View ST380CHPBF_1317440.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Bulletin I25227 09/06
ST380CHPBF SERIES
PHASE CONTROL THYRISTORS Hockey Puk Version
Features
Center amplifying gate Metal case with ceramic insulator International standard case TO-200AB (E-PUK) Low profile hockey-puk to increase current-carrying capability Extended temperature range Lead Free
960A
Typical Applications
DC motor controls Controlled DC power supplies AC controllers
Major Ratings and Characteristics
Parameters
IT(AV) @ Ths IT(RMS) @ Ths ITSM @ 50Hz @ 60Hz I2 t @ 50Hz @ 60Hz V DRM/V RRM tq TJ typical
case style TO-200AB (E-PUK)
Units
A C A C A A KA2s KA2s V s C
ST380CH..C
960 80 2220 25 12500 13000 782 713 400 to 600 100 - 40 to 150
www.irf.com
1
ST380CHPBF Series
Bulletin I25227 09/06
ELECTRICAL SPECIFICATIONS Voltage Ratings
Voltage Type number Code
04 ST380CH..C 06
V DRM/V RRM, max. repetitive peak and off-state voltage V
400 600
VRSM , maximum nonrepetitive peak voltage V
500 700
I DRM/I RRM max.
@ TJ = TJ max
mA
100
On-state Conduction
Parameter
I T(AV) Max. average on-state current @ Heatsink temperature I T(RMS) Max. RMS on-state current cooled I TSM Max. peak, one-cycle non-repetitive surge current 12500 13000 10500 11000 It
2
ST380CH..C
960 (440) 80 (110) 2220
Units Conditions
A C 180 conduction, half sine wave double side (single side) cooled DC @ 25C heatsink temperature double side
t = 10ms A t = 8.3ms t = 10ms t = 8.3ms KA2s t = 10ms t = 8.3ms t = 10ms t = 8.3ms KA s
2
No voltage reapplied 100% VRRM reapplied No voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial TJ = TJ max.
Maximum I t for fusing
2
782 713 553 505
I t
2
Maximum I t for fusing
2
V T(TO)1 Low level value of threshold voltage V T(TO)2 High level value of threshold voltage r t1 r t2 VTM IH IL Low level value of on-state slope resistance High level value of on-state slope resistance Max. on-state voltage Maximum holding current Typical latching current
7820 0.85
t = 0.1 to 10ms, no voltage reapplied (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. (I > x IT(AV)),TJ = TJ max. (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max.
V 0.88
0.25 m 0.24
(I > x IT(AV)),TJ = TJ max.
1.58 600 1000
V mA
I = 2900A, TJ = TJ max, t = 10ms sine pulse pk p T J = 25C, anode supply 12V resistive load
Switching
Parameter
di/dt Max. non-repetitive rate of rise of turned-on current td tq Typical delay time Typical turn-off time
ST380CH..C
1000 1.0
Units Conditions
A/s Gate drive 20V, 20, t 1s
r
TJ = TJ max, anode voltage 80% VDRM Gate current 1A, di g /dt = 1A/s Vd = 0.67% VDRM, TJ = 25C ITM = 550A, TJ = TJ max, di/dt = 40A/s, VR = 50V dv/dt = 20V/s, Gate 0V 100, tp = 500s
s 100
2
www.irf.com
ST380CHPBF Series
Bulletin I25227 09/06
Blocking
Parameter
dv/dt I RRM I DRM Maximum critical rate of rise of Max. peak reverse and off-state leakage current
ST380CH..C
500 off-state voltage 100
Units Conditions
V/s mA TJ = TJ max. linear to 80% rated VDRM TJ = TJ max, rated V DRM/V RRM applied
Triggering
Parameter
PGM Maximum peak gate power
ST380CH..C
10.0 2.0 3.0 20
Units Conditions
W A TJ = TJ max, t p 5ms TJ = TJ max, f = 50Hz, d% = 50 TJ = TJ max, t p 5ms
P G(AV) Maximum average gate power IGM +VGM -VGM Max. peak positive gate current Maximum peak positive gate voltage Maximum peak negative gate voltage TYP. 200 IGT DC gate current required to trigger 100 40 2.5 VGT DC gate voltage required to trigger I GD VGD DC gate current not to trigger DC gate voltage not to trigger 1.8 1.0
V 5.0 MAX. 200 3.0 10 0.25 mA V V mA
TJ = TJ max, t 5ms
p
TJ = - 40C TJ = 25C TJ = 150C TJ = - 40C TJ = 25C TJ = 150C Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied
TJ = TJ max
Thermal and Mechanical Specification
Parameter
TJ Tstg Max. operating temperature range Max. storage temperature range
ST380CH..C
-40 to 150 -40 to 150 0.09 0.04 0.02 0.01 9800 (1000)
Units Conditions
C DC operation single side cooled K/W DC operation double side cooled DC operation single side cooled DC operation double side cooled N (Kg) g See Outline Table
R thJ-hs Max. thermal resistance, junction to heatsink R thC-hs Max. thermal resistance, case to heatsink F Mounting force, 10%
K/W
wt
Approximate weight Case style
83
TO - 200AB (E-PUK)
www.irf.com
3
ST380CHPBF Series
Bulletin I25227 09/06
RthJ-hs Conduction
(The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC)
Conduction angle
180 120 90 60 30
Sinusoidal conduction
0.010 0.012 0.015 0.022 0.036 0.011 0.012 0.015 0.022 0.036
Rectangular conduction
0.007 0.012 0.016 0.023 0.036 0.007 0.013 0.017 0.023 0.037
Units
Conditions
TJ = TJ max.
Single Side Double Side Single Side Double Side
K/W
Ordering Information Table
Device Code
ST
1
38
2
0
3
CH
4
06
5
C
6
1
7 8
PbF
9
1 2 3 4 5 6 7
-
Thyristor Essential part number 0 = Converter grade CH = Ceramic Puk, High temperature Voltage code: Code x 100 = VRRM (See Voltage Rating Table) C = Puk Case TO-200AB (E-PUK) 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads)
8
-
Critical dv/dt: None = 500V/sec (Standard selection) L = 1000V/sec (Special selection)
9
-
Lead Free
4
www.irf.com
ST380CHPBF Series
Bulletin I25227 09/06
Outline Table
ANODE TO GATE CREEPAGE DISTANCE: 11.18 (0.44) MIN. STRIKE DISTANCE: 7.62 (0.30) MIN. 25.3 (0.99) DIA. MAX. 0.3 (0.01) MIN.
14.1 / 15.1 (0.56 / 0.59) 0.3 (0.01) MIN. 25.3 (0.99) DIA. MAX. GATE TERM. FOR 1.47 (0.06) DIA. PIN RECEPTACLE
40.5 (1.59) DIA. MAX.
2 HOLES 3.56 (0.14) x 1.83 (0.07) MIN. DEEP 6.5 (0.26) 4.75 (0.19)
Case Style TO-200AB (E-PUK)
All dimensions in millimeters (inches)
25 5
42 (1.65) MAX. 28 (1.10)
Quote between upper and lower pole pieces has to be considered after application of Mounting Force (see Thermal and Mechanical Specification)
Maximum Allowable Heatsink T emperature (C)
Maximum Allowable Heatsink T emperature (C)
150 140 130 120 110 100 90 80 70 60 50 40 0
150 140 130 120 110 100 90 80 70 60 50 40 30 20 0 200 400 30
S 380CH..C S T eries (S ingle S Cooled) ide RthJ-hs (DC) = 0.09 K/ W
S 380CH..C S T eries (S ingle S ide Cooled) R thJ-hs (DC) = 0.09 K/ W
Conduc tion Angle
Conduc tion Period
30
60 90 120 180
60 90 120 600
180
DC
100 200 300 400 500 600 700 800 Average On-s tate Current (A)
Fig. 1 - Current Ratings Characteristics
800 1000 1200 1400
Average On-state Current (A)
Fig. 2 - Current Ratings Characteristics
www.irf.com
5
ST380CHPBF Series
Bulletin I25227 09/06
Maximum Allowable Heatsink Temperature (C)
Ma ximum Allowab le Heatsink T emperature (C)
150 140 130 120 110 100 90 80 70 60 50 40 30 20 0 400 30
150 140 130 120 110 100 90 80 70 60 50 40 30 20 0 500
S 380CH..C S T eries (Double S Cooled) ide RthJ-hs (DC) = 0.04 K/ W
S 380CH..C S T eries (Double S Cooled) ide RthJ-hs (DC) = 0.04 K/ W
Conduction Angle
Conduc tion Period
30 60 90 120 180 DC 1000 1500 2000 2500
60
90 120 180
800
1200
1600
Average On-state Current (A)
Fig. 3 - Current Ratings Characteristics
Average On-state Current (A)
Fig. 4 - Current Ratings Characteristics
Maximum Average On-state Power Loss (W)
2500 180 120 90 60 30
Maximum Average On-s tate P ower Loss (W)
3500 3000 2500 2000 RMS Limit 1500
Conduc tion Period
2000
RMS Limit
1500
DC 180 120 90 60 30
1000
Conduction Angle
1000 500 0 0 500 1000 1500 2000 2500 Average On-state Current (A)
Fig. 6- On-state Power Loss Characteristics
500
S 380CH..C S T eries T = 150C J 0 400 800 1200 1600
S 380CH..C S T eries TJ = 150C
0 Average On-state Current (A)
Fig. 5- On-state Power Loss Characteristics
Peak Half Sine Wave On-s tate Current (A)
Peak Half S Wave On-state Current (A) ine
12000 11000 10000 9000 8000 7000 6000 5000 1
At Any R ated Load Condition And With Rated VRRM Applied Following S urge. Initial T = 150C J @60 Hz 0.0083 s @50 Hz 0.0100 s
13000
Maximum Non Repetitive S urge Current Versus Puls T e rain Duration. Control 12000 Of Conduc tion May Not Be Maintained. Initial T = 150C J 11000 No Voltage Reapplied Rated VRRM Reapplied 10000 9000 8000 7000 6000 S 380CH..C S T eries
S 380CH..C S T eries
10
100
5000 0.01
0.1 Puls T e rain Duration (s)
1
Number Of Equal Amplitude Half Cycle Current Pulses (N)
Fig. 7 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled
Fig. 8 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled
6
www.irf.com
ST380CHPBF Series
Bulletin I25227 09/06
10000 Instantaneous On-state Current (A) T = 25C J T = 150C J
1000
S 380CH..C S T eries
100 0.5
1
1.5
2
2.5
3
3.5
Instantaneous On-state Voltage (V)
Fig. 9 - On-state Voltage Drop Characteristics
T ransient T hermal Impedanc e ZthJ-hs (K/W) 0.1 S 380CH..C S T eries
0.01
S teady S tate Value R thJ-hs = 0.09 K/ W (S ingle S ide Cooled) R thJ-hs = 0.04 K/ W (Double S ide Cooled) (DC Operation)
0.001 0.001
0.01
0.1 S quare Wave Pulse Duration (s)
1
10
Fig. 10 - Thermal Impedance ZthJ-hs Characteristics
100 Instantaneous Gate Voltage (V) R tangular gate pulse ec a) Recommended load line for rated di/ dt : 20V, 10ohms; tr<=1 s b) Recommended load line for 10
<=30% ra ted d i/ dt : 10V, 10ohms
(1) PGM = 10W, tp (2) PGM = 20W, tp (3) PGM = 40W, tp (4) PGM = 60W, tp (a) (b)
T j=-40 C
= 4ms = 2ms = 1ms = 0.66ms
tr<=1 s
T j=25 C
T j=150 C
1 VGD IGD 0.1 0.001 0.01
(1)
(2)
(3) (4)
Device: S 380CH..C S T eries 0.1 1
F requency Limited by PG(AV) 10 100
Insta ntaneous Gate Current (A)
Fig. 11 - Gate Characteristics
www.irf.com
7
ST380CHPBF Series
Bulletin I25227 09/06
Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level. Qualification Standards can be found on IR's Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 09 /06
8
www.irf.com

▲Up To Search▲

Price & Availability of ST380CHPBF

	To Download ST380CHPBF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .