View RF217506_1301285.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

RF2175
0
Typical Applications * 3V TETRA Cellular Handsets * 3V CDMA Cellular Handsets * Portable Battery-Powered Equipment
3V 400MHz LINEAR AMPLIFIER
Product Description
The RF2175 is a high-power, high-efficiency linear amplifier IC targeting 3V handheld systems. The device is manufactured on an advanced Gallium Arsenide Heterojunction Bipolar Transistor (HBT) process, and has been designed for use as the final RF amplifier in TETRA handheld digital cellular equipment, spread-spectrum systems, and other applications in the 380MHz to 512MHz band. The RF2175 has an analog bias control voltage to maximize efficiency. The device is self-contained with 50 input, and the output can be easily matched to obtain optimum power, efficiency, and linearity characteristics. The package is a small SSOP-16 plastic with backside ground.
-A0.154 0.012 0.008 0.004 0.002 Note 3
EXPOSED HEATSINK
Exposed Heat Sink
0.196 0.189
0.025
0.123 0.107
0.237
0.063 0.057
0.087 0.071
8 MAX 0 MIN
NOTES: 1. Shaded lead in Pin 1. 2. Lead coplanarity - 0.003 with respect to datum "A". 3. Lead standoff is specified from the lowest point on the package underside. 0.035 0.016 0.010 0.007
Optimum Technology Matching(R) Applied
Si BJT Si Bi-CMOS InGaP/HBT GaAs HBT SiGe HBT GaN HEMT GaAs MESFET Si CMOS SiGe Bi-CMOS
Package Style: SSOP-16 Slug
Features * Single 3V Supply * 31.8dBm Linear Output Power * 37.5dB Linear Gain * 30% Linear Efficiency * On-Board Power Down Mode * 380MHz to 512MHz Operation
VCC LTUNE NC Q1C GND1 RF IN
1 2 3 4 5 6 7 Bias
16 15 14 13 12 11 10 9
VBIAS
RF OUT RF OUT RF OUT
Ordering Information
RF2175 RF2175 PCBA 3V 400MHz Linear Amplifier Fully Assembled Evaluation Board
VREG
8
Functional Block Diagram
RF Micro Devices, Inc. 7628 Thorndike Road Greensboro, NC 27409, USA
Tel (336) 664 1233 Fax (336) 664 0454 http://www.rfmd.com
Rev A8 030313
2-287
RF2175
Absolute Maximum Ratings Parameter
Supply Voltage (RF Off) Supply Voltage (RF Applied) Mode Voltage (VBIAS) Control Voltage (VREG) Input RF Power (Avg.) Output VSWR - Inband Output VSWR - Out of Band Operating Ambient Temperature Storage Temperature Moisture Sensitivity
Rating
+8.0 +4.5 +5.0 +5.0 +5 6:1 20:1 -30 to +100 -40 to +120 JEDEC Level 5 *
Unit
VDC VDC VDC VDC dBm
Caution! ESD sensitive device.
RF Micro Devices believes the furnished information is correct and accurate at the time of this printing. However, RF Micro Devices reserves the right to make changes to its products without notice. RF Micro Devices does not assume responsibility for the use of the described product(s).
C C
Parameter
Overall
Usable Frequency Range Typical Frequency Range Linear Gain Harmonic P3dB Output Power Linear Output Power (TETRA Modulation) Total Linear Efficiency Adjacent Channel Power Rejection
Specification Min. Typ. Max.
Unit
Condition
T=25C, VCC =3.6V, Freq=410MHz to 420MHz unless otherwise specified, 25% duty cycle. POUT =31.8dBm
380 34.5 34 31.8 25 -35 -45 30 410 to 420 37.5
512 41.5 -30
MHz MHz dB dBc dBm dBm % dBc dBc
ACPR@25kHz, TETRA modulation ACPR@50kHz, TETRA modulation
Power Supply
Power Supply Voltage Idle Current VCC Current VREG Current VBIAS Current Turn On/Off Time 3.0 3.6 230 4.5 450 1650 13 3 <150 V mA mA mA mA s All VCC pins, no RF input. All VCC pins, POUT =31.8dBm Pin 8 Pin 16 Time for power to rise to 95% of its final value. Measured with 4.7F and 2.2F capacitors on both VREG and VBIAS lines. VREG =Low
Total Current (Power Down) 10 A 0 0.2 V VREG "Low" Voltage 2.7 2.8 2.9 V VREG "High" Voltage 2.8 2.9 V VBIAS Control Voltage Range * The RF2175 is considered JEDEC Level 5 for moisture sensitivity with a maximum peak reflow temperature of 220C. To assure reliable performance, this part must be handled in accordance with JEDEC specifications for a Level 5 part.
2-288
Rev A8 030313
RF2175
Pin 1 2 3 4 5 6 7 8 Function VCC L TUNE NC Q1C GND1 RF IN NC VREG Description
Power supply for input bias circuitry. A 1nF high frequency bypass capacitor is recommended. Interstage Tuning. A shunt inductor to GND is required to optimize the match. No connection. Power supply for stage 1. VCC should be fed through a 25nH or greater inductor with a decoupling capacitor on the VCC side. Ground for stage 1. For best performance, keep traces physically short and connect immediately to ground plane. This ground should be isolated from the backside ground contact. RF input. An external DC blocking capacitor is required if this port is connected to a DC path to ground or a DC voltage. No connection. Power Down control. When this pin is "low", all circuits are shut off. When this pin is 2.8V, all circuits are operating normally. VPD requires a regulated 2.8V for the amplifier to operate properly over all specified temperature and voltage ranges. A dropping resistor from a higher regulated voltage may be used to provide the required 2.8V. A 100pF high frequency bypass capacitor is recommended. No connection. No connection. No connection. RF output and power supply for the output stage. The bias for the output stage is provided through this pin and pin 13. An external matching network is required to provide the optimum load impedance; see the application schematics for details. Same as pin 12. Harmonic trap. This pin connects to the RF output but is used for providing a low impedance to the second harmonic of the operating frequency. An inductor or transmission line resonating with a shunt capacitor at 2f0 is connected to this pin. No connection. The bias pin allows higher efficiency in low power power modes. When operating at full output, VBIAS should be 2.8V. Ground connection. The backside of the package should be soldered to a top side ground pad, which is connected to the ground plane with multiple vias. The pad should have a short thermal path to the ground plane.
Interface Schematic
9 10 11 12
NC NC NC RF OUT
13 14
RF OUT RF OUT
15 16 Pkg Base
NC VBIAS GND
Rev A8 030313
2-289
RF2175
Application Schematic 380MHz
VCC = 3.0 V to 5.2 V
VCC 0 2.2 uF 1 nF 1 56 nH 5.1 nH 3 4 5
RF IN: TETRA Modulation
33 nH VMODE 100 pF 16 Bias 15 5.6 nH 14 3.6 nH 13 12 11 10 9 12.55 nH 56 pF 12 pF VCC 1 nF RF OUT 5.6 pF 2.2 uF 4.7 F
2
1 nF 6 7 33 nH
RF IN
100 pF
VREG 4.7 pF 2.2 uF 100 pF
8
VREG (VACP) = 2.6 V on, 0 V off 25% duty cycle, 14.17 ms pulse width
2-290
Rev A8 030313
RF2175
Evaluation Board Schematic
(Download Bill of Materials from www.rfmd.com.)
L2 33 nH VCC R1 0 C2 2.2 uF C3 1 nF 1 L4 56 nH 2 L5 4.7 nH 3 4 C6 1 nF 5 6 7 8 C16 4.7 pF C5 2.2 uF C8 100 pF
2175400A
VMODE C15 100 pF 16 Bias 15 14 13 12 11 10 9 L6 12.55 nH VCC L3 33 nH C4 100 pF C9 56 pF C10 12 pF C13 5.1 pF L1 3.6 nH C11 1 nF 50 strip C14 2.2 uF C17 4.7 F
L7 5.6 nH
J2 RF OUT
J1 RF IN
50 strip
VREG
P1 P1-1 1 2 P1-3 3 CON3 VCC GND VREG P2-3 P2-1
P2 1 2 3 CON3 VCC GND VMODE
Rev A8 030313
2-291
RF2175
Evaluation Board Layout Board Size 2.0" x 2.0"
Board Thickness 0.028", Board Material FR-4
2-292
Rev A8 030313

▲Up To Search▲

Price & Availability of RF217506

	To Download RF217506 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .