Part Number Hot Search : 
T500BN SP1674BK PMLL4448 LL0APP FAITD75J MMSZ5227 SK315 ADP151AU
Product Description
Full Text Search
 

To Download ZL30406 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 ZL30406 SONET/SDH Clock Multiplier PLL
Data Sheet Features
* * * * * * * * Meets jitter requirements of Telcordia GR-253CORE for OC-48, OC-12, and OC-3 rates Meets jitter requirements of ITU-T G.813 for STM16, STM-4 and STM-1 rates Provides four LVPECL differential output clocks at 77.76 MHz Provides a CML differential clock programmable to 19.44 MHz, 38.88 MHz, 77.76 MHz and 155.52 MHz Provides a single-ended CMOS clock at 19.44 MHz Provides enable/disable control of output clocks Accepts a CMOS reference at 19.44 MHz 3.3 V supply Ordering Information ZL30406QGC 64 Pin TQFP
May 2003
-40C to +85C
Description
The ZL30406 is an analog phase-locked loop (APLL) designed to provide rate conversion and jitter attenuation for SDH (Synchronous Digital Hierarchy) and SONET (Synchronous Optical Network) networking equipment. The ZL30406 generates very low jitter clocks that meet the jitter requirements of Telcordia GR-253-CORE OC-48, OC-12, OC-3, OC-1 rates and ITU-T G.813 STM-16, STM-4 and STM-1 rates. The ZL30406 accepts a CMOS compatible reference at 19.44 MHz and generates four LVPECL differential output clocks at 77.76 MHz, a CML differential clock programmable to 19.44 MHz, 38.88 MHz, 77.76 MHz and 155.52 MHz and a single-ended CMOS clock at 19.44 MHz. The output clocks can be individually enabled or disabled.
Applications
* * SONET/SDH line cards Network Element timing cards
LPF
C77oEN-A C77oEN-B OC-CLKoEN
C77o, C155o C19o, C38o, CML-P/N outputs
OC-CLKoP/N C19i Frequency & Phase Detector 19.44MHz BIAS
Reference & Bias circuit
Loop Filter
Output
VCO
Interface Circuit
C77oP/N-A C77oP/N-B C77oP/N-C C77oP/N-D C19o
VDD GND
VCC
FS1-2
C19oEN C77oEN-C C77oEN-D 15
Figure 1 - Functional Block Diagram
1
ZL30406
Data Sheet
GND VCC1 VCC OC-CLKoN OC-CLKoP GND VCC2 LPF GND GND BIAS OC-CLKoEN C77oEN-A C77oEN-B C77oEN-C C77oEN-D
GND C77oN-A C77oP-A VCC GND C77oP-B C77oN-B VCC GND C77oN-C C77oP-C VCC GND C77oP-D C77oN-D VCC 64
2 4 44 6 8 10 38 12 36 14 34 16 18 20 22 24 26 28 30 32 42 40
62
60
58
56
54
52
50
48 46
65 - EP_GND
ZL30406
GND VCC VDD GND VCC GND VDD GND NC GND GND NC GND C19o VDD GND
Figure 2 - TQFP 64 pin (Top View)
Pin Description
Pin Description Table Pin # 1 2 3 4 5 6 7 8 9 10 11 Name GND VCC1 VCC OC-CLKoN OC-CLKoP GND VCC2 LPF GND GND BIAS Ground. 0 volt. Positive Analog Power Supply. +3.3V 10%. Positive Analog Power Supply. +3.3V 10%. SONET/SDH Clock (CML Output). These outputs provide a programmable differential CML clock at 19.44 MHz, 38.88 MHz, 77.76 MHz and 155.52 MHz. The output frequency is selected with FS2 and FS1 pins. Ground. 0 volt Positive Analog Power Supply. +3.3V 10% Low Pass Filter (Analog). Connect to this pin external RC network (RF and CF) for the low pass filter. Ground. 0 volt. Ground. 0 volt. Bias. See Figure 10 for the recommended bias circuit. Description
2
GND VDD NC NC NC VDD IC FS2 FS1 C19oEN GND C19i VDD GND NC GND Zarlink Semiconductor Inc.
Data Sheet
Pin Description Table (continued) Pin # 12 Name OC-CLKoEN Description
ZL30406
SONET/SDH Clock Enable (CMOS Input). If tied high this control pin enables the OC-CLKoP/N differential driver. Pulling this input low disables the output clock without deactivating differential drivers. C77 Clock Output Enable A (CMOS Input). If tied high this control pin enables the C77oP/N-A output clock. Pulling this input low disables the output clock without deactivating differential drivers. C77 Clock Output Enable B (CMOS Input). If tied high this control pin enables the C77oP/N-B output clock. Pulling this input low disables the output clock without deactivating differential drivers. C77 Clock Output Enable C (CMOS Input). If tied high this control pin enables the C77oP/N-C output clock. Pulling this input low disables the output clock without deactivating differential drivers. C77 Clock Output Enable D (CMOS Input). If tied high this control pin enables the C77oP/N-D output clock. Pulling this input low disables the output clock without deactivating differential drivers. Ground. 0 volt. Positive Digital Power Supply. +3.3V 10% No internal bonding Connection. Leave unconnected. No internal bonding Connection. Leave unconnected. No internal bonding Connection. Leave unconnected. Positive Digital Power Supply. +3.3V 10% Internal Connection. Connect this pin to Ground (GND). Frequency Select 2-1 (CMOS Input). These inputs program the clock frequency on the OC-CLKo output. The possible output frequencies are 19.44 MHz (00), 38.88 MHz (01), 77.76 MHz (10), 155.52 MHz (11). C19o Output Enable (CMOS Input). If tied high this control pin enables the C19o output clock. Pulling this pin low forces output driver into a high impedance state. Ground. 0 volt. C19 Reference Input (CMOS Input). This pin is a single-ended input reference source used for synchronization. This pin accepts 19.44 MHz. Positive Digital Power Supply. +3.3V 10% Ground. 0 volt. No internal bonding Connection. Leave unconnected. Ground. 0 volt. Ground. 0 volt Positive Digital Power Supply. +3.3V 10% C19 Clock Output (CMOS Output). This pin provides a single-ended CMOS clock at 19.44 MHz.
C77oEN-A 13 C77oEN-B 14 C77oEN-C 15 C77oEN-D 16 17 18 19 20 21 22 23 24 25 26 GND VDD NC NC NC VDD IC FS2 FS1 C19oEN
27 28 29 30 31 32 33 34 35
GND C19i VDD GND NC GND GND VDD C19o
Zarlink Semiconductor Inc.
3
ZL30406
Pin Description Table (continued) Pin # 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 Name GND NC GND GND NC GND VDD GND VCC GND VDD VCC GND VCC C77oN-D C77oP-D GND VCC C77oP-C C77oN-C GND VCC C77oN-B C77oP-B GND VCC C77oP-A C77oN-A GND EP_GND Ground. 0 volt. No internal bonding Connection. Leave unconnected. Ground. 0 volt. Ground. 0 volt. No internal bonding Connection. Leave unconnected. Ground. 0 volt. Positive Digital Power Supply. +3.3V 10% Ground. 0 volt. Positive Analog Power Supply. +3.3V 10% Ground. 0 volt. Positive Digital Power Supply. +3.3V 10% Positive Analog Power Supply. +3.3V 10% Ground. 0 volt. Positive Analog Power Supply. +3.3V 10%. Description
Data Sheet
C77 Clock Output (LVPECL Output). These outputs provide a differential LVPECL clock at 77.76 MHz. Unused LVPECL port should be left unterminated to decrease supply current. Ground. 0 volt. Positive Analog Power Supply. +3.3V 10%. C77 Clock Output (LVPECL Output). These outputs provide a differential LVPECL clock at 77.76 MHz. Unused LVPECL port should be left unterminated to decrease supply current. Ground. 0 volt. Positive Analog Power Supply. +3.3V 10%. C77 Clock Output (LVPECL Output). These outputs provide a differential LVPECL clock at 77.76 MHz. Unused LVPECL port should be left unterminated to decrease supply current. Ground. 0 volt. Positive Analog Power Supply. +3.3V 10%. C77 Clock Output (LVPECL Output). These outputs provide a differential LVPECL clock at 77.76 MHz. Unused LVPECL port should be left unterminated to decrease supply current. Ground. 0 volt. Exposed die Pad Ground. 0 volt (connect to GND)
4
Zarlink Semiconductor Inc.
Data Sheet 1.0 Functional Description
ZL30406
The ZL30406 is an analog phased-locked loop which provides rate conversion and jitter attenuation for SONET/SDH OC-48/STM-16, OC-12/STM-4 and OC-3/STM-1 applications. A functional block diagram of the ZL30406 is shown in Figure 1 and a brief description is presented in the following sections.
1.1
Frequency/Phase Detector
The Frequency/Phase Detector compares the frequency/phase of the input reference signal with the feedback signal from the Frequency Divider circuit and provides an error signal corresponding to the frequency/phase difference between the two. This error signal is passed to the Loop Filter circuit and averaged to control the VCO frequency.
1.2
Loop Filter
The Loop Filter is a low pass filter. This low pass filter ensures that the network jitter requirements are met for an input reference frequency of 19.44 MHz. The corner frequency of the Loop Filter is configurable with an external capacitor and resistor connected to the LPF pin and ground as shown below.
ZL30406
LPF Internal Loop Filter RF CF
RF=8.2 k, CF=470 nF (for 14 kHz PLL bandwidth)
Figure 3 - External Loop Filter
1.3
VCO
The voltage-controlled oscillator (VCO) receives the filtered error signal from the Loop Filter, and based on the voltage of the error signal, generates a primary frequency. The VCO output is connected to the Output Interface Circuit that divides VCO frequency and buffers generated clocks.
Zarlink Semiconductor Inc.
5
ZL30406
1.4 Output Interface Circuit
Data Sheet
The output of the VCO is used by the Output Interface Circuit to provide four LVPECL differential clocks at 77.76 MHz, one programmable CML differential clock (19.44 MHz, 38.88 MHz, 77.76 MHz, 155.52 MHz) controlled with FS1-2 pins and a single-ended 19.44 MHz output clock. This block provides also a 19.44MHz feedback clock that closes PLL loop. Each output clock can be enabled or disabled individually with the associated Output Enable pin. Output Clocks C77oP/N-A C77oP/N-B C77oP/N-C C77oP/N-D OC-CLKoP/N C19o Output Enable Pins C77oEN-A C77oEN-B C77oEN-C C77oEN-D OC-CLKoEN C19oEN
Table 1 - Output Enable Control To reduce power consumption and achieve the lowest possible intrinsic jitter the unused output clocks must be disabled. If any of the LVPECL outputs are disabled they must be left open without any terminations. The output clock frequency of the OC-CLKo CML differential output clock is selected with FS1-2 pins as shown in the following table. FS2 0 0 1 1 FS1 0 1 0 1 OC-CLKo Frequency 19.44 MHz 38.88 MHz 77.76 MHz 155.52 MHz
Table 2 - OC-CLKo Clock Frequency Selection
6
Zarlink Semiconductor Inc.
Data Sheet 2.0
2.1
ZL30406
Applications
Ultra-low jitter SONET/SDH equipment clocks
The ZL30406 functionality and performance complements the entire family of the Zarlink's advanced network synchronization PLLs. Its superior jitter filtering characteristics exceed requirements of SONET/SDH optical interfaces operating at OC-48/STM-16 rate (2.5Gbit/s). The ZL30406 in combination with the MT90401 or the ZL30407 (SONET/SDH Network Element PLLs) provides the core building blocks for high quality equipment clocks suitable for network synchronization (see Figure 4).
C19i
ZL30406
OC-CLKo C77oA C77oB C77oC C77oD C19o
C77oEN-D
CML LVPECL LVPECL LVPECL LVPECL CMOS
LPF
OC-CLKoEN C77oEN-B C19oEN
RF CF
155.52 MHz, 77.76 MHz 38.88 MHz, 19.44 MHz 77.76 MHz 77.76 MHz 77.76 MHz 77.76 MHz 19.44 MHz
C77oEN-C
C77oEN-A
PRI SEC Synchronization Reference Clocks RefSel RefAlign PRIOR SECOR LOCK HOLDOVER
MT90401 or ZL30407
C19o C155o C34o/C44o C16o C8o C6o C4o C2o C1.5o F16o F8o F0o
CMOS LVDS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS
19.44 MHz 155.52 MHz 34.368 MHz or 44.736 MHz 16.384 MHz 8.192 MHz 6.312 MHz 4.096 MHz 2.048 MHz 1.544 MHz 8 kHz 8 kHz 8 kHz
C20i
R/W A0 - A6
20 MHz OCXO
D0 - D7
DS CS
Data Port
uP
Controller Port
Note: Only main functional connections are shown
Figure 4 - SONET/SDH Equipment Timing Card
Zarlink Semiconductor Inc.
7
ZL30406
Data Sheet
The ZL30406 in combination with the MT9046 provides an optimum solution for SONET/SDH line cards (see Figure 5).
C19i
ZL30406
LPF
C77oEN-C C77oEN-A
OC-CLKo C77oA C77oB C77oC C77oD C19o
CML LVPECL LVPECL LVPECL LVPECL CMOS
155.52 MHz, 77.76 MHz 38.88 MHz, 19.44 MHz 77.76 MHz 77.76 MHz 77.76 MHz 77.76 MHz 19.44 MHz
C1
C2
C19oEN
R1
C77oEN-D
C77oEN-B
R1 = 680 C1 = 820 nF C2 = 22 nF
OC-CLKoEN
PRI SEC Synchronization Reference Clocks RSEL
MT9046
LOCK HOLDOVER C20i 20 MHz TCXO
MS1 MS2 FS1 FS2
C19o C16o C8o C6o C4o C2o C1.5o F16o F8o F0o
CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS
19.44 MHz 16.384 MHz 8.192 MHz 6.312 MHz 4.096 MHz 2.048 MHz 1.544 MHz 8 kHz 8 kHz 8 kHz
FLOCK PCCi TCLR
uC
Hardware Control
Note: Only main functional connections are shown
Figure 5 - SONET/SDH Line Card
8
Zarlink Semiconductor Inc.
Data Sheet
2.2 2.2.1 Recommended Interface circuit LVPECL to LVPECL Interface
ZL30406
The C77oP/N-A, C77oP/N-B, C77oP/N-B, and C77oP/N-D outputs provide differential LVPECL clocks at 77.76 MHz. The LVPECL output drivers require a 50 termination connected to the VCC-2V source for each output terminal at the terminating end as shown below. The terminating resistors should be placed as close as possible to the LVPECL receiver.
+3.3V
0.1uF ZL30406 VCC VCC=+3.3V R1 R1 LVPECL Receiver
LVPECL Driver
C77oP-A
Z=50
Z=50 C77oN-A R2 GND R2
Typical resistor values: R1 = 130, R2 =82
Figure 6 - LVPECL to LVPECL Interface
2.2.2
CML to CML Interface
The CMLP/N output provides a differential CML/LVDS compatible clock at 19.44 MHz, 38.88 MHz, 77.76 MHz, 155.52 MHz selected with FS1-2 pins. The output drivers require a 50 load at the terminating end if the receiver is CML type.
+3.3V Low Impedance DC bias source CML Receiver
ZL30406
VCC
0.1uF
CML Driver
OC-CLKoP
0.1uF
Z=50 Z=50
50
50
OC-CLKoN
0.1uF
GND
Figure 7 - CML to CML Interface
Zarlink Semiconductor Inc.
9
ZL30406
2.2.3 CML to LVDS Interface
Data Sheet
To configure the driver as an LVDS driver, external biasing resistors are required to set up the common mode voltage as specified by ANSI/TIA/EIA-644 LVDS standard. The standard specifies the VCM (common mode voltage) as minimum 1.125V, typical 1.2V, and maximum 1.375V. The following figure provides a recommendation for LVDS applications.
+3.3V
0.1uF ZL30406 VCC 10nF
VCC=+3.3V R1 R1 LVDS Receiver
CML Driver
OC-CLKoP
Z=50 Z=50
100
OC-CLKoN
10nF R2 R2
GND
Typical resistor values: R1 = 16k, R2 = 10k
Figure 8 - LVDS Termination
2.2.4
CML to LVPECL Interface
In the case when more than four 77.76 MHz clocks are required to drive LVPECL receivers then the unused OCCLKo clock (CML output) can be configured to output the 77.76MHz clock and interface to the LVPECL receiver as is shown in the Figure 9. The terminating resistors should be placed as close as possible to the LVPECL receiver.
+3.3V
VCC
0.1uF ZL30406 10nF VCC=+3.3V R1 R1 LVPECL Receiver
CML Driver
OC-CLKoP 77.76MHz OC-CLKoN
Z=50 Z=50
10nF R2 GND R2
Typical resistor values: R1 = 82, R2 =130
Figure 9 - CML to LVPECL Interface
10
Zarlink Semiconductor Inc.
Data Sheet
2.3 Power supply and BIAS circuit filtering recommendations
ZL30406
Figure 10 presents a complete filtering arrangement that is recommended for applications requiring maximum jitter performance. The level of required filtering is subject to further optimization and simplification. Please check Zarlink's web site for updates.
0.1uF +3.3V Power Rail GND GND VCC
0.1uF GND VCC
0.1uF GND VCC
0.1uF VCC
0.1uF
Ferrite Bead + 0.1uF 10uF 0.1uF
4.7 + 33uF
GND 64 VCC1 2 VCC 0.1uF VCC2 + 33uF 0.1uF BIAS + 33uF 0.1uF 4 6 GND 8 GND 10GND 11 12 14 16 18
0.1uF 62 60 58 56 54 52 50 48 GND VCC VDD VCC VDD
ZL30406
220
46 GND 44 GND 42 GND 40 GND GND38 GND36 34
0.1uF 0.1uF 0.1uF
VDD GND 0.1uF
20
22 VDD
24
26 GND
28 VDD
30 GND
32 GND 0.1uF
GND VDD
0.1uF
0.1uF
Notes: 1. All the ground pins (GND) and the Exposed die Pad (metal area at the back of the package) are connected to the same 2. Select Ferrite Bead with IDC > 400mA and RDC in a range from 0.10 to 0.15
Figure 10 - Power Supply and BIAS circuit filtering
Zarlink Semiconductor Inc.
11
ZL30406
3.0 Characteristics
Characteristics 1 2 3 4 5 6 Supply voltage Voltage on any pin Current on any pin ESD Rating Storage temperature Package power dissipation Sym VDDR, VCCR VPIN IPIN VESD TST PPD -55 Min TBD -0.5 -0.5 Max TBD VCC + 0.5 VDD + 0.5 30 1500 125 1.8
Data Sheet
Absolute Maximum Ratings Units V V mA V C W
Voltages are with respect to ground unless otherwise stated. Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied.
Recommended Operating Conditions Characteristics 1 2 Operating Temperature Positive Supply Sym TOP VDD, VCC VCC_VCO Min -40 3.0 Typ 25 3.3 Max +85 3.6 Units C V Notes
Voltages are with respect to ground unless otherwise stated. Typical figures are for design aid only: not guaranteed and not subject to production testing.
DC Electrical Characteristics Characteristics 1 Supply Current Sym IDD+ICC Min Typ 140 Max 155 Units mA Notes LVPECL, CML drivers disabled and unterminated Note 1,2
2
Incremental Supply Current to single LVPECL driver (driver enabled and terminated, see Figure 6) Incremental Supply Current to CML driver (driver enabled and terminated, see Figure 7) CMOS: High-level input voltage CMOS: Low-level input voltage CMOS: Input leakage current, C19i
ILVPECL
40
mA
3
ICML
24
mA
Note 3
4 5 6
VIH VIL IIL
0.7VDD 0 1
VDD 0.3VDD
V V uA VI = VDD or 0V
12
Zarlink Semiconductor Inc.
Data Sheet
DC Electrical Characteristics (continued) Characteristics 7 CMOS: Input bias current for pulled-down inputs: FS1, FS2, C77oEN-A, C77oEN-C, C77oEN-D, OC-CLKoEN CMOS: Input bias current for pulled-up inputs: , C77oEN-B, C19o_EN CMOS: High-level output voltage CMOS: Low-level output voltage CMOS: C19o output rise time (18pF) CMOS: C19o output fall time (18pF) LVPECL: Differential output voltage LVPECL: Offset voltage LVPECL: Output rise/fall times CML: Differential output voltage CML: Offset voltage (Also referred to as common mode voltage) CML: Output rise/fall times Sym IB-PU Min Typ 300 Max Units uA
ZL30406
Notes VI = VDD
8
IB-PD
90
uA
VI = 0V
9 10 11 12 13 14 15 16 17
VOH VOL TR TF IVOD_LVPECLI VOS_LVPECL TRF IVOD_CMLI VOS_CML
2.4 0.4 1.8 1.1 1.30 Vcc1.38 Vcc1.27 260 0.70 Vcc0.58 Vcc0.54 120 Vcc0.50 Vcc1.15 3.3 1.4
V V ns ns V V ps V V
IOH = 8 mA IOL = 4 mA 18 pF load 18 pF load Note 2 Note 2 Note 2 Note 3 Note 3
18
TRF
ps
Note 3
: Voltages are with respect to ground unless otherwise stated. :Typical figures are for design aid only: not guaranteed and not subject to production testing. Note: Supply voltage and operating temperature are as per Recommended Operating Conditions Note 1: The ILVPECL current is determined by termination network connected to LVPECL outputs. More than 25% of this current flows outside the chip and it does not contribute to the internal power dissipation. Note 2: Note 3: LVPECL outputs terminated with ZT = 50 resistors biased to VCC-2V (see Figure 6) CML outputs terminated with ZT = 50 resistors connected to low impedance DC bias voltage source (see Figure 7)
Zarlink Semiconductor Inc.
13
ZL30406
AC Electrical Characteristics - Output Timing Parameters Measurement Voltage Levels Characteristics 1 Threshold Voltage Sym VT-CMOS VT-LVPECL VT-CML VHM VLM CMOS 0.5VDD LVPECL 0.5VOD_LVPECL CML
Data Sheet
Units V
0.5VOD_CML
2 3
Rise and Fall Threshold Voltage High Rise and Fall Threshold Voltage Low
0.7VDD 0.3VDD
0.8VOD_LVPECL 0.2VOD_LVPECL
0.8VOD_CML 0.2VOD_CML
V V
Timing Reference Points
All Signals t IF, tOF tIR, t OR
V HM VT VLM
Figure 11 - Output Timing Parameter Measurement Voltage Levels AC Electrical Characteristics - C19i Input to C19o and C77o Output Timing Characteristics 1 2 C19i to C19o delay C19i to C77oA delay Sym tC19D tC77D Min Typ 6.7 -4 Max Units ns ns Notes
Supply voltage and operating temperature are as per Recommended Operating Conditions. Typical figures are for design aid only: not guaranteed and not subject to production testing.
C19i (19.44 MHz) C19o (19.44 MHz) tC77D C77oA (77.76 MHz) t C19D
V T-CMOS
VT-CMOS
V T-LVPECL
Note: All output clocks have nominal 50% duty cycle.
Figure 12 - C19i Input to C19o and C77o Output Timing
14
Zarlink Semiconductor Inc.
Data Sheet
AC Electrical Characteristics - C19i Input to OC-CLKo Output Delay Timing (CML) Characteristics 1 2 3 4 C19i to OC-CLKo(19) delay C19i to OC-CLKo(38) delay C19i to OC-CLKo(77) delay C19i to OC-CLKo(155) delay Sym tOC-CLK19D tOC-CLK38D tOC-CLK77D tOC-CLK155D Min Typ 3.2 3.0 2.7 2.4 Max Units ns ns ns ns
ZL30406
Notes
Supply voltage and operating temperature are as per Recommended Operating Conditions. Typical figures are for design aid only: not guaranteed and not subject to production testing.
C19i (19.44 MHz) tOC-CLK19D OC-CLKo(19) (19.44 MHz) tOC-CLK38D OC-CLKo(38) (38.88 MHz) tOC-CLK77D OC-CLKo(77) (77.76 MHz) tOC-CLK155D OC-CLKo(155) (155.52 MHz)
VT-CMOS
VT-CML
VT-CML
VT-CML
V T-CML
Note: All output clocks have nominal 50% duty cycle.
Figure 13 - C19i Input to OC-CLKo Output Timing
Zarlink Semiconductor Inc.
15
ZL30406
AC Electrical Characteristics- C77 Clocks Output Timing Characteristics 1 2 3 C77oA to C77oB C77oA to C77oC C77oA to C77oD Sym tC77D-AB tC77D-AC tC77D-AD Min Typ 100 100 100 Max Units ps ps ps
Data Sheet
Notes
Supply voltage and operating temperature are as per Recommended Operating Conditions. Typical figures are for design aid only: not guaranteed and not subject to production testing.
C77oA t C77D-AB C77oB t C77D-AC C77oC
V T-LVPECL
V T-LVPECL
V T-LVPECL
tC77D-AD C77oD VT-LVPECL
Note: All output clocks have nominal 50% duty cycle.
Figure 14 - C77oB, C77oC, C77oD Outputs Timing
16
Zarlink Semiconductor Inc.
Data Sheet
Performance Characteristics - Functional- (VCC = 3.3V 10%; TA = -40 to 85C) Characteristics 1 2 Pull-in range Lock Time Min 1000 300 Max Units ppm ms Notes
ZL30406
Performance Characteristics: Output Jitter Generation - GR-253-CORE conformance - (VCC = 3.3V 10%; TA = 40 to 85C)
GR-253-CORE Jitter Generation Requirements Interface (Category II) 1 2 OC-48 STS-48 OC-12 STS-12 Jitter Measurement Filter 12kHz - 20MHz 12kHz - 5MHz Limit in UI 0.1 UIpp 0.01UIRMS 0.1 UIpp 0.01UIRMS
ZL30406 Jitter Generation Performance Equivalent limit in time domain 40.2 4.02 161 16.1 TYP 1.3 0.7 MAX 16.9 2.1 9.0 1.3 Units psP-P psRMS psP-P psRMS
Typical figures are for design aid only: not guaranteed and not subject to production testing. Loop Filter components: RF=8.2 k, CF=470 nF
Performance Characteristics: Output Jitter Generation - ETSI EN 300 462-7-1 conformance - (VCC = 3.3V 10%;
TA = -40 to 85C)
EN 300 462-7-1 Jitter Generation Requirements Interface 1 STM-16 Jitter Measurement Filter 1MHz to 20MHz 5kHz to 20MHz 2 STM-4 250kHz to 5MHz Limit in UI 0.1 UIpp 0.5UIpp 0.1 UIpp 0.5 UIpp 1kHz to 5MHz -
ZL30406 Jitter Generation Performance Equivalent limit in time domain 40.2 201 161 804 TYP 1.0 1.3 0.46 2.4 MAX 12.6 1.5 17.1 2.2 5.8 0.9 29.8 3.2 Units psP-P psRMS psP-P psRMS psP-P psRMS psP-P psRMS
Typical figures are for design aid only: not guaranteed and not subject to production testing. Loop Filter components: RF=8.2 k, CF=470 nF
Zarlink Semiconductor Inc.
17
ZL30406
Data Sheet
Performance Characteristics: Output Jitter Generation - G.813 conformance (Option 1 and 2) - (VCC = 3.3V
10%; TA = -40 to 85C)
G.813 Jitter Generation Requirements Interface Jitter Measurement Filter Option 1 1 STM-16 1MHz to 20MHz 0.1 UIpp 0.5 UIpp 5kHz to 20MHz 2 STM-4 250kHz to 5MHz 1kHz to 5MHz Option 2 3 4 STM-16 12kHz - 20MHz STM-4 12kHz - 5MHz 0.1 UIpp 0.1 UIpp 0.1 UIpp 0.5 UIpp Limit in UI
ZL30406 Jitter Generation Performance
Equivalent limit in time domain
TYP
MAX
Units
40.2 201 161 804 40.2 161 -
1.0 1.3 0.46 2.4 1.3 0.7
12.6 1.5 17.1 2.2 5.8 0.9 29.8 3.2 16.9 2.1 9.0 1.3
psP-P psRMS psP-P psRMS psP-P psRMS psP-P psRMS psP-P psRMS psP-P psRMS
Typical figures are for design aid only: not guaranteed and not subject to production testing. Loop Filter components: RF=8.2 k, CF=470 nF
18
Zarlink Semiconductor Inc.
c Zarlink Semiconductor 2002 All rights reserved.
Package Code Previous package codes
ISSUE ACN DATE APPRD.
For more information about all Zarlink products visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request.
Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in an I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2003, Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE


▲Up To Search▲   

 
Price & Availability of ZL30406

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X