 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HMC399MS8 / 399MS8E v03.0705 HIGH IP3 GaAs MMIC MIXER, 700 - 1000 MHz Designer's Kit Available Typical Applications High Dynamic Range Infrastructure: * GSM, GPRS & EDGE Features +35 dBm Input IP3 Conversion Loss: 8.5 dB Low External Part Count Ultra Small MSOP8 Package: 14.8 mm2 Included in the HMC-DK003 Designer's Kit 7 MIXERS - SMT * CDMA & W-CDMA * Cable Modem Termination Systems Functional Diagram General Description The HMC399MS8 & HMC399MS8E are high dynamic range passive MMIC mixers in plastic surface mount 8 lead Mini Small Outline Packages (MSOP) covering 700 to 1000 MHz. Excellent input IP3 performance of +35 dBm for down conversion and +32 dBm for up conversion is provided for 2.5G & 3G GSM/ CDMA based cellular applications at an LO drive of +17 dBm. With a 1 dB compression of +23 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 8.5 dB typical and LO isolations are maintained at 23 to 35 dB. This miniature single-ended monolithic GaAs FET mixer requires only one external inductor to optimize the LO frequency response. The 50 to 250 MHz IF frequency response will satisfy many cellular transmit or receive frequency plans. The HMC399MS8 & HMC399MS8E input IP3 performance coupled with its high P1dB rivals traditional active FET mixers while offering a much smaller 14.8mm2 standard IC footprint and no DC bias. Electrical Specifications, TA = +25C, LO = +17 dBm, IF = 200 MHz [1] Parameter Frequency Range, RF Frequency Range, LO [2] Frequency Range, IF Conversion Loss Noise Figure (SSB) LO to RF Isolation LO to IF Isolation IP3 (Input) 1 dB Gain Compression (Input) LO Input Drive Level (Typical) 19 22 30 20 Min. Typ. 740 - 800 540 - 740 DC - 200 9 9 23 27 34 24 +16 to +18 10 10 20 26 31 19 Max. Min. Typ. 800 - 900 550 - 840 DC - 250 8.5 8.5 24 31 35 23 +16 to +18 9.5 9.5 21 29 30 18 Max. Min. Typ. 880 - 960 630 - 900 DC - 250 8 8 25 35 34 22 +16 to +18 10 10 Max. Units MHz MHz MHz dB dB dB dB dBm dBm dBm [1] Unless otherwise noted, all measurements performed as a downconverter with low side LO & IF = 200 MHz [2] LO Frequency optimized. See application circuit herein. 7 - 264 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC399MS8 / 399MS8E v03.0705 HIGH IP3 GaAs MMIC MIXER, 700 - 1000 MHz Isolation @ LO = +17 dBm 0 Conversion Gain vs. Temperature @ LO = +17 dBm 0 CONVERSION GAIN (dB) -10 -5 ISOLATION (dB) -20 7 RF TO IF LO TO RF LO TO IF -10 -30 -15 + 25C + 85C - 40C -40 -20 0.7 0.75 0.8 0.85 0.9 RF FREQUENCY (GHz) 0.95 1 -50 0.7 0.75 0.8 0.85 0.9 FREQUENCY (GHz) 0.95 1 Conversion Gain vs. LO Drive 0 Return Loss @ LO = +17 dBm* 0 CONVERSION GAIN (dB) RETURN LOSS (dB) -5 -5 -10 -15 LO =+15dBm LO = +16dBm LO = +17dBm LO = +19dBm -10 LO RF -20 0.7 0.75 0.8 0.85 0.9 RF FREQUENCY (GHz) 0.95 1 -15 0.4 0.5 0.6 0.7 0.8 RF FREQUENCY (GHz) 0.9 1 If Bandwidth @ LO = +17 dBm 0 Upconverter Conversion Gain @ LO = +17 dBm 45 40 -5 RESPONSE (dB) INPUT IP3 (dBm) 35 -10 30 + 15dBm + 16dBm + 17dBm + 19 dBm -15 25 CONVERSION GAIN RETURN LOSS -20 50 100 150 200 250 300 350 IF FREQUENCY (MHz) 400 450 500 20 0.7 0.75 0.8 0.85 0.9 RF FREQUENCY (GHz) 0.95 1 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 265 MIXERS - SMT HMC399MS8 / 399MS8E v03.0705 HIGH IP3 GaAs MMIC MIXER, 700 - 1000 MHz Input IP3 vs. Temperature @ LO = +17 dBm 45 Input IP3 vs. IF Frequency, RF = 850 MHz 45 LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm 40 INPUT IP3 (dBm) 40 INPUT IP3 (dBm) 7 MIXERS - SMT 35 35 30 30 + 25C + 85C - 40C 25 25 20 50 75 100 125 150 175 200 225 IF FREQUENCY (MHz) 250 275 300 20 0.7 0.75 0.8 0.85 0.9 RF FREQUENCY (GHz) 0.95 1 Input IP3 vs. IF Frequency, RF = 950 MHz 45 LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm Input IP3 vs. LO Drive 45 40 INPUT IP3 (dBm) 40 INPUT IP3 (dBm) 35 35 30 30 LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm 25 25 20 50 75 100 125 150 175 200 225 IF FREQUENCY (MHz) 250 275 300 20 0.7 0.75 0.8 0.85 0.9 RF FREQUENCY (GHz) 0.95 1 Input P1dB vs. Temperature @ LO = +17 dBm 30 Upconverter Input IP3 vs. LO Drive 45 40 INPUT P1dB (dBm) 25 INPUT IP3 (dBm) 35 20 30 + 15dBm + 16dBm + 17dBm + 19 dBm 15 +25C +85C -40C 25 10 0.7 0.75 0.8 0.85 0.9 RF FREQUENCY (GHz) 0.95 1 20 0.7 0.75 0.8 0.85 0.9 RF FREQUENCY (GHz) 0.95 1 7 - 266 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC399MS8 / 399MS8E v03.0705 HIGH IP3 GaAs MMIC MIXER, 700 - 1000 MHz Input IP2 vs. Temperature @ LO = +17 dBm 45 Input IP2 vs. LO Drive 45 40 INPUT IP2 (dBm) INPUT IP2 (dBm) 40 35 35 7 LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm 30 + 25C + 85C - 40C 30 25 25 20 0.7 0.75 0.8 0.85 0.9 RF FREQUENCY (GHz) 0.95 1 20 0.7 0.75 0.8 0.85 0.9 RF FREQUENCY (GHz) 0.95 1 MxN Spurious Outputs nLO mRF 0 1 2 3 4 0 xx 3 69 80 81 1 -9 0 75 71 81 2 17 17 57 82 81 3 2 28 62 69 80 4 23 26 65 80 80 Harmonics of LO nLO Spur @ RF Port LO Freq (GHz) 0.4 0.5 0.6 0.7 0.8 0.9 1 34 30 26 24 23 25 2 54 39 35 37 33 31 3 38 35 33 36 42 46 4 45 47 54 47 50 43 RF Freq = 0.801 GHz @ -10 dBm LO Freq = 0.601 GHz @ +17 dBm All values in dBc relative to the IF power level. LO = +17 dBm All values are in dBc below input LO level @ RF port. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 7 - 267 MIXERS - SMT HMC399MS8 / 399MS8E v03.0705 HIGH IP3 GaAs MMIC MIXER, 700 - 1000 MHz Absolute Maximum Ratings RF/IF Input LO Drive +25 dBm +27 dBm -65 to +150 C -40 to +85 C 40 mA 7 MIXERS - SMT Storage Temperature Operating Temperature IF DC Current ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number HMC399MS8 HMC399MS8E Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H399 XXXX H399 XXXX [2] [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX 7 - 268 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC399MS8 / 399MS8E v03.0705 HIGH IP3 GaAs MMIC MIXER, 700 - 1000 MHz Pin Descriptions Pin Number Function Description This pin is AC coupled & matched to 50 Ohms when an external inductor (L1) is connected in series with the LO. Choose value of L1 to optimize LO frequency response. Not connected. Interface Schematic 1 LO 7 MIXERS - SMT 7 - 269 2, 4 N/C 3, 6, 7 GND This pin must be connected to RF ground. 5 IF This pin is DC coupled. For applications not requiring operation to DC this port should be DC blocked externally using a series capacitor. Choose value of C1 to pass IF frequency desired. For operation to DC, this pin must not sink/source more than 40 mA of current or failure may result. 8 RF This pin is DC coupled & matched to 50 Ohms from 700 - 1000 MHz For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC399MS8 / 399MS8E v03.0705 HIGH IP3 GaAs MMIC MIXER, 700 - 1000 MHz Evaluation PCB 7 MIXERS - SMT List of Materials for Evaluation PCB 106334 [1] Item J1 - J3 L1 [3] U1 PCB [2] Description PCB Mount SMA RF Connector 24 nH Chip Inductor, 0805 Pkg HMC399MS8 / HMC399MS8E Mixer 106307 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 [3] Unless otherwise noted, all measurements performed as a downconverter with low side LO & IF = 200 MHz [4] LO Frequency optimized. See application circuit herein. The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. 7 - 270 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC399MS8 / 399MS8E v03.0705 HIGH IP3 GaAs MMIC MIXER, 700 - 1000 MHz Application Circuit 7 MIXERS - SMT 7 - 271 Selection of L1 for Optimal LO Frequency 10% Choose value of L1 to optimize LO Frequency response. For best results use an 0805 size RF inductor or smaller. LO Frequency (MHz) 600 L1 (nH) 24 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com |
Price & Availability of HMC399MS806
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |