View MA4FCP200_1271450.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MA4FCP200
Silicon Flip Chip PIN Diode
Features
* * * * * * * * Low Series Resistance Low Capacitance High Cut-off Frequency Silicon Nitride Passivation Polyimide Scratch Protection Designed for Automated Pick and Place Insertion Rugged by Design Surface Mountable
Case Style ODS-12641, 2, 3
B G E
A C D
Description
M/A-COM's MA4FCP200 series is a silicon flip chip PIN diode fabricated with M/A-COM's patented HMICTM process. This diode is fabricated on epitaxial wafers using a process designed for repeatable electrical characteristics and extremely low parasitics. This diode is fully passivated with Silicon Nitride and has an additional layer of Polyimide for scratch protection. These protective coatings prevent damage to the junction during automated or manual handling. This flip chip configuration is suitable for pick and place insertion.
1. 2. 3.
Dimensions are in inches, () are in mm. Unless otherwise noted, tolerance are inches + .001" (millimeters + .025 mm). Schematic is for junction side up.
DIM. A B C D E F G
INCHES MIN. MAX. 0.0082 0.0092 0.0141 0.0151 0.0035 Typ. .00038 0.0048 0.0085 0.0095 0.0023 0.0033 0.0048 0.0058 Units pF pF

MILLIMETERS MIN. MAX. 0.209 0.233 0.359 0.383 0.090 Typ. 0.097 0.121 0.217 0.240 0.059 0.083 0.123 0.147 Typ. 0.020 0.015 2.4 2.8 1.25 1.50 Max. 0.030
Electrical Specifications @ +25C
Symbol CT CT RS RS VF VR IR RJL TL
1. 2. 3. 4.
Parameter Total Capacitance Total Capacitance Series Resistance Series Resistance Forward Voltage Reverse Voltage Reverse Current Thermal Resistance Lifetime
Test Conditions -10 Volts, 1 MHz -10 Volts, 1 GHz 50 mA, 100 MHz 50 mA, 1 GHz 100 mA 10 A -70 V
2, 3 1 1, 3 2, 3
Min.
V V
A
-70
-100 10 < 860 100
C/W 10 mA / 6 mA ns
Total capacitance is equivalent to the sum of junction capacitance C j and parasitic capacitance. Series resistance RS is equivalent to the total diode series resistance including the junction resistance Rj. RS and CP measures on an HP4291A with die mounted in an ODS-186 package with conductive silver epoxy. Steady-state R JL measured with die mounted in an ODS-186 package with conductive silver epoxy.
V 2.0
Specifications subject to change without notice. n North America: Tel. (800) 366-2266, Fax (800) 618-8883 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 Visit www.macom.com for additional data sheets and product information.
1
Silicon Flip Chip PIN Diode Handling Procedures
The following precautions should be observed to avoid damaging these devices.
MA4FCP200 Mounting Techniques
These devices were designed for insertion onto hard or soft substrates with the junction side down. They can be mounted with conductive epoxy or with a low temperature solder preform. The die can also be assembled with the junction side up, and wire or ribbon bonds made to the pads.
Cleanliness
These devices should be handled in a clean environment. Do not attempt to clean die after installation.
ESD These devices very susceptible to ESD and are rated Class 0 (0-199V) per HBM MIL-STD-883, method 3015.7 [C = 100pF 10%, R = 1.5k 1%]. Even though tested die pass 100V ESD, they must be handled in a static-free environment. General Handling The protective polymer coating on the active areas of these devices provides scratch protection, particularly for the metal airbridge that contacts the anode. Die can be handled with tweezers or vacuum pickups and are suitable for use with automatic pick-and-place equipment.
Solder Die Attach Solder that does not scavenge gold, such as Indalloy #2, is recommended. Sn-Pb based solders are not recommended due to solder embrittlement. Do not expose die to a temperature greater than 235C, or greater than 200C for longer than 10 seconds. No more than three seconds of scrubbing should be required for attachment. Epoxy Die Attach Assembly can be preheated to 125 to 150C. Use a minimum amount of silver epoxy. Cure epoxy as per manufacturer's schedule. For extended cure times, temperatures should be kept below 200C.
Applications
These devices are well suited as series diodes in broadband multi-throw switches through 26 GHz. In addition, the exceptional RC product makes them useful as shunt switches at millimeter frequencies. The low parasitic values of L and C make additional circuit tuning unnecessary.
Absolute Maximum Ratings1
Parameter Forward Current2 Reverse Voltage Operating Temperature Storage Temperature Dissipated Power2 Mounting Temperature Absolute Maximum 125 mA -70 V -55C to +150C -55C to +150C 145 mW +235C for 10 seconds
1. Exceeding these limits may cause permanent damage. 2. Steady-state R JL measured with die mounted in an ODS-186 package with conductive silver epoxy..
Typical Performance Curves @ +25C1
Typical Total Resistance RS vs. Forward Current and Frequency
5 4
0.025 0V 0.020
Typical Total Capacitance CP vs. Reverse Voltage and Frequency
Rs (ohms)
2 100mA 1 0 0 200 400 600 800 1000
Ct (pF)
3
10mA
50mA
0.015 0.010 0.005 0.000 0 200 400 600 800 1000
-10V
FREQUENCY (MHz)
FREQUENCY (MHz)
1. RS and CP measures on an HP4291A with die mounted in an ODS-186 package with conductive silver epoxy.
Specifications subject to change without notice. n North America: Tel. (800) 366-2266, Fax (800) 618-8883 n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 Visit www.macom.com for additional data sheets and product information.
V 2.0
2

▲Up To Search▲

Price & Availability of MA4FCP200

	To Download MA4FCP200 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .