View LC503TPG1-30P-A1_1263514.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Cree(R) 5-mm Round LED
Model # LC503TPG-30P-A Data Sheet
30-degree, 5-mm LED lamp in green color with water-transparent lens and stopper
Applications
* * * * Advertising Signs Indicators LCD Back Light Moving-Message Signs
Absolute Maximum Ratings (TA = 25C)
Items Forward Current Peak Forward Current Reverse Voltage Power Dissipation Operation Temperature Storage Temperature Lead Soldering Temperature
Note
Symbol IF IFP VR PD Topr Tstg Tsol
Absolute Maximum Rating 25 100 5 100 -40 ~ +95 -40 ~ +100
Unit mA mA V mW C C
Max. 260C for 3 sec. max. (3 mm from the base of the epoxy bulb)
Note: Pulse width msec, duty 1/10.
Typical Electrical & Optical Characteristics (TA = 25C)
Characteristics Forward Voltage Forward Voltage Reverse Current Dominant Wavelength Luminous Intensity 50% Power Angle 2 Symbol VF VF IR
D
Condition IF = 20 mA IF = 1.0 A VR = 5 V IF = 20 mA IF = 20 mA IF = 20 mA
Unit V V A nm mcd deg
Minimum
Typical 3.4
Maximum 4.0 2.5 100
1.7
520 4180
527 7500 30
535
IV 1/2H-H
D-CT066.000 Data Sheet: CL
Subject to change without notice. www.cree.com/ledlamps
Standard Bins for LC503TPG-30P-A (IF = 20 mA)
Lamps are sorted to luminous intensity (IV) and dominant wavelength (
D
) bins shown.
Orders for LC503TPG1-30P-A1 may be filled with any or all bins contained as below. All luminous intensity (IV) and dominant wavelength ( X7
D
) values shown and specified are at IF = 20 mA. X9 Z1 or above Z
X8
Luminous Intensity (IV)
12000 mcd
8200 mcd Y 5860 mcd X 4180 mcd 520 nm 525 nm 530 nm
D
535 nm
Dominant Wavelength (
)
Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. Pb content <1000 ppm. 3. Tolerance of measurement of luminous intensity is 15%. 4. Tolerance of measurement of dominant wavelength is 1 nm. 5. Tolerance of measurement of VF is 0.05 V. 6. Packaging methods are available for selection; please refer to the "Cree LED Lamp Packaging Standard" document. 7. Please refer to the "Cree LED Lamp Reliability Test Standards" document for reliability test conditions. 8. Please refer to the "Cree LED Lamp Soldering & Handling" document for information about how to use this LED product safely.
Copyright (c) 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
2
CLD-CT066.000
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps
Document No. SPE/LC503TPG1-30P-A1 Rev. No. 02
Graphs
Graphs
If (mA)
-50 Vr(V) -40 -30 -20 -10 0 0.0 -10.0 -20.0 -30.0 -40.0 Ir(uA) FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. -50.0
100.0 80.0 60.0 40.0 20.0
0.0 3.0 3.4 3.8 4.2 4.6 5.0 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE.
Vf(V)
Half Power WL=38nm Domi WL= 525nm
5.0 4.0 3.0 2.0 1.0 0.0 0.0 If(mA) 20.0 40.0 60.0 80.0 100.0
I (RELATIVE LUMINOUS INTENSITY) 100% 75% 50% 25% 0% 300 400 500 600 700 WL(nm) 800
FIG.3 RELATIVE LUMINOUS INTENSITY VS. FORWARD CURRENT.
FIG.4 RELATIVE LUMINOUS INTENSITY VS. WAVELENGTH.
50 40 30 20 10 0
IF(mA)
50% Power Angle : 30
0
Ie(%)
100%
80%
60%
40%
Ta( C) 0.0 20.0 40.0 60.0 80.0 100.0
-90 -60 -30 0 30 60 90
20% 0%
FIG.5 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE (Tjmax=105 C)
FIG.6 FAR FIELD PATTERN
ems red by ved by3
Signatures
LiuZM
Date
2006-03-31 Rev. No 02 Date
Revision History
Change Description 2006-03-31 Cancel VF bin.
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps
are registered 2006-03-31 ked byCree logo Aldosin trademarks of Cree, Inc.
Copyright (c) 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the
CLD-CT066.000 David 2006-03-31
Mechanical Dimensions
All dimensions are in mm. Tolerance is 0.25 mm unless otherwise noted. An epoxy meniscus may Dimension Draw ingthe leads. extend about 1.5 mm down Burr around bottom of epoxy may be 0.5 mm max.
Document No. SPE/LC503TPG1-30P-A1 Rev. No. 02
maximum ting 5 0
Unit mA mA V
0 +95 +100
mW C C
C for 3 sec Max.
base of the epoxy bulb) Notes
RoHS Compliance The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or = 25Crestricted materials such product are below the in an exempted application, in (also referred to as Direc) Taotherwise limits) permitted for in thissubstances, or are usedmaximum concentration values accordance with EU the threshold tive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006.
s(
Vision ondition Advisory Claim Min.
Typ. 3.4 ---
Max. 4.0 2.5
Unit V V
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps
Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye.
F
= 20mA
Cree logo = 1.0 A
--1.7
F
Copyright (c) 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the are registered trademarks of Cree, Inc.
CLD-CT066.000
Kit Number System
Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the "Cree LED Lamp Packaging Standard" document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner:
Standard/Custom
0: Standard C: Custom
VF
0: Full forward voltage distribution 1~9, A~Z . . . : special request *
Wd/Color aaaaaaaaa-aaa-aa- x x x x x IV
1: Full-color distribution 2~9, A~Z . . . : special request * 0: Full luminous intensity distribution 1~9, A~Z . . . :special request *
Packing type Product P/N
0: Standard = Bulk pack 1~9, A~Z . . . : special request *
* Contact your Cree sales representative for ordering information.
Standard Available Kits*
Kit Number LC503TPG1-30P-A1-00001 LC503TPG1-30P-A1-00002 Description 5 mm Round 30 Pure-Green 527 nm, FULL RANK, Bulk Pack 5 mm Round 30 Pure-Green 527 nm, X8, X9, Bulk Pack
* Please contact your Cree representative about the availability of non-standard kits.
Copyright (c) 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc.
5
CLD-CT066.000
Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps

▲Up To Search▲

Price & Availability of LC503TPG1-30P-A1

	To Download LC503TPG1-30P-A1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .