View DCR604SE21_1231845.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DCR604SE
DCR604SE
Phase Control Thyristor Advance Information
Supersedes January 2000 version, DS4450-4.0 DS4450-5.0 July 2001
FEATURES
s Double Side Cooling s High Surge Capability s High Mean Current s Fatigue Free
KEY PARAMETERS VDRM IT(AV) ITSM dI/dt 2100V 706A 8100A 700A/s
dVdt* 1000V/s
APPLICATIONS
s High Power Drives s High Voltage Power Supplies s DC Motor Control
*Higher dV/dt selections available
VOLTAGE RATINGS
Type Number Repetitive Peak Voltages VDRM VRRM V 2100 2000 1900 1800 1700 Conditions
DCR604SE21 DCR604SE20 DCR604SE19 DCR604SE18 DCR604SE17
Tvj = 0 to 125C, IDRM = IRRM = 30mA, VDRM, VRRM tp = 10ms, VDSM & VRSM = VDRM & VRRM + 100V respectively
Outline type code: E See Package Details for further information. Fig. 1 Package outline
Lower voltage grades available.
ORDERING INFORMATION
When ordering, select the required part number shown in the Voltage Ratings selection table. For example: DCR604SE20 Note: Please use the complete part number when ordering and quote this number in any future correspondance relating to your order.
1/8
www.dynexsemi.com
DCR604SE
CURRENT RATINGS
Tcase = 60C unless stated otherwise. Symbol Double Side Cooled IT(AV) IT(RMS) IT Mean on-state current RMS value Continuous (direct) on-state current Half wave resistive load 706 1109 995 A A A Parameter Conditions Max. Units
Single Side Cooled (Anode side) IT(AV) IT(RMS) IT Mean on-state current RMS value Continuous (direct) on-state current Half wave resistive load 487 766 646 A A A
CURRENT RATINGS
Tcase = 80C unless stated otherwise. Symbol Double Side Cooled IT(AV) IT(RMS) IT Mean on-state current RMS value Continuous (direct) on-state current Half wave resistive load 562 882 770 A A A Parameter Conditions Max. Units
Single Side Cooled (Anode side) IT(AV) IT(RMS) IT Mean on-state current RMS value Continuous (direct) on-state current Half wave resistive load 380 595 480 A A A
2/8
www.dynexsemi.com
DCR604SE
SURGE RATINGS
Symbol ITSM I2t ITSM I2t Parameter Surge (non-repetitive) on-state current I2t for fusing Surge (non-repetitive) on-state current I2t for fusing Conditions 10ms half sine; Tcase = 125oC VR = 50% VRRM - 1/4 sine 10ms half sine; Tcase = 125oC VR = 0 Max. 6.5 0.21 x 106 8.1 0.33 x 106 Units kA A2s kA A2s
THERMAL AND MECHANICAL DATA
Symbol Parameter Conditions Double side cooled Rth(j-c) Thermal resistance - junction to case Single side cooled Cathode dc Clamping force 8.0kN with mounting compound On-state (conducting) Tvj Virtual junction temperature Reverse (blocking) Tstg Storage temperature range Clamping force -55 7.2 125 125 8.8
o
Min. dc Anode dc -
Max. 0.041 0.074 0.092 0.018 0.036 135
Units
o
C/W
o
C/W C/W C/W C/W
o
o
Double side Single side
o
Rth(c-h)
Thermal resistance - case to heatsink
o
C
C C
o
kN
3/8
www.dynexsemi.com
DCR604SE
DYNAMIC CHARACTERISTICS
Symbol IRRM/IDRM dV/dt Parameter Peak reverse and off-state current Maximum linear rate of rise of off-state voltage Conditions At VRRM/VDRM, Tcase = 125oC To 67% VDRM Tj = 125oC. Gate open circuit. From 67% VDRM to 1100A Gate source 20V, 20 tr 0.5s, Tj = 125oC At Tvj = 125oC At Tvj = 125oC VD = 67% VDRM, Gate source 10V, 5 tr = 0.5s, Tj = 25oC Tj = 25oC, VD = 5V Tj = 25oC, VD = 5V Repetitive 50Hz Non-repetitive Typ. Max. 30 1000 350 700 0.93 0.667 1.5 500 70 Units mA V/s A/s A/s V m s mA mA s
dI/dt
Rate of rise of on-state current
VT(TO) rT tgd IL IH tq
Threshold voltage On-state slope resistance Delay time Latching current Holding current
Turn-off time
IT = 500A, tp = 1ms, Tj = 125C, VR = 50V, dIRR/dt = 20A/s, VDR = 67% VDRM, dVDR/dt = 20V/s linear
300
400
GATE TRIGGER CHARACTERISTICS AND RATINGS
Symbol VGT IGT VGD VFGM VFGN VRGM IFGM PGM PG(AV) Parameter Gate trigger voltage Gate trigger current Gate non-trigger voltage Peak forward gate voltage Peak forward gate voltage Peak reverse gate voltage Peak forward gate current Peak gate power Mean gate power Anode positive with respect to cathode See table, gate characteristics curve Conditions VDRM = 5V, Tcase = 25oC VDRM = 5V, Tcase = 25oC At 67% VDRM Tcase = 125oC Anode positive with respect to cathode Anode negative with respect to cathode Max. 3.0 150 0.25 30 0.25 5 10 100 5 Units V mA V V V V A W W
4/8
www.dynexsemi.com
DCR604SE
CURVES
1600 Measured under pulse conditions Tj = 125C 1400
1000 Instantaneous on-state current, IT - (A) 6 phase 1200 Half wave 3 phase d.c.
1200
Mean power dissipation - (W)
1.0 1.5 Instantaneous on-state voltage, VT - (V) 2.0
800
1000
800
600
600
400
400
200
200
0 0.5
00
200 400 600 Mean on-state current, IT(AV) - (A)
800
Fig.2 Maximum (limit) on-state characteristics
Fig.3 Dissipation curves
VTM Equation:VTM = A + Bln (IT) + C.IT+D.IT Where A = 1.086551 B = -0.173031 C = -3.307461 x 10-5 D = 0.056345 these values are valid for Tj = 125C for IT 500A to 1600A
5/8
www.dynexsemi.com
DCR604SE
10000 Conditions: Tj = 125C VR = 50V tp = 1ms
100
Table gives pulse power PGM in Watts
Pulse width s 20 25 100 500 1ms 10ms Frequency Hz 400 50 100 100 100 100 100 100 100 100 100 100 25 100 100 12.5 100 50 10 -
0W 10 W 50
W 20 W 10 5W
Gate trigger voltage, VGT - (V)
Recovered charge, QR - (C)
IT = 1500A IT = 500A
10
1000
Up
lim per
it 9
5%
1 Region of certain triggering
QR tp dIT/dt IRM 0.25xIRM
VGD
e L ow
r lim
it 5%
100 0.1
1.0 10 Rate of decay of on-state current, dIT/dt - (A/s)
100
0.1 0.001
0.01
Tj = 125C
0.1
Tj = 25C Tj = -40C
IT
1
Gate trigger current, IGT - (A)
10 IFGM
Fig.4 Recovered charge
0.1
Fig.5 Gate characteristics
20 I2t = I2 x t 2
Anode side cooled
Thermal Impedance - junction to case - (C/W)
Peak half sine wave on-state current - (kA)
Double side cooled
15
225
I2t value - (A2s x 103)
0.01
10
200
I2t 5 175
Conduction
Effective thermal resistance Junction to case C/W Double side 0.041 0.044 0.051 0.061 Anode side 0.074 0.077 0.084 0.093
d.c. Halfwave 3 phase 120 6 phase 60
0.001 0.001
0.01
0.1 Time - (s)
1.0
10
0 1 ms
10
1
2 3 45
10
150 20 30 50
Cycles at 50Hz Duration
Fig.6 Maximum (limit) transient thermal impedance junction to case 6/8
Fig.7 Surge (non-repetitive) on-state current vs time (with 50% VRRM at Tcase 125C)
www.dynexsemi.com
DCR604SE
PACKAGE DETAILS
For further package information, please contact your local Customer Service Centre. All dimensions in mm, unless stated otherwise. DO NOT SCALE. 2 holes O3.6 0.1 x 2.0 0.1 deep (One in each electrode)
Cathode tab Cathode O42max O25nom. Gate
O1.5
30 15
15 14
O25nom.
Anode
Nominal weight: 82g Clamping force: 8kN 10% Lead length: 420mm Lead terminal connector: M4 ring Package outine type code: E
7/8
www.dynexsemi.com
DCR604SE
POWER ASSEMBLY CAPABILITY
The Power Assembly group was set up to provide a support service for those customers requiring more than the basic semiconductor, and has developed a flexible range of heatsink / clamping systems in line with advances in device types and the voltage and current capability of our semiconductors. We offer an extensive range of air and liquid cooled assemblies covering the full range of circuit designs in general use today. The Assembly group continues to offer high quality engineering support dedicated to designing new units to satisfy the growing needs of our customers. Using the up to date CAD methods our team of design and applications engineers aim to provide the Power Assembly Complete solution (PACs).
DEVICE CLAMPS
Disc devices require the correct clamping force to ensure their safe operation. The PACs range offers a varied selection of pre-loaded clamps to suit all of our manufactured devices. This include cube clamps for single side cooling of `T' 22mm Clamps are available for single or double side cooling, with high insulation versions for high voltage assemblies. Please refer to our application note on device clamping, AN4839
HEATSINKS
Power Assembly has its own proprietary range of extruded aluminium heatsinks. They have been designed to optimise the performance or our semiconductors. Data with respect to air natural, forced air and liquid cooling (with flow rates) is available on request. For further information on device clamps, heatsinks and assemblies, please contact your nearest Sales Representative or Customer Services.
http://www.dynexsemi.com e-mail: power_solutions@dynexsemi.com
HEADQUARTERS OPERATIONS DYNEX SEMICONDUCTOR LTD Doddington Road, Lincoln. Lincolnshire. LN6 3LF. United Kingdom. Tel: 00-44-(0)1522-500500 Fax: 00-44-(0)1522-500550 DYNEX POWER INC. 99 Bank Street, Suite 410, Ottawa, Ontario, Canada, K1P 6B9 Tel: 613.723.7035 Fax: 613.723.1518 Toll Free: 1.888.33.DYNEX (39639) CUSTOMER SERVICE CENTRES Mainland Europe Tel: +33 (0)1 58 04 91 00. Fax: +33 (0)1 46 38 51 33 North America Tel: (613) 723-7035. Fax: (613) 723-1518. UK, Scandinavia & Rest Of World Tel: +44 (0)1522 500500. Fax: +44 (0)1522 500020 SALES OFFICES Mainland Europe Tel: +33 (0)1 58 04 91 00. Fax: +33 (0)1 46 38 51 33 North America Tel: (613) 723-7035. Fax: (613) 723-1518. Toll Free: 1.888.33.DYNEX (39639) / Tel: (949) 733-3005. Fax: (949) 733-2986. UK, Scandinavia & Rest Of World Tel: +44 (0)1522 500500. Fax: +44 (0)1522 500020 These offices are supported by Representatives and Distributors in many countries world-wide. (c) Dynex Semiconductor 2001 Publication No. DS4450-5 Issue No. 5.0 July 2001 TECHNICAL DOCUMENTATION - NOT FOR RESALE. PRINTED IN UNITED KINGDOM
Datasheet Annotations: Dynex Semiconductor annotate datasheets in the top right hard corner of the front page, to indicate product status. The annotations are as follows:Target Information: This is the most tentative form of information and represents a very preliminary specification. No actual design work on the product has been started. Preliminary Information: The product is in design and development. The datasheet represents the product as it is understood but details may change. Advance Information: The product design is complete and final characterisation for volume production is well in hand. No Annotation: The product parameters are fixed and the product is available to datasheet specification.
This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior notice the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request. All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners.
8/8
www.dynexsemi.com

▲Up To Search▲

Price & Availability of DCR604SE21

	To Download DCR604SE21 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .