Part Number Hot Search : 
2SC1974 SK70KQ16 EN39S R3000 3KA18 B3865 SN8P250 A02HC
Product Description
Full Text Search
 

To Download CY7C65630-56LFXA Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 CY7C656xx
EZ-USB HX2LPTM Low-Power USB 2.0 Hub Controller Family
Features
USB 2.0 hub controller Automotive AEC grade option (-40 - 85C) Compliant with the USB 2.0 specification USB-IF Certified: TID# 30000009 Windows Hardware Quality Lab (WHQL) - compliant Up to four downstream ports supported Supports bus powered and self powered modes Single Transaction Translator (TT) Bus power configurations Fit/form/function compatible with CY7C65640 and CY7C65640A (TetraHubTM) * Space saving 56-pin QFN * Single power supply requirement * * * * * -- Internal regulator for reduced cost Integrated upstream pull up resistor Integrated pull down resistors for all downstream ports Integrated upstream and downstream termination resistors Integrated port status indicator control 24 MHz external crystal (integrated PLL) * * * * * * * * * * * In-system EEPROM programming * Configurable with external SPI EEPROM: -- Vendor ID, Product ID, Device ID (VID/PID/DID) -- Number of active ports -- Number of removable ports -- Maximum power setting for high-speed and full-speed -- Hub controller power setting -- Power on timer -- Overcurrent detection mode -- Enabled/disabled overcurrent timer -- Overcurrent pin polarity -- Indicator pin polarity -- Compound device -- Enable full-speed only -- Disable port indicators -- Ganged power switching -- Self and bus powered compatibility -- Fully configurable string descriptors for multiple language support
Block Diagram CY7C65630
24 MHz Crystal
D+
DHigh-Speed USB Control Logic SPI Communication Block
SPI_SCK SPI_SD SPI_CS
USB 2.0 PHY PLL USB Upstream Port
Serial Interface Engine
Transaction Translator Hub Repeater
TT RAM
Routing Logic
USB Downstream Port 1
USB 2.0 PHY Port Power Control Port Status
USB Downstream Port 2
USB 2.0 PHY Port Power Control Port Status
USB Downstream Port 3
USB 2.0 PHY Port Power Control Port Status
USB Downstream Port 4
USB 2.0 PHY Port Power Control Port Status
D+
D-
PWR#[1] OVR#[1]
LED D+
D- PWR#[2] OVR#[2]
LED
D+
D-
PWR#[3] OVR#[3]
LED D+
D-
PWR#[4] OVR#[4]
LED
Cypress Semiconductor Corporation Document #: 38-08037 Rev. *H
*
198 Champion Court
*
San Jose, CA 95134-1709
* 408-943-2600 Revised May 3, 2007
[+] Feedback
CY7C656xx
Block Diagram CY7C65620
D+ DHigh-Speed USB Control Logic SPI Communication Block
SPI_SCK SPI_SD SPI_CS
USB 2.0 PHY
24 MHz Crystal
PLL USB Upstream Port
Serial Interface Engine
Transaction Translator (X1) Hub Repeater
TT RAM
Routing Logic
USB Downstream Port 1
USB 2.0 PHY Port Power Control Port Status
USB Downstream Port 2
USB 2.0 PHY Port Power Control Port Status
USB Downstream Port 3
USB 2.0 PHY Port Power Control Port Status
USB Downstream Port 4
USB 2.0 PHY Port Power Control Port Status
D+
D- PWR#[1] OVR#[1]
LED
D+
D-
PWR#[2] OVR#[2]
LED
D+
D- PWR#[3] OVR#[3]
LED D+
D-
PWR#[4] OVR#[4]
LED
Introduction
EZ-USB HX2LPTM is Cypress' next generation family of high performance, low power USB 2.0 hub controllers. HX2LP is an ultra low power single chip USB 2.0 hub controller with integrated upstream and downstream transceivers, a USB Serial Interface Engine (SIE), USB Hub Control and Repeater logic, and Transaction Translator (TT) logic. Cypress has also integrated many of the external passive components, such as pull up and pull down resistors, reducing the overall bill of materials required to implement a hub design. The HX2LP portfolio consists of: 1. CY7C65630: 4-port/single transaction translator This device option is for ultra low power applications that require four downstream ports. All four ports share a single transaction translator. The CY7C65630 is available in a 56 QFN and is also pin-for-pin compatible with the CY7C65640.
2. CY7C65620: This device option is for a 2-port bus powered application. Both ports share a single transaction translator. The CY7C65620 is available in a 56 QFN. All device options are supported by Cypress' world class reference design kits, which include board schematics, bill of materials, Gerber files, Orcad files, and thorough design documentation. USB Serial Interface Engine The Serial Interface Engine (SIE) allows the CY7C656xx to communicate with the USB host. The SIE handles the following USB activity independently of the Hub Control Block. * Bit stuffing/unstuffing * Checksum generation/checking * TOKEN type identification * Address checking.
Document #: 38-08037 Rev. *H
Page 2 of 24
[+] Feedback
CY7C656xx
Hub Repeater The Hub Repeater manages the connectivity between upstream and downstream facing ports that are operating at the same speed. It supports full-/low-speed connectivity and high-speed connectivity. According to the USB 2.0 specification, the HUB Repeater provides the following functions: * Sets up and tears down connectivity on packet boundaries * Ensures orderly entry into and out of the Suspend state, including proper handling of remote wakeups. Transaction Translator The Transaction Translator (TT) basically translates data from one speed to another. A TT takes high-speed split transactions and translates them to full-/low-speed transactions when the hub is operating at high speed (the upstream port is connected to a high-speed host controller) and has full-/low-speed devices attached. The operating speed of a device attached on a downstream facing port determines whether the Routing Logic connects a port to the Transaction Translator or Hub Repeater. If a full-/low-speed device is connected to the hub operating at high speed, the data transfer route includes the Transaction Translator. If a high-speed device is connected to this high-speed hub, the route only includes the repeater and no Transaction Translator since the device and the hub are operating at the same speed. When the hub is operating at full speed (the upstream port is connected to a full-speed host controller), a high-speed peripheral does not operate at its full capability. These devices only work at full speed. Full- and low-speed devices connected to this hub operate at their normal speed.
System Initialization On power up, the CY7C656xx reads an external SPI EEPROM for configuration information. At the most basic level, this EEPROM has the Vendor ID (VID), Product ID (PID), and Device ID (DID) for the customer's application. For more specialized applications, other configuration options can be specified. See "Configuration Options" on page 11 for more details. After reading the EEPROM, if VBUSPOWER (connected to up-stream VBUS) is high, CY7C656xx enables the pull up resistor on D+ to indicate its presence to the upstream hub, after which a USB Bus Reset is expected. During this reset, CY7C656xx initiates a chirp to indicate that it is a high-speed peripheral. In a USB 2.0 system, the upstream hub responds with a chirp sequence, and CY7C656xx is in a high-speed mode, with the upstream D+ pull up resistor turned off. In USB 1.x systems, no such chirp sequence from the upstream hub is seen, and CY7C656xx operates as a normal 1.x hub (operating at full speed). Enumeration After a USB Bus Reset, CY7C656xx is in an unaddressed, unconfigured state (configuration value set to '0'). During the enumeration process, the host sets the hub's address and configuration. Once the hub is configured, the full hub functionality is available. Downstream Ports The CY7C656xx supports a maximum of four downstream ports, each of which may be marked as usable or removable in the extended configuration (0xD2 EEPROM load or 0xD4 EEPROM load, see "Configuration Options" on page 11. Downstream D+ and D- pull down resistors are incorporated in CY7C656xx for each port. Before the hubs are configured, the ports are driven SE0 (Single Ended Zero, where both D+ and D- are driven low) and are set to the unpowered state. Once the hub is configured, the ports are not driven, and the host may power the ports by sending a SetPortPower command for each port. After a port is powered, any connect or disconnect event is detected by the hub. Any change in the port state is reported by the hubs back to the host through the Status Change Endpoint (endpoint 1). Upon receipt of SetPortReset request for a port with a device connected, the hub does as follows: * Performs a USB Reset on the corresponding port * Puts the port in an enabled state * Enables the green port indicator for that port (if not previously overridden by the host) * Enables babble detection once the port is enabled. Babble consists of a non-idle condition on the port after EOF2. If babble is detected on an enabled port, that port is disabled. A ClearPortEnable request from the host also disables the specified port. Downstream ports can be individually suspended by the host with the SetPortSuspend request. If the hub is not suspended, a remote wakeup event on that port is reflected to the host through a port change indication in the Hub Status Change Endpoint. If the hub is suspended, a remote wakeup event on
Applications
Typical applications for the HX2LP device family are: * Standalone hubs * Motherboard hubs * Monitor hubs * Advanced port replicators * Docking stations * Split-PC designs * External personal storage drives * Keyboard hubs
Functional Overview
The Cypress CY7C656xx USB 2.0 Hubs are high performance, low system cost solutions for USB. The CY7C656xx USB 2.0 Hubs integrate 1.5 k upstream pull up resistors for full-speed operation and all downstream 15 k pull down resistors as well as series termination resistors on all upstream and downstream D+ and D- pins. This results in optimization of system costs by providing built-in support for the USB 2.0 specification.
Document #: 38-08037 Rev. *H
Page 3 of 24
[+] Feedback
CY7C656xx
this port is forwarded to the host. The host may resume the port by sending a ClearPortSuspend command. Upstream Port The upstream port includes the transmitter and the receiver state machine. The transmitter and receiver operate in high speed and full speed depending on the current hub configuration. The transmitter state machine monitors the upstream facing port while the Hub Repeater has connectivity in the upstream direction. This machine prevents babble and disconnect events on the downstream facing ports of this hub from propagating and causing the hub to be disabled or disconnected by the hub to which it is attached. Power Switching The CY7C656xx includes interface signals for external port power switches. Both ganged and individual (per-port) configurations are supported, with individual switching being the default. Initially all ports are unpowered. After enumerating, the host may power each port by sending a SetPortPower request for that port. The power switching and over-current detection of downstream ports is managed by control pins connected to an external power switch device. PWR [n]# output pins of the CY7C656xx series are connected to the respective external power switch's port power enable signals. (Note that each port power output pin of the external power switch must be bypassed with an electrolytic or tantalum capacitor as required by the USB specification. These capacitors supply the inrush currents, which occur during downstream device hot-attach events.) The polarity of this pin can be configured through the EEPROM; see "0xD4 Load" on page 13. Overcurrent Detection Overcurrent detection includes 8 ms of timed filtering by default. This parameter is configured from the external EEPROM in a range of 0 ms to 15 ms for both enabled ports and disabled ports individually. Detection of over-current on downstream ports is managed by control pins connected to an external power switch device.
The OVR[n]# pins of the CY7C656xx series are connected to the respective external power switch's port over-current indication (output) signals. Upon detecting an over-current condition, the hub reports the overcurrent condition to the host and disables the PWR# output to the external power device. The polarity of the OVR pins can be configured through the EEPROM; see "0xD4 Load" on page 13. Port Indicators The USB 2.0 port indicators are also supported directly by the CY7C656xx. In accordance with the specification, each downstream port of the hub optionally supports a status indicator. The presence of indicators for downstream facing ports is specified by bit 7 of the wHubCharacteristics field of the hub class descriptor. The default CY7C656xx descriptor specifies that port indicators are supported (wHubCharacteristics, bit 7 is set). If port indicators are not included in the hub, disable this bit through EEPROM settings. Each port indicator pin is strategically located directly on the opposite edge of the port with which it is associated. A port indicator provides two colors: green and amber. This is usually implemented as two separate LEDs, one amber and the other green. A combination of hardware and software control is used to inform the user of the current status of the port or the device attached to the port and to guide the user through problem resolution. Colors and blinking provide information to the user. The significance of the color of the LED depends on the operational mode of the CY7C656xx. There are two modes of operation for the CY7C656xx port indicators: automatic and manual. On power up the CY7C656xx defaults to automatic mode, where the color of the Port Indicator (green, amber, off) indicates the functional status of the CY7C656xx port. In automatic mode, the CY7C656xx turns on the green LED whenever the port is enabled and the amber LED when an overcurrent condition is detected. The color of the port indicator is set by the port state machine. Blinking of the LEDs is not supported in automatic mode. Table 1 identifies the mapping of color to port state in automatic mode.
Table 1. Automatic Port State to Port Indicator Color Mapping Downstream Facing Hub Port State Powered Off Off or Amber, if due to an Overcurrent Condition Disconnected, Disabled, Not Configured, Resetting, Testing Off Enabled, Transmit, or TransmitR Green Suspended, Resuming, SendEOR, Restart_E/S Off
Document #: 38-08037 Rev. *H
Page 4 of 24
[+] Feedback
CY7C656xx
The LED control lines can also be modulated with a square wave for power conservation. The polarity of these pins is programmable, see "0xD4 Load" on page 13. In manual mode, the indicators are under the control of the host, which can turn on the LEDs, or leave them off. This is done by a USB Hub class request. Blinking of the LEDs is supported in manual mode. The port indicators allow the user to intervene in any error detection. For example, when babble is detected while plugging in a defective device, or when an overcurrent condition occurs, the port indicators corresponding to the downstream port blink green or only light the amber LED, respectively.
Table 2 displays the color definition of the indicators when CY7C656xx is in manual mode.[1] Table 2. Port Indicator Color Definitions in Manual Mode Color Definition Off Amber Green Blinking Off/Green Blinking Off/Amber Blinking Green/Amber Port State Not operational Error condition Fully Operational Software Attention Hardware Attention Reserved
Note 1. Information presented in Table 1 and Table 2 is from USB 2.0 specification Tables 11-6 and 11-7, respectively.
Document #: 38-08037 Rev. *H
Page 5 of 24
[+] Feedback
CY7C656xx
Pin Configuration
Figure 1. 56-pin Quad Flat Pack No Leads (8 mm x 8 mm)[2]
OVR#[3]/Rsvd OVR#[4]/Rsvd PWR#[3]/NC PWR#[4]/NC GREEN#[4]/NC 43 AMBER#[4]/NC 44
56
55
54
53
52
51
50
49
48
47
46
DD-[4]/NC
1 2 3
SELFPWR 45
SPI_SCK
SPI_SD
RESET
GND
VCC
GND
GND
42 AMBER#[3]/NC 41 GREEN#[3]/NC 40 GND
DD+[4]/NC VCC
GND 4 DD-[3]/NC DD+[3]/NC VCC GND DD-[2]
39 VCC 38 AMBER#[2] 37 GREEN#[2] 36 AMBER#[1] 35 GREEN#[1] 34 GND 33 VCC 32 OVR#[2] 31 PWR#[2] 30 OVR#[1]
5 6 7 8 9
DD+[2] 10 VCC 11 GND 12 DD-[1] 13 DD+[1] 14
29 PWR#[1]
15 VCC
16 GND
17 D-
18 D+
19 VCC
20 GND
21 XIN
22 XOUT
23 VCC
24 GND
25 SPI_CS
26 VBUSPOWER
27 VCC
28 GND
Note 2. NC and Rsvd are for CY7C65620 ONLY.
Document #: 38-08037 Rev. *H
Page 6 of 24
[+] Feedback
CY7C656xx
Pin Description Table
Table 3. Pin Assignments[3] Pin 3 7 11 15 19 23 27 33 39 55 4 8 12 16 20 24 28 34 40 47 50 56 21 22 46 CY7C65630 Name VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC GND GND GND GND GND GND GND GND GND GND GND GND XIN XOUT RESET# CY7C65620 Name VCC VCC VCC VCC VCC VCC VCC VCC VCC VCC GND GND GND GND GND GND GND GND GND GND GND GND XIN XOUT RESET# Type Default Power Power Power Power Power Power Power Power Power Power Power Power Power Power Power Power Power Power Power Power Power Power Input Output Input N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Description VCC. This signal provides power to the chip. VCC. This signal provides power to the chip. VCC. This signal provides power to the chip. VCC. This signal provides power to the chip. VCC. This signal provides power to the chip. VCC. This signal provides power to the chip. VCC. This signal provides power to the chip. VCC. This signal provides power to the chip. VCC. This signal provides power to the chip. VCC. This signal provides power to the chip. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. GND. Connect to Ground with as short a path as possible. 24-MHz Crystal IN or External Clock Input. 24-MHz Crystal OUT. (NC if external clock is used) Active LOW Reset. This pin resets the entire chip. It is normally tied to VCC through a 100K resistor, and to GND through a 0.1-F capacitor. Other than this, no other special power up procedure is required. Self Power. Indicator for bus or self powered. 0 is bus powered, 1 is self powered. VBUS. Connect to the VBUS pin of the upstream connector. This signal indicates to the hub that it is in a connected state, and may enable the D+ pull up resistor to indicate a connection. (The hub does so after the external EEPROM is read). SPI Chip Select. Connect to CS pin of the EEPROM. SPI Clock. Connect to EEPROM SCK pin. SPI Dataline Connect to GND with 15-K resistor and to the Data I/O pin of the EEPROM.
45 26
SELFPWR
SELFPWR
Input
N/A N/A
VBUSPOWER VBUSPOWER Input
SPI Interface 25 48 49 SPI_CS SPI_SCK SPI_SD SPI_CS SPI_SCK SPI_SD Output Output I/O/Z O O Z
Note 3. Unused port DD+/DD- lines can be left floating. Leave the port power, amber, and green LED pins unconnected, and deassert the overcurrent pin. Do not leave the overcurrent pin floating; it is an input.
Document #: 38-08037 Rev. *H
Page 7 of 24
[+] Feedback
CY7C656xx
Table 3. Pin Assignments[3] (continued) Pin CY7C65630 Name D- D+ DD-[1] DD+[1] AMBER#[1] GREEN#[1] OVR#[1] PWR#[1] CY7C65620 Name D- D+ DD-[1] DD+[1] AMBER#[1] GREEN#[1] OVR#[1] PWR#[1] Type Default Description
Upstream Port 17 18 13 14 36 35 30 29 I/O/Z I/O/Z I/O/Z I/O/Z Output Output Input O/Z Z Z Z Z 1 1 1 Z Upstream D- Signal. Upstream D+ Signal. Downstream D- Signal. Downstream D+ Signal. LED. Driver output for Amber LED. Port Indicator Support. Default is Active LOW. Polarity is controlled through EEPROM. LED. Driver output for Green LED. Port Indicator Support. Default is Active LOW. Polarity is controlled through EEPROM. Overcurrent Condition Detection Input. Default is Active LOW. Polarity is controlled through EEPROM. Power Switch Driver Output. Default is Active LOW. Polarity is controlled through EEPROM. Downstream D- Signal. Downstream D+ Signal. LED. Driver output for Amber LED. Port Indicator Support. Default is Active LOW. Polarity is controlled through EEPROM. LED. Driver output for Green LED. Port Indicator Support. Default is Active LOW. Polarity is controlled through EEPROM. Overcurrent Condition Detection Input. Default is Active LOW. Polarity is controlled through EEPROM. Power Switch Driver Output. Default is Active LOW. Polarity is controlled through EEPROM. Downstream D- Signal. Downstream D+ Signal. LED. Driver output for Amber LED. Port Indicator Support. Default is Active LOW. Polarity is controlled through EEPROM. LED. Driver output for Green LED. Port Indicator Support. Default is Active LOW. Polarity is controlled through EEPROM. Overcurrent Condition Detection Input. Default is Active LOW. Polarity is controlled through EEPROM. Reserved. Pull to deasserted state with external resistor (CY7C65620 only) Power Switch Driver Output. Default is Active LOW. Polarity is controlled through EEPROM. Downstream D- Signal. Downstream D+ Signal. LED. Driver output for Amber LED. Port Indicator Support. Default is Active LOW. Polarity is controlled through EEPROM. LED. Driver output for Green LED. Port Indicator Support. Default is Active LOW. Polarity is controlled through EEPROM.
Downstream Port 1
Downstream Port 2 9 10 38 37 32 31 DD-[2] DD+[2] AMBER#[2] GREEN#[2] OVR#[2] PWR#[2] DD-[2] DD+[2] AMBER#[2] GREEN#[2] OVR#[2] PWR#[2] I/O/Z I/O/Z Output Output Input O/Z Z Z 1 1 1 Z
Downstream Port 3 5 6 42 41 53 DD-[3] DD+[3] AMBER#[3] GREEN#[3] OVR#[3] NC NC NC NC Reserved I/O/Z I/O/Z Output Output Input Z Z 1 1 1
54
PWR#[3]
NC
O/Z
Z
Downstream Port 4 1 2 44 43 DD-[4] DD+[4] AMBER#[4] GREEN#[4] NC NC NC NC I/O/Z I/O/Z Output Output Z Z 1 1
Document #: 38-08037 Rev. *H
Page 8 of 24
[+] Feedback
CY7C656xx
Table 3. Pin Assignments[3] (continued) Pin 51 CY7C65630 Name OVR#[4] CY7C65620 Name Reserved Type Default Input 1 Description Overcurrent Condition Detection Input. Default is Active LOW. Polarity is controlled through EEPROM. Reserved. Pull to deasserted state with external resistor (CY7C65620 only) Power Switch Driver Output. Default is Active LOW. Polarity is controlled through EEPROM.
52
PWR#[4]
NC
O/Z
Z
Default Descriptors
This section presents the different descriptors that are available. There is a table for each that lists the functionality of each descriptor. Device Descriptor The standard device descriptor for CY7C656xx is based on the information found in the SPI EEPROM. The information in Byte 0 1 2,3 4 5 6 7 8,9 10,11 12, 13 14 15 16 17 Full-Speed 0x12 0x01 0x0110 0x09 0x00 0x00 0x40 0x04B4 0x6560 0x0915 0x00 0x00 0x00 0x01 High-Speed 0x12 0x01 0x0200 0x09 0x00 0x01 0x40 0x04B4 0x6560 0x0915 0x00 0x00 0x00 0x01 the EEPROM overrides the default descriptor values. If no EEPROM is used, the CY7C656xx enumerates with the default descriptor values as shown below. If a blank EEPROM is connected, the hub enumerates as vendor defined class instead of a hub class. This is for the purpose of programming the EEPROM with the Cypress driver.
Field Name bLength bDescriptorType bcdUSB bDeviceClass bDeviceSubClass bDeviceProtocol bMaxPacketSize0 wIdVendor wIdProduct wbcdDevice iManufacturer iProduct iSerialNumber bNumConfigurations 18 Bytes
Description DEVICE_DESCRIPTOR USB specification 2.0 (1.1 if forced FS) HUB None None 64 bytes VID (overridden by what is defined in EEPROM) PID (overridden by what is defined in EEPROM) DID (overridden by what is defined in EEPROM) Overridden by EEPROM Overridden by EEPROM Overridden by EEPROM One configuration supported
Configuration Descriptor Byte 0 1 2 4 5 6 7 8 Full-Speed 0x09 0x02[4]/0x07[5] 0x0019 0x01 0x01 0x00 0xA0 0xE0 0x28 High-Speed 0x09 0x0019 0x01 0x01 0x00 0xA0 0xE0 0x57[4] Field Name bLength wTotalLength bNumInterfaces bConfigurationValue iConfiguration bmAttributes bMaxPower Value depends on pin 45 - SELFPWR signal SELFPWR = 0 yields 0xA0 and =1 yields 0xE0 9 Bytes CONFIG_DESCRIPTOR Length of all other descriptors 1 The configuration to use Description
0x02[4]/0x07[5] bDescriptorType
Notes 4. Configured speed descriptor. 5. Other speed descriptor.
Document #: 38-08037 Rev. *H
Page 9 of 24
[+] Feedback
CY7C656xx
Interface Descriptor Byte 0 1 2 3 4 5 6 7 8 Full-Speed 0x09 0x04 0x00 0x00 0x01 0x09 0x00 0x00 0x00 High-Speed 0x09 0x04 0x00 0x00 0x01 0x09 0x00 0x00 0x00 Field Name bLength bDescriptorType bInterfaceNumber bAlternateSetting bNumEndpoints bInterfaceClass bInterfaceSubClass bInterfaceProtocol iInterface 9 Bytes INTERFACE_DESCRIPTOR Description
Endpoint Descriptor Byte 0 1 2 3 4,5 6 Full-Speed 0x07 0x05 0x81 0x03 0x0001 0xFF High-Speed 0x07 0x05 0x81 0x03 0x0001 0x0C Field Name bLength bDescriptorType bEndpointAddress bmAttributes wMaxPacketSize bInterval 7 Bytes ENDPOINT_DESCRIPTOR IN Endpoint #1 Interrupt Maximum Packet Size Polling Rate Description
Device Qualifier Descriptor Byte 0 1 2,3 4 5 6 7 8 9 Hub Descriptor Byte 0 1 2 All Speed 0x09 0x29 0x04[6] 0x02 Field Name bLength bDescriptorType bNbrPorts 9 Bytes HUB Descriptor Number of ports supported, CY7C65630. Number of ports supported, CY7C65620. Description Full-Speed 0x0A 0x06 0x0200 0x09 0x00 0x01 0x40 0x01 0x00 High-Speed 0x0A 0x06 0x0200 0x09 0x00 0x00 0x40 0x01 0x00 Field Name bLength bDescriptorType bcdUSB bDeviceClass bDeviceSubClass bDeviceProtocol bMaxPacketSize0 bNumConfigurations bReserved 10 Bytes DEVICE_QUALIFIER Description
Note 6. This value is configured through the External EEPROM.
Document #: 38-08037 Rev. *H
Page 10 of 24
[+] Feedback
CY7C656xx
Byte 3,4
All Speed 0x0089[6]
Field Name wHubCharacteristics
Description b1, b0: Logical Power Switching Mode 00: Ganged power switching (all ports' power at once) 01: Individual port power switching (Default in CY7C656xx) b2: Identifies a Compound Device, 0: Hub is not part of a compound device (Default in CY7C656xx), 1: Hub is part of a compound device. b4, b3: Overcurrent Protection Mode 00: Global Overcurrent Protection. The hub reports overcurrent as a summation of all ports' current draw, without a breakdown of individual port overcurrent status. 01: Individual Port Overcurrent Protection. The hub reports overcurrent on a per-port basis. Each port has an over-current status (Default in CY7C656xx). 1X: No Overcurrent Protection. This option is allowed only for bus-powered hubs that do not implement overcurrent protection. b6, b5: TT Think Time 00: TT requires at most eight FS bit times of inter transaction gap on a full-/low-speed downstream bus (Default in CY7C656xx). b7: Port Indicators Supported, 0: Port Indicators are not supported on its downstream facing ports and the SetPortIndicator request has no effect. 1: Port Indicators are supported on its downstream facing ports and the SetPortIndicator request controls the indicators. See the Functional Overview Section and the Supported USB Requests Section. (Default in CY7C656xx). b15,. b8: Reserved Time from when the port is powered to when the power is good on that port Maximum current requirement for the Hub Controller at full speed. Maximum current requirement for the Hub Controller at high speed. Indicates if the logical port has a removable device attached (0 = removable, 1 = non-removable) Required for compatibility with software written for 1.0 compliant devices 0xD0 Load With this EEPROM format, only a unique VID, PID, and DID must be present in the external SPI EEPROM. The contents of the EEPROM must contain this information in the following format: Byte 0 1 2 3 4 5 6 Value 0xD0 VID (LSB) VID (MSB) PID (LSB) PID (MSB) reserved DID (MSB)
5 6 7 8
0x32[6] 0x28[6] 0xAE[6] 0x00[6] 0xFF[6]
bPwrOn2PwrGood bHubContrCurrent bDeviceRemovable bPortPwrCtrlMask
Configuration Options
Systems using CY7C656xx may have the option of using a fuse ROM which is preset at the factory to configure the hub, otherwise it must have an external EEPROM in order for the device to have a unique VID, PID, and DID. The CY7C656xx can communicate with SPI EEPROM that are either double byte addressed or single byte with the 9th bit within the instruction byte, such as the 24LC040 parts use. The 25LC080 EEPROM uses the double byte address format, and therefore the CY7C656xx can communicate with these parts. The '010s and '020s use the same command format as is used to interface with the `040 and hence these can also be used to interface with the CY7C656xx. If the attached EEPROM is blank (0xFF) the hub enumerates as a vendor class device. In this configuration the hub connects to the Cypress driver to allow programming of the EEPROM. Once the EEPROM is programmed a power cycle configures the chip as a hub class device.
Document #: 38-08037 Rev. *H
Page 11 of 24
[+] Feedback
CY7C656xx
0xD2 Load Byte 0 1 2 3 4 5 6 7 8 9 10 11 12 0xD2 VID (LSB) VID (MSB) PID (LSB) PID (MSB) reserved DID (MSB) EnabledOverCurrentTimer[3:0], DisableOvercurrentTimer[3:0] ActivePorts[3:0], RemovablePorts[3:0] MaxPower HubControllerPower PowerOnTimer IllegalHubDescriptor, CompoundDevice, FullspeedOnly, NoPortIndicators, Reserved, GangPowered, Reserved, Reserved Value (MSB->LSB)
field is calculated from this. Bits 3-0 are the RemovablePorts[3:0] bits that indicates whether the corresponding logical port is removable (set to high). Logical port numbers are from 1 to n where n is the total number of active ports. If port 2 is disabled then physical ports 1, 3, and 4 map to logical ports 1, 2, and 3. These bit values are reported appropriately in the HubDescriptor:DeviceRemovable field. Default: 0xFF. Byte 9: MaximumPower This value is reported in the ConfigurationDescriptor:bMaxPower field and is the current in 2-mA increments that is required from the upstream hub. Default: 0x28 = 80 mA for full-speed and 0x57 = 174 mA for high-speed. Byte 10: HubControllerPower This value is reported in the HubDescriptor:bHubContrCurrent field and is the current in milliamperes required by the hub controller. Default: 0x50 = 80 mA for full-speed and 0xAE = 174 mA for high-speed. Byte 11: PowerOnTimer This value is reported in the HubDescriptor: bPwrOn2PwrGood field and is the time in 2-ms intervals from the SetPortPower command until the power on the corresponding downstream port is good. Default: 0x32 = 100 ms. Byte 12: IllegalHubDescriptor, CompoundDevice, Full-speedOnly, NoPortIndicators, Reserved, GangPowered, SingleTTOnly Bit 7: IllegalHubDescriptor. For GetHubDescriptor request, some USB hosts use a DescriptorTypeof 0x00 instead of HUB_DESCRIPTOR, 0x29. According to the USB 2.0 standard, a hub must treat this as a Request Error, and STALL the transaction accordingly (USB 2.0, 11.24.2.5). For systems that do not accept this, the IllegalHubDescriptor configuration bit may be set to allow CY7C656xx to accept a DescriptorType of 0x00 for this command. Default is 1. Bit 6: CompoundDevice. Indicates whether the hub is part of a compound device. This is reported in the HubDescriptor, wHub-Characteristics: b2. Default set to '0'. Bit 5: Fullspeed. Only configures the hub to be a full-speed only device. Default is set to '0'. Bit 4: NoPortIndicators. Turns off the port indicators and does not report them as present in the HubDescriptor, wHubCharacteristics b7 field. Default is set to '0'. Bit 3: Reserved. Set this bit to '0'. Bit 2: GangPowered. Indicates whether the port power switching is ganged (set to 1) or per-port (set to '0'). This is reported in the HubDescriptor, wHubCharacteristics field, b4, b3, b1, and b0. Default is set to '0'. Bit 1: Reserved. Default is set to '0'. Bit 0: Reserved. Default is set to '0'.
Byte 0: 0xD2 Needs to be programmed with 0xD2 Byte 1: VID (LSB) Least Significant Byte of Vendor ID Byte 2: VID (MSB) Most Significant Byte of Vendor ID Byte 3: PID (LSB) Least Significant Byte of Product ID Byte 4: PID (MSB)] Most Significant Byte of Product ID Byte 5: Reserved Reserved. Byte 6: DID (MSB)] Most Significant Byte of Device ID Byte 7: EnabledOvercurrentTimer[3:0], DisabledOvercurrentTimer[3:0] Count time in ms for filtering overcurrent detection. Bits 7-4 are for an enabled port, and bits 3-0 are for a disabled port. Both range from 0 ms to 15 ms. See section "Port Indicators" on page 4. Default: 8 ms = 0x88. Byte 8: ActivePorts[3:0], RemovablePorts[3:0] Bits 7-4 are the ActivePorts[3:0] bits that indicates if the corresponding port is usable. For example, a two-port hub that uses ports 1 and 4 would set this field to 0x09. The total number of ports reported in the Hub Descriptor: bNbrPorts
Document #: 38-08037 Rev. *H
Page 12 of 24
[+] Feedback
CY7C656xx
0xD4 Load Byte 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Value (MSB->LSB) 0xD4 VID (LSB) VID (MSB) PID (LSB) PID (MSB) reserved DID (MSB) EnabledOverCurrentTimer[3:0], DisableOvercurrentTimer[3:0] MaxPower (Full-speed) MaxPower (High-speed) Reserved Reserved HubControllerPower Full-Speed Bus Powered HubControllerPower High-Speed Bus Powered HubControllerPower Full-Speed Self Powered HubControllerPower High-Speed Self Powered PowerOnTimer IllegalHubDescriptor, CompoundDevice, FullspeedOnly, NoPortIndicators, Reserved, GangPowered, SingleTTOnly, Reserved AmberPolarity, GreenPolarity, ModulateIndicators, PowerControlPolarity, OverCurrentPolarity, OverCurrentMode1, OverCurrentMode2 Write Protect NumLangs SupportedStrings ActivePorts[3:0] RemovablePorts[3:0] LangID iManufacturer iProduct iSerialNumber iConfiguration(FS) iConfiguration(HS) iInterface(0) Factory Fusable X X X X X
Byte g reserved =f+2N h=g+2N Strings N:NumLangs Byte 0: 0xD4
Value (MSB->LSB)
Factory Fusable
Needs to be programmed with 0xD4 Byte 1: VID (LSB) Least Significant Byte of Vendor ID Byte 2: VID (MSB) Most Significant Byte of Vendor ID Byte 3: PID (LSB) Least Significant Byte of Product ID Byte 4: PID (MSB)
X X
X X
Most Significant Byte of Product ID Byte 5: Reserved Reserved. Byte 6: DID (MSB) Most Significant Byte of Device ID Byte 7: EnabledOvercurrentTimer[3:0], DisabledOvercurrentTimer[3:0]
X
Count time in ms for filtering overcurrent detection. Bits 7-4 are for an enabled port, and bits 3-0 are for a disabled port. Both range from 0 ms to 15 ms. See section "Port Indicators" on page 4. Default: 8 ms = 0x88. Byte 8: MaximumPower (Full-Speed) This value is reported in the ConfigurationDescriptor:bMaxPower field and is the current in 2-mA increments that is required from the upstream hub when connected at full-speed. Default: 0x28 = 80 mA for full-speed. Byte 9: MaximumPower (High-Speed) This value is reported in the ConfigurationDescriptor:bMaxPower field and is the current in 2-mA increments that is required from the upstream hub when connected at high-speed. Default: 0x57 = 174 mA for high-speed.
18
X
19 20 21 22 23 24 a =24+2N b =a+2N c =b+2N d =c+2N e =d+2N f =e+2N
X
Byte 10: Reserved Write zeros to this location. Byte 11: Reserved Write zeros to this location. Byte 12: HubControllerPower (Full-Speed, bus powered) This value is reported in the HubDescriptor:bHubContrCurrent field and is the current in milliamperes required by the hub controller when connected on the upstream hub as a full-speed. Default: 0x50 = 80 mA for full-speed. Byte 13: HubControllerPower (High-speed, bus powered) This value is reported in the HubDescriptor:bHubContrCurrent field and is the current in milliamperes required by the hub controller when connected on the upstream hub as a high-speed. Default: 0xAE = 174 mA for high-speed. Page 13 of 24
Document #: 38-08037 Rev. *H
[+] Feedback
CY7C656xx
Byte 14: HubControllerPower (Full-Speed, self powered) This value is reported in the HubDescriptor:bHubContrCurrent field and is the current in milliamperes required by the hub controller when connected on the upstream hub as a full-speed. Default: 0x50 = 80 mA for full-speed Byte 15: HubControllerPower (High-speed, self powered) This value is reported in the HubDescriptor:bHubContrCurrent field and is the current in milliamperes required by the hub controller when connected on the upstream hub as a high-speed. Default: 0x64 = 100 mA for high-speed. Byte 16: PowerOnTimer This value is reported in the HubDescriptor: bPwrOn2PwrGood field and is the time in 2-ms increments from the SetPortPower command until the power on the corresponding downstream port is good. Default: 0x32 = 100 ms. Byte 17: IllegalHubDescriptor, CompoundDevice, Full-speedOnly, NoPortIndicators, Reserved, GangPowered, Reserved Bit 7: IllegalHubDescriptor. For GetHubDescriptor request, some USB hosts use a DescriptorTypeof 0x00 instead of HUB_DESCRIPTOR, 0x29. According to the USB 2.0 standard, a hub must treat this as a Request Error, and STALL the transaction accordingly (USB 2.0, 11.24.2.5). For systems that do not accept this, the IllegalHubDescriptor configuration bit may be set to allow CY7C656xx to accept a DescriptorType of 0x00 for this command. Default set to 1. Bit 6: CompoundDevice. Indicates whether the hub is part of a compound device. This is reported in the HubDescriptor, wHub-Characteristics: b2. Default is set to '0'. Bit 5: Fullspeed. Only configures the hub to be a full-speed only device. Default is set to '0'. Bit 4: NoPortIndicators. Turns off the port indicators and does not report them as present in the HubDescriptor, wHubCharacteristics b7 field. Default is set to '0'. Bit 3: Reserved. Set this bit to `0'. Bit 2: GangPowered. Indicates whether the port power switching is ganged (set to 1) or per-port (set to '0'). This is reported in the HubDescriptor, wHubCharacteristics field, b4, b3, b1, and b0. Default is set to '0'. Bit 1: Reserved. Default is set to '0'. Bit 0: Reserved. Default is set to '0'. Byte 18: AmberPolarity, GreenPolarity, SelfPowerable, ModulateIndicators, PowerControlPolarity, OverCurrentPolarity, OverCurrentMode1, OverCurrentMode2 Bit 7: AmberPolarity. Indicates the polarity of the amber indicator control. (1 = high, 0 = low) Bit 6: GreenPolarity. Indicates the polarity of the green indicator control. (1 = high, 0 = low) Bit 5: SelfPowerable. Indicates whether the hub is capable of operating in self-powered mode. If `0', the hub is capable of bus-powered operation only.
Bit 4: ModulateIndicators. If this bit is set, the indicator outputs are modulated by a square wave of 120 Hz, for power savings. If `0', the outputs are static. Bit 3: PowerControlPolarity. If set, the power control outputs are active HIGH. If not set, the power control outputs are active LOW. Bit 2: OverCurrentPolarity. If set, the over-current inputs are active HIGH. If not set, the over-current inputs are active LOW. Bit 1: OverCurrentMode1. Reported as bit 4 of the wHubCharacteristics field of the hub descriptor. If set to `1', this bit disables over-current detection. Bit 0: OverCurrentMode2. Reported as bit 3 of the wHubCharacteristics field of the hub descriptor. If Bit 1 of this byte is set to `0', over-current detection is enabled. If this bit (Bit 0) is set to `1', the hub reports over-current on a per-port basis. If set to `0', the hub reports over-current as the summation of all ports' current draw. Byte 19: Write Protect Writing the value 0x42 to this field enables Write Protect and any future writes to the EEPROM will fail. Default is set to `0'. Byte 20: NumLangs Number of supported string languages. CY7C656xx supports a maximum of 31 languages; if this field is set to '0' or a number larger than 31, all string support is disabled. Byte 21: SupportedStrings This field contains a bitmap of strings supported by the hub. A set bit indicates that the standard string is supported. A bit not set indicates that the string is not supported. The hub controller returns a non-zero index for each string that is supported, and returns 0x00 for each string not supported, as indicated by this field. The bits in this field correspond to the following standard strings. Bit Name 7 6 5 reserved reserved iInterface (0) The iInterface string index reported in the first interface descriptor (alternate setting 0). (high-speed) The iConfiguration string index reported in the configuration descriptor, when operating at high-speed. (full-speed) The iConfiguration string index reported in the configuration descriptor, when operating at full-speed. Description
4
iConfiguration
3
iConfiguration
2 1 0
iSerialNumber The iSerialNumber string index reported in the device descriptor. iProduct iManufacturer The iProduct string index reported in the device descriptor. The iManufacturer string index reported in the device descriptor.
Document #: 38-08037 Rev. *H
Page 14 of 24
[+] Feedback
CY7C656xx
Byte 22: ActivePorts[3:0] Bits 3-0 are the ActivePorts[3:0] bits that indicates if the corresponding port is usable. For example, a two-port hub that uses ports 1 and 4 would set this field to 0x09. The total number of ports reported in the Hub Descriptor: bNbrPorts field is calculated from this. Default 0x0F Byte 23: RemovablePorts[3:0] Bits 3-0 are the RemovablePorts[3:0] bits that indicates whether the corresponding logical port is removable (set to high). Logical port numbers are from 1 to n where n is the total number of active ports. If port 2 is disabled then physical ports 1, 3, and 4 map to logical ports 1, 2, and 3. These bit values are recorded in the HubDescriptor:DeviceRemovable field. Default 0x0F. Byte 24: LangID Array of LangID codes supported by the hub. Each LangID consists of two bytes, stored LSB first. The array has NumLangs entries (2 * NumLangs bytes). Byte a: iManufacturer Array of addresses for the iManufacturer strings. Each address is two bytes long, stored LSB first. The array has NumLangs entries (2 * NumLangs bytes). (The starting EEPROM address is based upon the number entered for NumLangs. The address a = 24 + 2 * NumLangs. Byte b: iProduct Array of addresses for the iProduct strings. Each address is two bytes long, stored LSB first. The array has Num-
Langs entries (2 * NumLangs bytes). The address b = a + 2 * NumLangs. Byte c: iSerialNumber Array of addresses for the iSerialNumber strings. Each address is two bytes long, stored LSB first. The array has NumLangs entries (2 * NumLangs bytes). The address c = b + 2 * NumLangs. Byte d: iConfiguration(Full-Speed) Array of addresses for the iConfiguration (full-speed) strings. Each address is two bytes long, stored LSB first. The array has NumLangs entries (2 * NumLangs bytes). The address d = c + 2*NumLangs. Byte e: iConfiguration(High-Speed) Array of addresses for the iConfiguration (high-speed) strings. Each address is two bytes long, stored LSB first. The array has NumLangs entries (2 * NumLangs bytes). The address e = d + 2 * NumLangs. Byte f: iInterface(0) Array of addresses for the iInterface(0) strings. Each address is two bytes long, stored LSB first. The array has NumLangs entries (2 * NumLangs bytes). The address f = e + 2 * NumLangs. Byte g: iInterface(1) Reserved Byte h: Strings Strings addressed by the string pointers. Strings must comply with the USB specification. The first byte must be the
Supported USB Requests
Device Class Commands Table 4. Device Class Requests Request
GetDeviceStatus GetInterfaceStatus GetEndpointStatus GetDeviceDescriptor GetConfigDescriptor GetDeviceQualifierDescriptor GetOtherSpeedConfigurationDescriptor GetConfiguration[7] SetCongfiguration[7] GetInterface
bmRequestType bRequest
10000000B 10000001B 10000010B 10000000B 10000000B 10000000B 10000000B 10000000B 00000000B 10000001B 0x00 0x00 0x00 0x06 0x06 0x06 0x06 0x08 0x09 0xA
wValue
0x0000 0x0000 0x0000 0x0001 0x0002 0x0006 0x0007 0x0000 Configuration Value 0x0000
wIndex
0x0000 0x0000 0x0000 Zero or Language ID Zero or Language ID Zero or Language ID Zero or Language ID 0x0000 0x0000 0x0000
wLength
0x0002 0x0002 0x0002
Data
2 Byte Device Status 2 Byte Interface Status 2 Byte Endpoint Status
Descriptor Descriptor Length Descriptor Descriptor Length Descriptor Descriptor Length Descriptor Descriptor Length 0x0001 0x0000 0x0001 Configuration value None Interface Number
Note 7. Only one configuration is supported in CY7C656xx.
Document #: 38-08037 Rev. *H
Page 15 of 24
[+] Feedback
CY7C656xx
Table 4. Device Class Requests (continued) Request
SetInterface SetAddress SetDeviceRemoteWakeup SetDeviceTest_J SetDeviceTest_K SetDeviceTest_SE0_NAK SetDeviceTest_Packet SetEndpointHalt ClearDeviceRemoteWakeup ClearEndpointHalt
bmRequestType bRequest
00000001B 00000000B 00000000B 00000000B 00000000B 00000000B 00000000B 00000000B 00000000B 00000000B 0x0B 0x05 0x03 0x03 0x03 0x03 0x03 0x03 0x01 0x01
wValue
Alternate Setting 0x01 0x02 0x02 0x02 0x02 0x00 0x01 0x00
wIndex
Interface Number 0x0000 0x0100 0x0200 0x0300 0x0400 0x0000 0x0000 0x0000
wLength
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 None None None None None None None None None None
Data
Device Address 0x0000
Hub Class Commands Table 5. Hub Class Requests Request GetHubStatus bmRequestType bRequest 10100000B 0x00 wValue 0x0000 wIndex 0x0000 wLength 0x0004 Data Hub Status (See Table 11-19 of USB 2.0 Specifications) Change Status (See Table 11-20 of USB 2.0 Specifications) Port Status (See Table 11-21 of USB 2.0 Specifications) Change Status (See Table 11-20 of USB 2.0 Specifications) None None
GetPortStatus
10100011B
0x00
0x0000
Byte 0: 0x00 0x0004 Byte 1: Port
ClearHubFeature ClearPortFeature
00100000B 00100011B
0x01 0x01
Feature Selectors[8] 0 or 1
0x0000
0x0000
Feature Byte 0: 0x00 0x0000 Selectors[8] Byte 1: Port 1, 2, 8, 16, 17, 18, 19, or 20 Feature Selectors[8] Byte 0: 22 Byte 1: Port (PORT_INDICATOR) Feature Selector[8] 0 or 1 Feature Selectors[8] 2, 4 or 8 Feature Selector[8] 21 (PORT_TEST) 0x0000 0x0000
ClearPortFeature
00100011B
0x01
None
SetHubFeature
00100000B
0x03
0x0000
SetPortFeature
00100011B
0x03
Port
0x0000
None
SetPortFeature
00100011B
0x03
Byte 0: 0x0000 Selectors[9] 1,2, 3, 4 or 5 Byte 1: Port
None
Notes 8. Feature selector values for different feature is presented in Table 6 on page 17. 9. Selector values for different features are presented in Table 7 on page 17.
Document #: 38-08037 Rev. *H
Page 16 of 24
[+] Feedback
CY7C656xx
Table 5. Hub Class Requests (continued) Request SetPortFeature bmRequestType bRequest 00100011B 0x03 wValue wIndex wLength None Data Byte 0: 0x0000 Feature Selectors[10] Selector[8] 22 (PORT_INDICATOR) 0, 1, 2, or 3 Byte 1: Port Descriptor Type and Descriptor Index Dev_Addr, EP_Num TT_Port 0x0000 TT_Flags 0x0000 Hub Descriptor Length 0x0000 None None TT State None Byte 0: 0x00 0x0000 Byte 1: Port Byte 0: 0x00 TT State Byte 1: Port Length Byte 0: 0x00 0x0000 Byte 1: Port 0x00 Length
GetHubDescriptor
10100000B
0x06
ClearTTBuffer ResetTT GetTTState StopTT Vendor Commands Read EEPROM
00100011B 00100000B 10100011B 00100011B
0x08 0x09 0X0A 0x0B
11000000B
0x02
0x00
Data
This request results in length bytes of data being read from the external memory device, and returned to the host. Data is read beginning with address 0. This request fails if there is no external memory device present. This request is only valid if the hub is in the Configured state; the request fails otherwise. Write EEPROM 01000000B 0x01 0x00 0x00 Length Data This request results in Length bytes of Data being written to the external memory device. Data is written beginning with address 0. This request fails if there is no external memory device present. This request is only valid if the hub is in the Configured state or if the external memory device write protect byte is set; the request fails otherwise. Table 7. Test Mode Selector for Feature Selector PORT_TEST (0x21)[9] Value 0 1 0 1 2 4 8 9 16 17 18 19 20 21 22 PORT_TEST Mode Description Test_J Test_K Test_SE0_NAK Test_Packet Test_Force_Enable Selector Value 1 2 3 4 5 Hub Hub Port Port Port Port Port Port Port Port Port Port Port Port Port
Table 6. Hub Class Feature Selector Feature Selector C_HUB_LOCAL_POWER C_HUB_OVER_CURRENT PORT_CONNECTION PORT_ENABLE PORT_SUSPEND PORT_RESET PORT_POWER PORT_LOW_SPEED C_PORT_CONNECTION C_PORT_ENABLE C_PORT_SUSPEND C_PORT_OVER_CURRENT C_PORT_RESET PORT_TEST PORT_INDICATOR Recipient
Note 10. Selector values for different feature is presented in Table 8 on page 18.
Document #: 38-08037 Rev. *H
Page 17 of 24
[+] Feedback
CY7C656xx
Table 8. Port Indicator Selector for Feature Selector PORT_INDICATOR (0x22) Port Indicator Color Color Set Automatically as shown in Table 1 on page 4 Amber Green Off Selector Value 0 1 2 3 Port Indicator Mode Automatic Mode Manual Mode Manual Mode Manual Mode
Upstream USB Connection
The following is a schematic of the USB upstream connector. Figure 2. USB Upstream Port Connection
VCC D- D+ GND SHELL D- D+ 2.2 F 10V 100 k
BUSPOWER
Downstream USB Connections
The following is a schematic of the USB downstream connector. Figure 3. USB Downstream Port Connection
PWRx VCC
150 F 10V
0.01 F DD-[X]
D-
DD+[X]
D+
GND
SHELL
LED Connections
The following is a schematic of the LED circuitry. Figure 4. USB Downstream Port Connection
3.3V GREEN#[x] 680
AMBER#[x]
680
Document #: 38-08037 Rev. *H
Page 18 of 24
[+] Feedback
CY7C656xx
System Block Diagram
Figure 5. Sample Schematic for 4-Port Self Powered Configuration
5V VCC D- D+ GND SHELL
VBUS
D- 2.2 F 15 k 150 k
VBUSPOWER PWR1 OVR1 DsPWR4 DsPWR1 150 F 10V DD-[1] DD+[1] 0.01 F VCC D- D+ GND SHELL 3.3V GREEN#[1] AMBER#[1] 680
10V
D+
Power
DsPWR3 DsPWR2 DsPWR1
PWR2 Management OVR2 PWR3 OVR3 PWR4 OVR4
680
SPI_SD DO SPI_SCK SPI_CS DI CLK CS SPI_SD 150 F 10V DsPWR2 DD-[2] DD+[2] 0.01 F VCC D- D+ GND SHELL 3.3V
SPI EEPROM 24 MHz 3.3V 3.3V 12 pF 12 pF
GREEN#[2] AMBER#[2]
680
680
XIN
10K
SELFPWR VBUSPOWER 3.3V 100K RESET 0.1F D- D+ DD-[1] DD+[1] DD-[2] DD+[2] DD-[3] DD+[3] DD-[4] DD+[4] DD+ DD-[1] DD+[1] DD-[2] DD+[2] DD-[3] DD+[3] DD-[4] DD+[4] GND1 GND2 GND3 GND4 GND5 GND6 GND7 GND8 GND9 GND10 GND11 GND12 VBUSPOWER GREEN[1] AMBER[1] GREEN[2] AMBER[2] GREEN[3] AMBER[3] GREEN[1] AMBER[1] GREEN[2] AMBER[2] GREEN[3] AMBER[3] GREEN[4] AMBER[4] PWR1 OVR1 PWR2 OVR2 PWR3 OVR3 PWR4 OVR4 SPI_CS SPI_SCK SPI_SD
VCC1 VCC2 VCC3 VCC4 VCC5 VCC6 VCC7 VCC8 VCC9 VCC10 VCC11
XOUT
DsPWR3 150 F 10V DD-[3] DD+[3] 0.01 F
VCC D- D+ GND SHELL 3.3 V
HX2LP
GREEN[4] AMBER[4] PWR1 OVR1 PWR2 OVR2 PWR3 OVR3 PWR4 OVR4 SPI_CS SPI_SCK SPI_SD
GREEN#[3] AMBER#[3]
680
680
DsPWR4 150 F 10V DD-[4] DD+[4] 0.01 F
VCC D- D+ GND SHELL 3.3 V
GREEN#[4] AMBER#[4]
680
680
Document #: 38-08037 Rev. *H
Page 19 of 24
[+] Feedback
CY7C656xx
Electrical Characteristics
Absolute Maximum Ratings Storage Temperature ................................ -65C to +150 C Ambient Temperature with Power Applied: Commercial.................... 0C to +70C Automotive ................. -40C to +85C Supply Voltage to Ground Potential .............. -0.5V to +4.0V DC Voltage Applied to Outputs in High Z State ...............................................................-0.5V to VCC + 0.5V Power Dissipation (4 HS ports) .....................................0.9 W Static Discharge Voltage ...........................................> 2000V Max. Output Sink Current per I/O ................................10 mA DC Electrical Characteristics Parameter VCC VIH VIL Il VOH VOL IOH IOL CIN ISUSP ICC Description Supply Voltage Input High Voltage Input Low Voltage Input Leakage Current Output Voltage High Output Low Voltage Output Current High Output Current Low Input Pin Capacitance Suspend Current Supply Current 4 Active ports Full-speed Host, Full-speed Devices High-speed Host, High-speed Devices High-speed Host, Full-speed Devices 2 Active Ports Full-speed Host, Full-speed Devices High-speed Host, High-speed Devices High-speed Host, Full-speed Devices No Active Ports Full-speed Host High-speed Host USB Transceiver USB 2.0 certified in full-, low-, and high-speed modes. AC Electrical Characteristics Both the upstream USB transceiver and all four downstream transceivers have passed the USB-IF USB 2.0 Electrical Certification Testing. 86 231 154 77 163 136 65 93 110 260 180 100 190 160 90 120 mA mA mA mA mA mA mA mA 80 0 < VIN < VCC IOUT = 4 mA IOUT = -4 mA 2.4 0.4 4 4 10 Conditions Min. 3.15 2 -0.5 Typ. 3.3 Max. 3.45 18 5.25 0.8 10 Unit V V/ms V V A V V mA mA pF A Operating Conditions TA (Ambient Temperature Under Bias) Commercial ........ 0C to +70C Automotive ..... -40C to +85C Supply Voltage............................................+3.15V to +3.45V Ground Voltage.................................................................. 0V FOSC (Oscillator or Crystal Frequency)...... 24 MHz 0.05% parallel resonant, fundamental mode, 12-pF load capacitance, 0.5 mW
VCC RampUp Ramp rate on VCC
Document #: 38-08037 Rev. *H
Page 20 of 24
[+] Feedback
CY7C656xx
Serial Peripheral Interface Parameter Description Clock Rise/Fall Time Clock Frequency Data Set-up Time Hold Time Reset Period 50 100 1.9 Conditions Min. Typ. Max. 500 250 Unit ns KHz ns ns ms
Ordering Information
Ordering Code CY7C65630-56LFXC CY7C65630-56LFXA CY7C65620-56LFXC CY4606 CY4605 56-pin QFN 4-Port 56-pin QFN 4-Port Automotive AEC grade 56-pin QFN 2-Port CY7C65630 USB 2.0 4-Port Hub Reference Design Kit CY7C65620 USB 2.0 2-Port Hub Reference Design Kit Package Type
Document #: 38-08037 Rev. *H
Page 21 of 24
[+] Feedback
CY7C656xx
Package Diagram
The CY7C656xx is available in a space saving 56-pin QFN (8 x 8 mm) Figure 6. 56-Lead QFN 8 x 8 MM LF56A (Subcon Punch Type with 6.1 x 6.1 EPAD)
51-85144 *G
Windows is a registered trademark of Microsoft Corporation. TetraHub and EZ-USB HX2LP are trademarks of Cypress Semiconductor Corporation. All product and company names mentioned in this document are trademarks of their respective holders.
Document #: 38-08037 Rev. *H
Page 22 of 24
(c) Cypress Semiconductor Corporation, 2006-2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
CY7C656xx
Document History Page
Document Title: CY7C656xx EZ-USB HX2LPTM Low-Power USB 2.0 Hub Controller Family Document Number: 38-08037 REV. ** *A ECN NO. Issue Date 131505 231329 02/12/2004 See ECN Orig. of Change JTC KKU New Data Sheet Changed load capacitors to 12 pF, updated part numbers, added functional overviews, block descriptions, pin configurations, default descriptors, configurations options, supported USB requests, electrical characteristics and package diagram Added typical values for Icc in the DC Electrical Characteristics table, changed MPN CY7C65650 to CY7C65640B, added CY7C65620 package Added Reset period in to the table in section `Serial Peripheral Interface' Added 0xD4 EEPROM Load Added vendor command values Added VCC ramp rate Updated block diagram Updated features list Removed from the Enumeration section "Once the hub is configured, the full hub functionality is available" Added reference to 0xD4 load to the Downstream Ports section Added reference to polarity control in the Power Switching and Over-current Detection sections Updated the Automatic Port State to Port Indicator Color Mapping table to match USB-IF spec changes Added LED modulation to the Port Indicators section Updated pin description table - SELFPWR# to SELFPWR and removed references to limitations of bus powered. Added reference to polarity control on PWR#, OVR# and LED control lines Updated Default descriptors Updated EEPROM list to include 25LC080 Removed NoEOPatEOF1 bit Added LED polarity control Removed all references to HX1TT and Multi-TT Updated Block Diagrams to remove ports and TTs Removed Preliminary Updated Device ID default Added Write Protect Description Correct sample schematics to reflect latest RDK Updated Power Consumption Numbers Updated Part Numbers Corrected typo in Table 3. Changed downstream port 4 signal labels from [3] to [4]. Added dimensions of E-Pads to Figure 6. changed feature "2-Port Single TT for bus power support" to "Bus powered configurations" updated figure 5. Added blank EEPROM statement to the Device Descriptor section Added blank EEPROM statement to the Configuration Options section Added indicator for factory fusable options. Description of Change
*B *C
250869 330195
See ECN See ECN
ARI KKU
*D
342997
See ECN
KKU
*E
498396
See ECN
TEH
*F *G
570287 852600
See ECN See ECN
ARI KKU
Document #: 38-08037 Rev. *H
Page 23 of 24
[+] Feedback
CY7C656xx
Document Title: CY7C656xx EZ-USB HX2LPTM Low-Power USB 2.0 Hub Controller Family Document Number: 38-08037 REV. *H ECN NO. Issue Date 1019740 See ECN Orig. of Change Description of Change
KKU/ARI Added to Features: Automotive AEC grade option (-40-85C). Added to Part numbers: CY7C65630-56LFXA: 56-pin QFN 4-Port Automotive AEC grade. Added absolute ambient temperature with power applied for automotive part. Added operational Ambient Temperature Under Bias for automotive part. Replaced TBD under absolute maximum power dissipation with 0.9 Watts. Removed internal part numbers referenced in figure 6 note 5. Changed "USB 2.0-Compliant" to "USB 2.0-Certified" RemovablePorts updated to reflect logical ports. Edited for active voice.
Document #: 38-08037 Rev. *H
Page 24 of 24
[+] Feedback


▲Up To Search▲   

 
Price & Availability of CY7C65630-56LFXA

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X