View IDT74CBTLV6800_4295195.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

IDT74CBTLV6800 LOW-VOLTAGE 10-BIT BUS SWITCH WITH PRECHARGED OUTPUTS
INDUSTRIAL TEMPERATURE RANGE
LOW-VOLTAGE 10-BIT BUS SWITCH WITH PRECHARGED OUTPUTS
FEATURES:
* * * * * * * Functionally equivalent to QS3800 5 A/B bi-directional switch Isolation under power-off conditions Over-voltage tolerant Latch-up performance exceeds 100mA VCC = 2.3V - 3.6V, Normal Range ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) * Available in QSOP and TSSOP packages
IDT74CBTLV6800
DESCRIPTION:
The CBTLV6800 provides 10-bits of high-speed bus switching with low on-state resistance of the switch allowing connections to be made with minimal propagation delay. The device also precharges the B port to a user-selectable bias voltage (BIASV) to minimize live-insertion noise. The CBTLV6800 is organized as a single 10-bit bus switch with a single output-enable (OE) input. When OE is low, the 10-bit bus switch is on and port A is connected to port B. When OE is high, the switch is open, and a high impedance state exists between the two ports, and port B is precharged to BIASV through the equivalent of a 10-k resistor. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
APPLICATIONS:
* 3.3V High Speed Bus Switching and Bus Isolation
FUNCTIONAL BLOCK DIAGRAM
SIMPLIFIED SCHEMATIC, EACH SWITCH
13 A1 2
SW
BIASV B1
23
A
11 14
B
A10
SW
B10
OE
1
OE
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
1
JUNE 2006
DSC-5739/4
(c) 2006 Integrated Device Technology, Inc.
IDT74CBTLV6800 LOW-VOLTAGE 10-BIT BUS SWITCH WITH PRECHARGED OUTPUTS
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS(1)
Symbol VCC VI IIK TSTG Description SupplyVoltage Range Input Voltage Range Continuous Channel Current Input Clamp Current, VI/O < 0 Storage Temperature Max -0.5 to +4.6 -0.5 to +4.6 128 -50 -65 to +150 Unit V V mA mA C
OE A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 GND
1 2 3 4 5 6 7 8 9 10 11 12
24 23 22 21 20 19 18 17 16 15 14 13
VCC B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 BIASV
NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
FUNCTION TABLE(1)
Input OE L H
NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level Z = High-Impedance
Inputs/Outputs A Port = B Port A Port = Z B Port = BIASV
QSOP / TSSOP TOP VIEW
OPERATING CHARACTERISTICS, TA = 25C(1)
Symbol VCC BIASV VIH VIL TA Parameter Supply Voltage Bias Voltage High-Level Control Input Voltage Low-Level Control Input Voltage Operating Free-Air Temperature VCC = 2.3V to 2.7V VCC = 2.7V to 3.6V VCC = 2.3V to 2.7V VCC = 2.7V to 3.6V Test Conditions Min. 2.3 1.3 1.7 2 -- -- -40 Max. 3.6 VCC -- -- 0.7 0.8 85 C V Unit V V V
NOTE: 1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation.
2
IDT74CBTLV6800 LOW-VOLTAGE 10-BIT BUS SWITCH WITH PRECHARGED OUTPUTS
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified: Operating Conditions: TA = -40C to +85C
Symbol VIK II IOZ IOFF |IO| ICC ICC(1) CI CIO(OFF) VCC = 2.3V Typ. at VCC = 2.5V RON(2) VCC = 3V VI = 2.4V Control Inputs Control Inputs Parameter Control Inputs, Data Inputs Control Inputs Data I/O VCC = 3V, II = -18mA VCC = 3.6V, VI = VCC or GND VCC = 3.6V, VO = 0 or 3.6V, switch disabled VCC = 0, VI or VO = 0 to 3.6V VCC = 3V, BIASV = 2.4V, VO = 0, OE = VCC VCC = 3.6V, IO = 0, VI = VCC or GND VCC = 3.6V, one input at 3V, other inputs at VCC or GND VI = 3V or 0 VO = 3V or 0, switch OFF, BIASV = Open, OE = VCC VI = 0 VI = 1.7V VI = 0 II = 64mA II = 24mA II = 15mA II = 64mA II = 24mA II = 15mA Test Conditions Min. -- -- -- -- 0.25 -- -- -- -- -- -- -- -- -- -- Typ. -- -- -- -- -- -- -- 4 7 5 5 27 5 5 10 Max. -1.2 1 20 50 -- 10 300 -- -- 8 8 40 7 7 15 Unit V A A A mA A A pF pF
NOTES: 1. The increase in supply current is attributable to each current that is at the specified voltage level rather than VCC or GND. 2. This is measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-state resistance is determined by the lower of the voltages of the two (A or B ) terminals.
SWITCHING CHARACTERISTICS
VCC = 2.5V 0.2V Symbol tPD
(1)
VCC = 3.3V 0.3V Max. 0.15 Min. - 1 Max. 0.25 Unit ns
Parameter Propagation Delay A to B or B to A
Min. - 1
tPZH tPZL tPHZ tPLZ
BIASV = 3V or GND OE to A or B BIASV = 3V or GND OE to A or B
4.8
4.5
ns
1
5.6
1
5.5
ns
NOTE: 1. The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance driven by an ideal voltage source (zero output impedance).
3
IDT74CBTLV6800 LOW-VOLTAGE 10-BIT BUS SWITCH WITH PRECHARGED OUTPUTS
INDUSTRIAL TEMPERATURE RANGE
TEST CIRCUITS AND WAVEFORMS TEST CONDITIONS
Symbol VLOAD VIH VT VLZ VHZ CL VCC = 3.3V0.3V 6 3 1.5 300 300 50
(1)
SAME PHASE INPUT TRANSITION tPLH tPHL
Unit V V V mV mV pF
VCC = 2.5V0.2V 2 x Vcc Vcc Vcc / 2 150 150 30
(2)
OUTPUT tPLH OPPOSITE PHASE INPUT TRANSITION tPHL
VIH VT 0V VOH VT VOL VIH VT 0V
Propagation Delay
ENABLE CONTROL INPUT tPZL OUTPUT SWITCH NORMALLY CLOSED LOW tPZH OUTPUT SWITCH NORMALLY OPEN HIGH VLOAD/2 VT tPHZ VT 0V tPLZ DISABLE
VCC 500 Pulse(1, 2) Generator VIN D.U.T. RT 500 CL VOUT
VLOAD Open GND
VIH VT 0V VLOAD/2 VOL + VLZ VOL VOH VOH -VHZ 0V
Test Circuits for All Outputs Enable and Disable Times
DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. NOTES: 1. Pulse Generator for All Pulses: Rate 10MHz; tF 2.5ns; tR 2.5ns. 2. Pulse Generator for All Pulses: Rate 10MHz; tF 2ns; tR 2.5ns.
SWITCH POSITION
Test tPLZ/tPZL tPHZ/tPZH tPD Switch VLOAD GND Open
4
IDT74CBTLV6800 LOW-VOLTAGE 10-BIT BUS SWITCH WITH PRECHARGED OUTPUTS
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
CBTLV XXX XX IDT XX Temp. Range Device Type Package
Q QG PG PGG
Quarter-size Small Outline Package QSOP - Green Thin Shrink Small Outline Package TSSOP - Green
6800
Low-Voltage 10-Bit Bus Switch with Precharged Outputs
74
-40C to +85C
CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138
for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com
5
for Tech Support: logichelp@idt.com

▲Up To Search▲

Price & Availability of IDT74CBTLV6800

	To Download IDT74CBTLV6800 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .