 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| August 1995 Edition 6.0b DATA SHEET MB501L/504/504L TWO MODULUS PRESCALERS TWO MODULUS PRESCALERS The Fujitsu MB501L/504/504L are two modulus prescalers, which are use with a frequency synthesizer to make a PLL (Phase Locked Loop). They will divide the input frequency by the modulus of 64/65 or 128/129 for the MB501L, and 32/33 or 64/65 for the MB504/MB504L. The MB501L and MB504L are low-power versions. The output of 1.6V peak to peak on ECL level applies to all. S High Operating Frequency, Low Power Operation: 1.1GHz at 50mW typ. (MB501L) 520MHz at 50mW typ. (MB504) 520MHz at 25mW typ. (MB504L) S Pulse Swallow Function S Wide Operation Temperature S Stable Output Amplitude: TA = -40C to +85C VOUT = 1.6Vp-p PLASTIC PACKAGE DIP-08P-M01 S Complete PLL synthesizer circuit with the Fujitsu MB87001A, PLL synthesizer IC S Plastic 8-pin Standard Dual-In-Line Package or space saving Flat Package PLASTIC PACKAGE FPT-08P-M01 ABSOLUTE MAXIMUM RATINGS (see NOTE) Rating Supply Voltage Input Voltage Output Current Ambient Temperature Storage Temperature Symbol VCC VIN VO TA TSTG Value -0.5 to +7.0 -0.5 to VCC 10 -40 to +85 - 55 to +125 Unit V V mA _C _C IN VCC SW OUT 1 2 TOP VIEW 3 4 6 5 MC GND 8 7 IN NC PIN ASSIGNMENT Note: Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation should be restricted to the conditions as detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields. However, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high impedance circuit. Copyright E 1990 by FUJITSU LIMITED MB501L MB504 MB504L a) MB501L DQ Input Buffer IN IN C DQ C SW DQ CM SW H MB501/ MB501L OUT MC H L H L Divide Ratio 1/64 1/65 1/128 1/129 DQ CQ DQ CQ DQ CQ DQ CQ DQ SW CQ Output Buffer H L L Note: SW: H = VCC, L = OPEN MC: H = 2.0V to VCC, L = GND to 0.8V MC b) MB504/MB504L DQ Input Buffer IN IN C DQ C SW DQ CM SW H MB504/ MB504L OUT MC H L H L Divide Ratio 1/32 1/33 1/64 1/65 DQ CQ DQ CQ DQ CQ DQ SW CQ Output Buffer H L L Note: SW: H = VCC, L = OPEN MC: H = 2.0V to VCC, L = GND to 0.8V MC Figure 1. Block Diagrams 2 MB501L MB504 MB504L PIN DESCRIPTION Pin Number 1 2 3 4 5 6 7 8 Symbol IN VCC SW OUT GND MC NC IN Input DC Supply Voltage Divide Ratio Control Input (See Divide Ratio Table) Output Ground Modulus Control Input (See Divide Ratio Table) Non Connection Complementary Input Function RECOMMENDED OPERATING CONDITIONS Value Parameter Symbol Min. Supply Voltage Output Current Ambient Temperature Load Capacitance VCC IO TA CL -40 4.5 Typ. 5.0 1.2 +85 12 Max. 5.5 V mA C pF Unit 3 MB501L MB504 MB504L ELECTRICAL CHARACTERISTICS (Recommended Operating Conditions unless otherwise noted) Value Parameter MB501L Power Supply Current MB504 MB504L Output Amplitude MB501L Input Frequency MB504 MB504L MB501L Input Signal Amplitude for IN MB504 MB504L High Level Input Voltage for MC Low Level Input Voltage for MC High Level Input Voltage for SW Low Level Input Voltage for SW High Level Input Current for MC Low Level Input Current for MC MB501L Modulus Set-up Time MC to OUT MB504 MB504L Note: * VCC = 5V, TA = 25C ** Design Guarantee tSET VIHM VILM VIHS** VILS IIHM IILM VIH = 2.0V VIL = 0.8V -0.2 16 20 18 26 30 28 VCC -0.1 VCC OPEN 0.4 PIN fIN With input coupling capacitor 1000pF VO 1.0 10 10 10 -4 -12 -12 2.0 0.8 VCC +0.1 ICC I/O pins are open Symbol Conditions Min. Typ. 10 10 5 1.6 1100 520 520 5.5 10 10 Max. 14* 14* 7* mA mA mA VP-P MHz MHz MHz dBm dBm dBm V V V V mA mA ns ns ns Unit 4 MB501L MB504 MB504L MB501L TIMING CHART (2 MODULUS) Example: Divide Ratio of 64/65 64 65 IN 32 32 32 33 OUT 32 32 32 32 32 32 33 32 33 32 32 MC tSET tSET Note: When divide ratio of 65 is selected, positive pulse is applied by one to 33. The typical set up time is 16ns (MB501L) from the MC signal input to the timing of change of prescaler divide ratio. 5 MB501L MB504 MB504L MB504/MB504L TIMING CHART (2 MODULUS) Example: Divide Ratio of 32/33 32 33 IN 16 16 16 17 OUT 16 16 16 16 16 16 17 16 17 16 16 MC tSET tSET Note: When divide ratio of 33 is selected, positive pulse is applied by one to 17. The typical set up time is 20ns (MB504), 18ns (MB504L) from the MC signal input to the timing of change of prescaler divide ratio. 6 MB501L MB504 MB504L VCC = +5.0V + 10% C3 Sampling scope input point for input waveform C1 P.G. IN VCC SW OUT Sampling scope prober point for output waveform IN 50 C2 CL MC GND RL MC Input C1: 1000pF C2: 1000pF C3: 0.1F CL: 12pF (including scope and jig capacitance) RL: 2k Figure 2. Test Circuit 7 MB501L MB504 MB504L TYPICAL CHARACTERISTICS CURVES MINIMUM INPUT SIGNAL AMPLITUDE (mV) 1000 MB501L 800 VCC = 5.0V TA = 25C 600 400 200 0 10 20 50 100 200 500 1000 2000 INPUT FREQUENCY (MHz) Figure 3. Input Signal Amplitude vs. Input Frequency MINIMUM INPUT SIGNAL AMPLITUDE (mV) 1000 MB504 800 VCC = 5.0V TA = 25C 600 400 200 0 10 20 50 100 200 500 1000 INPUT FREQUENCY (MHz) Figure 4. Input Signal Amplitude vs. Input Frequency 8 MB501L MB504 MB504L TYPICAL CHARACTERISTICS CURVES (Continued) MINIMUM INPUT SIGNAL AMPLITUDE (mV) 1000 MB504L 800 VCC = 5.0V TA = 25C 600 400 200 0 10 20 50 100 200 500 1000 INPUT FREQUENCY (MHz) Figure 5. Input Signal Amplitude vs. Input Frequency 9 MB501L MB504 MB504L C1 VCC C2 XI 12K VSX (Max. 8V) VCC VCC 10K 16 15 14 13 12 11 10 9 MB87001A 0.047F 12K VCO OUTPUT 12 3 4 56 78 100K 10K 33K Clock Data LE 1000pF 1000pF 47K 47K 47K 87 VCC 6 5 PRESCALER 12 3 4 XI VCC VSX C1, C2 :12.8MHz x'tal : +2.75V to +4.5V : 8V Max. : depends on crystal oscillator 1000pF 1000pF 2.2K Lock Det. 10K An example of application of MB501L/504/504L with PLL Synthesizer IC MB87001A Figure 6. Typical Application Example 10 MB501L MB504 MB504L PACKAGE DIMENSIONS 8-LEAD PLASTIC DUAL IN-LINE PACKAGE (CASE No.: DIP-08P-M01) ) .016 .370 -.012 ) 0.40 9.40 -0.30 15C MAX. INDEX .244 .010 (6.20 0.25) .300 (7.62) TYP. ) .012 .039 -.000 ) 0.30 0.99 -0.00 ) .012 .060 -.000 ) 0.30 1.52 -0.00 .010 .002 (0.25 0.05) ) .014 .035 -.012 ) 0.35 0.89 -0.30 .172 (4.36) MAX. .020 (0.51) MIN. .100 (2.54) TYP. .018 .003 (0.46 0.08) .118 (3.00) MIN. Dimensions in inches (millimeters). E1988 FUJITSU LIMITED D08006S-2C 11 MB501L MB504 MB504L PACKAGE DIMENSIONS (Continued) 8-LEAD PLASTIC FLAT PACKAGE (CASE No.: FPT-08P-M01) ) .010 .250 - .008 ) 0.25 6.35 - 0.20 .089(2.25) MAX. (SEATED HEIGHT) .002(0.05) MIN. (STAND OFF) .307+.016 (7.80+0.40) INDEX .209+.012 (5.30+0.30) ) .016 .268 - .008 ) 0.40 6.80 - 0.20 .020+.008 (0.50+0.20) .050(1.27) TYP. .150(3.81) REF. "A" Details of "A" part .008(0.20) .018+.004 (0.45+0.10) .005(0.13) M ) .002 .006 - .001 ) 0.05 0.15 - 0.02 .004(0.10) .020(0.50) .007(0.18) MAX. .027(0.68) MAX. Dimensions in inches (millimeters). E1988 FUJITSU LIMITED F08002S-3C 12 MB501L MB504 MB504L All Rights Reserved. Circuit diagrams utilizing Fujitsu products are included as a means of illustrating typical semiconductor applications. Complete information sufficient for construction purposes is not necessarily given. The information contained in this document has been carefully checked and is believed to be reliable. However, Fujitsu assumes no responsibility for inaccuracies. The information contained in this document does not convey any license under the copyrights, patent rights or trademarks claimed and owned by Fujitsu. Fujitsu reserves the right to change products or specifications without notice. No part of this publication may be copied or reproduced in any form or by any means, or transferred to any third party without prior written consent of Fujitsu. 14 MB501L MB504 MB504L FUJITSU LIMITED For further information please contact: Japan FUJITSU LIMITED International Marketing Div. Furukawa Sogo Bldg., 6-1, Marunouchi 2-chome Chiyoda-ku, Tokyo 100, Japan Tel: (03) 3216-3211 Telex: 781-2224361 FAX: (03) 3215-0662 North and South America FUJITSU MICROELECTRONICS, INC. Integrated Circuits Division 3545 North First Street San Jose, CA 95134-1804, USA Tel: 408-922-9000 FAX: 408-432-9044 Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10, 6072 Dreieich-Buchschlag, Germany Tel: (06103) 690-0 Telex: 411963 FAX: (06103) 690-122 Asia FUJITSU MICROELECTRONICS ASIA PTE LIMITED 51 Bras Basah Road, Plaza By The Park, #06-04 to #06-07 Singapore 0719 Tel: 336-1600 Telex: 55573 FAX: 336-1609 (c)FUJITSU LIMITED 1990 Printed in Japan PV0037-904A6 15 |
Price & Availability of MB501
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |