|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
HUF76131SK8 Data Sheet January 2003 10A, 30V, 0.013 Ohm, N-Channel, Logic Level UltraFET Power MOSFET This N-Channel power MOSFET is (R) manufactured using the innovative UltraFET process. This advanced process technology achieves the lowest possible on-resistance per silicon area, resulting in outstanding performance. This device is capable of withstanding high energy in the avalanche mode and the diode exhibits very low reverse recovery time and stored charge. It was designed for use in applications where power efficiency is important, such as switching regulators, switching converters, motor drivers, relay drivers, lowvoltage bus switches, and power management in portable and battery-operated products. Formerly developmental type TA76131. Features * Logic Level Gate Drive * 10A, 30V * Ultra Low On-Resistance, rDS(ON) = 0.013 * Temperature Compensating PSPICE(R) Model * Thermal Impedance SPICE Model * Peak Current vs Pulse Width Curve * UIS Rating Curve * Related Literature - TB334, "Guidelines for Soldering Surface Mount Components to PC Boards" Symbol SOURCE(1) DRAIN(8) Ordering Information PART NUMBER HUF76131SK8 PACKAGE MS-012AA BRAND 76131SK8 SOURCE(2) DRAIN(7) NOTE: When ordering, use the entire part number. Add the suffix T to obtain the variant in tape and reel, e.g., HUF76131SK8T. SOURCE(3) DRAIN(6) GATE(4) DRAIN(5) Packaging JEDEC MS-012AA BRANDING DASH 5 1 2 3 4 (c)2003 Fairchild Semiconductor Corporation HUF76131SK8 Rev. B1 HUF76131SK8 Absolute Maximum Ratings TA = 25oC, Unless Otherwise Specified HUF76131SK8 30 30 20 10 Figure 5 Figure 6 2.5 0.02 -55 to 150 300 260 UNITS V V V A Drain to Source Voltage (Note 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDSS Drain to Gate Voltage (R GS = 20k) (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VDGR Gate to Source Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGS Drain Current Continuous (Figure 2) (Notes 2, 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ID Pulsed Drain Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IDM Pulsed Avalanche Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EAS Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PD Derate Above 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating and Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG Maximum Temperature for Soldering Leads at 0.063in (1.6mm) from Case for 10s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL Package Body for 10s, See Techbrief 334. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tpkg W W/oC oC oC oC CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. TJ = 25oC to 150oC. Electrical Specifications PARAMETER TA = 25oC, Unless Otherwise Specified SYMBOL BVDSS VGS(TH) IDSS IGSS rDS(ON) TEST CONDITIONS ID = 250A, V GS = 0V (Figure 11) VGS = VDS, ID = 250A (Figure 10) VDS = 25V, VGS = 0V VDS = 25V, VGS = 0V, TA = 150oC VGS = 20V ID = 10A, VGS = 4.5V (Figures 9,14) ID = 10A, VGS = 5V ID = 10A, VGS = 10V MIN 30 1 VGS = 0V to 10V VDD = 15V, ID 10A, VGS = 0V to 5V RL = 1.5, Ig(REF) = 1.0mA (Figure 13) VGS = 0V to 1V VDS = 25V, VGS = 0V, f = 1MHz (Figure 12) Pad Area = 0.76 in2 (Note 2) Pad Area = 0.054 in2 (See TB377) Pad Area = 0.0115 in2 (See TB377) TYP 0.017 0.015 0.011 15 61 33 36 39 22 1.53 4.00 9.50 1605 685 115 MAX 1 250 100 0.018 0.017 0.013 115 105 47 26 1.85 50 143.4 177.3 UNITS V V A A nA ns ns ns ns ns ns nC nC nC nC nC pF pF pF oC/W oC/W oC/W Drain to Source Breakdown Voltage Gate to Source Threshold Voltage Zero Gate Voltage Drain Current Gate to Source Leakage Current Drain to Source On Resistance Turn-On Time Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Turn-Off Time Total Gate Charge Gate Charge at 5V Threshold Gate Charge Gate to Source Gate Charge Gate to Drain "Miller" Charge Input Capacitance Output Capacitance Reverse Transfer Capacitance Thermal Resistance Junction to Ambient tON td(ON) tr td(OFF) tf tOFF Qg(TOT) Qg(5) Qg(TH) Qgs Qgd CISS COSS CRSS RJA VDD = 15V, ID 10A, R L = 1.5, VGS = 5V, RGS = 6.8 (Figure 15) Source to Drain Diode Specifications PARAMETER Source to Drain Diode Voltage Reverse Recovery Time Reverse Recovered Charge NOTES: 2. 50oC/W measured using FR-4 board with 0.76 in2 footprint at 10 seconds. 3. 177.3oC/W measured using FR-4 board with 0.0115 in2 footprint at 1000 seconds. (c)2003 Fairchild Semiconductor Corporation HUF76131SK8 Rev. B1 SYMBOL VSD trr QRR ISD = 10A ISD = 2.3A TEST CONDITIONS MIN - TYP - MAX 1.25 1.1 57 81 UNITS V V ns nC ISD = 2.3A, dISD/dt = 100A/s ISD = 2.3A, dISD/dt = 100A/s HUF76131SK8 Typical Performance Curves 1.2 POWER DISSIPATION MULTIPLIER 1.0 0.8 0.6 0.4 0.2 0 0 25 50 75 100 125 150 TA , AMBIENT TEMPERATURE (oC) ID, DRAIN CURRENT (A) 12 10 8 6 4 2 0 25 50 75 100 125 150 TA, AMBIENT TEMPERATURE (oC) FIGURE 1. NORMALIZED POWER DISSIPATION vs AMBIENT TEMPERATURE FIGURE 2. MAXIMUM CONTINUOUS DRAIN CURRENT vs AMBIENT TEMPERATURE 10 THERMAL IMPEDANCE ZJA, NORMALIZED 1 DUTY CYCLE - DESCENDING ORDER 0.5 0.2 0.1 0.05 0.02 0.01 PDM 0.1 t1 0.01 t2 NOTES: DUTY FACTOR: D = t1/t2 PEAK TJ = PDM x ZJA x RJA + TA 10-2 10-1 100 101 102 10 3 SINGLE PULSE 0.001 10 -5 10-4 10 -3 t, RECTANGULAR PULSE DURATION (s) FIGURE 3. NORMALIZED MAXIMUM TRANSIENT THERMAL IMPEDANCE 500 TJ = MAX RATED TA = 25oC 1000 TRANSCONDUCTANCE MAY LIMIT CURRENT IN THIS REGION 100 100s IDM, PEAK CURRENT (A) ID, DRAIN CURRENT (A) 100 VGS = 5V 10 OPERATION IN THIS AREA MAY BE LIMITED BY rDS(ON) 1ms 10 FOR TEMPERATURES ABOVE 25oC DERATE PEAK CURRENT AS FOLLOWS: I = I 25 150 - TA 125 TA = 25oC 10-1 t, PULSE WIDTH (s) 10-2 100 10 1 10ms VDSS(MAX) = 30V 1 1 10 VDS , DRAIN TO SOURCE VOLTAGE (V) 100 1 10-5 10 -4 10 -3 FIGURE 4. FORWARD BIAS SAFE OPERATING AREA FIGURE 5. PEAK CURRENT CAPABILITY (c)2003 Fairchild Semiconductor Corporation HUF76131SK8 Rev. B1 HUF76131SK8 Typical Performance Curves 100 IAS, AVALANCHE CURRENT (A) If R = 0 tAV = (L)(IAS)/(1.3*RATED BVDSS - VDD) If R 0 tAV = (L/R)ln[(IAS*R)/(1.3*RATED BVDSS - VDD) +1] I D, DRAIN CURRENT (A) (Continued) 50 VGS = 10V VGS = 5V VGS = 4.5V VGS = 4V VGS = 3.5V 40 10 STARTING TJ = 150oC STARTING TJ = 25 oC 30 20 VGS = 3V 10 1 0.1 1 10 100 0 0 PULSE DURATION = 80s DUTY CYCLE = 0.5% MAX TA = 25oC 0.5 1.0 1.5 2.0 VDS, DRAIN TO SOURCE VOLTAGE (V) 2.5 tAV, TIME IN AVALANCHE (ms) NOTE: Refer to Fairchild Application Notes AN9321 and AN9322. FIGURE 6. UNCLAMPED INDUCTIVE SWITCHING CAPABILITY 50 NORMALIZED DRAIN TO SOURCE ON RESISTANCE PULSE DURATION = 80s DUTY CYCLE = 0.5% MAX ID, DRAIN CURRENT (A) 40 FIGURE 7. SATURATION CHARACTERISTICS 1.75 PULSE DURATION = 80s DUTY CYCLE = 0.5% MAX VGS = 10V, ID = 10A 1.5 30 1.25 20 1.0 10 150 oC 25 oC -55oC VDD = 15V 3.5 4.0 0 0 0.5 2.0 2.5 3.0 1.0 1.5 VGS, GATE TO SOURCE VOLTAGE (V) 0.75 -80 -40 0 40 80 120 160 TJ, JUNCTION TEMPERATURE (oC) FIGURE 8. TRANSFER CHARACTERISTICS FIGURE 9. NORMALIZED DRAIN TO SOURCE ON RESISTANCE vs JUNCTION TEMPERATURE 1.2 VGS = VDS , ID = 250A NORMALIZED DRAIN TO SOURCE BREAKDOWN VOLTAGE 1.2 ID = 250A NORMALIZED GATE THRESHOLD VOLTAGE 1.0 1.1 0.8 1.0 0.6 0.9 0.4 -80 -40 0 40 80 120 TJ, JUNCTION TEMPERATURE (oC) 160 0.8 -80 -40 0 40 80 120 TJ , JUNCTION TEMPERATURE (oC) 160 FIGURE 10. NORMALIZED GATE THRESHOLD VOLTAGE vs JUNCTION TEMPERATURE FIGURE 11. NORMALIZED DRAIN TO SOURCE BREAKDOWN VOLTAGE vs JUNCTION TEMPERATURE (c)2003 Fairchild Semiconductor Corporation HUF76131SK8 Rev. B1 HUF76131SK8 Typical Performance Curves 2500 VGS , GATE TO SOURCE VOLTAGE (V) VGS = 0V, f = 1MHz CISS = CGS + C GD CRSS = CGD COSS = C DS + CGD (Continued) 10 2000 C, CAPACITANCE (pF) CISS 1500 8 6 1000 COSS 500 CRSS 0 0 5 10 15 20 25 VDS , DRAIN TO SOURCE VOLTAGE (V) 30 4 2 VDD = 15V 0 0 10 WAVEFORMS IN DESCENDING ORDER: ID = 20A ID = 10A ID = 5A ID = 2.5A 40 50 20 30 Qg, GATE CHARGE (nC) NOTE: Refer to Fairchild Application Notes 7254 and 7260. FIGURE 12. CAPACITANCE vs DRAIN TO SOURCE VOLTAGE FIGURE 13. GATE CHARGE WAVEFORMS FOR CONSTANT GATE CURRENT 80 rDS(ON), ON-STATE RESISTANCE (m) 200 VDD = 15V, I D = 10A, RL= 1.5 60 ID = 5A SWITCHING TIME (ns) ID = 10A ID = 20A 150 tr td(OFF) 100 tf 40 ID = 2.5A 20 PULSE DURATION = 80s DUTY CYCLE = 0.5% MAX 0 0 2 6 8 4 VGS, GATE TO SOURCE VOLTAGE (V) 10 50 td(ON) 0 0 10 20 30 40 RGS, GATE TO SOURCE RESISTANCE () 50 FIGURE 14. DRAIN TO SOURCE ON RESISTANCE vs GATE VOLTAGE AND DRAIN CURRENT FIGURE 15. SWITCHING TIME vs GATE RESISTANCE Test Circuits and Waveforms VDS BVDSS L VARY tP TO OBTAIN REQUIRED PEAK IAS VGS DUT tP RG IAS VDD tP VDS VDD + 0V IAS 0.01 0 tAV FIGURE 16. UNCLAMPED ENERGY TEST CIRCUIT FIGURE 17. UNCLAMPED ENERGY WAVEFORMS (c)2003 Fairchild Semiconductor Corporation HUF76131SK8 Rev. B1 HUF76131SK8 Test Circuits and Waveforms VDS (Continued) tON td(ON) RL VDS + tOFF td(OFF) tr tf 90% 90% VGS DUT RGS VDD 0 10% 90% 10% VGS VGS 0 10% 50% PULSE WIDTH 50% FIGURE 18. SWITCHING TIME TEST CIRCUIT VDS RL VDD FIGURE 19. SWITCHING TIME WAVEFORM Qg(TOT) VDS VGS = 10V VGS + Qg(5) VDD VGS VGS = 1V 0 Qg(TH) Ig(REF) 0 VGS = 5V DUT Ig(REF) FIGURE 20. GATE CHARGE TEST CIRCUIT FIGURE 21. GATE CHARGE WAVEFORMS (c)2003 Fairchild Semiconductor Corporation HUF76131SK8 Rev. B1 HUF76131SK8 Thermal Resistance vs Mounting Pad Area The maximum rated junction temperature TJMAX constrains the maximum allowable device power dissipation P Dmax in an application. The application ambient temperature TA (oC) and thermal impedance ZJA (oC/W) must be reviewed to ensure that TJMAX (oC) is never exceeded. Equation 1 mathematically represents the relationship. (T -T ) JMAX A P DMAX = --------------------------------------Z JA Thermal resistance values corresponding to other component side copper areas can be obtained from Figure 22 or by calculation using Equation 2. Area in Equation 2 is the top copper area including the gate and source pads. R JA = 79.3 - 21.8 x ln ( Area ) (EQ. 2) 250 (EQ. 1) 200 RJA (oC/W) RJA = 79.3 - 21.8*ln(AREA) Fairchild provides thermal information to assist the designer's preliminary application evaluation. Precise determination of PDMAX is complex and influenced by many factors: 1. PC heat sink area and location (top and bottom), copper leads and mounting pad area. 2. Air Flow, board orientation and type. 3. Power pulse width and duty factor. Figure 22 addresses these points by depicting RJA values vs. top copper (component side) heat sink area. The measurements were performed in still air using a horizontally positioned FR-4 board with 1oz copper after 1000 seconds of steady state power. Figure 22 also displays the two RJA values listed in the Electrical Specifications table. The two points were chosen to graphically depict the compromise between copper board area, thermal resistance and ultimately power dissipation. 177.3 oC/W - 0.0115in2 143.4oC/W - 0.054in2 150 100 50 0.001 0.01 0.1 AREA, TOP COPPER AREA (in2) 1.0 FIGURE 22. THERMAL RESISTANCE vs MOUNTING PAD AREA Figure 22 provides the necessary information for steady state junction temperature or power dissipation calculations. Transient pulse applications are best studied using the Fairchild device SPICE thermal model. (c)2003 Fairchild Semiconductor Corporation HUF76131SK8 Rev. B1 HUF76131SK8 PSPICE Electrical Model SUBCKT HUF76131 2 1 3 ; CA 12 8 2.22-9 CB 15 14 2.13e-9 CIN 6 8 1.52e-9 10 rev 12/31/97 LDRAIN DPLCAP 5 RLDRAIN DBREAK 11 + EBREAK MWEAK MMED MSTRO CIN LSOURCE 8 RSOURCE RLSOURCE S1A 12 S1B CA 13 + EGS 6 8 EDS 13 8 S2A 14 13 S2B CB + 5 8 14 IT 15 17 RBREAK 18 RVTEMP 19 7 SOURCE 3 17 18 DBODY DRAIN 2 RSLC1 51 ESLC 50 RSLC2 5 51 EBREAK 11 7 17 18 37.4 EDS 14 8 5 8 1 EGS 13 8 6 8 1 ESG 6 10 6 8 1 EVTHRES 6 21 19 8 1 EVTEMP 20 6 18 22 1 IT 8 17 1 LDRAIN 2 5 1e-9 LGATE 1 9 1.04e-9 LSOURCE 3 7 1.29e-10 MMED 16 6 8 8 MMEDMOD MSTRO 16 6 8 8 MSTROMOD MWEAK 16 21 8 8 MWEAKMOD RBREAK 17 18 RBREAKMOD 1 RDRAIN 50 16 RDRAINMOD 1.94e-3 RGATE 9 20 2.20 RLDRAIN 2 5 10 RLGATE 1 9 10.4 RLSOURCE 3 7 1.29 RSLC1 5 51 RSLCMOD 1e-6 RSLC2 5 50 1e3 RSOURCE 8 7 RSOURCEMOD 8.75e-3 RVTHRES 22 8 RVTHRESMOD 1 RVTEMP 18 19 RVTEMPMOD 1 S1A S1B S2A S2B 6 12 13 8 S1AMOD 13 12 13 8 S1BMOD 6 15 14 13 S2AMOD 13 15 14 13 S2BMOD GATE 1 ESG + LGATE EVTEMP RGATE + 18 22 9 20 6 8 EVTHRES + 19 8 6 RLGATE - - VBAT 22 19 DC 1 ESLC 51 50 VALUE={(V(5,51)/ABS(V(5,51)))*(PWR(V(5,51)/(1e-6*275),3))} .MODEL DBODYMOD D (IS = 2.25e-12 RS = 6.05e-3 IKF=16.00 TRS1 = 1.14e-4 TRS2 = 1.23e-6 CJO = 2.35e-9 TT = 2.71e-8 M = 0.44) .MODEL DBREAKMOD D (RS = 1.05e-1 TRS1 = 1.01e-4 TRS2 = 1.11e-7) .MODEL DPLCAPMOD D (CJO = 1.08e-9 IS = 1e-30 N = 10 M = 0.69) .MODEL MMEDMOD NMOS (VTO = 1.89 KP = 5.05 IS = 1e-30 N = 10 TOX = 1 L = 1u W = 1u RG = 2.20) .MODEL MSTROMOD NMOS (VTO = 2.22 KP = 125.00 IS = 1e-30 N = 10 TOX = 1 L = 1u W = 1u) .MODEL MWEAKMOD NMOS (VTO = 1.62 KP = 0.10 IS = 1e-30 N = 10 TOX = 1 L = 1u W = 1u RG = 22.0 RS = 0.1) .MODEL RBREAKMOD RES (TC1 = 9.54e-4 TC2 = 1.07e-7) .MODEL RDRAINMOD RES (TC1 = 1.61e-2 TC2 = 5.17e-5) .MODEL RSLCMOD RES (TC1 = 1.03e-5 TC2 = 7.67e-7) .MODEL RSOURCEMOD RES (TC1 = 0 TC2 = 0) .MODEL RVTHRESMOD RES (TC = -2.81e-3 TC2 = -8.75e-6) .MODEL RVTEMPMOD RES (TC1 = -6.68e-4 TC2 = 8.80e-7) .MODEL S1AMOD VSWITCH (RON = 1e-5 .MODEL S1BMOD VSWITCH (RON = 1e-5 .MODEL S2AMOD VSWITCH (RON = 1e-5 .MODEL S2BMOD VSWITCH (RON = 1e-5 .ENDS ROFF = 0.1 ROFF = 0.1 ROFF = 0.1 ROFF = 0.1 VON = -5.80 VOFF= -1.50) VON = -1.50 VOFF= -5.80) VON = -0.50 VOFF= -0.00) VON = 0.00 VOFF= -0.50) NOTE: For further discussion of the PSPICE model, consult A New PSPICE Sub-Circuit for the Power MOSFET Featuring Global Temperature Options; IEEE Power Electronics Specialist Conference Records, 1991, written by William J. Hepp and C. Frank Wheatley. (c)2003 Fairchild Semiconductor Corporation + DBODY 7 5 DBODYMOD DBREAK 5 11 DBREAKMOD DPLCAP 10 5 DPLCAPMOD - RDRAIN 21 16 - VBAT + 8 22 RVTHRES HUF76131SK8 Rev. B1 HUF76131SK8 SPICE Thermal Model REV 20 Feb 98 HUF76131 CTHERM1 7 6 3.75e-4 CTHERM2 6 5 3.05e-3 CTHERM3 5 4 3.70e-2 CTHERM4 4 3 2.52e-2 CTHERM5 3 2 8.50e-2 CTHERM6 2 1 7.95e-1 RTHERM1 7 6 3.95e-2 RTHERM2 6 5 2.50e-1 RTHERM3 5 4 4.00e-1 RTHERM4 4 3 6.35 RTHERM5 3 2 2.02e1 RTHERM6 2 1 4.80e1 RTHERM1 CTHERM1 7 JUNCTION 6 RTHERM2 CTHERM2 5 RTHERM3 CTHERM3 4 RTHERM4 CTHERM4 3 RTHERM5 CTHERM5 2 RTHERM6 CTHERM6 1 CASE (c)2003 Fairchild Semiconductor Corporation HUF76131SK8 Rev. B1 TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACExTM FACTTM ActiveArrayTM FACT Quiet SeriesTM BottomlessTM FAST(R) CoolFETTM FASTrTM CROSSVOLTTM FRFETTM DOMETM GlobalOptoisolatorTM EcoSPARKTM GTOTM E2CMOSTM HiSeCTM I2CTM EnSignaTM Across the board. Around the world.TM The Power FranchiseTM Programmable Active DroopTM DISCLAIMER ImpliedDisconnectTM ISOPLANARTM LittleFETTM MicroFETTM MicroPakTM MICROWIRETM MSXTM MSXProTM OCXTM OCXProTM OPTOLOGIC(R) OPTOPLANARTM PACMANTM POPTM Power247TM PowerTrench(R) QFETTM QSTM QT OptoelectronicsTM Quiet SeriesTM RapidConfigureTM RapidConnectTM SILENT SWITCHER(R) SMART STARTTM SPMTM StealthTM SuperSOTTM-3 SuperSOTTM-6 SuperSOTTM-8 SyncFETTM TinyLogic(R) TruTranslationTM UHCTM UltraFET(R) VCXTM FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Advance Information Product Status Formative or In Design First Production Definition This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Preliminary No Identification Needed Full Production Obsolete Not In Production Rev. I2 |
Price & Availability of HUF76131SK8 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |