 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HA1631S01/02/03/04 Series Single CMOS Comparator (Push Pull/Open Drain Output) REJ03D0056-0100Z Rev.1.00 2003.08.08 Description The HA1631S01/02/03/04 are low power single CMOS Comparator featuring low voltage operation with typical current supply of 5 A/50 A. They are designed to operate from a single power supply. HA1631S01/02 have push-pull full swing outputs that allow direct connections to logic devices. The Open Drain version HA1631S03/04 enable Output Level shifting through external pull up resistors. Available in an ultra-small CMPAK-5 package, they occupy only 1/8 the area of the SOP-8 package. Features * Low supply current HA1631S01/03: IDDtyp = 5 A (VDD = 3.0 V) HA1631S02/04: IDDtyp = 50 A (VDD = 3.0 V) * Low voltage operation: VDD = 1.8 to 5.5 V * Low input offset voltage: VIOmax = 5 mV * Low input bias current: IIBtyp = 1 pA * Maximum output voltage: VOHmin = 2.9 V (at VDD = 3.0 V) * Input common voltage range includes ground * On-chip ESD protection * Available in CMPAK-5 and MPAK-5 package using Pb free lead frame Outline CMPAK-5V HA1631S01CM HA1631S02CM HA1631S03CM HA1631S04CM MPAK-5V HA1631S01LP HA1631S02LP HA1631S03LP HA1631S04LP Rev.1.00, 2003.08.08, page 1 of 22 HA1631S01/02/03/04 Series Pin Arrangement VDD 5 VOUT 4 +- 1 2 3 VIN(+) VSS VIN(-) Equivalent Circuit VDD * IN- IN+ OUTPUT VSS * Not available in Open Drain version (HA1631S03/04) Rev.1.00, 2003.08.08, page 2 of 22 HA1631S01/02/03/04 Series Absolute Maximum Ratings (Ta = 25C) Item Supply voltage Differential input voltage Input voltage Output current Power dissipation Operating temperature Storage temperature Symbol VDD VIN(diff) VIN IOUT PT Topr Tstg Ratings 7.0 -VDD to +VDD 0.1 to +VDD 28 80/120 -40 to +85 -55 to +125 Unit V V V mA mW C C Note 1 Note 2 CMPAK/MPAK Remarks Notes: 1. Do not apply input voltage exceeding VDD or 7 V. 2. The maximum output current is the maximum allowable value for continuous operation. Electrical Characteristics (Ta = 25C, VDD = 3.0 V, VSS = 0 V) Item Input offset voltage Input bias current Input offset current Common mode input voltage range Supply current Response time HA1631S01/03 HA1631S02/04 HA1631S01 HA1631S01/03 HA1631S01 HA1631S01/03 HA1631S02 HA1631S02/04 HA1631S02 HA1631S02/04 Output source current (HA1631S01/02) Output sink current Common mode rejection ratio HA1631S01/03 HA1631S02/04 Symbol VIO IIB IIO VCM IDD TPLH TPHL tr tf TPLH TPHL tr tf IOSOURCE IOSINK CMRR PSRR VOH VOL ILO Vopr Min -- -- -- -0.1 -- -- -- -- -- -- -- -- -- -- 6 7 60 50 60 VDD-0.1 -- -- 1.8 Typ -- (1) (1) -- 5 50 (1.20) (0.55) (24) (7) (0.33) (0.17) (12) (7) 13 14 80 70 80 -- -- (0.1) -- Max 5 100 100 2.1 10 100 -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0.1 -- 5.5 Unit mV pA pA V A A s s ns ns s s ns ns mA mA dB dB dB V V nA V Vout = 2.5V Vout = 0.5V VIN1 = 0V, VIN2 = 2V VDD1 = 1.8V, VDD2 = 5.5V RL = 10k to VSS RL = 10k to VDD VIN+ = 1V, VIN- = 0V, VO = 3V Test Conditions VIN = VDD/2, RL = 1M VIN = VDD/2 VIN = VDD/2 VDD = 3V, VIN+ = 1V, VIN- = 0V 1V DC bias, 100mV overdrive, CL = 15pF Power supply rejection ratio Output voltage high Output voltage low Output leakage current (Only for HA1631S03/04) Operating voltage range Note: ( ): Design specification Rev.1.00, 2003.08.08, page 3 of 22 HA1631S01/02/03/04 Series Table of Graphs Electrical Characteristics Supply current IDD vs. Supply voltage(Out H) vs. Supply voltage(Out L) HA1631S01 Figure 1-1 1-2 1-3 1-18 1-4 1-17 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-15 1-20 1-14 1-16 1-19 1-21 1-22 HA1631S02 Figure 2-1 2-2 2-3 2-18 2-4 2-17 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-15 2-20 2-14 2-16 2-19 2-21 2-22 HA1631S03 Figure 3-1 3-2 3-3 3-4 -- 3-14 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-15 -- -- -- -- 3-16, 3-17 HA1631S04 Figure 4-1 4-2 4-3 4-4 -- 4-14 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 4-12 4-13 4-15 -- -- -- -- 4-16, 4-17 Test Circuit No. 1 2 1 4 5 6 5 8 7 9 11 12 10 10 13 13 13 13 13 13 13 13 vs. Temperature(Out H) Output high voltage Output source current Output low voltage Output sink current Input offset voltage Common mode input voltage range Power supply rejection ratio Common mode rejection ratio Input bias current Falling time VOH IOSOURCE VOL IOSINK VIO VCM PSRR CMRR IIB tf vs. Rload vs. Output high voltage vs. Rload vs. Output low voltage vs. Supply voltage vs. Temperature vs. Temperature vs. Supply voltage vs. Input voltage vs. Temperature vs. Input voltage vs. Temperature vs. Cload Time waveform Rising time tr vs. Temperature vs. Cload Time waveform Propagation delay time TPLH TPHL Time waveform Time waveform Rev.1.00, 2003.08.08, page 4 of 22 HA1631S01/02/03/04 Series Test Circuits 1. Supply Current, IDD (Output High) A - + 1V VDD + - 1V 2. Supply Current, IDD (Output Low) A VDD 3. Output Source Current, IOSOURCE 4. Output High Voltage, VOH (Output High) - + 1V VOUT 3V - + 1V RLOAD 3V 5. Output Sink Current, IOSINK 6. Output Low Voltage, VOL (Output Low) + - 1V VOUT 3V + - 1V RLOAD 3V 7. Input Offset Voltage, VIO 1M 1k 1k 10k - + 1M 1.5V Note: VIO = VOUT - 1.5V 100F VOUT Only for Open Drain 3V 8. Input Offset Voltage vs. VDD 1M 1k 1k 1M - + -VDD 100F VDD VIN 9. Common Mode Input Voltage Range, VCM Only for Open Drain 1M 10k 1k - 3V + VIO 1k VIN 1M VIN = 0V 100F VCML 1.5V Note: VCML and VCMH are values of VIN when VIO changes more than 50dB taking VIN = 0V as reference. 10. Input Bias Current, IIB A VIN VCMH - + 3V VIN Rev.1.00, 2003.08.08, page 5 of 22 HA1631S01/02/03/04 Series 11. Power Supply Rejection Ratio, PSRR Only for Open Drain 1M 10k 1k - VDD/2 + VOUT 1k VDD 1M -1.8V -VDD/2 100F 5.5V 12. Common Mode Rejection Ratio, CMRR Only for Open Drain 1M 10k 1k - 1.5V + VOUT 1k VIN VIN 1M -1.5V 100F -1.5V 0.5V Measure Calculate VIO Point VOUT1 VOUT2 PSRR Calculation |(VIO2 - VIO1)| VIO1 = VOUT1/1000 PSRR = 20log10 5.5V - 1.8V VIO2 = VOUT2/1000 Measure Calculate VIO CMRR Calculation Point |(VIO2 - VIO1)| VOUT1 VIO1 = VOUT1/1000 CMRR = 20log10 0.5V - (-1.5V) VIO2 = VOUT2/1000 VOUT2 13. Falling Time, Rising Time, Propagation Delay Time TPLH, TPHL Only for Open Drain 10k - 2V 0.1V 1.0V + C LOAD Only for Open Drain 10k - + 50 CLOAD -1V 15pF 2V 50 -1V 15pF Overdrive = 0.1V Overdrive = 1.0V input 50% 50% input 90% 90% output TPLH 50% 50% output 10% 10% tf TPHL tr Only for Push Pull HA1631S01/02 input 50% 50% input 90% output TPLH 50% 50% output 10% TPHL Only for Open Drain HA1631S03/04 tf Rev.1.00, 2003.08.08, page 6 of 22 HA1631S01/02/03/04 Series Main Characteristics Figure 1-1 HA1631S01 Supply Current vs. Supply Voltage (Output High) Supply Current IDD (A) Ta = 25C VIN+ = 1.0V VIN- = 0.0V 7.0 Supply Current IDD (A) 7.0 Figure 1-2 HA1631S01 Supply Current vs. Supply Voltage (Output Low) Ta = 25C 6.0 5.0 4.0 3.0 2.0 1.0 0.0 0 6.0 VIN+ = 0.0V 5.0 4.0 3.0 2.0 1.0 0.0 0 1 2 3 4 5 6 VIN- = 1.0V 1 2 3 4 5 6 Supply Voltage VDD (V) Figure 1-3 HA1631S01 Supply Current vs. Ambient Temperature VDD = 5.0V VDD = 3.0V VDD = 1.8V Supply Voltage VDD (V) Figure 1-4 HA1631S01 Output High Voltage vs. Output Source Current 3.5 3.0 2.5 2.0 1.5 1.0 0.5 Ta = 25C VDD = 3.0V 7.5 5.0 2.5 0.0 -50 Output High Voltage VOH (V) 10.0 Supply Current IDD (A) -25 0 25 50 75 100 0.0 0 10 20 30 40 Ambient Temperature Ta (C) Figure 1-5 HA1631S01 Output Low Voltage vs. Output Sink Current Ta = 25C VDD = 3.0V Output Source Current IOSOURCE (mA) Figure 1-6 HA1631S01 Input Offset Voltage vs. Supply Voltage Ta = 25C Input Offset Voltage VIO (mV) Output Low Voltage VOL (V) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0 4 3 VIN = VDD/2 2 1 0 -1 -2 -3 -4 0 1 2 3 4 5 6 10 20 30 40 Output Sink Current IOSINK (mA) Supply Voltage VDD (V) Rev.1.00, 2003.08.08, page 7 of 22 HA1631S01/02/03/04 Series Figure 1-8 HA1631S01 Common Mode Input Voltage vs. Ambient Temperature 2.5 2.0 1.5 1.0 0.5 0.0 -0.5 -1.0 -50 VDD = 3.0V VCM- Common Mode Input Voltage Range VCM+ Input Offset Voltage VIO (mV) 4 3 2 1 0 -1 -2 -3 VDD = 1.8V, VIN = 0.9V VDD = 3.0V, VIN = 1.5V VDD = 5.0V, VIN = 2.5V -4 -50 -25 0 25 50 75 100 Common Mode Input Voltage VCM (V) Figure 1-7 HA1631S01 Input Offset Voltage vs. Ambient Temperature -25 0 25 50 75 100 Ambient Temperature Ta (C) Common Mode Rejection Ratio CMRR (dB) Ambient Temperature Ta (C) Figure 1-10 HA1631S01 Common Mode Rejection Ratio vs. Input Voltage 120 100 80 60 40 Ta = 25C Power Supply Rejection Ratio PSRR (dB) Figure 1-9 HA1631S01 Power Supply Rejection Ratio vs. Supply Voltage 120 100 80 60 40 20 0 1 Ta = 25C VIN = 0.0V VDD = 0.0 to 2.75V VSS = 0.0 to -2.75V VDD & VSS Simultaneous Sweep 20 VDD = 1.5V VSS = -1.5V 2 3 4 5 6 7 0 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 Supply Voltage VDD to VSS (V) Figure 1-11 HA1631S01 Input Bias Current vs. Ambient Temperature VDD = 3.0V Input Voltage VIN (V) Figure 1-12 HA1631S01 Input Bias Current vs. Input Voltage Ta = 25C VDD = 3.0V Input Bias Current IIB (pA) 100 0 Input Bias Current IIB (pA) 200 200 100 0 -100 -200 -50 -100 -200 0.0 -25 0 25 50 75 100 0.5 1.0 1.5 2.0 2.5 3.0 Ambient Temperature Ta (C) Input Voltage VIN (V) Rev.1.00, 2003.08.08, page 8 of 22 HA1631S01/02/03/04 Series Figure 1-13 HA1631S01 Falling Time vs. Ambient Temperature Figure 1-14 HA1631S01 Rising Time vs. Ambient Temperature 18 16 70 Falling Time tf (ns) Rising Time tr (ns) 14 12 10 8 6 4 2 0 -50 -25 0 VDD = 1.8V VDD = 5.5V 60 50 40 30 20 10 0 -50 -25 0 25 VDD = 3.0V VDD = 5.5V VDD = 1.8V VDD = 3.0V 25 50 75 100 50 75 100 Ambient Temperature Ta (C) Figure 1-15 HA1631S01 Falling Time vs. Capacitor Load Ambient Temperature Ta (C) Figure 1-16 HA1631S01 Rising Time vs. Capacitor Load Ta = 25C 140 140 Falling Time tf (ns) Rising Time tr (ns) 120 100 80 60 40 20 0 0 Ta = 25C VDD = 2.0V VSS = -1.0V VIN+ = 0.1Vp-p Overdrive 120 VDD = 2.0V 100 VIN+ = 0.1Vp-p 80 60 40 20 0 0 10 20 30 40 50 Overdrive VSS = -1.0V 10 20 30 40 50 Capacitor Load CL (pF) Figure 1-17 HA1631S01 Output Low Voltage vs. Resistor Load Ta = 25C VDD = 3.0V Capacitor Load CL (pF) Figure 1-18 HA1631S01 Output High Voltage vs. Resistor Load 2.5 2.0 1.5 1.0 0.5 Output High Voltage VOH (V) Output Low Voltage VOL (V) 3.0 3.0 2.5 2.0 1.5 1.0 0.5 Ta = 25C VDD = 3.0V 0.0 1.0E+01 1.0E+03 1.0E+05 0.0 1.0E+01 1.0E+03 1.0E+05 Resistor Load RL () Resistor Load RL () Rev.1.00, 2003.08.08, page 9 of 22 HA1631S01/02/03/04 Series Figure 1-19 HA1631S01 Rising Time, tr (Overdrive = 0.1Vp-p) VDD Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive VDD Figure 1-20 HA1631S01 Falling Time, tf (Overdrive = 0.1Vp-p) GND GND Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive Figure 1-21 HA1631S01 TPLH Transient Response (Overdrive = 0.1Vp-p) Input Voltage Figure 1-22 HA1631S01 TPHL Transient Response (Overdrive = 0.1Vp-p) Input Voltage CH1 GND Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive Output Voltage CH1 GND Output Voltage Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive CH2 GND CH2 GND Rev.1.00, 2003.08.08, page 10 of 22 HA1631S01/02/03/04 Series Figure 2-1 HA1631S02 Supply Current vs. Supply Voltage (Output High) Supply Current IDD (A) Ta = 25C VIN+ = 1.0V VIN- = 0.0V 70 Supply Current IDD (A) 70 Figure 2-2 HA1631S02 Supply Current vs. Supply Voltage (Output Low) Ta = 25C 60 50 40 30 20 10 0 0 60 VIN+ = 0.0V 50 40 30 20 10 0 0 1 2 3 4 5 6 VIN- = 1.0V 1 2 3 4 5 6 Supply Voltage VDD (V) Figure 2-3 HA1631S02 Supply Current vs. Ambient Temperature VDD = 5.0V VDD = 3.0V VDD = 1.8V Supply Voltage VDD (V) Figure 2-4 HA1631S02 Output High Voltage vs. Output Source Current 3.5 3.0 2.5 2.0 1.5 1.0 0.5 Ta = 25C VDD = 3.0V 75 50 25 0 -50 Output High Voltage VOH (V) 100 Supply Current IDD (A) -25 0 25 50 75 100 0.0 0 10 20 30 40 Ambient Temperature Ta (C) Figure 2-5 HA1631S02 Output Low Voltage vs. Output Sink Current Ta = 25C VDD = 3.0V Output Source Current IOSOURCE (mA) Figure 2-6 HA1631S02 Input Offset Voltage vs. Supply Voltage Ta = 25C Input Offset Voltage VIO (mV) Output Low Voltage VOL (V) 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0 4 3 VIN = VDD/2 2 1 0 -1 -2 -3 -4 1 2 3 4 5 6 10 20 30 40 Output Sink Current IOSINK (mA) Supply Voltage VDD (V) Rev.1.00, 2003.08.08, page 11 of 22 HA1631S01/02/03/04 Series Figure 2-8 HA1631S02 Common Mode Input Voltage vs. Ambient Temperature 2.5 2.0 1.5 1.0 0.5 0.0 -0.5 -1.0 -50 VDD = 3.0V VCM- Common Mode Input Voltage Range VCM+ Input Offset Voltage VIO (mV) 4 3 2 1 0 -1 -2 -3 VDD = 1.8V, VIN = 0.9V VDD = 3.0V, VIN = 1.5V VDD = 5.0V, VIN = 2.5V -4 -50 -25 0 25 50 75 100 Common Mode Input Voltage VCM (V) Figure 2-7 HA1631S02 Input Offset Voltage vs. Ambient Temperature -25 0 25 50 75 100 Ambient Temperature Ta (C) Common Mode Rejection Ratio CMRR (dB) Ambient Temperature Ta (C) Figure 2-10 HA1631S02 Common Mode Rejection Ratio vs. Input Voltage Power Supply Rejection Ratio PSRR (dB) Figure 2-9 HA1631S02 Power Supply Rejection Ratio vs. Supply Voltage 120 100 80 60 40 20 0 1 Ta = 25C VIN = 0.0V VDD = 0.0 to 2.75V VSS = 0.0 to -2.75V VDD & VSS Simultaneous Sweep 120 100 80 60 40 Ta = 25C 20 VDD = 1.5V VSS = -1.5V 2 3 4 5 6 7 0 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 Supply Voltage VDD to VSS (V) Figure 2-11 HA1631S02 Input Bias Current vs. Ambient Temperature VDD = 3.0V Input Voltage VIN (V) Figure 2-12 HA1631S02 Input Bias Current vs. Input Voltage Ta = 25C VDD = 3.0V Input Bias Current IIB (pA) Input Bias Current IIB (pA) 200 100 0 200 100 0 -100 -200 -50 -100 -200 0.0 -25 0 25 50 75 100 0.5 1.0 1.5 2.0 2.5 3.0 Ambient Temperature Ta (C) Input Voltage VIN (V) Rev.1.00, 2003.08.08, page 12 of 22 HA1631S01/02/03/04 Series Figure 2-13 HA1631S02 Falling Time vs. Ambient Temperature Figure 2-14 HA1631S02 Rising Time vs. Ambient Temperature VDD = 5.5V 20 18 16 14 12 10 8 6 4 2 0 -50 VDD = 1.8V VDD = 3.0V VDD = 5.5V -25 0 25 50 75 100 20 18 16 14 12 10 8 6 4 2 0 -50 Falling Time tf (ns) Rising Time tr (ns) VDD = 3.0V VDD = 1.8V -25 0 25 50 75 100 Ambient Temperature Ta (C) Figure 2-15 HA1631S02 Falling Time vs. Capacitor Load Ambient Temperature Ta (C) Figure 2-16 HA1631S02 Rising Time vs. Capacitor Load Ta = 25C 120 120 Falling Time tf (ns) Rising Time tr (ns) 100 80 60 40 20 0 0 Ta = 25C VDD = 2.0V VSS = -1.0V VIN+ = 0.1Vp-p Overdrive 100 VDD = 2.0V Overdrive VSS = -1.0V 80 VIN+ = 0.1Vp-p 60 40 20 0 0 10 20 30 40 50 10 20 30 40 50 Capacitor Load CL (pF) Figure 2-17 HA1631S02 Output Low Voltage vs. Resistor Load Ta = 25C VDD = 3.0V Capacitor Load CL (pF) Figure 2-18 HA1631S02 Output High Voltage vs. Resistor Load 2.5 2.0 1.5 1.0 0.5 Output High Voltage VOH (V) Output Low Voltage VOL (V) 3.0 3.0 2.5 2.0 1.5 1.0 0.5 Ta = 25C VDD = 3.0V 0.0 1.0E+01 1.0E+03 1.0E+05 0.0 1.0E+01 1.0E+03 1.0E+05 Resistor Load RL () Resistor Load RL () Rev.1.00, 2003.08.08, page 13 of 22 HA1631S01/02/03/04 Series Figure 2-19 HA1631S02 Rising Time, tr (Overdrive = 0.1Vp-p) VDD Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive VDD Figure 2-20 HA1631S02 Falling Time, tf (Overdrive = 0.1Vp-p) GND GND Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive Figure 2-21 HA1631S02 TPLH Transient Response (Overdrive = 0.1Vp-p) Input Voltage Figure 2-22 HA1631S02 TPHL Transient Response (Overdrive = 0.1Vp-p) Input Voltage CH1 GND Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive Output Voltage CH1 GND Output Voltage Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive CH2 GND CH2 GND Rev.1.00, 2003.08.08, page 14 of 22 HA1631S01/02/03/04 Series Figure 3-1 HA1631S03 Supply Current vs. Supply Voltage (Output High) Supply Current IDD (A) Ta = 25C VIN+ = 1.0V VIN- = 0.0V 7.0 Supply Current IDD (A) 7.0 Figure 3-2 HA1631S03 Supply Current vs. Supply Voltage (Output Low) Ta = 25C 6.0 5.0 4.0 3.0 2.0 1.0 0.0 0 6.0 VIN+ = 0.0V 5.0 4.0 3.0 2.0 1.0 0.0 0 1 2 3 4 5 6 VIN- = 1.0V 1 2 3 4 5 6 Supply Voltage VDD (V) Figure 3-3 HA1631S03 Supply Current vs. Ambient Temperature Output Low Voltage VOL (V) VDD = 5.0V VDD = 3.0V VDD = 1.8V Supply Voltage VDD (V) Figure 3-4 HA1631S03 Output Low Voltage vs. Output Sink Current Ta = 25C 10.0 Supply Current IDD (A) 3.5 3.0 VDD = 3.0V 2.5 2.0 1.5 1.0 0.5 0.0 0 10 20 30 40 7.5 5.0 2.5 0.0 -50 -25 0 25 50 75 100 Ambient Temperature Ta (C) Figure 3-5 HA1631S03 Input Offset Voltage vs. Supply Voltage Ta = 25C VIN = VDD/2 Output Sink Current IOSINK (mA) Figure 3-6 HA1631S03 Input Offset Voltage vs. Ambient Temperature Input Offset Voltage VIO (mV) Input Offset Voltage VIO (mV) 4 3 2 1 0 -1 -2 -3 -4 0 4 3 2 1 0 -1 -2 -3 -4 -50 -25 0 25 50 75 100 VDD = 1.8V, VIN = 0.9V VDD = 3.0V, VIN = 1.5V VDD = 5.0V, VIN = 2.5V 1 2 3 4 5 6 Supply Voltage VDD (V) Ambient Temperature Ta (C) Rev.1.00, 2003.08.08, page 15 of 22 HA1631S01/02/03/04 Series Figure 3-7 HA1631S03 Common Mode Input Voltage vs. Ambient Temperature 2.5 2.0 1.5 1.0 0.5 0.0 -0.5 -1.0 -50 VDD = 3.0V VCM- Common Mode Input Voltage Range VCM+ Power Supply Rejection Ratio PSRR (dB) Common Mode Input Voltage VCM (V) 120 100 80 60 40 20 0 Figure 3-8 HA1631S03 Power Supply Rejection Ratio vs. Supply Voltage Ta = 25C VIN = 0.0V VDD = 0.0 to 2.75V VSS = 0.0 to -2.75V VDD & VSS Simultaneous Sweep -25 0 25 50 75 100 1 2 3 4 5 6 7 Ambient Temperature Ta (C) Supply Voltage VDD to VSS (V) Figure 3-10 HA1631S03 Input Bias Current vs. Ambient Temperature VDD = 3.0V Common Mode Rejection Ratio CMRR (dB) 100 80 60 40 Ta = 25C Input Bias Current IIB (pA) -1.0 -0.5 0.0 0.5 1.0 120 Figure 3-9 HA1631S03 Common Mode Rejection Ratio vs. Input Voltage 200 100 0 -100 -200 -50 20 VDD = 1.5V VSS = -1.5V 0 -2.0 -1.5 -25 0 25 50 75 100 Input Voltage VIN (V) Figure 3-11 HA1631S03 Input Bias Current vs. Input Voltage Ambient Temperature Ta (C) Figure 3-12 HA1631S03 Falling Time vs. Ambient Temperature VDD = 1.8V Input Bias Current IIB (pA) 200 100 0 14 Falling Time tf (ns) Ta = 25C VDD = 3.0V 12 10 8 6 4 2 0 -50 -100 -200 0.0 VDD = 3.0V VDD = 5.5V 0.5 1.0 1.5 2.0 2.5 3.0 -25 0 25 50 75 100 Input Voltage VIN (V) Ambient Temperature Ta (C) Rev.1.00, 2003.08.08, page 16 of 22 HA1631S01/02/03/04 Series Figure 3-13 HA1631S03 Falling Time vs. Capacitor Load Output Low Voltage VOL (V) Ta = 25C VDD = 2.0V VSS = -1.0V VIN+ = 0.1Vp-p Overdrive 45 40 Falling Time tf (ns) 3.0 Figure 3-14 HA1631S03 Output Low Voltage vs. Resistor Load Ta = 25C 35 30 25 20 15 10 5 0 0 2.5 VDD = 3.0V 2.0 1.5 1.0 0.5 0.0 1.0E+01 1.0E+03 1.0E+05 15 10 20 30 40 50 Capacitor Load CL (pF) Figure 3-15 HA1631S03 Falling Time, tf VDD Resistor Load RL () Figure 3-16 HA1631S03 TPHL Transient Response (Overdrive = 0.1Vp-p) Input Voltage CH1 GND Output Voltage Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive GND CH2 GND Figure 3-17 HA1631S03 TPHL Transient Response (Overdrive = 0.1Vp-p) Input Voltage CH1 GND Output Voltage Ta = 25C VDD = 3.0V CL = 15pF VIN+ = 0.1Vp-p Overdrive CH2 GND Rev.1.00, 2003.08.08, page 17 of 22 HA1631S01/02/03/04 Series Figure 4-1 HA1631S04 Supply Current vs. Supply Voltage (Output High) Supply Current IDD (A) Ta = 25C VIN+ = 1.0V VIN- = 0.0V 70 Supply Current IDD (A) 70 Figure 4-2 HA1631S04 Supply Current vs. Supply Voltage (Output Low) Ta = 25C 60 50 40 30 20 10 0 0 60 VIN+ = 0.0V 50 40 30 20 10 0 0 1 2 3 4 5 6 VIN- = 1.0V 1 2 3 4 5 6 Supply Voltage VDD (V) Figure 4-3 HA1631S04 Supply Current vs. Ambient Temperature Output Low Voltage VOL (V) VDD = 5.0V VDD = 3.0V VDD = 1.8V Supply Voltage VDD (V) Figure 4-4 HA1631S04 Output Low Voltage vs. Output Sink Current Ta = 25C 100 Supply Current IDD (A) 3.5 3.0 VDD = 3.0V 2.5 2.0 1.5 1.0 0.5 0.0 0 10 20 30 40 75 50 25 0 -50 -25 0 25 50 75 100 Ambient Temperature Ta (C) Figure 4-5 HA1631S04 Input Offset Voltage vs. Supply Voltage Ta = 25C VIN = VDD/2 Output Sink Current IOSINK (mA) Figure 4-6 HA1631S04 Input Offset Voltage vs. Ambient Temperature Input Offset Voltage VIO (mV) Input Offset Voltage VIO (mV) 4 3 2 1 0 -1 -2 -3 -4 0 4 3 2 1 0 -1 -2 -3 -4 -50 -25 0 25 50 75 100 VDD = 1.8V, VIN = 0.9V VDD = 3.0V, VIN = 1.5V VDD = 5.0V, VIN = 2.5V 1 2 3 4 5 6 Supply Voltage VDD (V) Ambient Temperature Ta (C) Rev.1.00, 2003.08.08, page 18 of 22 HA1631S01/02/03/04 Series Figure 4-7 HA1631S04 Common Mode Input Voltage vs. Ambient Temperature 3.0 VDD = 3.0V Power Supply Rejection Ratio PSRR (dB) Common Mode Input Voltage VCM (V) 120 100 80 60 40 20 0 Figure 4-8 HA1631S04 Power Supply Rejection Ratio vs. Supply Voltage 2.5 2.0 1.5 1.0 0.5 0.0 -0.5 -50 -25 0 25 50 75 100 VCM+ Common Mode Input Voltage Range VCM- Ta = 25C VIN = 0.0V VDD = 0.0 to 2.75V VSS = 0.0 to -2.75V VDD & VSS Simultaneous Sweep 1 2 3 4 5 6 7 Ambient Temperature Ta (C) Supply Voltage VDD to VSS (V) Figure 4-10 HA1631S04 Input Bias Current vs. Ambient Temperature VDD = 3.0V Common Mode Rejection Ratio CMRR (dB) 100 80 60 40 Ta = 25C Input Bias Current IIB (pA) -1.0 -0.5 0.0 0.5 1.0 120 Figure 4-9 HA1631S04 Common Mode Rejection Ratio vs. Input Voltage 200 100 0 -100 -200 -50 20 VDD = 1.5V VSS = -1.5V 0 -2.0 -1.5 -25 0 25 50 75 100 Input Voltage VIN (V) Figure 4-11 HA1631S04 Input Bias Current vs. Input Voltage Ambient Temperature Ta (C) Figure 4-12 HA1631S04 Falling Time vs. Ambient Temperature VDD = 1.8V Input Bias Current IIB (pA) 200 100 0 7.0 Falling Time tf (ns) Ta = 25C VDD = 3.0V 6.0 5.0 4.0 3.0 2.0 1.0 0.0 -50 VDD = 5.5V VDD = 3.0V -100 -200 0.0 0.5 1.0 1.5 2.0 2.5 3.0 -25 0 25 50 75 100 Input Voltage VIN (V) Ambient Temperature Ta (C) Rev.1.00, 2003.08.08, page 19 of 22 HA1631S01/02/03/04 Series Figure 4-13 HA1631S04 Falling Time vs. Capacitor Load Output Low Voltage VOL (V) Ta = 25C VDD = 2.0V VSS = -1.0V VIN+ = 0.1Vp-p Overdrive 120 Falling Time tf (ns) 3.0 Figure 4-14 HA1631S04 Output Low Voltage vs. Resistor Load Ta = 25C 100 80 60 40 20 0 0 2.5 VDD = 3.0V 2.0 1.5 1.0 0.5 0.0 1.0E+01 1.0E+03 1.0E+05 10 20 30 40 50 Capacitor Load CL (pF) Figure 4-15 HA1631S04 Falling Time, tf (Overdrive = 0.1Vp-p) VDD CH1 GND Resistor Load RL () Figure 4-16 HA1631S04 TPHL Transient Response (Overdrive = 0.1Vp-p) Input Voltage Output Voltage Ta = 25C VDD = 3.0V CL = 15pF RL = 10k VIN+ = 0.1Vp-p Overdrive Ta = 25C VDD = 3.0V CL = 15pF RL = 10k VIN+ = 0.1Vp-p Overdrive GND CH2 GND Figure 4-17 HA1631S04 TPHL Transient Response (Overdrive = 0.1Vp-p) Input Voltage CH1 GND Output Voltage Ta = 25C VDD = 3.0V CL = 15pF RL = 10k VIN+ = 0.1Vp-p Overdrive CH2 GND Rev.1.00, 2003.08.08, page 20 of 22 HA1631S01/02/03/04 Series Mark Indication (1) (2) HA1631S01CM HA1631S02CM HA1631S03CM HA1631S04CM HA1631S01LP HA1631S01LP HA1631S01LP HA1631S01LP (1) 0 0 0 0 (2) A B C D Rev.1.00, 2003.08.08, page 21 of 22 HA1631S01/02/03/04 Series Package Information Unit: mm (0.65) (0.65) (0.425) 1.3 0.2 0.15- 0.05 + 0.1 1.25 0.1 2.1 0.3 0 - 0.1 2.0 0.2 0.9 0.1 (0.2) (0.425) 5 - 0.2 0.05 Package Code JEDEC JEITA Mass (reference value) CMPAK-5V -- Conforms 0.006 g Unit: mm 1.9 0.2 0.95 0.95 0.16 + 0.1 - 0.05 0.6 + 0.2 - 0.1 5 - 0.4 - 0.05 2.9 0.2 + 0.1 0.3 + 0.2 1.1 - 0.1 0.6 1.6 0.2 2.8 + 0.3 - 0 - 0.1 Package Code JEDEC JEITA Mass (reference value) MPAK-5 -- -- 0.015 g Rev.1.00, 2003.08.08, page 22 of 22 Sales Strategic Planning Div. Keep safety first in your circuit designs! Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. RENESAS SALES OFFICES Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501 Renesas Technology Europe Limited. Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900 Renesas Technology Europe GmbH Dornacher Str. 3, D-85622 Feldkirchen, Germany Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11 Renesas Technology Hong Kong Ltd. 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2375-6836 Renesas Technology Taiwan Co., Ltd. FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. 26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 http://www.renesas.com (c) 2003. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon 1.0 |
Price & Availability of HA1631S01
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |