 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order Number: MPC972/D Rev 6, 09/2001 Low Voltage PLL Clock Driver The MPC972 is a 3.3 V compatible, PLL based clock driver device targeted for high performance CISC or RISC processor based systems. With output frequencies of up to 125 MHz and skews of 550 ps the MPC972 is ideally suited for most synchronous systems. The device offers twelve low skew outputs plus a feedback and sync output for added flexibility and ease of system implementation. * Fully Integrated PLL * Output Frequency up to 125 MHz * Compatible with PowerPC and Pentium Microprocessors * LQFP Packaging * 3.3 V VCC MPC972 LOW VOLTAGE PLL CLOCK DRIVER * 100 ps Typical Cycle-to-Cycle Jitter The MPC972 features an extensive level of frequency programmability between the 12 outputs as well as the input vs output relationships. Using the select lines output frequency ratios of 1:1, 2:1, 3:1, 3:2, 4:1, 4:3, 5:1, 5:2, 5:3, 6:1 and 6:5 between outputs can be realized by pulsing low one clock edge prior to the coincident edges of the Qa and Qc outputs. The Sync output will indicate when the coincident rising edges of the above relationships will occur. The selectability of the feedback frequency is independent of the output frequencies, this allows for very flexible programming of the input reference vs output frequency relationship. The output frequencies can be either odd or even multiples of the input SCALE 2:1 reference. In addition the output frequency can be less than the input frequency for applications where a frequency needs to be reduced by a FA SUFFIX non-binary factor. The Power-On Reset ensures proper programming if the 52-LEAD LQFP PACKAGE frequency select pins are set at power up. If the fselFB2 pin is held high, it CASE 848D-03 may be necessary to apply a reset after power-up to ensure synchronization between the QFB output and the other outputs. The internal power-on reset is designed to provide this function, but with power-up conditions being dependent, it is difficult to guarantee. All other conditions of the fsel pins will automatically synchronize during PLL lock acquisition. The MPC972 offers a very flexible output enable/disable scheme. This enable/disable scheme helps facilitate system debug as well as provide unique opportunities for system power down schemes to meet the requirements of "green" class machines. The MPC972 allows for the enabling of each output independently via a serial input port. When disabled or "frozen" the outputs will be locked in the "LOW" state, however the internal state machines will continue to run. Therefore when "unfrozen" the outputs will activate synchronous and in phase with those outputs which were not frozen. The freezing and unfreezing of outputs occurs only when they are already in the "LOW" state, thus the possibility of runt pulse generation is eliminated. A power-on reset will ensure that upon power up all of the outputs will be active. Note that all of the control inputs on the MPC972 have internal pull-up resistors. The MPC972 is fully 3.3 V compatible and requires no external loop filter components. All inputs accept LVCMOS/LVTTL compatible levels while the outputs provide LVCMOS levels with the capability to drive 50 transmission lines. For series terminated lines each MPC972 output can drive two 50 lines in parallel thus effectively doubling the fanout of the device. The MPC972 can consume significant power in some configurations. Users are encouraged to review Application Note AN1545/D in the Advanced Clock Drivers Device Data book (DL207/D) for a discussion on the thermal issues with the MPC family of clock drivers. PowerPC is a trademark of International Business Machines Corporation. Pentium is a trademark of Intel Corporation. Motorola, Inc. 2001 t MPC972 fselFB0 27 26 25 24 23 22 21 fselFB1 QSync GNDO Qc0 VCCO Qc1 fselc0 fselc1 Qc2 VCCO Qc3 GNDO Inv_Clk 20 19 18 17 16 15 14 1 2 3 4 5 6 7 8 9 10 11 12 13 VCCA fselc0 0 1 0 1 Ext_FB GNDO GNDO GNDO VCCO VCCO VCCI 28 xtal2 QFB 29 xtal1 Qb0 Qb1 Qb2 Qb3 32 39 fselb1 fselb0 fsela1 fsela0 Qa3 VCCO Qa2 GNDO Qa1 VCCO Qa0 GNDO VCO_Sel 40 41 42 43 44 45 46 47 48 49 50 51 52 38 37 36 35 34 33 31 30 MPC972 Ref_Sel TClk_Sel fselFB2 MR/OE GNDI TClk0 Frz_Data All inputs have internal pull-up resistors (appr. 50 K) except for the xtal1 and xtal2 pins. Figure 1. 52-Lead Pinout (Top View) FUNCTION TABLE 1 fsela1 0 0 1 1 fsela0 0 1 0 1 Qa /4 /6 /8 /12 fselb1 0 0 1 1 fselb0 0 1 0 1 Qb /4 /6 /8 /10 fselc1 0 0 1 1 Qc /2 /4 /6 /8 FUNCTION TABLE 2 *fselFB2 0 0 0 0 fselFB1 0 0 1 1 fselFB0 0 1 0 1 QFB /4 /6 /8 /10 PLL_EN Frz_Clk FUNCTION TABLE 3 Control Pin VCO_Sel Ref_Sel TCLK_Sel PLL_En MR/OE Inv_Clk Logic `0' VCO/2 TCLK TCLK0 Bypass PLL Master Reset/Output Hi-Z Non-Inverted Qc2, Qc3 Logic `1' VCO Xtal (PECL) TCLK1 Enable PLL Enable Outputs Inverted Qc2, Qc3 1 0 0 /8 1 0 1 /12 1 1 0 /16 1 1 1 /20 *If the fselFB2 is 1, it may be necessary to apply a reset after power up to ensure synchronization between QFB and the other inputs. 2 TClk1 MOTOROLA MPC972 xtal1 xtal2 VCO_Sel PLL_En REF_SEL Sync Frz Qa0 Qa1 Qa2 Qa3 DQ Sync Frz Qb0 Qb1 Qb2 Qb3 fselFB2 TCLK0 TCLK1 TCLK_Sel Ext_FB 0 1 PHASE DETECTOR LPF VCO 0 1 DQ MR/OE POWER ON RESET /4, /6, /8, /12 /4, /6, /8, /10 /2, /4, /6, /8 fsela0:1 fselb0:1 fselc0:1 fselFB0:1 2 2 2 2 Sync Pulse Data Generator /4, /6, /8, /10 0 1 DQ Qc0 Sync Frz Sync Frz Qc1 Qc2 Qc3 QFB DQ /2 DQ DQ Sync Frz QSync Frz_Clk Frz_Data Inv_Clk Output Disable Circuitry 12 Figure 2. Logic Diagram MOTOROLA 3 MPC972 fVCO 1:1 Mode Qa Qc Sync 2:1 Mode Qa Qc Sync 3:1 Mode Qc(/2) Qa(/6) Sync 3:2 Mode Qa(/4) Qc(/6) Sync 4:1 Mode Qc(/2) Qa(/8) Sync 4:3 Mode Qa(/6) Qc(/8) Sync 6:1 Mode Qa(/12) Qc(/2) Sync Figure 3. Timing Diagrams 4 MOTOROLA MPC972 ABSOLUTE MAXIMUM RATINGS* Symbol VCC VI IIN TStor Supply Voltage Input Voltage Input Current Storage Temperature Range -40 Parameter Min -0.3 -0.3 Max 4.6 VCC + 0.3 20 125 Unit V V mA C * Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute-maximum-rated conditions is not implied. THERMAL CHARACTERISTICS Proper thermal management is critical for reliable system operation. This is especially true for high fanout and high drive capability products. Generic thermal information is available for the Motorola Clock Driver products. The means of calculating die power, the corresponding die temperature and the relationship to long-term reliability is addressed in the Motorola application note AN1545. DC CHARACTERISTICS (Note 3.; TA = 0 to 70C; VCC = 3.3 V 5%) Symbol VCCA VIH VIL VOH VOL IIN ICC ICCA CIN Cpd Characteristic Analog VCC Voltage Input HIGH Voltage Input LOW Voltage Output HIGH Voltage Output LOW Voltage Input Current Maximum Quiescent Supply Current Analog VCC Current Input Capacitance Power Dissipation Capacitance 25 190 15 2.4 0.5 120 215 20 4 Min 2.935 2.0 Typ Max VCC 3.6 0.8 Unit V V V V V A mA mA pF pF Per Output IOH = -20 mA (Note 1.) IOL = 20 mA (Note 1.) Note 2. All VCC PIns Condition 1. The MPC972 outputs can drive series or parallel terminated 50 (or 50 to VCC/2) transmission lines on the incident edge (see Applications Info section). 2. Inputs have pull-up/pull-down resistors which affect input current. 3. Special thermal handling may be required in some configurations. PLL INPUT REFERENCE CHARACTERISTICS (TA = 0 to 70C) Symbol tr, tf fref frefDC txtal Characteristic TCLK Input Rise/Falls Reference Input Frequency Reference Input Duty Cycle Crystal Oscillator Frequency Note 4. 25 10 Min Max 3.0 100 Note 4. 75 25 Unit ns MHz % MHz Note 5. Condition 4. Maximum input reference frequency is limited by the VCO lock range and the feedback divider or 100MHz, minimum input reference frequency is limited by the VCO lock range and the feedback divider. 5. See Applications Info section for more crystal information. MOTOROLA 5 MPC972 AC CHARACTERISTICS (TA = 0 to 70C; VCC = 3.3V 5%) Symbol tr, tf tpw tpd tos fVCO fmax Characteristic Output Rise/Fall Time Output Duty Cycle SYNC to Feedback Propagation Delay Output-to-Output Skew VCO Lock Range Maximum Output Frequency Q (/2) Q (/4) Q (/6) Q (/8) 100 2 2 8 10 10 20 200 TCLK0 TCLK1 Min 0.15 tCYCLE/2 -750 -270 -330 tCYCLE/2 500 130 70 Typ Max 1.2 tCYCLE/2 +750 530 470 550 480 125 120 80 60 Unit ns ps ps ps MHz MHz Note 6. Condition 0.8 to 2.0V, Note 6. Note 6. Notes 6., 7.; QFB = /8 Note 6. tjitter tPLZ, tPHZ tPZL, tPZH tlock fMAX Cycle-to-Cycle Jitter (Peak-to-Peak) Output Disable Time Output ENable TIme Maximum PLL Lock Time Maximum Frz_Clk Frequency ps ns ns ms MHz Note 6. Note 6. Note 6. 6. 50 transmission line terminated into VCC/2. 7. tpd is specified for a 50MHz input reference. The window will shrink/grow proportionally from the minimum limit with shorter/longer input reference periods. The tpd does not include jitter. APPLICATIONS INFORMATION Programming the MPC972 The MPC972 is one of the most flexible frequency programming devices in the Motorola timing solution portfolio. With three independent banks of four outputs as well as an independent PLL feedback output the total number of possible configurations is too numerous to tabulate. Table 1 tabulates the various selection possibilities for the three banks of outputs. The divide numbers presented in the table represent the divider applied to the output of the VCO for that bank of outputs. To determine the relationship between the three banks the three divide ratios would be compared. For instance if a frequency relationship of 5:3:2 was desired the following selection could be made. The Qb outputs could be set to /10, the Qa outputs to /6 and the Qc outputs to /4. With this output divide selection the desired 5:3:2 relationship would be generated. For situations where the VCO will run at relatively low frequencies the PLL may not be stable for the desired divide ratios. For these circumstances the VCO_Sel pin allows for an extra /2 to be added into the clock path. When asserted this pin will maintain the desired output relationships, but will provide an enhanced lock range for the PLL. Once the output frequency relationship is set and the VCO is in its stable range the feedback output would be programmed to match the input reference frequency. The MPC972 offers only an external feedback to the PLL. A separate feedback output is provided to optimize the flexibility of the device. If in the example above the input reference frequency was equal to the lowest output frequency the feedback output would be set in the /10 mode. If the input needed to be half the lowest frequency output the fselFB2 input could be asserted to halve the feedback frequency. This action multiplies the output frequencies by two relative to the input reference frequency. With 7 unique feedback divide capabilities there is a tremendous amount of flexibility. Again assume the above 5:3:2 relationship is needed with the highest frequency output equal to 100 MHz. If one was also constrained because the only reference frequency available was 50 MHz the setup in Figure 6 could be used. The MPC972 provides the 100, 66 and 40 MHz outputs all synthesized from the 50 MHz source. With its multitude of divide ratio capabilities the MPC972 can generate almost any frequency from a standard, common frequency already present in a design. Figure 7 and Figure 8 illustrate a few more examples of possible MPC972 configurations. The MPC972 has one more programming feature added to its arsenal. The Inv_Clk input pin when asserted will invert the Qc2 and Qc3 outputs. This inversion will not affect the output-output skew of the device. This inversion allows for the development of 180 phase shifted clocks. This output could also be used as a feedback output to the MPC972 or a second PLL device to generate early or late clocks for a specific design. Figure 9 illustrates the use of two MPC972's to generate two banks of clocks with one bank divided by 2 and delayed by 180 relative to the first. 6 MOTOROLA MPC972 SYNC Output Description In situations where output frequency relationships are not integer multiples of each other there is a need for a signal for system synchronization purposes. The SYNC output of the MPC972 is designed to specifically address this need. The MPC972 monitors the relationship between the Qa and the Qc banks of outputs. It provides a low going pulse, one period in duration, one period prior to the coincident rising edges of the Qa and Qc outputs. The duration and the placement of the pulse is dependent on the higher of the Qa and Qc output frequencies. The timing diagrams in the data sheet show the various waveforms for the SYNC output. Note that the SYNC output is defined for all possible combinations of the Qa and Qc outputs even though under some relationships the lower frequency clock could be used as a synchronizing signal. 1. Programmable Output Frequency Relationships (VCO_Sel = `1') fsela1 0 0 1 1 fsela0 0 1 0 1 Qa VCO/4 VCO/6 VCO/8 VCO/12 fselb1 0 0 1 1 fselb0 0 1 0 1 Qb VCO/4 VCO/6 VCO/8 VCO/10 fselc1 0 0 1 1 fselc0 0 1 0 1 Qc VCO/2 VCO/4 VCO/6 VCO/8 2. Programmable Output Frequency Relationships (VCO_Sel = `1') fselFB2 0 0 0 0 1 1 1 1 400 300 200 100 0 -100 -200 -300 -400 Qc3 Qc2 Qc1 Qc0 Qb3 Qb2 Qb1 Qb0 Qa3 Qa2 Qa1 Qa0 ps fselFB1 0 0 1 1 0 0 1 1 fselFB0 0 1 0 1 0 1 0 1 QFB VCO/4 VCO/6 VCO/8 VCO/10 VCO/8 VCO/12 VCO/16 VCO/20 Figure 4. Typical Skews Relative to QFB 60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 VCO/8 1 I/O Jitter (ps) VCO/4 VCO/6 30 40 50 60 70 80 90 100 110 Reference Clock Frequency (MHz) Figure 5. Typical Phase Jitter versus Reference Frequency I/O Jitter MOTOROLA 7 MPC972 MPC972 0' 0' 1' 1' 0' 1' 0' 1' 0' fsela0 fsela1 fselb0 fselb1 fselc0 fselc1 fselFB0 fselFB1 fselFB2 Qa Qb Qc QFB 4 4 4 100 MHz 40 MHz 66.66 MHz 50 MHz 0' 0' 0' 0' 1' 1' 1' 1' 0' fsela0 fsela1 fselb0 fselb1 fselc0 fselc1 fselFB0 fselFB1 fselFB2 MPC972 Qa Qb Qc QFB 4 4 4 60 MHz (Processor) 60 MHz (Processor) 30 MHz (PCI) 24 MHz (Floppy Disk Clk) 50 MHz Input Ref Ext_FB 24 MHz Input Ref Ext_FB VCO = 400 MHz Figure 6. Programming Configuration Example Figure 7. Generating Pentium Clocks from Floppy Clock MPC972 1' 1' 0' 1' 1' 1' 1' 1' 1' fsela0 fsela1 fselb0 fselb1 fselc0 fselc1 fselFB0 fselFB1 fselFB2 Qa Qb Qc QFB 4 4 4 33 MHz (PCI) 50 MHz (Processor) 50 MHz (Processor) 20 MHz (Ethernet) 20 MHz Input Ref Ext_FB Figure 8. Generating MPC604 Clocks from Ethernet Clocks MPC972 0' 0' 0' 0' 1' 0' 0' 0' 0' 1' 66 MHz fsela0 fsela1 fselb0 fselb1 fselc0 fselc1 fselFB0 fselFB1 fselFB2 Inv_Clk Input Ref Ext_FB Qa Qb Qc Qc QFB 4 4 2 2 66 MHz 66 MHz 66 MHz 66 MHz 0' 1' 0' 1' 1' 1' 0' 0' 0' 0' fsela0 fsela1 fselb0 fselb1 fselc0 fselc1 fselFB0 fselFB1 fselFB2 Inv_Clk Input Ref MPC972 Qa Qb Qc QFB 4 4 4 33 MHz Shifted 90 33 MHz Shifted 90 33 MHz Shifted 90 66 MHz 66 MHz 66 MHz Ext_FB 33 MHz Shifted 90 Figure 9. Phase Delay Using Multiple MPC972's 8 MOTOROLA MPC972 Using the On-Board Crystal Oscillator The MPC972 features an on-board crystal oscillator to allow for seed clock generation as well as final distribution. The on-board oscillator is completely self contained so that the only external component required is the crystal. As the oscillator is somewhat sensitive to loading on its inputs the user is advised to mount the crystal as close to the MPC972 as possible to avoid any board level parasitics. To facilitate co-location surface mount crystals are recommended, but not required. The oscillator circuit is a series resonant circuit as opposed to the more common parallel resonant circuit, this eliminates the need for large on-board capacitors. Because the design is a series resonant design for the optimum frequency accuracy a series resonant crystal should be used (see specification table below). Unfortunately most of the shelf crystals are characterized in a parallel resonant mode. However a parallel resonant crystal is physically no different than a series resonant crystal, a parallel resonant crystal is simply a crystal which has been characterized in its parallel resonant mode. Therefore in the majority of cases a parallel specified crystal can be used with the MPC972 with just a minor frequency error due to the actual series resonant frequency of the parallel resonant specified crystal. Typically a parallel specified crystal used in a series resonant mode will exhibit an oscillatory frequency a few hundred ppm lower than the specified value. For most processor implementations a few hundred ppm translates into kHz inaccuracies, a level which does not represent a major issue. 3. Crystal Recommendations Parameter Crystal Cut Resonance Frequency Tolerance Frequency/Temperature Stability Operating Range Shunt Capacitance Equivalent Series Resistance (ESR) Correlation Drive Level Aging Value Fundamental AT Cut Series Resonance* 75 ppm at 25C 150 pm 0 to 70C 0 to 70C 5-7 pF 50 to 80 Max 100 W 5 ppm/Yr (First 3 Years) RS=5-10 VCCA MPC972 VCC 0.01 F 0.01 F 22 F Recommended External Reset Timing For MPC972 applications requiring synchronization of the output clock to the input clock and if fselFB2 = 1, the assertion of MR is recommended. The timing of asserting MR should be as shown in 1. The power supply should be at or above the minimum specified voltage and the reference clock input (refclk) should be present a minimum of t1 prior to the reset pulse being applied to the MR pin. VDD -5% VDD Power MR refclk t1 t1 > 10 msec 10 ns < t2 < 20 ns t2 Figure 1. Assertion of MR Power Supply Filtering The MPC972 is a mixed analog/digital product and exhibits some sensitivities that would not necessarily be seen on a fully digital product. Analog circuitry is naturally susceptible to random noise, especially if this noise is seen on the power supply pins. The MPC972 provides separate power supplies for the output buffers (VCCO) and the internal PLL (VCCA) of the device. The purpose of this design technique is to try and isolate the high switching noise digital outputs from the relatively sensitive internal analog phase-locked loop. In a controlled environment such as an evaluation board this level of isolation is sufficient. However, in a digital system environment where it is more difficult to minimize noise on the power supplies a second level of isolation may be required. The simplest form of isolation is a power supply filter on the VCCA pin for the MPC972. 3.3 V * See accompanying text for series versus parallel resonant discussion. The MPC972 is a clock driver which was designed to generate outputs with programmable frequency relationships and not a synthesizer with a fixed input frequency. As a result the crystal input frequency is a function of the desired output frequency. For a design which utilizes the external feedback to the PLL the selection of the crystal frequency is straight forward; simply chose a crystal which is equal in frequency to the fed back signal. Figure 10. Power Supply Filter Figure 10 illustrates a typical power supply filter scheme. The MPC972 is most susceptible to noise with spectral content in the 1 KHz to 1 MHz range. Therefore the filter should be designed to target this range. The key parameter that needs to be met in the final filter design is the DC voltage drop that will be seen between the VCC supply and the VCCA pin of the MOTOROLA 9 MPC972 MPC972. From the data sheet the IVCCA current (the current sourced through the VCCA pin) is typically 15 mA (20 mA maximum), assuming that a minimum of 2.935 V must be maintained on the VCCA pin very little DC voltage drop can be tolerated when a 3.3 V VCC supply is used. The resistor shown in Figure 10 must have a resistance of 5-10 to meet the voltage drop criteria. The RC filter pictured will provide a broadband filter with approximately 100:1 attenuation for noise whose spectral content is above 20 KHz. As the noise frequency crosses the series resonant point of an individual capacitor it's overall impedance begins to look inductive and thus increases with increasing frequency. The parallel capacitor combination shown ensures that a low impedance path to ground exists for frequencies well above the bandwidth of the PLL. Although the MPC972 has several design features to minimize the susceptibility to power supply noise (isolated power and grounds and fully differential PLL) there still may be applications in which overall performance is being degraded due to system power supply noise. The power supply filter schemes discussed in this section should be adequate to eliminate power supply noise related problems in most designs. Driving Transmission Lines The MPC972 clock driver was designed to drive high speed signals in a terminated transmission line environment. To provide the optimum flexibility to the user the output drivers were designed to exhibit the lowest impedance possible. With an output impedance of approximately 10 the drivers can drive either parallel or series terminated transmission lines. For more information on transmission lines the reader is referred to application note AN1091 in the Timing Solutions data book (DL207/D). In most high performance clock networks point-to-point distribution of signals is the method of choice. In a point-to-point scheme either series terminated or parallel terminated transmission lines can be used. The parallel technique terminates the signal at the end of the line with a 50 resistance to VCC/2. This technique draws a fairly high level of DC current and thus only a single terminated line can be driven by each output of the MPC972 clock driver. For the series terminated case however there is no DC current draw, thus the outputs can drive multiple series terminated lines. Figure 11 illustrates an output driving a single series terminated line vs two series terminated lines in parallel. When taken to its extreme the fanout of the MPC972 clock driver is effectively doubled due to its capability to drive multiple lines. MPC972 OUTPUT BUFFER IN 7 RS = 43 ZO = 50 OutA MPC972 OUTPUT BUFFER IN 7 RS = 43 ZO = 50 OutB0 ZO = 50 OutB1 RS = 43 Figure 11. Single versus Dual Transmission Lines The waveform plots of Figure 12 show the simulation results of an output driving a single line vs two lines. In both cases the drive capability of the MPC972 output buffers is more than sufficient to drive 50 transmission lines on the incident edge. Note from the delay measurements in the simulations a delta of only 43 ps exists between the two differently loaded outputs. This suggests that the dual line driving need not be used exclusively to maintain the tight output-to-output skew of the MPC972. The output waveform in Figure 12 shows a step in the waveform, this step is caused by the impedance mismatch seen looking into the driver. The parallel combination of the 43 series resistor plus the output impedance does not match the parallel combination of the line impedances. The voltage wave launched down the two lines will equal: VL = VS ( Zo / Rs + Ro +Zo) = 3.0 (25/53.5) = 1.40 V At the load end the voltage will double, due to the near unity reflection coefficient, to 2.8 V. It will then increment towards the quiescent 3.0 V in steps separated by one round trip delay (in this case 4.0 ns). Since this step is well above the threshold region it will not cause any false clock triggering, however designers may be uncomfortable with unwanted reflections on the line. To better match the impedances when driving multiple lines the situation in Figure 13 should be used. In this case the series terminating resistors are reduced such that when the parallel combination is added to the output buffer impedance the line impedance is perfectly matched. 10 MOTOROLA MPC972 3.0 2.5 2.0 1.5 1.0 0.5 0 2 4 6 8 TIME (nS) 10 12 14 OutA tD = 3.8956 OutB tD = 3.9386 In Figure 12. Single versus Dual Waveforms MPC972 OUTPUT BUFFER 7 RS = 36 ZO = 50 RS = 36 ZO = 50 7 + 36 k 36 = 50 k 50 25 = 25 Figure 13. Optimized Dual Line Termination SPICE level output buffer models are available for engineers who want to simulate their specific interconnect schemes. In addition IV characteristics are in the process of being generated to support the other board level simulators in general use. Using the Output Freeze Circuitry With the recent advent of a "green" classification for computers the desire for unique power management among system designers is keen. The individual output enable control of the MPC972 allows designers, under software control, to implement unique power management schemes into their designs. Although useful, individual output control at the expense of one pin per output is too high, therefore a simple serial interface was derived to economize on the control pins. The freeze control logic provides a mechanism through which the MPC972 clock outputs may be frozen (stopped in the logic `0' state): The freeze mechanism allows serial loading of the 12-bit Serial Input Register, this register contains one programmable freeze enable bit for 12 of the 14 output clocks. The Qc0 and QFB outputs cannot be frozen with the serial port, this avoids any potential lock up situation should an error occur in the loading of the Serial Input Register. The user may program an output clock to freeze by writing logic `0' to the respective freeze enable bit. Likewise, the user may programmably unfreeze an output clock by writing logic `1' to the respective enable bit. The freeze logic will never force a newly-frozen clock to a logic `0' state before the time at which it would normally transition there. The logic simply keeps the frozen clock at logic `0' once it is there. Likewise, the freeze logic will never force a newly-unfrozen clock to a logic `1' state before the time at which it would normally transition there. The logic re-enables the unfrozen clock during the time when the respective clock would normally be in a logic `0' state, eliminating the possibility of `runt' clock pulses. The user may write to the Serial Input register through the Frz_Data input by supplying a logic `0' start bit followed serially by 12 NRZ freeze enable bits. The period of each Frz_Data bit equals the period of the free-running Frz_Clk signal. The Frz_Data serial transmission should be timed so the MPC972 can sample each Frz_Data bit with the rising edge of the free-running Frz_Clk signal. Start Bit D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 VOLTAGE (V) D0-D3 are the control bits for Qa0-Qa3, respectively D4-D7 are the control bits for Qb0-Qb3, respectively D8-D10 are the control bits for Qc1-Qc3, respectively D11 is the control bit for QSync Figure 14. Freeze Data Input Protocol MOTOROLA 11 MPC972 OUTLINE DIMENSIONS FA SUFFIX LQFP PACKAGE CASE 848D-03 ISSUE D 4X 4X 13 TIPS -X- X=L, M, N C L AB AB G 0.20 (0.008) H L-M N 0.20 (0.008) T L-M N 52 1 40 39 PLATING 3X VIEW Y F BASE METAL VIEW Y J B V B1 13 14 26 27 V1 0.13 (0.005) ROTATED 90_ CLOCKWISE NOTES: 1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION: MILLIMETER. 3 DATUM PLANE -H- IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4 DATUMS -L-, -M- AND -N- TO BE DETERMINED AT DATUM PLANE -H-. 5 DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE -T-. 6 DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 (0.010) PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE H . 7 DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. DAMBAR PROTRUSION SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED 0.46 (0.018). MINIMUM SPACE BETWEEN PROTRUSION AND ADJACENT LEAD OR PROTRUSION 0.07 (0.003). DIM A A1 B B1 C C1 C2 D E F G J K R1 S S1 U V V1 W Z 1 2 3 MILLIMETERS MIN MAX 10.00 BSC 5.00 BSC 10.00 BSC 5.00 BSC --1.70 0.05 0.20 1.30 1.50 0.20 0.40 0.45 0.75 0.22 0.35 0.65 BSC 0.07 0.20 0.50 REF 0.08 0.20 12.00 BSC 6.00 BSC 0.09 0.16 12.00 BSC 6.00 BSC 0.20 REF 1.00 REF 0_ 7_ --0_ 12 _ REF 12 _ REF INCHES MIN MAX 0.394 BSC 0.197 BSC 0.394 BSC 0.197 BSC --0.067 0.002 0.008 0.051 0.059 0.008 0.016 0.018 0.030 0.009 0.014 0.026 BSC 0.003 0.008 0.020 REF 0.003 0.008 0.472 BSC 0.236 BSC 0.004 0.006 0.472 BSC 0.236 BSC 0.008 REF 0.039 REF 0_ 7_ --0_ 12 _ REF 12 _ REF A1 S1 A S -N- C -H- -T- SEATING PLANE 4X q2 0.10 (0.004) T 4X q3 VIEW AA 0.05 (0.002) S W q1 C2 q 2X R R1 0.25 (0.010) GAGE PLANE K C1 E VIEW AA Z 12 C EE E CCCE ECCE EE M -L- -M- U D T L-M S N S SECTION AB-AB MOTOROLA MPC972 NOTES MOTOROLA 13 MPC972 NOTES 14 MOTOROLA MPC972 NOTES MOTOROLA 15 MPC972 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. E Motorola, Inc. 2001. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or 1-800-441-2447 JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3-20-1, Minami-Azabu. Minato-ku, Tokyo 106-8573 Japan. 81-3-3440-3569 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. 852-26668334 Technical Information Center: 1-800-521-6274 HOME PAGE: http://www.motorola.com/semiconductors/ 16 MPC972/D MOTOROLA |
Price & Availability of MPC972
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |