![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
ST26C32A CMOS quad tri-state differential line receiver General features s s CMOS design for low power 0.2V sensitivity over input common mode voltage range Typical propagation delay: 19ns Typical input hysteresis: 60mV Input will not load line when VCC = 0V Meets the requirements of EIA standard RS-422, RS-423 3-state outputs for connection to system buses Available in surface mount TSSOP16 DIP-16 SO-16 s s s s s s Description The ST26C32A is a quad differential line receiver designed to meet the RS-422, RS-423 standards for balanced and unbalanced digital data transmission, while retaining the low power characteristics of CMOS. The ST26C32A has an input sensitivity of 200mV over the common mode input voltage range of 7V. The ST26C32A features internal pull-up and pull-down resistors which prevent output oscillation on unused channels. The ST26C32A provides an enable and disable function to all four receivers and features 3-STATE output with 6mA source and sink capability. Order code Part number ST26C32ABN ST26C32ABDR ST26C32ABTR Temperature range -40 to 85 C -40 to 85 C -40 to 85 C Package DIP-16 SO-16 (Tape & Reel) TSSOP16 (Tape & Reel) Packaging 25 parts per tube / 40 tube per box 2500 parts per reel 2500 parts per reel May 2006 Rev 3 1/15 www.st.com 15 Contents ST26C32A Contents 1 2 3 4 5 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2/15 ST26C32A Pin configuration 1 Figure 1. Pin configuration Pin connections Table 1. Pin n 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Pin description Symbol AIN1 AIN2 AOUT EN BOUT BIN2 BIN1 GND CIN1 CIN2 COUT EN DOUT DIN2 DIN1 VCC INPUT A1 INPUT A2 Channel A Output ENABLE Channel B Output INPUT B2 INPUT B1 Ground INPUT C1 INPUT C2 Channel C Output ENABLE Channel D Output INPUT D2 INPUT D1 Supply Voltage Name and function 3/15 Pin configuration ST26C32A Table 2. Truth table Enable L Enable H Input X VID VTH(MAX) All other combinations of enable inputs VID VTH(MIN) Open Output Z H L H Note: L = Low Voltage State H = High Logic State X = Don't Care Z = High Impedance 4/15 ST26C32A Maximum ratings 2 Table 3. Symbol VCC VCM VDIFF VIN IOMAX Tstg Maximum ratings Absolute maximum ratings (Note: 1, Note 2) Parameter Supply voltage Input common mode range Differential input voltage Enable input voltage Maximum current per output Storage temperature range Value 7 14 14 7 25 -65 to +150 Unit V V V V mA C Note: 1 Absolute Maximum Ratings are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The table of electrical characteristics provide conditions for actual device operation. Unless otherwise specified, all voltage are referenced to ground. All currents into the device pins are positive; all currents out of the device pins are negative. Recommended operating conditions Parameter Supply voltage Operating temperature range Maximum enable input rise or fall times Value 4.5 to 5.5 -40 to +85 500 Unit V C ns 2 Table 4. Symbol VCC TA tr, tf 5/15 Electrical characteristics ST26C32A 3 Table 5. Electrical characteristics Electrical characteristics (VCC = 5V 10%, unless otherwise specified, See Note: 1) Value Parameter Minimum differential input voltage Input resistance Input current High level output voltage Low level output voltage Minimum enable high input level voltage Minimum enable low input level voltage 3-STATE Output leakage current Maximum enable input current Quiescent power supply current Input hysteresis VOUT = VCC or GND ENABLE = VIL, ENABLE = VIH VIN = VCC or GND VCC = Max, V(DIFF) = 1V VCM = 0V 16 60 0.5 Test Conditions Min. VTH RIN IIN VOH VOL VIH VIL IOZ II ICC VHYST VOUT = VOH or VOL, -7V < VCM < 7V VIN = -7V, 7V, other input = GND VIN = 10V, other input = GND VIN = -10V, other input = GND VDIFF = 1V, IOUT = -6mA VDIFF = -1V, IOUT = 6mA 2 0.8 5 1 23 3.8 -200 5 Typ. 35 6.8 1.1 -2 4.2 0.2 0.3 Max. 200 10 1.5 mA -2.5 V V V V A A mA mV mV K Unit Symbol Note: 1 Unless otherwise specified, min/max limits apply across the recommended operating temperature range. All typical are given for VCC = 5V and TA = 25C 6/15 ST26C32A Table 6. Symbol tPLH tPHL tRISE tFALL tPZH tPZL tPHZ tPLZ DR Electrical characteristics Switching characteristics (VCC = 5V 10%, see Note 1) Value Parameter Test Conditions Min. Propagation delay input to CL = 50pF, VDIFF = 2.5V, VCM = 0V output Output rise and fall times Propagation enable time to output Propagation disable time to output Data rate CL = 50pF, VDIFF = 2.5V, VCM = 0V CL = 50pF, VDIFF = 2.5V, RL = 1000 CL = 50pF, VDIFF = 2.5V, RL = 1000 VDIFF = 2.5V CL = 50pF All outputs loaded and switching 10 Typ. 19 4 13 13 20 Max. 30 9 23 22 ns ns ns ns Mbits/s Unit Note: 1 Unless otherwise specified, min/max limits apply across the recommended operating temperature range. All typical are given for VCC=5V and TA = 25C 7/15 Package mechanical data ST26C32A 4 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 8/15 ST26C32A Package mechanical data Plastic DIP-16 (0.25) MECHANICAL DATA mm. DIM. MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.27 8.5 2.54 17.78 7.1 5.1 0.130 0.050 0.51 0.77 0.5 0.25 20 0.335 0.100 0.700 0.280 0.201 1.65 TYP MAX. MIN. 0.020 0.030 0.020 0.010 0.787 0.065 TYP. MAX. inch P001C 9/15 Package mechanical data ST26C32A SO-16 MECHANICAL DATA DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 8 (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45 (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.25 1.64 0.46 0.25 0.013 0.007 0.019 0.004 MIN. inch TYP. MAX. 0.068 0.010 0.063 0.018 0.010 0016020D 10/15 ST26C32A Package mechanical data TSSOP16 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0 0.45 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC inch MAX. 1.2 0.15 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8 0.75 0 0.018 TYP MIN. TYP. MAX. 0.047 0.004 0.039 0.006 0.041 0.012 0.0079 0.201 0.260 0.176 1 1.05 0.30 0.20 5.1 6.6 4.48 8 0.030 0.60 0.024 A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 11/15 Package mechanical data ST26C32A Tape & Reel SO-16 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.45 10.3 2.1 3.9 7.9 12.8 20.2 60 22.4 6.65 10.5 2.3 4.1 8.1 0.254 0.406 0.082 0.153 0.311 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.262 0.414 0.090 0.161 0.319 MIN. TYP. MAX. 12.992 0.519 inch 12/15 ST26C32A Package mechanical data Tape & Reel TSSOP16 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.7 5.3 1.6 3.9 7.9 12.8 20.2 60 22.4 6.9 5.5 1.8 4.1 8.1 0.264 0.209 0.063 0.153 0.311 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.272 0.217 0.071 0.161 0.319 MIN. TYP. MAX. 12.992 0.519 inch 13/15 Revision history ST26C32A 5 Table 7. Date Revision history Revision history Revision 3 Changes Order codes has been updated and new template. 02-May-2006 14/15 ST26C32A Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 15/15 |
Price & Availability of ST26C32ABTR
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |