![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
175 Watts LPS170 Series Total Power: 110-175 Watts Input Voltage: 85-264 VAC 120-300 VDC # of Outputs: Single Electrical Specs Input Input range Frequency Inrush current Efficiency EMI filter 85-264 VAC, 120-300 VDC 47-63 Hz 38 A max, cold start @ 25C 75% typical at full load Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted 0.99 typical 1.0 mA @ 50/60 Hz, 264 VAC input Power factor Safety ground leakage current Special Features * Active power factor correction * IEC EN61000-3-2 compliance * Wide Range Adjustable output Remote sense on main output * Single wire current sharing * Power fail and remote inhibit * Built-in EMI filter * Low output ripple * Overvoltage protection * Overload protection * Thermal overload protection * DC power good * 5 V standby output * 12 V Aux output * Optional cover (-C suffix) Output Maximum power 110 W convection (75 W with cover) 175 W with 30 CFM forced air (130 W with cover) 2:1 wide ratio minimum 20 ms @175 W load at nominal line Short circuit protection on all outputs. Case overload protected @ 110-145% above peak rating 10% to 40% above nominal output 5 V @ 2A regulated 5% 12 V @ 1 A -5 %, +10% Adjustment range Hold-up time Overload protection Overvoltage protection Standby output Aux output Logic Control Power failure TTL logic signal goes high 100 - 500 msec after V1 output; It goes low at least 4 msec before loss of regulation Requires contact closure to inhibit outputs Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation Environmental Operating temperature: 0 to 50C ambientderate each output at 2.5% per degree from 50 to 70C Electromagnetic susceptibility: designed to meet IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Humidity: Operating; non-condensing 5% to 95% Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75 G peak 5 Hz to 500 Hz, operational Storage temperature: -40 to 85C Temperature coefficient: .04% per C MTBF demonstrated: >550,000 hours at full load and 25C ambient conditions Remote inhibit Remote sense DC-OK Safety VDE UL CB CSA CE NEMKO 0805/EN60950 (IEC950) UL1950 Certificate and report CSA 22.2-234 Level 3 Mark (LVD) EN 60950/EMKO-TUE rev 08.09.03 118 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 AMERICAS 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 EUROPE Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 ASIA Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 LPS170 Series Ordering Information Model Number LPS172 LPS173 LPS174 LPS175 Output Voltage 5 V (2.5-6V) 12 V (6-12 V) 15 V (12-24 V) 24 V (24-54 V) Minimum Load 0A 0A 0A 0A Maximum Load with Convection Cooling 22 A 9.1 A 7.3 A 4.5 A Maximum Load with 30 CFM Forced Air 35 A 15 A 12 A 7.5 A Peak Load 38 A 16.5 A 13.2 A 8.2 A Regulation2 Ripple P/P(PARD)3 50 mV 120 mV <1% <1% 2% 2% 2% 2% 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4. Remote inhibit resets OVP latch Note: -C suffix added to the model number indicates cover option. Ordering Information Connector SK1 LPS17x PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN 9 PIN 10 TB-1 TB-2 PIN 1 PIN 3 PIN 5 +12V 5V Standby Common V1 SWP Common +V1 sense Sense common Remote inhibit DC power good POK COMMON Main output GROUND LINE NEUTRAL Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) PINS: 08-58-0111 Molex 19141-0058 1 6 5 10 SK1 + - SK3 1.50 (38.1) Voltage Adj POT 0.75 (19.0) 0.95 (24.0) 0.55 (14.0) SK3 SK4 6.61 (168.0) 7.4 (188.0) 8.5 (216.0) Mating Connectors (SK4) AC Input: (SK3) DC Output: 531 (SK1) Control Signals: Molex 90142-0010 (USA) PINS: 90119-2110 or Amp: 87977-3 PINS: 87309-8 Astec connector kit #70-841-016 Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is 0.02". 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Mounting screw maximum insertion depth is 0.12". 5. Warranty: 1 year 6. Weight: 1.8 lb / 0.85 kg SK4 M3 #6-32 0.88 (22.2) 1.07 (27.2) 2.11 (53.5) 4.25 (108.0) M3(8 PLACES) 2.50 (63.5) #6-32(8 PLACES) www.astecpower.com 119 |
Price & Availability of LPS175
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |