg Tsld
and
Absolute Maximum Rating 20 80 85 80 -30 ~ + 85 -40 ~ +100 265C for 10sec.
Duty < 1/10 =
(Ta=25C) Unit mA mA mA mW C C
Pulse Width < 10msec. =
(2) Initial Electrical/Optical Characteristics Item Symbol Forward Voltage VF Peak Wavelength Rank Ub P Spectrum Half Width Rank 7 Po Rank 8 Po Optical Power Output Rank 9 Po
Condition IF=15[mA] IF=15[mA] IF=15[mA] IF=15[mA] IF=15[mA] IF=15[mA]
Min. 370 4800 6800 9600
Typ. (3.6) (375) (15) -
(Ta=25C) Max. Unit 4.0 V 380 nm nm W 6800 W 9600 W 13600
Optical Power Output Measurement allowance is 10%. Peak Wavelength Measurement allowance is 3nm. One delivery will include up to three different ranks of the products. The quantity-ratio of the three ranks is decided by Nichia.
2.INITIAL
OPTICAL/ELECTRICAL
CHARACTERISTICS
Please refer to figure's page.
3.OUTLINE
DIMENSIONS
AND
MATERIALS
Epoxy Resin (over Diffusion) Ag plating Copper Alloy
Please refer to figure's page. Material as follows ; Resin(Mold) : Leadframe :
-1-
Nichia STSE-CU7061A
4.PACKAGING
* The LEDs are packed in cardboard boxes after packaging in anti-electrostatic bags. Please refer to figure's page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity * In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. * The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. * The boxes are not water resistant and therefore must be kept away from water and moisture. * When the LEDs are transported, we recommend that you use the same packing method as Nichia.
5.LOT
NUMBER
The first six digits number shows lot number. The lot number is composed of the following characters; - Year ( 6 for 2006, 7 for 2007 ) - Month ( 1 for Jan., 9 for Sep., A for Oct., - Nichia's Product Number - Ranking by Wavelength - Ranking by Optical Power Output
B for Nov. )
-2-
Nichia STSE-CU7061A
6.RELIABILITY
(1) TEST ITEMS AND RESULTS
Test Item Resistance to Soldering Heat Solderability Temperature Cycle Moisture Resistance Cyclic High Temperature Storage Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Standard Test Method JEITA ED-4701 300 302 JEITA ED-4701 300 303 JEITA ED-4701 100 105 JEITA ED-4701 200 203 JEITA ED-4701 200 201 JEITA ED-4701 100 103 JEITA ED-4701 200 202 Test Conditions Tsld=260 5C, 10sec. 3mm from the base of the epoxy bulb Tsld=235 5C, (using flux) 5sec. Note 1 time 1 time over 95% 100 cycles 10 cycles 1000hrs. RH=90% 1000hrs. 1000hrs. IF=15mA IF=10mA 1000hrs. 500hrs. 1000hrs. Number of Damaged 0/22 0/22 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50
-40C ~ 25C ~ 100C ~ 25C 30min. 5min. 30min. 5min. 25C ~ 65C ~ -10C 90%RH 24hrs./1cycle Ta=100C Ta=60C, Ta=-40C Ta=25C,
60C, RH=90%, Ta=-30C,
IF=15mA
(2) CRITERIA FOR JUDGING DAMAGE Item Forward Voltage Symbol VF Test Conditions IF=15mA Criteria for Judgement Min. Max. U.S.L.*) 1.1
Optical Power Output Po *) U.S.L. : Upper Standard Level
IF=15mA L.S.L.**) 0.5 **) L.S.L. : Lower Standard Level
-3-
Nichia STSE-CU7061A
7.CAUTIONS
(1) Cautions * The devices are UV light LEDs. The LED during operation radiates intense UV light, which precautions must be taken to prevent looking directly at the UV light with unaided eyes. Do not look directly into the UV light or look through the optical system. When there is a possibility to receive the reflection of light, protect by using the UV light protective glasses so that light should not catch one's eye directly. * The caution label is attached to cardboard box.
UV LED
LED
1M LED
LED RADIATION
DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LED PRODUCT
(2) Lead Forming * When forming leads, the leads should be bent at a point at least 3mm from the base of the lead. Do not use the base of the leadframe as a fulcrum during lead forming. * Lead forming should be done before soldering. * Do not apply any bending stress to the base of the lead. The stress to the base may damage the LED's characteristics or it may break the LEDs. * When mounting the LEDs onto a printed circuit board, the holes on the circuit board should be exactly aligned with the leads of the LEDs. If the LEDs are mounted with stress at the leads, it causes deterioration of the lead and this will degrade the LEDs. (3) Storage * The LEDs should be stored at 30C or less and 70%RH or less after being shipped from Nichia and the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material. * Nichia LED leadframes are silver plated copper alloy. The silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the LEDs be used as soon as possible. * Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can occur. (4) Static Electricity * Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. * All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts LEDs. * When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). The LEDs should be used the light detector etc. when testing the light-on. Do not stare into the LEDs when testing. * Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA)
-4-
Nichia STSE-CU7061A (5) Soldering Conditions * Nichia LED leadframes are silver plated copper alloy. This substance has a low thermal coefficient (easily conducts heat). Careful attention should be paid during soldering. * Solder the LED no closer than 3mm from the base of the epoxy bulb. Soldering beyond the base of the tie bar is recommended. * Recommended soldering conditions
Pre-Heat Pre-Heat Time Solder Bath Temperature Dipping Time Dipping Position Dip Soldering 120C Max. 60 seconds Max. 260C Max. 10 seconds Max. No lower than 3 mm from the base of the epoxy bulb. Hand Soldering 350C Max. Temperature 3 seconds Max. Soldering Time No closer than 3 mm from the Position base of the epoxy bulb.
* Although the recommended soldering conditions are specified in the above table, dip or hand soldering at the lowest possible temperature is desirable for the LEDs. * A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. * Dip soldering should not be done more than one time. * Hand soldering should not be done more than one time. * Do not apply any stress to the lead particularly when heated. * The LEDs must not be repositioned after soldering. * After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to room temperature. * Direct soldering onto a PC board should be avoided. Mechanical stress to the resin may be caused from warping of the PC board or from the clinching and cutting of the leadframes. When it is absolutely necessary, the LEDs may be mounted in this fashion but the User will assume responsibility for any problems. Direct soldering should only be done after testing has confirmed that no damage, such as wire bond failure or resin deterioration, will occur. Nichia's LEDs should not be soldered directly to double sided PC boards because the heat will deteriorate the epoxy resin. * When it is necessary to clamp the LEDs to prevent soldering failure, it is important to minimize the mechanical stress on the LEDs. * Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures may cause failure of the LEDs. (6) Heat Generation * Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. * The operating current should be decided after considering the ambient maximum temperature of LEDs. (7) Cleaning * It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. * Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur.
-5-
Nichia STSE-CU7061A (8) Safety Guideline for Human Eyes * In 1993, the International Electric Committee (IEC) issued a standard concerning laser product safety (IEC 825-1). Since then, this standard has been applied for diffused light sources (LEDs) as well as lasers. In 1998 IEC 60825-1 Edition 1.1 evaluated the magnitude of the light source. In 2001 IEC 60825-1 Amendment 2 converted the laser class into 7 classes for end products. Components are excluded from this system. Products which contain visible LEDs are now classified as class 1. Products containing UV LEDs are class 1M. Products containing LEDs can be classified as class 2 in cases where viewing angles are narrow, optical manipulation intensifies the light, and/or the energy emitted is high. For these systems it is recommended to avoid long term exposure. It is also recommended to follow the IEC regulations regarding safety and labeling of products. (9) Others * NSPU510CS complies with RoHS Directive. * This LED also emits visible light. Please take notice of visible light spectrum, in case you use this LED as light source of sensors etc. * The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia's sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). * User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis. * The formal specifications must be exchanged and signed by both parties before large volume purchase begins. * The appearance and specifications of the product may be modified for improvement without notice.
-6-
Forward Voltage vs. Forward Current
100 50 20 10 5 Ta=25C Relative Power Output (a.u.) Forward Current IFP (mA)
Forward Current vs. Relative Power Output
Allowable Forward Current IFP (mA) 6 5 4 3 2 1 0 0 20 40 60 80 100 Forward Current IFP (mA) Ta=25C
Duty Ratio vs. Allowable Forward Current
200 Ta=25C 100 80 50 30 20 10
1 2.5
3.0 3.5 4.0 4.5 5.0 Forward Voltage VF (V)
1
5 10 20 50 100 Duty Ratio (%)
Ambient Temperature vs. Forward Voltage
3.9 Forward Voltage VF (V) 3.8 3.7 3.6 3.5 3.4 3.3 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) IFP=15mA Relative Power Output (a.u.)
Ambient Temperature vs. Relative Power Output
Allowable Forward Current IF (mA) 2.0 IFP=15mA 1.0
Ambient Temperature vs. Allowable Forward Current
25 20 15 10 4 0 0 20 40 60 80 100 Ambient Temperature Ta (C)
-7-
0.5
0.2 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C)
Nichia STSE-CU7061A
Model
NSPU510CS
NICHIA CORPORATION
Title No.
CHARACTERISTICS
070511764601
Forward Current vs. Peak Wavelength
Relative Emission Intensity (a.u.) 381 Peak Wavelength p (nm) Ta=25C 379 377 375 373 371 1 5 10 20 50 100 Forward Current IFP (mA)
Spectrum
1.2 1.0 0.8 0.6 0.4 0.2 0 300 350 400 450 500 550 600 Wavelength (nm) Ta=25C IF=15mA
Ambient Temperature vs. Peak Wavelength
381 Relative Power Output (a.u.) Peak Wavelength p (nm) IFP=15mA 379 377 375 373 371 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C)
Directivity
1.0 Ta=25C IFP=15mA 0 10 20 30 40 50 0.5 60 70 80 0 90 60 30 Radiation Angle 0 0.5 90 1.0
-8-
Nichia STSE-CU7061A
Model
NSPU510CS
NICHIA CORPORATION
Title No.
CHARACTERISTICS
070511764611
0.5 0.05
Anode
Internal circuit
A
1.5MAX.
5.3 0.5
Cathode (2.5)
1.1
Protection device
5 1
K
7.1 8.3 12.1 0.5
0.3 0.3
Stopper
5.6
-9-
(2)
28.6 1
1
ITEM RESIN LEAD FRAME
MATERIALS Epoxy Resin (over Diffusion) Ag Plating Copper Alloy Nichia STSE-CU7061A
Please note that the bare copper alloy showing at the cut end of the lead frame may be corroded under certain conditions. LEDs have some sharp edges and points, particularly lead frames. Please handle with care so as to avoid injuries. NSPU510CS has a protection device built in as a protection circuit against static electricity.
Model
NSPU510CS
Unit mm 3/1 Scale Allow 0.2
NICHIA CORPORATION
Title No.
OUTLINE DIMENSIONS
070507764621
Print
NICHIA
Cardboard
UV LED
TYPE NSPUxxxxx LOT QTY xxxxxxpcs
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Anti electrostatic bag
UV LED
LE D
1M LE D
L ED R A D IA TIO N
D O N O T V IE W D IRE CT LY W IT H O PT IC AL IN ST RU M E N T S C LA SS 1M LE D PR O D U CT
The quantity is printed on this bag.
CAUTION TO ELECTROSTATIC DAMAGE
Label
NICHIA
UV
TYPE LOT QTY
LED
NSPUxxxxx xxxxxxPCS RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
-10-
Cardboard
Caution Label
UV LED
LED
1M LED
LED RADIATION
DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LED PRODUCT
Put the label and caution label on the cardboard box.
Nichia STSE-CU7061A
Cardboard box 360 135 215 4t
Model
NSPUxxxxx
NICHIA CORPORATION
One box contains 8 bags at maximum.
Title No.
PACKING
070507764631
Print
Cardboard
NICHIA
UV LED
TYPE NSPUxxxxx LOT QTY xxxxxxpcs
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Anti-electrostatic bag
UV LED
LE D L ED R A D IA TIO N
D O N O T V IE W D IRE CT LY W IT H O PT IC AL IN ST RU M E N T S C LA SS 1M LE D PR O D U CT
The quantity is printed on this bag.
1M LE D
CAUTION TO ELECTROSTATIC DAMAGE
Caution Label
Cardboard box A
LED
1M LED
UV LED
LED RADIATION
DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LED PRODUCT
Label
-11Cardboard
NICHIA
Put the caution label on the cardboard box A.
UV
TYPE LOT QTY
LED
NSPUxxxxx xxxxxxPCS RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Put the label on the cardboard box B.
Nichia STSE-CU7061A
Cardboard box B 360 135 215 4t
The cardboard box B contains 2 cardboard box A at maximum.
Model
NSPUxxxxx
NICHIA CORPORATION
Title No.
PACKING
070507764641
Print
Cardboard Anti-electrostatic bag
NICHIA
UV LED
TYPE NSPUxxxxx LOT QTY xxxxxxpcs
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
UV LED
LE D
1M LE D
L ED R A D IA TIO N
D O N O T V IE W D IRE CT LY W IT H O PT IC AL IN ST RU M E N T S C LA SS 1M LE D PR O D U CT
The quantity is printed on this bag.
CAUTION TO ELECTROSTATIC DAMAGE
Label
NICHIA
UV
TYPE LOT QTY
LED
NSPUxxxxx xxxxxxPCS RoHS
Cardboard
Caution Label
-12-
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
UV LED
LED LED RADIATION
DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LED PRODUCT
Cardboard box 425 135 355 4t
1M LED
Put the label and caution label on the cardboard box.
Nichia STSE-CU7061A
Model One box contains 20 bags at maximum.
NSPUxxxxx
NICHIA CORPORATION
Title No.
PACKING
070507764651
Print
NICHIA
Cardboard
UV LED
TYPE NSPUxxxxx LOT QTY xxxxxxpcs
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Anti-electrostatic bag
UV LED
LE D L ED R A D IA TIO N
D O N O T V IE W D IRE CT LY W IT H O PT IC AL IN ST RU M E N T S C LA SS 1M LE D PR O D U CT
The quantity is printed on this bag.
1M LE D
CAUTION TO ELECTROSTATIC DAMAGE
Cardboard box A
Caution Label
UV LED
LED
1M LED
LED RADIATION
DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 1M LED PRODUCT
-13Cardboard The cardboard box B contains 4 cardboard box A at maximum.
Label
Put the caution label on the cardboard box A.
TYPE LOT QTY
NICHIA
UV LED
NSPUxxxxx xxxxxxPCS RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Put the label on the cardboard box B.
Nichia STSE-CU7061A
Cardboard box B 425 135 355 4t
Model
NSPUxxxxx
NICHIA CORPORATION
Title No.
PACKING
070507764661

▲Up To Search▲

Price & Availability of NSPU510CS

	To Download NSPU510CS Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .