Part Number Hot Search : 
PCA9632 RP7E1X1 KF17N50N 40N60 DT54F LT1324 KTLP168J MC33076P
Product Description
Full Text Search
 

To Download AD5680BRJZ-2500RL7 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 5 V 18-Bit nanoDACTM in a SOT-23 AD5680
FEATURES
Single 18-bit nanoDAC 18-bit monotonic 12-bit accuracy guaranteed Tiny 8-lead SOT-23 package Power-on reset to zero scale/midscale 4.5 V to 5.5 V power supply Serial interface Rail-to-rail operation SYNC interrupt facility Temperature range -40C to +105C
FUNCTIONAL BLOCK DIAGRAM
VREF GND VDD VFB
POWER-ON RESET OUTPUT BUFFER
DAC REGISTER
REF(+) 18-BIT DAC
VOUT
INPUT CONTROL LOGIC
Closed-loop process control Low bandwidth data acquisition systems Portable battery-powered instruments Gain and offset adjustment Precision setpoint control
SYNC
SCLK
DIN
Figure 1.
GENERAL DESCRIPTION
The AD5680, a member of the nanoDAC family, is a single, 18-bit buffered voltage-out DAC that operates from a single 4.5 V to 5.5 V supply and is 18-bit monotonic. The AD5680 requires an external reference voltage to set the output range of the DAC. The part incorporates a power-on reset circuit that ensures the DAC output powers up to 0 V (AD5680-1) or to midscale (AD5680-2) and remains there until a valid write takes place. The low power consumption of this part in normal operation makes it ideally suited to portable battery-operated equipment. The power consumption is 1.6 mW at 5 V. The AD5680 on-chip precision output amplifier allows rail-torail output swing to be achieved. For remote sensing applications, the output amplifier's inverting input is available to the user. The AD5680 uses a versatile 3-wire serial interface that operates at clock rates up to 30 MHz, and is compatible with standard SPI(R), QSPITM, MICROWIRETM, and DSP interface standards.
PRODUCT HIGHLIGHTS
1. 2. 3. 4. 5. 18 bits of resolution. 12-bit accuracy guaranteed for 18-bit DAC. Available in an 8-lead SOT-23. Low power. Typically consumes 1.6 mW at 5 V. Power-on reset to zero scale or to midscale.
RELATED DEVICES
AD5662 16-bit DAC in SOT-23.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2006 Analog Devices, Inc. All rights reserved.
05854-001
APPLICATIONS
AD5680
AD5680 TABLE OF CONTENTS
Features .............................................................................................. 1 Applications....................................................................................... 1 Functional Block Diagram .............................................................. 1 General Description ......................................................................... 1 Product Highlights ........................................................................... 1 Related Devices ................................................................................. 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 Timing Characteristics..................................................................... 4 Absolute Maximum Ratings............................................................ 5 ESD Caution.................................................................................. 5 Pin Configuration and Function Description .............................. 6 Typical Performance Characteristics ............................................. 7 Terminology .................................................................................... 10 Theory of Operation ...................................................................... 11 DAC Section................................................................................ 11 Resistor String ............................................................................. 11 Output Amplifier........................................................................ 11 Interpolator Architecture .......................................................... 11 Serial Interface ............................................................................ 12 Input Shift Register .................................................................... 12 SYNC Interrupt .......................................................................... 12 Power-On Reset.......................................................................... 12 Microprocessor Interfacing....................................................... 13 Applications..................................................................................... 14 Closed-Loop Applications ........................................................ 14 Filter ............................................................................................. 14 Choosing a Reference for the AD5680.................................... 15 Using a Reference as a Power Supply for the AD5680 .......... 16 Using the AD5680 with a Galvanically Isolated Interface .... 16 Power Supply Bypassing and Grounding................................ 16 Outline Dimensions ....................................................................... 17 Ordering Guide .......................................................................... 17
REVISION HISTORY
6/06--Revision 0: Initial Version
Rev. 0 | Page 2 of 20
AD5680 SPECIFICATIONS
VDD = 4.5 V to 5.5 V; RL = 2 k to GND; CL = 200 pF to GND; VREF = VDD; all specifications TMIN to TMAX, unless otherwise noted. Table 1.
Parameter STATIC PERFORMANCE 2 Resolution Relative Accuracy Differential Nonlinearity 3 Zero-Code Error Full-Scale Error Offset Error Gain Error Zero-Code Error Drift Gain Temperature Coefficient DC Power Supply Rejection Ratio OUTPUT CHARACTERISTICS3 Output Voltage Range Output Voltage Settling Time Slew Rate Capacitive Load Stability Output Noise Spectral Density 4 Output Noise (0.1 Hz to 10 Hz)4 Total Harmonic Distortion (THD)4 Digital-to-Analog Glitch Impulse Digital Feedthrough DC Output Impedance Short-Circuit Current4 REFERENCE INPUT Reference Current Reference Input Range 5 Reference Input Impedance LOGIC INPUTS Input Current VINL, Input Low Voltage VINH, Input High Voltage Pin Capacitance POWER REQUIREMENTS VDD IDD (Normal Mode) VDD = 4.5 V to 5.5 V POWER EFFICIENCY IOUT/IDD
1 2 3
Min 18
B Grade Typ Max
Unit Bits LSB LSB LSB mV % FSR mV % FSR V/C ppm dB V s V/s nF nF nV/Hz V p-p dB nV-s nV-s mA
B Version 1 Conditions/Comments
32
2 -0.2
64 1 2 10 -1 10 1.5
Measured in 50 Hz system bandwidth Measured in 300 Hz system bandwidth All 0s loaded to DAC register All 1s loaded to DAC register
2 2.5 -100 0 80 1.5 2 10 80 25 -80 5 0.2 0.5 30 40 0.75 125 2 0.8 2 3 4.5 325 85 5.5 450 75 VDD VDD 85
Of FSR/C DAC code = midscale; VDD = 5 V 10%
1/4 to 3/4 scale change settling to 8 LSB RL = 2 k; 0 pF < CL < 200 pF 1/4 to 3/4 scale RL = RL = 2 k DAC code = midscale, 10 kHz DAC code = midscale VREF = 2 V 300 mV p-p, f = 200 Hz 1 LSB change around major carry
VDD = 5 V VREF = VDD = 5 V
A V k A V V pF V A %
All digital inputs VDD = 5 V VDD = 5 V
All digital inputs at 0 V or VDD DAC active and excluding load current VIH = VDD and VIL = GND ILOAD = 2 mA, VDD = 5 V
Temperature range for B version is -40C to +105C, typical at +25C. DC specifications tested with the outputs unloaded, unless otherwise stated. Linearity calculated using a reduced code range of 2048 to 260096. Guaranteed by design and characterization; not production tested. 4 Output unloaded. 5 Reference input range at ambient where maximum DNL specification is achievable.
Rev. 0 | Page 3 of 20
AD5680 TIMING CHARACTERISTICS
All input signals are specified with tr = tf = 1 ns/V (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. See Figure 2. VDD = 4.5 V to 5.5 V; all specifications TMIN to TMAX, unless otherwise noted. Table 2.
Parameter t1 1 t2 t3 t4 t5 t6 t7 t8 t9 t10
1
Limit at TMIN, TMAX VDD = 4.5 V to 5.5 V 33 13 13 13 5 4.5 0 33 13 0
Unit ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min
Conditions/Comments SCLK cycle time SCLK high time SCLK low time SYNC to SCLK falling edge setup time Data setup time Data hold time SCLK falling edge to SYNC rising edge Minimum SYNC high time SYNC rising edge to SCLK fall ignore SCLK falling edge to SYNC fall ignore
Maximum SCLK frequency is 30 MHz at VDD = 4.5 V to 5.5 V.
t10
SCLK
t1
t9
t8
SYNC
t4
t3
t2
t7
DIN
DB23
DB0
Figure 2. Serial Write Operation
Rev. 0 | Page 4 of 20
05854-002
t5
t6
AD5680 ABSOLUTE MAXIMUM RATINGS
TA = 25C, unless otherwise noted. Table 3.
Parameter VDD to GND VOUT to GND VFB to GND VREF to GND Digital Input Voltage to GND Operating Temperature Range Industrial (B Version) Storage Temperature Range Junction Temperature (TJ max) Power Dissipation SOT-23 Package (4-Layer Board) JA Thermal Impedance Reflow Soldering Peak Temperature Pb-free Rating -0.3 V to +7 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V -40C to +105C -65C to +150C 150C (TJ max - TA)/JA 119C/W 260C
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
Rev. 0 | Page 5 of 20
AD5680 PIN CONFIGURATION AND FUNCTION DESCRIPTION
VDD 1 VREF 2
8
GND
VOUT 4
5
SYNC
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No. 1 2 3 4 5 Mnemonic VDD VREF VFB VOUT SYNC Function Power Supply Input. The part can be operated from 4.5 V to 5.5 V. VDD should be decoupled to GND. Reference Voltage Input. Feedback Connection for the Output Amplifier. VFB should be connected to VOUT for normal operation. Analog Output Voltage from DAC. The output amplifier has rail-to-rail operation. Level-Triggered Control Input (Active Low). This is the frame synchronization signal for the input data. When SYNC goes low, it enables the input shift register and data is transferred in on the falling edges of the following clocks. The DAC is updated following the 24th clock cycle unless SYNC is taken high before this edge, in which case the rising edge of SYNC acts as an interrupt and the write sequence is ignored by the DAC. Serial Clock Input. Data is clocked into the input shift register on the falling edge of the serial clock input. Data can be transferred at rates up to 30 MHz. Serial Data Input. This device has a 24-bit shift register. Data is clocked into the register on the falling edge of the serial clock input. Ground Reference Point (for all circuitry on the part).
6 7 8
SCLK DIN GND
Rev. 0 | Page 6 of 20
05854-003
DIN TOP VIEW VFB 3 (Not to Scale) 6 SCLK
7
AD5680
AD5680 TYPICAL PERFORMANCE CHARACTERISTICS
40 VDD = VREF = 5V 32 TA = 25C 24 16
INL ERROR (LSB) ERROR (% FSR)
0 -0.02 -0.04 -0.06 -0.08 -0.01 -0.12 -0.14 FULL-SCALE ERROR VDD = 5V
GAIN ERROR
8 0 -8 -16 -24 -32 -40 0 40k 80k 120k 160k CODE 200k 240k
05854-028
-0.16 -0.18 -0.20 -40 -20 0 20 40 60 TEMPERATURE (C) 80 100
05302-023
Figure 4. Typical INL Plot
1.0 0.8 0.6
DNL ERROR (LSB)
Figure 7. Gain Error and Full-Scale Error vs. Temperature
VDD = VREF = 5V TA = 25C
1.5 1.0 0.5
ERROR (mV)
ZERO-SCALE ERROR
0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 0 25k 50k 75k 100k 125k 150k 175k 200k 225k 250k CODE
05854-029
0 -0.5 -1.0 -1.5 OFFSET ERROR
05302-024
-2.0 -2.5 -40
-20
0
20 40 60 TEMPERATURE (C)
80
100
Figure 5. Typical DNL Plot in 50 Hz System Bandwidth
Figure 8. Zero-Scale Error and Offset Error vs. Temperature
0.20
4
VDD = 4.5V TO 5.5V T = -40C TO +105C
0.15 0.10
VDD = VREF = 5V, 3V TA = 25C
DAC LOADED WITH ZERO SCALE - SINKING CURRENT
ERROR VOLTAGE (V)
2
0.05 0 -0.05 -0.10 -0.15 -0.20
05854-014
DNL (LSB)
1
DAC LOADED WITH FULL SCALE - SOURCING CURRENT -4 -3 -2 -1 0 I (mA) 1 2 3 4 5
0
300 50 SYSTEM BANDWIDTH (Hz)
>300
Figure 6. DNL Performance vs. System Bandwidth
05854-042
0
-0.25 -5
Figure 9. Headroom at Rails vs. Source and Sink Current
Rev. 0 | Page 7 of 20
AD5680
450
400 350 300 VDD = VREF = 5V TA = 25C
SCLK 1 DIN 2 : 1.52V : 64.8s @: 1.20V
IDD (A)
250 200 150 100 50
05854-007
VOUT
0
3
0
4000
8000
12000 CODE
16000
20000
24000
CH1 2.00V CH3 1.00V
CH2 2.00V
M 20.0s
CH4
1.30V
Figure 10. Supply Current vs. Code
350 300 250 200 VDD = VREF = 5V
Figure 13. Full-Scale Settling Time, 5 V
1
VDD
IDD (A)
2
150 100 50 0 -40
VREF
VOUT C3 MAX 284mV VOUT C3 MIN -52mV
VOUT
05854-016
3
-20
0
20
40
60
80
100
TEMPERATURE (C)
05854-006
CH1 3.00V CH2 3.00V CH3 100mV
M 100s
CH1
2.40V
Figure 11. Supply Current vs. Temperature
Figure 14. Power-On Reset to 0 V
700 600
TA = 25C VDD = 5V
500 400 300 200 100 0
1 2
VDD
IDD (A)
VREF
VOUT C3 MAX 2.5V VOUT C3 MIN -40mV
VOUT
05854-017
3
05854-004
0
1
2 VLOGIC (V)
3
4
5
CH1 3.00V CH2 3.00V CH3 500mV
M 100s
CH1
2.40V
Figure 12. Supply Current vs. Logic Input Voltage
Figure 15. Power-On Reset to Midscale
Rev. 0 | Page 8 of 20
05854-015
AD5680
2.502500 2.502250 2.502000 2.501750 2.501500 2.501250
AMPLITUDE
VDD = VREF = 5V TA = 25C 13nS/SAMPLE NUMBER 1 LSB CHANGE AROUND MIDSCALE (0x20000 TO 0x1FFFF) GLITCH IMPULSE = 2.723nV.s
16 VREF = VDD TA = 25C 14 VDD = 3V 12
2.500750 2.500500 2.500250 2.500000 2.499750 2.499500 2.499000 2.498750
05854-005
TIME (s)
2.501000
10
8
VDD = 5V
0
50
100
150 200 250 300 350 SAMPLE NUMBER
400
450 500 550
4
0
1
2
3
4 5 6 7 CAPACITANCE (nF)
8
9
10
Figure 16. Digital-to-Analog Glitch Impulse (Negative)
2.5010 2.5008 2.5006 2.5004 2.5002
Figure 19. Settling Time vs. Capacitive Load
VDD = VREF = 5V TA = 25C DAC LOADED WITH MIDSCALED DIGITAL FEEDTHROUGH = 0.201nV
VDD = VREF = 5V TA = 25C DAC LOADED WITH MIDSCALE
AMPLITUDE
2.5000
5V/DIV
2.4998 2.4996 2.4994 2.4992 2.4990
05854-020
1
VREF
2.4986 0
50
100
150
200 250 300 350 SAMPLES x 6.5ns
400
450
500
5s/DIV
Figure 17. Digital Feedthrough
-20 -30 -40 -50
Figure 20. 0.1 Hz to 10 Hz Output Noise Plot
1000 900 800 700
VDD = 5V TA = 25C FULLSCALE LOADED VREF = 2V 300mV p-p
VDD = VREF = 5V TA = 25C MIDSCALE LOADED
NOISE (nV/Hz)
600 500 400 300
(dB)
-60 -70 -80
05854-018
200 100 0 100 1k 10k FREQUENCY (Hz) 100k
05854-013
-90 -100 0 1 2 3 4 5 6 FREQUENCY (kHz) 7 8 9
10
1M
Figure 18. Total Harmonic Distortion
Figure 21. Noise Spectral Density
Rev. 0 | Page 9 of 20
05854-019
2.4988
05854-027
2.499250
6
AD5680 TERMINOLOGY
Relative Accuracy or Integral Nonlinearity (INL) For the DAC, relative accuracy or integral nonlinearity is a measurement of the maximum deviation, in LSBs, from a straight line passing through the endpoints of the DAC transfer function. Figure 4 shows a typical INL vs. code plot. Differential Nonlinearity (DNL) Differential nonlinearity is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of 1 LSB maximum ensures monotonicity. Figure 5 shows a typical DNL vs. code plot. Zero-Code Error Zero-code error is a measurement of the output error when zero code (0x00000) is loaded to the DAC register. Ideally, the output should be 0 V. The zero-code error is always positive in the AD5680 because the output of the DAC cannot go below 0 V. It is due to a combination of the offset errors in the DAC and the output amplifier. Zero-code error is expressed in mV. A plot of zero-code error vs. temperature can be seen in Figure 7. Full-Scale Error Full-scale error is a measurement of the output error when fullscale code (0x3FFFF) is loaded to the DAC register. Ideally, the output should be VDD - 1 LSB. Full-scale error is expressed in percent of full-scale range. Gain Error This is a measure of the span error of the DAC. It is the deviation in slope of the DAC transfer characteristic from ideal expressed as a percent of the full-scale range. Zero-Code Error Drift This is a measurement of the change in zero-code error with a change in temperature. It is expressed in V/C. Gain Temperature Coefficient This is a measurement of the change in gain error with changes in temperature. It is expressed in (ppm of full-scale range)/C. Offset Error Offset error is a measure of the difference between VOUT (actual) and VOUT (ideal) expressed in mV in the linear region of the transfer function. Offset error is measured on the AD5680 with Code 2048 loaded in the DAC register. It can be negative or
positive.
DC Power Supply Rejection Ratio (PSRR) This indicates how the output of the DAC is affected by changes in the supply voltage. PSRR is the ratio of the change in VOUT to a change in VDD for full-scale output of the DAC. It is measured in dB. VREF is held at 2 V, and VDD is varied by 10%. Output Voltage Settling Time This is the amount of time it takes for the output of a DAC to settle to a specified level for a 1/4 to 3/4 full-scale input change and is measured from the 24th falling edge of SCLK. Digital-to-Analog Glitch Impulse Digital-to-analog glitch impulse is injected into the analog output when the input code in the DAC register changes state. It is normally specified as the area of the glitch in nV-s, and is measured when the digital input code is changed by 1 LSB at the major carry transition (0x1FFFF to 0x20000). See Figure 16. Digital Feedthrough Digital feedthrough is a measure of the impulse injected into the analog output of the DAC from the digital inputs of the DAC, but is measured when the DAC output is not updated. It is specified in nV-s and measured with a full-scale code change on the data bus, that is, from all 0s to all 1s and vice versa. Total Harmonic Distortion (THD) This is the difference between an ideal sine wave and its attenuated version using the DAC. The sine wave is used as the reference for the DAC. The THD is a measurement of the harmonics present on the DAC output. It is measured in dB. Noise Spectral Density This is a measurement of the internally generated random noise. Random noise is characterized as a spectral density (voltage per Hz). It is measured by loading the DAC to midscale and measuring noise at the output. It is measured in nV/Hz. Figure 21 shows a plot of noise spectral density.
Rev. 0 | Page 10 of 20
AD5680 THEORY OF OPERATION
DAC SECTION
The AD5680 DAC is fabricated on a CMOS process. The architecture consists of a string DAC followed by an output buffer amplifier. Figure 22 shows a block diagram of the DAC architecture.
VDD REF (+) DAC REGISTER RESISTOR STRING REF (-) OUTPUT AMPLIFIER R VOUT R VFB
OUTPUT AMPLIFIER
The output buffer amplifier can generate rail-to-rail voltages on its output, which gives an output range of 0 V to VDD. This output buffer amplifier has a gain of 2 derived from a 50 k resistor divider network in the feedback path. The output amplifier's inverting input is available to the user, allowing for remote sensing. This VFB pin must be connected to VOUT for normal operation. It can drive a load of 2 k in parallel with 1000 pF to GND. The source and sink capabilities of the output amplifier can be seen in Figure 9. The slew rate is 1.5 V/s with a 1/4 to 3/4 fullscale settling time of 10 s.
05854-030
GND
INTERPOLATOR ARCHITECTURE
The AD5680 contains a 16-bit DAC with an internal clock generator and interpolator. The voltage levels generated by the 16-bit, 1 LSB step can be subdivided using the interpolator to increase the resolution to 18 bits. The 18-bit input code can be divided into two segments: 16-bit DAC code (DB19 to DB4) and 2-bit interpolator code (DB3 and DB2). The input to the DAC is switched between a 16-bit code (for example, Code 1023) and a 16-bit code + 1 LSB (for example, Code 1024). The 2-bit interpolator code determines the duty cycle of the switching and hence the 18-bit code level. See Table 5 for an example. Table 5.
18-Bit Code DB19 to DB2 4092 4093 4094 4095 4096 16-Bit DAC Code DB19 to DB4 1023 1023 1023 1023 1024 2-Bit Interpolator Code DB3 DB2 0 0 0 1 1 0 1 1 0 0
Figure 22. DAC Architecture
Because the input coding to the DAC is straight binary, the ideal output voltage is given by
D VOUT = VREF x 262144
where D is the decimal equivalent of the binary code that is loaded to the DAC register. It can range from 0 to 262143.
RESISTOR STRING
The resistor string section is shown in Figure 23. It is simply a string of resistors, each of value R. The code loaded to the DAC register determines at which node on the string the voltage is tapped off to be fed into the output amplifier. The voltage is tapped off by closing one of the switches connecting the string to the amplifier. Because it is a string of resistors, it is guaranteed monotonic.
R
Duty Cycle 0 25% 50% 75% 0
R
R
TO OUTPUT AMPLIFIER
The DAC output voltage is given by the average value of the waveform switching between 16-bit code (C) and 16-bit code + 1 (C + 1). The output voltage is a function of the duty cycle of the switching.
FILTER 18-BIT INPUT CODE 18 PLANT C MUX 16 DAC VOUT 75% DUTY CYCLE 50% DUTY CYCLE
05854-032
16 C + 1 +1
R
2 INTERPOLATOR
C+1 C C+1 C C+1 C
25% DUTY CYCLE
R
05854-031
CLK
Figure 24. Interpolation Architecture
Figure 23. Resistor String
Rev. 0 | Page 11 of 20
AD5680
SERIAL INTERFACE
The AD5680 has a 3-wire serial interface (SYNC, SCLK, and DIN) that is compatible with SPI, QSPI, and MICROWIRE interface standards as well as with most DSPs. See Figure 2 for a timing diagram of a typical write sequence. The write sequence begins by bringing the SYNC line low. Data from the DIN line is clocked into the 24-bit shift register on the falling edge of SCLK. The serial clock frequency can be as high as 30 MHz, making the AD5680 compatible with high speed DSPs. On the 24th falling clock edge, the last data bit is clocked in and the programmed function is executed, that is, a change in DAC register contents occurs. At this stage, the SYNC line can be kept low or be brought high. In either case, it must be brought high for a minimum of 33 ns before the next write sequence so that a falling edge of SYNC can initiate the next write sequence. Because the SYNC buffer draws more current when VIN = 2 V than it does when VIN = 0.8 V, SYNC should be idled low between write sequences for even lower power operation. As mentioned previously it must, however, be brought high again just before the next write sequence.
INPUT SHIFT REGISTER
The input shift register is 24 bits wide (see Figure 25). The first four bits are don't care bits. The next 18 bits are the data bits followed by two don't care bits. These are transferred to the DAC register on the 24th falling edge of SCLK.
SYNC INTERRUPT
In a normal write sequence, the SYNC line is kept low for at least 24 falling edges of SCLK, and the DAC is updated on the 24th falling edge. However, if SYNC is brought high before the 24th falling edge, this acts as an interrupt to the write sequence. The shift register is reset and the write sequence is seen as invalid. Neither an update of the DAC register contents nor a change in the operating mode occurs (see Figure 26).
POWER-ON RESET
The AD5680 family contains a power-on reset circuit that controls the output voltage during power-up. The AD5680-1 DAC output powers up to 0 V, and the AD5680-2 DAC output powers up to midscale. The output remains there until a valid write sequence is made to the DAC. This is useful in applications where it is important to know the output state of the DAC while it is in the process of powering up.
DB23 (MSB) X X X X D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X
DB0 (LSB) X
05854-033
DATA BITS
Figure 25. Input Register Contents
SCLK
SYNC
DIN
DB23
DB0
DB23
DB0
05854-034
INVALID WRITE SEQUENCE: SYNC HIGH BEFORE 24TH FALLING EDGE
VALID WRITE SEQUENCE, OUTPUT UPDATES ON THE 24TH FALLING EDGE
Figure 26. SYNC Interrupt Facility
Rev. 0 | Page 12 of 20
AD5680
MICROPROCESSOR INTERFACING
AD5680 to Blackfin(R) ADSP-BF53x Interface
Figure 27 shows a serial interface between the AD5680 and the Blackfin ADSP-BF53x microprocessor. The ADSP-BF53x processor family incorporates two dual-channel synchronous serial ports, SPORT1 and SPORT0, for serial and multiprocessor communications. Using SPORT0 to connect to the AD5680, the setup for the interface is as follows. DT0PRI drives the DIN pin of the AD5680, while TSCLK0 drives the SCLK of the part. The SYNC is driven from TFS0.
ADSP-BF53x*
AD5680 to 80C51/80L51 Interface
Figure 29 shows a serial interface between the AD5680 and the 80C51/80L51 microcontroller. The setup for the interface is as follows. TxD of the 80C51/80L51 drives SCLK of the AD5680, while RxD drives the serial data line of the part. The SYNC signal is again derived from a bit-programmable pin on the port. In this case, port line P3.3 is used. When data is to be transmitted to the AD5680, P3.3 is taken low. The 80C51/80L51 transmits data in 8-bit bytes only; thus only eight falling clock edges occur in the transmit cycle. To load data to the DAC, P3.3 is left low after the first eight bits are transmitted, and a second write cycle is initiated to transmit the second byte of data. P3.3 is taken high following the completion of this cycle. The 80C51/80L51 outputs the serial data in a format that has the LSB first. The AD5680 must receive data with the MSB first. The 80C51/80L51 transmit routine should take this into account.
80C51/80L51*
AD5680*
SYNC DIN SCLK
05854-035
TFS0 DTOPRI TSCLK0
*ADDITIONAL PINS OMITTED FOR CLARITY
AD5680*
SYNC SCLK DIN
05854-037 05854-038
Figure 27. AD5680 to Blackfin ADSP-BF53x Interface
P3.3
AD5680 to 68HC11/68L11 Interface
Figure 28 shows a serial interface between the AD5680 and the 68HC11/68L11 microcontroller. SCK of the 68HC11/68L11 drives the SCLK of the AD5680, while the MOSI output drives the serial data line of the DAC. The SYNC signal is derived from a port line (PC7). The setup conditions for correct operation of this interface are as follows. The 68HC11/68L11 is configured with its CPOL bit as 0 and its CPHA bit as 1. When data is being transmitted to the DAC, the SYNC line is taken low (PC7). When the 68HC11/68L11 is configured this way, data appearing on the MOSI output is valid on the falling edge of SCK. Serial data from the 68HC11/68L11 is transmitted in 8-bit bytes with only eight falling clock edges occurring in the transmit cycle. Data is transmitted MSB first. To load data to the AD5680, PC7 is left low after the first eight bits are transferred, and a second serial write operation is performed to the DAC; PC7 is taken high at the end of this procedure.
68HC11/68L11*
TxD RxD
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 29. AD5680 to 80C51/80L51 Interface
AD5680 to MICROWIRE Interface
Figure 30 shows an interface between the AD5680 and any MICROWIRE-compatible device. Serial data is shifted out on the falling edge of the serial clock and is clocked into the AD5680 on the rising edge of the SK.
MICROWIRE*
AD5680*
SYNC SCLK DIN
CS SK SO
AD5680*
SYNC SCLK DIN
05854-036
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 30. AD5680 to MICROWIRE Interface
PC7 SCK MOSI
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 28. AD5680 to 68HC11/68L11 Interface
Rev. 0 | Page 13 of 20
AD5680 APPLICATIONS
CLOSED-LOOP APPLICATIONS
The AD5680 is suitable for closed-loop low bandwidth applications. Ideally, the system bandwidth acts as a filter on the DAC output. (See the Filter section for details of the DAC output prefiltering and postfiltering.) The DAC updates at the interpolation frequency of 10 kHz.
PLANT CONTROLLER DAC
2
: 2.09ms @: 1.28ms
CODE 4092
05854-039
CODE 4094
05854-025
1
ADC
CH1 20.0V CH2 5V
M 500s
CH2
1.4V
Figure 33. DAC Output with 50 Hz Filter on Output Figure 31. Typical Closed-Loop Application
FILTER
The DAC output voltage for code transition 4092 to 4094 can be seen in Figure 32. This is the DAC output unfiltered. Code 4092 does not have any interpolation but code 4094 has interpolation with a 50% duty cycle. See Table 5. Figure 33 shows the DAC output with a 50 Hz passive RC filter and Figure 34 shows the output with a 300 Hz passive RC filter. An RC combination of 320 k and 10 nF has been used to achieve the 50 Hz cutoff frequency, and an RC combination of 81 k and 10 nF has been used to achieve the 300 Hz cutoff frequency.
2
: 2.09ms @: 1.28ms
1
CODE 4092
CODE 4094
05854-026
CH1 20.0V CH2 5V
M 500s
CH2
1.4V
Figure 34. DAC Output with 300 Hz Filter on Output
CODE 4092
1
CODE 4094
05854-024
CH1 20.0V
M 500s
CH4
0V
Figure 32. DAC Output Unfiltered
Rev. 0 | Page 14 of 20
AD5680
CHOOSING A REFERENCE FOR THE AD5680
To achieve the optimum performance from the AD5680, choose a precision voltage reference carefully. The AD5680 has only one reference input, VREF. The voltage on the reference input is used to supply the positive input to the DAC. Therefore any error in the reference is reflected in the DAC. When choosing a voltage reference for high accuracy applications, the sources of error are initial accuracy, ppm drift, longterm drift, and output voltage noise. Initial accuracy on the output voltage of the DAC leads to a full-scale error in the DAC. To minimize these errors, a reference with high initial accuracy is preferred. Also, choosing a reference with an output trim adjustment, such as the ADR425, allows a system designer to trim out system errors by setting a reference voltage to a voltage other than the nominal. The trim adjustment can also be used at temperature to trim out any error. Long-term drift is a measurement of how much the reference drifts over time. A reference with a tight long-term drift specification ensures that the overall solution remains relatively stable during its entire lifetime. The temperature coefficient of a reference's output voltage affects INL, DNL, and TUE. A reference with a tight temperature coefficient specification should be chosen to reduce temperature dependence of the DAC output voltage in ambient conditions. In high accuracy applications, which have a relatively low noise budget, reference output voltage noise needs to be considered. It is important to choose a reference with as low an output noise voltage as practical for the system noise resolution required. Precision voltage references such as the ADR425 produce low output noise in the 0.1 Hz to 10 Hz range. Examples of recommended precision references for use as supply to the AD5680 are shown in the Table 6.
Table 6. Partial List of Precision References for Use with the AD5680
Part No. ADR425 ADR395 REF195 Initial Accuracy (mV max) 2 6 2 Temp. Drift (ppmoC max) 3 25 5 0.1 Hz to 10 Hz Noise (V p-p typ) 3.4 5 50 VOUT (V) 5 5 5
Rev. 0 | Page 15 of 20
AD5680
USING A REFERENCE AS A POWER SUPPLY FOR THE AD5680
Because the supply current required by the AD5680 is extremely low, an alternative option is to use a voltage reference to supply the required voltage to the part (see Figure 35). This is especially useful if the power supply is quite noisy, or if the system supply voltages are at some value other than 5 V, for example, 15 V. The voltage reference outputs a steady supply voltage for the AD5680; see Table 6 for a suitable reference. If the low dropout REF195 is used, it must supply 325 A of current to the AD5680, with no load on the output of the DAC. When the DAC output is loaded, the REF195 also needs to supply the current to the load. The total current required (with a 5 k load on the DAC output) is 325 A + (5 V/5 k) = 1.33 mA The load regulation of the REF195 is typically 2 ppm/mA, which results in a 2.7 ppm (13.5 V) error for the 1.33 mA current drawn from it. This corresponds to a 0.177 LSB error.
15V 5V 250A
5V REGULATOR POWER
10F
0.1F
VDD SCLK V1A VOA SCLK
ADuM1300
SDI V1B VOB SYNC
AD5680
VOUT
DATA
V1C
VOC
DIN
05854-041
GND
Figure 36. AD5680 with a Galvanically Isolated Interface
POWER SUPPLY BYPASSING AND GROUNDING
When accuracy is important in a circuit, it is helpful to carefully consider the power supply and ground return layout on the board. The printed circuit board containing the AD5680 should have separate analog and digital sections, each having its own area of the board. If the AD5680 is in a system where other devices require an AGND-to-DGND connection, the connection should be made at one point only. This ground point should be as close as possible to the AD5680. The power supply to the AD5680 should be bypassed with 10 F and 0.1 F capacitors. The capacitors should be located as close as possible to the device, with the 0.1 F capacitor ideally right up against the device. The 10 F capacitors are the tantalum bead type. It is important that the 0.1 F capacitor has low effective series resistance (ESR) and effective series inductance (ESI), for example, common ceramic types of capacitors. This 0.1 F capacitor provides a low impedance path to ground for high frequencies caused by transient currents due to internal logic switching. The power supply line itself should have as large a trace as possible to provide a low impedance path and to reduce glitch effects on the supply line. Clocks and other fast switching digital signals should be shielded from other parts of the board by digital ground. Avoid crossover of digital and analog signals if possible. When traces cross on opposite sides of the board, ensure that they run at right angles to each other to reduce feedthrough effects on the board. The best board layout technique is the microstrip technique where the component side of the board is dedicated to the ground plane only and the signal traces are placed on the solder side. However, this is not always possible with a 2-layer board.
REF195
Figure 35. REF195 as Power Supply to the AD5680
USING THE AD5680 WITH A GALVANICALLY ISOLATED INTERFACE
In process-control applications in industrial environments, it is often necessary to use a galvanically isolated interface to protect and isolate the controlling circuitry from any hazardous common-mode voltages that might occur in the area where the DAC is functioning. Isocouplers provide isolation in excess of 3 kV. The AD5680 uses a 3-wire serial logic interface, so the ADuM130x 3-channel digital isolator provides the required isolation (see Figure 36). The power supply to the part also needs to be isolated, which is done by using a transformer. On the DAC side of the transformer, a 5 V regulator provides the 5 V supply required for the AD5680.
05854-040
3-WIRE SERIAL INTERFACE
SYNC SCLK DIN
VDD VREF
AD5680
VOUT = 0V TO 5V
Rev. 0 | Page 16 of 20
AD5680 OUTLINE DIMENSIONS
2.90 BSC
8 7 6 5
1.60 BSC
1 2 3 4
2.80 BSC
PIN 1 INDICATOR 0.65 BSC 1.30 1.15 0.90 1.95 BSC
1.45 MAX 0.38 0.22
0.22 0.08 8 4 0
0.15 MAX
SEATING PLANE
0.60 0.45 0.30
COMPLIANT TO JEDEC STANDARDS MO-178-BA
Figure 37. 8-Lead Small Outline Transistor Package [SOT-23] (RJ-8) Dimensions shown in millimeters
ORDERING GUIDE
Model AD5680BRJZ-1500RL7 1 AD5680BRJZ-1REEL71 AD5680BRJZ-2500RL71 AD5680BRJZ-2REEL71 EVAL-AD5680EB
1
Temperature Range -40C to +105C -40C to +105C -40C to +105C -40C to +105C
Package Description 8-lead SOT-23 8-lead SOT-23 8-lead SOT-23 8-lead SOT-23 Evaluation Board
Package Option RJ-8 RJ-8 RJ-8 RJ-8
Branding D3C D3C D3D D3D
Power-On Reset to Code Zero Zero Midscale Midscale
Accuracy 64 LSB INL 64 LSB INL 64 LSB INL 64 LSB INL
Z = Pb-free part.
Rev. 0 | Page 17 of 20
AD5680 NOTES
Rev. 0 | Page 18 of 20
AD5680 NOTES
Rev. 0 | Page 19 of 20
AD5680 NOTES
(c)2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05854-0-6/06(0)
T T
Rev. 0 | Page 20 of 20


▲Up To Search▲   

 
Price & Availability of AD5680BRJZ-2500RL7

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X