Part Number Hot Search : 
HMS20 SMBJ10 C1006 A5801038 00N04 09FXM0 PIC7505 TMP86
Product Description
Full Text Search
 

To Download PDI1394L41 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 INTEGRATED CIRCUITS
SEE THE LAST 2 PAGES OF THIS DATASHEET FOR A LIST OF ERRATA RELATED TO THIS PART.
NOTICE: DTLA SENSITIVE INFORMATION HAS BEEN WITHHELD FROM THIS DATA SHEET. SEE SECTION 2.1 FOR DETAILS.
PDI1394L41 1394 content protection AV link layer controller
Preliminary specification Supersedes data of 2000 Apr 15 2000 Dec 01
Philips Semiconductors
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
1.0 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 Use restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 QUICK REFERENCE DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0 ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 PIN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0 FUNCTIONAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0 INTERNAL BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.0 APPLICATION DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0 PIN DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 Host Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 AV Interface 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 AV Interface 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4 Phy Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.5 Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.0 RECOMMENDED OPERATING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.0 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.0 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2 AV interface and AV layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2.1 IEC 61883 International Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2.2 CIP Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2.3 The AV Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2.4 Content Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2.5 Audio Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2.6 SY - Sync Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.2.7 Programmable Buffer Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.3 Bushold and Link/PHY single capacitor galvanic isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.3.1 Bushold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.3.2 Single capacitor isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.4 Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5 The host interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.1 Read accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.2 Write accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.3 Accessing the RDI register (Power-down, Power-up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.4 Big and little endianness, data invariance, and data bus width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.5 Accessing the asynchronous packet queues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5.6 The CPU bus interface signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 The Asynchronous Packet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6.1 Reading an Asynchronous Packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6.2 Link Packet Data Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.7 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.0 REGISTER MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1 Link Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.1 ID Register (IDREG) - Base Address: 0x000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.2 General Link Control (LNKCTL) - Base Address: 0x004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.3 Link /Phy Interrupt Acknowledge (LNKPHYINTACK) - Base Address: 0x008 . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.4 Link / Phy Interrupt Enable (LNKPHYINTE) - Base Address: 0x00C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.5 Cycle Timer Register (CYCTM) - Base Address: 0x010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.6 Phy Register Access (PHYACS) - Base Address: 0x014 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.7 Global Interrupt Status and TX Control (GLOBCSR) - Base Address: 0x018 . . . . . . . . . . . . . . . . . . . . . . . . . 13.1.8 Timer (TIMER) - Base Address: 0x01C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2 AV (Isochronous) Transmitter and Receiver Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2.1 Isochronous Transmit Packing Control and Status (ITXPKCTL) - Base Address: 0x020 . . . . . . . . . . . . . . .
1 1 1 1 1 2 3 3 4 4 4 5 6 7 7 8 8 9 9 9 9 9 9 10 11 11 11 12 12 13 13 14 14 15 16 17 18 19 27 27 27 41 42 47 47 47 49 50 50 51 51 52 53 53
2000 Dec 01
i
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.2.2 Common Isochronous Transmit Packet Header Quadlet 1 (ITXHQ1) - Base Address: 0x024 . . . . . . . . . . . 13.2.3 Common Isochronous Transmit Packet Header Quadlet 2 (ITXHQ2) - Base Address: 0x028 . . . . . . . . . . . 13.2.4 Isochronous Transmitter Interrupt Acknowledge (ITXINTACK) - Base Address: 0x02C . . . . . . . . . . . . . . . . 13.2.5 Isochronous Transmitter Interrupt Enable (ITXINTE) - Base Address: 0x030 . . . . . . . . . . . . . . . . . . . . . . . . . 13.2.6 Isochronous Transmitter Control Register (ITXCTL) - Base Address: 0x34 . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2.7 Isochronous Transmitter Memory Status (ITXMEM) - Base Address: 0x038 . . . . . . . . . . . . . . . . . . . . . . . . . 13.2.8 Isochronous Receiver Unpacking Control (IRXPKCTL) - Base Address: 0x040 . . . . . . . . . . . . . . . . . . . . . . 13.2.9 Common Isochronous Receiver Packet Header Quadlet 1 (IRXHQ1) - Base Address: 0x044 . . . . . . . . . . 13.2.10 Common Isochronous Receiver Packet Header Quadlet 2 (IRXHQ2) - Base Address: 0x048 . . . . . . . . . 13.2.11 Isochronous Receiver Interrupt Acknowledge (IRXINTACK) - Base Address: 0x04C . . . . . . . . . . . . . . . . . 13.2.12 Isochronous Receiver Interrupt Enable (IRXINTE) - Base Address: 0x050 . . . . . . . . . . . . . . . . . . . . . . . . . 13.2.13 Isochronous Receiver Control Register (IRXCTL) - Base Address: 0x054 . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2.14 Isochronous Receiver Memory Status (IRXMEM) - Base Address: 0x058 . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3 Asynchronous Control and Status Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.1 Asynchronous RX/TX Control (ASYCTL) - Base Address: 0x080 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.2 Asynchronous RX/TX Memory Status (ASYMEM) - Base Address: 0x084 . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.3 Asynchronous Transmit Request Next (TX_RQ_NEXT) - Base Address: 0x088 . . . . . . . . . . . . . . . . . . . . . . 13.3.4 Asynchronous Transmit Request Last (TX_RQ_LAST) - Base Address: 0x08C . . . . . . . . . . . . . . . . . . . . . . 13.3.5 Asynchronous Transmit Response Next (TX_RP_NEXT) - Base Address: 0x090 . . . . . . . . . . . . . . . . . . . . . 13.3.6 Asynchronous Transmit Response Last (TX_RP_LAST) - Base Address: 0x094 . . . . . . . . . . . . . . . . . . . . . 13.3.7 Asynchronous Receive Request (RREQ) - Base Address: 0x098 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.8 Asynchronous Receive Response (RRSP) - Base Address: 0x09C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.9 Asynchronous RX/TX Interrupt Acknowledge (ASYINTACK) - Base Address: 0x0A0 . . . . . . . . . . . . . . . . . . 13.3.10 Asynchronous RX/TX Interrupt Enable (ASYINTE) - Base Address: 0x0A4 . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.11 RDI Register - Base Address: 0x0B0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3.12 Shadow Register (SHADOW_REG) - Base Address: 0x0F4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4 Indirect Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.1 ........................................................................................... 13.4.2 Indirect Address Register (INDADDR) - Base Address: 0x0F8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3 Indirect Data Register (INDDATA) - Base Address: 0x0FC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5 Indirect Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5.1 Registers for FIFO Size Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.0 DC ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1 Pin Categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.0 AC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.0 TIMING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.1 AV Interface Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.2 AV Interface Critical Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.3 PHY-Link Interface Critical Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.4 Host Interface Critical Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 CYCLEIN/CYCLEOUT Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.6 RESET Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54 54 55 55 56 56 57 58 58 59 59 60 61 62 62 62 63 63 63 63 64 64 64 65 65 66 67 67 67 67 68 68 71 71 72 73 73 73 74 75 76 76
2000 Dec 01
ii
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
1.0 FEATURES
* IEEE1394.a and IEEE1394-1995 Standard Link Layer Controller * Hardware Support for the IEC61883 International Standard of
Digital Interface for Consumer Electronics
2.0 DESCRIPTION
The PDI1394L41, Philips Semiconductors Full Duplex 1394 Audio/Video (AV) Link Layer Controller, is an IEEE 1394-1995 compliant link layer controller featuring 2 embedded AV layer interfaces. The AV layers are designed to encrypt and pack, or unpack and decrypt application data packets for transmission over the IEEE1394 bus using isochronous data transfers and the "5C" content protection method. The application data is packetized according to the IEC 61883 International Standard of Interface for Consumer Electronic Audio/Video Equipment. Both AV layer interfaces are byte-wide ports capable of accommodating various MPEG-2 and DVC codecs. A flexible host interface is provided for internal register configuration as well as performing asynchronous data transfers. Both 8 bit and 16 bit wide data paths, as well as multiplexed/non-multiplexed access modes are supported. The PDI1394L41 is powered by a single 3.3 V power supply and the inputs and outputs are 5 V tolerant. It is available in the LQFP144 package.
* Interface to any IEEE 1394-1995 or 1394.a Physical Layer
Interface
* 5 V Tolerant I/Os * Single 3.3 V supply voltage * Full-duplex isochronous operation * Operates with 400/200/100 Mbps physical layer devices * 12K byte fully programmable FIFO pool for isochronous and
asynchronous data
* Supports single capacitor isolation mode and IEEE 1394-1995,
Annex J. isolation
* 6-field deep SYT buffer added to enhance real-time isochronous
synchronization using the AVFSYNC pin
2.1 Use restrictions
Due to rules set forth by the Digital Transmission Licensing Administrator (DTLA) information concerning some features of the L41 is the subject of a license issued by the DTLA. That information has been omitted from this data sheet and is available only to DTLA licensees on a restricted distribution basis. In order to obtain a copy of the information, licensed parties should contact Philips Semiconductors at 1394@philips.com and request data sheet addendum AL41-1. Upon verification of the requestor's DTLA license status, a paper copy of the addendum will be sent to the DTLA listed responsible person within the requesting company. Distribution of samples and sales of the L41 chip are likewise restricted to DTLA licensees. For information pertaining to the procurement of a DTLA license please consult the DTLA website at http://www.dtcp.com.
* Generates its own AV port clocks under software control. Select
one of three frequencies: 24.576, 12.288, or 6.144 MHz
* Hardware support for the "5C" content protection method * On chip timer resources * Flexible 8/16 bit multiplexed/non-multiplexed host interface * Parallel AV interface * Fast 56-bit M6 cipher/decipher blocks capable of operating up to
100 Mbps
* Hardware authentication acceleration to reduce software
processor loading
3.0 QUICK REFERENCE DATA
GND = 0 V; Tamb = 25 C SYMBOL VDD IDD SCLK PARAMETER Functional supply voltage range Supply current @ VDD = 3.3 V Device clock Operating 49.147 CONDITIONS MIN 3.0 TYP 3.3 110 49.152 MAX 3.6 200 49.157 UNIT V mA MHz
4.0 ORDERING INFORMATION
PACKAGES 144-pin LQFP144 TEMPERATURE RANGE 0 C to +70 C OUTSIDE NORTH AMERICA PDI1394L41BE NORTH AMERICA PDI1394L41BE PKG. DWG. # SOT486-1
NOTE: This datasheet is subject to change. Please visit our internet website www.semiconductors.philips.com/1394 for latest changes.
2000 Dec 01
1
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
5.0 PIN CONFIGURATION
144 109
1
108
LQFP
36
73
37 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Function HIF D15 HIF D14 HIF D13 HIF D12 GND VDD HIF D11 HIF D10 HIF D9 HIF D8 GND VDD HIF AD7 HIF AD6 HIF AD5 HIF AD4 GND VDD HIF AD3 HIF AD2 HIF AD1 HIF AD0 GND VDD HIF A8 HIF A7 HIF A6 HIF A5 HIF A4 HIF A3 HIF A2 HIF A1 HIF A0 GND VDD HIF CSN Pin 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 Function HIF WRN HIF INTN HIF ALE HIF RDN HIF WAIT RESETN GND VDD HIF 16BIT HIF MUX 1394 MODE PD RESERVED RESERVED RESERVED RESERVED GND VDD CLK50 CYCLEIN CYCLEOUT RESERVED RESERVED GND VDD TESTPIN TESTPIN TESTPIN RESERVED RESERVED RESERVED RESERVED GND VDD RESERVED RESERVED Pin 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108
72 Function PHY D7* PHY D6* PHY D5* PHY D4* GND VDD PHY D3* PHY D2* PHY D1* PHY D0* GND VDD PHY CTL1* PHY CTL0* LREQ SCLK* GND VDD LPS* LINKON ISON GND VDD AV1ERR0 AV1ERR1 AV1ENDPCK AV1CLK AV1FSYNC AV1 SY AV1VALID AV1SYNC AV1EMIO AV1EMI1 GND VDD AV1D0 Pin 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 Function AV1D1 AV1D2 AV1D3 GND VDD AV1D4 AV1D5 AV1D6 AV1D7 AV1READY GND VDD AV2ERR0/LTLEND AV2ERR1/DATINV AV2ENDPCK AV2CLK AV2FSYNC AV2 SY AV2VALID AV2SYNC AV2EMI0 AV2EMI1 GND VDD AV2D0 AV2D1 AV2D2 AV2D3 GND VDD AV2D4 AV2D5 AV2D6 AV2D7 AV2READY RESERVED
*
Indicates pin equipped with internal bus hold circuit activated by the state of the ISON pin.
SV01020
2000 Dec 01
2
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
6.0 FUNCTIONAL DIAGRAM
HIF A[7:0] HIF D[15:8] HIF AD[7:0] HIF A8 HIF WRN HIF RDN HIF CSN HIF 16BIT HIF MUX RESETN HIF ALE HIF WAIT HIF INTN PD CYCLEIN CYCLEOUT CLK50 AV1 D[7:0] AV1CLK AV1VALID AV1SYNC AV1FSYNC AV1 SY AV1READY AV1EMI[1:0] AV1ENDPCK AV1ERR0 AV1ERR1 PHY D[0:7] PHY CTL[0:1] LPS LREQ ISON LinkOn SCLK 1394MODE
HOST
PHY
PDI1394L41 IEEE 1394 CONTENT PROTECTION AV LINK LAYER CONTROLLER
VDD GND
AV LAYER 1
AV2D[7:0] AV2CLK AV2VALID AV2SYNC AV2FSYNC AV2 SY AV2READY AV2EMI[1:0] AV2ENDPCK AV2ERR0/LTLEND AV2ERR1/DATAINV
AV LAYER 2
SV01021
7.0 INTERNAL BLOCK DIAGRAM
AV1 D[7:0] AV1READY AV1EMI[1:0] AV1CLK AV1SYNC AV1VALID AV1FSYNC AV1ENDPCK AV1ERR0 AV1ERR1 AV1SY
AV LAYER1
AV1 LAYER ISOCHRONOUS TRANSMITTER/ RECEIVER
CYCLEOUT LPS CYCLEIN PHY D[0:7] 12KB BUFFER MEMORY (ISOCH & ASYNC PACKETS) LINK CORE PHY CTL[0:1] LREQ LinkOn ISON PD SCLK 1394MODE
AV2 D[7:0] AV2READY AV2EMI[1:0] AV2CLK AV2SYNC AV2VALID AV2FSYNC AV2ENDPCK AV2ERR0/LTLEND AV2ERR1/DATAINV AV2SY
AV LAYER2
AV2 LAYER ISOCHRONOUS TRANSMITTER/ RECEIVER
NOTE: THERE IS ONE ISOCHRONOUS RECEIVER AND ONE ISOCHRONOUS TRANSMITTER--THEREFORE, WHEN EITHER AVPORT IS SET TO TRANSMIT, THE OTHER AVPORT IS AUTOMATICALLY SET TO RECEIVE ASYNC TRANSMITTER AND RECEIVER
HIF A[7:0] HIF A8 HIF D[15:8] HIF AD[7:0] HIF 16BIT HIF WRN HIF ALE HIF RDN HIF MUX HIF CSN HIF WAIT HIF INTN
HOST
8-BIT INTERFACE
CONTROL AND STATUS REGISTERS
RESETN
SV01022
2000 Dec 01
3
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
8.0 APPLICATION DIAGRAM
MPEG OR DVC DECODER AV INTERFACE PDI1394L41 AV LINK MPEG OR DVC DECODER AV INTERFACE
PHY-LINK INTERFACE
PDI1394Pxx PHY
1394 CABLE INTERFACE
DATA 16/ ADDRESS 9/ INTERRUPT & CONTROL
HOST CONTROLLER
SV01023
9.0 PIN DESCRIPTION 9.1 Host Interface
PIN No. 13, 14, 15, 16, 19, 20, 21, 22 1, 2, 3, 4, 7, 8, 9, 10 26, 27, 28, 29, 30, 31, 32, 33 25 36 PIN SYMBOL HIF AD[7:0] HIF D[15:8] HIF A[7:0] HIF A8 HIF CSN I/O I/O I/O I/O I I NAME AND FUNCTION Host Interface Data 7 (MSB) through 0. Byte wide data path to internal registers. Host Interface Data 15 (MSB) through 8. Only used in 16 bit access mode (HIF 16BIT = HIGH). Host Interface Address 0 through 8. Provides the host with a byte wide interface to internal registers. See description of Host Interface for addressing rules (Section 12.5). Control bit used to indicate the first byte/word of a read function or the last byte/word of a write function so that the data quadlet is fetched or stored. See Section 12.5 for more information regarding the host interface. Chip Select (active LOW). Host bus control signal to enable access to the FIFO and control and status registers. Write enable. When asserted (LOW) in conjunction with HIF CSN, a write to the PDI1394L41 internal registers is requested. (NOTE: HIF WRN and HIF RDN : if these are both LOW in conjunction with HIF CSN, then a write cycle takes place. This can be used to connect CPUs that use R/W_N line rather than separate RD_N and WR_N lines. In that case, connect the R/W_N line to the HIF WRN and tie HIF RDN LOW.) Interrupt (active LOW). Indicates a interrupt internal to the PDI1394L41. Read the General Interrupt Register for more information. This pin is open drain and requires a 1KW pull-up resistor. Address latch enable. Used in multiplex mode only. Read enable. When asserted (LOW) in conjunction with HIF CSN, a read of the PDI1394L41 internal registers is requested. Wait signal. Signals Host interface in WAIT condition when HI. See Section 12.5. Reset (active LOW). The asynchronous master reset to the PDI1394L41. Host interface mode pin. When LOW HIF operates in 8 bit mode. When HIGH HIF operates in 16 bit mode. Host interface mode pin. When LOW HIF operates in non-multiplex mode, when HIGH HIF operates in multiplex mode. When HIGH, the low-order eight address bits are multiplexed with data on HIF AD[7:0], otherwise they are non-multiplexed and supplied on A[7:0].
37
HIF WRN
I
38 39 40 41 42 45 46
HIF INTN HIF ALE HIF RDN HIF WAIT RESETN HIF 16BIT HIF MUX
O I I O I I I
2000 Dec 01
4
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
9.2 AV Interface 1
NOTE: This AV interface may be configured to transmit or receive according to the condition of "DIRAV1" bit in GLOBCSR register (0X018)--default is transmit. PIN No. 96 97 98 PIN SYMBOL AV1ERR0 AV1ERR1 AV1ENDPCK I/O O O I NAME AND FUNCTION CRC error. Indicates bus packet delivered on AV1 D[7:0] had a CRC error; the current AV packet is unreliable. Sequence Error. Indicates at least one source packet was lost before the current AV1 D [7:0] data. End of application packet indication from data source. Required only if input packet is not multiple of 4 bytes. It can be tied LOW for data packets that are 4*N in size. External application clock. Rising edge active. This pin can be programmed to be an output and the application clock. Depending on the configuration of AV Port 1 as transmitter or receiver, the output enable is located in the ITXPKCTL register (address 0x020) or IRXPKCTL register (address 0x040). Programmable frame sync, is set to input when AV interface 1 is a transmitter and to output when the interface is configured as a receiver. When the pin is an input, it is used to designate a frame of data for Digital Video (DV). The signal is time stamped and transmitted in the SYT field of ITXHQ2. When set to an output, the signal is derived from SYT field of IRXHQ2. SY Value. When port AV1 is configured as a transmitter, this pin is an input. When the AV port is configured to as a receiver, the pin is an output. See the description for bit 0 of the ITXCTL (0x034) and IRXCTL (0x054) registers. Indicates data on AV1 D [7:0] is valid. Indicates that the data currently being clocked by the source under the condition of AV1VALID is the start of an application packet. If the AV interface is configured as a receiver, then it will assert AV1SYNC when an application packet becomes available and persist until the first data of the packet is clocked out. Thus, AV1VALID may last for more than one cycle, but for exactly one cycle in which AV1VALID is asserted. Encryption Mode Indication pins. Outputs encryption mode when this AV port is in receive state with decipher enabled. Audio/Video Data 7 (MSB) through 1. Part of byte-wide interface to the AV layer 1. When the AV port is configured as a receiver, this pin is an input. This is a flow control signal that allows the application to indicate whether it is able to accept data flowing across AV Interface 1. The AV interface responds to an inactive AV1READY by not asserting AV1VALID, and thereby withholding data from the application. The AV1READY signal is processed through one level of pipelining, which means that the AV Link will accept data on the cycle in which AV1READY is de-asserted and will not accept data on the cycle in which AV1READY is asserted. 118 AV1READY When the AV port is configured to transmit, this pin is an output. This is a flow control signal that allows the link chip to indicate whether it is able to accept data flowing across AV Interface 1. The source of data, an external entity, responds to an inactive AV1READY by not asserting AV1VALID, and thereby withholding data. The AV1READY signal should be processed by the sink through one level of pipelining, which means that the receiver must be able to accept data on the cycle in which AV1READY is de-asserted. The receiving interface does not have to accept data on the cycle in which AV1READY is asserted.
99
AV1CLK
I/O
100
AV1FSYNC
I/O
101 102
AV1 SY AV1VALID
I/O I/O
103
AV1SYNC
I/O
105, 104 117, 116, 115, 114, 111, 110, 109, 108
AV1EMI[1:0] AV1 D[7:0]
O I/O
I
O
2000 Dec 01
5
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
9.3 AV Interface 2
NOTE: This AV interface may be configured to transmit or receive according to the condition of "DIRAV1" bit in GLOBCSR register--default is receive. PIN No. PIN SYMBOL AV2ERR0/ LTLEND I/O NAME AND FUNCTION CRC error, indicates bus packet containing AV2 D [7:0] had a CRC error, the current AV packet is unreliable. This pin is also used to input the mode of LTLEND (Little Endian) bit after a chip reset. An appropriate pull-up or pull-down resistor (22 k recommended) should be connected to place the pin in the desired state during reset. Please see details related to use of the LTLEND bit in the "Host Interface" section (of the datasheet (Section 12.5). Sequence Error. Indicates at least one source packet was lost before the current AV2 D [7:0] data. This pin is also used to input the mode of DATINV (Data Invariant) bit after a chip reset. An appropriate pull-up or pull-down resistor (22 k recommended) should be connected to place the pin in the desired state during reset. Please see details related to use of the DATINV bit in the "Host Interface" section (of the datasheet (Section 12.5). End of application packet indication from data source. Required only if input packet is not multiple of 4 bytes. It can be tied LOW for data packets that are 4*N in size. External application clock. Rising edge active. This pin can be programmed to be an output and the application clock. Depending on the configuration of AV Port 2 as transmitter or receiver, the output enable is located in the ITXPKCTL register (address 0x020) or IRXPKCTL register (address 0x040). Programmable frame sync, is set to input when AV interface 2 is a transmitter, and to output when the interface is configures as a receiver. When the pin is an input, it is used to designate a frame of data for Digital Video (DV). The signal is time stamped and transmitted in the SYT field of ITXHQ2. When set to an output, the signal is derived from SYT field of IRXHQ2. SY Value: When port AV2 is configured as a transmitter, this pin is an input. When the AV port is configured to as a receiver, the pin is an output. See the description for bit 0 of the ITXCTL (0x034) and IRXCTL (0x054) registers. Indicates data on AV2 D [7:0] is valid. Indicates that the data currently being clocked by the source under the condition of AV2VALID is the start of an application packet. If the AV interface is configured as a receiver, then it will assert AV2SYNC when an application packet becomes available and persist until the first data of the packet is clocked out. Thus, AV2VALID may last for more than one cycle, but for exactly one cycle in which AV2VALID is asserted. Encryption Mode Indication pins. Outputs encryption mode when this AV port is in receive state with decipher enabled. Audio/Video Data 7 (MSB) through 0. Part of byte-wide interface to the AV layer 2. When the AV port is configured as a receiver, this pin is an input. This is a flow control signal that allows the application to indicate whether it is able to accept data flowing across AV Interface 2. The AV interface responds to an inactive AV2READY by not asserting AV2VALID, and thereby withholding data from the application. The AV2READY signal is processed through one level of pipelining, which means that the AV Link will accept data on the cycle in which AV2READY is de-asserted and will not accept data on the cycle in which AV2READY is asserted. 143 AV2READY When the AV port is configured to transmit, this pin is an output. This is a flow control signal that allows the link chip to indicate whether it is able to accept data flowing across AV Interface 2. The source of data, and external entity, responds to an inactive AV2READY by not asserting AV2VALID, and thereby withholding data. The AV2READY signal should be processed by the sink through one level of pipelining, which means that the receiver must be able to accept data on the cycle in which AV2READY is de-asserted. The receiving interface does not have to accept data on the cycle in which AV2READY is asserted.
121
I/O
122
AV2ERR1/ DATINV
I/O
123
AV2ENDPCK
I
124
AV2CLK
I/O
125
AV2FSYNC
I/O
126 127
AV2 SY AV2VALID
I/O I/O
128
AV2SYNC
I/O
130, 129 142, 141, 140, 139, 136, 135, 134, 133
AV2EMI[1:0] AV2 D[7:0]
O I/O
I
O
2000 Dec 01
6
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
9.4 Phy Interface
PIN No. 82, 81, 80, 79, 76, 75, 74, 73 86, 85 47 87 88 91 92 PIN SYMBOL PHY D[0:7] PHY CTL[0:1] 1394 MODE LREQ SCLK LPS LINKON I/O I/O I/O I O I O I NAME AND FUNCTION Data 0 (MSB) through 7 (NOTE: To preserve compatibility to the specified Link-Phy interface of the IEEE 1394-1995 standard, Annex J, bit 0 is the most significant bit). Data is expected on AV D[0:1] for 100Mb/s, AV D[0:3] for 200Mb/s, and AV D[0:7] for 400Mb/s. See IEEE 1394-1995 standard, Annex J for more information. Control Lines between Link and Phy. See 1394 Specification for more information. 1394-1995 Annex J PHY (HIGH), or 1394.a PHY (LOW) Link Request. Bus request to access the PHY. See IEEE 1394-1995 standard, Annex J for more information. (Used to request arbitration or read/write PHY registers). System clock. 49.152MHz input from the PHY (the PHY-LINK interface operates at this frequency). Link power status. L41 generates a host interrupt when this pin receives a link on signal from the PHY. Interrupt is a request from another node for the L41 to be powered up (see PD pin). Isolation mode. This pin is asserted (LOW) when an Annex J type isolation barrier is used. See IEEE 1394-1995 Annex J. for more information. When tied HIGH, this pin enables internal bushold circuitry on the affected PHY interface pins (see below). Active bushold circuits allow either the direct connection to PHY pins or the use of the single capacitor isolation mode.
93
ISON
I
9.5 Other Pins
PIN No. 5, 11, 17, 23, 34, 43, 53, 60, 69, 77, 83, 89, 94, 106, 112, 119, 131, 137 6, 12, 18, 24, 35, 44, 54, 61, 70, 78, 84, 90, 95, 107, 113, 120, 132, 138 48 49, 50, 51, 52, 58, 59, 65, 66, 67, 68, 71, 72 144 55 56 57 62, 63, 64 PIN SYMBOL I/O NAME AND FUNCTION
GND
Ground reference
VDD
3.3 V 0.3 V power supply
PD1,2,3,4
I
Power Down. When asserted (high), the AV Link goes into a low power mode and de-asserts the LPS pin. When in this state, reads and writes to the registers are not allowed. The AV Link will resume operation when PD is de-asserted (low), all register settings and configurations are restored to their pre power down values. These pins are reserved for factory testing. For normal operation they should be connected to ground. Auxiliary clock, value is SCLK (usually 49.152 MHz) Provides the capability to supply an external cycle timer signal for the beginning of 1394 bus cycles. Reproduces the 8kHz cycle clock of the cycle master. Test pins. These signals must be connected to ground.
RESERVED CLK50 CYCLEIN CYCLEOUT TESTPIN
NA O I O
NOTES: Before asserting the RPL bit, SWPD or setting the PD pin high, the user should assure that the link chip is in the following state of operation: 1. The isochronous transmit FIFO is not receiving data for transmission 2. The isochronous transmitter is disabled 3. No asynchronous packets are being generated for transmission 4. Both the ASYNC request and response queues are empty
2000 Dec 01
7
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
10.0 RECOMMENDED OPERATING CONDITIONS
LIMITS SYMBOL VCC VI VIH VIL IOH IOL dT/dV Tamb SCLK AVCLK tr tf PARAMETER DC supply voltage Input voltage High-level input voltage Low-level input voltage High-level output current Low-level output current Input transition rise or fall time Operating ambient temperature range System clock AV interface clock Input rise time input fall time 0 0 49.147 0 CONDITIONS MIN. 3.0 0 2.0 0.8 4 -4 20 +70 49.157 24 10 10 MAX. 3.6 5 UNIT V V V V mA mA ns/V C MHz MHz ns ns
11.0 ABSOLUTE MAXIMUM RATINGS1, 2
In accordance with the Absolute Maximum Rating System (IEC 134). Voltages are referenced to GND (ground = 0 V). LIMITS SYMBOL VDD IIK VI IOK VO IO IGND, ICC Tstg Tamb Ptot PARAMETER DC supply voltage DC input diode current DC input voltage DC output diode current DC output voltage DC output source or sink current DC VCC or GND current Storage temperature range Operating ambient temperature Power dissipation per package CONDITIONS MIN -0.5 - -0.5 - -0.5 - - -60 0 MAX +4.6 -50 +5.5 50 VDD +0.5 50 150 150 70 0.6 UNIT V mA V mA V mA mA C C W
NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150 C.
2000 Dec 01
8
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.0 FUNCTIONAL DESCRIPTION 12.1 Overview
The PDI1394L41 is an IEEE1394-1995 and IEEE1394.a compliant link layer controller. It provides a direct interface between a 1394 bus and various MPEG-2 and DVC codecs. The AV Link maps and unmaps AV data streams and similar data onto 1394 isochronous packets. Data can be ciphered or deciphered according to the `5C' standard method of content protection. The AV Link also provides an 8 bit or 16 bit wide host interface for an attached microcontroller. Through the host interface port, the host controller can configure the AV layer for transmission or reception of AV datastreams. The host interface port also allows the host controller to transmit and receive 1394 asynchronous data packets.
12.2 AV interface and AV layer
The AV interface and AV layer format "application packets" according to the IEC 61883 specification for isochronous transport over the 1394 network. The AV transmitter and receiver within the AV layer perform all the functions required to pack and unpack AV packet data for transfer over a 1394 network. Once the AV layer is properly configured for operation, no further host controller service should be required. The operation of the AV layer is full-duplex, i.e., the AV layer can receive and transmit AV packets on the same bus cycle. 12.2.1 IEC 61883 International Standard The PDI1394L41 is specifically designed to support the IEC61883 International Standard of Digital Interface for Consumer Electronic Audio/Video Equipment. The IEC specification defines a scheme for mapping various types of AV datastreams onto 1394 isochronous data packets. The standard also defines a software protocol for managing isochronous connections in a 1394 bus called Connection Management Protocol (CMP). It also provides a framework for transfer of functional commands, called Function Control Protocol (FCP). 12.2.2 CIP Headers A feature of the IEC61883 International Standard is the definition of Common Isochronous Packet (CIP) headers. These CIP headers contain information about the source and type of datastream mapped onto the isochronous packets. The AV Layer supports the use of CIP headers. CIP headers are added to transmitted isochronous data packets at the AV data source. When receiving isochronous data packets, the AV layer automatically analyzes their CIP headers. The analysis of the CIP headers determines the method the AV layer uses to unpack the AV data from the isochronous data packets. The information contained in the CIP headers is accessible via registers in the host interface. (See IEC61883 International Standard of Digital Interface for Consumer Electronic Audio/Video Equipment for more details on CIP headers). 12.2.3 The AV Interface The AV link's 8-bit parallel interface is synchronous with AVxCLK, and was designed to interface with various MPEG-2 and DVC codecs. The AV interface port buffer, if so programmed, can time stamp incoming AV packets. The AV packet data is stored in the embedded memory buffer, along with its time stamp information. After the AV packet has been written into the AV layer, the AV layer creates an isochronous bus packet with the appropriate CIP header. The bus packet along with the CIP header is transferred over the appropriate isochronous channel/packet. The size and configuration of isochronous data packet payload transmitted is determined by the AV layer's configuration registers accessible through the host interface. The AV interface port waits for the assertion for AVxVALID and AVxSYNC. AVxSYNC is aligned with the rising edge of AVxCLK and the first byte of data on AVxDATA[7:0]. The duration of AVxSYNC is one AVxCLK cycle. AVxSYNC signals the AV layer that the transfer of an AV packet has begun. At the time the AVxSYNC is asserted, the AV layer creates a new time stamp in the buffer memory. (This only happens if so configured. The DVC format does not require these time stamps). The time stamp is then transmitted as part of the source packet header. This allows the AV receiver to provide the AV packet for output at the appropriate time. Only one AVSYNC pulse is allowed per application packet; if additional sync pulses are presented before the full packet is inputted, a new packet will be started and the previously inputted packet data will be discarded (and not transmitted) in conjunction with the input error interrupt bit (INPERR, bit 3 of register 0x02C) being set to flag the error. An additional synchronization mechanism is defined by the IEC 61883 specification, called frame sync. The frame synchronization signal AVxFSYNC is time stamped and placed in the SYT field of the CIP header. The default delay value for the frame sync is 3 bus cycle times (duration of 125 s each) in the future, and is transmitted on the very next isochronous cycle regardless of available data. The PDI1394L41 allows this value to be programmable from 2 to 4 cycle times (see Section 13.2.1). Additionally, for some audio applications, the SYT value can be programmed to be appended only to isochronous cycles that have application data attached to them. This mode is enabled via the AUDIO bit (again, see Section 13.2.1). When the AUDIO mode is enabled, two additional cycle delays are automatically added to the SYT_DELAY value (bits 6 and 5 of the ITXPKCLT register). On the receiver side, when the SYT stamp matches the cycle timer register, a pulse is generated on the AVxFSYNC output. The timing for AVxFSYNC is independent of AVxCLK. The maximum repetition rate of application-presented AVFSYNC pulses is limited to 8,000 pulses per second (the bus cycle rate). In the rare instance of SYT queue overflow with possible loss of up to 7 AVFSYNC pulses, the "SYTOVF" interrupt (bit 14 in register 0x04C) will occur. If an SYTOVF interrupt occurs, the contents of the SYT queue is automatically flushed and normal operation automatically resumes. Some applications would like to create their own transmit timestamps independent of the AV Layer. On receive, these applications would like to process the embedded time stamps instead of allowing the AV Layer to process these time stamps. This can be accommodated via the ENXTMSTMP bit in the ITXPKCTL register for transmit and DIS_TSC bit in the IRXPKCTL register for receive. In conjunction with this mode, additional means of flow control are enabled via the AVxREADY signal.
2000 Dec 01
9
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
Port Dir Transmit Receive
AVxREADY Out In
Description The L41 is prepared to receive a byte. The attached device will not assert AVVALID for any cycle in which AVxRDY is false. The attached device is prepared to receive a byte. The L41 will not assert AVxVALID for any cycle in which AVxREADY is false.
When the AV port is configured as a receiver, the AVxSYNC signal will be asserted as soon as the PDI1394L41 AVx port has an application packet available for delivery (independent of AVxREADY) and will remain asserted until the first byte of the application packet is clocked from the AV port. 12.2.4 Content Protection The AV Layer incorporates features to implement the Digital Transmission Copy Protection (DTCP) scheme that is specified by the Digital Transmission Licensing Authority (DTLA). The DTCP specification consists of two primary functions: stream ciphering and authentication. Refer to "5C Digital Transmission Content Protection Specification - Volume 1" for more details about the DTCP scheme. On the AV Link stream ciphering is accomplished by internal 56 bit M6 content cipher and decipher blocks. To ease software development effort and reduce the loading on the controlling processor, the link chip also includes a cryptographic accelerator capable of doing elliptic curve multiplications and Sign and Verify operations. Due to the size and number of operands for the M6 and cryptographic accelerator blocks, the host interface register set has been extended to provide additional control and data registers. These extensions have been implemented via an indirect addressing mechanism. This mechanism allows software written for previous versions of the AV Link (PDI1394L21 and PDI1394L11) to operate on the PDI1394L41. Note, however, that some extensions to the interrupt registers were made to accommodate interrupts originating from the content protection block. For a full description of the use of the L41's content protection features please see data sheet addendum AL41-1. AL41-1 addendum can be requested from Philips by DTLA licensees by e-mailing 1394@philips.com. One paper copy of this addendum is available to each DTLA licensee after verification of license status. Please see Section 2.1 of this data sheet for further information. DTLA license information is available at http://www.dtcp.com.
2000 Dec 01
10
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.2.5 Audio Support The AV transmitter has some additional features to support some types of audio transport. These are enabled by setting bit 30 (AUDIO) of ITXPKCTL (0x020) to logic 1. At the rising edge of AVxFSYNC, a SYT time stamp will be generated and written into the SYT queue of the isochronous transmitter. This stamp will point to a time in the future dictated by the following formula: SYT[15:12] = CYCTM[15:12] + programmed SYT_DELAY value + 2 SYT[11:0] = CYCTM[11:0] The additional delay of two cycles is specific to this AUDIO mode. The oldest SYT time stamp in the SYT queue will be sent first, but only when accompanied by a data payload. Any pending SYT time stamp will be held until the next non-empty bus packet is sent. At the moment of transmission, the SYT time stamp should at least point one cycle in the future. If it points to a time that is less than one cycle in the future, it will be discarded. The SYT queue in the isochronous transmitter can store 4 entries, the SYT queue in the isochronous receiver can store six entries. This supports the case where an 8 kHz signal is applied to AVxFSYNC, and AUDIO = 1, and SYT_Delay = 2. Assuming there is data on every cycle, the receiver will receive an SYT time stamp each cycle with the first SYT time stamp pointing just less than six cycles in the future. When the SYT queue in the isochronous receiver is full, then the most recently received SYT time stamp is overwritten with the next arriving SYT time stamp. If the queue should become full or contain a corrupted time stamp, the queue will automatically clear and indicate so by setting the "SYTOVF" interrupt. 12.2.6 SY - Sync Support This feature supports the 1394 digital camera specification. The state of this pin will be reflected in the SY bit (ITXCTL register 0x034) and will be transmitted along with the isochronous data block that was entered with it. The intended use of this pin is to signal the start of a new frame of video in the isochronous header section of the data payload. Similarly, the isochronous receiver will assert the AVxSY pin simultaneously with the first byte of the isochronous bus packet in which the SY value was received. NOTE: The SY functionality is only intended to be used when the M6 cipher and de-cipher are not enabled.
AV DATA AV SYNC AV SY
SV01787
Figure 1. Behavior of "SY" signal at AVport of receiver
12.2.7 Programmable Buffer Memory The PDI1394L41 maintains six distinct buffers that are highly configurable to optimize bandwidth capabilities. Buffers can be increased or decreased from the default value by accessing the indirect address range of 0x100 through 0x1FC (INDADDR, 0x0F8). If the AV Layer is configured to transmit or receive DVB compliant MPEG-2 type data, the default Isochronous (AV) buffer sizes are recommended. FIFO sizes cannot be changed dynamically; after a FIFO size change, transmitters and receivers must be reset. Buffers can be programmed with 64 quadlet (256 Byte) granularity. Minimum buffer size is 64 quadlets, maximum buffer size is limited to 11 kB. The sum of all buffers cannot exceed 12K Bytes, or 3K Quadlets.
DEFAULT BUFFER SIZE
BUFFER MEMORY Asynchronous Receive Response FIFO Asynchronous Receive Request FIFO Asynchronous Transmit Response FIFO Asynchronous Transmit Request FIFO Isochronous (AV) Transmit Buffer Isochronous (AV) Receive Buffer SIZE (Quadlets) 256 256 256 256 1024 1024
2000 Dec 01
11
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.3 Bushold and Link/PHY single capacitor galvanic isolation
12.3.1 Bushold The PDI1394L41 uses an internal bushold circuit on each of the indicated pins to keep these CMOS inputs from "floating" while being driven by a 3-Stated device or input coupling capacitor. Unterminated high impedance inputs react to ambient electrical noise which cause internal oscillation and excess power supply current draw. The following pins have bushold circuitry enabled when the ISON pin is in the logic "1" state: Name PHY CTL0 PHY CTL1 PHY D0 PHY D1 PHY D2 PHY D3 PHY D4 PHY D5 PHY D6 PHY D7 SYSCLK Function PHY control line 0 PHY control line 1 PHY data bus bit 0 PHY data bus bit 1 PHY data bus bit 2 PHY data bus bit 3 PHY data bus bit 4 PHY data bus bit 5 PHY data bus bit 6 PHY data bus bit 7 System clock input to the link
Philips bushold circuitry is designed to provide a high resistance pull-up or pull-down on the input pin. This high resistance is easily overcome by the driving device when its state is switched. Figure 2 shows a typical bushold circuit applied to a CMOS input stage. Two weak MOS transistors are connected to the input. An inverter is also connected to the input pin and supplies gate drive to both transistors. When the input is LOW, the inverter output drives the lower MOS transistor and turns it on. This re-enforces the LOW on the input pin. If the logic device which normally drives the input pin were to be 3-Stated, the input pin would remain "pulled-down" by the weak MOS transistor. If the driving logic device drives the input pin HIGH, the inverter will turn the upper MOS transistor on, re-enforcing the HIGH on the input pin. If the driving logic device is then 3-Stated, the upper MOS transistor will weakly hold the input pin HIGH. The PHY's outputs can be 3-Stated and single capacitor isolation can be used with the Link; both situations will allow the Link inputs to float. With bushold circuitry enabled, these pins are provided with dc paths to ground, and power by means of the bushold transistors; this arrangement keeps the inputs in known logical states.
INPUT PIN
INTERNAL CIRCUITS
SV00911
Figure 2. Bushold circuit
2000 Dec 01
12
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.3.2 Single capacitor isolation The circuit example (Figure 3) shows the connections required to implement basic single capacitor Link/PHY isolation. NOTE: The isolation enablement pins on both devices are in their "1" states, activating the bushold circuits on each part. The bushold circuits provide local dc ground references to each side of the isolating/coupling capacitors. Also note that ground isolation/signal-coupling must be provided in the form of a parallel combination of resistance and capacitance as indicated in the IEEE 1394 standard.
APPLICATION/LINK +3.3V
ISOLATED/PHY +3.3V
LINK PDI1394L41
ISON SCLK PHY D0 PHY D1 PHY D2 PHY D3 PHY D4 PHY D5 PHY D6 PHY D7 PHYCTL0 PHYCTL1 LREQ LPS LINKON
Cc Cc Cc Cc Cc Cc Cc Cc Cc Cc Cc Cc CL
ISO- SYSCLK PHY D0 PDI1394P2x D1 D2 D3 D4 D5 D6 D7 PHYCTL0 PHYCTL1 LREQ LPS LINKON
APPLICATION AND LINK GROUND
LINK 3.3V
CC
PHY 3.3V
ISOLATED PHY GROUND
13K
VALUES OF THESE RESISTORS DEPEND ON PHY USED. SEE PHY DATASHEET.
9.1K ALSO SEE APPLICATION NOTE AN2452 FOR MORE DETAILS Cc 1MEG Cr CC = 1 nF; Cr = 100 nF; CL = 3.3nF
SV01816
Figure 3. Single capacitor Link/PHY isolation
12.4 Power Management
The PDI1394L41 implements several features for power management as noted in the 1394a-2000 standard. These features include: 1. Reset of the Phy/Link interface by setting the RPL bit in the LNKCTL register. 2. Disable of the Phy/Link interface caused by either setting the SWPD bit in the RDI register -OR- asserting (high) the PD pin. 3. Initialization of the Phy/Link interface after it was disabled or reset. The application can power up the Phy/Link interface by deasserting the PD pin -OR- clearing (low) the SWPD in the RDI register. This will cause the L41 to produce a pulsing signal on the LPS pin. When the L41 is in power down mode, reads and writes to the host interface will be restricted to those addressing only the RDI register (0x0B0). Please see Section 13.3.11 for further details. There are 3 ways to power up the L41. (1) When the application wants the 1394 node to resume operation, it simply needs to de-assert the PD pin, or (2) clear the SWPD bit in the RDI register. The link can also be awakened by another bus node sending a link-on packet to the PHY of the application's node. (3) The attached PHY will activate its LinkOn line and the L41 will see the signal and set the LOA bit of the RDI register. Assuming that the ELOA bit is in its enabled, "1", state, the L41 will generate an interrupt of the host processor. It will then be up to the host processor to decide whether to honor the link-on request of the other node. Then the host processor will de-assert the PD pin -OR- clear the SWPD bit in the RDI register. This activity will power up the L41 causing it to send the pulsing signal out on the LPS pin which notifies the PHYchip of link activity and allows the PHY to discontinue directing the link on signal to the L41. Subsequently, the host processor must acknowledge the LOA interrupt by writing a "1" to the LOA bit position in the RDI register after the link on signal from the PHY has stopped.
2000 Dec 01
13
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.5 The host interface
The host interface allows an 8 bit or 16 bit CPU to access all registers and the asynchronous packet queues. It is designed to be easy to use with a wide range of processors, including 8051, MIPS1900, ST20, PowerPC etc. The host interface can work with 8 bit or 16 bit wide data paths, and offers multiplexed or non-multiplexed access. There are 64 register addresses (for quadlet wide registers). To access bytes rather than quadlets the address space is 256 bytes, requiring 8 address lines. The use of an 8 bit or 16 bit interface introduces an inherent problem that must be solved: register fields can be more than 8 bits wide and be used (control) or changed (status) at every internal clock tick. If such a field is accessed through an 8 bit or 16 bit interface it requires more than one read or write cycle, and the value should not change in between to maintain consistency. To overcome this problem accesses to the chip's internal register space are always 32 bits, and the host interface must act as a converter between the internal 32 bit accesses and external 8 bit or 16 bit accesses. This is where the shadow register (0x0F4) is used. 12.5.1 Read accesses To read an internal register the host interface can make a snapshot (copy) of that specific register which is then made available to the CPU 8 or 16 bits at a time. The register that holds the snapshot copy of the real register value inside the host interface is called the shadow register. During an 8-bit read cycle address lines HIF A0 and HIF A1 are used to select which of the 4 bytes currently stored in the shadow register is output onto the CPU data bus. This selection is done by combinatorial logic only, enabling external hardware to toggle these lines through values 0 to 3 while keeping the chip in a read access mode to get all 4 bytes out very fast (in a single extended read cycle), for example into an external quadlet register. During a 16 bit read cycle address line HIF A1 is used to select which pair of 4 bytes currently stored in the shadow register is output to the CPU bus. Again the selection is by combinatorial logic, enabling external hardware to toggle HIF A1 while keeping the chip in read access mode to get both words very quickly. This solution requires a control line to direct the host interface to make a snapshot of an internal register when needed, as well as the internal address of the target register. The register address is connected to input address lines HIF A2..HIF A7, and the update control line to input address line HIF A8. To let the host interface take a new snapshot the target address must be presented on HIF A2..HIF A7 and HIF A8 must be raised while executing a read access. The new value will be stored in the shadow register and the selected byte (HIF A0, HIF A1, 8 bit mode) or word (HIF A1, 16 bit mode) appears on the output. Not all registers can be accessed in Direct Address Space. Some of the registers are in an indirect address space, these registers control the FIFO size and content protection system. The correct internal register space has to be selected through the host interface, using directly addressable registers INDADDR (0x0F8) and INDDATA (0x0FC).
TR MUX SHADOW REGISTER MUX Q
8/16 CPU
32
32 Q
REGISTERS HIF A0..1 (8 BIT MODE) HIF A1 (16 BIT MODE) HIF A2..7 HIF A8 UPDATE/COPY CONTROL 32
SV01034
NOTES: 1. It is not required to read all 4 bytes of a register before reading another register. For example, in 8 bit mode, if only byte 2 of register 0x54 is required a read of byte address 0x100 + (0x54) + 2 = 0x156 is sufficient. 2. The update control line does not necessarily have to be connected to the CPU address line HIF A8. This input could also be controlled by other means, for example a combinatorial circuit that activates the update control line whenever a read access is done for byte 0. This makes the internal updating automatic for quadlet reading. 3. Reading the bytes of the shadow register can be done in any order and as often as needed. 4. It is possible to read/modify/write a register using the shadow register (0x0F4) without rewriting all 4 bytes. For example, to modify an enable bit in the fourth byte of the Asynchronous Interrupt Enable (0x0A4), a read of location 0x100+0x0A0+3=0x1A3, followed by a write of the modified byte to the same location 0x100+0x0A0+3=0x1A3 is sufficient. The other bytes remain unchanged.
2000 Dec 01
14
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.5.2 Write accesses To write to an internal register the host interface must collect the 4 byte values (8 bit mode) or 2 word values (16 bit mode) into a 32 bit value and then write the result to the target register in a single clock tick. This requires a register to hold the 32 bit value being compiled until it is ready to be written to the actual target register. This temporary register inside the host interface is called the shadow register. In 8 bit mode, address lines HIF A0 and HIF A1 are used to select which of the 4 bytes of the shadow register is to be written with the value on the CPU data bus. In 16 bit mode, HIF A1 is used to select which half of the shadow register is to be written with the value on the CPU data bus. Only one byte (8 bit mode) or one word (16 bit mode) can be written in a single write access cycle. Not all registers can be accessed in Direct Address Space. Some of the registers are in an indirect address space, these registers control the FIFO size and content protection system. The correct internal register space has to be selected through the host interface, using directly addressable registers INDADDR (0x0F8) and INDDATA (0x0FC).
TR MUX SHADOW REGISTER MUX Q
8/16 CPU
32 Q
REGISTERS HIF A0..1 (8 BIT MODE) HIF A1 (16 BIT MODE) HIF A2..7 HIF A8 UPDATE/COPY CONTROL 32
SV01035
NOTES: 1. It is not required to write all 4 bytes, or both words of a register: those bytes that are either reserved (undefined) or don't care do not have to be written in which case they will be assigned the value that was left in the corresponding byte of the shadow register from a previous write access. For example, to acknowledge an interrupt for the isochronous receiver in 8 bit mode, a single byte write to location 0x100+(0x4C)+3 = 0x14F is sufficient. The value 256 represents setting HIF A8=1. The host interface cannot directly access the FIFOs, but instead reads from/writes into a transfer register (shown as TR in the Figures above). Data is moved between FIFO and TR by internal logic as soon as possible without CPU intervention. 2. The update control line does not necessarily have to be connected to the CPU address line HIF A8. This input could also be controlled by other means, for example a combinatorial circuit that activates the update control line whenever a write access is done for byte 3 or the upper 16 bits. This makes the internal updating automatic for quadlet writing. 3. Writing the bytes or words of the shadow register can be done in any order and as often as needed (new writes simply overwrite the old value). 4. It is now possible to read/modify/write a register using the shadow register (0x0F4) without rewriting all 4 bytes. For example, to modify an enable bit in the fourth byte of the Asynchronous Interrupt Enable (0x0A4), a read of location 0x100+0x0A0+3=0x1A3, followed by a write of the modified byte to the same location 0x100+0x0A0+3=0x1A3 is sufficient. The other bytes remain unchanged.
2000 Dec 01
15
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.5.3 Accessing the RDI register (Power-down, Power-up) Accessing the RDI register is a special situation, but software written to access all other link base registers can still be used. This register can be read and written with the link chip in power-down mode; this means that there is no system clock present within the link chip. The system clock is required to access all other link registers due to the fact that multiple clock cycles are required to fetch data to the shadow register or write data from the shadow register to the targeted internal register. Reading and writing to the RDI register is done through purely combinatoral logic, there is no access through the shadow register. The RDI register is accessed directly through the host interface using the same method of access required by other link base registers. The RDI register contains control, status and interrupt bits. Operation of the status and interrupt bits in the RDI register differs slightly from these types of bits in other registers. Operation falls into four categories: (1) pure status bit, (2) interrupt/status bit, (3) control bit, (4) interrupt control bit. LPSTAT is a pure status bit; this means that LPSTAT continually reflects the status of the LPS signal on the link-phy interface. If LPSTAT = 1, the LPS signal is active. If LPSTAT = 0, the LPS signal to the phy chip is inactive. It should be noted here that the LPSTAT bit should NOT be used as an indicator of link chip activity because the LPS signal may be inactive for short (25 uS) periods of time if the link chip is performing a phy-link interface reset function. SCI is also a pure status bit when it is not enabled as an interrupt. SCI will reflect the INVERSE status of the system clock at all times. When the system clock (SCLK) is active, SCI = 0. When the SCLK is inactive, SCI = 1. The SCI bit can also be used as an interrupt bit by setting ESCI = 1. In this mode of operation when the SCI = 1, an interrupt will be generated to indicate that the SCLK has become inactive. This interrupt is serviced in the same manner as all other link register interrupts... write a "1" back to the SCI bit position in order to acknowledge the interrupt. PLI, LOA and SCA are interrupt/status bits. These bits may be enabled as interrupts (by setting the corresponding interrupt control bit EPLI, ELOA, or ESCA =1). These bits are ALSO status bits when the corresponding interrupt enabling bit is = 0. However, if any of these bits sets (=1) while in the status bit mode, it must be written with a "1" to be reset... similar operation to interrupt bit operation elsewhere in the link registers. Also, like other interrupt bits in the link registers, in order to acknowledge an interrupt of any of these bits, it is necessary to write a "1" back to the bit position to acknowledge the interrupt; this resets the bit to "0". [Please bear in mind that the functions represented by these bits are continuous; so we recommend that before the interrupt is acknowledged, the corresponding enable bit should be set to "0", else the interrupt will immediately happen again.] SWPD is a control bit. There are two ways to affect a power-down of the link chip. Setting SWPD will stop the link chip from transmitting the LPS signal to the phy chip and thus cause the phy to withhold the SCLK, thus powering-down the link chip. Raising the link PD pin to the high level will also accomplish power-down in a similar manner. DO NOT USE BOTH METHODS to affect a power-down. The SWPD bit, being a control bit, will NOT reflect the state of the PD pin. If the SWPD bit is = 0 and the SCI bit is = 1, it's a good bet that the PD pin is active if the phy chip is operating. In this case the PD pin MUST be reset low before the link will power-up. EPLI, ELOA, ESCA, and ESCI are interrupt enable bits. Setting any of these bits = 1 will cause the corresponding interrupt bit to become an active interrupt when that bit sets. If these bits are set = 0, the corresponding PLI, LOA, SCA, and SCI bit is in the interrupt/status mode as described above. (Also see the individual bit descriptions in the RDI register section of this data sheet... Section 13.3.1)
2000 Dec 01
16
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.5.4 Big and little endianness, data invariance, and data bus width The host interface offers programmable endianness, data invariance, and selectable 8 and 16 bit data widths. LTLEND (pin 121) and DATINV (pin 122) are multiplexed configuration pins that will be sampled on the trailing edge of RESET; the states of these pins are established by connecting each pin to the proper logic state, ground or VDD, through a resistor, 22 k is recommended. To verify the configuration, the shadow register (0x0F4) will be preset to a value of 0x0F0A0500 after a power reset. Table 1 describes the configurations.
Table 1. Configuration possible combinations
LTLEND (Little Endian) 1 1 0 0 DATINV (Data Invariant) 1 0 X X HIF 16BIT See Table 2 1 1 0 Result Byte/Word address is reversed Bytes are swapped within the word 16-bit data bus, address as in PDI1394L21 8-bit data bus, address as in PDI1394L21
Table 2. Explanation of the mode LittleEnd = 1, DataInvariant = 1
HIF16 = 0 Outside Address (A1, A0) 00 01 10 11 Inside Address (A1, A0) 11 10 01 00 0X 0X 1X 1X HIF16 = 1 Outside Address (A1, A0) Inside Address (A1, A0) 1X 1X 0X 0X
It is important to note that some operands in the indirect address space consist of more than one quadlet. For these operands, the lowest address always contains the most significant quadlet. In Bit Endian mode and DATAINV = 0, the bytes in each quadlet are numbered 0..3 from left (most significant) to right (least significant) as shwon in Figure 4. To access a register in 8 bit HIF mode, at address N the CPU should use addresses E: E = N ; to access the upper 8 bits of the register. E = N + 1 ; to access the upper middle 8 bits of the register. E = N + 2 ; to access the lower middle 8 bits of the register. E = N + 3 ; to access the lower 8 bits of the register. To access a register in 16 bit HIF mode, at internal address N, the CPU should use addresses E: E = N ; to access the upper 16 bits of the register E = N + 2 ; to access the lower 16 bits of the register
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BYTE 0
BYTE 1
BYTE 2
BYTE 3
SV00656
Figure 4. Byte order in quadlets as implemented in the host interface, HIF LTLEND = LOW
2000 Dec 01
17
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
In Little Endian mode and DATAINV = 0, the bytes in each quadlet are numbered 3. .0 from the left (most significant) to right (least significant) as shown in Figure 5. To access a register in 8 bit HIF mode, at address N the CPU should use addresses E: E = N + 3 ; to access the upper 8 bits of the register E = N + 2 ; to access the upper middle 8 bits of the register E = N + 1 ; to access the lower middle 8 bits of the register E = N ; to access the lower 8 bits of the register To access a register in 16 bit HIF mode, at internal address N, the CPU should used addresses E: E = N ; to access the lower 16 bits of the register E = N + 2 ; to access the upper 16 bits of the register
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BYTE 3
BYTE 2
BYTE 1
BYTE 0
SV01079
Figure 5. Byte order in quadlets as implemented in the host interface, HIF LTLEND = HIGH
12.5.5 Accessing the asynchronous packet queues Although entire incoming packets are stored in the receiver buffer memory they are not randomly accessible. These buffers act like FIFOs and only the frontmost (oldest) data quadlet entry is accessible for reading. Therefore only one location (register address) is allocated to each of the two receiver queues. Reading this location returns the head entry of the queue, and at the same time removes it from the queue, making the next stored data quadlet accessible. With the current host interface such a read is in fact a move operation of the data quadlet from the queue to the shadow register. Once the data is copied into the shadow register it is no longer available in the queue itself so the CPU should always read all 4 bytes, or both words, before attempting any other read access (be careful with interrupt handlers for the PDI1394L41!).
2000 Dec 01
18
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.5.6 The CPU bus interface signals The CPU interface is directly compatible with a wide range of microcontrollers, and supports both multiplexed and non-multiplex access. It uses separate HIF RDN, HIF WRN, HIF ALE, and HIF CSN chip select lines. There are 9 address inputs (HIF A0..HIF A8) and 8 or 16 data in/out lines HIF D[7:0] or HIF D [15:0]. The upper 8 bits of the data in/out lines are only used when the 8/16 bit mode pin (HIF16BIT) is held HIGH. The CPU is not required to run a clock that is synchronous to the 1394 base clock. The control signals will be resampled by the host interface before being used internally. In non-multiplex mode (HIF MUX = LOW), an access through the host interface starts when HIF CSN = 0 and either HIF WRN = 0 or HIF RDN = 0. Typically the chip select signal is derived from the upper address lines of the CPU (address decode stage), but it could also be connected to a port pin of the CPU to avoid the need for an external address decoder in very simple CPU systems. When both HIF CSN = 0 and HIF RDN = 0 the host interface will start a read access cycle, so the cycle is triggered at the falling edge of either HIF CSN or HIF RDN, whichever is later. In multiplex mode (HIF MUX = HIGH), an access through the host interface starts when HIF CSN = 0 and either HIF WRN = 0 or HIF RD_N = 0. The address must now be presented on the HIF AD [7:0] lines, and will be latched on the falling edge of ALE. If HIF RDN = 0, data will be offered after the falling edge of ALE. If HIF WRN = 0, data has to be presented by the microcontroller. In both multiplexed and non-multiplexed mode, HIF WAIT can be used to signal to the controlling CPU that an extension of the current access cycle is needed. This allows the PDI1394L41 to work in the same address space as peripherals with a shorter access time. HIF WAIT will remain HIGH for the minimum duration of the access cycle. If HIF A[8] is HIGH, HIF WAIT will extend the access cycle to 120ns to allow for the shadow register transfer to take place. Subsequent access to the same register which does not required A[8] to be raised, can be executed much faster. By connecting HIF WAIT to the appropriate input on the controlling processor, the PDI1394L41 can be mapped in memory space with faster devices. The PDI1394L41 should not be mapped in memory space with devices that require access faster than 15 ns. HIF A[7:0] can be used as a simple demultiplexer. In multiplex mode, the address on AD[7:0] will appear on A[7:0] immediately, and will remain there until the next rising edge of HIF ALE.
HIF CS_N
HIF RD_N
HIF WR_N
HIF A8
HIFA7-A0
HIFD15-D8
HIFAD7-AD0
HIF_WAIT
HIF_MUX
HIF16BIT
SV01868
NOTES: 1. ALE line is held LOW. 2. An extended read cycle may be implemented by holding CS_N and RD_N low (active) and changing only the A7-A0 address. After each new address stabilizes, wait at least tACC and read the data. The extended read cycle can be used only following a read of the first byte of the shadow register using the A8 transfer mechanism. See the section on Read Accesses (Section 12.5.1). Figure 6. 16 Bit Read Cycle Non-multiplexed
2000 Dec 01
19
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
HIF CS_N
HIF RD_N
HIF WR_N
HIFA7-A0
HIFD15-D8
HIFAD7-AD0
A8
HIF_WAIT
HIF_MUX
HIF16BIT
SV01867
NOTE: 1. ALE line is held LOW. Figure 7. 16 Bit Write Cycle Non-multiplexed
2000 Dec 01
20
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
tALEH
HIF CS_N
tPWALE tALES
HIF ALE
AD7-AD0
ADDR
DATA
ADDR
DATA
A7-A0
LATCHED
LATCHED
HIFD15-D8
DATA
DATA
A8
HIF RD_N
HIF WR_N
HIF_WAIT
HIF_MUX
HIF16BIT
SV01854
NOTE: 1. Second write cycle elongated by WAIT signal. Figure 8. 16 Bit Write Cycle Multiplexed
2000 Dec 01
21
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
tALEH
HIF CS_N
tPWALE tALES
HIF ALE
HIF AD7-AD0
ADDR
DA
TA
ADDR
DA
TA
HIF A7-A0
LATCHED
LATCHED
HIFD15-D8
DATA
DATA
A8
HIF RD_N
HIF WR_N HIF_WAIT
HIF_MUX
HIF16BIT
SV01855
Figure 9. 16 Bit Read Cycle Multiplexed
2000 Dec 01
22
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
tALEH
HIF CS_N
tPWALE tALES
HIF ALE
AD7-AD0
ADDR
DATA
ADDR
DATA
A7-A0
LATCHED
LATCHED
A8
HIF RD_N
HIF WR_N
HIF_WAIT
HIF_MUX
HIF16BIT
SV01856
Figure 10. 8 Bit Write Cycle Multiplexed
2000 Dec 01
23
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
tALEH
HIF CS_N
tPWALE tALES
HIF ALE
HIF AD7-AD0
ADDR
DA
TA
ADDR
DA
TA
HIF A7-A0
LATCHED
LATCHED
A8
HIF RD_N
HIF WR_N HIF_WAIT
HIF_MUX
HIF16BIT
SV01857
Figure 11. 8 Bit Read Cycle Multiplexed
2000 Dec 01
24
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
HIF CS_N
HIF RD_N
HIF WR_N
HIFA7-A0
HIFAD7-AD0
A8
HIF_WAIT
HIF_MUX
HIF16BIT
SV01866
NOTE: 1. ALE line is held LOW. Figure 12. 8 Bit Write Cycle Non-multiplexed
2000 Dec 01
25
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
HIF CS_N
HIF RD_N
HIF WR_N
HIF A8
HIFA7-A0
HIFAD7-AD0
HIF_WAIT
HIF_MUX
HIF16BIT
SV01865
NOTE: 1. ALE line is held LOW. Figure 13. 8 Bit Read Cycle Non-multiplexed
2000 Dec 01
26
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6 The Asynchronous Packet Interface
The PDI1394L41 provides an interface to asynchronous data packets through the registers in the host interface. The format of the asynchronous packets is specified in the following sections. 12.6.1 Reading an Asynchronous Packet Upon reception of a packet, the packet data is stored in the appropriate receive FIFO, either the Request or Response FIFO. The location of the packet is indicated by either the RREQQQAV or RRSPQAV status bit being set in the Asynchronous Interrupt Acknowledge (ASYINTACK) register. The packet is transferred out of the FIFO by successive reads of the Asynchronous Receive Request (RREQ) or Asynchronous Receive Response (RRSP) register. The end of the packet (the last quadlet) is indicated by either the RREQQLASTQ or RRSPQLASTQ bit set in ASYINTACK. Attempting to read the FIFO when either RREQQQAV bit or RRSPQQAV bit is set to 0 (in the Asynchronous RX/TX interrupt acknowledge, ASYINTACK, register) will result in a queue read error. 12.6.2 Link Packet Data Formats The data formats for transmission and reception of data are shown below. The transmit format describes the expected organization for data presented to the link at the asynchronous transmit, physical response, or isochronous transmit FIFO interfaces. 12.6.2.1 Asynchronous Transmit Packet Formats These sections describe the formats in which packets need to be delivered to the queues (FIFOs) for transmission. There are four basic formats as follows: ITEM 1 FORMAT No-packet No packet data USAGE Quadlet read requests Quadlet/block write responses Quadlet write requests 2 Quadlet packet Quadlet read responses Block read requests Block write requests Block read responses 3 Block Packet Lock requests Lock responses Asynchronous streams 4 Unformatted transmit Concatenated self-ID / PHY packets TRANSACTION CODE (tCode) 4 2 0 6 5 1 7 9 Bhex Ahex Ehex
Each packet format uses several fields (see names and descriptions below). More information about these fields (not the format) can be found in the 1394 specification. Grey fields are reserved and should be set to zero values.
2000 Dec 01
27
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
Table 1. Asynchronous Transmit Fields
Field Name spd tLabel Description This field indicates the speed at which this packet is to be sent. 00=100 Mbs, 01=200 Mbs, and 10=400 Mbs. 11 = undefined This field is the transaction label, which is used to pair up a response packet with its corresponding request packet. tLabels are also used as identifiers to associate a Link data confirmation (see 12.6.2.13) with the corresponding request, response, or asynchronous stream packet. Only value 01 = retryX is supported. The transaction code for this packet. Contains a node ID value. The concatenation of these two field addresses a quadlet in the destination node's address space. Response code for write response packet. rCode Meaning 0 Node successfully completed requested operation. 1-3 Reserved 4 Resource conflict detected by responding agent. Request may be retried. 5 Hardware error. Data not available. 6 Field within request packet header contains unsupported or invalid value. 7 Address location within specified node not accessible. 8-Fh Reserved A channel allocated from the isochronous manager register CHANNELS_AVAILABLE. Used only for Asynchronous stream transmit fields. Values supplied, as appropriate by the user fields supplied appropriate, user. For responses, priority is set to 0000 if fair arbitration is to be used and to 0001 if priority arbitration is to be used, as allowed by the 1394a supplement to Std IEEE 1394-1995. For quadlet write requests and quadlet read responses, this field holds the data to be transferred. The number of bytes requested in a block read request. The number of bytes of data to be transmitted in this packet The tCode indicates a lock transaction, this specifies the actual lock action to be performed with the data in this packet. The data to be sent. If dataLength=0, no data should be written into the FIFO for this field. Regardless of the destination or source alignment of the data, the first byte of the block must appear in the high order byte of the first quadlet. If the dataLength mod 4 is not zero, then zero-value bytes are added onto the end of the packet to guarantee that a whole number of quadlets is sent.
rt tCode DestinationID DestinationOffsetHigh DestinationOffsetLow rCode
channel tag sy priority Quadlet data Data length dataLength extendedTcode block data
padding
2000 Dec 01
28
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6.2.2 No-data Transmit The no-data transmit formats are shown in Figures 14 and 15. The first quadlet contains packet control information. The second and third quadlets contain 16-bit destination ID and either the 48-bit, quadlet aligned destination offset (for requests) or the response code (for responses).
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 spd
tLabel
rt
tCode
priority
destinationID
destinationOffsetHigh
destinationOffsetLow
SV01080
Figure 14. Quadlet Read Request Transmit Format
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 spd tLabel rt tCode priority
destinationID
rCode
SV01081
Figure 15. Quadlet/Block Write Response Packet Transmit Format
2000 Dec 01
29
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6.2.3 Quadlet Transmit Three quadlet transmit formats are shown below. In these figures: The first quadlet contains packet control information. The second and third quadlets contain 16-bit destination ID and either the 48-bit quadlet-aligned destination offset (for requests) or the response code (for responses). The fourth quadlet contains the quadlet data for read response and write quadlet request formats, or the upper 16 bits contain the data length for the block read request format.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 spd
tLabel
rt
tCode
priority
destinationID
destinationOffsetHigh
destinationOffsetLow
quadlet data
SV01082
Figure 16. Quadlet Write Request Transmit Format
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 spd
tLabel
rt
tCode
priority
destinationID
rCode
quadlet data
SV01083
Figure 17. Quadlet Read Response Transmit Format
2000 Dec 01
30
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 spd
tLabel
rt
tCode
priority
destinationID
destinationOffsetHigh
destinationOffsetLow
data length
SV01084
Figure 18. Block Read Request Transmit Format
2000 Dec 01
31
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6.2.4 Block Transmit The block transmit format is shown below, this is the generic format for reads and writes. The first quadlet contains packet control information. The second and third quadlets contain the 16-bit destination node ID and either the 48-bit destination offset (for requests) or the response code and reserved data (for responses). The fourth quadlet contains the length of the data field and the extended transaction code (all zeros except for lock transaction). The block data, if any, follows the extended transaction code.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 spd
tLabel
rt
tCode
priority
destinationID destinationOffsetLow dataLength
destinationOffsetHigh
extendedTcode
Block data
padding (if needed)
SV01085
Figure 19. Block Packet Transmit Format
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 spd tLabel rt tCode priority
destinationID
rCode
dataLength
extendedTcode
Block data
padding (if needed)
SV01086
Figure 20. Block Read or Lock Response Transmit Format
2000 Dec 01
32
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6.2.5 Unformatted Transmit The unformatted transmit format is shown in Figure 21. The first quadlet contains packet control information. The remaining quadlets contain data that is transmitted without any formatting on the bus. No CRC is appended on the packet, nor is any data in the first quadlet sent. This is used to send PHY configuration and Link-on packets. Note that the bit-inverted check quadlet must be included in the FIFO since the AV Link core will not generate it.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
spd
tLabel
00
1110
priority
unformatted packet data
SV01087
Figure 21. Unformatted Transmit Format 12.6.2.6 Asynchronous Stream Transmit The PDI1394L41 supports asynchronous stream as specified in IEEE1394.a. The asynchronous stream packet format is shown below. The first quadlet contains packet control information. The second quadlet contains datalength, tag, channel number, and synchronization code. The third quadlet contains the datalength in quadlets. The datalength can be zero for empty asynchronous stream packets.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 spd dataLength tag tLabel channel 1 1110 1010 priority sy
Block data
padding (if needed)
SV01050
Figure 22. Asynchronous Stream Packet Transmit Format When a packet conforming to this format is written to either asynchronous transmit FIFO, an asynchronous stream packet (identical on the cable to an isochronous packet) will be transmitted during the asynchronous phase of a bus cycle.
2000 Dec 01
33
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6.2.7 Asynchronous Receive Packet Formats This section describes the asynchronous receive packet formats. Four basic asynchronous data packet formats and one confirmation format exist:
Table 2. Asynchronous Data Packet Formats
ITEM 1 FORMAT No-packet No packet data USAGE Quadlet read requests Quadlet/block write responses Quadlet write requests 2 Quadlet packet Quadlet read responses Block read requests Block write requests 3 Block Packet Block read responses Lock requests Lock responses 4 5 Self-ID / PHY packet Confirmation packet Concatenated self-ID / PHY packets Confirmation of packet transmission TRANSACTION CODE 4 2 0 6 5 1 7 9 Bhex Ehex 8
Each packet format uses several fields. More information about most of these fields can be found in the 1394 specification.
Table 3. Asynchronous Receive Fields
Field Name destinationID tLabel Description This field is the concatenation of busNumbers (or all ones for "local bus") and nodeNumbers (or all ones for broadcast) for this node. This field is the transaction label, which is used to pair up a response packet with its corresponding request packet. tLables are also used as identifiers to associate a Link data confirmation (see 12.6.2.13) with the corresponding request, response, or asynchronous stream packet. The retry code of the received packet; see the 1394 specification. The transaction code for this packet. The priority level for this packet (0000 for cable environment). This is the node ID of the sender of this packet. The concatenation of these two field addresses a quadlet in this node's address space. Response code for the received packet; see the 1394 specification. For quadlet write requests and quadlet read responses, this field holds the data received. The number of bytes of data to be received in a block packet. If the tCode indicates a lock transaction, this specifies the actual lock action to be performed with the data in this packet. The data received. If dataLength=0, no data will be written into the FIFO for this field. Regardless of the destination or source alignment of the data, the first byte of the block will appear in the high order byte of the first quadlet. If the dataLength mod 4 is not zero, then zero-value bytes are added onto the end of the packet to guarantee that a whole number of quadlets is sent. Unsolicited response tag bit. This bit is set to one (1) if the received response was unsolicited. This field contains the acknowledge code that the link layer returned to the sender of the received packet. For packets that do not need to be acknowledged (such as broadcasts) the field contains the acknowledge value that would have been sent if an acknowledge had been required. The values for this field are listed in Table 4 (they also can be found in the IEEE 1394 standard). This field is used for asynchronous streams. 0000 Reserved. 0001 packet OK. 0010-1100 Reserved. 1101 Data CRC error and/or block size mismatch have been detected. 1110-1111 Reserved.
rt tCode priority sourceID destinationOffsetHigh, destinationOffsetLow rCode quadlet data dataLength extendedTcode block data padding u ackSent
status
2000 Dec 01
34
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
Table 4. Acknowledge codes
Code 0001 0010 0100 0101 0110 1101 Name ack_complete ack_pending ack_busy_X ack_busy_A ack_busy_B ack_data_error Description The node has successfully accepted the packet. If the packet was a request subaction, the destination node has successfully completed the transaction and no response subaction shall follow. The node has successfully accepted the packet. If the packet was a request subaction, a response subaction will follow at a later time. This code shall not be returned for a response subaction. The packet could not be accepted. The destination transaction layer may accept the packet on a retry of the subaction. The packet could not be accepted. The destination transaction layer will accept the packet when the node is not busy during the next occurrence of retry phase A. The packet could not be accepted. The destination transaction layer will accept the packet when the node is not busy during the next occurrence of retry phase B. The node could not accept the block packet because the data field failed the CRC check, or because the length of the data block payload did not match the length contained in the dataLength field. This code shall not be returned for any packet that does not have a data block payload. A field in the request packet header was set to an unsupported or incorrect value, or an invalid transaction was attempted (e.g., a write to a read-only address). This revision of the AV Link will not generate other acknowledge codes, but may receive them from newer (1394 A) links. In that case, these new values will show up here.
1110 0000, 0011, 0111 - 1100, and 1111
ack_type_error reserved
2000 Dec 01
35
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6.2.8 No-data Receive The no-data receive formats are shown below. The first quadlet contains the destination node ID and the rest of the packet header. The second and third quadlet contain 16-bit source ID and either the 48-bit, quadlet-aligned destination offset (for requests) or the response code (for responses). The last quadlet contains packet reception status.
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
destinationID
tLabel
rt
tCode
priority
sourceID
destinationOffsetHigh
destinationOffsetLow
spd
ackSent
SV00257
Figure 23. Quadlet Read Request Receive Format
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 destinationID tLabel rt tCode priority
sourceID
rCode
spd
u
ackSent
SV00258
Figure 24. Write Response Receive Format
2000 Dec 01
36
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6.2.9 Quadlet Receive The quadlet receive formats are shown below. The first quadlet contains the destination node ID and the rest of the packet header. The second and third quadlets contain 16-bit source ID and either the 48-bit, quadlet-aligned destination offset (for requests) or the response code (for responses). The fourth quadlet is the quadlet data for read responses and write quadlet requests, and is the data length and reserved for block read requests. The last quadlet contains packet reception status.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
destinationID
tLabel
rt
tCode
priority
sourceID
destinationOffsetHigh
destinationOffsetLow
quadlet data
spd
ackSent
SV00259
Figure 25. Quadlet Write Request Receive Format
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
destinationID
tLabel
rt
tCode
priority
sourceID
rCode
quadlet data
spd
u
ackSent
SV00260
Figure 26. Quadlet Read Response Receive Format
2000 Dec 01
37
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
destinationID
tLabel
rt
tCode
priority
sourceID
destinationOffsetHigh
destinationOffsetLow
data length
spd
ackSent
SV00261
Figure 27. Block Read Request Receive Format
2000 Dec 01
38
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6.2.10 Block receive The block receive format is shown below. The first quadlet contains the destination node ID and the rest of the packet header. The second and third quadlets contain 16-bit sourceID and either the 48-bit destination offset (for requests) or the response code and reserved data (for responses). The fourth quadlet contains the length of the data field and the extended transaction code (all zeros except for lock transactions). The block data, if any, follows the extended code. The last quadlet contains packet reception status.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
destinationID
tLabel
rt
tCode
priority
sourceID
destinationOffsetHigh
destinationOffsetLow
dataLength
extendedTcode
Block data
padding (if needed)
spd
ackSent
SV00262
Figure 28. Block Write or Lock Request Receive Format
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
destinationID
tLabel
rt
tCode
priority
sourceID
rCode
dataLength
extendedTcode
Block data
padding (if needed)
spd
u
ackSent
SV00263
Figure 29. Block Read or Lock Response Receive Format
2000 Dec 01
39
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6.2.11 Asynchronous Stream Receive The Asynchronous streaming receive packet format is shown below. The first quadlet contains dataLength, tag, and Channel number for source identification, and synchronization information. The following quadlets contain (possibly zero) quadlets of block information. The last quadlet contains transmission speed and status information. Asynchronous stream packets are placed in the Receive Response FIFO. Note: Due to the fact that an asynchronous stream packet is a type of isochronous packet, the STRICTISOCH bit (bit 12 in register 0x004) must be set to "0" for correct operation.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 dataLength tag chanNum 10102 sy
Block data (possibly zero)
spd
status
SV01052
12.6.2.12 Self-ID and PHY packets receive The self-ID and PHY packet receive formats are shown below. The first quadlet contains a synthesized packet header with a tCode of 0xE (hex). For self-ID information, the remaining quadlets contain data that is received from the time a bus reset ends to the first subaction gap. This is the concatenation of all the self-ID packets received. Note that the bit-inverted check quadlet is included in the Read Request FIFO and the application must check it.
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 11102 00002
self ID packet data
00
ackSent
SV00264
Figure 30. Self-ID Receive Format The "ackSent" field will either be "ACK_DATA_ERROR" if a non-quadlet-aligned packet is received or there was a data overrun, or "ACK_COMPLETE" if the entire string of self-ID packets was received.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 11102 00002
PHY packet first quadlet
SV00265
Figure 31. PHY Packet Receive Format For PHY packets, there is a single following quadlet which is the first quadlet of the PHY packet. The check quadlet has already been verified and is not included.
2000 Dec 01
40
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.6.2.13 Link data confirmation formats After a request, response, or asynchronous stream packet is transmitted, the asynchronous transmitter assembles a Link data confirmation (see Figure 32) which is used to confirm the transmission to the higher layers. Packets transmitted from the Transmit Request FIFO are confirmed by a confirmation written into the Receive Request FIFO and packets transmitted from the Transmit Response FIFO are confirmed by a confirmation written into the Receive Response FIFO. Outgoing packets and their confirmations are associated by their tLabels. It is the user's responsibility to assure the uniqueness of active tLabels.
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
tLabel
01
1000
conf
SV01051
Figure 32. Request and response confirmation format
Table 5. Confirmation codes
CODE1 0 1 2 4 D16 DESCRIPTION Non-broadcast packet transmitted; addressed node returned no acknowledge (transaction complete). Broadcast packet transmitted or non-broadcast packet transmitted; addressed node returned an acknowledge complete (transaction complete). Non-broadcast packet transmitted; addressed node returned an acknowledge pending. Retry limit exceeded; destination node hasn't accepted the non-broadcast packet within the maximum number of retries (transaction complete). Acknowledge data error received (transaction complete).
E16 Acknowledge type error received (transaction complete). NOTE: 1. All other codes are reserved.
12.7 Interrupts
The PDI1394L41 provides a single interrupt line (HIF INTN) for connection to a host controller. Status indications from five major areas of the device are collected and ORed together to activate HIF INTN. Status from four major areas of the device are collected in five status registers; LNKPHYINTACK, ITXINTACK, IRXINTACK, ASYINTACK and RDI. At this level, each individual status can be enabled to generate a chip-level interrupt by activating HIF INTN. To aid in determining the source of a chip-level interrupt, the major area of the device generating an interrupt is indicated in the lower 4 bits of the GLOBCSR register. These bits are non-latching Read-Only status bits and do not need to be acknowledged. To acknowledge and clear a standing interrupt, the bit in LNKPHYINTACK, ITXINTACK, IRXINTACK, ASYINTACK or RDI causing the interrupt status has to be written to a logic `1'; Note: Writing a value of `0' to the bit has no effect. 12.7.1 Determining and Clearing Interrupts When responding to an interrupt event generated by the PDI1394L41, or operating in polled mode, the first register examined is the RDI register. Since the addition of the RDI register (at 0x0b0), it will be necessary to first interrogate the RDI register independent of the GLOBCSR register in order to locate the source of an interrupt. Embedded software should be built to perform this function. It is recommended that this interrogation take place BEFORE the read of the GLOBCSR register is accomplished. The reason for this added step stems from the fact that none of the other link registers can be accurately read if the link is in power-down mode. If an attempt to read the GLOBCSR is made during link power-down, a quadlet will be read, but the quadlet data will not be the contents of the GLOBCSR. Once it has been determined that the interrupt was not a result of a bit setting in the RDI register, the GLOBCSR register should be tested next. The least significant nibble contains interrupt status bits from general sections of the device; the link layer controller, the AV transmitter, the AV receiver, and the asynchronous transceiver. The bits in GLOBCSR[3:0] are self clearing status bits. They represent the logical OR of all the enabled interrupt status bits in their section of the AV Link Layer Controller. Once an interrupt, or status is detected in GLOBCSR, the appropriate interrupt status register needs to be read, see the Interrupt Hierarchy diagram for more detail. After all the interrupt indications are dealt with in the appropriate interrupt status register, the interrupt status indication will automatically clear in the GLOBCSR. All interrupt status bits in the various interrupt status registers are latching unless otherwise noted.
2000 Dec 01
41
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
12.7.1.1 Interrupt Hierarchy
HIF INT_N
3 ASYTX/RX
21 ITXINT IRXINT
0 LNKPHYINT GLOBCSR (0x018)
21 20 18 17 16 15 14 13 10 9 8 7 6 5 4 3 2 1 0 PHYRST ITBADFMT ATBADFMT SNT_REJ HDRERR TCERR CYTMOUT CYSEC CYSTART AUTH DN TIMER CMDRST FAIRGAP ARBGAP CYDONE CYPEND CYLOST PHYINT PHYRRX LNKPHYINTACK (0x008)
14 13 12 10 9 8 7 6 5 4 3 2 1 0 CRCERR CIPTAGFLT RCVBP SQOV ITXFULL ITXEMPTY SYTOVF IRO/E IREMI IR100LFT IR256LFT IR512LFT IRXFULL IRXEMPTY FSYNC SEQERR
IRXINTACK (0x04C)
14 13 12 9 8 7 6 5 4 3 2 1 0 M6 ERROR ITO/E TRMBP DBCERR INPERR DISCARD ITEMI IT100LFT IT256LFT IT512LFT TRMSYT ITXINTACK (0x02C)
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RREQQFULL SIDQAV RRSPQLASTQ RREQQLASTQ RRSPQRDERR RREQQRDERR RRSPQQAV RREQQQAV TIMEOUT RCVDRSP TRSPQFULL TREQQFULL TRSPQWRERR TREQQWRERR TRSPQWR TREQQWR RRSPQFULL
ASYINTACK (0x0A0)
SV01858
NOTE: 1. A read of the RDI register (0xB0) should be done before looking for an interrupt in the GLOBCSR register. Figure 33. Interrupt Hierarchy
13.0 REGISTER MAP
Registers are 32 bits (quadlet) wide and all accesses are always done on a quadlet basis. This means that it is not possible to write just the lower 8 bits, and leave the other bits unaffected (see Section 12.5.2 for more information). The values written to undefined fields/bits are ignored and thus DON'T CARE. A full bitmap of all registers is listed in Table 6. The meaning of shading and bit cell values is as follows: A bit/field with no name written in it and dark shading is reserved and not used. A bit/field with a name in it and light shading is a READ ONLY (status) bit/field. A one bit value (0 or 1) written at the bottom of a writable (control) bit is the default value after power-on-reset.
Table 6. Full Bitmap of all Registers (consists of four tables shown on the following pages)
2000 Dec 01
42
2000 Dec 01
REGISTER ADDRESS 0x008 0x020 0x018 0x014 0x010 0x000 0x00C 0x024 IDREG CYCTM TIMER 0x01C LNKCTL 0x004 ITXHQ2 ITXHQ1 PHYACS GLOBCSR ITXPKCTL LNKPHYINTACK LNKPHYINTE 31 0 0 0 TMGOSTOP 0 0 0 1 TMCONT 0 0 TMBRE 0 BSYCTRL 0 WRPHY RCVSELFID RDPHY IDVALID 0 0 AUDIO 0 TXAP_CLK 0 0 0 0 0 0 0 1 BUS ID CYCLE_SECONDS 0 0 TxENABLE 1 RxENABLE 24 0 PHYRGAD 0 0 0 0 0 0 23 0 0 0 P DATAINV P LTLEND 0 0 AUTH DN 0 TIMER RST Tx 0 RST Rx 0 0 00 0 0 0 0 TRDEL EAUTH DN ETIMER 0 0 0 0 0 0 0 0 0 0 0 0 DBS 0 0 0 PHYRGDATA 0 0 NODE ID 0 0 0 0 0 0 0 ENOUTAV2 0 0 0 ENOUTAV1 0 0 DIRAV1 0 ECMDRST EFAIRGAP 0 EARBGAP 0 EPHYINT 0 EPHYRRX 0 EPHYRST 0 CMDRST 0 FAIRGAP 16 0 ARBGAP 0 0 PHYINT 0 PHYRRX 0 PHYRST 0 STRICTISOCH 0 0 CYMASTER 0 0 0 0 EITBADFMT 0 0 EATBADFMT 0 0 ESNT_REJ 0 0 EHDRERR ETCERR 00 00 ECYTMOUT 0 0 ECYSEC 0 0 ASYTX/RX ITXINT IRXINT LNKIPHYINT 0 ECYSTART 0 0 ECYDONE 0 0 ECYPEND 0 0 ECYLOST ITBADFMT 0 ATBADFMT 0 SNT_REJ 0 HDRERR 0 TCERR 00 CYTMOUT 0 CYSEC 0 CYSTART 0 CYDONE 0 CYPEND 0 CYLOST TxRDY ROOT BUSYFLAG CYSOURCE 0 CYTMREN RPL 0 0 CYCLE_NUMBER 0 0 0 0 0 1 15 0 0 0 FN 0
0x028
0x02C
Philips Semiconductors
ITXINTACK
ITXINTE
0x030
0
0
FMT
0
0
0
0
0
0
0
0
FDF
0
0
1394 content protection AV link layer controller
43
0 0 0 0 0 0 0 0 0 0 0 QPC 0 PRELOAD MAXBL 0 0 0 EASYTX/RX EITXINT EIRXINT ELNKPHYINT 0 0 0 0 SPH 0 0 0 PHYRXAD 0 0 0 0 0 ENXTMSTP 0 SYT_DELAY 0 0 0 0 EN_ITX 0 PM 0 0 CYCLE_OFFSET PHYRXDATA 0 0 0 0 EN_FS RST_ITX 1
0
0
0
0
0
0
EM6 ERROR
M6 ERROR
0
0
0
PART CODE
0
EITO/E
ITO/E
0
0
0
0
EITEMI
ITEMI
0
0
0
0
1
0
0
0
EIT100LFT
IT100LFT
8
0
0
0
0
EIT256LFT
IT256LFT
7
0
SYT
0
0
0
EIT512LFT
IT512LFT
0
ETRMSYT
TRMSYT
00
00
00
0
ETRMBP
TRMBP
0
VERSION CODE
0
0
0
EDBCERR
DBCERR
0
0
0
0
EINPERR
INPERR
ATACK
0
0
0
0
EDISCARD
DISCARD
0
0
0
1
EITXFULL
ITXFULL
0
0
0
0
0
PDI1394L41
Preliminary specification
SV01859
EITXEMPTY
ITXEMPTY
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
REGISTER ADDRESS ITXCTL 0x034
31
24
23 CPHR_EN
16
15
8
7 ODD/EVEN ITXM5AV 0 EN_FS RCVBP 0 ERCVBP 0 ODD/EVEN 0 IRXM5AV
0
TAG
CHANNEL
SPD
EMI
0
0
0
0
0
0
0
0 ITXM100LFT
0 ITXM256LFT
0 ITXM512LFT
0
0
0
ITXMEM 0x038
ITXMAF
0x03C
RXAP_CLK
DIS_TSC
RMVUAP
ITXMF
EN_IRX
IRXPKCTL 0x040 0 IRXHQ1 E0 0x044 F0
SNDIMM
0
0
0
1
SPAV
BPAD 0 0
0
1
SID
DBS
FN
QPC
IRXHQ2 E1 F1 0x048 FMT FDF SYT
SPH
IR100LFT
IR256LFT
IR512LFT
SEQERR
CRCERR
IRXFULL
SYTOVF
IRXINTACK 0x04C
IRXEMPTY
CIPTAGFLT
FSYNC
IREMI
IRO/E
0 ESYTOVF IRXINTE 0x050
0
0
0 EIR100LFT
0 EIR256LFT
0 EIR512LFT
0 EIRXFULL
0 EIRXEMPTY
0
0 ESEQERR
0 ECRCERR
0 ECIPTAGFLT
EIREMI
EFSYNC
EIRO/E
0 IRXCTL 0x054 DECPHR_EN
0
0
0
0
0
0
0
0
0
0
0
EMI
0
0
0
0
0
0
0
0 IRXM100LFT IRXM256LFT IRXM512LFT
0
IRXMAF
IRXMEM 0x058
0x05C . . . 0x07C
IRXMF
SV01860
2000 Dec 01
44
IRXME
SY
SPD
TAG
CHANNEL
ERR
ESQOV 0
SQOV 0
RST_IRX
ITXME
SY
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
DIS_BCAST
REGISTER ADDRESS ASYCTL 0x080
31
24 23 ARXRST
16 15
8
7
0
ATXRST
ARXALL
MAXRC
TOS
TOF
0 ASYMEM 0x084
0
1
1
0
0
0 TRSPQIDLE
0 TREQQIDLE
0
0 RRSPQAF
0 RRSPQ5AV
0
0
0 RREQQAF
1 RREQQ5AV
1
0
01 TRSPQ5AV
0
0
0
0 TREQQ5AV TRSPQWR 0 ETRSPQWR 0 SCA 0
0
TREQQAF
TRSPQAF
RREQQE
RREQQF
RRSPQE
RRSPQF
TX_RQ_NEXT 0x088
FIRST/MIDDLE QUADLET OF PACKET FOR TRANSMITTER REQUEST QUEUE (WRITE ONLY)
TX_RQ_LAST 0x08C
LAST QUADLET OF PACKET FOR TRANSMITTER REQUEST QUEUE (WRITE ONLY)
TX_RP_NEXT 0x090
FIRST/MIDDLE QUADLET OF PACKET FOR TRANSMITTER RESPONSE QUEUE (WRITE ONLY)
TX_RP_LAST 0x094
LAST QUADLET OF PACKET FOR TRANSMITTER RESPONSE QUEUE (WRITE ONLY)
RREQ 0x098
QUADLET OF PACKET FROM RECEIVER REQUEST QUEUE (TRANSFER REGISTER)
RRSP 0x09C
QUADLET OF PACKET FROM RECEIVER RESPONSE QUEUE (TRANSFER REGISTER)
RREQQRDERR
RRSPQRDERR
RREQQLASTQ
RREQQFULL
RRSPQLASTQ
TREQQWRERR
RRSPQFULL
RREQQQAV
TREQQFULL
TRSPQWRERR
RRSPQQAV
TRSPQFULL
0x0A0
0 ERRSPQFULL
0 ERREQQFULL
0
0 ERRSPQLASTQ
0 ERREQQLASTQ
0 ERRSPQRDERR
0 ERREQQRDERR
0 ERRSPQQAV
0
TIMEOUT
ASYINTACK
0
00 ETRSPQFULL
0 ETREQQFULL
0 ETRSPQWRERR
0 ETREQQWRERR
ERREQQQAV
0x0A4
0 0x0A8 0x0AC
0
0
ESIDQAV
ASYINTE
0
0
0
0
0
0
0
ERCVDRSP
0
0
0
0
0
0
LPSTAT
SWPD
RDI 0x0B0
ESCA
ELOA
ESCI
EPLI
LOA
0
0
0
0
0
0
0
0
SCI 0
PLI
ETREQQWR
ETIMEOUT
TREQQWR 0
RCVDRSP
SIDQAV
TREQQE
TREQQF
TRSPQE
TRSPQF
SV01861
2000 Dec 01
45
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
REGISTER ADDRESS
31
24 23
16 15
8
7
0
0x0B4 . . . . 0x0F0
SHADOW_REG 0x0F4 0 0 0
byte 0
byte 1
byte 2
byte 3
0
1
1
1
1
0
0
0
0
1
0
1
0
0
0
0
0
0
1
0
1
0
0
0
0
0
0
0
0
INDADDR 0x0F8
RESERVED
INDADDR
INDDATA 0x0FC
WINDOW TO THE INDIRECT QUADLET POINTED TO BY INDADDR
SV01033
2000 Dec 01
46
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.1 Link Control Registers
13.1.1 ID Register (IDREG) - Base Address: 0x000 The ID register is automatically updated by the attached PHY with the proper Node ID after completion of the bus reset.
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BUS ID
NODE ID
PART CODE
VERSION CODE
SV00915
Reset Value 0xFFFF0202 Bit 31..22: R/W BUS ID: The 10-bit bus number that is used with the Node ID in the source address for outgoing packets and used to accept or reject incoming packets. This field reverts to all `1's (0x3FF) upon bus reset. Bit 21..16: R/W NODE ID: Used in conjunction with Bus ID in the source address for outgoing packets and used to accept or reject incoming packets. This register auto-updates with the node ID assigned after the 1394 bus Tree-ID sequence. Bit 15..8: R PART CODE: "02" designates PDI1394L41. Bit 7..0: R VERSION CODE: "02" shows this is revision level 2 of this part.
13.1.2 General Link Control (LNKCTL) - Base Address: 0x004 The General Link control register is used to program the Link Layer isochronous transceiver, as well as the overall link transceiver. It also provides general link status.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 STRICTISOCH RCVSELFID CYMASTER CYSOURCE CYTMREN BUSYFLAG TxENABLE RxENABLE
IDVALID
RST Rx
RST Tx
TxRDY ROOT
BSYCTRL
DATAINV LTLEND
ATACK
RPL
SV00892
Reset Value 0x46000002 Bit 31: R/W IDValid (IDVALID): When equal to one, the PDI1394L41 accepts the packets addressed to this node. This bit is automatically set after selfID complete and node ID is updated. Bit 30: R/W Receive Self ID (RCVSELFID): When asserted, the self-identification packets, generated by each PHY device on the bus, during bus initialization are received and placed into the asynchronous request queue as a single packet. Bit 30 also enables the reception of PHY configuration packets in the asynchronous request queue. Bit 29..27: R/W Busy Control (BSYCTRL): These bits control what busy status the chip returns to incoming packets. The field is defined below: 000 = use protocol requested by received packet (either dual phase or single phase) 001 = RESERVED 010 = RESERVED 011 = use single phase retry protocol 100 = use protocol requested in packet, always send a busy ack (for all packets) 101 = RESERVED 110 = RESERVED 111 = use single phase retry protocol, always send a busy ack Bit 26: R/W Transmitter Enable (TxENABLE): When this bit is set, the link layer transmitter will arbitrate and send packets. Bit 25: R/W Receiver Enable (RxENABLE): When this bit is set, the link layer receiver will receive and respond to bus packets. Bit 23: R Data Invariant (DATAINV) refers to the byte ordering of data being presented to the Link through the host interface (HIF) port and the handling of the address and data lines by the link chip. When DATAINV = 0, the Link is in address invariant mode. When DATAINV = 1, the Link is in data invariant mode. This bit is only important if the LTLEND (Little Endian) bit is set (1), otherwise it is ignored. Interpretation of address and data information varies with the settings of these bits and with the data format being presented. See the section on Big and Little Endian Modes for more information (Section 12.5.4).
2000 Dec 01
47
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
Bit 22:
R
Bit 21: Bit 20: Bit 18:
R/W R/W R/W
Bit 12:
R/W
Bit 11:
R/W
Bit 10: Bit 9: Bit 6: Bit 5: Bit 4: Bit 3..0:
R/W R/W R R R R
Little Endian (LTLEND): Refers to the state of the endianess of the data and address lines connected to the 'L41. This bit reflects the state of the AV2ERR0/LTLEND pin during power reset. The state of this pin is read during reset and that state is latched into this bit position. When LTLEND = 0, the chip is set to receive BIG ENDIAN address and data on its host interface (HIF). When LTLEND = 1, the Link chip will receive LITTLE ENDIAN oriented data and address information. If this bit is set (1), the state of the DATAINV pin will also become important for determination of data positions in the internal link registers. See the section on Big and Little Endian Modes for more information (Section 12.5.4). Reset Transmitter (RSTTx): When set to one, this synchronously resets the transmitter within the link layer. Reset Receiver (RSTRx): When set to one, this synchronously resets the receiver within the link layer. Reset PHY-Link interface (RPL): Resets the PHY-Link interface in accordance with 1394a requirements. Note: This bit automatically resets to "0" when the interface reset operation has been completed. The PHY-Link reset operation occurs very quickly, reading this bit accurately is not usually possible. Before asserting the RPL bit, SWPD or setting the PD pin high, the user should assure that the link chip is in the following state of operation: 1) The isochronous transmit FIFO is not receiving data for transmission 2) The isochronous transmitter is disabled 3) No asynchronous packets are being generated for transmission 4) Both the ASYNC request and response queues are empty Strict Isochronous (STRICTISOCH): Used to accept or reject isochronous packets sent outside of specified isochronous cycles (between a Cycle Start and subaction gap). A `1' rejects packets sent outside the specified cycles, a "0" accepts isochronous packets sent outside the specified cycle. Cycle Master (CYMASTER): When asserted and the PDI1394L41 is attached to the root PHY (ROOT bit = 1), and the cycle_count field of the cycle timer register increments, the transmitter sends a cycle-start packet. Cycle Master function will be disabled if a cycle timeout is detected (CYTMOUT bit 5 in LNKPHYINTACK). To restart the Cycle Master function in such a case, first reset CYMASTER, then set it again. Cycle Source (CYSOURCE): When asserted, the cycle_count field increments and the cycle_offset field resets for each positive transition of CYCLEIN. When deasserted, the cycle count field increments when the cycle_offset field rolls over. Cycle Timer Enable (CYTIMREN): When asserted, the cycle offset field increments. When deasserted, the Cycle Timer Register (0x010, CYCTM) can be used as a general read write register for Host Interface Firmware testing. Transmitter Ready (TxRDY): The transmitter is idle and ready. Root (ROOT): Indicates this device is the root on the bus. This automatically updates after the self_ID phase. Busy Flag (BUSYFLAG): The type of busy acknowledge which will be sent next time an acknowledge is required. 0 = Busy A, 1 = Busy B (only meaningful during a dual-phase busy/retry operation). AT acknowledge received (ATACK): The last acknowledge received by the transmitter in response to a packet sent from the transmit-FIFO interface while the ATF is selected (diagnostic purposes).
2000 Dec 01
48
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.1.3 Link /Phy Interrupt Acknowledge (LNKPHYINTACK) - Base Address: 0x008 The Link/Phy Interrupt Acknowledge register indicates various status and error conditions in the Link and Phy which can be programmed to generate an interrupt. The interrupt enable register (LNKPHYINTE) is a mirror of this register. Acknowledgment of an interrupt is accomplished by writing a `1' to a bit in this register that is set. This action reset the bit indication to a `0'. Writing a `1' to a bit that is already "0" will have no effect on the register.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ITBADFMT ATBADFMT SNT_REJ HDRERR TCERR CYTMOUT CYSEC CYSTART CYDONE CYPEND CYLOST AUTH DN TIMER CMDRST FAIRGAP ARBGAP PHYINT PHYRRX PHYRST
SV01040
Reset Value 0x00000000 Bit 21: R/W Authentication Acceleration Done (AUTH DN). The authentication accelerator has finished an operation. Check the status of `Valid' in the Authentication Accelerator indirect register. Bit 20: R/W Timer (TIMER): When TIMER = 1, this bit indicates that the timer has counted down to zero. This interrupt may occur only once or may occur repeatedly, according to the setting of the TMCONT bit in the TIMER register. Acknowledge this interrupt by writing a "1" back into this bit position. Bit 18: R/W Command Reset Received (CMDRST): A write request to RESET-START has been received. Bit 17: R/W Fair Gap (FAIRGAP): The serial bus has been idle for a fair-gap time (called subaction gap in the IEEE 1394 specification). Bit 16: R/W Arbitration Reset Gap (ARBGAP): The serial bus has been idle for an arbitration reset gap. Bit 15: R/W Phy Chip Int (PHYINT): The Phy chip has signaled an interrupt through the Phy interface after a bus reset or PHY reset. This bit becomes active for any of the following reasons (1) PHY has detected a loop on the bus, (2) cable power has fallen below the minimum voltage, (3) the PHY arbitration state machine has timed-out usually indicative of a bus loop, (4) a bus cable has been disconnected. Typically, recognition and notification of any of the above events by the PHY requires between 166 and 500 microseconds; therefore, this bit is not instantaneously set. Bit 14: R/W Phy Register Information Received (PHYRRX): A register has been transferred by the Physical Layer device into the Link. Bit 13: R/W Phy Reset Started (PHYRST): A Phy-layer reconfiguration has started. This interrupt clears the ID valid bit. (Called Bus Reset in the IEEE 1394 specification). The Async queues will be flushed during a bus reset. Bit 10: R/W Isochronous Transmitter is Stuck (ITBADFMT): The transmitter has detected invalid data at the transmit-FIFO interface when the isochronous transmit FIFO is selected. Reset the isochronous transmitter to clear. Bit 9: R/W Asynchronous Transmitter is Stuck (ATBADFMT): The transmitter expected start of new async packet in queue, but found other data (out of sync with user). Reset the asynchronous transmitter to clear. Bit 8: R/W Busy Acknowledge Sent by Receiver (SNT_REJ): The receiver was forced to send a busy acknowledge to a packet addressed to this node because the receiver response/request FIFO overflowed. Bit 7: R/W Header Error (HDRERR): The receiver detected a header CRC error on an incoming packet that may have been addressed to this node. Bit 6: R/W Transaction Code Error (TCERR): The transmitter detected an invalid transaction code in the data at the transmit FIFO interface. Bit 5: R/W Cycle Timed Out (CYTMOUT): ISOCH cycle lasted more than 125s from Cycle-Start to Fair Gap: Disables cycle master function Bit 4: R/W Cycle Second incremented (CYSEC): The cycle second field in the cycle-timer register incremented. This occurs approximately every second when the cycle timer is enabled. Bit 3: R/W Cycle Started (CYSTART): The transmitter has sent or the receiver has received a cycle start packet. Bit 2: R/W Cycle Done (CYDONE): A fair gap has been detected on the bus after the transmission or reception of a cycle start packet. This indicates that the isochronous cycle is over; Note: Writing a value of `0' to the bit has no effect. Bit 1: R/W Cycle Pending (CYPEND): Cycle pending is asserted when cycle timer offset is set to zero (rolled over or reset) and stays asserted until the isochronous cycle has ended. Bit 0: R/W Cycle Lost (CYLOST): The cycle timer has rolled over twice without the reception of a cycle start packet. This only occurs when cycle master is not asserted.
2000 Dec 01
49
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.1.4 Link / Phy Interrupt Enable (LNKPHYINTE) - Base Address: 0x00C This register is a mirror of the Link/Phy Interrupt Acknowledge (LNKPHYINTACK) register. Enabling an interrupt is accomplished by writing a `1' to the bit corresponding to the interrupt desired. This register enables the interrupts described in the Link /Phy Interrupt Acknowledge register (LNKPHYINTACK) description. A one in any of the bits enables that function to create an interrupt. A zero disables the interrupt, however the status is readable in the Link /Phy Interrupt Acknowledge register.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 EITBADFMT EATBADFMT ESNT_REJ EHDRERR ETCERR ECYTMOUT ECYSEC ECYSTART ECYDONE ECYPEND ECYLOST EAUTH DN ECMDRST EFAIRGAP EARBGAP EPHYINT EPHYRRX EPHYRST
ETIMER
SV00894
Reset Value 0x00000000 Bits 21..0 are interrupt enable bits for the Link/Phy Interrupt Acknowledge (LNKPHYINTACK). 13.1.5 Cycle Timer Register (CYCTM) - Base Address: 0x010 Cycle Timer Register operation is controlled by the Cycle Timer Enable (CYTMREN) bit in the Link Control Register (LNKCTL, 0x004). If the Cycle Timer Register is disabled, it can be used as a general read write register for Host Interface Firmware testing.
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CYCLE_SECONDS
CYCLE_NUMBER
CYCLE_OFFSET
SV00276
Reset Value 0x00000000 Bit 31..25: R/W Seconds count: 1-Hz cycle timer counter. Bit 24..12: R/W Cycle Number: 8kHz cycle timer counter. Bit 11..0: R/W Cycle Offset: 24.576MHz cycle timer counter.
2000 Dec 01
50
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.1.6 Phy Register Access (PHYACS) - Base Address: 0x014 This register provides access to the internal registers on the Phy. There are special considerations when reading or writing to this register. When reading a PHY register, the address of the register is written to the PHYRGAD field with the RDPHY bit set. The PHY data will be valid when the PHYRRX bit (LNKPHYINTACK register bit 14) is set. Once this happens the register data is available in the PHYRXDATA, the address of the register just read is also available in the PHYRXAD fields. When writing a Phy register, the address of the register to be written is set in the PHYRGAD field and the data to be written to the register is set in PHYRGDATA, along with the WRPHY bit being set. Once the write is complete, the WRPHY bit will be cleared. Do not write a new Read/Write command until the previous one has been completed. After the Self-ID phase, PHY register 0 will be read automatically.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RDPHY WRPHY PHYRGAD PHYRGDATA PHYRXAD PHYRXDATA
SV00277
Reset Value 0x00000000 Bit 31: R/W Read Phy Chip Register (RDPHY): When asserted, the PDI1394L41 sends a read register request with address equal to Phy Rg Ad to the Phy interface. This bit is cleared when the request is sent. Bit 30: R/W Write Phy Chip Register (WRPHY): When asserted, the PDI1394L41 sends a write register request with address equal to Phy Rg Ad to the Phy interface. This bit is cleared when the request is sent. Bit 27..24: R/W Phy Chip Register Address (PHYRGAD): This is the address of the Phy-chip register that is to be accessed. Bit 23..16: R/W Phy Chip Register Data (PHYRGDATA): This is the data to be written to the Phy-chip register indicated in Phy Rg Ad. Bit 11..8: R Phy Chip Register Received Address (PHYRXAD): Address of register from which Phy Rx Data came. Bit 7..0: R Phy Chip Register Received Data (PHYRXDATA): Data from register addressed by Phy Rx Ad. 13.1.7 Global Interrupt Status and TX Control (GLOBCSR) - Base Address: 0x018 This register is the top level interrupt status register. If the external interrupt line is set, this register will indicate which major portion of the AV Link generated the interrupt. There is no interrupt acknowledge required at this level. These bits auto clear when the interrupts in the appropriate section of the device are cleared or disabled. Control of the AV transceiver is also provided by this register. Bits 0 to 3 are used to identify which internal modules are currently generating an interrupt. After identifying the module, the appropriate register in that module must be read to determine the exact cause of the interrupt. A timer is available to aid the implementation of higher level protocols such as AV/C and HAVi. The timer can be started and stopped, and automatically reloads with 1s (TIMLOAD = 1) or 100ms (TIMLOAD = 0). When the set time has expired, an interrupt will be generated through TIMER (Bit 20, LNKPHYINTACK 0x008). In normal timer mode (TIMMODE = 0), the timer will generate an interrupt, reload and restart every time it expires, until TIMRNSTP is cleared. In bus reset timer mode (TIMMODE = 1), even when already running the timer will reload with 1s and restart automatically after a bus reset. If another bus reset occurs before the timer expires, the timer will again reload and restart. No interrupt will be generated until the timer expires.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 EASYTX/RX ENOUTAV2 ENOUTAV1
9
8 ELNKPHYINT
7
6
5
4
3 ASYTX/RX
2
1
0 LNKPHYINT
DIRAV1
EIRXINT
EITXINT
SV01024
NOTES 1. There can be more than one interrupt source active at the same time. 2. The HIF INT_N signal (pin 28) remains active as long as there is at least one more enabled active interrupt status bit. Reset Value 0x00010000 Bit 18: R/W Enable output AVPORT2: A `1' enables AVPORT2 as an output. A `0' sets the 3-State condition on the port. In 3-State condition the port may be used as an input or unused output according to the state of DIRAV1 (bit 16). Bit 17: R/W Enable output AVPORT1: A `1' enables AVPORT1 as an output. A `0' sets the 3-State condition on the port. In 3-State condition the port may be used as an input or unused output according to the state of DIRAV1 (bit 16).
2000 Dec 01
51
IRXINT
ITXINT
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
Bit 16:
R/W
Bit 11: Bit 10: Bit 9: Bit 8: Bit 3: Bit 2: Bit 1: Bit 0:
R/W R/W R/W R/W R R R R
Direction of AVPORT1 (DIRAV1): A `1' enables AVPORT1 as a transmitter, thus AVPORT1 pins are inputs. A `0' configures AVPORT1 as a receiver, AVPORT1 pins are outputs in this configuration. The configuration of AVPORT2 pins is opposite of AVPORT1 pins. When AVPORT1 is set to transmit, AVPORT2 receives and vice versa. Enables generation of external interrupt by asynchronous transmitter and receiver module (ASYTX/RX, bit 3) when set (1). Disables such interrupts when clear (0) (regardless of ASYINTE contents). Enables generation of external interrupt by the isochronous transmitter module (ITXINT, bit 2) when set (1). Disables such interrupts when clear (0) (regardless of ITXINTE contents). Enables generation of external interrupt by the isochronous receiver module (IRXINT, bit 1) when set (1). Disables such interrupts when clear (0) (regardless of IRXINTE contents). Enables generation of external interrupt by general link/phy module (LKPHYINT, bit 0) when set (1). Disables such interrupts when clear (0) (regardless of LNKPHYINTE contents). Asynchronous Transmitter/Receiver Interrupt (ASYITX/RX): Interrupt source is in the Asynchronous Transmitter/ Receiver Interrupt Acknowledge/Source register. AV Transmitter Interrupt (ITXINT): Interrupt source is in the AV Transmitter Interrupt Acknowledge/Source register. AV Receiver Interrupt (IRXINT): Interrupt source is in the AV Receiver Interrupt Acknowledge/Source register. Link-Phy Interrupt (LNKPHYINT): Interrupt source is in the Link Phy Interrupt Acknowledge register.
13.1.8 Timer (TIMER) - Base Address: 0x01C
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TMGOSTOP TMCONT TMBRE
PRELOAD
SV01096
Reset Value Bit 31: Bit 30: Bit 29: Bit 23..0:
R/W R/W R/W R/W
TMGOSTOP: Timer Go/Stop, when = 1 start timer; when = 0 stop timer. TMCONT: Timer Continuous, when = 1 continuously operate timer; when = 0 operate timer for one timing cycle, then stop. TMBRE: Timer Bus Reset Enable, when = 1, start the timer at the beginning of a bus reset; when = 0 start the timer from the TMGOSTOP bit setting. Timer preload bits. Load a number into the timer preload bits with the most significant bit in the higher numbered bit position; the least significant bit in the timer preload register is bit 0. The basic timing unit is 1/(2*CLK25) or 80.14 nanoseconds. The maximum timer time-out is about 1.34 seconds ((2^24)-1 units). The timer uses the preload value inputted by the host into bits 0 through 23 of this register. The preload value is placed in the actual timer/counter (invisible to outside world) and this value is decremented by 1 for each unit of time. The timer eventually counts down to zero and then it sets the TIMER interrupt flag bit in register 0x008, LINKPHYINTACK (assuming the interrupt was enabled by the ETIMER bit). Depending on the setting of the TMCONT bit in this register, the timer preload value may be automatically reloaded into the timer/counter (when TMCONT = 1) with the timing cycle automatically re-starting, or the timer will simply interrupt and stop (when TMCONT bit = 0). TMBRE adds a mode to the timer operation which starts the timing automatically at the start of a 1394 bus reset. When TMBRE is set (1), the TMGOSTOP bit function is disabled; the TMCONT bit function is still available. NOTE: When TMCONT = 1, failing to acknowledge a TIMER interrupt has no effect on the starting/restarting of the timer; if an interrupt is not acknowledged (bit reset), the timer will continue to time out and restart.
2000 Dec 01
52
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.2 AV (Isochronous) Transmitter and Receiver Registers
13.2.1 Isochronous Transmit Packing Control and Status (ITXPKCTL) - Base Address: 0x020 This register allows the user to set up the appropriate AV packets from data entered into the AV interface. The packing and control parameters (TRDEL, MAXBL, DBS, FN, QPC, and SPH) should never be changed while the transmitter is operating. The only exception to this is the MAXBL parameter when in MPEG-2 packing mode. NOTE: When reset of isochronous transmitter is necessary, first disable the transmitter (place bit 4, EN_ITX, LOW), wait for FIFO to empty, then reset the transmitter (place RST_ITX, bit 0, HIGH). This procedure will ensure that data in the FIFO is transmitted before reset.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 SYT_DELAY ENXTMSTP TXAP_CLK EN_FS RST_ITX
AUDIO
TRDEL
MAXBL
EN_ITX
PM
SV01862
Reset Value 0x00000001 Bit 30: R/W AUDIO mode bit: When = 1, SYT system is in AUDIO mode. When AUDIO = 0 normal SYT time stamping operation is assumed. With AUDIO = 1, the SYT time stamp for an FSYNC pulse will NOT be appended to an empty bus packet. Any pending SYT stamp will be held until the next non-empty bus packet is sent. As an FSYNC pulse is input to the transmitting node's link chip, an SYT stamp will be made. This SYT stamp will point to a time in the future dictated by the SYT DELAY value (in register 0x020) added to the current least significant nibble (lsn) of the cycle number, plus the current cycle offset value. This mode automatically increases SYT_DELAY value by two additional cycles beyond the value programmed in the SYT_DELAY bits. Bit 29..28: R/W TXAP_CLK: Application Clock, default mode, `00' the AVxCLK pin is an input. This pin can become an application clock for the isochronous Transmitter (and output) by programming it to `01', `10', or `11'. The programming values are: 00 Input 01 24.576MHz 10 12.288MHz 11 6.144MHz Note that when enabled as `01', `10', or `11', the AV port that is configured as transmitter and enabled will output this clock signal on its AVxCLK pin. Bit 27..16: R/W TRDEL: Transport delay. Value added to cycle timer to produce time stamps. Lower 4 bits add to upper 4 bits of cycle_offset, (Cycle Timer Register, CYCTM). Remainder adds to cycle_count field. Bit 15..8: R/W MAXBL: The (maximum) number of data blocks to be put in a payload. Bit 7: R/W ENXTMSTP: Enable External time stamp control. Allows an external time stamp (generated by the application) to be inserted in place of the link-generated time stamp. Defaults to link generated time stamp. The application must present the first byte of a quadlet-wide time stamp accompanied by the AVSYNC pulse (and AVVALID) to the AVPORT. The external time stamp quadlet is inputted first, followed by the application data packet. The transmitted packet size is now one quadlet larger than the original isochronous data packet--Set up the isochronous transmitter accordingly with SPH = 1. CAUTION: Unless valid IEC 61883 time stamp format (based on the link cycle timer) is used, the receiving node link chip must be equipped with a time stamp check disabling function similar to the DIS_TSC bit (register 0X040, Bit 7). Please see Section 13.2.8 for details. Bit 6..5: R/W SYT_DELAY: Programmable delay of AV1FSYNC and AV2FSYNC. Each cycle is 1 bus cycle, 125 ms. Reset value is "00", a 3 cycle delay. 01 = 2 cycles 00 = 3 cycles 10 = 4 cycles 11 = Reserved Bit 4: R/W EN_ITX: Enable receipt of new application packets and generation of isochronous bus packets in every cycle. This bit also enables the Link Layer to arbitrate for the transmitter in each subsequent bus cycle. When this bit is disabled (0), the current packet will be transmitted and then the transmitter will shut down. Bit 3..2: R/W PM: packing mode: 00 = variable sized bus packets, most generic mode. 01 = fixed size bus packets. 10 = MPEG-2 packing mode. 11 = No data, just CIP headers are transmitted. Bit 1: R/W EN_FS:enable generation/insertion of SYT stamps (Time Stamps) in CIP header. Bit 0: R/W Reset Isochronous Transmitter (RST_ITX): causes transmitter to be reset when `1'. In order for synchronous reset of ITX to work properly, an AVxCLK (from either the internal or external source) must be present and ensure that the reset bit is kept (programmed) HIGH for at least the duration of one AVxCLK period. Failure to do so may cause the application interface of this module to be improperly reset (or not reset at all). When reset is enabled, all bytes will be flushed from the FIFO and transmission will cease immediately. 2000 Dec 01 53
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.2.2 Common Isochronous Transmit Packet Header Quadlet 1 (ITXHQ1) - Base Address: 0x024 The AV Transmit Packing Control register holds the specification for the packing scheme used on the AV data stream. This information is included in Common Isochronous Packet (CIP) header quadlet 1.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBS
FN
QPC SPH
SV01747
Reset Value 0x00000000 Bit 16..23: R/W DBS: Size of the data blocks from which AV payload is constructed. The value 0 represents a length of 256 quadlets. Bit 14..15: R/W FN: (Fraction Number) The encoding for the number of data blocks into which each source packet shall be divided (00 = 1, 01 = 2, 10 = 4, 11 = 8). Bit 11..13: R/W QPC: Number of dummy quadlets to append to each source packet before it is divided into data blocks of the specified size. The value QPC must be less than DBS and less than 2FN. Bit 10: R/W SPH: Indicates that a 25-bit CYCTM based time stamp has to be inserted before each application packet. 13.2.3 Common Isochronous Transmit Packet Header Quadlet 2 (ITXHQ2) - Base Address: 0x028 The contents of this register are copied to the second quadlet of the CIP header and transmitted with each isochronous packet.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FMT
FDF
SYT
SV00281
Reset Value 0x00000000 Bit 29..24: R/W FMT: Value to be inserted in the FMT field in the AV header. Bit 23..0: R/W FDF/SYT: Value to be inserted in the FDF field. When the EN_FS bit in the Transmit Control and Status Register (ITXPKCTL) is set (=1), the lower 16 bits of this register are replaced by an SYT stamp if a rising edge on AVFSYNCIN has been detected or all `1's if no such edge was detected since the previous packet. The upper 8 bits of the register are sent as they appear in the FDF register. When the EN_FS bit in the Transmit Control and Status Register is unset (=0), the full 24 bits can be set to any application specified value.
2000 Dec 01
54
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.2.4 Isochronous Transmitter Interrupt Acknowledge (ITXINTACK) - Base Address: 0x02C The AV Transmitter Interrupt Control and Status register is the interrupt register for the AV transmitter. Bits 2, 3, and 4 "auto repair" themselves, i.e. AVLINK will detect the situation and attempt to recover on its own. The host controller still needs to clear these interrupts to be alerted the next time.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 M6 ERROR ITO/E ITEMI SYTTI EOTI DBCEI IDDSCI PLDSCI ITXMFI ITXMEI IT100LFT IT256LFT IT512LFT TRMSYT TRMBP DBCERR INPERR DISCARD ITXFULL ITXEMPTY
SV01054
Reset Value 0x00000000 Bit 14: R/W M6 ERROR: The M6 cipher block has encountered an unrecoverable error. Proper operation will be resumed by disabling and resetting the ITX. Bit 13: R/W ITO/E: An odd/even key change has occurred in the cipher, it is now OK to write in the new key set. Bit 12: R/W ITEMI: This bit indicates that the EMI bit value used to cipher outgoing transmission has changed. Bits 9 .. 0 are interrupt acknowledge bits; and are defined as: Bit 9: R/W IT100LFT: Interrupt when transmitter queue reaches 100 quadlets from full. Bit 8: R/W IT256LFT: Interrupt when transmitter queue reaches 256 quadlets from full. Bit 7: R/W IT512LFT: Interrupt when transmitter queue reaches 512 quadlets from full. This bit is disabled if 0.5K Byte buffer size is set. Bit 6: R/W TRMSYT: Interrupt on transmission of a SYT in CIP header quadlet 2 Bit 5: R/W TRMBP: Interrupt on payload transmission/discard complete. Bit 4: R/W DBCERR: Acknowledge interrupt on Data Block Count (DBC) synchronization loss. Bit 3: R/W INPERR: Acknowledge interrupt on input error (input data discarded). Bit 2: R/W DISCARD: Interrupt on lost cycle (payload discarded). Bit 1: R/W ITXFULL: Interrupt on isochronous memory bank full. This is a fatal error. The ITX transmitter will reset itself automatically when this occurs. Bit 0: R/W ITXEMPTY: Interrupt on isochronous memory bank empty. Other bits will always read `0'. 13.2.5 Isochronous Transmitter Interrupt Enable (ITXINTE) - Base Address: 0x030 These are the enabled bits for the AV Transmitter Control.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 EM6 ERROR EIT100LFT EIT256LFT
6
543 ETRMBP EDBCERR
21 EITXFULL
0 EITXEMPTY
Reset Value 0x00000000 Bits 13..0 are interrupt enable bits for the Isochronous Transmitter Interrupt Acknowledge register (ITXINTACK).
2000 Dec 01
55
EINPERR EDISCARD
EIT512LFT ETRMSYT
IDDSCI PLDSCI
ITXMFI
ITXMEI
EITEMI
SYTTI EOTI DBCEI
EITO/E
SV01055
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.2.6 Isochronous Transmitter Control Register (ITXCTL) - Base Address: 0x34
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ODD/EVEN SY CPHR_EN
TAG
CHANNEL
SPD EMI
SV01016
Reset Value 0x00000000 Bit 20: R/W Cipher Enable: When set, the internal M6 cipher will encrypt the application packets with the associated key in the M6 indirect address space for the given EMI value assigned. When the EMI value changes the cipher will automatically change the key on the next application packet. Writes to the ODD/EVEN bit (bit 1 will automatically swap the odd/even key in the cipher. Note: the maximum average data rate for the M6 cipher is 100 Mbps. Bit 15..14: R/W Tag: Tag code to insert in isochronous bus packet header. Should be `01' for IEC 61883 International Standard data. Bit 13..8: R/W Channel: Isochronous channel number. Bit 5..4: R/W Speed: Cable transmission speed (S100, S200, S400). 00 = 100Mbs 01 = 200Mbs 10 = 400Mbs 11 = reserved Bit 3..2 R/W Encryption Mode Indication: This bit pattern specifies the level of copy control information for the data stream. The field only has significance when the internal cipher is enabled (CPHR_EN = 1). See the "5C Digital Transmission Content Protections Specification, Volume 1" for more details about EMI values. Bit 1 R/W Odd even bit used for encryption key (0 = even, 1 = odd). When the internal M6 cipher is enabled (CPHR_EN = 1), a write that changes this bit field will cause the cipher to swap its odd/even key. The key will be changed on the very next application packet and an interrupt (ODDEVN) will be generated. See the "5C Digital Transmission Content Protection Specification, Volume 1" for more details about odd/even values. When the internal cipher is not enabled (CPHR_EN = 0) the bit value is R/W and the current bit value will be transmitted in the isochronous header. Bit 0 R SY: Sync code to insert in SY field of isochronous bus packet header. This bit reflects the value of the AVx SY pin and is synchronized with the data payload that was associated with it. 13.2.7 Isochronous Transmitter Memory Status (ITXMEM) - Base Address: 0x038 The AV Transmitter Memory Status register reports on the condition of the internal memory buffer used to store incoming AV data streams before transmission over the 1394 bus. This register is used primarily for diagnostics; several memory status flags are also available in the ITXINTACK register.
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ITXM100LFT ITXM256LFT ITXM512LFT ITXMF ITXMAF ITXM5AV ITXME
SV01056
Reset Value 0x00000003 BIT 6: R Bit 5: R Bit 4: R Bit 3: R Bit 2: R Bit 1: R Bit 0: R
ITXM100LFT: 100 or less quadlets of storage available. ITXM256LFT: Memory has 256 quadlets of space remaining before becoming full. ITXM512LFT: Memory has 512 quadlets of space remaining before becoming full. ITXMF: memory is completely full, no storage available. ITXMAF: almost full, exactly one quadlet of storage available. ITXM5AV: at least 5 more quadlets of storage available. ITXME: memory bank is empty (zero quadlets stored).
2000 Dec 01
56
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.2.8 Isochronous Receiver Unpacking Control (IRXPKCTL) - Base Address: 0x040 NOTE: When receiver reset is required, first disable receiver (EN_IRX = 0), then wait until Rx FIFO is emptied, then perform the reset. This will allow previously received packets to go to the application instead of being lost.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RXAP_CLK SNDIMM DIS_TSC RMVUAP SPAV EN_IRX EN_FS RST_IRX
BPAD
SV00887
Reset Value 0x00000041 AV Receiver Control Bits. Bit 29..28: R/W RXAP_CLK: Receiver Application Clock, default mode, `00' the AVxCLK pin is an input. This pin can become an application clock and output for the isochronous Receiver by programming it to `01', `10', or `11'. The programming values are: 00 Input 01 24.576MHz 10 12.288MHz 11 6.144MHz Note that when enabled as `01', `10', or `11', the AV port that is configured as receiver and enabled will output this clock signal on its AVxCLK pin. Bit 8: R/W SNDIMM: Send immediately; when set to "1", this bit will allow a received isochronous packet containing a CRC error to be output immediately (without regard to the time stamp value). This bit defaults to "0". In default (reset) mode, the packet will be output with respect to the time stamp value, even if there is a CRC error. CAUTION: If there is an error in the time stamp, the packet may be held far into the future. This will affect subsequently received packets. Bit 7: R/W DIS_TSC: Disable Time Stamp Checking. Defaults to "0", time stamp checking is enabled. When time stamp checking is disabled, the time stamp accompanying a packet is output before the packet to the application for use by the application. This adds an extra quadlet of data to the received data stream; the application must be capable of handling this extra 4 bytes. Bit 6: R/W RMVUAP: Remove unreliable packets from memory, do not attempt delivery Bit 5: R SPAV: Source packet available for delivery in buffer memory. Bit 4: R/W EN_IRX: Enable receiver operation. Value is only checked whenever a new bus packet arrives, so enable/disable while running is `graceful', meaning any transfers in process will be completed before this bit is asserted. Bit 2..3: R/W BPAD: Value indicating the amount of byte padding to be removed from the last data quadlet of each source packet, from 0 to 3 bytes. This is in addition to quadlet padding as defined in IEC 61883 International Standard. Bit 1: Bit 0: R/W R/W EN_FS: Enable processing of SYT stamps. RST_IRX: causes the receiver to be reset when `1'. In order for synchronous reset of IRX to work properly, the application must supply an AVCLK and ensure that the reset bit is kept (programmed) HIGH for at least the duration of one AVCLK period. Failure to do so may cause the application interface of this module to be improperly reset (or not reset at all).
2000 Dec 01
57
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.2.9 Common Isochronous Receiver Packet Header Quadlet 1 (IRXHQ1) - Base Address: 0x044 This quadlet represents the last received header value when AV receiver is operating.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SID E0 F0
DBS
FN
QPC SPH
SV00286
Reset Value 0x00000000 Bit 31..30: R Bit 29..24 R Bit 23.16: R Bit 15..14: R Bit 13..11: Bit 10: R R
E0: End of Header, F0: Format: Always set to 00 for first AV header quadlet. SID: Source ID, contains the node address of the sender of the isochronous data. DBS: Size of the data blocks from which AV payload is constructed. The value 0 represents a length of 256 quadlets. FN (Fraction Number): The encoding for the number of data blocks into which each source packet has been divided (00 = 1, 01 = 2, 10 = 4, 11 = 8) by the transmitter of the packet. QPC: Number of dummy quadlets appended to each source packet before it was divided into data blocks of the specified size. SPH: Indicates that a CYCTM based time stamp is inserted before each application packet (25 bits specified in the IEC 61883 International Standard).
13.2.10 Common Isochronous Receiver Packet Header Quadlet 2 (IRXHQ2) - Base Address: 0x048
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FMT E1 F1
FDF
SYT
SV00287
Reset Value 0x0000FFFF Bit 31..30: R E1: End of Header, F1: Format: Should be set to 10 for second AV header quadlet. Bit 29..24: R FMT: Value inserted in the Format field. Bit 23..0: R FDF/SYT: If ``EN FS" in Register IRXPKCTL (0x040) is set to `1', then lower 16-bits are interpreted as SYT.
2000 Dec 01
58
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.2.11 Isochronous Receiver Interrupt Acknowledge (IRXINTACK) - Base Address: 0x04C
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 IR100LFT IR256LFT IR512LFT IRXFULL IRXEMPTY FSYNC SEQERR CRCERR CIPTAGFLT RCVBP SQOV SYTOVF IRO/E IREMI
SV01025
Reset Value 0x00000000 Bit 14: R/W SYTOVF: SYT FIFO overflow. The isochronous receiver's SYT field FIFO has overflowed and has been automatically reset and cleared. This interrupt alerts the host controller that up to 7 AVFSYNC pulses may be missing due to an SYT field reception error. Bit 13: R/W IRO/E: Odd/even key change. Software should write in the new set of keys to the cipher. Bit 12: R/W IREMI: This bit indicates when there has been a change in the received EMI bit values (bits 2 and 3 of register 0x054). This interrupt, when = 1, indicates that a changed EMI field has been received. Bit 10: R/W IR100LFT: Interrupt when receiver queue reaches 100 quadlets from full. Bit 9: R/W IR256LFT: Interrupt when receiver queue reaches 256 quadlets from full. Bit 8: R/W IR512LFT: Interrupt when receiver queue reaches 512 quadlets from full. This bit is disabled if 0.5K Byte buffer size is set. Bit 7: R/W IRXFULL: Isochronous data memory bank has become full. this is a fatal error, the recommended action is to reset and re-initialize the receiver. Bit 6: R/W IRXEMPTY: Isochronous data memory bank has become empty. Bit 5: R/W FSYNC: Pulse at fsync output. Bit 4: R/W SEQERR: Sequence error of data blocks. Bit 3: R/W CRCERR: CRC error in bus packet. Bit 2: R/W CIPTAGFLT: Faulty CIP header tag (E,F bits). i.e.: The CIP header did not meet the standard and the whole packet is ignored. Bit 1: R/W RCVBP: Bus packet processing complete. Bit 0: R/W SQOV: Status queue overflow. This is a fatal error, the recommended action is to reset and re-initialize the receiver. 13.2.12 Isochronous Receiver Interrupt Enable (IRXINTE) - Base Address: 0x050 Interrupt enable bits for AV Receiver.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ECIPTAGFLT ERCVBP ESQOV EIR100LFT EIR256LFT EIR512LFT EIRXFULL EIRXEMPTY EFSYNC ESEQERR ECRCERR ESYTOVF EIRO/E EIREMI
SV01026
Reset Value 0x00000000 Bit 13..0 are interrupt enable bits for the Isochronous Receiver Interrupt Acknowledge (IRXINTACK).
2000 Dec 01
59
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.2.13 Isochronous Receiver Control Register (IRXCTL) - Base Address: 0x054
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DECPHR_EN ODD/EVEN SY
SPD TAG
CHANNEL
ERR EMI
SV01041
Reset Value 0x00000000 Bit 20: R/W De-cipher Enable: When set the internal M6 cipher will decrypt the application packets with the associated key in the M6 indirect address space for the given EMI value assigned. When the EMI value changes, the cipher will automatically change the key on the next application packet. Changes to the ODD/EVEN bit (bit 1) will automatically swap the odd/even key in the cipher. Note: the maximum average data rate for the M6 cipher is 100 Mbps. Bit 17..16: R SPD: Speed of last received isochronous packet (S100 .. S400). 00 = 100 Mbps 01 = 200 Mbps 10 = 400 Mbps 11 = Reserved Bit 15..14: R/W TAG: Isochronous tag value (must match) for AV format, `01' for IEC 61883 International Standard data. Bit 13..8: R/W CHAN: Channel number to receive isochronous data. Bit 7..4: R ERR: Error code for last received isochronous AV packet. Bit 3..2: R Encryption Mode Indication: This bit pattern specifies the level of copy control information for the data stream. The field only has significance when the internal cipher is enabled (DECPHR_EN = 1). The value of these bits is stored and accompanies the received packet through the IRx FIFO. At a later time, when the first byte of the accompanied packet is presented at the receiving AV port, that EMI value is also presented. Note: The EMI value in this register is indicative only of the EMI value of the packet which is being received from the bus. The EMI value at the AV port may differ due to aging as it progresses through the IRx FIFO. See the "5C Digital Transmission Content Protection Specification, Volume 1" for more details about EMI values. Bit 1: R ODD/EVEN: Used for encryption key (0= even, 1 = odd). When the internal M6 decipher is enabled (DECPHR_EN = 1), changes to this bit field will cause the cipher to swap its odd/even key. An interrupt will be generated, `Odd/even' in the IRXINTACK register to allow firmware to update key sets. See the "5C Digital Transmission Content Protection Specification, Volume 1" for more details about odd/even values. Bit 0: R SY: Sync code to insert in SY field of isochronous bus packet header. This bit reflects the value of the SY bit received from the isochronous header and is synchronized in the receiver FIFO with the data payload that was associated with it. Note: The SY value in this register is indicative only of the EMI packet which is being received from the bus. The SY value at the AV port may differ due to aging as it progresses through the IRx FIFO.
Table 7. Error Codes
Code 0000 0001 0010 through 1100 1101 1110 and 1111 Name reserved complete reserved The node could not accept the block packet because the data field failed the CRC check, or because the length of the data block payload did not match the length contained in the dataLength field. this code shall not be returned for any packet that does not have a data block payload. The node has successfully accepted the packet. If the packet was a request subaction, the destination node has successfully completed the transaction and no response subaction shall follow. Meaning
data_error
reserved
2000 Dec 01
60
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.2.14 Isochronous Receiver Memory Status (IRXMEM) - Base Address: 0x058 The AV Receiver Memory Status register reports on the condition of the internal memory buffer used to store outgoing AV data streams after reception from the 1394 bus. This register is used primarily for diagnostics; several memory flags are also available in the IRXINTACK register.
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 IRXM100LFT IRXM256LFT IRXM512LFT IRXMF IRXMAF IRXM5AV IRXME
SV01057
Reset Value 0x00000003 Bit 6: R Bit 5: R Bit 4: R Bit 3: R Bit 2: R Bit 1: R Bit 0: R
IRXM100LFT: FIFO is 100 quadlets from full. IRXM256LFT: FIFO is 256 quadlets from full. IRXM512LFT: FIFO is 512 quadlets from full. IRXMF: Full: no space available. IRXMAF: Almost full: exactly one quadlet of storage available. IRXM5AV: At least 5 more quadlets of storage available. RXME: Memory bank is empty (no data committed).
2000 Dec 01
61
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.3 Asynchronous Control and Status Interface
13.3.1 Asynchronous RX/TX Control (ASYCTL) - Base Address: 0x080
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DIS_BCAST ARXRST ATXRST ARXALL
MAXRC
TOS
TOF
SV00889
Reset Value 0x00300320 Bit 23: R/W DIS_BCAST: Disable the reception of broadcast packets (async packets address to 0x3F). Bit 22: R/W ARXRST: Asynchronous receiver reset. This bit will auto clear when the link layer state machine is idle. Bit 21: R/W ATXRST: Asynchronous transmitter reset. the power-up reset value of this bit is "0", however, after every bus reset this bit is set (1). this effectively disables the asynchronous transmitter; re-enable the async transmitter by clearing this bit after each bus reset, especially if asynchronous transmission is to be used. Bit 20: R/W ARXALL: Receive and filter only RESPONSE packets. When set (1), all responses are stored. When clear (0), only solicited responses are stored. Bit 19..16: R/W MAXRC: Maximum number of asynchronous transmitter single phase retries Bit 15..13: R/W TOS: Time out seconds, integer of 1 second Bit 12..0: R/W TOF: Time out fractions, integer of 1/8000 second. Resets to 0320h, which is 100 milliseconds. 13.3.2 Asynchronous RX/TX Memory Status (ASYMEM) - Base Address: 0x084
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 TRSPQIDLE TREQQIDLE RRSPQF RRSPQAF RRSPQ5AV RRSPQE RREQQF RREQQAF RREQQ5AV RREQQE TRSPQF TRSPQAF TRSPQ5AV TRSPQE TREQQF TREQQAF TREQQ5AV TREQQE
SV00918
Reset Value 0x00033333 Bit 17: Bit 16: Bit 15: Bit 14: Bit 13: Bit 12: Bit 11: Bit 10: Bit 9: Bit 8: Bit 7: Bit 6: Bit 5: Bit 4: Bit 3: Bit 2: Bit 1: Bit 0: R R R R R R R R R R R R R R R R R R Unused bits read `0'. The information in this register is primarily used for diagnostics. TRSPQIDLE: Transmitter response queue is idle. Indicates that the transfer register for this queue is empty. TREQQIDLE: Transmitter request queue is idle. Indicates that the transfer register for this queue is empty. RRSPQF: Receiver response queue full. RRSPQAF: Receiver response queue almost full (precisely 1 more quadlet available). RRSPQ5AV: Receiver response queue at least 5 quadlets available. RRSPQE: Receiver response queue empty. RREQQF: Receiver request queue full. RREQQAF: Receiver request queue almost full (precisely 1 more quadlet available). RREQQ5AV: Receiver request queue at least 5 quadlets available. RREQQE: Receiver request queue empty. TRSPQF: Transmitter response queue full. TRSPQAF: Transmitter response queue almost full (precisely 1 more quadlet available). TRSPQ5AV: Transmitter response queue at least 5 quadlets available. TRSPQE: Transmitter response queue empty. TREQQF: Transmitter request queue full. TREQQAF: Transmitter request queue almost full (precisely 1 more quadlet available). TREQQ5AV: Transmitter request queue at least 5 quadlets available. TREQQE: Transmitter request queue empty.
2000 Dec 01
62
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.3.3 Asynchronous Transmit Request Next (TX_RQ_NEXT) - Base Address: 0x088
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TX_RQ_NEXT
SV00293
Bit 31..0:
W TX_RQ_NEXT: First/middle quadlet of packet for transmitter request queue (write only). Writing this register will clear the TREQQWR flag until the quadlet has been written to its queue.
13.3.4 Asynchronous Transmit Request Last (TX_RQ_LAST) - Base Address: 0x08C
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TX_RQ_LAST
SV00294
Bit 31..0:
W TX_RQ_LAST: Last quadlet of packet for transmitter request queue (write only). Writing this register will clear the TREQQWR flag until the quadlet has been written to its queue.
13.3.5 Asynchronous Transmit Response Next (TX_RP_NEXT) - Base Address: 0x090
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TX_RP_NEXT
SV00295
Bit 31..0:
W TX_RP_NEXT: First/middle quadlet of packet for transmitter response queue (write only). Writing this register will clear the TRSPQWR flag until the quadlet has been written to its queue.
13.3.6 Asynchronous Transmit Response Last (TX_RP_LAST) - Base Address: 0x094
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TX_RP_LAST
SV00296
Bit 31..0:
W TX_RP_LAST: Last quadlet of packet for transmitter response queue (write only). Writing this register will clear the TRSPQWR flag until the quadlet has been written to its queue.
2000 Dec 01
63
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.3.7 Asynchronous Receive Request (RREQ) - Base Address: 0x098
3130 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RREQ
SV00297
Reset Value 0x00000000 Bit 31..0: R RREQ:Quadlet of packet from receiver request queue (transfer register). Reading this register will clear the RREQQQAV flag until the next received quadlet is available for reading. 13.3.8 Asynchronous Receive Response (RRSP) - Base Address: 0x09C
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RRSP
SV00298
Reset Value 0x00000000 Bit 31..0: R RRSP:Quadlet of packet from receiver response queue (transfer register). Reading this register will clear the RRSPQQAV flag until the next received quadlet is available for reading. 13.3.9 Asynchronous RX/TX Interrupt Acknowledge (ASYINTACK) - Base Address: 0x0A0
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 RREQQRDERR RRSPQRDERR RREQQLASTQ RRSPQLASTQ RREQQFULL RRSPQFULL 9 8 7 6 5 4 TREQQFULL 3 TRSPQWRERR 2 TREQQWRERR 1 0
TRSPQFULL
RREQQQAV
RRSPQQAV
SV00796
Reset Value 0x00000C00 Bit 31..17: R/W Bit 16: R/W Bit 15: R/W Bit 14: R/W Bit 13: Bit 12: Bit 11: Bit 10: Bit 9: Bit 8: Bit 7: Bit 6: Bit 5: Bit 4: Bit 3: Bit 2: Bit 1: Bit 0: R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Unused bits read `0' RRSPQFULL: Receiver response queue did become full. Write a "1" to this bit to reset the interrupt. RREQQFULL: Receiver request queue did become full. Write a "1" to this bit to reset the interrupt. SIDQAV: Current quadlet in RREQ is selfID data. This bit is set only after a bus reset, not after reception of PHY packets other than self IDs. This interrupt automatically resets when the quadlet is read. RRSPQLASTQ: Current quadlet in RRSP is last quadlet of packet. This interrupt automatically resets when the quadlet is read. RREQQLASTQ: Current quadlet in RREQ is last quadlet of packet. This interrupt automatically resets when the quadlet is read. RRSPQRDERR: Receiver response queue read error (transfer error) or bus reset occurred. When set (1), this queue is blocked for read access. Write a "1" to this bit to reset the interrupt. RREQQRDERR: Receiver request queue read error (transfer error) or bus reset occurred. When set (1), this queue is blocked for read access. Write a "1" to this bit to reset the interrupt. RRSPQQAV: Receiver response queue quadlet available (in RRSP). This interrupt automatically resets when the quadlet is read. RREQQQAV: Receiver request queue quadlet available (in RREQ). This interrupt automatically resets when the quadlet is read. TIMEOUT: Split transaction response timeout. Write a "1" to this bit to reset the interrupt. RCVDRSP: Solicited response received (within timeout interval). Write a "1" to this bit to reset the interrupt. TRSPQFULL: Transmitter response queue did become full. Write a "1" to this bit to reset the interrupt. TREQQFULL: Transmitter request queue did become full. Write a "1" to this bit to reset the interrupt. TRSPQWRERR: Transmitter response queue write error (transfer error). Write a "1" to this bit to reset the interrupt. TREQQWRERR: Transmitter request queue write error (transfer error). Write a "1" to this bit to reset the interrupt. TRSPQWR: Transmitter response queue written (transfer register emptied). Write a "1" to this bit to reset the interrupt. TREQQWR: Transmitter request queue written (transfer register emptied). Write a "1" to this bit to reset the interrupt.
2000 Dec 01
64
TREQQWR
TIMEOUT
TRSPQWR
RCVDRSP
SIDQAV
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.3.10 Asynchronous RX/TX Interrupt Enable (ASYINTE) - Base Address: 0x0A4
31 30 29 28 27 26 25 24 23
22 21 20 19 18 17 16 15 14 13 12 11 10 ERREQQRDERR ERRSPQRDERR ERREQQLASTQ ERRSPQLASTQ ERREQQFULL ERRSPQFULL
9 ERRSPQQAV
8 ERREQQQAV
7
6
5 ETRSPQFULL
4 ETREQQFULL
3 ETRSPQWRERR
2 ETREQQWRERR
1
0
SV00797
Reset Value 0x00000000 Bits16..0 are interrupt enable bits for the Asynchronous RX/TX Interrupt Acknowledge (ASYINTACK). 13.3.11 RDI Register - Base Address: 0x0B0
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 LPSTAT 9 8 7 6 5 4 3 2 1 0
SWPD
ESCA
ELOA
ESCI
EPLI
SCA
LOA
ETRSPQWR
SV01863
NOTE: 1. Also refer to Section 12.5.3 for functional descriptions. Reset Value 0x00000000 Note: Before asserting the RPL bit, SWPD or setting the PD pin high, the user should assure that the link chip is in the following state of operation: 1) The isochronous transmit FIFO is not receiving data for transmission 2) The isochronous transmitter is disabled 3) No asynchronous packets are being generated for transmission 4) Both the ASYNC request and response queues are empty SWPD: Software power-down. Writing a 1 to this register bit will cause the link to de-activate its LPS pin causing the PHY to turn off the SCLK to the link. This, in turn, causes the link chip to go into a low power mode in which only the RDI register is accessible. The function of this bit is identical to that of the hardware pin "PD". When PD is set (1), SWPD will be set automatically by the pin state and will cause entry into the power down mode as stated above. DO NOT USE BOTH (HARDWARE AND SOFTWARE) MODES OF OPERATION TO CAUSE THE POWER DOWN FUNCTION. Use either hardware mode (the PD pin) OR the software method (setting / resetting the SWPD bit), not both. The PD pin will take precedence over the software method... the link will not come out of PD mode unless the PD pin is deasserted (0). An unused PD pin should be connected to the link chip ground. The SWPD does not indicate the status of the PD pin. See Section 12.5.3 for more information. LPSTAT: Link - PHY interface status. This bit reflects the status of the LPS signal. When the LPS signal is active (pulsing) the PHY interprets it as indicating that the link power is on and the link is requesting to be activated. The PHY, in turn, supplies the SCLK to the link, thus giving it the means to become active. The SCLK is used by the link to operate most of its internal circuitry. If LPS was active and then de-activated, it is a signal to the PHY chip that the link desires entry into the power down mode. The LPSTAT bit continually indicates the status of the LPS pin and thus the overall status of the link - PHY interface. It should also be noted here that a momentary de-activation of the LPS signal by the setting of the RPL bit (bit 18 of register 0x004, LNKCTL) to cause a link - PHY interface reset will also be indicated by the LPSTAT bit. It is suggested that this momentary status change be ignored when the host controller causes a link - PHY reset through the use of the RPL bit. EPLI: Enable the PHY - link initialized interrupt. Leaving this bit in the reset (0) state allows the PLI bit to be read as a status bit. ELOA: Enable link-on active interrupt. Leaving this bit in the reset (0) state allows the LOA bit to be read as a status bit. ESCA: Enable SCLK active interrupt. Leaving this bit in the reset (0) state allows the SCA bit to be read as a status bit. ESCI: Enable SCLK inactive interrupt. Leaving this bit in the reset (0) state allows the SCI bit to be read as a status bit.
Bit 31:
R/W
Bit 30:
R
Bit 19: Bit 18: Bit 17: Bit 16:
R/W R/W R/W R/W
2000 Dec 01
65
SCI
PLI
ETREQQWR
ERCVDRSP
ETIMEOUT
ESIDQAV
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
Bit 3:
R/W
Bit 2:
R/W
Bit 1:
R/W
Bit 0:
R/W
PLI: PHY - link interface initialized interrupt. This interrupt indicates when the PHY - link initialization routine has been accomplished. This bit will be set upon completion of the initialization; if enabled, it will cause a host interface interrupt in order to inform the host controller of the completed action. Reset of this interrupt requires the writing of a (1) to this bit position. When used as a status bit it will be necessary to first write a "1" to this bit position before reading the status of this bit. . . see Section 12.5.3 for a full explanation. LOA: Link-on active interrupt. This interrupt will become active when a link-on signal is received by the link from the PHY. This bit will remain active as long as the link-on signal is active. When enabled, this bit will set and cause a host interface interrupt when the link detects the presence of a link-on signal from the PHY. In practice, the link will be in the power down state when this interrupt occurs (a link-on packet was sent by another node on the bus which desires to communicate with this powered down node). Proper servicing of this interrupt will contain a scenario similar to: this node is in power down mode and the host controller has set the ELOA bit to enable the interrupt and the PHY of this node received a link-on packet from another node requesting this node to power up; (1) the host controller gets the interrupt and makes a decision to power up, (2) the host de-asserts SWPD (by hardware or software means... see SWPD above), (3) the host monitors SCA for a "1" state, (4) when SCA is true, the host writes a 0 to the ELOA bit and then writes a 1 to the LOA interrupt bit to cancel the interrupt. The link is now powered up. When used as a status bit it will be necessary to first write a "1" to this bit position before reading the status of this bit. . . see Section 12.5.3 for a full explanation. SCA: SCLK active interrupt. When the SCLK signal from the PHY to the link is present, this bit is set. If this interrupt has been enabled, the host will receive an interrupt when the SCLK becomes active (an example of such use might be during the recovery from a link power down situation). When used as a status bit it will be necessary to first write a "1" to this bit position before reading the status of this bit. . . see Section 12.5.3 for a full explanation. SCI: SCLK inactive interrupt. When the SCLK signal is NOT active, this bit sets. If this interrupt is enabled, when the SCLK ceases to be active, the interrupt will occur. SCLK could become inactive due to the PHY connected to this link going into power down mode. SCI operates as a true status bit. See Section 12.5.3.
13.3.12 Shadow Register (SHADOW_REG) - Base Address: 0x0F4
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
BYTE 0
BYTE 1
BYTE 2
BYTE 3
SV01817
Reset Value 0x0F0A0500 Bit 31..0: R/W The shadow register is a mechanism that allows a byte (8-bit) or word (16-bit) host interface write quadlets (32-bit) into the AV Link. Bytes or words can be written into the shadow register in any order and then written to the AV Link by asserting address line A8 with the desired address. For example, if you want to write to Transmit Request Next register (TX_RQ_NEXT), and you were using an 8-bit host, then you would write the first three bytes to the shadow register and the fourth byte to the address 0x188 (or 0x189, or 0x18A, or 0x18B). In practice, any write or read with address line A8 not asserted will be directed to the shadow register. To verify the settings of LTLEND and DATAINV, this register is initialized to 0x0F0A0500 on power up. Note, unlike the other registers in this device, access to this register should not be addressed with address line A8 = 1.
2000 Dec 01
66
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.4 Indirect Address Registers
13.4.1 The host interface register set has been extended to provide additional control and data registers for FIFO size control and copy protection control registers. These extensions have been implemented via an indirect addressing mechanism. This mechanism allows software written for previous versions of the AV Link (PDI1394L21 and PDI1394L11) to operate on the PDI1394L41 with minimal changes. To read or write from the indirect memory, you first write the appropriate address into the indirect address register (A8 = 1), then read or write from (or to) the indirect data increment the indirect address by one quadlet. Therefore, if you are writing several quadlets to continuous addresses, you will not need to increment the indirect address register. 13.4.2 Indirect Address Register (INDADDR) - Base Address: 0x0F8
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
RESERVED
INDADDR
SV01027
Bit 15..0:
R/W
Indirect Address: To read or write from the indirect memory, you first write the appropriate address into the indirect address register (A8 = 1), then read or write from (or to) the indirect data register (INDDATA, 0x0FC). Each write or read (A8 = 1) to the indirect data register (INDDATA) will automatically increment the indirect address by one quadlet. The following addresses are defined in the indirect address space:
Table 8. INDADDR address and function
INDADDR 0-0x0FC 0x100-0x1FC 0x200-0x3FC 0x400-0x4FC 0x500-0xFFFF Reserved FIFO Size Registers See datasheet addendum See datasheet addendum Reserved FUNCTION
13.4.3 Indirect Data Register (INDDATA) - Base Address: 0x0FC
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
WINDOW TO THE INDIRECT QUADLET POINTED TO BY INDADDR
SV01764
Bit 31..0:
R/W
Quadlet of data pointed to by the indirect address n the INDADDR register (0x0F8). Note that the Indirect address autoincrements on each read or write of the INDDATA register.
2000 Dec 01
67
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.5 Indirect Address Registers
The following registers are defined in the indirect address space. Access to these registers must be made through the Indirect Address (INDADDR) and Indirect Data (INDDATA) registers. 13.5.1 Registers for FIFO Size Programming Each FIFO can be programmed to a certain size with a granularity of 64 quadlets. The size is determined by the values of the base_fifo and end_fifo fields of the FIFO Size registers. The following formula applies: fifo_size = (end_fifo - base_fifo + 1) x 64 quadlets The FIFO's have been implemented on a single memory. The base_fifo and end_fifo fields are sued to determine the physical start and end address of each FIFO inside the memory. The start address of a FIFO is {fifo_addr[11:6] = base_fifo, fifo_addr[5:0] = 000000}. The end address of a FIFO is {fifo_addr[11:6] = end_fifo, fifo_addr[5:0] = 111111}. Note: The end_fifo must be larger than base_fifo and the hardware does not check for invalid values.
RRSPSIZE: base_fifo RRSPSIZE: end_fifo RREQSIZE: base_fifo RREQSIZE: end_fifo TRSPSIZE: base_fifo TRSPSIZE: end_fifo TREQSIZE: base_fifo TREQSIZE: end_fifo IRXSIZE: base_fifo IRXSIZE: end_fifo ITXSIZE: base_fifo ITXSIZE: end_fifo
000000 RRSP 000011 000100 RREQ 000111 001000 TRSP 001011 001100 TRSP 001111 & 111111 010000 IRX 011111 100000 & 000000 ITX 101111
Fields in FIFO Size registers
fifo_bank
SV01765
Figure 34. Reset situation of size programmable FIFOs 13.5.1.1 Asynchronous Receive Response FIFO Size (RRSPSIZE) - Indirect Address: 0x100
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
base_fifo 0 0 0 0 0 0 0 0
end_fifo 0 0 1 1
SV01766
Reset Value 0x00000003 Bit 31..14 R/W Bit 13..8 R/W Bit 7, 6 R/W Bit 5..0 R/W
Unused bits read `0' base_fifo: Base address of the FIFO Unused bits read `0' end_fifo: End address of the FIFO
2000 Dec 01
68
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.5.1.2 Asynchronous Receive Request FIFO Size (RREQSIZE) - Indirect Address: 0x104
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
base_fifo 0 0 0 1 0 0 0 0
end_fifo 0 1 1 1
SV01767
Reset Value 0x00000407 Bit 31..14 R/W Bit 13..8 R/W Bit 7, 6 R/W Bit 5..0 R/W
Unused bits read `0' base_fifo: Base address of the FIFO Unused bits read `0' end_fifo: End address of the FIFO
13.5.1.3 Asynchronous Transmit Response FIFO Size (TRSPSIZE) - Indirect Address: 0x110
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
base_fifo 0 0 1 0 0 0 0 0
end_fifo 1 0 1 1
SV01768
Reset Value 0x0000080B Bit 31..14 R/W Bit 13..8 R/W Bit 7, 6 R/W Bit 5..0 R/W
Unused bits read `0' base_fifo: Base address of the FIFO Unused bits read `0' end_fifo: End address of the FIFO
13.5.1.4 Asynchronous Transmit Request FIFO Size (TREQSIZE) - Indirect Address: 0x114
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
base_fifo 0 0 1 1 0 0 0 0
end_fifo 1 1 1 1
SV01769
Reset Value 0x00000C0F Bit 31..14 R/W Bit 13..8 R/W Bit 7, 6 R/W Bit 5..0 R/W
Unused bits read `0' base_fifo: Base address of the FIFO Unused bits read `0' end_fifo: End address of the FIFO
2000 Dec 01
69
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
13.5.1.5 Isochronous Receiver FIFO Size (IRXSIZE) - Indirect Address: 0x120
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
base_fifo 0 1 0 0 0 0 0 1
end_fifo 1 1 1 1
SV01770
Reset Value 0x0000101F Bit 31..14 R/W Bit 13..8 R/W Bit 7, 6 R/W Bit 5..0 R/W
Unused bits read `0' base_fifo: Base address of the FIFO Unused bits read `0' end_fifo: End address of the FIFO
13.5.1.6 Isochronous Transmitter FIFO Size (ITXSIZE) - Indirect Address: 0x130
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
base_fifo 1 0 0 0 0 0 1 0
end_fifo 1 1 1 1
SV01771
Reset Value 0x0000202F Bit 31..14 R/W Bit 13..8 R/W Bit 7, 6 R/W Bit 5..0 R/W
Unused bits read `0' base_fifo: Base address of the FIFO Unused bits read `0' end_fifo: End address of the FIFO
2000 Dec 01
70
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
14.0 DC ELECTRICAL CHARACTERISTICS Table 9. DC Electrical Characteristics
SYMBOL VIL VIH VIT1+ VIT1- VIT2+ VIT2- VOH1 PARAMETER LOW input voltage HIGH input voltage Input threshold, rising edge Input threshold, falling edge Input threshold, rising edge Input threshold, falling edge HIGH output voltage .42 VDD + 0.2 2.4 MIN 2.0 VDD/2 + 0.3 VDD/2 - 0.9 VDD/2 + 0.9 VDD/2 - 0.3 .42 VDD + 1.0 MAX 0.8 UNIT V V V V V V V NOTE Pin categories 1, 2, 3 Pin categories 1, 2, 3 Pin categories 6, 8 LOW to HIGH transition Pin categories 6, 8 HIGH to LOW transition Pin category 9 LOW to HIGH transition Pin category 9 HIGH to LOW transition Pin category 1 IOH = 4mA IOL = 4mA Pin category 1 IOH = 4mA IOL = 4mA Pin categories 4, 6, 7 IOH = 4mA Pin categories 4, 5, 6, 7 IOL = 4mA Pin categories 2, 3, 9 VI = 5.5 V or 0 V Pin categories 6, 8 VDD = 3.6 V, VIN = VDD/2 Pin categories 6, 8 VDD = 3.6 V, VIN = 0 V, 3.6 V Pin categories 6, 8 VDD = 3.0 V, VIN = 5.5 V Pin categories 6, 8 VDD = 0 V, VIN = 5.5 V Pin categories 1, 7 VI = 5.5 V or 0 V VDD = 3.6 V VDD = 3.6 V
VOL1 VOH2 VOL2 IL
LOW output voltage HIGH output voltage LOW output voltage Input leakage current Vdd = 3.6 V ISON = high 2.4
0.4
V V
0.4 1 1000 5 500 750 5 200 10
V mA mA mA mA mA mA mA mA
IL
In ut Input leakage current ISON = low ISON = high
IL
In ut Input leakage current ISON = low
IOZ IDD
3-State output current Su ly Supply current
VDD = 3.6 V Operating Powered-down
14.1 Pin Categories Table 10. Pin Categories
Category 1: Input/Output HIF AD[7:0] AVxSYNC AV2ERR0 AV2ERR1 AVxVALID AV xD[7:0] AVxCLK AVxFSYNC HIF D[15:8] HIF A[7:0] AVxSYSYNC AVxSY AVxREADY AVxENDPCK HIF ALE HIF RDN Category 2: Input HIF A[8] HIF CSN HIF WRN Category 3: Input RESETN CYCLEIN ISON HIF MUX HIF16BIT 1394MODE AVxEMI AV1ERR0 AV1ERR1 Category 4: Output CYCLEOUT CLK50 HIF WAIT Category 5: Output HIF INTN Category 6: Input/Output PHY D[0:7] PHY CTL[0:1] Category 7: Output LREQ LPS Category 8: Input SCLK Category 9: Input LNKON
2000 Dec 01
71
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
15.0 AC CHARACTERISTICS
GND = 0 V, CL = 50 pF LIMITS SYMBOL PARAMETER TEST CONDITIONS WAVEFORMS Tamb = 0 C to +70 C MIN tPERIOD (parallel mode) tSU tIH tOD tWHIGH tWLOW tPWFS tSUP tHP tSCLKPER tDP tAS tAH tCL tCH tRP tACC tDH tDS tDZ tWRP tWAIT tWWAIT tCWH tCWL tCP tCD tRESET tPWALE tALES tALEH fLPS dcLPS AV clock period AV clock setup time AV clock input hold time AV clock output delay time AV clock pulse width HIGH AV clock pulse width LOW AVxFSYNC pulse width HIGH PHY-link setup time PHY-link hold time SCLK period PHY-link output delay Host address setup time Host address hold time Host chip select pulse width LOW Host chip select pulse width HIGH Host read pulse width Host access time Host data hold time Host data setup time Host data bus release (Hi-Z) Host write pulse width WAIT output delay WAIT pulse width CYCLEIN HIGH pulse width CYCLEIN LOW pulse width CYCLEIN cycle period CYCLEOUT cycle delay RESET_N pulse width LOW ALE pulse width ALE setup time ALE hold time LPS signal frequency LPS signal duty cycle Note: CL = 20 pF Figure 36 Figure 36 Figure 36 Figure 36 Figure 36 Figure 36 Figure 37 Figure 38 Figure 38 Figure 38 Figure 39 Figure 40 Figure 40 Figure 40 Figure 40 Figure 40 Figure 40 Figure 40 Figure 40 Figure 40 Figure 40 Figure 40 Figure 40 Figure 41 Figure 41 Figure 41 Figure 42 Figure 43 Figures 8, 9, 10, 11 Figures 8, 9, 10, 11 Figures 8, 9, 10, 11 - - 10 20 3 2 1.0 23 2.75 28 62 200 200 125 20 115 12 2 0 15 41.67 4 3 3 10 10 200 6.0 0 20.343 2.0 0 2 115 42 115 115 20.345 20.347 10.0 300 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns s ns s ns ns ns MHz % 24 TYP MAX ns ns ns ns UNIT
2000 Dec 01
72
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
16.0 TIMING DIAGRAMS 16.1 AV Interface Operation
AVCLK
AV D[7:0]
MESSAGE
INVALID DATA
MESSAGE
INVALID DATA
MESSAGE
AVSYNC
AVVALID
AVERR[0]
ASSERTED IN THE EVENT OF A BUS PACKET CRC ERROR
AVERR[1]
ASSERTED IN THE EVENT OF A DATA BLOCK SEQUENCE ERROR
SV00240
Figure 35. AV Parallel Interface Operation Diagram
16.2 AV Interface Critical Timings
AVCLK tWHIGH tWLOW tPERIOD
AV D [7:0], AVVALID, AVSYNC, AVENDPCK SY, READY
VALID tSU tIH
AV D [7:0], AVERR[1:0], AVSYNC, AVVALID
Figure 36. AV Interface Timing Diagram
AVxFSYNC tPWFS
NOTE: 1. Timing shown is for AVxFSYNC used as an output only. When AVxFSYNC is used as an input, only the rising edge of the signal is considered as long as the input pulse width exceeds 40 nS. Figure 37. AVxFSYNC Timing Diagram
2000 Dec 01
EEE EEE
tOD
EEE EEE
VALID
SV01864
SV00890
73
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
16.3 PHY-Link Interface Critical Timings
tSCLKPER SCLK tSUP 50% tHP 50% 50%
PHY D[0:7], PHY CTL[0:1]
50%
SV00919
Figure 38. PHY D[0:7], PHY CTL[0:1] Input Setup and Hold Timing Waveforms
SCLK
50% tDP
PHY D[0:7], PHY CTL[0:1], LREQ
50%
SV00694
Figure 39. PHY D[0:7], PHY CTL[0:1], and LREQ Output-Delay Timing Waveforms
2000 Dec 01
74
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
16.4 Host Interface Critical Timings
READ
tAS HIF A[7:0] VALID tCL HIF CS_N tRP HIF RD_N tCH tAS tAH tAH
HIF D[7:0] tAS
A8
tWAIT WAIT
WRITE
tWRP HIF WR_N
HIF D[7:0] tDS
A8
WAIT tWAIT
NOTE: 1. Wait line asserts only during Read and Write cycles in which A8 is asserted. Figure 40. Host Interface Timing Waveforms
2000 Dec 01
EEEEEEEEE EEEEEEEEE EEEEEEEEE
tACC tPWWAIT VALID
VALID tDZ
tDH
SV01869
75
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
16.5 CYCLEIN/CYCLEOUT Timings
CYCLEIN 50% tCWH 50% tCWL 50%
tCP
SV00696
Figure 41. CYCLEIN Waveform
SCLK
50%
50%
CYCLEIN tCD CYCLEOUT 50% tCD 50%
SV00697
Figure 42. CYCLEOUT Waveforms
16.6 RESET Timings
RESET_N
50% tRESET
50%
SV00698
Figure 43. RESET_N Waveform
2000 Dec 01
76
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
LQFP144: plastic low profile quad flat package; 144 leads; body 20 x 20 x 1.4 mm
SOT486-1
2000 Dec 01
77
Philips Semiconductors
Preliminary specification
1394 content protection AV link layer controller
PDI1394L41
Data sheet status
Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.
Production
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Disclaimers
Life support -- These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 (c) Copyright Philips Electronics North America Corporation 2001 All rights reserved. Printed in U.S.A. Date of release: 01-01 Document order number: 9397 750 07931
Philips Semiconductors
2000 Dec 01 78
FOR UNRESTRICTED DISTRIBUTION ERRATA FOR THE PHILIPS PDI1394L41 1394 CONTENT PROTECTION AV LINK LAYER CONTROLLER (This errata list refers only to version 0202 of the L41 chip... package date codes after date code 0030 and the L41 Data Sheet dated 2000 December 01)
Chip Errata:
E-1. AV1READY pin initialization state (after hardware reset of the chip)
Description of expected operation: This pin should be in the output state with a LOW applied immediately after power on reset and after any subsequent hardware reset. Description of observed behavior: The AV1READY pin is in an undefined output state (with level being HIGH or LOW) after power-up and after subsequent hardware resets of the L41. Solution or work around: The host controller software power-up routine should be modified to place the pin state in the proper condition (as it will be used later) immediately after power-up and after any subsequent hardware reset. The proper state of the pin can be set by means of the GLOBCSR register (0x018), by placing the proper states on bits 16 and 17, DIRAV1 and ENOUTAV1. E-2. Register 0x008, LNKPHYINTACK, bit 11 is set at all times.
Description of expected operation: This bit position is not used and therefore should indicate a "0" or reset condition at all times. Description of observed behavior: This bit always indicates a "1" state. Solution or work around: Ignore the state of this bit in this register. The reset state of this register is "00000800" instead of the data sheet indicated "00000000". The state of this bit will be changed to "0" in subsequent versions of this part. E-3 RDI register bits do not function properly when the L41 part is used with PDI1394P11A PHY
Description of expected operation: When the L41 is placed in power-down mode (either by setting the SWPD bit in the RDI register or placing the PD pin in the HIGH state), the L41 stops producing the LPS signal and the PHY interprets this lack of LPS signal as the impetus to remove the SYSCLK (system clock) from the link - PHY interface. This action causes the L41 to enter power-down mode and should place the SCA bit LOW, the PLI bit LOW, and the SCI bit HIGH. Description of observed behavior: The SCA, PLI and SCI bits of the RDI register do not reset / set when SWPD or the PD pin is asserted. This is due to the fact that the SYSCLK output of the P11A PHY remains HIGH when the clock is stopped. The SCA and PLI bits will erroneously read as if the L41 is powered up, they will both remain HIGH. The SCI bit, which is normally set (1) when the L41 is powered-down, will remain reset (0) in this case. Reading the status of these bits in the RDI register will give a false indication that the L41 is operating when it is not. Solution or work around: A hardware work-around for this problem exists. It consists of adding a pull down resistor to set a low dc bias level on the SCLK input of the L41 so as to make the pin go to the LOW state when the clock is not present. The value of the resistor is R= 3.3 KOhms; a 1/10th watt type is sufficient.
Philips Semiconductors
Errata To the PDI1394L41 1394 AV Link Layer Controller (Data Sheet dated: 2000 December 01). December 01, 2000 - Page 79
E-4
When the L41 is used with IEEE 1394-1995 compatible PHYs, RDI register bit "PLI" does not function.
Description of expected operation: When the L41 is placed in power-down mode (either by setting the SWPD bit in the RDI register or placing the PD pin in the HIGH state), the L41 stops producing the LPS signal and the PHY interprets this lack of LPS signal as a request to remove the SYSCLK (system clock) from the link - PHY interface. This action causes the L41 to enter power-down mode and should place the SCA bit LOW, the PLI bit LOW, and the SCI bit HIGH. Description of observed behavior: The PLI bit (bit 3) always indicates a set (1) condition regardless of whether the L41 is powered up or powered down. This is normal bit PLI operation when the L41 is used with a NON 1394A type of PHY. Solution or work around: Non-1394A PHYs do not initialize the link-PHY interface... this is normal functioning. When the L41 is operated with its 1394 MODE pin held high (as is the case when operating with a 1394-1995 PHY) the PLI bit in the RDI register will always be seen as set (1). In order to determine the status of operation of the L41, the SCA and SCI bits may be used (SCI bit recommended) to determine the power status of the link chip. The PLI bit should be ignored by the node operating software when the L41 is operated with a NON-1394A PHY with the L41 1394 MODE pin at 3.3v (high). E-5 E-6 See the Restricted Errata document for this errata... it deals with a DTCP regulated aspect of the L41. See the Restricted Errata document for this errata... it deals with a DTCP regulated aspect of the L41.
Philips Semiconductors
Errata To the PDI1394L41 1394 AV Link Layer Controller (Data Sheet dated: 2000 December 01). December 01, 2000 - Page 80


▲Up To Search▲   

 
Price & Availability of PDI1394L41

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X