View TEA1750_4274564.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TEA1750
GreenChip III SMPS control IC
Rev. 02 -- 15 December 2008 Product data sheet
1. General description
The GreenChip III is the third generation of green Switched Mode Power Supply (SMPS) controller ICs. The TEA1750 combines a controller for Power Factor Correction (PFC) and a flyback controller. Its high level of integration allows the design of a cost-effective power supply with a very low number of external components. The special built-in green functions provide high efficiency at all power levels. This applies to quasi-resonant operation at high power levels, quasi-resonant operation with valley skipping, as well as to reduced frequency operation at lower power levels. At low power levels, the PFC switches over to burst mode control to maintain high efficiency. In burst mode, soft-start and soft-stop functions are added to eliminate audible noise. During low power conditions, the flyback controller switches to frequency reduction mode and limits the peak current to 25 % of its maximum value. This will ensure high efficiency at low power and good standby power performance while minimizing audible noise from the transformer. The proprietary high voltage BCD800 process makes direct start-up possible from the rectified universal mains voltage in an effective and green way. A second low voltage Silicon On Insulator (SOI) IC is used for accurate, high speed protection functions and control. The TEA1750 enables highly efficient and reliable supplies with power requirements up to 250 W, to be designed easily and with the minimum number of external components.
2. Features
2.1 Distinctive features
I Integrated PFC and flyback controller I Universal mains supply operation (70 V AC to 276 V AC) I High level of integration, resulting in a very low external component count and a cost-effective design
2.2 Green features
I On-chip start-up current source
2.3 PFC green features
I Valley/zero voltage switching for minimum switching losses (patented) I Frequency limitation to reduce switching losses I Burst mode operation if a low load is detected at the flyback output (patented)
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
2.4 Flyback green features
I Valley switching for minimum switching losses (patented) I Frequency reduction with fixed minimum peak current at low power operation to maintain high efficiency at low output power levels
2.5 Protection features
I Safe restart mode for system fault conditions I Continuous mode protection by means of demagnetization detection for both converters (patented) I UnderVoltage Protection (UVP) (foldback during overload) I Accurate OverVoltage Protection (OVP) for both converters (adjustable for flyback converter) I Open control loop protection for both converters I IC OverTemperature Protection (OTP) I Low and adjustable OverCurrent Protection (OCP) trip level for both converters I Soft (re)start for both converters I Soft stop PFC to minimize audible noise I Mains UnderVoltage Protection (UVP)/ brownout protection I General purpose input for latched protection, e.g. to be used for system Overtemperature protection
3. Applications
I The device can be used in all applications that require an efficient and cost-effective power supply solution up to 250 W. Notebook adapters in particular can benefit from the high level of integration.
4. Ordering information
Table 1. Ordering information Package Name TEA1750T SO16 Description plastic small outline package; 16 leads; body width 3.9 mm Version SOT109-1 Type number
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
2 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
5. Block diagram
PFCDRIVER PFC DRIVER
1.12 V 3.5 V
FBDRIVER 13 FB DRIVER DRV FB GATE EXT PROT
1.25 V 80 A
12 DRV
PFC GATE
5
LATCH
LOW VIN 7 LATCH RESET 6
1.25 V 3.7 V
VINSENSE
MAX
PFCCOMP
PFC PROT PROT ENABLE PFC
PROT R Q S Q S R ENABLEFB FREQ RED. LOW POWER TIME OUT 2.5 V 3.5 V
30 A
3 FBCTRL
VOSENSE
9
2.50 V
2.7 V
LOWVIN PFC PROT
PFC OSC VCC GOOD VoSTART FB LOW POWER EXT PROT EXT PROT OTP OvpFB LATCH RESET TON MAX VoSHORT TIMEOUT VUVLO PROT EXT PROT VSTART VUVLO
TON MAX SMPS CONTROL S S LATCHED S PROTECTION R S SAFE S RESTART S PROTECTION R
PFC OSC
VoOVP VoBURST HIGH VoBURST LOW VoSTART FB VoSHORT
STARTFB START STOP PFC
FB DRIVER
BLANK
10 PROT ENABLE FB START FB VCC GOOD START SOFT
FBSENSE
60 A
OCP BLANK PFC DRIVER ENABLE PFC SOFT START SOFT STOP START STOP PFC VoBURST LOW VoBURST HIGH TIMER 4 s 8 VALLEY DETECT PFCGATE ZCS
PFCSENSE
11
500 mV 60 A
CHARGE CONTROL CHARGE VALLEY DETECT OvpFB COUNTER 4 FB GATE FBAUX
OVP INTERNAL SUPPLY VSTART ZCS TEMP
PFCAUX
OTP CHANGE
TIMER 50 s
-100 mV
VUVLO 16 HV 1 VCC
OTP 2 GND
80 mV
014aaa055
Fig 1.
Block diagram
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
3 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
6. Pinning information
6.1 Pinning
VCC GND FBCTRL FBAUX LATCH PFCCOMP VINSENSE PFCAUX
1 2 3 4 5 6 7 8
014aaa015
16 HV 15 HVS 14 HVS 13 FBDRIVER 12 PFCDRIVER 11 PFCSENSE 10 FBSENSE 9 VOSENSE
TEA1750T
Fig 2.
Pin configuration for TEA1750T (SOT109-1)
6.2 Pin description
Table 2. Symbol VCC GND FBCTRL FBAUX LATCH PFCCOMP VINSENSE PFCAUX VOSENSE FBSENSE PFCSENSE PFCDRIVER FBDRIVER HVS HV Pin description Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14, 15 16 Description supply voltage ground control input for flyback input from auxiliary winding for demagnetization timing and overvoltage protection for flyback general purpose protection input frequency compensation pin for PFC sense input for mains voltage input from auxiliary winding for demagnetization timing for PFC sense input for PFC output voltage programmable current sense input for flyback programmable current sense input for PFC gate driver output for PFC gate driver output for flyback high voltage safety spacer, not connected high voltage start-up and valley sensing of flyback part
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
4 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
7. Functional description
7.1 General control
The TEA1750 contains a controller for a power factor correction circuit as well as a controller for a flyback circuit. A typical configuration is shown in Figure 3.
12 8 6
11
9
16 13 10
TEA1750T
7 3 2 4 1
014aaa016
Fig 3.
Typical configuration of TEA1750
7.1.1 Start-up and undervoltage lock-out
Initially the capacitor on the VCC pin is charged from the high voltage mains via the HV pin. As long as VCC is below Vtrip, the charge current is low. This protects the IC in case the VCC pin is shorted to ground. For a short start-up time the charge current above Vtrip is increased until VCC reaches Vth(UVLO). If VCC is between Vth(UVLO) and Vstartup, the charge current is low again, ensuring a low duty cycle during fault conditions. The control logic activates the internal circuitry and switches off the charge current when the voltage on pin VCC passes the Vstartup level. First, the LATCH pin output is activated and the soft-start capacitors on the PFCSENSE and FBSENSE pins are charged. When the LATCH pin voltage exceeds the Ven(LATCH) voltage and the soft-start capacitor on the PFCSENSE pin is charged, the PFC circuit is activated. The supply current from the HV pin is then switched on again and the PFC circuit charges the Cbus capacitor. When the voltage on pin VOSENSE reaches the Vstart(fb) level, the charge current is switched off and the flyback converter is activated (providing the soft-start capacitor on the FBSENSE pin is charged). The output voltage of the flyback converter is then regulated to its nominal output voltage. The IC supply is taken over by the auxiliary winding of the flyback converter. See Figure 4.
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
5 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
When the PFC is started, there is initially no supply take-over from the auxiliary winding. To make a small VCC capacitor possible, the VCC voltage is regulated to the Vstartup level, as long as the flyback converter has not yet started. Regulation is done by hysteretic control with a limited (high level) charge current. The hysteresis is typically 300 mV. If during start-up the LATCH pin does not reach the Ven(LATCH) level before VCC reaches Vth(UVLO), the LATCH pin output is de-activated and the charge current is switched on again. As soon as the flyback converter is started, the voltage on the FBCTRL pin is monitored. If the output voltage of the flyback converter does not reach its intended regulation level in a predefined time, the voltage on the FBCTRL pin reaches the Vto(FBCTRL) level and an error is assumed. The TEA1750 then initiates a safe restart. When one of the protection functions is activated, both converters stop switching and the VCC voltage drops to Vth(UVLO). A latched protection recharges the VCC capacitor via the HV pin, but does not restart the converters. For a safe-restart protection, the capacitor is recharged via the HV pin and the device restarts (see Figure 1) In the event of an overvoltage protection of the PFC circuit (VI on pin VOSENSE > Vovp(VOSENSE)), only the PFC controller stops switching until the VOSENSE pin voltage drops below Vovp(VOSENSE) again. Also, if a mains undervoltage is detected (VI on pin VINSENSE < Vstop(VINSENSE)), only the PFC controller stops switching until VI on pin VINSENSE > Vstart(VINSENSE) again. When the voltage on pin VCC drops below the undervoltage lock-out level, both controllers stop switching and re-enter the safe restart mode. In the safe restart mode the driver outputs are disabled and the VCC pin voltage is recharged via the HV pin.
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
6 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
IHV Vstartup VCC Vth(UVLO) Vtrip
Vstart(VINSENSE) VINSENSE
LATCH PROTECTION
Ven(LATCH)
soft start
PFCSENSE
PFCDRIVER
soft start
FBSENSE
FBDRIVER Vto(FBCTRL) FBCTRL
Vstart(fb) VOSENSE Vout CHARGING VCC STARTING NORMAL PROTECTION CAPACITOR CONVERTERS OPERATION RESTART
014aaa060
Fig 4.
Start-up sequence, normal operation, and re-start sequence
7.1.2 Supply management
All internal reference voltages are derived from a temperature compensated and trimmed on-chip band gap circuit. Internal reference currents are derived from a temperature compensated and trimmed on-chip current reference circuit.
7.1.3 Latch input
Pin LATCH is a general purpose input pin, which can be used to switch off both converters. The pin sources a current, IO(LATCH) on pin LATCH (typ 80 A). Switching of both converters is stopped as soon as the voltage on this pin drops below 1.25 V. At initial start-up, switching is inhibited until the voltage on the LATCH pin is above 1.35 V (typ). No internal filtering is done on this pin. An internal Zener clamp of 2.7 V (typ) protects this pin from excessive voltages.
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
7 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
7.1.4 Fast latch reset
In a typical application, the mains can be interrupted briefly to reset the latched protection. The PFC bus capacitor, Cbus, does not have to discharge for this latched protection to reset. Typically the PFC bus capacitor, Cbus, has to discharge for the VCC to drop to this reset level. When the latched protection is set, the clamping circuit of the VINSENSE circuit is disabled (see also Section 7.2.8). As soon as the VINSENSE voltage drops below 750 mV (typ) and then is raised to 870 mV (typ), the latched protection is reset. The latched protection will also be reset by removing both the voltage on pin VCC and on pin HV.
7.1.5 Overtemperature protection (OTP)
An accurate internal temperature protection is provided in the circuit. When the junction temperature exceeds the thermal shutdown temperature, the IC only stops switching. As long as OTP is active, the VCC capacitor is not recharged from the HV mains. The OTP circuit is supplied from the HV pin if the VCC supply voltage is not sufficient. OTP is a latched protection. It can be reset by removing both the voltage on pin VCC and on pin HV or by the fast latch reset function, see Section 7.1.4
7.2 Power factor correction circuit
The power factor correction circuit operates in quasi-resonant or discontinuous conduction mode with valley switching. The next primary stroke is only started when the previous secondary stroke has ended and the voltage across the PFC MOSFET has reached a minimum value. The voltage on the PFCAUX pin is used to detect transformer demagnetization and the minimum voltage across the external PFC MOSFET switch.
7.2.1 ton control
The power factor correction circuit is operated in ton control. The resulting mains harmonic reduction of a typical application is well within the class-D requirements.
7.2.2 Valley switching and demagnetization (PFCAUX pin)
The PFC MOSFET is switched on after the transformer is demagnetized. Internal circuitry connected to the PFCAUX pin detects the end of the secondary stroke. It also detects the voltage across the PFC MOSFET. The next stroke is started if the voltage across the PFC MOSFET is at its minimum in order to reduce switching losses and electromagnetic interference (EMI) (valley switching). If no demagnetization signal is detected on the PFCAUX pin, the controller generates a zero current signal (ZCS), 50 s (typ) after the last PFC gate signal. If no valley signal is detected on the PFCAUX pin, the controller generates a valley signal 4 s (typ) after demagnetization was detected. To protect the internal circuitry, for example during lightning events, it is advisable to add a 5 k series resistor to this pin. To prevent incorrect switching due to external disturbance, the resistor should be placed close to the IC on the printed circuit board.
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
8 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
For applications with high transformer ringing frequencies (after the secondary stroke), the PFCAUX pin should be connected via a capacitor and a resistor to the auxiliary winding. A diode must than be placed from the ground connection to the PFCAUX pin.
7.2.3 Frequency limitation
To optimize the transformer and minimize switching losses, the switching frequency is limited to fsw(PFC)max. If the frequency for quasi-resonant operation is above the fsw(PFC)max limit, the system switches over to discontinuous conduction mode. Also here, the PFC MOSFET is only switched on at a minimum voltage across the switch (valley switching).
7.2.4 Mains voltage compensation (VINSENSE pin)
The mathematical equation for the transfer function of a power factor corrector contains the square of the mains input voltage. In a typical application this results in a low bandwidth for low mains input voltages, while at high mains input voltages the Mains Harmonic Reduction (MHR) requirements may be hard to meet. To compensate for the mains input voltage influence, the TEA1750 contains a correction circuit. Via the VINSENSE pin the average input voltage is measured and the information is fed to an internal compensation circuit. With this compensation it is possible to keep the regulation loop bandwidth constant over the full mains input range, yielding a fast transient response on load steps, while still complying with class-D MHR requirements. In a typical application, the bandwidth of the regulation loop is set by a resistor and two capacitors on the PFCCOMP pin.
7.2.5 Soft start-up (pin PFCSENSE)
To prevent audible transformer noise at start-up or during hiccup, the transformer peak current, IDM, is increased slowly by the soft start function. This can be achieved by inserting RSS1 and CSS1 between pin PFCSENSE and current sense resistor, RSENSE1. An internal current source charges the capacitor to VPFCSENSE = Istart(soft)PFC x RSS1. The voltage is limited to Vstart(soft)PFC. The start level and the time constant of the increasing primary current level can be adjusted externally by changing the values of RSS1 and CSS1. SoftStart = 3 x R SS1 x C SS1 The charging current Istart(soft)PFC flows as long as the voltage on pin PFCSENSE is below 0.5 V (typ). If the voltage on pin PFCSENSE exceeds 0.5 V, the soft start current source starts limiting current Istart(soft)PFC. As soon as the PFC starts switching, the Istart(soft)PFC current source is switched off; see Figure 5.
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
9 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
S1
Istart(soft)PFC 60 A
SOFT START SOFT STOP CONTROL
RSS1
11 PFCSENSE
+ 0.5 V
OCP
CSS1 RSENSE1
014aaa018
Fig 5.
Soft start-up and soft stop of PFC
7.2.6 Burst mode control
When the output power of the flyback converter (see Section 7.3) is low, the flyback converter switches over to frequency reduction mode. When frequency reduction mode is entered by the flyback controller, the power factor correction circuit switches to burst mode control. In burst mode control, switching of the power factor correction circuit is inhibited until the voltage on the VOSENSE pin has dropped to Vburst(L). Switching then restarts with a soft-start to avoid audible noise (see Section 7.2.5). As soon as the voltage on the VOSENSE pin reaches Vburst(H) the soft-stop circuit is activated, again to avoid audible noise. During the soft-stop time the output voltage of the power factor correction circuit overshoots, depending on the soft-start resistor and capacitor, RSS1 and CSS1, on the PFCSENSE pin. As the Vburst(H) voltage is well below the Vreg(VOSENSE) voltage, the PFC output voltage does not reach the normal operation output voltage of the power factor correction circuit in a typical application due to this overshoot. The burst mode repetition rate is defined by the output power and the value of the bus capacitor, Cbus. During burst mode operation the PFCCOMP pin is clamped between a voltage of 2.7 V (typ) and 3.9 V (typ). The lower clamp voltage limits the maximum power that is delivered during burst mode operation and yields a more sinusoidal input current during the burst pulse. The upper clamp voltage ensures that the PFC can return to its normal regulation point in a limited amount of time when returning from burst mode. As soon as the flyback converter leaves frequency reduction mode, the power factor correction circuit restores normal operation. To prevent continuous on and off switching of the PFC circuit, a small hysteresis is built in (50 mV (typ) on the FBCTRL pin).
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
10 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
Vburst(H)
VVOSENSE
Vburst(L)
envelop of peak current
soft-start
ton control
soft-stop
014aaa019
Fig 6.
Burst mode control
7.2.7 Overcurrent protection (PFCSENSE pin)
The maximum peak current is limited cycle-by-cycle by sensing the voltage across an external sense resistor (RSENSE1) on the source of the external MOSFET. The voltage is measured via the PFCSENSE pin.
7.2.8 Mains undervoltage lock-out / brownout protection (VINSENSE pin)
To prevent the PFC from operating at very low mains input voltages, the voltage on the VINSENSE pin is sensed continuously. As soon as the voltage on this pin drops below the Vstop(VINSENSE) level, switching of the PFC is stopped. If the low mains situation continues, the PFC bus voltage eventually drops. The voltage on the VOSENSE pin then drops below the Vstart(fb) level and the flyback converter is also disabled. The voltage on pin VINSENSE is clamped to a minimum value, (Vstart(VINSENSE) - Vpu(VINSENSE)) for a fast restart as soon as the mains input voltage is restored after a mains dropout.
7.2.9 Overvoltage protection (VOSENSE pin)
To prevent output overvoltage during load steps and mains transients, an overvoltage protection circuit is built in. As soon as the voltage on the VOSENSE pin exceeds the Vovp(VOSENSE) level, switching of the power factor correction circuit is inhibited. Switching of the PFC recommences as soon as the VOSENSE pin voltage drops below the Vovp(VOSENSE) level again. When the resistor between pin VOSENSE and ground is open, the overvoltage protection is also triggered.
7.2.10 PFC open loop protection (VOSENSE pin)
The power factor correction circuit does not start switching until the voltage on the VOSENSE pin is above the Vth(ol)(VOSENSE) level. This protects the circuit from open loop and VOSENSE short situations. As the VOSENSE pin draws a small input current, switching is also inhibited when the pin is left open.
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
11 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
7.2.11 Driver (pin PFCDRIVER)
The driver circuit to the gate of the power MOSFET has a current sourcing capability of typically 500 mA and a current sink capability of typically 1.2 A. This permits fast turn-on and turn-off of the power MOSFET for efficient operation.
7.3 Flyback controller
The TEA1750 includes a controller for a flyback converter. The flyback converter operates in quasi-resonant or discontinuous conduction mode with valley switching. The auxiliary winding of the flyback transformer provides demagnetization detection and powers the IC after start-up.
7.3.1 Multi mode operation
The TEA1750 flyback controller can operate in multi modes; see Figure 7.
fsw(fb)max
PFC burst mode
PFC on
frequency reduction
switching frequency
discontinuous with valley switching
quasi resonant
output power
014aaa025
Fig 7.
Multi mode operation flyback
At high output power the converter switches to quasi-resonant mode. The next converter stroke is started after demagnetization of the transformer current. In quasi-resonant mode switching losses are minimized as the converter only switches on when the voltage across the external MOSFET is at its minimum (valley switching, see also Section 7.3.2). To prevent high frequency operation at lower loads, the quasi-resonant operation changes to discontinuous mode operation with valley skipping in which the switching frequency is limited for EMI to fsw(fb)(max) (125 kHz typ). Again, the external MOSFET is only switched on when the voltage across the MOSFET is at its minimum. At very low power and standby levels the frequency is controlled down by a voltage controlled oscillator (VCO). The minimum frequency can be reduced to zero. During frequency reduction mode, the primary peak current is kept at a minimal level of Ipkmax/4 to maintain a high efficiency. (Ipkmax is the maximum primary peak current set by the sense resistor and the maximum sense voltage.) As the primary peak current is low in frequency reduction mode operation (Ipk = Ipkmax/4), no audible noise is noticeable at switching frequencies in the audible range. Valley switching is also active in this mode.
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
12 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
In frequency reduction mode the PFC controller is switched to burst mode operation and the flyback maximum frequency changes linearly with the control voltage on the FBCTRL pin (see Figure 8 ). For stable on-off switching of the PFC burst mode, the FBCTRL pin has a 50 mV (typ) hysteresis. At no load operation the switching frequency of the flyback can be reduced to (almost) zero.
fsw(fb)max
PFC burst mode
PFC on
frequency reduction
switching frequency
discontinuous with valley switching
quasi resonant
1.5 V
VFBCTRL
014aaa026
Fig 8.
Frequency control of flyback part
7.3.2 Valley switching (HV pin)
Refer to Figure 9. A new cycle starts when the external MOSFET is activated. After the on-time (determined by the FBSENSE voltage and the FBCTRL voltage), the MOSFET is switched off and the secondary stroke starts. After the secondary stroke, the drain voltage 1 shows an oscillation with a frequency of approximately --------------------------------------------------(2 x x ( L p x Cd )) where Lp is the primary self inductance of the flyback transformer and Cd is the capacitance on the drain node. As soon as the internal oscillator voltage is high again and the secondary stroke has ended, the circuit waits for the lowest drain voltage before starting a new primary stroke. Figure 9 shows the drain voltage, valley signal, secondary stroke signal and the internal oscillator signal. Valley switching allows high frequency operation as capacitive switching losses are reduced, see Equation 1. High frequency operation makes small and cost-effective magnetics possible. P = 1 x C x V 2 x f -d 2 (1)
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
13 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
primary stroke
secondary stroke
secondary ringing
drain
valley
secondary stroke
(2)
(1)
oscillator
014aaa027
(1) Start of new cycle at lowest drain voltage. (2) Start of new cycle in a classical Pulse Width Modulation (PWM) system without valley detection.
Fig 9.
Signals for valley switching
7.3.3 Current mode control (FBSENSE pin)
Current mode control is used for the flyback converter for its good line regulation. The primary current is sensed by the FBSENSE pin across an external resistor and compared with an internal control voltage.The internal control voltage is proportional to the FBCTRL pin voltage.
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
14 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
Vsense(fb)max 0.52 V PFC burst mode flyback frequency reduction flyback discontinuous or QR flyback cycle skip mode 0.13 V PFC on
FBSENSE peak voltage
1.4 V 1.5 V
2.0 V
VFBCTRL
014aaa028
Fig 10. Frequency control of flyback part
The driver output is latched in the logic, preventing multiple switch-on.
7.3.4 Demagnetization (FBAUX pin)
The system is always in quasi-resonant or discontinuous conduction mode. The internal oscillator does not start a new primary stroke until the previous secondary stroke has ended. Demagnetization features a cycle-by-cycle output short-circuit protection by immediately lowering the frequency (longer off-time), thereby reducing the power level. Demagnetization recognition is suppressed during the first tsup(xfmr_ring) time (2 s typ). This suppression may be necessary at low output voltages and at start-up and in applications where the transformer has a large leakage inductance. If pin FBAUX is open-circuit or not connected, a fault condition is assumed and the converter stops operating immediately. Operation restarts as soon as the fault condition is removed.
7.3.5 Flyback control / time-out (FBCTRL pin)
The pin FBCTRL is connected to an internal voltage source of 3.5 V via an internal resistor (typical resistance is 3 k). As soon as the voltage on this pin is above 2.5 V (typ), this connection is disabled. Above 2.5 V the pin is biased with a small current. When the voltage on this pin rises above 4.5 V (typ), a fault is assumed and switching is inhibited. When a small capacitor is connected to this pin, a time-out function can be created to protect against an open control loop situation (see Figure 11 and Figure 12). The time-out function can be disabled by connecting a resistor (100 k) to ground on the FBCTRL pin. If the pin is shorted to ground, switching of the flyback controller is inhibited. In normal operating conditions, when the converter is regulating the output voltage, the voltage on the FBCTRL pin is between 1.4 V and 2.0 V (typical values) from minimum to maximum output power.
TEA1750_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
15 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
2.5 V
3.5 V
30 A
4.5 V
3 k
TIMEOUT
FBCTRL
014aaa049
a. Circuit diagram
4.5 V 2.5 V
VFBCTRL
output voltage intended output voltage not reached within time-out time. restart intended output voltage reached within time-out time.
014aaa050
b. Timing diagram Fig 11. Time-out protection
7.3.6 Soft start-up (pin FBSENSE)
To prevent audible transformer noise during start-up, the transformer peak current, IDM is slowly increased by the soft start function. This can be achieved by inserting a resistor and a capacitor between pin FBSENSE and the current sense resistor. An internal current source charges the capacitor to V = Istart(soft)(fb) x RSS2, with a maximum of approximately 0.5 V. The start level and the time constant of the increasing primary current level can be adjusted externally by changing the values of RSS2 and CSS2. SoftStart = 3 x R SS2 x C SS2 The soft start current Istart(soft)(fb) is switched on as soon as VCC reaches Vstartup. When the voltage on the VOSENSE pin reaches the Vstart(fb) level and the voltage on pin FBSENSE has reached 0.5 V, the flyback converter starts switching. The soft start current flows as long as the voltage on pin FBSENSE is below approximately 0.5 V. If the voltage on pin FBSENSE exceeds 0.5 V, the soft start current source starts limiting the current. After the flyback converter has started, the soft start current source is switched off.
TEA1750_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
16 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
S2
Istart(soft)fb 60 A
SOFT START CONTROL
RSS2
10 FBSENSE
+ 0.5 V
OCP
CSS2 RSENSE2
014aaa020
Fig 12. Soft start-up of flyback
7.3.7 Maximum on-time
The flyback controller limits the `on-time' of the external MOSFET to 25 s (typ). When the `on-time' is longer than 25 s, the IC stops switching and enters the safe restart mode.
7.3.8 Overvoltage protection (FBAUX pin)
An output overvoltage protection is implemented in the GreenChip III series. This works for the TEA1750 by sensing the auxiliary voltage via the current flowing into pin FBAUX during the secondary stroke. The auxiliary winding voltage is a well-defined replica of the output voltage. Voltage spikes are averaged by an internal filter. If the output voltage exceeds the OVP trip level, an internal counter starts counting subsequent OVP events. The counter has been added to prevent incorrect OVP detection which might occur during ElectroStatic Discharge (ESD) or lightning events. If the output voltage exceeds the OVP trip level a few times and not again in a subsequent cycle, the internal counter counts down at twice the speed it uses when counting up. However, when typically 8 cycles of subsequent OVP events are detected, the IC assumes a true OVP and the OVP circuit switches the power MOSFET off. As the protection is latched, the converter only restarts after the internal latch is reset. In a typical application the mains should be interrupted to reset the internal latch. The output voltage Vovp(FBAUX) at which the OVP function trips, can be set by the demagnetization resistor, RFBAUX : Ns V o ( ovp ) = ----------- ( I ovp ( FBAUX ) x R FBAUX + V clamp ( FBAUX ) ) N aux where Ns is the number of secondary turns and Naux is the number of auxiliary turns of the transformer. Current Iovp(FBAUX) is internally trimmed. The value of RFBAUX can be adjusted to the turns ratio of the transformer, thus making an accurate OVP detection possible.
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
17 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
7.3.9 Overcurrent protection (FBSENSE pin)
The primary peak current in the transformer is measured accurately cycle-by-cycle using the external sense resistor RSENSE2. The OCP circuit limits the voltage on pin FBSENSE to an internal level (see also Section 7.3.3). The OCP detection is suppressed during the leading edge blanking period, tleb, to prevent false triggering caused by switch-on spikes.
LEB (tleb) OCP LEVEL
VFBSENSE t
014aaa022
Fig 13. OCP leading edge blanking
7.3.10 Driver (pin FBDRIVER)
The driver circuit to the gate of the external power MOSFET has a current sourcing capability of typically 500 mA and a current sink capability of typically 1.2 A. This permits fast turn-on and turn-off of the power MOSFET for efficient operation.
8. Limiting values
Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Voltages VCC VLATCH VFBCTRL VPFCCOMP VVINSENSE VVOSENSE VPFCAUX VFBSENSE VHV Currents IFBCTRL IFBAUX IPFCSENSE IFBSENSE IFBDRIVER IHV
TEA1750_2
Parameter supply voltage voltage on pin LATCH voltage on pin FBCTRL voltage on pin PFCCOMP voltage on pin VINSENSE voltage on pin VOSENSE voltage on pin PFCAUX voltage on pin FBSENSE voltage on pin HV current on pin FBCTRL current on pin FBAUX current on pin PFCSENSE current on pin FBSENSE current on pin FBDRIVER current on pin HV
Conditions
Min -0.4
Max +38 +5 +5 +5 +5 +5 +25 +5 +5 +650 0 +1 +10 +10 +2 +2 5
Unit V V V V V V V V V V mA mA mA mA A A mA
current limited
-0.4 -0.4 -0.4 -0.4 -0.4 -25
current limited current limited
-0.4 -0.4 -0.4 -3 -1 -1 -1
VPFCSENSE voltage on pin PFCSENSE
duty cycle < 10 % duty cycle < 10 %
-0.8 -0.8 -
IPFCDRIVER current on pin PFCDRIVER
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
18 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
Table 3. Limiting values ...continued In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol General Ptot Tstg Tj ESD VESD electrostatic discharge voltage human body model machine model charged device model
[1] [2]
Parameter total power dissipation storage temperature junction temperature
Conditions Tamb < 75 C
Min -55 -40
Max 0.6 +150 +150
Unit W C C
class 1 pins 1 to 13 pin 16 (HV)
[1] [1] [2]
-
2000 1500 200 500
V V V V
Equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor. Equivalent to discharging a 200 pF capacitor through a 0.75 H coil and a 10 resistor.
9. Thermal characteristics
Table 4. Symbol Rth(j-a) Thermal characteristics Parameter thermal resistance from junction to ambient Conditions in free air; JEDEC test board Typ 124 Unit K/W
10. Characteristics
Table 5. Characteristics Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol IHV Parameter current on pin HV Conditions VHV > 80 V; VCC < Vtrip; Vth(UVLO) < VCC < Vstartup Vtrip < VCC < Vth(UVLO) with auxiliary supply VBR Vtrip Vstartup Vth(UVLO) Vstart(hys) Vhys breakdown voltage trip voltage start-up voltage undervoltage lockout threshold voltage hysteresis of start voltage hysteresis voltage during start-up phase Vstartup - Vth(UVLO) Supply voltage management (pin VCC) 0.55 21 14 6.3 0.65 22 15 300 7 0.75 23 16 7.7 V V V mV V 8 650 1 5.4 20 40 mA mA A V Min Typ Max Unit Start-up current source (pin HV)
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
19 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
Table 5. Characteristics ...continued Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol Ich(low) Ich(high) ICC(oper) Parameter low charging current high charging current operating supply current Conditions VI on pin HV > 80 V; VCC < Vtrip or Vth(UVLO) < VCC < Vstartup VI on pin HV > 80 V; Vtrip < VCC < Vth(UVLO) no load on pin FBDRIVER and PFCDRIVER Min -1.2 -6.3 2.25 Typ -1 -5.4 3 Max -0.8 -4.6 3.75 Unit mA mA mA
Input voltage sensing PFC (pin VINSENSE) Vstop(VINSENSE) Vstart(VINSENSE) Vpu(VINSENSE) Ipu(VINSENSE) Vmvc(VINSENSE)max stop voltage on pin VINSENSE start voltage on pin VINSENSE pull-up voltage difference on pin VINSENSE pull-up current on pin VINSENSE maximum mains voltage compensation voltage on pin VINSENSE fast latch reset voltage hysteresis of fast latch reset voltage input current on pin VINSENSE transconductance output current on pin PFCCOMP clamp voltage on pin PFCCOMP zero on-time voltage on pin PFCCOMP maximum on-time voltage on pin PFCCOMP PFC on-time VVINSENSE = 3.3 V; VPFCCOMP = Vton(max)(PFC) VVINSENSE = 0.9 V; VPFCCOMP = Vton(max)(PFC) VVINSENSE > Vstop(VINSENSE) after Vstart(VINSENSE) is detected VVOSENSE to IO(PFCCOMP) VVOSENSE = 3.3 V VVOSENSE = 2.0 V low power mode, PFC in burst mode, lower clamp voltage upper clamp voltage Vton(PFCCOMP)zero Vton(PFCCOMP)max
[1]
0.86 1.11 active after Vstop(VINSENSE) is detected active after Vstop(VINSENSE) is detected -55 4.0
0.89 1.15 -100 -47 -
0.92 1.19 -40 -
V V mV A V
Vflr Vflr(hys) II(VINSENSE)
active after Vth(UVLO) is detected
5
0.75 0.12 33
100
V V nA
Loop compensation PFC(pin PFCCOMP) gm IO(PFCCOMP) Vclamp(PFCCOMP) 60 33 -45 2.5 3.4 1.20 80 39 -39 2.7 3.9 3.5 1.25 100 45 -33 2.9 3.6 1.30 A/V A A V V V V
[1]
Pulse width modulator PFC ton(PFC) 3.6 30 4.5 40 5.0 53 s s
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
20 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
Table 5. Characteristics ...continued Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol Vth(ol)(VOSENSE) Vstart(fb) Vstop(fb) Vburst(L) Vburst(H) Vreg(VOSENSE) Vovp(VOSENSE) II(VOSENSE) Parameter open-loop threshold voltage on pin VOSENSE flyback start voltage flyback stop voltage LOW-level burst mode voltage HIGH-level burst mode voltage regulation voltage on pin VOSENSE overvoltage protection voltage on pin VOSENSE input current on pin VOSENSE maximum PFC sense voltage PFC leading edge blanking time protection current on pin PFCSENSE PFC soft start current PFC soft start voltage PFC soft stop voltage PFC soft start resistance maximum PFC switching frequency minimum PFC off-time PFC valley recognition voltage change with time PFC valley recognition time PFC valley recognition time-out time VPFCAUX = 1 V; peak-to-peak demagnetization to V/t = 0 tto(vrec)PFC
[3] [4] [2]
Conditions
Min 0.35 1.55 1.87 2.19
Typ 0.40 1.72 1.60 1.92 2.24
Max 0.45 1.65 1.97 2.29
Unit V V V V V
Output voltage sensing PFC (pin VOSENSE)
IO(PFCCOMP) = 0
2.475 2.500 2.525 V 2.60 2.63 45 2.67 100 V nA
VVOSENSE = 2.5 V
5
Overcurrent protection PFC (pin PFCSENSE) Vsense(PFC)max tleb(PFC) Iprot(PFCSENSE) V/t = 50 mV/s V/t = 200 mV/s 0.49 0.51 250 -50 0.52 0.54 310 0.55 0.57 370 -5 V V ns nA
Soft start, soft stop PFC (pin PFCSENSE) Istart(soft)PFC Vstart(soft)PFC Vstop(soft)PFC Rstart(soft)PFC Oscillator PFC fsw(PFC)max toff(PFC)min (V/t)vrec(PFC) tvrec(PFC) 100 1.1 3 125 1.4 4 150 1.7 1.7 300 50 6 kHz s V/s ns ns s -75 0.46 0.42 12 -60 0.50 0.45 -45 0.54 0.48 A V V k
Valley switching PFC (pin PFCAUX)
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
21 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
Table 5. Characteristics ...continued Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol Vth(comp)PFCAUX tto(demag)PFC Iprot(PFCAUX) Parameter comparator threshold voltage on pin PFCAUX PFC demagnetization time-out time protection current on pin PFCAUX source current on pin PFCDRIVER sink current on pin PFCDRIVER maximum output voltage on pin PFCDRIVER overvoltage protection current on pin FBAUX number of overvoltage protection cycles comparator threshold voltage on pin FBAUX protection current on pin FBAUX clamp voltage on pin FBAUX transformer ringing suppression time minimum flyback on-time maximum flyback on-time maximum flyback switching frequency VCO start voltage on pin FBCTRL hysteresis voltage on pin FBCTRL VCO voltage difference on pin FBCTRL VFBAUX = 50 mV IFBAUX = -500 A IFBAUX = 500 A tsup(xfmr_ring) VPFCAUX = 50 mV Conditions Min -150 40 -75 Typ -100 50 Max -50 60 -5 Unit mV s nA Demagnetization management PFC (pin PFCAUX)
Driver (pin PFCDRIVER) Isrc(PFCDRIVER) Isink(PFCDRIVER) VO(PFCDRIVER)max VPFCDRIVER = 2 V VPFCDRIVER = 2 V VPFCDRIVER = 10 V -0.5 0.7 1.2 11 12 A A A V
Overvoltage protection flyback (pin FBAUX) Iovp(FBAUX) Ncy(ovp) 279 6 300 8 321 12 A
Demagnetization management flyback (pin FBAUX) Vth(comp)FBAUX Iprot(FBAUX) Vclamp(FBAUX) 60 -50 -1.0 0.5 1.5 80 -0.8 0.7 2 110 -5 -0.6 0.9 2.5 mV nA V V s
Pulse width modulator flyback ton(fb)min ton(fb)max Oscillator flyback fsw(fb)max Vstart(VCO)FBCTRL Vhys(FBCTRL) VVCO(FBCTRL) 100 1.3 125 1.5 60 -0.1 150 1.7 kHz V mV V 20 tleb(fb) 25 30 ns s
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
22 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
Table 5. Characteristics ...continued Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol VFBCTRL Vto(FBCTRL) Rint(FBCTRL) IO(FBCTRL) Ito(FBCTRL) Parameter voltage on pin FBCTRL time-out voltage on pin FBCTRL internal resistance on pin FBCTRL output current on pin FBCTRL VFBCTRL = 0 V VFBCTRL = 2 V time-out current on pin FBCTRL VFBCTRL = 2.6 V VFBCTRL = 4.1 V Valley switching flyback (pin HV) (V/t)vrec(fb) td(vrec-swon) flyback valley recognition voltage change with time valley recognition to switch-on delay time flyback soft start current flyback soft start voltage flyback soft start resistance maximum flyback sense voltage flyback leading edge blanking time source current on pin FBDRIVER VFBDRIVER = 2 V V/t = 50 mV/s V/t = 200 mV/s
[5]
Conditions for maximum flyback peak current enable voltage trip voltage
Min 1.85 4.2 -1.4 -0.6 -36
Typ 2.0 2.5 4.5 3
Max 2.15 4.8 -
Unit V V V k
Peak current control flyback (pin FBCTRL)
-1.17 -0.93 mA -0.5 -30 -0.4 -24 mA A
-34.5 -28.5 -22.5 A -75 150 +75 V/s ns
Soft start flyback (pin FBSENSE) Istart(soft)fb Vstart(soft)fb Rstart(soft)fb Vsense(fb)max tleb(fb) -75 0.43 12 0.49 0.52 255 -60 0.49 0.52 0.55 305 -45 0.54 0.55 0.58 355 A V k V V ns
Overcurrent protection flyback (pin FBSENSE)
Driver (pin FBDRIVER) Isrc(FBDRIVER) Isink(FBDRIVER) VO(FBDRIVER)(max) -0.5 0.7 1.2 11 12 A A A V
sink current on pin FBDRIVER VFBDRIVER = 2 V VFBDRIVER = 10 V maximum output voltage on pin FBDRIVER protection voltage on pin LATCH output current on pin LATCH enable voltage on pin LATCH hysteresis voltage on pin LATCH open-circuit voltage on pin LATCH Vprot(LATCH) < VLATCH < Voc(LATCH) at start-up Ven(LATCH) - Vprot(LATCH)
Latch input (pin LATCH) Vprot(LATCH) IO(LATCH) Ven(LATCH) Vhys(LATCH) Voc(LATCH) 1.23 -85 1.30 80 1.25 -80 1.35 100 2.9 1.27 -75 1.40 140 V A V mV V
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
23 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
Table 5. Characteristics ...continued Tamb = 25 C; VCC = 20 V; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the IC; unless otherwise specified. Symbol Tpl(IC) Tpl(IC)hys Parameter IC protection level temperature hysteresis of IC protection level temperature Conditions Min 130 Typ 140 10 Max 150 Unit C C Temperature protection
[1] [2] [3] [4] [5]
For a typical application with a compensation network on pin PFCCOMP, like the example in Figure 3. Typically 120 mV above Vstop(fb). Minimum required voltage change time for valley recognition on pin PFCAUX. Minimum required time between demagnetization recognition and V/t end. Guaranteed by design.
11. Application information
A power supply with the TEA1750 consists of a power factor correction circuit followed by a flyback converter. See Figure 14. Capacitor CVCC buffers the IC supply voltage, which is powered via the high voltage rectified mains during start-up and via the auxiliary winding of the flyback converter during operation. Sense resistors RSENSE1 and RSENSE2 convert the current through the MOSFETs S1 and S2 into a voltage at pins PFCSENSE and FBSENSE. The values of RSENSE1 and RSENSE2 define the maximum primary peak current in MOSFETs S1 and S2. In the example given, the LATCH pin is connected to a Negative Temperature Coefficient V prot ( LATCH ) (NTC) resistor. When the resistance drops below -------------------------------- = 15.6 k (typ), the I O ( LATCH ) protection is activated. A capacitor CTIMEOUT is connected to the FBCTRL pin. For a 120 nF capacitor, typically after 10 ms the time-out protection is activated. RLOOP is added so that the time-out capacitor does not interfere with the normal regulation loop. RS1 and RS2 are added to prevent the soft-start capacitors from being charged during normal operation due to negative voltage spikes across the sense resistors. Resistor RAUX1 is added to protect the IC from damage during lightning events. For applications with high transformer ringing frequencies (after the secondary stroke), the PFCAUX pin should be connected via a capacitor and a resistor to the auxiliary winding. A diode must than be placed from the ground connection to the PFCAUX pin.
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
24 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
D1 Cbus
S1
CSS1
RSS1 T2 RSENSE1 D2 COUT S2 RS1
RAUX1
12 8
COMPENSATION
11
9 16 13 10
RS2
RSS2
6
TEA1750T
7 4 1 3 2 5
CSS2 RSENSE2
RAUX2
CVCC
RLOOP CTIMEOUT
014aaa021
Fig 14. Typical application diagram of TEA1750
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
25 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
12. Package outline
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
D
E
A X
c y HE vMA
Z 16 9
Q A2 pin 1 index Lp 1 e bp 8 wM L detail X A1 (A 3) A
0
2.5 scale
5 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 1.75 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 10.0 9.8 E (1) 4.0 3.8 0.16 0.15 e 1.27 0.05 HE 6.2 5.8 L 1.05 Lp 1.0 0.4 0.039 0.016 Q 0.7 0.6 0.028 0.020 v 0.25 0.01 w 0.25 0.01 y 0.1 Z (1) 0.7 0.3
0.010 0.057 0.069 0.004 0.049
0.019 0.0100 0.39 0.014 0.0075 0.38
0.244 0.041 0.228
0.028 0.004 0.012
8 o 0
o
Note 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. OUTLINE VERSION SOT109-1 REFERENCES IEC 076E07 JEDEC MS-012 JEITA EUROPEAN PROJECTION
ISSUE DATE 99-12-27 03-02-19
Fig 15. Package outline SOT109-1 (SO16)
TEA1750_2 (c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
26 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
13. Revision history
Table 6. Revision history Release date 20081215 20070406 Data sheet status Product data sheet Product data sheet Change notice Supersedes TEA1750_1 Document ID TEA1750_2 Modifications: TEA1750_1
Value for Tj in Table 3 has been updated
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
27 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
14. Legal information
14.1 Data sheet status
Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet
[1] [2] [3]
Product status[3] Development Qualification Production
Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification.
Please consult the most recently issued document before initiating or completing a design. The term `short data sheet' is explained in section "Definitions". The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
14.2 Definitions
Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
14.3 Disclaimers
General -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected
14.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. GreenChip -- is a trademark of NXP B.V.
15. Contact information
For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com
TEA1750_2
(c) NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 -- 15 December 2008
28 of 29
NXP Semiconductors
TEA1750
GreenChip III SMPS control IC
16. Contents
General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Distinctive features . . . . . . . . . . . . . . . . . . . . . . 1 Green features . . . . . . . . . . . . . . . . . . . . . . . . . 1 PFC green features . . . . . . . . . . . . . . . . . . . . . 1 Flyback green features . . . . . . . . . . . . . . . . . . . 2 Protection features . . . . . . . . . . . . . . . . . . . . . . 2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 General control . . . . . . . . . . . . . . . . . . . . . . . . . 5 Start-up and undervoltage lock-out . . . . . . . . . 5 Supply management. . . . . . . . . . . . . . . . . . . . . 7 Latch input . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Fast latch reset . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overtemperature protection (OTP) . . . . . . . . . . 8 Power factor correction circuit. . . . . . . . . . . . . . 8 ton control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Valley switching and demagnetization (PFCAUX pin) . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7.2.3 Frequency limitation . . . . . . . . . . . . . . . . . . . . . 9 7.2.4 Mains voltage compensation (VINSENSE pin). 9 7.2.5 Soft start-up (pin PFCSENSE) . . . . . . . . . . . . . 9 7.2.6 Burst mode control . . . . . . . . . . . . . . . . . . . . . 10 7.2.7 Overcurrent protection (PFCSENSE pin) . . . . 11 7.2.8 Mains undervoltage lock-out / brownout protection (VINSENSE pin). . . . . . . . . . . . . . . 11 7.2.9 Overvoltage protection (VOSENSE pin) . . . . . 11 7.2.10 PFC open loop protection (VOSENSE pin) . . 11 7.2.11 Driver (pin PFCDRIVER) . . . . . . . . . . . . . . . . 12 7.3 Flyback controller . . . . . . . . . . . . . . . . . . . . . . 12 7.3.1 Multi mode operation . . . . . . . . . . . . . . . . . . . 12 7.3.2 Valley switching (HV pin) . . . . . . . . . . . . . . . . 13 7.3.3 Current mode control (FBSENSE pin) . . . . . . 14 7.3.4 Demagnetization (FBAUX pin) . . . . . . . . . . . . 15 7.3.5 Flyback control / time-out (FBCTRL pin) . . . . 15 7.3.6 Soft start-up (pin FBSENSE) . . . . . . . . . . . . . 16 7.3.7 Maximum on-time . . . . . . . . . . . . . . . . . . . . . . 17 7.3.8 Overvoltage protection (FBAUX pin). . . . . . . . 17 7.3.9 Overcurrent protection (FBSENSE pin) . . . . . 18 7.3.10 Driver (pin FBDRIVER). . . . . . . . . . . . . . . . . . 18 8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 18 1 2 2.1 2.2 2.3 2.4 2.5 3 4 5 6 6.1 6.2 7 7.1 7.1.1 7.1.2 7.1.3 7.1.4 7.1.5 7.2 7.2.1 7.2.2 9 10 11 12 13 14 14.1 14.2 14.3 14.4 15 16 Thermal characteristics . . . . . . . . . . . . . . . . . Characteristics . . . . . . . . . . . . . . . . . . . . . . . . Application information . . . . . . . . . . . . . . . . . Package outline . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 19 24 26 27 28 28 28 28 28 28 29
Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'.
(c) NXP B.V. 2008.
All rights reserved.
For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 15 December 2008 Document identifier: TEA1750_2

▲Up To Search▲

Price & Availability of TEA1750

	To Download TEA1750 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .