|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
74LVCV2G66 Overvoltage tolerant bilateral switch Rev. 01 -- 2 April 2004 Product data sheet 1. General description The 74LVCV2G66 is a high-performance, low-power, low-voltage, Si-gate CMOS device that provides superior performance to most advanced CMOS compatible TTL families. The 74LVCV2G66 provides two single pole, single throw analog or digital switches. Each switch includes an overvoltage tolerant input/output terminal (pin nZ), an output/input terminal (pin nY) and low-power active HIGH enable input (pin nE). The overvoltage tolerant switch terminals allow the switching of signals in excess of VCC. The low-power enable input eliminates the necessity of using current limiting resistors in portable applications when using control logic signals much lower than VCC. These inputs are also overvoltage tolerant. 2. Features s Wide supply voltage range from 2.3 V to 5.5 V s Ultra low-power operation s Very low ON-resistance: x 8.0 (typ) at VCC = 2.7 V x 7.5 (typ) at VCC = 3.3 V x 7.3 (typ) at VCC = 5.0 V. s 5 V tolerant input for interfacing with 5 V logic s High noise immunity s Switch handling capability of 32 mA s CMOS low-power consumption s Latch-up performance exceeds 250 mA s Incorporates overvoltage tolerant analog switch technology s Switch accepts voltages up to 5.5 V independent of VCC s SOT505-2 and SOT765-1 package s Specified from -40 C to +85 C and -40 C to +125 C. 3. Quick reference data Table 1: Quick reference data GND = 0 V; tr = tf 2.5 ns; min and max at Tamb = -40 C to +85 C; typical at Tamb = 25 C. Symbol tPZH, tPZL Parameter turn-on time E to Y or Z Conditions CL = 50 pF; RL = 500 VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V 1.0 1.0 3.8 2.7 7.5 5.0 ns ns Min Typ Max Unit Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch Table 1: Quick reference data ...continued GND = 0 V; tr = tf 2.5 ns; min and max at Tamb = -40 C to +85 C; typical at Tamb = 25 C. Symbol tPHZ, tPLZ Parameter turn-off time E to Y or Z Conditions CL = 50 pF; RL = 500 VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V CI CS CPD input capacitance switch capacitance power dissipation capacitance per switch OFF-state ON-state fi = 10 MHz; VCC = 3.3 V [1] [2] Min 1.0 1.0 - Typ 6.5 4.4 2.5 8.0 16 10.3 Max 13.5 9.0 - Unit ns ns pF pF pF pF [1] CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD x VCC2 x fi x N where: fi = input frequency in MHz; VCC = supply voltage in V; N = number of inputs. The condition is VI = GND to 5.5 V. [2] 4. Ordering information Table 2: Ordering information Package Temperature range Name 74LVCV2G66DP -40 C to +125 C 74LVCV2G66DC -40 C to +125 C TSSOP8 VSSOP8 Description plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm plastic very thin shrink small outline package; 8 leads; body width 2.3 mm Version SOT505-2 SOT765-1 Type number 5. Marking Table 3: Marking Marking code Y66 Y66 Type number 74LVCV2G66DP 74LVCV2G66DC 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 2 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 6. Functional diagram 1Y 1Z 1 7# 1 1 X1 2 1E 5 1 1 X1 001aaa531 2Z 2Y 6 3# 2E 001aaa530 Fig 1. Logic symbol. Fig 2. IEC logic symbol. Z Y E VCC 001aaa532 Fig 3. Logic diagram. 7. Pinning information 7.1 Pinning 1Z 1Y 2E GND 1 2 3 4 001aaa529 8 VCC 1E 2Y 2Z 66 7 6 5 Fig 4. Pin configuration. 7.2 Pin description Table 4: Pin 1 2 3 4 5 9397 750 13027 Pin description Symbol 1Z 1Y 2E GND 2Z Description independent input/output (overvoltage tolerance) independent input/output enable input (active HIGH) ground (0 V) independent input/output (overvoltage tolerance) (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 3 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch Pin description ...continued Symbol 2Y 1E VCC Description independent input/output enable input (active HIGH) supply voltage Table 4: Pin 6 7 8 8. Functional description 8.1 Function table Table 5: Input nE L H [1] H = HIGH voltage level; L = LOW voltage level. Function table [1] Switch OFF-state ON-state 9. Limiting values Table 6: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol VCC VI IIK ISK VS IS ICC, IGND Tstg Ptot [1] Parameter supply voltage input voltage input diode current switch diode current DC switch voltage range switch source or sink current VCC or GND current storage temperature power dissipation Conditions [1] Min -0.5 -0.5 -0.5 -65 Max +6.5 +6.5 -50 50 +6.5 50 100 +150 300 Unit V V mA mA V mA mA C mW VI < -0.5 V or VI > 6.5 V VI < -0.5 V or VI > 6.5 V enable and disable mode VS < -0.5 V or VS > 6.5 V Tamb = -40 C to +125 C - The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 4 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 10. Recommended operating conditions Table 7: Symbol VCC VI VS Tamb tr, tf Recommended operating conditions Parameter supply voltage input voltage DC switch voltage range operating ambient temperature input rise and fall times VCC = 2.3 V to 2.7 V VCC = 2.7 V to 5.5 V [1] Conditions Min 2.3 0 Typ - Max 5.5 5.5 5.5 +125 20 10 Unit V V V C ns/V ns/V enable and disable mode [1] 0 -40 0 0 To avoid drawing VCC current out of terminal nZ when switch current flows in terminal nY, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal nZ, no VCC current will flow out of terminal nY. In this case, there is no limit for the voltage drop across the switch. 11. Static characteristics Table 8: Static characteristics At recommended operating conditions; voltages are referenced to GND (ground 0 V). Symbol VIH Parameter HIGH-level input voltage Conditions VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V VIL LOW-level input voltage VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V ILI IS(OFF) input leakage current VI = 5.5 V or GND; VCC = 5.5 V [2] Min 0.6 x VCC 2.0 - Typ 0.1 0.1 Max 0.1 x VCC 0.5 5 10 Unit V V V V V A A Tamb = -40 C to +85 C [1] 0.55 x VCC - 0.15 x VCC V analog switch VS = 0 V or 5.5 V; OFF-state current per VCC = 2.3 V to 5.5 V; channel see Figure 5 analog switch ON-state current per channel quiescent supply current VS = 0 V or 5.5 V; VCC = 2.3 V to 5.5 V; see Figure 6 VI = VCC or GND; IO = 0 A; VCC = 5.5 V IS(ON) [2] - 0.1 10 A ICC ICC CI CS - 0.1 0.1 2.5 8.0 16 10 5 - A A pF pF pF additional quiescent VI = VCC - 0.6 V; IO = 0 A; supply current per pin VCC = 3.0 V to 5.5 V input capacitance switch capacitance OFF-state ON-state - 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 5 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch Table 8: Static characteristics ...continued At recommended operating conditions; voltages are referenced to GND (ground 0 V). Symbol VIH Parameter HIGH-level input voltage Conditions VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V VIL LOW-level input voltage VCC = 2.3 V to 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V ILI IS(OFF) input leakage current VI = 5.5 V or GND; VCC = 5.5 V [2] Min 0.6 x VCC 2.0 - Typ - Max 0.1 x VCC 0.5 5 10 Unit V V V V V A A Tamb = -40 C to +125 C 0.55 x VCC - 0.15 x VCC V analog switch VS = 0 V or 5.5 V; OFF-state current per VCC = 2.3 V to 5.5 V; channel see Figure 5 analog switch ON-state current per channel quiescent supply current VS = 0 V or 5.5 V; VCC = 2.3 V to 5.5 V; see Figure 6 VI = VCC or GND; IO = 0 A; VCC = 5.5 V IS(ON) [2] - - 10 A ICC ICC - - 40 50 A A additional quiescent VI = VCC - 0.6 V; IO = 0 A; supply current per pin VCC = 3.0 V to 5.5 V [1] [2] All typical values are measured at Tamb = 25 C. For overvoltage signals (VS > VCC) the condition VY < VZ must be observed. VCC VIL IS E Y Z VIH IS VO GND 001aaa534 VCC E Z Y IS VI VI GND VO 001aaa535 VI = GND and VO = GND or 5.5 V. VI = 5.5 V or GND and VO = open circuit Fig 5. Test circuit for measuring switch OFF-state current. Fig 6. Test circuit for measuring switch ON-state current. 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 6 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch Table 9: Resistance RON At recommended operating conditions; voltages are referenced to GND (ground 0 V); see test circuit Figure 7. Symbol RON(peak) Parameter C [1] VS = GND to VCC; VI = VIH IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V RON(rail) switch ON-state resistance (rail) VS = GND; VI = VIH IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V VS = VCC; VI = VIH IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V RON(flatness) switch ON-resistance (flatness) VS = GND to VCC; VI = VIH; see Figure 9 IS = 8 mA; VCC = 2.5 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.3 V IS = 32 mA; VCC = 5.0 V Tamb = -40 C to +125 C RON(peak) switch ON-state resistance (peak) VS = GND to VCC; VI = VIH IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V RON(rail) switch ON-state resistance (rail) VS = GND; VI = VIH IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V VS = VCC; VI = VIH IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V [1] All typical values are measured at Tamb = 25 C. Conditions Min Typ Max Unit Tamb = -40 C to +85 switch ON-state resistance (peak) - 13 10 8.3 7.4 8.5 8.0 7.5 7.3 8.5 7.2 6.5 5.7 17 10 5 3 30 25 20 15 20 18 15 10 20 18 15 10 - - - 30 25 20 15 20 18 15 10 20 18 15 10 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 7 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 16 RON () 12 VCC VIH E 8 Z Y IS 001aaa536 VS VCC = 2.5 V 2.7 V 3.3 V 5.0 V VI GND 001aaa533 4 0 0 2 4 VI (V) 6 VI = GND to 5.5 V; RON = VS/IS. VI = GND to 5.5 V; Tamb = 25 C. Fig 7. Test circuit for measuring switch ON-resistance. Fig 8. Typical switch ON-resistance as a function of input voltage. 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 8 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 16 RON () 12 Tamb = +85 C +25 C -40 C +125 C 001aaa537 16 RON () 12 001aaa538 Tamb = +85 C +25 C -40 C +125 C 8 8 4 4 0 0 2 4 VI (V) 6 0 0 2 4 VI (V) 6 a. VCC = 2.5 V 16 RON () 12 Tamb = +85 C +25 C -40 C +125 C 001aaa539 b. VCC = 2.7 V 16 RON () 12 Tamb = +85 C +25 C -40 C +125 C 001aaa540 8 8 4 4 0 0 2 4 VI (V) 6 0 0 2 4 VI (V) 6 c. VCC = 3.3 V d. VCC = 5.0 V Fig 9. Switch ON-resistance at various supply voltages as a function of input voltage. 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 9 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 12. Dynamic characteristics Table 10: Dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); test circuit Figure 12. Symbol tPHL, tPLH Parameter C [1] [2] Conditions Min Typ Max Unit Tamb = -40 C to +85 propagation delay nY to nZ see Figure 10 or nZ to nY VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 [3] [4] 0.4 0.4 0.3 0.2 4.7 4.4 3.8 2.7 6.0 7.9 6.5 4.4 9.7 10.3 11.3 1.2 1.0 0.8 0.6 12 8.5 7.5 5.0 16 15 13.5 9.0 - ns ns ns ns ns ns ns ns ns ns ns ns pF pF pF tPZH, tPZL turn-on time E to Y or Z see Figure 11 VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V tPHZ, tPLZ turn-off time E to Y or Z see Figure 11 VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V CPD power dissipation capacitance per switch CL = 50 pF; fi = 10 MHz VCC = 2.5 V VCC = 3.3 V VCC = 5.0 V [2] Tamb = -40 C to +125 C tPHL, tPLH propagation delay nY to nZ see Figure 10 or nZ to nY VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V tPZH, tPZL turn-on time E to Y or Z see Figure 11 VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V tPHZ, tPLZ turn-off time E to Y or Z see Figure 11 VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V [1] All typical values are measured at Tamb = 25 C. 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 - 2.0 1.5 1.5 1.0 15 11 9.5 6.5 20 19 17 11.5 ns ns ns ns ns ns ns ns ns ns ns ns 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 10 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch [2] [3] tPHL and tPLH propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified capacitance when driven by an ideal voltage source (zero output impedance). CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD x VCC2 x fi x N where: fi = input frequency in MHz; VCC = supply voltage in V; N = number of inputs. The condition is VI = GND to 5.5 V. [4] 13. Waveforms VI nY or nZ input GND t PLH VOH nZ or nY output VOL 001aaa541 VM VM t PHL VM VM Measurement points are given in Table 11. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 10. Input (Y or Z) to output (Z or Y) propagation delays. Table 11: VCC 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V Measurement points Input VM 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC Output VM 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC Supply voltage 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 11 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch VI nE input GND t PLZ VCC nY or nZ output LOW-to-OFF OFF-to-LOW VOL t PHZ output HIGH-to-OFF OFF-to-HIGH VOH Vy VM GND switch enabled switch disabled switch enabled 001aaa542 VM t PZL VM VX t PZH nY or nZ Measurement points are given in Table 12. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 11. Turn-on and turn-off times. Table 12: VCC 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V Measurement points Input VM 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC Output VM 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC VX VOL + 0.1 x VCC VOL + 0.3 V VOL + 0.3 V VOL + 0.3 V VY VOH - 0.1 x VCC VOH - 0.3 V VOH - 0.3 V VOH - 0.3 V Supply voltage 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 12 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch VEXT VCC PULSE GENERATOR VI D.U.T. RT CL RL VO RL mna616 Test data is given in Table 13. Definitions test circuit: RT = Termination resistance should be equal to output impedance Zo of the pulse generator. CL = Load capacitance including jig and probe capacitance. RL = Load resistance. VEXT = Test voltage for switching times. Fig 12. Load circuitry for switching times. Table 13: VCC 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V Test data Input VI VCC 2.7 V 2.7 V VCC tr, tf Load CL RL 500 500 500 500 2.0 ns 30 pF 2.5 ns 50 pF 2.5 ns 50 pF 2.5 ns 50 pF VEXT tPLH, tPHL open open open open tPZH, tPHZ GND GND GND GND tPZL, tPLZ 2 x VCC 6.0 V 6.0 V 2 x VCC Supply voltage 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 13 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 14. Additional dynamic characteristics Table 14: Additional dynamic characteristics At recommended conditions; typical values measured at Tamb = 25 C. Symbol dsin Parameter sine-wave distortion Conditions fi = 1 kHz; RL = 10 k; CL = 50 pF; see Figure 13 VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V fi = 10 kHz; RL = 10 k; CL = 50 pF; see Figure 13 VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V fON-state(res) switch ON-state signal frequency response RL = 600 ; CL = 50 pF; fi = 1 MHz; see Figure 14 VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V RL = 50 ; CL = 5 pF; fi = 1 MHz; see Figure 14 VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V OFF(ft) switch OFF-state signal feed-through attenuation RL = 600 ; CL = 50 pF; fi = 1 MHz; see Figure 15 VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V RL = 50 ; CL = 5 pF; fi = 1 MHz; see Figure 15 VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V Vct(ctl-sw) crosstalk between control input to signal output RL = 600 ; CL = 50 pF; fi = 1 MHz; tr = tf = 2 ns; see Figure 16 VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V 91 119 205 mV mV mV [2] [2] [1] [1] Min Typ Max Unit - 0.42 0.36 0.47 - % % % - 0.11 0.07 0.01 - % % % - 160 200 210 - MHz MHz MHz - 180 180 180 - MHz MHz MHz - -65 -65 -62 - dB dB dB - -37 -36 -36 - dB dB dB 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 14 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch Table 14: Additional dynamic characteristics ...continued At recommended conditions; typical values measured at Tamb = 25 C. Symbol Vct(sw-sw) Parameter Conditions Min Typ Max Unit crosstalk between switches RL = 600 ; CL = 50 pF; fi = 1 MHz; see Figure 17 VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V RL = 50 ; CL = 5 pF; fi = 1 MHz; see Figure 17 VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V Q injection charge CL = 0.1 nF; Vgen = 0 V; Rgen = 0 ; f = 1 MHz; RL = 1 M; see Figure 18 VCC = 2.5 V VCC = 3.3 V VCC = 4.5 V VCC = 5.5 V [1] [2] [3] - -56 -55 -55 - dB dB dB - -29 -28 -28 - dB dB dB - <0.003 0.003 0.0035 0.0035 - pC pC pC pC Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads -3 dB. Adjust fi voltage to obtain 0 dBm level at input. Definition: Q = Vout x CL. Guaranteed by design. 0.5VCC VCC RL VIH E Z or Y 10 F Y or Z fi 600 CL D GND 001aaa544 Test conditions: VCC = 2.3 V: Vi = 2 V (p-p). VCC = 3 V: Vi = 2.5 V (p-p). VCC = 4.5 V: Vi = 4 V (p-p). Fig 13. Test circuit for measuring sine-wave distortion. 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 15 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 0.5VCC VCC RL VIH 0.1 F E Z or Y Y or Z fi 50 CL dB GND 001aaa543 Fig 14. Test circuit for measuring the frequency response when switch is in ON-state. 0.5VCC VCC RL 0.5VCC RL VIL 0.1 F E Z or Y Y or Z fi 50 CL dB GND 001aaa545 Fig 15. Test circuit for measuring feed-through attenuation when switch is in OFF-state. 0.5VCC Ri = 600 0.5VCC VCC E RL = 600 Y or Z Z or Y logic input 50 CL = 50 pF VO GND 001aaa546 Fig 16. Test circuit for measuring crosstalk between control input and output. 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 16 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 0.5VCC VIH 0.1 F 1E Ri 600 RL 1Y or 1Z 1Z or 1Y CL 50 pF fi 50 VO1 channel ON 0.5VCC VIL 2E 2Y or 2Z Ri 600 RL 2Z or 2Y CL 50 pF VO2 channel OFF 001aaa547 20 log10 (VO2/VO1) or 20 log10 (VO1/VO2). Fig 17. Test circuit for measuring crosstalk between switches. VCC E Y or Z Rgen logic input Vgen GND 001aaa548 RL = 1 M CL = 0.1 nF Z or Y VO logic (E) off input on off VO VOUT 001aaa549 Fig 18. Test circuit for measuring injection charge. 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 17 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 15. Application information Use the 74LVCV2G66 to reduce component count and footprint in low-power portable applications. Typical `66' devices do not have low-power enable inputs causing a high ICC. To reduce power consumption in portable (battery) applications, a current limiting resistor is used. (see Figure 19a). The low-power enable inputs of the 74 LVCV2G66 have much lower ICC, eliminating the necessity of the current limiting resistor (see Figure 19b). 5V 1 M VCC 3V E 3V Z E 5V VCC Y Y Z '66' device 74LVCV2G66 (a) (b) 001aaa550 Fig 19. Application example. 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 18 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 16. Package outline TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm SOT505-2 D E A X c y HE vMA Z 8 5 A pin 1 index A2 A1 (A3) Lp L 1 e bp 4 wM detail X 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.15 0.00 A2 0.95 0.75 A3 0.25 bp 0.38 0.22 c 0.18 0.08 D(1) 3.1 2.9 E(1) 3.1 2.9 e 0.65 HE 4.1 3.9 L 0.5 Lp 0.47 0.33 v 0.2 w 0.13 y 0.1 Z(1) 0.70 0.35 8 0 Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION SOT505-2 REFERENCES IEC JEDEC --JEITA EUROPEAN PROJECTION ISSUE DATE 02-01-16 Fig 20. Package outline TSSOP8. 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 19 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm SOT765-1 D E A X c y HE vMA Z 8 5 Q A pin 1 index A2 A1 (A3) Lp L 1 e bp 4 wM detail X 0 2.5 scale 5 mm DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1 A1 0.15 0.00 A2 0.85 0.60 A3 0.12 bp 0.27 0.17 c 0.23 0.08 D(1) 2.1 1.9 E(2) 2.4 2.2 e 0.5 HE 3.2 3.0 L 0.4 Lp 0.40 0.15 Q 0.21 0.19 v 0.2 w 0.13 y 0.1 Z(1) 0.4 0.1 8 0 Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT765-1 REFERENCES IEC JEDEC MO-187 JEITA EUROPEAN PROJECTION ISSUE DATE 02-06-07 Fig 21. Package outline VSSOP8. 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 20 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 17. Revision history Table 15: Revision history Release date 20040402 Data sheet status Product data sheet Change notice Order number 9397 750 13027 Supersedes Document ID 74LVCV2G66_1 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 21 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 18. Data sheet status Level I II Data sheet status [1] Objective data Preliminary data Product status [2] [3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). III Product data Production [1] [2] [3] Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 19. Definitions Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 20. Disclaimers Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 21. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com 9397 750 13027 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 2 April 2004 22 of 23 Philips Semiconductors 74LVCV2G66 Overvoltage tolerant bilateral switch 22. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 9 10 11 12 13 14 15 16 17 18 19 20 21 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 5 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . 10 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Additional dynamic characteristics . . . . . . . . 14 Application information. . . . . . . . . . . . . . . . . . 18 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 19 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 21 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 22 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Contact information . . . . . . . . . . . . . . . . . . . . 22 (c) Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 2 April 2004 Document order number: 9397 750 13027 Published in The Netherlands |
Price & Availability of 74LVCV2G66DP |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |