|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
T R I Q U I N T S E M I C O N D U C T O R, I N C . The TQ6124 is a 14-bit monolithic digital-to-analog converter. The TQ6124 achieves conversion accuracy by using a segmented architecture, precision current sources, and on-chip nichrome resistors. The only external components required are an external reference and loop control amplifier. The TQ6124 is ideally suited for applications in direct digital synthesis, pixel generation for high-resolution monitors, broadband video generation, and high-speed arbitrary waveform generators. TQ6124 1 Gigasample/sec, 14-bit Digital-to-Analog Convertor Features Figure 1. TQ6124 Block Diagram * 1Gs/s aggregate bandwidth LSBs CLK NCLK D0 D1 D2 D3 D4 D5 D6 Intermediate Bits D7 D8 D9 MSBs D10 D11 D12 D13 * 14-bit resolution * RF front end * ECL-compatible inputs Master Latch * 0.026% DC differential non-linearity * 0.035% DC integral non-linearity MIXED SIGNAL PRODUCTS Delay Stages S1 S2 ... ... ... S14 S15 Segment Encoders * SFDR: 52 dBc @ FOUT = 75 MHz 48 dBc @ FOUT = 148 MHz 45 dBc @ FOUT = 199 MHz * 1.4 W power dissipation * 44-pin ceramic QFP package or die only Slave Latch Current Switches Applications * Direct Digital Synthesis * Pixel generation for workstations and high-end monitors 50 ohm R-2R Ladder Network VO VAA MID_trim LSB_trim VREF VSENSE NVO * Direct-generation of broadband video for cable TV * High-speed arbitrary waveform generators Current Source Array For additional information and latest specifications, see our website: www.triquint.com 1 TQ6124 Functional Description The TQ6124 registers incoming bits in a master latch array. The value of the four most-significant bits is encoded into an n-of-15 thermometer code while the ten low-order bits pass though an equalizing delay stage. All 25 bits are re-registered in a 25-wide slave latch array which drives a set of 25 differential pair switches. These switches steer the corresponding segment and bit currents into the true (VO) and complementary (NVO) outputs. This architecture minimizes glitch impulses by eliminating large mid-scale current transitions. The most-significant bits generate the segment currents, which are of equal weight at 1/16 of the fullscale output (IFS). The ten lower-order bits are divided into two subgroups. The three intermediate bits steer binary-weighted currents of magnitude IFS/32, IFS/64 and IFS/128 to the outputs. The seven least-significant bits steer identical IFS/128 currents into a differential R-2R ladder to generate effective bit currents of IFS/256 to IFS/16384. The DAC output is the sum of the outputs of the segments and the low-order bits. Clock and data inputs are ECL-compatible. The outputs are designed to operate into a 50 load, with internal reverse termination to ground being provided by the R-2R network. External compensation is utilized to minimize the effects of device mismatch. An external op amp senses the sum of the segment, the intermediate bit, and the LSB currents. Figure 2. TQ6124 Currents Segments 1 thru 15 VO NVO Q ID9 NQ 1.25mA 2.5mA ID8 .625mA ID7 dummy ID6 .3125mA (x8) dummy .3125mA To switches for D0 thru D9 .3125mA .3125mA VREF VSENSE R SENSE 5.8K R SOURCE 1.2K RSENSE 5.8K R SOURCE 1.2K VAA R SENSE 5.8K R SOURCE 1.2K MID_trim LSB_trim 2 For additional information and latest specifications, see our website: www.triquint.com TQ6124 Electrical Specifications Table 1. Recommended Operating Conditions Symbol VSS VAA TC Parameter Negative Power Supply Analog Power Supply Case Temperature Min. -5.25 -15.5 -20 Nom. -5.0 -12 Max. -4.75 -11.5 85 Unit V V C Table 2. DC Operating Characteristics Unless otherwise specified, measured over Recommended Operating Conditions with balanced 50 loads, VFS = 1.0 V. Symbol IAA ISS VREF IREF VIH VIL II VEREF REREF DNL INL VFS ROUT VO, NVO VZS VSENSE JC Parameter VAA Supply Current VSS Supply Current Reference Voltage Reference input current ECL Input High Voltage ECL Input Low Voltage ECL Input Current ECL Reference Voltage ECL Reference Resistance Differential non-linearity Integral non-linearity Full-scale symmetry Full-scale output voltage VO, NVO, output resistance ROUT Matching Output Voltage Zero Scale Voltage Sense output voltage Thermal Impedance Condition Min. Nom. -75 -285 Max. -90 -450 VAA + 3.75 25 -0.6 -1.5 25 Unit mA mA V mA V V mA V ohms %F.S. %F.S. mV V ohms % V mV V C/W MIXED SIGNAL PRODUCTS VEREF = -1.3 V VEREF = -1.3 V VSS = -5.0 V (Note 2) (Note 2) (Note 1) RL = 50 ohms VAA + 2.5 -25 -1.1 -2.5 -25 VAA + 3.0 -0.05 -0.05 -8 44 -2.5 -1.125 -50 VAA + 2.5 -1.34 400 0.026 0.035 2 -1.0 50.9 0.15 -40 15 0.05 0.05 8 -1.125 57 2.5 0 0 VAA + 3.75 Notes: 1. Full-scale symmetry is a measure of the balance between VO and NVO. For a full-scale output transition, the change in VO will match the change in NVO to within the specified amount. Any imbalance in the output loads will affect symmetry. 2. Linearity can interpreted as 10 bits at 1/2 LSB or as 11 bits at 1 LSB. The device is monotonic to 10 bits. Linearity is tested with the Mid_trim set for optimal DNL, with the LSB_trim pin open. For additional information and latest specifications, see our website: www.triquint.com 3 TQ6124 Table 3. AC Operating Characteristics Unless otherwise noted, measured over DC operating characteristics with balanced 50 loads, VFS = 0.8V, VIN = 0.8VP-P, input rise and fall times 300 ps. Symbol FCLK tR , tF tDS tDH tCLKHI tCLKLO SFDR* Parameter Clock Frequency At full scale Data Setup Time Data Hold Time Clock High Time Clock Low Time Spurious free dynamic range Condition 10% to 90% Min. 50 200 300 400 Typ. Max. 1000 350 Unit MHz ps ps ps ps FOUT = 75 MHz FOUT = 148 MHz FOUT = 199 MHz 400 45 45 45 52 52 49 ps dBc dBc dBc *Note: SFDR testing performed at FCLK = 600 MHz only. Table 4. Absolute Maximum Ratings Symbol VSS VAA VO, NVO VI II VREF IREF TSTG TJ Parameter Digital Supply Analog Supply Analog Output Voltage Digital Input Voltage Digital Input Current Reference Voltage Reference Current Power Dissipation Storage Temperature Operating Junction Temperature Min. -7.0 -16.0 -2.0 VSS - 0.5 -1.0 VAA-2 -1 -65 Max. Unit V V V V mA V mA W C C 2.0 +0.5 +1.0 0 1 5 150 150 Note: Absolute Maximum Ratings are those beyond which the integrity of the device cannot be guaranteed. If the device is subjected to the limits in the absolute maximum ratings, its reliability may be impaired. The Electrical Specifications tables provide conditions for actual device operation. 4 For additional information and latest specifications, see our website: www.triquint.com TQ6124 AC Timing The low-going transition of CLK latches the data. Production SFDR testing is performed with the clock transitioning in the center of the data eye. The timing of the clock transition with respect to the data can improve SFDR performance. Systems working to optimize SFDR can 'tune' this phase relationship to optimize the desired characteristic. Figure 3. AC Timing Relationships tDS Data tDH Clock Operating Notes Current Source Control Loop The full scale output voltage is set through the use of an external op amp, as shown in Figure 4. Nominal full scale output voltage can be achieved by using a voltage source. With this, control voltages on the op amp of around VAA+3V can be set. Adjusting the full scale output voltage can be achieved by toggling the inputs over full scale while adjusting the control voltage to achieve the desired level. VAA Figure 4. Adjusting the Full-Scale Output Voltage VAA 1K 620 20 K + 1 K 20 K 1 K 20 K 1 K MID_TRIM LSB_TRIM +VIN AD586 VOUT VREF - MC34071 VAA VAA VSENSE VREF Adjustment Range The output full scale voltage range can be set through the VREF input. Figure 5 shows the approximate relationship between VREF and VFS. Figure 5. Full-Scale Output Voltage vs. VREF 1.2 Full-Scale Output Voltage 1.0 0.8 0.6 0.4 0.2 -1 0 1 2 3 Reference Voltage (vs VAA) 4 For additional information and latest specifications, see our website: www.triquint.com 5 MIXED SIGNAL PRODUCTS TQ6124 Operating Notes (continued) Power Supplies Optimized performance depends on clean supplies. Utilize very low impedance negative supplies that are decoupled over a wide frequency range. The analog and digital grounds should be isolated at the chip, connecting to a single point ground on the circuit board. ECL Reference The single-ended data inputs switch against an internal reference of -1.3V (nominal). Variations among input buffers, or in VTT, may benefit from adjustments in the reference. The ECL reference pin may be driven externally. Its equivalent load is 400 ohms to -1.3V (nominal). Trim Adjustments The external trim adjustments for the midrange bits and the LSBs is optional. Trimming is performed by monitoring the attribute of greatest concern (INL, DNL, Spurious levels) while minimizing the unwanted effects. Trim inputs should be left open if not used. Signals Figure 6. TQ6124 Pinout 40 DGND 39 D 6 38 D 5 37 DGND 44 VSS 43 D9 42 D8 41 D 7 36 D 4 35 D 3 34 VSS VSS D10 D11 D12 D13 (MSB) DGND DGND DGND CLK NCLK VSS 1 2 3 4 5 6 7 8 9 10 11 33 32 31 30 29 28 27 26 25 24 23 VSS D2 D1 D 0 (LSB) DGND DGND ECLref LSBtrim Midtrim VAA VAA TQ6124 Top View 12 AGND 13 14 I REF AGND 15 16 NVO 17 AGND 18 AGND 19 20 VSNS 21 V REF VSS 6 For additional information and latest specifications, see our website: www.triquint.com VAA VO 22 TQ6124 Table 5. Signal-Pin Descriptions Signal DGND AGND D0 thru D13 VO, NVO CLK, NCLK IREF VSENSE VREF VSS VAA Mid_trim LSB_trim ECLref Pin(s) 6, 7, 8, 28, 29, 37, 40 13, 15, 18, 19 30, 31, 32, 35, 36, 38, 39, 41, 42, 43, 2, 3, 4, 5 17, 16 9, 10 14 20 21 1, 11, 12, 33, 34, 44 22, 23, 24 25 26 27 Description Ground connection for digital circuitry. Ground connection for analog circuitry. Data inputs. D0 is the least significant bit. ECL levels. True and complementary analog outputs. True and complementary clock inputs. ECL levels. Connect to AGND. Source of dummy currents in the switch array. Sense Output. Reference Input. Digital negative power supply. Analog negative power supply. Trim terminal for mid range bits. Trim terminal for LSB range bits. Optional ECL reference level adjustment. Thevinin equivalent is 1.3V nominally into 400 ohms. Equivalent voltage tracks with digital supply. MIXED SIGNAL PRODUCTS Typical Performance Data The graph in Figure 7 shows representative performance data of spurious free dynamic range (SFDR) vs. output frequency performance measured from TQ6124 devices. Data was collected at room temperature; note, however, that SFDR is not strongly dependendent on temperature. Optimum performance is obtained by utilizing as high a clock rate as practical. Figure 7. SFDR vs. Output Frequency -65 -60 -55 -50 SFDR -45 -40 -35 -30 0 50 100 150 200 250 300 350 400 450 500 FOUT For additional information and latest specifications, see our website: www.triquint.com 7 TQ6124 Packaging Figure 8. 44-pin QFP Package Dimensions Top View 0.805 .650 44 BottomView Pin 1 Index 1 A A Ceramic or metal lid .050 .015 BSC All dimensions in inches Section A-A Device .125 Seating plane .035 typ. .065 8 For additional information and latest specifications, see our website: www.triquint.com TQ6124 Ordering Information TQ6124-CM TQ6124-CD ETF6124 Additional Information 1 GS/s 14-bit DAC in 44-pin ceramic QFP 1 GS/s 14-bit DAC -- die only Engineering Test Fixture with TQ6124 device For latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint: Web: www.triquint.com Email: sales@tqs.com Tel: (503) 615-9000 Fax: (503) 615-8900 For technical questions and additional information on specific applications: Email: applications@tqs.com The information provided herein is believed to be reliable; TriQuint assumes no liability for inaccuracies or omissions. TriQuint assumes no responsibility for the use of this information, and all such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. TriQuint does not authorize or warrant any TriQuint product for use in life-support devices and/or systems. Copyright (c) 1997 TriQuint Semiconductor, Inc. All rights reserved. Revision 1.1.A November 1997 For additional information and latest specifications, see our website: www.triquint.com 9 MIXED SIGNAL PRODUCTS |
Price & Availability of TQ6124 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |