 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 0.5 CMOS, Dual 2:1 MUX/SPDT Audio Switch ADG884 FEATURES 1.8 V to 5.5 V operation Ultralow on resistance 0.34 typ 0.38 max at 5 V supply Excellent audio performance, ultralow distortion 0.1 typ 0.15 max RON flatness High current carrying capability 400 mA continuous 600 mA peak current at 5 V supply Rail-to-rail switching operation Typical power consumption (<0.1 W) FUNCTIONAL BLOCK DIAGRAM ADG884 S1A D1 S1B IN1 IN2 S2A D2 S2B 05028-001 SWITCHES SHOWN FOR A LOGIC 1 INPUT Figure 1. APPLICATIONS Cellular phones PDAs MP3 players Power routing Battery-powered systems PCMCIA cards Modems Audio and video signal routing Communications systems GENERAL DESCRIPTION The ADG884 is a low voltage CMOS device containing two independently selectable single-pole, double-throw (SPDT) switches. This device offers ultralow on resistance of less than 0.4 over the full temperature range, making the part an ideal solution for applications that require minimal distortion through the switch. The ADG884 also has the capability of carrying large amounts of current, typically 600 mA at 5 V operation. The ADG884 is available in a 10 bump, 2.0 mm x 1.50 mm WLCSP package, a 10-lead LFCSP package, and a 10-lead MSOP package. These tiny packages make the ADG884 the ideal solution for space-constrained applications. When on, each switch conducts equally well in both directions and has an input signal range that extends to the supplies. The ADG884 exhibits break-before-make switching action. PRODUCT HIGHLIGHTS 1. 2. 3. 4. 5. Single 1.8 V to 5.5 V operation. High current handling capability (400 mA continuous current at 3.3 V). 1.8 V logic-compatible. Low THD + N (0.01% typ). Tiny 2 mm x 1.5 mm WLCSP package, 3 mm x 3 mm 10-lead LFCSP package, and 10-lead MSOP package. Table 1. ADG884 Truth Table Logic (IN1/IN2) 0 1 Switch 1A/2A Off On Switch 1B/2B On Off Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c) 2005 Analog Devices, Inc. All rights reserved. ADG884 TABLE OF CONTENTS Specifications..................................................................................... 3 Absolute Maximum Ratings............................................................ 6 ESD Caution.................................................................................. 6 Pin Configurations and Function Descriptions ........................... 7 Typical Performance Characteristics ............................................. 8 Terminology .................................................................................... 11 Test Circuits..................................................................................... 12 Outline Dimensions ....................................................................... 14 Ordering Guide .......................................................................... 15 REVISION HISTORY 6/05--Rev. 0 to Rev. A Updated Outline Dimensions ....................................................... 14 Changes to Ordering Guide .......................................................... 15 10/04--Revision 0: Initial Version Rev. A | Page 2 of 16 ADG884 SPECIFICATIONS VDD = 5 V 10%, GND = 0 V, unless otherwise noted. 1 Table 2. Parameter ANALOG SWITCH Analog Signal Range On Resistance, RON On Resistance Match Between Channels, RON On Resistance Flatness, RFLAT (ON) LEAKAGE CURRENTS Source Off Leakage, IS (OFF) Channel On Leakage, ID, IS (ON) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS 2 tON tOFF Break-Before-Make Time Delay, tBBM Charge Injection Off Isolation Channel-to-Channel Crosstalk 25C -40C to +85C 0 V to VDD 0.28 0.34 0.01 0.035 0.1 0.13 0.2 0.2 2.0 0.8 0.005 0.1 2 42 50 15 20 16 125 -60 -120 -60 Total Harmonic Distortion, THD + N Insertion Loss -3 dB Bandwidth CS (OFF) CD, CS (ON) POWER REQUIREMENTS IDD 0.017 -0.03 18 103 295 0.003 1 1 2 Unit V typ max typ max typ max nA typ nA typ V min V max A typ A max pF typ ns typ ns max ns typ ns max ns typ ns min pC typ dB typ dB typ dB typ % dB typ MHz typ pF typ pF typ A typ A max Test Conditions/Comments 0.38 0.05 0.15 VDD = 4.5 V, VS = 0 V to VDD, IS = 100 mA See Figure 18 VDD = 4.5 V, VS = 2 V, IS = 100 mA VDD = 4.5 V, VS = 0 V to VDD IS = 100 mA VDD = 5.5 V VS = 0.6 V/4.5 V, VD = 4.5 V/0.6 V; see Figure 19 VS = VD = 0.6 V or 4.5 V; see Figure 20 VIN = VINL or VINH 53 21 10 RL = 50 , CL = 35 pF VS = 3 V/0 V; see Figure 21 RL = 50 , CL = 35 pF VS = 3 V; see Figure 21 RL = 50 , CL = 35 pF VS1 = VS2 = 1.5 V; see Figure 22 VS = 1.5 V, RS = 0 , CL = 1 nF; see Figure 23 RL = 50 , CL = 5 pF, f = 100 kHz; see Figure 24 S1A-S2A/S1B-S2B, RL = 50 , CL = 5 pF, f = 100 kHz; see Figure 27 S1A-S1B/S2A-S2B, RL = 50 , CL = 5 pF, f = 100 kHz; see Figure 25 RL = 32 , f = 20 Hz to 20 kHz, VS = 3.5 V p-p RL = 50 , CL = 5 pF; see Figure 26 RL = 50 , CL = 5 pF; see Figure 26 VDD = 5.5 V Digital inputs = 0 V or 5.5 V Temperature range of the B version is -40C to +85C. Guaranteed by design, not subject to production test. Rev. A | Page 3 of 16 ADG884 VDD = 3.4 V to 4.2 V; GND = 0 V, unless otherwise noted. 1 Table 3. Parameter ANALOG SWITCH Analog Signal Range On Resistance, RON On Resistance Match Between Channels, RON On Resistance Flatness, RFLAT (ON) LEAKAGE CURRENTS Source Off Leakage, IS (OFF) Channel On Leakage, ID, IS (ON) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS 2 tON tOFF Break-Before-Make Time Delay, tBBM Charge Injection Off Isolation Channel-to-Channel Crosstalk 25C -40C to +85C 0 V to VDD 0.33 0.38 0.013 0.042 0.13 0.155 0.2 0.2 2.0 0.8 0.005 0.1 2 42 50 15 21 17 100 -60 -120 -60 Total Harmonic Distortion, THD + N Insertion Loss -3 dB Bandwidth CS (OFF) CD, CS (ON) POWER REQUIREMENTS IDD 0.01 -0.03 18 110 300 0.003 1 1 2 Unit V typ max typ max typ max nA typ nA typ V min V max A typ A max pF typ ns typ ns max ns typ ns max ns typ ns min pC typ dB typ dB typ dB typ % dB typ MHz typ pF typ pF typ A typ A max Test Conditions/Comments 0.45 0.065 0.175 VDD = 3.4 V, VS = 0 V to VDD, IS = 100 mA See Figure 18 VDD = 3.4 V, VS = 2 V, IS = 100 mA VDD = 3.4 V, VS = 0 V to VDD IS = 100 mA VDD = 4.2 V VS = 0.6 V/3.9 V, VD = 3.9 V/0.6 V; see Figure 19 VS = VD = 0.6 V or 3.9 V; see Figure 20 VIN = VINL or VINH 54 24 10 RL = 50 , CL = 35 pF VS = 1.5 V/0 V; see Figure 21 RL = 50 , CL = 35 pF VS = 1.5 V; see Figure 21 RL = 50 , CL = 35 pF VS1 = VS2 = 1.5 V; see Figure 22 VS = 1.5 V, RS = 0 , CL = 1 nF; see Figure 23 RL = 50 , CL = 5 pF, f = 100 kHz; see Figure 24 S1A-S2A/S1B-S2B, RL = 50 , CL = 5 pF, f = 100 kHz; see Figure 27 S1A-S1B/S2A-S2B, RL = 50 , CL = 5 pF, f = 100 kHz; see Figure 25 RL = 32 , f = 20 Hz to 20 kHz, VS = 2 V p-p RL = 50 , CL = 5 pF; see Figure 26 RL = 50 , CL = 5 pF; see Figure 26 VDD = 4.2 V Digital inputs = 0 V or 4.2 V Temperature range of the B version is -40C to +85C. Guaranteed by design, not subject to production test. Rev. A | Page 4 of 16 ADG884 VDD = 2.7 V to 3.6 V, GND = 0 V, unless otherwise noted. 1 Table 4. Parameter ANALOG SWITCH Analog Signal Range On Resistance, RON On Resistance Match Between Channels, RON On Resistance Flatness, RFLAT (ON) LEAKAGE CURRENTS Source Off Leakage, IS (OFF) Channel On Leakage, ID, IS (ON) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINL or IINH Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS 2 tON tOFF Break-Before-Make Time Delay, tBBM Charge Injection Off Isolation Channel-to-Channel Crosstalk 25C -40C to +85C 0 V to VDD 0.4 0.5 0.02 0.07 0.18 0.6 0.1 0.25 0.2 0.2 1.3 0.8 0.005 0.1 2 42 56 14 19 24 85 -60 -120 -60 Total Harmonic Distortion, THD + N Insertion Loss -3 dB Bandwidth CS (OFF) CD, CS (ON) POWER REQUIREMENTS IDD 0.03 -0.03 18 110 300 0.003 1 1 2 Unit V typ max typ max typ max nA typ nA typ V min V max A typ A max pF typ ns typ ns max ns typ ns max ns typ ns min pC typ dB typ dB typ dB typ % dB typ MHz typ pF typ pF typ A typ A max Test Conditions/Comments VDD = 2.7 V, VS = 0 V to VDD IS = 100 mA; see Figure 18 VDD = 2.7 V, VS = 0.6 V IS = 100 mA VDD = 2.7 V, VS = 0 V to VDD IS = 100 mA VDD = 3.6 V VS = 0.6 V/3.3 V, VD = 3.3 V/0.6 V, see Figure 19 VS = VD = 0.6 V or 3.3 V; see Figure 20 VIN = VINL or VINH 62 21 10 RL = 50 , CL = 35 pF VS = 1.5 V/0 V; see Figure 21 RL = 50 , CL = 35 pF VS = 1.5 V; see Figure 21 RL = 50 , CL = 35 pF VS1 = VS2 = 1.5 V; see Figure 22 VS = 1.25 V, RS = 0 , CL = 1 nF; see Figure 23 RL = 50 , CL = 5 pF, f = 100 kHz; see Figure 24 S1A-S2A/S1B-S2B, RL = 50 V, CL = 5 pF, f = 100 kHz; see Figure 27 S1A-S1B/S2A-S2B, RL = 50 , CL = 5 pF, f = 100 kHz; see Figure 25 RL = 32 , f = 20 Hz to 20 kHz, VS = 1.5 V p-p RL = 50 , CL = 5 pF; see Figure 26 RL = 50 , CL = 5 pF; see Figure 26 VDD = 3.6 V Digital inputs = 0 V or 3.6 V Temperature range of the B version is -40C to +85C. Guaranteed by design, not subject to production test. Rev. A | Page 5 of 16 ADG884 ABSOLUTE MAXIMUM RATINGS TA = 25C, unless otherwise noted. Table 5. Parameter VDD to GND Analog Inputs 1 Digital Inputs1 Peak Current, S or D 5 V Operation Continuous Current, S or D 5 V Operation Operating Temperature Range Industrial (B Version) Storage Temperature Range Junction Temperature 10-Lead MSOP Package JA Thermal Impedance JC Thermal Impedance 10-Lead WLCSP Package (4-Layer Board) JA Thermal Impedance 10-Lead LFCSP Package (4-Layer Board) JA Thermal Impedance JC Thermal Impedance IR Reflow, Peak Temperature <20 s 1 Rating -0.3 V to +6 V -0.3 V to VDD + 0.3 V -0.3 V to 6 V or 10 mA (whichever occurs first) 600 mA (pulsed at 1 ms, 10% duty cycle max) 400 mA -40C to +85C -65C to +150C 150C 206C/W 44C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Only one absolute maximum rating may be applied at any one time. 120C/W 76C/W 13.5C/W 235C Overvoltages at IN, S, or D are clamped by internal diodes. Current should be limited to the maximum ratings given. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. A | Page 6 of 16 ADG884 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS ADG884 TOP VIEW (Not to Scale) S1B 1 GND 2 S2B 3 IN1 10 IN2 4 D1 VDD 1 S1A 2 D1 3 IN1 4 S1B 5 10 S2A D2 5 9 ADG884 TOP VIEW (Not to Scale) 9 8 7 6 D2 IN2 05028-002 S1A 8 VDD 7 S2A 6 05028-003 S2B GND (SOLDER BUMPS ON OPPOSITE SIDE) Figure 2. LFCSP and MSOP Pin Configuration Figure 3. WLCSP Pin Configuration Table 6. Pin Function Descriptions LFCSP, MSOP 1 2 3 4 5 6 7 8 9 10 Pin No. WLCSP 7 8 9 10 1 2 3 4 5 6 Mnemonic VDD S1A D1 IN1 S1B GND S2B IN2 D2 S2A Description Most Positive Power Supply Potential. Source Terminal. May be an input or output. Drain Terminal. May be an input or output. Logic Control Input. Source Terminal. May be an input or output. Ground (0 V) Reference. Source Terminal. May be an input or output. Login Control Input. Drain Terminal. May be an input or output. Source Terminal. May be an input or output. Rev. A | Page 7 of 16 ADG884 TYPICAL PERFORMANCE CHARACTERISTICS 0.30 TA = 25C IDS = 100mA 0.25 4.5V 0.35 +85C 0.45 0.40 VDD = 3.3V IDS = 100mA ON RESISTANCE ON RESISTANCE 0.20 4.2V 0.30 +25C 0.25 0.20 0.15 0.10 -40C 0.15 5.5V 5V 0.10 0.05 05028-004 0.05 0 0 0.5 1.0 1.5 2.0 SIGNAL RANGE 2.5 0 0 1 2 3 SIGNAL RANGE 4 5 3.0 Figure 4. On Resistance vs. VD (VS), VDD = 4.2 V to 5.5 V 0.45 0.40 0.35 2.7V TA = 25C IDS = 100mA Figure 7. On Resistance vs. VD (VS) for Different Temperature, VDD = 3.3 V 5 4 3 VDD = 5V LEAKAGE CURRENT (nA) ON RESISTANCE 0.30 3V 0.25 3.3V 0.20 0.15 0.10 05028-005 2 ID, IS (ON) 1 0 -1 -2 -3 -4 -5 0 10 20 30 40 50 TEMPERATURE 60 70 80 05028-008 IS (OFF) 0.05 0 0 0.5 1.0 1.5 2.0 SIGNAL RANGE 2.5 3.0 Figure 5. On Resistance vs. VD (VS), VDD = 2.7 V to 3.3 V 0.35 VDD = 5V IDS = 100mA 4 5 Figure 8. Leakage Current vs. Temperature, VDD = 5 V VDD = 4.2V 0.30 0.25 LEAKAGE CURRENT (nA) ON RESISTANCE +85C 0.20 +25C 0.15 -40C 0.10 3 2 1 ID, IS (ON) 05028-006 IS (OFF) -1 0 10 20 30 40 50 TEMPERATURE 60 70 80 0 0 1 2 3 SIGNAL RANGE 4 5 Figure 6. On Resistance vs. VD (VS) for Different Temperature, VDD = 5 V Figure 9. Leakage Current vs. Temperature, VDD = 4.2 V Rev. A | Page 8 of 16 05028-009 0.05 0 05028-007 ADG884 4.0 3.5 3.0 VDD = 3.3V 0 -1 TA = 25C VDD = 5V/4.2V/3V LEAKAGE CURRENT (nA) -2 ATTENUATION (dB) 05028-026 2.5 2.0 1.5 1.0 0.5 0 -0.5 -1.0 0 10 20 30 40 50 TEMPERATURE 60 70 80 IS (OFF) ID, IS (ON) -3 -4 -5 -6 05028-022 -7 -8 0.03 0.10 1.00 10.00 FREQUENCY (MHz) 100.00 Figure 10. Leakage Current vs. Temperature, VDD = 3.3 V 600 TA = 25C 500 -10 0 Figure 13. Bandwidth TA = 25C VDD = 5V/4.2V/3V VDD = 5V -20 400 QINJ (pC) ATTENUATION (dB) -30 -40 -50 -60 300 VDD = 4.2V 200 100 0 0 0.5 1.0 1.5 2.0 2.5 3.0 VS (V) 3.5 4.0 4.5 5.0 -80 10 100 1k 10k 100k 1M FREQUENCY (MHz) 10M 100M Figure 11. Charge Injection vs. Source Voltage 50 TA = 25C -10 0 Figure 14. Off Isolation vs. Frequency TA = 25C VDD = 5V/4.2V/3V 40 VDD = 5V tON 30 ATTENUATION (dB) VDD = 3V -20 -30 -40 -50 -60 TIMES 20 tOFF 10 VDD = 3V VDD = 5V 05028-011 0 -40 -20 0 20 40 TEMPERATURE (C) 60 80 -80 10 100 1k 10k 100k 1M FREQUENCY (MHz) 10M 100M Figure 12. tON/tOFF Times vs. Temperature Figure 15. Crosstalk vs. Frequency Rev. A | Page 9 of 16 05028-024 -70 05028-023 05028-010 VDD = 3V -70 ADG884 0 -20 -40 TA = 25C VDD = 5V/4.2V/3V 0.10 0.09 0.08 ATTENUATION (dB) 0.07 THD + N (%) -60 -80 -100 -120 0.06 0.05 0.04 VDD = 3V, 1.5V p-p 0.03 0.02 VDD = 5V, 3.5V p-p 05028-027 05028-025 -140 -160 10 0.01 0 0 10 20 30 VDD = 4.2V, 2V p-p 40 50 60 70 FREQUENCY (kHz) 80 90 100 1k 10k 100k 1M FREQUENCY (MHz) 10M 100M 100 Figure 16. AC PSRR Figure 17. THD + N Rev. A | Page 10 of 16 ADG884 TERMINOLOGY IDD Positive supply current. VD (VS) Analog voltage on Terminals D, S. RON Ohmic resistance between D and S. RFLAT (ON) The difference between the maximum and minimum values of on resistance as measured on the switch. RON On resistance match between any two channels. IS (OFF) Source leakage current with the switch off. ID (OFF) Drain leakage current with the switch off. ID, IS (ON) Channel leakage current with the switch on. VINL Maximum input voltage for Logic 0. VINH Minimum input voltage for Logic 1. IINL (IINH) Input current of the digital input. CS (OFF) Off switch source capacitance. Measured with reference to ground. CD (OFF) Off switch drain capacitance. Measured with reference to ground. CD, CS (ON) On switch capacitance. Measured with reference to ground. CIN Digital input capacitance. tON Delay time between the 50% and 90% points of the digital input and switch on condition. tOFF Delay time between the 50% and 90% points of the digital input and switch off condition. tBBM On or off time measured between the 80% points of both switches when switching from one to another. Charge Injection Measure of the glitch impulse transferred from the digital input to the analog output during on-off switching. Off Isolation Measure of unwanted signal coupling through an off switch. Crosstalk Measure of unwanted signal that is coupled through from one channel to another as a result of parasitic capacitance. -3 dB Bandwidth Frequency at which the output is attenuated by 3 dB. On Response Frequency response of the on switch. Insertion Loss The loss due to the on resistance of the switch. THD + N Ratio of the harmonics amplitude plus noise of a signal to the fundamental. Rev. A | Page 11 of 16 ADG884 TEST CIRCUITS IDS V1 IS (OFF) ID (OFF) S D A 05028-013 S D A 05028-012 ID (ON) VD 05028-014 VS RON = V1/IDS VS VD NC S D A Figure 18. On Resistance Figure 19. Off Leakage Figure 20. On Leakage VDD 0.1F VDD VS S1B S1A D RL 50 GND VOUT CL 35pF VOUT VIN 50% 50% IN 90% 90% 05028-015 tON tOFF Figure 21. Switching Times, tON, tOFF VDD 0.1F 50% VDD VS S1B S1A D RL IN GND 50 VOUT CL 35pF VIN VOUT 80% 80% 0V 50% tBBM tBBM 05028-016 Figure 22. Break-Before-Make Time Delay, tBBM VDD SW ON S1B VS IN GND D S1A 1nF VOUT VOUT 05028-017 SW OFF VIN NC VOUT QINJ = CL x VOUT Figure 23. Charge Injection Rev. A | Page 12 of 16 ADG884 VDD 0.1F NETWORK ANALYZER 50 VS VOUT 05028-018 VDD 0.1F VDD VDD VOUT S1A RL 50 S1B 50 VS GND NC S1B D S1A 50 D RL 50 RL 50 GND OFF ISOLATION = 20 LOG VOUT VS CHANNEL-TO-CHANNEL CROSSTALK = 20 LOG VOUT VS Figure 24. Off Isolation VDD 0.1F NETWORK ANALYZER 50 VS D RL 50 VOUT 50 05028-019 Figure 26. Bandwidth VDD NETWORK ANALYZER VOUT 50 S2A S2B S1A S1B D2 S1B S1A D1 NC 50 GND VS 05028-020 NC INSERTION LOSS = 20 LOG VOUT WITH SWITCH VOUT WITHOUT SWITCH CHANNEL-TO-CHANNEL CROSSTALK = 20 LOG VOUT VS Figure 25. Channel-to-Channel Crosstalk (S1A-S1B) Figure 27. Channel-to-Channel Crosstalk (S1A-S2A) Rev. A | Page 13 of 16 05028-021 ADG884 OUTLINE DIMENSIONS INDEX AREA 3.00 BSC SQ 10 PIN 1 INDICATOR 1 3.00 BSC 10 6 1.50 BCS SQ TOP VIEW 0.50 BSC EXPOSED PAD (BOTTOM VIEW) 2.48 2.38 2.23 5 3.00 BSC 1 5 4.90 BSC PIN 1 6 0.50 BSC 0.95 0.85 0.75 0.15 0.00 0.27 0.17 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-BA 1.10 MAX 8 0 0.80 0.60 0.40 0.80 0.75 0.70 SEATING PLANE 0.80 MAX 0.55 TYP SIDE VIEW 0.50 0.40 0.30 0.05 MAX 0.02 NOM 0.20 REF 1.74 1.64 1.49 SEATING PLANE 0.23 0.08 0.30 0.23 0.18 Figure 28. 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 3 x 3 mm Body, Very Very Thin, Dual Lead (CP-10-9) Dimensions shown in millimeters Figure 29. 10-Lead Mini Small Outline Package [MSOP] (RM-10) Dimensions shown in millimeters 1.56 1.50 1.44 0.63 0.57 0.51 SEATING PLANE 0.36 0.32 0.28 C B A 1 BUMP 1 IDENTIFIER TOP VIEW (BUMP SIDE DOWN) 2.06 2.00 1.94 0.50 BSC BALL PITCH BOTTOM VIEW (BUMP SIDE UP) 2 3 4 0.26 0.22 0.18 0.11 0.09 0.07 Figure 30. 10-Ball Wafer Level Chip Scale Package [WLCSP] (CB-10) Dimensions shown in millimeters Rev. A | Page 14 of 16 ADG884 ORDERING GUIDE Model ADG884BRMZ 2 ADG884BRMZ-REEL2 ADG884BRMZ-REEL72 ADG884BCPZ-REEL2 ADG884BCPZ-REEL72 ADG884BCBZ-500RL72, 3 ADG884BCBZ-REEL2, 3 ADG884BCBZ-REEL72, 3 1 2 3 Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Description Mini Small Outline Package (MSOP) Mini Small Outline Package (MSOP) Mini Small Outline Package (MSOP) Lead Frame Chip Scale Package (LFCSP_WD) Lead Frame Chip Scale Package (LFCSP_WD) Micro Chip Scale Package (WLCSP) Micro Chip Scale Package (WLCSP) Micro Chip Scale Package (WLCSP) Package Option RM-10 RM-10 RM-10 CP-10-9 CP-10-9 CB-10 CB-10 CB-10 Branding 1 S9C S9C S9C S9C S9C S0W S0W S0W Branding on this package is limited to three characters due to space constraints. Z = Pb-free package. Contact Sales for availability; product under development. Rev. A | Page 15 of 16 ADG884 NOTES (c) 2005 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05028-0-6/05(A) Rev. A | Page 16 of 16 |
Price & Availability of ADG884BRMZ-REEL7
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |