View AZ10E131FN_1215018.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ARIZONA MICROTEK, INC.
AZ10E131 AZ100E131
ECL/PECL 4-bit D Flip-Flop FEATURES
* * * * * * * * PACKAGE AVAILABILITY 1100 MHz Min. Toggle Frequency PACKAGE PART NUMBER MARKING NOTES Differential Outputs AZM10E131 Individual and Common Clocks PLCC 28 AZ10E131FN 1,2 Individual Resets (asynchronous) AZM100E131 PLCC 28 AZ100E131FN 1,2 Paired Sets (asynchronous) Operating Range of 4.2V to 5.46V 1 Add R2 at end of part number for 13 inch (2.5K parts) Tape & Reel. 75k Internal Input Pulldown Resistors 2 Date code format: "YY" for year followed by "WW" for week. Direct Replacement for On Semiconductor MC10E131 & MC100E131
DESCRIPTION
The AZ10/100E131 is a quad master-slave D-type flip-flop with differential outputs. Each flip-flop may be clocked separately by holding Common Clock (CC) LOW and using the Clock Enable (CEn) inputs for clocking. Common clocking is achieved by holding the CEn inputs LOW and using CC to clock all four flip-flops. In this case, the CEn inputs perform the function of controlling the common clock to each flip-flop. Individual asynchronous resets are provided (Rn). Asynchronous set controls (Sn) are ganged together in pairs, with the pairing chosen to reflect physical chip symmetry. Data enters the master when both CC and CEn are LOW, and transfers to the slave when either CC or CEn (or both) go HIGH. NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established.
R3 D2 CE2 R2 VCCO 21 Q3 Q3
CE3
25 26
24
23
22
20
19
18
Q2
D3
27
17
Q2
S12
28
16
VCC Q1
V EE
1
Pinout: 28-Lead PLCC (top view)
15
CC
2
14
Q1
S03
3
13
Q0
D0
4
12
Q0
5
6
7
8
9
10
11
CE0
R0
D1
CE1
R1
NC
V CCO
* All VCC and VCCO pins are tied together on the die.
1630 S. STAPLEY DR., SUITE 127 * MESA, ARIZONA 85204 * USA * (480) 962-5881 * FAX (480) 890-2541 www.azmicrotek.com
AZ10E131 AZ100E131
LOGIC SYMBOL
S D3 CE3 R R3 D Q3 Q3
PIN DESCRIPTION
D2 D
S Q2 Q2 R R2 S03 S12 CC R1 R CE1 D1 D Q1 Q1 S
PIN D0 - D3 CE0 - CE3 R0 - R3 CC S03,S12 Q0 - Q3 Q0 - Q3 VCC , VCCO VEE NC
FUNCTION Data inputs Clock Enables (Individual) Resets Common Clock Sets (paired) True Outputs Inverting Outputs Positive Supply Negative Supply No connect
CE2
R0 R CE0 D0 D Q0 Q0 S
Absolute Maximum Ratings are those values beyond which device life may be impaired.
Symbol VCC VI VEE VI IOUT TA TSTG Characteristic PECL Power Supply (VEE = 0V) PECL Input Voltage (VEE = 0V) ECL Power Supply (VCC = 0V) ECL Input Voltage (VCC = 0V) Output Current --- Continuous --- Surge Operating Temperature Range Storage Temperature Range Rating 0 to +8.0 0 to +6.0 -8.0 to 0 -6.0 to 0 50 100 -40 to +85 -65 to +150 Unit Vdc Vdc Vdc Vdc mA C C
10K ECL DC Characteristics (VEE = -4.94V to -5.46V, VCC = VCCO = GND)
Symbol VOH VOL VIH VIL Characteristic
1
IIH
IIL IEE 1.
Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage Input LOW Voltage Input HIGH Current CC 350 S 450 R, CE 300 D 150 Input LOW Current 0.5 Power Supply Current 58 70 Each output is terminated through a 50 resistor to VCC - 2V.
Min -1080 -1950 -1230 -1950
-40C Typ
Max -890 -1650 -890 -1500
Min -1020 -1950 -1170 -1950
0C Typ
Max -840 -1630 -840 -1480 350 450 300 150
Min -980 -1950 -1130 -1950
25C Typ
Max -810 -1630 -810 -1480 350 450 300 150
Min -910 -1950 -1060 -1950
85C Typ
Max -720 -1595 -720 -1445 350 450 300 150
Unit mV mV mV mV A A mA
0.5 58 70
0.5 58 70
0.5 58 70
November 2006 * REV - 3
www.azmicrotek.com 2
AZ10E131 AZ100E131
10K PECL DC Characteristics (VEE = GND, VCC = VCCO = +5.0V)
Symbol VOH VOL VIH VIL Characteristic
1,2
IIH
IIL IEE 1. 2.
Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage1 Input LOW Voltage1 Input HIGH Current CC 350 350 S 450 450 R, CE 300 300 D 150 150 Input LOW Current 0.5 0.5 0.5 Power Supply Current 58 70 58 70 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50 resistor to VCC - 2V.
Min 3920 3050 3770 3050
-40C Typ
Max 4110 3350 4110 3500
Min 3980 3050 3830 3050
0C Typ
Max 4160 3370 4160 3520
Min 4020 3050 3870 3050
25C Typ
Max 4190 3370 4190 3520 350 450 300 150
Min 4090 3050 3940 3050
85C Typ
Max 4280 3405 4280 3555 350 450 300 150
Unit mV mV mV mV A A mA
0.5 58 70 58 70
100K ECL DC Characteristics (VEE = -4.2V to -5.46V, VCC = VCCO = GND)
Symbol VOH VOL VIH VIL Characteristic
1
IIH
IIL IEE 1.
Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage Input LOW Voltage Input HIGH Current CC 350 S 450 R, CE 300 D 150 Input LOW Current 0.5 Power Supply Current 58 70 Each output is terminated through a 50 resistor to VCC - 2V.
Min -1085 -1830 -1165 -1810
-40C Typ -1005 -1695
Max -880 -1555 -880 -1475
Min -1025 -1810 -1165 -1810
0C Typ -955 -1705
Max -880 -1620 -880 -1475 350 450 300 150
Min -1025 -1810 -1165 -1810
25C Typ -955 -1705
Max -880 -1620 -880 -1475 350 450 300 150
Min -1025 -1810 -1165 -1810
85C Typ -955 -1705
Max -880 -1620 -880 -1475 350 450 300 150
Unit mV mV mV mV A A mA
0.5 58 70
0.5 58 70
0.5 67 81
100K PECL DC Characteristics (VEE = GND, VCC = VCCO = +5.0V)
Symbol VOH VOL VIH VIL Characteristic
1,2
IIH
IIL IEE 1. 2.
Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage1 Input LOW Voltage1 Input HIGH Current 350 CC 350 S 450 450 R, CE 300 300 D 150 150 Input LOW Current 0.5 0.5 0.5 Power Supply Current 58 70 58 70 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50 resistor to VCC - 2V.
Min 3915 3170 3835 3190
-40C Typ 3995 3305
Max 4120 3445 4120 3525
Min 3975 3190 3835 3190
0C Typ 4045 3295
Max 4120 3380 4120 3525
Min 3975 3190 3835 3190
25C Typ 4045 3295
Max 4120 3380 4120 3525 350 450 300 150
Min 3975 3190 3835 3190
85C Typ 4045 3295
Max 4120 3380 4120 3525 350 450 300 150
Unit mV mV mV mV A A mA
0.5 58 70 67 81
November 2006 * REV - 3
www.azmicrotek.com 3
AZ10E131 AZ100E131
AC Characteristics (VEE = 10E(-4.94V to -5.46V), 100E(-4.2V to -5.46V); VCC = VCCO = GND or VEE = GND, VCC =VCCO = 10E(+4.94V to +5.46V), 100E(+4.2V to +5.46V))
Symbol Fmax Characteristic Max. Toggle Frequency Propagation Delay to Output CE 310 600 750 360 500 700 tPLH / tPHL CC 275 600 725 325 500 675 R 300 620 775 350 550 725 S 300 550 775 350 550 725 tS Setup Time2 D 200 20 150 20 tH Hold Time2 D 225 -20 175 -20 tRR Reset Recovery Time 450 150 400 150 Minimum Pulse Width tPW CLK, S, R 400 400 tSKEW Within-Device Skew1 60 60 Rise/Fall Times t r / tf 275 725 300 675 20% - 80% 1. Within-device skew is defined as identical transitions on similar paths through a device. 2. Setup/hold times guaranteed for both CC & CE. Min 1100 -40C Typ 1400 Max Min 1100 0C Typ 1400 Max Min 1100 25C Typ 1400 Max Min 1100 85C Typ 1400 Max Unit MHz
360 325 350 350 150 175 400 400
500 500 550 550 20 -20 150
700 675 725 725
360 325 350 350 150 175 400 400
500 500 550 550 20 -20 150
700 675 725 725
ps
ps ps ps ps
60 300 675 300
60 675
ps ps
November 2006 * REV - 3
www.azmicrotek.com 4
AZ10E131 AZ100E131
PACKAGE DIAGRAM PLCC 28
DIM A B C E F G H J K R U V W X T Z G1 K1
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 0.64 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 0.50 2O 10O 10.42 10.92 1.02
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 0.025 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 0.020 2O 10O 0.410 0.430 0.040
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALOWABLE MOLD FLASH IS 0.010mm (0.250in.) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKGE BOTTOM BY UP TO 0.012mm (0.300in.). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, THE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025mm (0.635in.).
November 2006 * REV - 3
www.azmicrotek.com 5
AZ10E131 AZ100E131
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.
November 2006 * REV - 3
www.azmicrotek.com 6

▲Up To Search▲

Price & Availability of AZ10E131FN

	To Download AZ10E131FN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .