 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| AD2C111 1 Form A Solid State Relay DESCRIPTION The AD2C111 is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. It is designed to replace electromechanical relays in general purpose switching applications. The relay consists of an integrated circuit that drives two rugged source-to-source enhancement type DMOS transistors - optically coupled to a light emitting diode. FEATURES APPLICATIONS * * * * * Low input control power consumption (2.5mA TYP) 130mA maximum continuous load current 30 ohms maximum on-resistance High input-to-output isolation Long life/high reliability * * * * * Reed relay replacement Meter reading systems Medical equipment Battery monitoring Multiplexers OPTIONS/SUFFIXES* ABSOLUTE MAXIMUM RATINGS* PARAMETER Storage Temperature Operating Temperature Continuous Forward Current Peak Forward Current Reverse Voltage Output Power Dissipation UNIT C C mA A V mW MIN -40 -40 TYP MAX 150 85 50 1 5 500 * * * -H -S -TR .04" (10.16mm) lead spacing (VDE0884) Surface Mount Option Tape and Reel Option NOTE: Suffixes listed above are not included in marking on device for part number identification. SCHEMATIC DIAGRAM + INPUT 1 4 LOAD *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. 2 - INPUT 3 LOAD APPROVALS * * UL FILE #E201932 C-UL FILE #E201932 (c) 2004 Solid State Optronics * San Jose, CA www.ssousa.com * +1.408.293.4600 Page 1 of 5 AD2C111 rev 1.40 (10/25/2004) AD2C111 1 Form A Solid State Relay ELECTRICAL CHARACTERISTICS - 25C PARAMETER INPUT SPECIFICATIONS LED Forward Voltage Turn-On Current Turn-Off Current V mA mA 0.2 1.8 2.5 2 5 If = 10mA Io = 100mA, Vo=20V T=10ms UNIT MIN TYP MAX TEST CONDITIONS OUTPUT SPECIFICATIONS Blocking Voltage Continuous Load Current On-Resistance Output Off-State Leakage Current I/O Capacitance V mA A pF 6 20 0.2 400 130 30 1 Io = 1uA If = 5mA Io = 130mA Vo = 400V If=0, f = 1.0MHz COUPLED SPECIFICATIONS Isolation Voltage Turn-On Time Turn-Off Time Isolation Resistance V ms ms G 100 3750 0.5 0.5 2 1 T=1 min If = 5mA, Io = 130mA If = 5mA, Io = 130mA (c) 2004 Solid State Optronics * San Jose, CA www.ssousa.com * +1.408.293.4600 Page 2 of 5 AD2C111 rev 1.40 (10/25/2004) AD2C111 1 Form A Solid State Relay PERFORMANCE DATA AD2C111 Typical Turn-On Time Distribution N = 100, Ambient Temperature = 25C AD2C111 Typical Turn-Off Time Distribution N = 100, Ambient Temperature = 25C 40 Device Count 30 20 10 0 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Turn-On Tim e (m s) 40 Device Count 30 20 10 0 0.25 0.3 0.35 0.4 0.45 0.5 0.55 Turn-Off Tim e (m s) AD2C111 Typical On-Resistance Distribution N = 100, Ambient Temperature = 25C AD2C111 Typical Leakage Current Distribution N = 100, Ambient Temperature = 25C 50 Device Count 40 30 20 10 0 17 18 19 20 21 22 23 24 On-Resistance (ohm s) Device Count 60 50 40 30 20 10 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 Leakage Current (uA) AD2C111 Typical Blocking Voltage Distribution N = 100, Ambient Temperature = 25C AD2C111 Maximum Load Current vs. Temperature 30 20 10 0 380 400 420 440 460 480 500 520 Blocking Voltage (V) Load Current (mA) 40 Device Count 150 100 50 0 20 40 60 -4 0 -2 0 80 0 Tem perature (C) (c) 2004 Solid State Optronics * San Jose, CA www.ssousa.com * +1.408.293.4600 Page 3 of 5 AD2C111 rev 1.40 (10/25/2004) AD2C111 1 Form A Solid State Relay MECHANICAL DIMENSIONS 4 PIN DUAL IN-LINE PACKAGE 4 PIN SURFACE MOUNT DEVICE END VIEW END VIEW TOP VIEW TOP VIEW BOTTOM VIEW BOTTOM VIEW (c) 2004 Solid State Optronics * San Jose, CA www.ssousa.com * +1.408.293.4600 Page 4 of 5 AD2C111 rev 1.40 (10/25/2004) AD2C111 1 Form A Solid State Relay DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. (c) 2004 Solid State Optronics * San Jose, CA www.ssousa.com * +1.408.293.4600 Page 5 of 5 AD2C111 rev 1.40 (10/25/2004) |
Price & Availability of AD2C111
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |