Part Number Hot Search : 
AN435 MAX14503 AN1778 OSO5G 101M10 IRF843 ON2527 HK160
Product Description
Full Text Search
 

To Download IDT82V2088 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 OCTAL CHANNEL T1/E1/J1 LONG HAUL/ SHORT HAUL LINE INTERFACE UNIT
PRELIMINARY IDT82V2088
FEATURES:
* * * * * * Eight channel T1/E1/J1 long haul/short haul line interfaces Supports HPS (Hitless Protection Switching) for 1+1 protection without external relays Receiver sensitivity exceeds -36 dB@772KHz and -43 dB@1024 KHz Programmable T1/E1/J1 switchability allowing one bill of material for any line condition Single 3.3 V power supply with 5 V tolerance on digital interfaces Meets or exceeds specifications in - ANSI T1.102, T1.403 and T1.408 - ITU I.431, G.703,G.736, G.775 and G.823 - ETSI 300-166, 300-233 and TBR 12/13 - AT&T Pub 62411 Per channel software selectable on: - Wave-shaping templates for short haul and long haul LBO (Line Build Out) - Line terminating impedance (T1:100 , J1:110 , E1:75 /120 ) - Adjustment of arbitrary pulse shape - JA (Jitter Attenuator) position (receive path or transmit path) - Single rail/dual rail system interfaces - B8ZS/HDB3/AMI line encoding/decoding - Active edge of transmit clock (TCLK) and receive clock (RCLK) Active level of transmit data (TDATA) and receive data (RDATA) Receiver or transmitter power down High impedance setting for line drivers PRBS (Pseudo Random Bit Sequence) generation and detection with 215-1 PRBS polynomials for E1 - QRSS (Quasi Random Sequence Signals) generation and detection with 220-1 QRSS polynomials for T1/J1 - 16-bit BPV (Bipolar Pulse Violation)/Excess Zero/PRBS or QRSS error counter - Analog loopback, Digital loopback, Remote loopback and Inband loopback Per channel cable attenuation indication Adaptive receive sensitivity Non-intrusive monitoring per ITU G.772 specification Short circuit protection for line drivers LOS (Loss Of Signal) & AIS (Alarm Indication Signal) detection JTAG interface Supports serial control interface, Motorola and Intel Non-Multiplexed interfaces Package: IDT82V2088: 208-pin PQFP and 208-pin PBGA -
*
* * * * * * * *
DESCRIPTION:
The IDT82V2088 can be configured as an octal T1, octal E1 or octal J1 Line Interface Unit. In receive path, an Adaptive Equalizer is integrated to remove the distortion introduced by the cable attenuation. The IDT82V2088 also performs clock/data recovery, AMI/B8ZS/HDB3 line decoding and detects and reports the LOS conditions. In transmit path, there is an AMI/ B8ZS/HDB3 encoder, Waveform Shaper and LBOs. There is one Jitter Attenuator for each channel, which can be placed in either the receive path or the transmit path. The Jitter Attenuator can also be disabled. The IDT82V2088 supports both Single Rail and Dual Rail system interfaces and both serial and parallel control interfaces. To facilitate the network maintenance, a PRBS/QRSS generation/detection circuit is integrated in each channel, and different types of loopbacks can be set on a per channel basis. Four different kinds of line terminating impedance, 75, 100 , 110 and 120 are selectable on a per channel basis. The chip also provides driver short-circuit protection and supports JTAG boundary scanning. The IDT82V2088 can be used in SDH/SONET, LAN, WAN, Routers, Wireless Base Stations, IADs, IMAs, IMAPs, Gateways, Frame Relay Access Devices, CSU/DSU equipment, etc.
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGES
1
JUNE 2003
DSC-6043/2
2003 Integrated Device Technology, Inc. All rights reserved. Product specification is subject to change without notice.
One of the Eight Identical Channels
LOS/AIS Detector RTIPn RRINGn
LOSn
FUNCTIONAL BLOCK DIAGRAM
RCLKn RDn/RDPn CVn/RDNn Jitter Attenuator Data Slicer Adaptive Equalizer
B8ZS/ HDB3/AMI Decoder
Clock and Data Recovery
Receiver Internal Termination
PRBS Detector IBLC Detector
Remote Loopback
Digital Loopback
Analog Loopback
TTIPn Transmitter Internal Termination TRINGn
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Figure-1 Block Diagram
2
Microprocessor Interface Basic Control RST REF THZ SCLKE INT/MOT P/S A[7:0] D[7:0] INT SDO SDI/R/W/WR DS/RD SCLK CS MCLKS
TCLKn TDn/TDPn TDNn Jitter Attenuator Line Driver Waveform Shaper/LBO
B8ZS/ HDB3/AMI Encoder
PRBS Generator IBLC Generator TAOS
Clock Generator
JTAG TAP
VDDD VDDIO VDDA VDDT VDDR TDO TDI TMS TCK TRST
G.772 Monitor
MCLK
INDUSTRIAL TEMPERATURE RANGES
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
TABLE OF CONTENTS
1 2 3 IDT82V2088 PIN CONFIGURATIONS .......................................................................................... 8 PIN DESCRIPTION ..................................................................................................................... 10 FUNCTIONAL DESCRIPTION .................................................................................................... 16 3.1 T1/E1/J1 MODE SELECTION .......................................................................................... 16 3.2 TRANSMIT PATH ............................................................................................................. 16 3.2.1 TRANSMIT PATH SYSTEM INTERFACE.............................................................. 16 3.2.2 ENCODER .............................................................................................................. 16 3.2.3 PULSE SHAPER .................................................................................................... 16 3.2.3.1 Preset Pulse Templates .......................................................................... 16 3.2.3.2 LBO (Line Build Out) ............................................................................... 17 3.2.3.3 User-Programmable Arbitrary Waveform ................................................ 17 3.2.4 TRANSMIT PATH LINE INTERFACE..................................................................... 21 3.2.5 TRANSMIT PATH POWER DOWN ........................................................................ 21 3.3 RECEIVE PATH ............................................................................................................... 22 3.3.1 RECEIVE INTERNAL TERMINATION.................................................................... 22 3.3.2 LINE MONITOR ...................................................................................................... 23 3.3.3 ADAPTIVE EQUALIZER......................................................................................... 23 3.3.4 RECEIVE SENSITIVITY ......................................................................................... 23 3.3.5 DATA SLICER ........................................................................................................ 23 3.3.6 CDR (Clock & Data Recovery)................................................................................ 23 3.3.7 DECODER .............................................................................................................. 23 3.3.8 RECEIVE PATH SYSTEM INTERFACE ................................................................ 23 3.3.9 RECEIVE PATH POWER DOWN........................................................................... 23 3.3.10 G.772 NON-INTRUSIVE MONITORING ................................................................ 24 3.4 JITTER ATTENUATOR .................................................................................................... 25 3.4.1 JITTER ATTENUATION FUNCTION DESCRIPTION ............................................ 25 3.4.2 JITTER ATTENUATOR PERFORMANCE ............................................................. 25 3.5 LOS AND AIS DETECTION ............................................................................................. 26 3.5.1 LOS DETECTION ................................................................................................... 26 3.5.2 AIS DETECTION .................................................................................................... 27 3.6 TRANSMIT AND DETECT INTERNAL PATTERNS ........................................................ 28 3.6.1 TRANSMIT ALL ONES ........................................................................................... 28 3.6.2 TRANSMIT ALL ZEROS......................................................................................... 28 3.6.3 PRBS/QRSS GENERATION AND DETECTION.................................................... 28 3.7 LOOPBACK ...................................................................................................................... 28 3.7.1 ANALOG LOOPBACK ............................................................................................ 28 3.7.2 DIGITAL LOOPBACK ............................................................................................. 28 3.7.3 REMOTE LOOPBACK............................................................................................ 28 3.7.4 INBAND LOOPBACK.............................................................................................. 30 3.7.4.1 Transmit Activate/Deactivate Loopback Code......................................... 30 3.7.4.2 Receive Activate/Deactivate Loopback Code.......................................... 30 3.7.4.3 Automatic Remote Loopback .................................................................. 30
3
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.8
3.9 3.10
3.11
3.12 3.13 3.14 3.15 3.16 4
ERROR DETECTION/COUNTING AND INSERTION ...................................................... 31 3.8.1 DEFINITION OF LINE CODING ERROR ............................................................... 31 3.8.2 ERROR DETECTION AND COUNTING ................................................................ 31 3.8.3 BIPOLAR VIOLATION AND PRBS ERROR INSERTION ...................................... 32 LINE DRIVER FAILURE MONITORING ........................................................................... 32 MCLK AND TCLK ............................................................................................................. 33 3.10.1 MASTER CLOCK (MCLK) ...................................................................................... 33 3.10.2 TRANSMIT CLOCK (TCLK).................................................................................... 33 MICROCONTROLLER INTERFACES ............................................................................. 34 3.11.1 PARALLEL MICROCONTROLLER INTERFACE................................................... 34 3.11.2 SERIAL MICROCONTROLLER INTERFACE ........................................................ 34 INTERRUPT HANDLING .................................................................................................. 35 GENERAL PURPOSE I/O ................................................................................................ 36 5V TOLERANT I/O PINS .................................................................................................. 36 RESET OPERATION ........................................................................................................ 36 POWER SUPPLY ............................................................................................................. 36
PROGRAMMING INFORMATION .............................................................................................. 37 4.1 REGISTER LIST AND MAP ............................................................................................. 37 4.2 REGISTER DESCRIPTION .............................................................................................. 39 4.2.1 GLOBAL REGISTERS............................................................................................ 39 4.2.2 JITTER ATTENUATION CONTROL REGISTER ................................................... 41 4.2.3 TRANSMIT PATH CONTROL REGISTERS........................................................... 41 4.2.4 RECEIVE PATH CONTROL REGISTERS ............................................................. 43 4.2.5 NETWORK DIAGNOSTICS CONTROL REGISTERS ........................................... 45 4.2.6 INTERRUPT CONTROL REGISTERS ................................................................... 48 4.2.7 LINE STATUS REGISTERS ................................................................................... 51 4.2.8 INTERRUPT STATUS REGISTERS ...................................................................... 54 4.2.9 COUNTER REGISTERS ........................................................................................ 55 4.2.10 TRANSMIT AND RECEIVE TERMINATION REGISTER ....................................... 56 IEEE STD 1149.1 JTAG TEST ACCESS PORT ........................................................................ 57 5.1 JTAG INSTRUCTIONS AND INSTRUCTION REGISTER ............................................... 58 5.2 JTAG DATA REGISTER ................................................................................................... 58 5.2.1 DEVICE IDENTIFICATION REGISTER (IDR) ........................................................ 58 5.2.2 BYPASS REGISTER (BR)...................................................................................... 58 5.2.3 BOUNDARY SCAN REGISTER (BSR) .................................................................. 58 5.2.4 TEST ACCESS PORT CONTROLLER .................................................................. 59 TEST SPECIFICATIONS ............................................................................................................ 61 MICROCONTROLLER INTERFACE TIMING CHARACTERISTICS ......................................... 73 7.1 SERIAL INTERFACE TIMING .......................................................................................... 73 7.2 PARALLEL INTERFACE TIMING ..................................................................................... 74
5
6 7
4
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
LIST OF TABLES
Table-1 Table-2 Table-3 Table-4 Table-5 Table-6 Table-7 Table-8 Table-9 Table-10 Table-11 Table-12 Table-13 Table-14 Table-15 Table-16 Table-17 Table-18 Table-19 Table-20 Table-21 Table-22 Table-23 Table-24 Table-25 Table-26 Table-27 Table-28 Table-29 Table-30 Table-31 Table-32 Table-33 Table-34 Table-35 Table-36 Table-37 Table-38 Table-39 Table-40 Pin Description .............................................................................................................. Transmit Waveform Value For E1 75 ........................................................................ Transmit Waveform Value For E1 120 ...................................................................... Transmit Waveform Value For T1 0~133 ft................................................................... Transmit Waveform Value For T1 133~266 ft............................................................... Transmit Waveform Value For T1 266~399 ft............................................................... Transmit Waveform Value For T1 399~533 ft............................................................... Transmit Waveform Value For T1 533~655 ft............................................................... Transmit Waveform Value For J1 0~655 ft ................................................................... Transmit Waveform Value For DS1 0 dB LBO.............................................................. Transmit Waveform Value For DS1 -7.5 dB LBO ......................................................... Transmit Waveform Value For DS1 -15.0 dB LBO ....................................................... Transmit Waveform Value For DS1 -22.5 dB LBO ....................................................... Impedance Matching for Transmitter ............................................................................ Impedance Matching for Receiver ................................................................................ Criteria of Starting Speed Adjustment........................................................................... LOS Declare and Clear Criteria for Short Haul Mode ................................................... LOS Declare and Clear Criteria for Long Haul Mode.................................................... AIS Condition ................................................................................................................ Criteria for Setting/Clearing the PRBS_S Bit ................................................................ EXZ Definition ............................................................................................................... Interrupt Event............................................................................................................... Global Register List and Map........................................................................................ Per Channel Register List and Map .............................................................................. ID: Chip Revision Register ............................................................................................ RST: Reset Register ..................................................................................................... GCF0: Global Configuration Register 0 ........................................................................ GCF1: Global Configuration Register 1 ........................................................................ INTCH: Interrupt Channel Indication Register............................................................... GPIO: General Purpose IO Pin Definition Register....................................................... JACF: Jitter Attenuator Configuration Register ............................................................. TCF0: Transmitter Configuration Register 0 ................................................................. TCF1: Transmitter Configuration Register 1 ................................................................. TCF2: Transmitter Configuration Register 2 ................................................................. TCF3: Transmitter Configuration Register 3 ................................................................. TCF4: Transmitter Configuration Register 4 ................................................................. RCF0: Receiver Configuration Register 0..................................................................... RCF1: Receiver Configuration Register 1..................................................................... RCF2: Receiver Configuration Register 2..................................................................... MAINT0: Maintenance Function Control Register 0......................................................
5
10 18 18 18 18 19 19 19 19 20 20 20 20 21 22 25 26 27 27 28 31 35 37 38 39 39 39 40 40 40 41 41 42 42 43 43 43 44 45 45
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-41 Table-42 Table-43 Table-44 Table-45 Table-46 Table-47 Table-48 Table-49 Table-50 Table-51 Table-52 Table-53 Table-54 Table-55 Table-56 Table-57 Table-58 Table-59 Table-60 Table-61 Table-62 Table-63 Table-64 Table-65 Table-66 Table-67 Table-68 Table-69 Table-70 Table-71 Table-72 Table-73 Table-74 Table-75 Table-76
MAINT1: Maintenance Function Control Register 1...................................................... MAINT2: Maintenance Function Control Register 2...................................................... MAINT3: Maintenance Function Control Register 3...................................................... MAINT4: Maintenance Function Control Register 4...................................................... MAINT5: Maintenance Function Control Register 5...................................................... MAINT6: Maintenance Function Control Register 6...................................................... INTM0: Interrupt Mask Register 0 ................................................................................. INTM1: Interrupt Mask Register 1 ................................................................................. INTES: Interrupt Trigger Edges Select Register ........................................................... STAT0: Line Status Register 0 (real time status monitor)............................................. STAT1: Line Status Register 1 (real time status monitor)............................................. INTS0: Interrupt Status Register 0 ................................................................................ INTS1: Interrupt Status Register 1 ................................................................................ CNT0: Error Counter L-byte Register 0......................................................................... CNT1: Error Counter H-byte Register 1 ........................................................................ TERM: Transmit and Receive Termination Configuration Register .............................. Instruction Register Description .................................................................................... Device Identification Register Description..................................................................... TAP Controller State Description .................................................................................. Absolute Maximum Rating ............................................................................................ Recommended Operation Conditions ........................................................................... Power Consumption...................................................................................................... DC Characteristics ........................................................................................................ E1 Receiver Electrical Characteristics .......................................................................... T1/J1 Receiver Electrical Characteristics...................................................................... E1 Transmitter Electrical Characteristics ...................................................................... T1/J1 Transmitter Electrical Characteristics.................................................................. Transmitter and Receiver Timing Characteristics ......................................................... Jitter Tolerance ............................................................................................................. Jitter Attenuator Characteristics .................................................................................... JTAG Timing Characteristics ........................................................................................ Serial Interface Timing Characteristics ......................................................................... Non_multiplexed Motorola Read Timing Characteristics .............................................. Non_multiplexed Motorola Write Timing Characteristics .............................................. Non_multiplexed Intel Read Timing Characteristics ..................................................... Non_multiplexed Intel Write Timing Characteristics......................................................
46 46 46 47 47 47 48 49 50 51 53 54 55 55 55 56 58 58 59 61 61 62 62 63 64 65 66 67 68 70 72 73 74 75 76 77
6
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
LIST OF FIGURES
Figure-1 Figure-2 Figure-3 Figure-4 Figure-5 Figure-6 Figure-7 Figure-8 Figure-9 Figure-10 Figure-11 Figure-12 Figure-13 Figure-14 Figure-15 Figure-16 Figure-17 Figure-18 Figure-19 Figure-20 Figure-21 Figure-22 Figure-23 Figure-24 Figure-25 Figure-26 Figure-27 Figure-28 Figure-29 Figure-30 Figure-31 Figure-32 Figure-33 Figure-34 Figure-35 Figure-36 Figure-37 Block Diagram ................................................................................................................. 2 IDT82V2088 PQFP208 Package Pin Assignment .......................................................... 8 IDT82V2088 PBGA208 Package Pin Assignment (top view) ......................................... 9 E1 Waveform Template Diagram .................................................................................. 16 E1 Pulse Template Test Circuit ..................................................................................... 16 DSX-1 Waveform Template .......................................................................................... 16 T1 Pulse Template Test Circuit ..................................................................................... 17 Receive Path Function Block Diagram .......................................................................... 22 Transmit/Receive Line Circuit ....................................................................................... 22 Monitoring Receive Line in Another Chip ...................................................................... 23 Monitor Transmit Line in Another Chip .......................................................................... 23 G.772 Monitoring Diagram ............................................................................................ 24 Jitter Attenuator ............................................................................................................. 25 LOS Declare and Clear ................................................................................................. 26 Analog Loopback .......................................................................................................... 29 Digital Loopback ............................................................................................................ 29 Remote Loopback ......................................................................................................... 29 Auto Report Mode ......................................................................................................... 31 Manual Report Mode ..................................................................................................... 32 TCLK Operation Flowchart ............................................................................................ 33 Serial Processor Interface Function Timing .................................................................. 34 JTAG Architecture ......................................................................................................... 57 JTAG State Diagram ..................................................................................................... 60 Transmit System Interface Timing ................................................................................ 68 Receive System Interface Timing ................................................................................. 68 E1 Jitter Tolerance Performance .................................................................................. 69 T1/J1 Jitter Tolerance Performance .............................................................................. 69 E1 Jitter Transfer Performance ..................................................................................... 71 T1/J1 Jitter Transfer Performance ................................................................................ 71 JTAG Interface Timing .................................................................................................. 72 Serial Interface Write Timing ......................................................................................... 73 Serial Interface Read Timing with SCLKE=1 ................................................................ 73 Serial Interface Read Timing with SCLKE=0 ................................................................ 73 Non_multiplexed Motorola Read Timing ....................................................................... 74 Non_multiplexed Motorola Write Timing ....................................................................... 75 Non_multiplexed Intel Read Timing .............................................................................. 76 Non_multiplexed Intel Write Timing .............................................................................. 77
7
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
1
IDT82V2088 PIN CONFIGURATIONS
TCLK1 TD1/TDP1 TDN1 RCLK1 RD1/RDP1 CV1/RDN1 TCLK2 TD2/TDP2 TDN2 RCLK2 RD2/RDP2 CV2/RDN2 TCLK3 TD3/TDP3 TDN3 RCLK3 RD3/RDP3 CV3/RDN3 TCLK4 TD4/TDP4 TDN4 RCLK4 RD4/RDP4 VDDD CV4/RDN4 GNDD GNDIO TCLK5 VDDIO TD5/TDP5 TDN5 RCLK5 RD5/RDP5 CV5/RDN5 TCLK6 TD6/TDP6 TDN6 RCLK6 RD6/RDP6 CV6/RDN6 TCLK7 TD7/TDP7 TDN7 RCLK7 RD7/RDP7 CV7/RDN7 TCLK8 TD8/TDP8 TDN8 RCLK8 RD8/RDP8 CV8/RDN8 GNDIO VDDIO NC NC VDDT1 VDDT1 TRING1 TTIP1 GNDT1 GNDT1 GNDR1 RRING1 RTIP1 VDDR1 VDDR2 RTIP2 RRING2 GNDR2 GNDT2 GNDT2 TTIP2 TRING2 VDDT2 VDDT2 VDDT3 VDDT3 TRING3 TTIP3 GNDT3 GNDT3 GNDR3 RRING3 RTIP3 VDDR3 VDDR4 RTIP4 RRING4 GNDR4 GNDT4 GNDT4 TTIP4 TRING4 VDDT4 VDDT4 VDDA NC GNDA TRST TMS TDI TDO TCK 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53
IDT82V2088
GNDIO VDDIO NC NC VDDT8 VDDT8 TRING8 TTIP8 GNDT8 GNDT8 GNDR8 RRING8 RTIP8 VDDR8 VDDR7 RTIP7 RRING7 GNDR7 GNDT7 GNDT7 TTIP7 TRING7 VDDT7 VDDT7 VDDT6 VDDT6 TRING6 TTIP6 GNDT6 GNDT6 GNDR6 RRING6 RTIP6 VDDR6 VDDR5 RTIP5 RRING5 GNDR5 GNDT5 GNDT5 TTIP5 TRING5 VDDT5 VDDT5 VDDA REF IC GNDA MCLKS IC GPIO0 GPIO1
LOS1 NC LOS2 LOS3 LOS4 LOS5 LOS6 LOS7 LOS8 THZ SCLKE INT/MOT IC P/S VDDD NC MCLK NC GNDD GNDIO NC VDDIO NC D7 D6 D5 D4 D3 D2 D1 D0 NC VDDIO IC GNDIO NC A7 A6 A5 A4 A3 A2 A1 A0 CS SCLK DS/RD SDI/R/W/WR SDO INT RST NC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
Figure-2 IDT82V2088 PQFP208 Package Pin Assignment
8
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
IDT82V2088 PIN CONFIGURATIONS (CONTINUED)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A
GNDA
GNDT4
TTIP4
VDDT4
RTIP4
TRST
GNDT2
TTIP2
VDDT2
TCK
RTIP2
GNDT1
TTIP1
VDDT1
TCLK1
RCLK1
A
B
SCLKE
GNDT4
TRING4
VDDT4
RRING4
TMS
GNDT2
TRING2
VDDT2
TDO
RRING2
GNDT1
TRING1
VDDT1
TD1/ TDP1
RD1/ RDP1
B
C
VDDA
LOS1
LOS2
VDDR4
RTIP3
GNDR4
GNDT3
TTIP3
VDDT3
VDDR2
RTIP1
GNDR2
NC
TDN1
CV1/ RDN1
TCLK2
C
D
LOS3
LOS4
LOS5
VDDR3
RRING3
GNDR3
GNDT3
TRING3
VDDT3
VDDR1
RRING1
GNDR1
TDI
TDN2
TD2/ TDP2
RCLK2
D
E
LOS6
LOS7
LOS8
THZ
CV2/ RDN2
RD2/ RDP2
TD3/ TDP3
TCLK3
E
F
VDDD
INT/MOT
IC
GNDD
TDN3
CV3/ RDN3
RD3/ RDP3
RCLK3
F
G
MCLK
GPIO0
GPIO1
P/S
GNDA
NC
VDDIO
VDDIO
GNDD
TDN4
TD4/ TDP4
TCLK4
G
H
VDDIO
D6
D7
GNDIO
GNDA
GNDA
NC
NC
CV4/ RDN4
RD4/ RDP4
RCLK4
VDDD
H
J
D5
D4
D3
D2
GNDA
GNDA
GNDIO
GNDIO
GNDIO
TDN5
TD5/ TDP5
TCLK5
J
K
VDDIO
D0
D1
GNDIO
GNDA
GNDA
GNDA
GNDA
CV5/ RDN5
RD5/ RDP5
RCLK5
VDDIO
K
L
A7
A6
A5
A4
IC
TDN6
TD6/ TDP6
TCLK6
L
M
A0
A1
A2
A3
IDT82V2088
TDN7
CV6/ RDN6
RD6/ RDP6
RCLK6
M
N
CS
SCLK
DS/RD
VDDR6
RRING6
GNDR6
GNDT6
TRING6
VDDT6
VDDR8
RRING8
GNDR8
CV7/ RDN7
RD7/ RDP7
TD7/ TDP7
TCLK7
N
P
SDI/ R/W/WR
SDO
RST
VDDR5
RTIP6
GNDR5
GNDT6
TTIP6
VDDT6
VDDR7
RTIP8
GNDR7
IC
RD8/ RDP8
TDN8
RCLK7
P
R
INT
GNDT5
TRING5
VDDT5
RRING5
MCLKS
GNDT7
TRING7
VDDT7
IC
RRING7
GNDT8
TRING8
VDDT8
CV8/ RDN8
TD8/ TDP8
R
T
REF
GNDT5
TTIP5
VDDT5
RTIP5
GNDA
GNDT7
TTIP7
VDDT7
VDDA
RTIP7
GNDT8
TTIP8
VDDT8
RCLK8
TCLK8
T
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Figure-3 IDT82V2088 PBGA208 Package Pin Assignment (top view)
9
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
2
PIN DESCRIPTION
Name Type Pin No. PQFP208 TTIP1 TTIP2 TTIP3 TTIP4 TTIP5 TTIP6 TTIP7 TTIP8 TRING1 TRING2 TRING3 TRING4 TRING5 TRING6 TRING7 TRING8 RTIP1 RTIP2 RTIP3 RTIP4 RTIP5 RTIP6 RTIP7 RTIP8 RRING1 RRING2 RRING3 RRING4 RRING5 RRING6 RRING7 RRING8 164 177 184 197 64 77 84 97 163 178 183 198 63 78 83 98 169 172 189 192 69 72 89 92 168 173 188 193 68 73 88 93 PBGA208 Transmit and Receive Line Interface A13 A8 C8 A3 T3 P8 T8 T13 B13 B8 D8 B3 R3 N8 R8 R13 C11 A11 C5 A5 T5 P5 T11 P11 D11 B11 D5 B5 R5 N5 R11 N11 TTIPn1/TRINGn: Transmit Bipolar Tip/Ring for Channel 1~8 These pins are the differential line driver outputs and can be set to high impedance state globally or individually. A logic high on THZ pin turns all these pins into high impedance state. When THZ bit (TCF1, 03H...)2 is set to `1', the TTIPn/TRINGn in the corresponding channel is set to high impedance state. In summary, these pins will become high impedance in the following conditions: * THZ pin is high: all TTIPn/TRINGn enter high impedance; * THZn bit is set to 1: the corresponding TTIPn/TRINGn become high impedance; * Loss of MCLK: all TTIPn/TRINGn pins become high impedance;* * Loss of TCLKn: the corresponding TTIPn/TRINGn become HZ (exceptions: Remote Loopback; Transmit internal pattern by MCLK); * Transmitter path power down: the corresponding TTIPn/TRINGn become high impedance; * After software reset; pin reset and power on: all TTIPn/TRINGn enter high impedance. Description
Table-1 Pin Description
Output Analog
RTIPn/RRINGn: Receive Bipolar Tip/Ring for Channel 1~8 These pins are the differential line receiver inputs.
Input Analog
Notes: 1. The footprint `n' (n = 1~8) represents one of the eight channels. 2. The name and address of the registers that contain the preceding bit. Only the address of channel 1 register is listed, the rest addresses are represented by `...'. Users can find these omitted addresses in the Register Description section.
10
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name Type Pin No. PQFP208 TD1/TDP1 TD2/TDP2 TD3/TDP3 TD4/TDP4 TD5/TDP5 TD6/TDP6 TD7/TDP7 TD8/TDP8 Input TDN1 TDN2 TDN3 TDN4 TDN5 TDN6 TDN7 TDN8 TCLK1 TCLK2 TCLK3 TCLK4 TCLK5 TCLK6 TCLK7 TCLK8 RD1/RDP1 RD2/RDP2 RD3/RDP3 RD4/RDP4 RD5/RDP5 RD6/RDP6 RD7/RDP7 RD8/RDP8 CV1/RDN1 CV2/RDN2 CV3/RDN3 CV4/RDN4 CV5/RDN5 CV6/RDN6 CV7/RDN7 CV8/RDN8 RCLK1 RCLK2 RCLK3 RCLK4 RCLK5 RCLK6 RCLK7 RCLK8 154 148 142 136 126 120 114 108 156 150 144 138 129 122 116 110 152 146 140 134 124 118 112 106 151 145 139 132 123 117 111 105 153 147 141 135 125 119 113 107 C14 D14 F13 G14 J14 L14 M13 P15 A15 C16 E16 G16 J16 L16 N16 T16 B16 E14 F15 H14 K14 M15 N14 P14 C15 E13 F14 H13 K13 M14 N13 R15 A16 D16 F16 H15 K15 M16 P16 T15 155 149 143 137 127 121 115 109 PBGA208 Transmit and Receive Digital Data Interface B15 D15 E15 G15 J15 L15 N15 R16 TDn: Transmit Data for Channel 1~8 In Single Rail Mode, the NRZ data to be transmitted is input on these pins. Data on TDn is sampled into the device on the active edge of TCLKn. The active edge of TCLKn is selected by the TCLK_SEL bit (TCF0, 02H...). Data is encoded by AMI, HDB3 or B8ZS line code rules before being transmitted to the line. In this mode, TDNn should be connected to ground. TDPn/TDNn: Positive/Negative Transmit Data for Channel 1~8 In Dual Rail Mode, the NRZ data to be transmitted is input on these pins. Data on TDPn/TDNn is sampled into the device on the active edge of TCLKn. The active edge of the TCLKn is selected by the TCLK_SEL bit (TCF0, 02H...) The line code in Dual Rail Mode is as follows: TDPn 0 0 1 1 TDNn 0 1 0 1 Space Positive Pulse Negative Pulse Space Output Pulse Description
Input
TCLKn: Transmit Clock for Channel 1~8 These pins input 1.544 MHz for T1/J1 mode or 2.048 MHz for E1 mode transmit clock. The transmit data on TDn/TDPn or TDNn is sampled into the device on the active edge of TCLKn. If TCLKn is missing1 and the TCLKn missing interrupt is not masked, an interrupt will be generated.
RDn: Receive Data for Channel 1~8 In Single Rail Mode, the NRZ receive data is output on these pins. Data is decoded according to AMI, HDB3 or B8ZS line code rules. The active level on RDn pin is selected by the RD_INV bit (RCF0, 07H...). CVn: Code Violation for Channel 1~8 In Single Rail Mode, the BPV/CV errors in received data streams will be reported by driving pin CVn to high level for a full clock cycle. The B8ZS/HDB3 line code violation can be indicated when the B8ZS/ HDB3 decoder is enabled. When AMI decoder is selected, the bipolar violation can be indicated. RDPn/RDNn: Positive/Negative Receive Data for Channel 1~8 In Dual Rail Mode with Clock & Data Recovery (CDR), these pins output the NRZ data with the recovered clock. An active level on RDPn indicates the receipt of a positive pulse on RTIPn/RRINGn while an active level on RDNn indicates the receipt of a negative pulse on RTIPn/RRINGn. The active level on RDPn/RDNn is selected by the RD_INV bit (RCF0, 07H...). When CDR is disabled, these pins directly output the raw RZ sliced data. The output data on RDn and RDPn/RDNn is updated on the active edge of RCLKn. RCLKn: Receive Clock for Channel 1~8 These pins output 1.544 MHz for T1/J1 mode or 2.048 MHz for E1 mode receive clock. Under LOS conditions, if AISE bit (MAINT0, 0AH...) is `1', RCLKn is derived from MCLK. In clock recovery mode, these pins provide the clock recovered from the signal received on RTIPn/ RRINGn. The receive data (RDn in Single Rail Mode or RDPn/RDNn in Dual Rail Mode) is updated on the active edge of RCLKn. The active edge is selected by the RCLK_SEL bit (RCF0, 07H...). If clock recovery is bypassed, RCLKn is the exclusive OR(XOR) output of the Dual Rail sliced data RDPn and RDNn. This signal can be used in the applications with external clock recovery circuitry.
Output
Output
Notes: 1. TCLKn missing: the state of TCLKn continues to be high level or low level over 70 clock cycles.
11
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name MCLK Type Input 17 Pin No. PQFP208 PBGA208 G1 MCLK: Master Clock MCLK is an independent, free-running reference clock. It is a single reference for all operation modes and provides selectable1.544 MHz or 37.056 MHz for T1/J1 operating mode while 2.048 MHz or 49.152 MHz for E1 operating mode. The reference clock is used to generate several internal reference signals: * Timing reference for the integrated clock recovery unit. * Timing reference for the integrated digital jitter attenuator. * Timing reference for microcontroller interface. * Generation of RCLKn signal during a loss of signal condition. * Reference clock during Transmit All Ones (TAO) and all zeros condition. When sending PRBS/ QRSS or Inband Loopback code, either MCLK or TCLKn can be selected as the reference clock. * Reference clock for ATAO and AIS. The loss of MCLK will turn all the eight TTIP/TRING into high impedance status. MCLKS: Master Clock Select If 2.048 MHz (E1) or 1.544 MHz (T1/J1) is selected as the MCLK, this pin should be connected to ground; and if the 49.152 MHz (E1) or 37.056 MHz (T1/J1) is selected as the MCLK, this pin should be pulled high. LOSn: Loss of Signal Output for Channel 1~8 These pins are used to indicate the loss of received signals. When LOSn pin becomes high, it indicates the loss of received signals in channel n. The LOSn pin will become low automatically when valid received signal is detected again. The criteria of loss of signal are described in 3.5 LOS AND AIS DETECTION. Description
MCLKS
Input
56
R6
LOS1 LOS2 LOS3 LOS4 LOS5 LOS6 LOS7 LOS8 P/S
Output
1 3 4 5 6 7 8 9 14
C2 C3 D1 D2 D3 E1 E2 E3 G4
Control Interface Input P/S: Parallel or Serial Control Interface Select Level on this pin determines which control mode is selected to control the device as follows: P/S High Low Control Interface Parallel Microcontroller Interface Serial Microcontroller Interface
The serial microcontroller interface consists of CS, SCLK, SDI, SDO and SCLKE pins. Parallel microcontroller interface consists of CS, A[7:0], D[7:0], DS/RD, R/W/WR pins. The device supports non-multiplexed parallel interfaces as follows: P/S, INT/MOT 10 11 INT/MOT Input 12 F2 Microcontroller Interface Motorola non-multiplexed Intel non-multiplexed
INT/MOT: Intel or Motorola Microcontroller Interface Select In microcontroller mode, the parallel microcontroller interface is configured for Motorola compatible microcontrollers when this pin is low, or for Intel compatible microcontrollers when this pin is high. CS: Chip Select In serial and parallel microcontroller mode, this pin is asserted low by the microcontroller to enable microcontroller interface. For each read or write operation, this pin must be changed from high to low, and will remain low until the operation is over. SCLK: Shift Clock In serial microcontroller interface mode, signal on this pin is the shift clock for the serial interface. Configuration data on pin SDI is sampled on the rising edges of SCLK. Configuration and status data on pin SDO is clocked out of the device on the rising edges of SCLK if pin SCLKE is low, or on the falling edges of SCLK if pin SCLKE is high.
CS
Input
45
N1
SCLK
Input
46
N2
12
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name DS/RD Type Input 47 Pin No. PQFP208 PBGA208 N3 DS: Data Strobe In parallel Motorola microcontroller interface mode, signal on this pin is the data strobe of the parallel interface. During a write operation (R/W =0), data on D[7:0] is sampled into the device. During a read operation (R/W =1), data is output to D[7:0] from the device. RD: Read Operation In parallel Intel microcontroller interface mode, this pin is asserted low by the microcontroller to initiate a read cycle. Data is output to D[7:0] from the device during a read operation. SDI/R/W/WR Input 48 P1 SDI: Serial Data Input In serial microcontroller interface mode, data is input on this pin. Input data is sampled on the rising edges of SCLK. R/W: Read/Write Select In parallel Motorola microcontroller interface mode, this pin is low for write operation and high for read operation. WR: Write Operation In parallel Intel microcontroller interface mode, this pin is asserted low by the microcontroller to initiate a write cycle. Data on D[7:0] is sampled into the device during a write operation. SDO Output 49 P2 SDO: Serial Data Output In serial microcontroller interface mode, signal on this pin is the output data of the serial interface. Configuration and status data on pin SDO is clocked out of the device on the active edge of SCLK. INT: Interrupt Request This pin outputs the general interrupt request for all interrupt sources. If INTM_GLB bit (GCF0, 40H) is set to `1', all interrupt sources will be masked. And these interrupt sources also can be masked individually via registers (INTM0, 11H) and (INTM1, 12H). Interrupt status is reported via byte INT_CH (INTCH, 80H), registers (INTS0, 16H) and (INTS1, 17H). Output characteristics of this pin can be defined to be push-pull (active high or low) or be open-drain (active low) by bits INT_PIN[1:0] (GCF0, 40H). Dn: Data Bus 7~0 These pins function as a bi-directional data bus of the microcontroller interface. Description
INT
Output
50
R1
D7 D6 D5 D4 D3 D2 D1 D0 A7 A6 A5 A4 A3 A2 A1 A0 RST
I/O
24 25 26 27 28 29 30 31 37 38 39 40 41 42 43 44 51
H3 H2 J1 J2 J3 J4 K3 K2 L1 L2 L3 L4 M4 M3 M2 M1 P3
An: Address Bus 7~0 These pins function as an address bus of the microcontroller interface.
Input
Input
RST: Hardware Reset The chip is reset if a low signal is applied on this pin for more than 100ns. All the drivers output are in high impedance state, all the internal flip-flops are reset and all the registers are initialized to their default values. THZ: Transmit Driver Enable This pin enables or disables all transmitter drivers on a global basis. A low level on this pin enables the drivers while a high level turns all drivers into high impedance state. Note that functionality of internal circuits is not affected by signal on this pin. REF: Reference Resistor An external resistor (3 K, 1%) is used to connect this pin to ground to provide a standard reference current for internal circuit. 13
THZ
Input
10
E4
REF
Input
59
T1
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name SCLKE Type Input 11 Pin No. PQFP208 PBGA208 B1 SCLKE: Serial Clock Edge Select Signal on this pin determines the active edge of SCLK to output SDO. The active clock edge is selected as shown below: SCLKE Low High SCLK Rising edge is the active edge Falling edge is the active edge Description
JTAG Signals TRST Input Pullup 204 A6 TRST: JTAG Test Port Reset This is the active low asynchronous reset to the JTAG Test Port. This pin has an internal pull-up resistor. To ensure deterministic operation of the test logic, TMS should be held high while the signal applied to TRST changes from low to high. For normal signal processing, this pin should be connected to ground. TMS: JTAG Test Mode Select This pin is used to control the test logic state machine and is sampled on the rising edges of TCK.TMS has an internal pullup resistor. TCK: JTAG Test Clock This pin is the input clock for JTAG. The data on TDI and TMS is clocked into the device on the rising edges of TCK while the data on TDO is clocked out of the device on the falling edges of TCK. When TCK is idle at a low level, all stored-state devices contained in the test logic will retain their state indefinitely. TDO: JTAG Test Data Output This is a tri-state output signal and used for reading all the serial configuration and test data from the test logic. The data on TDO is clocked out of the device on the falling edges of TCK. TDI: JTAG Test Data Input This pin is used for loading instructions and data into the test logic and has an internal pullup resistor. The data on TDI is clocked into the device on the rising edges of TCK. Power Supplies and Grounds VDDIO 22, 33 103, 128 158 20, 35 104, 130 157 161, 162 179, 180 181, 182 199, 200 61, 62 79, 80 81, 82 99, 100 165, 166 175, 176 185, 186 195,196 65, 66 75, 76 85, 86 95, 96 60, 201 G9, G10 H1, K1 K16 3.3V I/O Power Supply
TMS
Input Pullup
205
B6
TCK
Input
208
A10
TDO
Output
207
B10
TDI
Input Pullup
206
D13
GNDIO
-
H4, J9 I/O Ground J10, J13, K4 A14, B14 A9, B9 C9, D9 A4, B4 R4, T4 N9, P9 R9, T9 R14, T14 A12, B12 A7, B7 C7, D7 A2, B2 R2, T2 N7, P7 R7, T7 R12, T12 C1, T10 3.3V Power Supply for Transmitter Driver
VDDT1 VDDT2 VDDT3 VDDT4 VDDT5 VDDT6 VDDT7 VDDT8 GNDT1 GNDT2 GNDT3 GNDT4 GNDT5 GNDT6 GNDT7 GNDT8 VDDA
-
-
Analog Ground for Transmitter Driver
-
3.3V Analog Core Power Supply
14
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name GNDA Type 57, 203 Pin No. PQFP208 PBGA208 A1, T6 G7, H7 H8, J7 J8, K7 K8, K9 K10 F1, H16 F4, G13 D10 C10 D4 C4 P4 N4 P10 N10 D12 C12 D6 C6 P6 N6 P12 N12 G2 G3 R10 L13 P13 F3 C13, G8, H9,H10 Core Analog Ground Description
VDDD GNDD VDDR1 VDDR2 VDDR3 VDDR4 VDDR5 VDDR6 VDDR7 VDDR8 GNDR1 GNDR2 GNDR3 GNDR4 GNDR5 GNDR6 GNDR7 GNDR8 GPIO0 GPIO1 IC IC NC
-
15, 133 19, 131 170 171 190 191 70 71 90 91 167 174 187 194 67 74 87 94 54 53 34 58 55 13 2, 16 18, 21 23, 32 36, 52 101, 102 159,160 202
3.3V Digital Core Power Supply Core Digital Ground 3.3V Power Supply for Receiver
-
Analog Ground for Receiver
I/O
GPIO: General Purpose IO Others
-
IC: Internal Connection Internal Use. These pins should be left open when in normal operation. IC: Internal Connection Internal Use. These pins should be connected to ground when in normal operation. NC: No Connection
15
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3
3.1
FUNCTIONAL DESCRIPTION
T1/E1/J1 MODE SELECTION
The IDT82V2088 can be used as an eight-channel E1 LIU or an eightchannel T1/J1 LIU. In E1 application, the T1E1 bit (GCF0, 40H) should be set to `0'. In T1/J1 application, the T1E1 bit should be set to `1'.
bits (TCF1, 03H...) should be set to `0000'; if the cable impedance is 120 , the PULS[3:0] bits (TCF1, 03H...) should be set to `0001'. In external impedance matching mode, for both E1/75 and E1/120 cable impedance, PULS[3:0] should be set to `0001'.
1 .2 0
3.2
TRANSMIT PATH
Normalized Amplitude
1 .0 0
The transmit path of each channel of the IDT82V2088 consists of an Encoder, an optional Jitter Attenuator, a Waveform Shaper, a set of LBOs, a Line Driver and a Programmable Transmit Termination. 3.2.1 TRANSMIT PATH SYSTEM INTERFACE The transmit path system interface consists of TCLKn pin, TDn/TDPn pin and TDNn pin. In E1 mode, the TCLKn is a 2.048 MHz clock. In T1/J1 mode, the TCLKn is a 1.544 MHz clock. If the TCLKn is missing for more than 70 MCLK cycles, an interrupt will be generated if it is not masked. Transmit data is sampled on the TDn/TDPn and TDNn pins by the active edge of TCLKn. The active edge of TCLKn can be selected by the TCLK_SEL bit (TCF0, 02H...). And the active level of the data on TDn/TDPn and TDNn can be selected by the TD_INV bit (TCF0, 02H...). The transmit data from the system side can be provided in two different ways: Single Rail and Dual Rail. In Single Rail mode, only TDn pin is used for transmitting data and the T_MD[1] bit (TCF0, 02H...) should be set to `0'. In Dual Rail Mode, both TDPn and TDNn pins are used for transmitting data, the T_MD[1] bit (TCF0, 02H...) should be set to `1'. 3.2.2 ENCODER When T1/J1 mode is selected, in Single Rail mode, the Encoder can be selected to be a B8ZS encoder or an AMI encoder by setting T_MD[0] bit (TCF0, 02H...). When E1 mode is selected, in Single Rail mode, the Encoder can be configured to be a HDB3 encoder or an AMI encoder by setting T_MD[0] bit (TCF0, 02H...). In both T1/J1 mode and E1 mode, when Dual Rail mode is selected (bit T_MD[1] is `1'), the Encoder is by-passed. In the Dual Rail mode, a logic `1' on the TDPn pin and a logic `0' on the TDNn pin results in a negative pulse on the TTIPn/TRINGn; a logic `0' on TDPn pin and a logic `1' on TDNn pin results in a positive pulse on the TTIPn/TRINGn. If both TDPn and TDNn are logic `1' or logic `0', the TTIPn/TRINGn outputs a space (Refer to TDn/ TDPn, TDNn Pin Description). 3.2.3 PULSE SHAPER The IDT82V2088 provides three ways of manipulating the pulse shape before sending it. The first is to use preset pulse templates for short haul application, the second is to use LBO (Line Build Out) for long haul application and the other way is to use user-programmable arbitrary waveform template. 3.2.3.1 Preset Pulse Templates For E1 applications, the pulse shape is shown in Figure-4 according to the G.703 and the measuring diagram is shown in Figure-5. In internal impedance matching mode, if the cable impedance is 75 , the PULS[3:0]
0 .8 0
0 .6 0
0 .4 0
0 .2 0
0 .0 0
-0 .2 0
-0 .6
- 0 .4
- 0 .2
0 T im e in U n it In te rv a ls
0 .2
0 .4
0 .6
Figure-4 E1 Waveform Template Diagram
TTIPn
IDT82V2088
TRINGn Note: 1. For RLOAD = 75 (nom), Vout (Peak)=2.37V (nom) 2. For RLOAD =120 (nom), Vout (Peak)=3.00V (nom)
RLOAD
VOUT
Figure-5 E1 Pulse Template Test Circuit For T1 applications, the pulse shape is shown in Figure-6 according to the T1.102 and the measuring diagram is shown in Figure-7. This also meets the requirement of G.703, 2001. The cable length is divided into five grades, and there are five pulse templates used for each of the cable length. The pulse template is selected by PULS[3:0] bits (TCF1, 03H...).
1.2 1 0.8 Normalized Amplitude 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 0 250 500 Time (ns) 750 1000 1250
Figure-6 DSX-1 Waveform Template
16
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
TTIPn Cable
IDT82V2088
TRINGn Note: RLOAD = 100 5%
RLOAD VOUT
Secondly, through the value of SCAL[5:0] bits increased or decreased by 1, the pulse amplitude can be scaled up or down at the percentage ratio against the standard pulse amplitude if needed. For different pulse shapes, the value of SCAL[5:0] bits and the scaling percentage ratio are different. The following twelve tables list these values. Do the followings step by step, the desired waveform can be programmed, based on the selected waveform template: (1).Select the UI by UI[1:0] bits (TCF3, 05H...) (2).Specify the sample address in the selected UI by SAMP [3:0] bits (TCF3, 05H...) (3).Write sample data to WDAT[6:0] bits (TCF4, 06H...). It contains the data to be stored in the RAM, addressed by the selected UI and the corresponding sample address. (4).Set the RW bit (TCF3, 05H...) to `0' to implement writing data to RAM, or to `1' to implement read data from RAM (5).Implement the Read from RAM/Write to RAM by setting the DONE bit (TCF3, 05H...) Repeat the above steps until all the sample data are written to or read from the internal RAM. (6).Write the scaling data to SCAL[5:0] bits (TCF2, 04H...) to scale the amplitude of the waveform based on the selected standard pulse amplitude When more than one UI is used to compose the pulse template, the overlap of two consecutive pulses could make the pulse amplitude overflow (exceed the maximum limitation) if the pulse amplitude is not set properly. This overflow is captured by DAC_OV_IS bit (INTS1, 17H...), and, if enabled by the DAC_OV_IM bit (INTM1, 12H...), an interrupt will be generated. The following tables give all the sample data based on the preset pulse templates and LBOs in detail for reference. For preset pulse templates and LBOs, scaling up/down against the pulse amplitude is not supported. 1.Table-2 Transmit Waveform Value For E1 75 2.Table-3 Transmit Waveform Value For E1 120 3.Table-4 Transmit Waveform Value For T1 0~133 ft 4.Table-5 Transmit Waveform Value For T1 133~266 ft 5.Table-6 Transmit Waveform Value For T1 266~399 ft 6.Table-7 Transmit Waveform Value For T1 399~533 ft 7.Table-8 Transmit Waveform Value For T1 533~655 ft 8.Table-9 Transmit Waveform Value For J1 0~655 ft 9.Table-10 Transmit Waveform Value For DS1 0 dB LBO 10.Table-11 Transmit Waveform Value For DS1 -7.5 dB LBO 11.Table-12 Transmit Waveform Value For DS1 -15.0 dB LBO 12.Table-13 Transmit Waveform Value For DS1 -22.5 dB LBO
Figure-7 T1 Pulse Template Test Circuit For J1 applications, the PULS[3:0] (TCF1, 03H...) should be set to `0111'. Table-14 lists these values. 3.2.3.2 LBO (Line Build Out) To prevent the cross-talk at the far end, the output of TTIP/TRING could be attenuated before transmission for long haul applications. The FCC Part 68 Regulations specifies four grades of attenuation with a step of 7.5 dB. Three LBOs are used to implement the pulse attenuation. The PULS[3:0] bits (TCF1, 03H...) are used to select the attenuation grade. Both Table-14 and Table-15 list these values. 3.2.3.3 User-Programmable Arbitrary Waveform When the PULS[3:0] bits are set to `11xx', user-programmable arbitrary waveform generator mode can be used in the corresponding channel. This allows the transmitter performance to be tuned for a wide variety of line condition or special application. Each pulse shape can extend up to 4 UIs (Unit Interval), addressed by UI[1:0] bits (TCF3, 05H...) and each UI is divided into 16 sub-phases, addressed by the SAMP[3:0] bits (TCF3, 05H...). The pulse amplitude of each phase is represented by a binary byte, within the range from +63 to 63, stored in WDAT[6:0] bits (TCF4, 06H...) in signed magnitude form. The most positive number +63 (D) represents the maximum positive amplitude of the transmit pulse while the most negative number -63 (D) represents the maximum negative amplitude of the transmit pulse. Therefore, up to 64 bytes are used. For each channel, a 64 bytes RAM is available. There are twelve standard templates which are stored in a local ROM. User can select one of them as reference and make some changes to get the desired waveform. User can change the wave shape and the amplitude to get the desired pulse shape. In order to do this, firstly, users can choose a set of waveform value from the following twelve tables, which is the most similar to the desired pulse shape. Table-2, Table-3, Table-4, Table-5, Table-6, Table-7, Table-8, Table-9, Table-10, Table-11, Table-12 and Table-13 list the sample data and scaling data of each of the twelve templates. Then modify the corresponding sample data to get the desired transmit pulse shape.
17
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-2 Transmit Waveform Value For E1 75
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0000000 0000000 0000000 0001100 0110000 0110000 0110000 0110000 0110000 0110000 0110000 0110000 0000000 0000000 0000000 0000000 UI 2 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 3 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 4 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000
Table-4 Transmit Waveform Value For T1 0~133 ft
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0010111 0100111 0100111 0100110 0100101 0100101 0100101 0100100 0100011 1001010 1001010 1001001 1000111 1000101 1000100 1000011 1101101 UI 2 1000010 1000001 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 3 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 4 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000
SCAL[5:0] = 100001 (default), One step change of this value of SCAL[5:0] results in 3% scaling up/down against the pulse amplitude.
Table-3 Transmit Waveform Value For E1 120
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0000000 0000000 0000000 0001111 0111100 0111100 0111100 0111100 0111100 0111100 0111100 0111100 0000000 0000000 0000000 0000000 UI 2 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 3 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 4 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000
SCAL[5:0] = (default), One step change of this value of SCAL[5:0] results in 2% scaling up/down against the pulse amplitude. 1. In T1 mode, when arbitrary pulse for short haul application is configured, users should write `110110' to SCAL[5:0] bits if no scaling is required.
Table-5 Transmit Waveform Value For T1 133~266 ft
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0011011 0101110 0101100 0101010 0101001 0101000 0100111 0100110 0100101 1010000 1001111 1001101 1001010 1001000 1000110 1000100 UI 2 1000011 1000010 1000001 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 See Table-4 UI 3 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 4 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000
SCAL[5:0] = 100001 (default), One step change of this value of SCAL[5:0] results in 3% scaling up/down against the pulse amplitude.
18
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-6 Transmit Waveform Value For T1 266~399 ft
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0011111 0110100 0101111 0101100 0101011 0101010 0101001 0101000 0100101 1010111 1010011 1010000 1001011 1001000 1000110 1000100 UI 2 1000011 1000010 1000001 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 See Table-4 UI 3 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 4 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000
Table-8 Transmit Waveform Value For T1 533~655 ft
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0100000 0111111 0111000 0110011 0101111 0101110 0101101 0101100 0101001 1011111 1011110 1010111 1001111 1001001 1000111 1000100 UI 2 1000011 1000010 1000001 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 See Table-4 UI 3 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 4 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000
Table-7 Transmit Waveform Value For T1 399~533 ft
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0100000 0111011 0110101 0101111 0101110 0101101 0101100 0101010 0101000 1011000 1011000 1010011 1001100 1001000 1000110 1000100 UI 2 1000011 1000010 1000001 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 See Table-4 UI 3 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 4 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000
Table-9 Transmit Waveform Value For J1 0~655 ft
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0011010 0100111 0100111 0100110 0100110 0100101 0100101 0100101 0100101 1001010 1001010 1001010 1000100 1000100 1000100 1000010 UI 2 1000010 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 3 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 4 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000
SCAL[5:0] = 110110 (default), One step change of this value of SCAL[5:0] results in 2% scaling up/down against the pulse amplitude.
19
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-10 Transmit Waveform Value For DS1 0 dB LBO
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0011010 0100111 0100111 0100110 0100110 0100101 0100101 0100101 0100101 1001010 1001010 1001010 1000100 1000100 1000100 1000010 UI 2 1000010 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 3 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 UI 4 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000
Table-12 Transmit Waveform Value For DS1 -15.0 dB LBO
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0000000 0000000 0000000 0000001 0000100 0001000 0001110 0010100 0011011 0100010 0101010 0110000 0110101 0110111 0111000 0110111 UI 2 0110101 0110011 0110000 0101101 0101010 0100111 0100100 0100001 0011110 0011100 0011010 0010111 0010101 0010100 0010010 0010000 UI 3 0001111 0001101 0001100 0001011 0001010 0001001 0001000 0000111 0000110 0000110 0000101 0000101 0000100 0000100 0000011 0000011 UI 4 0000011 0000010 0000010 0000010 0000010 0000001 0000001 0000001 0000001 0000001 0000001 0000001 0000001 0000000 0000000 0000000
SCAL[5:0] = 110110 (default), One step change of this Value results in 2% scaling up/down against the pulse amplitude.
SCAL[5:0] = 001000 (default), One step change of the value of SCAL[5:0] results in 12.5% scaling up/down against the pulse amplitude.
Table-11 Transmit Waveform Value For DS1 -7.5 dB LBO
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0000000 0000010 0001001 0010011 0011101 0100101 0101011 0110001 0110110 0111010 0111001 0110000 0101000 0100000 0011010 0010111 UI 2 0010100 0010010 0010000 0001110 0001100 0001011 0001010 0001001 0001000 0000111 0000110 0000101 0000100 0000100 0000011 0000011 UI 3 0000010 0000010 0000010 0000010 0000010 0000001 0000001 0000001 0000001 0000001 0000001 0000001 0000000 0000000 0000000 0000000 UI 4 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000 0000000
Table-13 Transmit Waveform Value For DS1 -22.5 dB LBO
Sample 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UI 1 0000001 0000011 0000101 0001000 0001100 0010001 0010110 0011011 0100001 0100110 0101010 0101110 0110001 0110011 0110100 0110100 UI 2 0110101 0110101 0110100 0110011 0110010 0110000 0101110 0101101 0101011 0101001 0100111 0100100 0100010 0100000 0011110 0011100 UI 3 0011011 0011001 0010111 0010101 0010100 0010010 0010001 0010000 0001110 0001101 0001100 0001011 0001010 0001001 0001000 0001000 UI 4 0000111 0000110 0000110 0000101 0000101 0000101 0000100 0000100 0000100 0000100 0000011 0000011 0000011 0000011 0000011 0000010
SCAL[5:0] = 010001 (default), One step change of this value of SCAL[5:0] results in 6.25% scaling up/down against the pulse amplitude.
SCAL[5:0] = 000100 (default), One step change of this value of SCAL[5:0] results in 25% scaling up/down against the pulse amplitude.
20
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.2.4
TRANSMIT PATH LINE INTERFACE
of the recommended impedance matching for transmitter. The TTIPn/TRINGn can be turned into high impedance globally by pulling THZ pin to high or individually by setting the THZ bit (TCF1, 03H...) to `1'. In this state, the internal transmit circuits are still active. Besides, in the following cases, TTIPn/TRINGn will also become high impedance: * Loss of MCLK: all TTIPn/TRINGn pins become high impedance;* * Loss of TCLKn: corresponding TTIPn/TRINGn become HZ (exceptions: Remote Loopback; Transmit internal pattern by MCLK); * Transmit path power down; * After software reset; pin reset and power on.
The transmit line interface consists of TTIPn pin and TRINGn pin. The impedance matching can be realized by the internal impedance matching circuit or the external impedance matching circuit. If T_TERM[2] is set to `0', the internal impedance matching circuit will be selected. In this case, the T_TERM[1:0] bits (TERM, 1AH...) can be set to choose 75 , 100 , 110 or 120 internal impedance of TTIPn/TRINGn. If T_TERM[2] is set to `1', the internal impedance matching circuit will be disabled. In this case, the external impedance matching circuit will be used to realize the impedance matching. For T1/J1 mode, the external impedance matching circuit for the transmitter is not supported. Figure-9 shows the appropriate external components to connect with the cable for one channel. Table-14 is the list
Table-14 Impedance Matching for Transmitter
Cable Configuration E1/75 E1/120 T1/0~133 ft T1/133~266 ft T1/266~399 ft T1/399~533 ft T1/533~655 ft J1/0~655 ft 0 dB LBO -7.5 dB LBO -15.0 dB LBO -22.5 dB LBO Note: The precision of the resistors should be better than 1% 011 010 000 001 010 Internal Termination T_TERM[2:0] PULS[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 RT 0 T_TERM[2:0] 1XX External Termination PULS[3:0] 0001 0001 RT 9.4
3.2.5
TRANSMIT PATH POWER DOWN
The transmit path can be powered down individually by setting the T_OFF bit (TCF0, 02H...) to `1'. In this case, the TTIPn/TRINGn pins are turned into high impedance.
21
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.3
RECEIVE PATH
The receive path consists of Receive Internal Termination, Monitor Gain, Amplitude/Wave Shape Detector, Digital Tuning Controller, Adaptive Equalizer, Data Slicer, CDR (Clock and Data Recovery), Optional Jitter Attenuator, Decoder and LOS/AIS Detector. Refer to Figure-8. 3.3.1 RECEIVE INTERNAL TERMINATION The impedance matching can be realized by the internal impedance matching circuit or the external impedance matching circuit. If R_TERM[2]
is set to `0', the internal impedance matching circuit will be selected. In this case, the R_TERM[1:0] bits (TERM, 1AH...) can be set to choose 75 , 100 , 110 or 120 internal impedance of RTIPn/RRINGn. If R_TERM[2] is set to `1', the internal impedance matching circuit will be disabled. In this case, the external impedance matching circuit will be used to realize the impedance matching. Figure-9 shows the appropriate external components to connect with the cable for one channel. Table-15 is the list of the recommended impedance matching for receiver.
LOS/AIS Detector
LOS
RTIP RRING
Receive Internal termination
Monitor Gain
Adaptive Equalizer
Data Slicer
Clock and Data Recovery
Jitter Attenuator
RCLK Decoder RDP RDN
Figure-8 Receive Path Function Block Diagram
Table-15 Impedance Matching for Receiver
Cable Configuration E1/75 E1/120 T1 J1 Internal Termination R_TERM[2:0] 000 001 010 011 RR 120 1XX External Termination R_TERM[2:0] RR 75 120 100 110
VDDRn
A
RX Line
1:1 ** RR
D8 * D7
One of the Eight Identical Channels RTIPn VDDRn 0.1F 3.3 V 68F 1 * 3.3 V 0.1F 68F 1
*
* *
B
* TX Line 2:1 * Cp
2
VDDRn D6 * * * D5 VDDTn D4 RT * * D3 VDDTn D2 RT D13
IDT82V2088
RRINGn TTIPn
GNDRn
VDDTn
* *
TRINGn
GNDTn
Note: 1. Common decoupling capacitor 2. Cp 0-560 (pF) 3. D1 - D8, Motorola - MBR0540T1;
International Rectifier - 11DQ04 or 10BQ060
Figure-9 Transmit/Receive Line Circuit
22
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.3.2
LINE MONITOR
In both T1/J1 and E1 short haul applications, the non-intrusive monitoring on channels located in other chips can be performed by tapping the monitored channel through a high impedance bridging circuit. Refer to Figure10 and Figure-11. After a high resistance bridging circuit, the signal arriving at the RTIPn/ RRINGn is dramatically attenuated. To compensate this attenuation, the Monitor Gain can be used to boost the signal by 22 dB, 26 dB and 32 dB, selected by MG[1:0] bits (RCF2, 09H...). For normal operation, the Monitor Gain should be set to 0 dB.
DSX cross connect point
RTIP
by UPDW[1:0] bits (RCF2, 09H...). A shorter observation period allows quicker response to pulse amplitude variation while a longer observation period can minimize the possible overshoots. The default observation period is 128 symbol periods. Based on the observed peak value for a period, the equalizer will be adjusted to achieve a normalized signal. LATT[4:0] bits (STAT1, 15H...) indicate the signal attenuation introduced by the cable in approximately 2 dB per step. 3.3.4 RECEIVE SENSITIVITY For short haul application, the Receive Sensitivity for both E1 and T1/ J1 is -10 dB. For long haul application, the receive sensitivity is -43 dB for E1 and -36 dB for T1/J1. 3.3.5 DATA SLICER The Data Slicer is used to generate a standard amplitude mark or a space according to the amplitude of the input signals. The threshold can be 40%, 50%, 60% or 70%, as selected by the SLICE[1:0] bits (RCF2, 09H...). The output of the Data Slicer is forwarded to the CDR (Clock & Data Recovery) unit or to the RDPn/RDNn pins directly if the CDR is disabled. 3.3.6 CDR (Clock & Data Recovery) The CDR is used to recover the clock from the received signals. The recovered clock tracks the jitter in the data output from the Data Slicer and keeps the phase relationship between data and clock during the absence of the incoming pulse. The CDR can also be by-passed in the Dual Rail mode. When CDR is by-passed, the data from the Data Slicer is output to the RDPn/RDNn pins directly. 3.3.7 DECODER In T1/J1 applications, the R_MD[1:0] bits (RCF0, 07H...) is used to select the AMI decoder or B8ZS decoder. In E1 applications, the R_MD[1:0] bits (RCF0, 07H...) are used to select the AMI decoder or HDB3 decoder. 3.3.8 RECEIVE PATH SYSTEM INTERFACE The receive path system interface consists of RCLKn pin, RDn/RDPn pin and RDNn pin. In E1 mode, the RCLKn outputs a recovered 2.048 MHz clock. In T1/J1 mode, the RCLKn outputs a recovered 1.544 MHz clock. The received data is updated on the RDn/RDPn and RDNn pins on the active edge of RCLKn. The active edge of RCLKn can be selected by the RCLK_SEL bit (RCF0, 07H...). And the active level of the data on RDn/ RDPn and RDNn can also be selected by the RD_INV bit (RCF0, 07H...). The received data can be output to the system side in two different ways: Single Rail or Dual Rail, as selected by R_MD bit [1] (RCF0, 07H...). In Single Rail mode, only RDn pin is used to output data and the RDNn/CVn pin is used to report the received errors. In Dual Rail Mode, both RDPn pin and RDNn pin are used for outputting data. In the receive Dual Rail mode, the CDR unit can be by-passed by setting R_MD[1:0] to `11' (binary). In this situation, the output data from the Data Slicer will be output to the RDPn/RDNn pins directly, and the RCLKn outputs the exclusive OR (XOR) of the RDPn and RDNn. 3.3.9 RECEIVE PATH POWER DOWN The receive path can be powered down individually by setting R_OFF bit (RCF0, 07H...) to `1'. In this case, the RCLKn, RDn/RDPn, RDPn and LOSn will be logic low.
23
monitor gain=0dB
RRING
R
normal receive mode
RTIP
monitor gain =22/26/32dB
RRING
monitor mode
Figure-10 Monitoring Receive Line in Another Chip
DSX cross connect point
TTIP
TRING
R
normal transmit mode
RTIP
monitor gain monitor gain =22/26/32dB
RRING
monitor mode
Figure-11 Monitor Transmit Line in Another Chip 3.3.3 ADAPTIVE EQUALIZER The adaptive equalizer can remove most of the signal distortion due to intersymbol interference caused by cable attenuation. It can be enabled or disabled by setting EQ_ON bit to `1' or `0' (RCF1, 08H...). When the adaptive equalizer is out of range, EQ_S bit (STAT0, 14H...) will be set to `1' to indicate the status of equalizer. If EQ_IES bit (INTES, 13H...) is set to `1', any changes of EQ_S bit will generate an interrupt and EQ_IS bit (INTS0, 16H...) will be set to `1' if it is not masked. If EQ_IES bit is set to `0', only the `0' to `1' transition of the EQ_S bit will generate an interrupt and EQ_IS bit will be set to `1' if it is not masked. The EQ_IS bit will be reset after being read. The Amplitude/wave shape detector keeps on measuring the amplitude/wave shape of the incoming signals during an observation period. This observation period can be 32, 64, 128 or 256 symbol periods, as selected
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.3.10 G.772 NON-INTRUSIVE MONITORING In applications using only seven channels, channel 1 can be configured to monitor the data received or transmitted in any one of the remaining channels. The MON[3:0] bits (GCF1, 60H) determine which channel and which direction (transmit/receive) will be monitored. The monitoring is non-intrusive per ITU-T G.772. Figure-12 illustrates the concept.
The monitored line signal (transmit or receive) goes through Channel 1's Clock and Data Recovery. The signal can be observed digitally at the RCLK1, RD1/RDP1 and RDN1. If Channel 1 is configured to Remote Loopback while in the Monitoring mode, the monitored data will be output on TTIP1/TRING1.
Channel N (N > 2)
LOSn LOS/AIS Detector B8ZS/ HDB3/AMI Decoder Clock and Data Recovery Receiver Internal Termination RTIPn RRINGn
RCLKn RDn/RDPn CVn/RDNn
Jitter Attenuator
Data Slicer
Adaptive Equalizer
TCLKn TDn/TDPn TDNn
B8ZS/ HDB3/AMI Encoder
Jitter Attenuator
Waveform Shaper/LBO
Line Driver
Transmitter Internal Termination
TTIPn TRINGn
Channel 1
LOS1 LOS/AIS Detector B8ZS/ HDB3/AMI Decoder Clock and Data Recovery Receiver Internal Termination
G.772 Monitor
RCLK1 RDn/RDP1 CVn/RDN1
Jitter Attenuator
Data Slicer
Adaptive Equalizer
RTIP1 RRING1
Remote Loopback
TCLK1 TDn/TDP1 TDN1 B8ZS/ HDB3/AMI Encoder Jitter Attenuator Waveform Shaper/LBO Line Driver Transmitter Internal Termination TTIP1 TRING1
Figure-12 G.772 Monitoring Diagram
24
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.4
JITTER ATTENUATOR
There is one Jitter Attenuator in each channel of the LIU. The Jitter Attenuator can be deployed in the transmit path or the receive path, and can also be disabled. This is selected by the JACF[1:0] bits (JACF, 01H...). 3.4.1 JITTER ATTENUATION FUNCTION DESCRIPTION The Jitter Attenuator is composed of a FIFO and a DPLL, as shown in Figure-13. The FIFO is used as a pool to buffer the jittered input data, then the data is clocked out of the FIFO by a de-jittered clock. The depth of the FIFO can be 32 bits, 64 bits or 128 bits, as selected by the JADP[1:0] bits (JACF, 01H...). Consequently, the constant delay of the Jitter Attenuator will be 16 bits, 32 bits or 64 bits. Deeper FIFO can tolerate larger jitter, but at the expense of increasing data latency time.
In E1 applications, the Corner Frequency of the DPLL can be 0.9 Hz or 6.8 Hz, as selected by the JABW bit (JACF, 01H...). In T1/J1 applications, the Corner Frequency of the DPLL can be 1.25 Hz or 5.00 Hz, as selected by the JABW bit (JACF, 01H...). The lower the Corner Frequency is, the longer time is needed to achieve synchronization. When the incoming data moves faster than the outgoing data, the FIFO will overflow. This overflow is captured by the JAOV_IS bit (INTS1, 17H...). If the incoming data moves slower than the outgoing data, the FIFO will underflow. This underflow is captured by the JAUD_IS bit (INTS1, 17H...). For some applications that are sensitive to data corruption, the JA limit mode can be enabled by setting JA_LIMIT bit (JACF, 01H...) to `1'. In the JA limit mode, the speed of the outgoing data will be adjusted automatically when the FIFO is close to its full or emptiness. The criteria of starting speed adjustment are shown in Table-16. The JA limit mode can reduce the possibility of FIFO overflow and underflow, but the quality of jitter attenuation is deteriorated. 3.4.2 JITTER ATTENUATOR PERFORMANCE The performance of the Jitter Attenuator in the IDT82V2088 meets the ITU-T I.431, G.703, G.736-739, G.823, G.824, ETSI 300011, ETSI TBR12/ 13, AT&T TR62411 specifications. Details of the Jitter Attenuator performance is shown in Table-69 Jitter Tolerance and Table-70 Jitter Attenuator Characteristics.
Jittered Data
FIFO 32/64/128
W R
RDn/RDPn De-jittered Data RDNn
Jittered Clock
DPLL
De-jittered Clock RCLKn
Table-16 Criteria of Starting Speed Adjustment
FIFO Depth Criteria for Adjusting Data Outgoing Speed 2 bits close to its full or emptiness 3 bits close to its full or emptiness 4 bits close to its full or emptiness 32 Bits 64 Bits 128 Bits
MCLK
Figure-13 Jitter Attenuator
25
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.5
3.5.1
LOS AND AIS DETECTION
LOS DETECTION
The Loss of Signal Detector monitors the amplitude of the incoming signal level and pulse density of the received signal on RTIPn and RRINGn. * LOS declare (LOS=1) A LOS is detected when the incoming signal has "no transitions", i.e., when the signal level is less than Q dB below nominal for N consecutive pulse intervals. Here N is defined by LAC bit (MAINT0, 0AH...). LOS will be declared by pulling LOSn pin to high (LOS=1) and LOS interrupt will be generated if it is not masked. * LOS clear (LOS=0) The LOS is cleared when the incoming signal has "transitions", i.e., when the signal level is greater than P dB below nominal and has an average pulse density of at least 12.5% for M consecutive pulse intervals, starting with the receipt of a pulse. Here M is defined by LAC bit (MAINT0, 0AH...). LOS status is cleared by pulling LOSn pin to low.
* LOS detect level threshold In short haul mode, the amplitude threshold Q is fixed on 800 mVpp, while P=Q+200 mVpp (200 mVpp is the LOS level detect hysteresis). In long haul mode, the value of Q can be selected by LOS[4:0] bit (RCF1, 08H...), while P=Q+4 dB (4 dB is the LOS level detect hysteresis). The LOS[4:0] default value is 10101 (-46 dB). * Criteria for declare and clear of a LOS detect The detection supports the ANSI T1.231 and I.431 for T1/J1 mode and G.775 and ETSI 300233/I.431 for E1 mode. The criteria can be selected by LAC bit (MAINT0, 0AH...) and T1E1 bit (GCF0, 40H). Table-17 and Table-18 summarize LOS declare and clear criteria for both short haul and long haul application. * All Ones output during LOS On the system side, the RDPn/RDNn will reflect the input pulse "transition" at the RTIPn/RRINGn side and output recovery clock (but the quality of the output clock can not be guaranteed when the input level is lower than the maximum receive sensitivity) when AISE bit (MAINT0, 0AH...) is 0; or output All Ones as AIS when AISE bit (MAINT0, 0AH...) is 1. In this case RCLKn output is replaced by MCLK. On the line side, the TTIPn/TRINGn will output All Ones as AIS when ATAO bit (MAINT0, 0AH...) is 1. The All Ones pattern uses MCLK as the reference clock.
LOS=1
signal level>P density=OK (observing windows= M)
signal levelLOS indicator is always active for all kinds of loopback modes.
LOS=0
Figure-14 LOS Declare and Clear
Table-17 LOS Declare and Clear Criteria for Short Haul Mode
Control bit T1E1 LAC Level < 800 mVpp N=175 bits 0=T1.231 1=T1/J1 Level < 800 mVpp N=1544 bits 1=I.431 Level < 800 mVpp N=32 bits 0=G.775 0=E1 Level < 800 mVpp N=2048 bits 1=I.431/ETSI Level > 1 Vpp M=128 bits 12.5% mark density <100 consecutive zeroes Level > 1 Vpp M=128 bits 12.5% mark density <100 consecutive zeroes Level > 1 Vpp M=32 bits 12.5% mark density <16 consecutive zeroes Level > 1 Vpp M=32 bits 12.5% mark density <16 consecutive zeroes LOS declare threshold LOS clear threshold
26
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-18 LOS Declare and Clear Criteria for Long Haul Mode
Control bit T1E1 LAC LOS[4:0] Q (dB) -4 -6 ... -38 ... -46 -48 -4 -16 -18 ... -30 -32 ... -38 ... -46 -48 -4 ... -8 -10 ... -36 -38 ... -46 -48 -4 -6 ... -20 -22 ... -46 -48 Level < Q N=2048 bits Level > Q+ 4dB M=32 bits 12.5% mark density <16 consecutive zeroes I.431 Level detect range is -6 to -20 dB. Level < Q N=32 bits Level > Q+ 4dB M=32 bits 12.5% mark density <16 consecutive zeroes G.775 Level detect range is -9 to -35 dB. Level < Q N=175 bits Level > Q+ 4dB M=128 bits 12.5% mark density <100 consecutive zeroes 00000 00001 ... T1.231 10001 ... 10101 10110-11111 1=T1/J1 00000 ... 00110 LOS declare threshold LOS clear threshold Note
0
Level < Q N=1544 bits
1
I.431 00111 ... 01101 01110 ... 10001 ... 10101 10110-11111 00000 ... 00010
Level > Q+ 4dB I.431 Level detect range is -18 to -30 dB. M=128 bits 12.5% mark density <100 consecutive zeroes
-
-
0
00011 G.775 ... 10000 10001 ... 10101(default) 10110-11111 00000 00001 I.431/ ... ETSI 01000 01001 ... 10101(default) 10110-11111
0=E1
1
3.5.2
AIS DETECTION
The Alarm Indication Signal can be detected by the IDT82V2088 when the Clock&Data Recovery unit is enabled. The status of AIS detection is reflected in the AIS_S bit (STAT0, 14H...). In T1/J1 applications, the criteria for declaring/clearing AIS detection are in compliance with the ANSI
T1.231. In E1 applications, the criteria for declaring/clearing AIS detection comply with the ITU G.775 or the ETSI 300233, as selected by the LAC bit (MAINT0, 0AH...). Table-19 summarizes different criteria for AIS detection Declaring/Clearing.
Table-19 AIS Condition
ITU G.775 for E1 (LAC bit is set to `0' by default) AIS detected AIS cleared ETSI 300233 for E1 (LAC bit is set to `1') ANSI T1.231 for T1/J1
Less than 3 zeros contained in each of two consecutive Less than 3 zeros contained in a 512-bit Less than 9 zeros contained in an 8192-bit stream 512-bit streams are received stream are received (a ones density of 99.9% over a period of 5.3ms) 3 or more zeros contained in each of two consecutive 3 or more zeros contained in a 512-bit 9 or more zeros contained in an 8192-bit stream 512-bit streams are received stream are received are received 27
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.6
TRANSMIT AND DETECT INTERNAL PATTERNS
The internal patterns (All Ones, All Zeros, PRBS/QRSS pattern and Activate/Deactivate Loopback Code) will be generated and detected by the IDT82V2088. TCLKn is used as the reference clock by default. MCLK can also be used as the reference clock by setting the PATT_CLK bit (MAINT0, 0AH...) to `1'. If the PATT_CLK bit (MAINT0, 0AH...) is set to `0' and the PATT[1:0] bits (MAINT0, 0AH...) are set to `00', the transmit path will operate in normal mode. 3.6.1 TRANSMIT ALL ONES In transmit direction, the All Ones data can be inserted into the data stream when the PATT[1:0] bits (MAINT0, 0AH...) are set to `01'. The transmit data stream is output from TTIPn/TRINGn. In this case, either TCLKn or MCLK can be used as the transmit clock, as selected by the PATT_CLK bit (MAINT0, 0AH...). 3.6.2 TRANSMIT ALL ZEROS If the PATT_CLK bit (MAINT0, 0AH...) is set to `1', the All Zeros will be inserted into the transmit data stream when the PATT[1:0] bits (MAINT0, 0AH...) are set to `00'. 3.6.3 PRBS/QRSS GENERATION AND DETECTION A PRBS/QRSS will be generated in the transmit direction and detected in the receive direction by IDT82V2088. The QRSS is 220-1 for T1/J1 applications and the PRBS is 215-1 for E1 applications, with maximum zero restrictions according to the AT&T TR62411 and ITU-T O.151. When the PATT[1:0] bits (MAINT0, 0AH...) are set to `10', the PRBS/ QRSS pattern will be inserted into the transmit data stream with the MSB first. The PRBS/QRSS pattern will be transmitted directly or invertedly. The PRBS/QRSS in the received data stream will be monitored. If the PRBS/QRSS has reached synchronization status, the PRBS_S bit (STAT0, 14H...) will be set to `1', even in the presence of a logic error rate less than or equal to 10-1. The criteria for setting/clearing the PRBS_S bit are shown in Table-20.
PRBS data can be inverted through setting the PRBS_INV bit (MAINT0, 0AH...). Any change of PRBS_S bit will be captured by PRBS_IS bit (INTS0, 16H...). The PRBS_IES bit (INTES, 13H...) can be used to determine whether the `0' to `1' change of PRBS_S bit will be captured by the PRBS_IS bit or any changes of PRBS_S bit will be captured by the PRBS_IS bit. When the PRBS_IS bit is `1', an interrupt will be generated if the PRBS_IM bit (INTM0, 11H...) is set to `1'. The received PRBS/QRSS logic errors can be counted in a 16-bit counter if the ERR_SEL [1:0] bits (MAINT6, 10H...) are set to `00'. Refer to Refer to 3.8 ERROR DETECTION/COUNTING AND INSERTION for the operation of the error counter.
3.7
LOOPBACK
To facilitate testing and diagnosis, the IDT82V2088 provides four different loopback configurations: Analog Loopback, Digital Loopback, Remote Loopback and Inband Loopback. 3.7.1 ANALOG LOOPBACK When the ALP bit (MAINT1, 0BH...) is set to `1', the corresponding channel is configured in Analog Loopback mode. In this mode, the transmit signals are looped back to the Receiver Internal Termination in the receive path then output from RCLKn, RDn, RDPn/RDNn. At the same time, the transmit signals are still output to TTIPn/TRINGn in transmit direction. Figure-15 shows the process. 3.7.2 DIGITAL LOOPBACK When the DLP bit (MAINT1, 0BH...) is set to `1', the corresponding channel is configured in Digital Loopback mode. In this mode, the transmit signals are looped back to the jitter attenuator (if enabled) and decoder in receive path, then output from RCLKn, RDn, RDPn/RDNn. At the same time, the transmit signals are still output to TTIPn/TRINGn in transmit direction. Figure-16 shows the process. Both Analog Loopback mode and Digital Loopback mode allow the sending of the internal patterns (All Ones, All Zeros, PRBS, etc.) which will overwrite the transmit signals. In this case, either TCLKn or MCLK can be used as the reference clock for internal patterns transmission. 3.7.3 REMOTE LOOPBACK When the RLP bit (MAINT1, 0BH...) is set to `1', the corresponding channel is configured in Remote Loopback mode. In this mode, the recovered clock and data output from Clock and Data Recovery on the receive path is looped back to the jitter attenuator (if enabled) and Waveform Shaper in transmit path. Figure-17 shows the process.
Table-20 Criteria for Setting/Clearing the PRBS_S Bit
PRBS/QRSS 6 or less than 6 bit errors detected in a 64 bits hopping window.
Detection
PRBS/QRSS More than 6 bit errors detected in a 64 bits hopping window.
Missing
28
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
One of the Eight Identical Channels
LOSn LOS/AIS Detector B8ZS/ HDB3/AMI Decoder Clock and Data Recovery Receiver Internal Termination RTIPn RRINGn
RCLKn RDn/RDPn CVn/RDNn
Jitter Attenuator
Data Slicer
Adaptive Equalizer
Analog Loopback
TCLKn TDn/TDPn TDNn B8ZS/ HDB3/AMI Encoder Jitter Attenuator Waveform Shaper/LBO Line Driver Transmitter Internal Termination TTIPn TRINGn
Figure-15 Analog Loopback
One of the Eight Identical Channels
LOSn LOS/AIS Detector B8ZS/ HDB3/AMI Decoder Clock and Data Recovery Receiver Internal Termination RTIPn RRINGn
RCLKn RDn/RDPn CVn/RDNn
Jitter Attenuator
Data Slicer
Adaptive Equalizer
Digital Loopback
TCLKn TDn/TDPn TDNn B8ZS/ HDB3/AMI Encoder Jitter Attenuator Waveform Shaper/LBO Line Driver Transmitter Internal Termination TTIPn TRINGn
Figure-16 Digital Loopback
One of the Eight Identical Channels
LOSn LOS/AIS Detector B8ZS/ HDB3/AMI Decoder Clock and Data Recovery Receiver Internal Termination RTIPn RRINGn
RCLKn RDn/RDPn CVn/RDNn
Jitter Attenuator
Data Slicer
Adaptive Equalizer
Remote Loopback
TCLKn TDn/TDPn TDNn B8ZS/ HDB3/AMI Encoder Jitter Attenuator Waveform Shaper/LBO Line Driver Transmitter Internal Termination TTIPn TRINGn
Figure-17 Remote Loopback
29
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.7.4
INBAND LOOPBACK
When PATT[1:0] bits (MAINT0, 0AH...) are set to `11', the corresponding channel is configured in Inband Loopback mode. In this mode, an unframed activate/Deactivate Loopback Code is generated repeatedly in transmit direction per ANSI T1. 403 which overwrite the transmit signals. In receive direction, the framed or unframed code is detected per ANSI T1. 403, even in the presence of 10-2 bit error rate. If the Automatic Remote Loopback is enabled by setting ARLP bit (MAINT1, 0BH...) to `1', the chip will establish/demolish the Remote Loopback based on the reception of the Activate Loopback Code/Deactivate Loopback Code for 5.1 s. If the ARLP bit (MAINT1, 0BH...) is set to `0', the Remote Loopback can also be demolished forcedly. 3.7.4.1 Transmit Activate/Deactivate Loopback Code The pattern of the transmit Activate/Deactivate Loopback Code is defined by the TIBLB[7:0] bits (MAINT3, 0DH...). Whether the code represents an Activate Loopback Code or a Deactivate Loopback Code is judged by the far end receiver. The length of the pattern ranges from 5 bits to 8 bits, as selected by the TIBLB_L[1:0] bits (MAINT2, 0CH...). The pattern can be programmed to 6-bit-long or 8-bit-long respectively by repeating itself if it is 3-bit-long or 4-bit-long. When the PATT[1:0] bits (MAINT0, 0AH...) are set to `11', the transmission of the Activate/Deactivate Loopback Code is initiated. If the PATT_CLK bit (MAINT0, 0AH...) is set to `0' and the PATT[1:0] bits (MAINT0, 0AH...) are set to `00', the transmission of the Activate/Deactivate Loopback Code will stop. The local transmit activate/deactivate code setting should be the same as the receive code setting in the remote end. It is the same thing for the other way round. 3.7.4.2 Receive Activate/Deactivate Loopback Code The pattern of the receive Activate Loopback Code is defined by the RIBLBA[7:0] bits (MAINT4, 0EH...). The length of this pattern ranges from 5 bits to 8 bits, as selected by the RIBLBA_L [1:0] bits (MAINT2, 0CH...). The pattern can be programmed to 6-bit-long or 8-bit-long respectively by repeating itself if it is 3-bit-long or 4-bit-long. The pattern of the receive Deactivate Loopback Code is defined by the RIBLBD[7:0] bits (MAINT5, 0FH...). The length of the receive Deactivate Loopback Code ranges from 5 bits to 8 bits, as selected by the RIBLBD_L[1:0] bits (MAINT2, 0CH...). The pattern can be programmed to
6-bit-long or 8-bit-long respectively by repeating itself if it is 3-bit-long or 4bit-long. After the Activate Loopback Code has been detected in the receive data for more than 30 ms (in E1 mode) / 40 ms (in T1/J1 mode), the IBLBA_S bit (STAT0, 14H...) will be set to `1' to declare the reception of the Activate Loopback Code. After the Deactivate Loopback Code has been detected in the receive data for more than 30 ms (In E1 mode) / 40 ms (In T1/J1 mode), the IBLBD_S bit (STAT0, 14H...) will be set to `1' to declare the reception of the Deactivate Loopback Code. When the IBLBA_IES bit (INTES, 13H...) is set to `0', only the `0' to `1' transition of the IBLBA_S bit will generate an interrupt and set the IBLBA_IS bit (INTS0, 16H...) to `1'. When the IBLBA_IES bit is set to `1', any changes of the IBLBA_S bit will generate an interrupt and set the IBLBA_IS bit (INTS0, 16H...) to `1'. The IBLBA_IS bit will be reset to `0' after being read. When the IBLBD_IES bit (INTES, 13H...) is set to `0', only the `0' to `1' transition of the IBLBD_S bit will generate an interrupt and set the IBLBD_IS bit (INTS0, 16H...) to `1'. When the IBLBD_IES bit is set to `1', any changes of the IBLBD_S bit will generate an interrupt and set the IBLBD_IS bit (INTS0, 16H...) to `1'. The IBLBD_IS bit will be reset to `0' after being read. 3.7.4.3 Automatic Remote Loopback When ARLP bit (MAINT1, 0BH...) is set to `1', the corresponding channel is configured into the Automatic Remote Loopback mode. In this mode, if the Activate Loopback Code has been detected in the receive data for more than 5.1 s, the Remote Loopback (shown as Figure-17) will be established automatically, and the RLP_S bit (STAT1, 15H...) will be set to `1' to indicate the establishment of the Remote Loopback. The IBLBA_S bit (STAT0, 14H...) is set to `1' to generate an interrupt. In this case, the Remote Loopback mode will still be kept even if the receiver stop receiving the Activate Loopback Code. If the Deactivate Loopback Code has been detected in the receive data for more than 5.1 s, the Remote Loopback will be demolished automatically, and the RLP_S bit (STAT1, 15H...) will set to `0' to indicate the demolishment of the Remote Loopback. The IBLBD_S bit (STAT0, 14H...) is set to `1' to generate an interrupt. The Remote Loopback can also be demolished forcedly by setting ARLP bit (MAINT1, 0BH...) to `0'.
30
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.8
3.8.1
ERROR DETECTION/COUNTING AND INSERTION
DEFINITION OF LINE CODING ERROR
*
The following line encoding errors can be detected and counted by the IDT82V2088: * Received Bipolar Violation (BPV) Error: In AMI coding, when two consecutive pulses of the same polarity are received, a BPV error is declared.
*
HDB3/B8ZS Code Violation (CV) Error: In HDB3/B8ZS coding, a CV error is declared when two consecutive BPV errors are detected, and the pulses that have the same polarity as the previous pulse are not the HDB3/B8ZS zero substitution pulses. Excess Zero (EXZ) Error: there are two standards defining the EXZ errors: ANSI and FCC. The EXZ_DEF bit (MAINT6, 10H...) chooses which standard will be adopted by the corresponding channel to judge the EXZ error. Table-21 shows definition of EXZ.
Table-21 EXZ Definition
EXZ Definition ANSI AMI HDB3 B8ZS More than 15 consecutive 0s are detected More than 3 consecutive 0s are detected More than 7 consecutive 0s are detected FCC More than 80 consecutive 0s are detected More than 3 consecutive 0s are detected More than 7 consecutive 0s are detected
3.8.2
ERROR DETECTION AND COUNTING
Which type of the receiving errors (Received CV/BPV errors, excess zero errors and PRBS logic errors) will be counted is determined by ERR_SEL[1:0] bits (MAINT6, 10H...). Only one type of receiving error can be counted at a time except that when the ERR_SEL[1:0] bits are set to `11', both CV/BPV and EXZ errors will be detected and counted. The receiving errors are counted in an internal 16-bit Error Counter. Once an error is detected, an error interrupt which is indicated by corresponding bit in (INTS1, 17H...) will be generated if it is not masked. This Error Counter can be operated in two modes: Auto Report Mode and Manual Report Mode, as selected by the CNT_MD bit (MAINT6, 10H...). In Single Rail mode, once BPV or CV errors are detected, the CVn pin will be driven to high for one RCLK period. * Auto Report Mode In Auto Report Mode, the internal counter starts to count the received errors when the CNT_MD bit (MAINT6, 10H...) is set to `1'. A one-second timer is used to set the counting period. The received errors are counted within one second. If the one-second timer expires, the value in the internal counter will be transferred to (CNT0, 18H...) and (CNT1, 19H...), then the internal counter will be reset and start to count received errors for the next second. The errors occurred during the transfer will be accumulated to the next round. The expiration of the one-second timer will set TMOV_IS bit (INTS1, 17H...) to `1', and will generate an interrupt if the TIMER_IM bit (INTM1, 12H...) is set to `0'. The TMOV_IS bit (INTS1, 17H...) will be cleared after the interrupt register is read. The content in the (CNT0, 18H...) and
(CNT1, 19H...) should be read within the next second. If the counter overflows, a counter overflow interrupt which is indicated by CNT_OV_IS bit (INTS1, 17H...) will be generated if it is not masked by CNT_IM bit (INTM1, 12H...).
Auto Report Mode (CNT_MD=1)
counting N One-Second Timer expired? Y data in counter next second repeats the same process
CNT0, CNT1 counter 0
Bit TMOV_IS is set to '1'
read the data in CNT0, CNT1 within the next second Bit TMOV_IS is cleared after the interrupt register is read
Figure-18 Auto Report Mode
31
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
* Manual Report Mode In Manual Report Mode, the internal Error Counter starts to count the received errors when the CNT_MD bit (MAINT6, 10H...) is set to `0'. When there is a `0' to `1' transition on the CNT_TRF bit (MAINT6, 10H...), the data in the counter will be transferred to (CNT0, 18H...) and (CNT1, 19H...), then the counter will be reset. The errors occurred during the transfer will be accumulated to the next round. If the counter overflows, a counter overflow interrupt indicated by CNT_OV_IS bit (INTS1, 17H...) will be generated if it is not masked by CNT_IM bit (INTM1, 12H...).
Manual Report mode (CNT_MD=0)
3.8.3
BIPOLAR VIOLATION AND PRBS ERROR INSERTION
Only when three consecutive `1's are detected in the transmit data stream, will a `0' to `1' transition on the BPV_INS bit (MAINT6, 10H...) generate a bipolar violation pulse, and the polarity of the second `1' in the series will be inverted. A `0' to `1' transition on the EER_INS bit (MAINT6, 10H...) will generate a logic error during the PRBS/QRSS transmission.
3.9
LINE DRIVER FAILURE MONITORING
counting N A '0' to '1' transition on CNT_TRF? Y CNT0, CNT1 counter counter 0 data in next round repeat the same process
The transmit driver failure monitor can be enabled or disabled by setting DFM_OFF bit (TCF1, 03H...). If the transmit driver failure monitor is enabled, the transmit driver failure will be captured by DF_S bit (STAT0, 14H...). The transition of the DF_S bit is reflected by DF_IS bit (INTS0, 16H...), and, if enabled by DF_IM bit (INTM0, 11H...), will generate an interrupt. When there is a short circuit on the TTIPn/TRINGn port, the output current will be limited to 100 mAPP typically and an interrupt will be generated.
Read the data in CNT0, CNT1 within next round1 Reset CNT_TRF for the next '0' to '1' transition
Figure-19 Manual Report Mode
Note: 1. It is recommended that users should do the followings within next round of error counting: Read the data in CNT0 and CNT1; Reset CNT_TRF bit for the next `0' to `1' transition on this bit.
32
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.10 MCLK AND TCLK
3.10.1 MASTER CLOCK (MCLK) MCLK is an independent, free-running reference clock. MCLK is 1.544 MHz or 37.056 MHz for T1/J1 applications and 2.048 MHz or 49.152 MHz in E1 mode. This reference clock is used to generate several internal reference signals: * Timing reference for the integrated clock recovery unit. * Timing reference for the integrated digital jitter attenuator. * Timing reference for microcontroller interface. * Generation of RCLK signal during a loss of signal condition if AIS is enabled. * Reference clock during a blue alarm Transmit All Ones (TAOS), all zeros, PRBS/QRSS and inband loopback patterns if it is selected as the reference clock. For ATAO and AIS, MCLK is always used as the reference clock. Figure-20 shows the chip operation status in different conditions of MCLK and TCLKn. The missing of MCLK will set all the eight TTIP/TRING to high impedance state.
3.10.2 TRANSMIT CLOCK (TCLK) The TCLKn is used to sample the transmit data on TDn/TDPn, TDNn. The active edge of TCLKn can be selected by the TCLK_SEL bit (TCF0, 02H...). During Transmit All Ones, PRBS/QRSS patterns or Inband Loopback Code, either TCLKn or MCLK can be used as the reference clock. This is selected by the PATT_CLK bit (MAINT0, 0AH...). But for Automatic Transmit All Ones and AIS, only MCLK is used as the reference clock and the PATT_CLK bit is ignored. In Automatic Transmit All Ones condition, the ATAO bit (MAINT0, 0AH) is set to `1'. In AIS condition, the AISE bit (MAINT0, 0AH) is set to `1'. If TCLKn has been missing for more than 70 MCLK cycles, TCLK_LOS bit (STAT0, 14H...) will be set, and the corresponding TTIPn/TRINGn will become high impedance if this channel is not used for remote loopback or is not using MCLK to transmit internal patterns (TAOS, All Zeros, PRBS and in-band loopback code). When TCLKn is detected again, TCLK_LOS bit (STAT0, 14H...) will be cleared. The reference frequency to detect a TCLKn loss is derived from MCLK.
clocked
MCLK=H/L? yes
clocked
TCLKn status?
L/H
normal operation mode
transmitter n enters high impedance status and generates transmit clock loss interrupt if not masked
all transmitters high impedance status
Figure-20 TCLK Operation Flowchart
33
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.11 MICROCONTROLLER INTERFACES
The microcontroller interface provides access to read and write the registers in the device. The chip supports serial processor interface and two kinds of parallel processor interface: Motorola non_multiplexed mode and Intel non_multiplexed mode. By pulling pin P/S to low or to High, the microcontroller interface can be set to work in serial mode or in parallel mode respectively. Refer to 7 MICROCONTROLLER INTERFACE TIMING CHARACTERISTICS for details. 3.11.1 PARALLEL MICROCONTROLLER INTERFACE The interface is compatible with Motorola or Intel microcontroller. Pin INT/MOT is used to select the operating mode of the parallel microcontroller
interface. When pin INT/MOT is pulled to Low, the parallel microcontroller interface is configured for Motorola compatible hosts. When High, it is for Intel compatible microcontrollers. 3.11.2 SERIAL MICROCONTROLLER INTERFACE The serial interface pins include SCLK, SDI, SDO, CS as well as SCLKE (control pin for the selection of serial clock active edge). By pulling P/S pin to LOW, the device operates in the serial host Mode. In this mode, the registers are programmed through a 24-bit word which contains an 8-bit address byte (A0~A7), a subsequent 8-bit command byte (bit R/W) and an 8-bit data byte (D0~D7). When bit R/W is `1', data is read out from pin SDO. When bit R/W is `0', data is written into SDI pin. Refer to Figure-21.
CS SCLK SDI A0 A1 A2 A3 A4 A5 A6 A7 R/W D o n ' t C a r e D0 D1 D2 D3 D4 D5 D6 D7
address byte
SDO
command byte
D0
input data byte (R/W=0)
D1 D2 D3 D4 D5 D6 D7
remains high impedance
Output data byte (R/W=1)
Figure-21 Serial Processor Interface Function Timing
34
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.12 INTERRUPT HANDLING
All kinds of interrupt of the IDT82V2088 are indicated by the INT pin. When the INT_PIN[0] bit (GCF0, 40H) is `0', the INT pin is open drain active low, with a 10 K external pull-up resistor. When the INT_PIN[1:0] bits (GCF0, 40H) are `01', the INT pin is push-pull active low; when the INT_PIN[1:0] bits are `10', the INT pin is push-pull active high. All the interrupt can be disabled by the INTM_GLB bit (GCF0, 40H). When the INTM_GLB bit (GCF0, 40H) is set to `0', an active level on the INT pin represents an interrupt of the IDT82V2088. The INT_CH[7:0] bits (INTCH, 80H) should be read to identify which channel(s) generate the interrupt. The interrupt event is captured by the corresponding bit in the Interrupt Status Register (INTS0, 16H...) or (INTS1, 17H...). Every kind of interrupt can be enabled/disabled individually by the corresponding bit in the register (INTM0, 11H...) or (INTM1, 12H...). Some event is reflected by the corresponding bit in the Status Register (STAT0, 14H...) or (STAT1, 15H...), and the Interrupt Trigger Edge Selection Register can be used to determine how the Status Register sets the Interrupt Status Register. After the Interrupt Status Register (INTS0, 16H...) or (INTS1, 17H...) is read, the corresponding bit indicating which channel generates the interrupt in the INTCH register (80H) will be reset. Only when all the pending
interrupt is acknowledged through reading the Interrupt Status Registers of all the channels (INTS0, 16H...) or (INTS1, 17H...) will all the bits in the INTCH register (80H) be reset and the INT pin become inactive. There are totally fourteen kinds of events that could be the interrupt source for one channel: (1).LOS Detected (2).AIS Detected (3).Driver Failure Detected (4).TCLK Loss (5).Synchronization Status of PRBS (6).PRBS Error Detected (7).Code Violation Received (8).Excessive Zeros Received (9).JA FIFO Overflow/Underflow (10).Inband Loopback Code Status (11).Equalizer Out of Range (12).One-Second Timer Expired (13).Error Counter Overflow (14).Arbitrary Waveform Generator Overflow Table-22 is a summary of all kinds of interrupt and their associated Status bit, Interrupt Status bit, Interrupt Trigger Edge Selection bit and Interrupt Mask bit.
Table-22 Interrupt Event
Interrupt Event LOS Detected AIS Detected Driver Failure Detected TCLKn Loss Synchronization Status of PRBS/QRSS PRBS/QRSS Error Code Violation Received Excessive Zeros Received JA FIFO Overflow JA FIFO Underflow Equalizer Out of Range Inband Loopback Activate Code Status Inband Loopback Deactivate Code Status One-Second Timer Expired Error Counter Overflow Arbitrary Waveform Generator Overflow EQ_S IBLBA_S IBLBD_S Status bit (STAT0, STAT1) LOS_S AIS_S DF_S TCLK_LOS PRBS_S Interrupt Status bit (INTS0, INTS1) LOS_IS AIS_IS DF_IS TCLK_LOS_IS PRBS_IS ERR_IS CV_IS EXZ_IS JAOV_IS JAUD_IS EQ_IS IBLBA_IS IBLBD_IS TMOV_IS CNT_OV_IS DAC_OV_IS EQ_IES IBLBA_IES IBLBD_IES Interrupt Edge Selection bit (INTES) LOS_IES AIS_IES DF_IES TCLK_IES PRBS_IES Interrupt Mask bit (INTM0, INTM1) LOS_IM AIS_IM DF_IM TCLK_IM PRBS_IM ERR_IM CV_IM EXZ_IM JAOV_IM JAUD_IM EQ_IM IBLBA_IM IBLBD_IM TIMER_IM CNT_IM DAC_OV_IM
35
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
3.13 GENERAL PURPOSE I/O
The IDT82V2088 provides two general purpose digital I/O pins: GPIO1, GPIO0. These two pins can be considered as digital Input or Output port by the DIR1 bit (GPIO, A0H) and DIR0 bit (GPIO, A0H) respectively. If the GPIO1 and GPIO0 are configured as Input port, the LEVEL1 bit (GPIO, A0H) and the LEVEL0 bit (GPIO, A0H) are used to reflect the level of the GPIO1 pin and the GPIO0 pin respectively. If the GPIO1 and GPIO0 are configured as Output port, the content in the LEVEL1 bit and LEVEL0 bit determines the logic value of GPIO1 pin and GPIO0 pin respectively.
3.15 RESET OPERATION
The chip can be reset in two ways: Software Reset: Writing to the RST register (20H) will reset the chip in 1 us. * Hardware Reset: Asserting the RST pin low for a minimum of 100 ns will reset the chip. * After reset, all drivers output are in high impedance state, all the internal flip-flops are reset, and all the registers are initialized to default values.
3.14 5V TOLERANT I/O PINS
All digital input pins will tolerate 5.0 5% volts and are compatible with TTL logic.
3.16 POWER SUPPLY
This chip uses a single 3.3 V power supply.
36
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
4
4.1
PROGRAMMING INFORMATION
REGISTER LIST AND MAP
Registers. If the configuration of all the eight channels is the same, the COPY bit (GCF0, 40H) can be set to `1' to establish the Broadcasting mode. In the Broadcasting mode, the Writing operation on any of the eight channels' registers will be copied to the corresponding registers of all the other channels.
The IDT82V2088 registers can be divided into Global Registers and Local Registers. The operation on the Global Registers affects all the eight channels while the operation on Local Registers only affects that specific channel. For different channel, the address of Local Register is different. Table-23 is the map of Global Registers and Table-24 is the map of Local
Table-23 Global Register List and Map
Address (Hex) 00 20 40 60 80 A0 C0 E0 Register ID RST GCF0 GCF1 INTCH GPIO Reserved Reserved R W R/W R/W R R/W MON3 INT_CH7 MON2 INT_CH6 MON1 INT_CH5 T1E1 MON0 INT_CH4 COPY INT_CH3 LEVEL1 INTM_GLB INT_CH2 LEVEL0 INT_PIN1 INT_CH1 DIR1 INT_PIN0 INT_CH0 DIR0 R/W b7 ID7 b6 ID6 b5 ID5 b4 ID4 Map b3 ID3 b2 ID2 b1 ID1 b0 ID0
37
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-24 Per Channel Register List and Map
Address (Hex) CH1-CH8 Jitter Attenuation Control Register 01,21,41,61,81,A1,C1,E1 02,22,42,62,82,A2,C2,E2 03,23,43,63,83,A3,C3,E3 04,24,44,64,84,A4,C4,E4 05,25,45,65,85,A5,C5,E5 06,26,46,66,86,A6,C6,E6 07,27,47,67,87,A7,C7,E7 08,28,48,68,88,A8,C8,E8 09,29,49,69,89,A9,C9,E9 JACF TCF0 TCF1 TCF2 TCF3 TCF4 RCF0 RCF1 RCF2 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R R R R R R R/W DONE TIBLB7 RIBLBA7 RIBLBD7 EQ_IM EQ_IES EQ_S EQ_IS DAC_OV_IS Bit7 Bit15 RW WDAT6 EQ_ON PATT1 TIBLB6 RIBLBA6 RIBLBD6 BPV_INS IBLBA_IM JAOV_IM IBLBA_IES IBLBA_S IBLBA_IS JAOV_IS Bit6 Bit14 JA_LIMIT DFM_OFF SCAL5 UI1 WDAT5 SLICE1 PATT0 TIBLB_L1 TIBLB5 RIBLBA5 RIBLBD5 ERR_INS IBLBD_IM JAUD_IM IBLBD_IES IBLBD_S RLP_S IBLBD_IS JAUD_IS Bit5 Bit13 T_TERM2 JACF1 T_OFF THZ SCAL4 UI0 WDAT4 R_OFF LOS4 SLICE0 PATT_CLK TIBLB_L0 TIBLB4 RIBLBA4 RIBLBD4 EXZ_DEF PRBS_IM ERR_IM PRBS_IES PRBS_S LATT4 PRBS_IS ERR_IS Bit4 Bit12 T_TERM1 JACF0 TD_INV PULS3 SCAL3 SAMP3 WDAT3 RD_INV LOS3 UPDW1 PRBS_INV ARLP RIBLBA_L1 TIBLB3 RIBLBA3 RIBLBD3 ERR_SEL1 TCLK_IM EXZ_IM TCLK_IES TCLK_LOS LATT3 TCLK_LOS_IS EXZ_IS Bit3 Bit11 T_TERM0 JADP1 TCLK_SEL PULS2 SCAL2 SAMP2 WDAT2 RCLK_SEL LOS2 UPDW0 LAC RLP TIBLB2 RIBLBA2 RIBLBD2 ERR_SEL0 DF_IM CV_IM DF_IES DF_S LATT2 DF_IS CV_IS Bit2 Bit10 R_TERM2 JADP0 T_MD1 PULS1 SCAL1 SAMP1 WDAT1 R_MD1 LOS1 MG1 AISE ALP TIBLB1 RIBLBA1 RIBLBD1 CNT_MD AIS_IM TIMER_IM AIS_IES AIS_S LATT1 AIS_IS TMOV_IS Bit1 Bit9 R_TERM1 JABW T_MD0 PULS0 SCAL0 SAMP0 WDAT0 R_MD0 LOS0 MG0 ATAO DLP TIBLB0 RIBLBA0 RIBLBD0 CNT_TRF LOS_IM CNT_IM LOS_IES LOS_S LATT0 LOS_IS CNT_OV_IS Bit0 Bit8 R_TERM0 Transmit Path Control Registers Register R/W b7 b6 b5 b4 Map b3 b2 b1 b0
Receive Path Control Registers
Network Diagnostics Control Registers 0A,2A,4A,6A,8A,AA,CA,EA MAINT0 0B,2B,4B,6B,8B,AB,CB,EB MAINT1 0C,2C,4C,6C,8C,AC,CC,EC MAINT2 0D,2D,4D,6D,8D,AD,CD,ED MAINT3 0E,2E,4E,6E,8E,AE,CE,EE MAINT4 0F,2F,4F,6F,8F,AF,CF,EF 10,30,50,70,90,B0,D0,F0 Interrupt Control Registers 11,31,51,71,91,B1,D1,F1 12,32,52,72,92,B2,D2,F2 13,33,53,73,93,B3,D3,F3 Line Status Registers 14,34,54,74,94,B4,D4,F4 15,35,55,75,95,B5,D5,F5 Interrupt Status Registers 16,36,56,76,96,B6,D6,F6 17,37,57,77,97,B7,D7,F7 Counter Registers 18,38,58,78,98,B8,D8,F8 19,39,59,79,99,B9,D9,F9 CNT0 CNT1 INTS0 INTS1 STAT0 STAT1 INTM0 INTM1 INTES R/W DAC_OV_IM MAINT5 MAINT6
RIBLBA_L0 RIBLBD_L1 RIBLBD_L0
Transmit and Receive Termination Registers 1A,3A,5A,7A,9A,BA,DA,FA TERM
38
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
4.2
4.2.1
REGISTER DESCRIPTION
GLOBAL REGISTERS
Table-25 ID: Chip Revision Register
(R, Address = 00H)
Symbol ID[7:0] Bit 7-0 Default 01H 00H is for the first version. Description
Table-26 RST: Reset Register
(W, Address = 20H)
Symbol RST[7:0] Bit 7-0 Default 01H Description Software reset. A write operation on this register will reset all internal registers to their default values, and the status of all ports are set to the default status. The content in this register can not be changed.
Table-27 GCF0: Global Configuration Register 0
(R/W, Address = 40H)
Symbol T1E1 Bit 7-6 5 4 Default 0 0 0 Reserved Reserved. For normal operation, this bit should be set to `0'. This bit selects E1 or T1/J1 operation mode globally. = 0: E1 mode is selected. = 1: T1/J1 mode is selected. Enable broadcasting mode. = 0: Broadcasting mode disabled = 1: Broadcasting mode enabled. Writing operation on one channel's register will be copied exactly to the corresponding registers in all the other channels. Global interrupt enable = 0: Interrupt is globally enabled. But for each individual interrupt, it still can be disabled by its corresponding Interrupt mask Bit. = 1: All the interrupts are disabled for all channels. Interrupt pin operation mode selection = x0: open drain, active low (with an external pull-up resistor) = 01: push-pull, active low = 11: push-pull, active high Description
COPY
3
0
INTM_GLB
2
1
INT_PIN[1:0]
1-0
00
39
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-28 GCF1: Global Configuration Register 1
(R/W, Address = 60H)
Symbol MON[3:0] Bit 7-4 Default 0000 Description MON selects the transmitter or receiver channel to be monitored. = 0000: receiver 1 is in normal operation without monitoring = 0001: monitor receiver 2 = 0010: monitor receiver 3 = 0011: monitor receiver 4 = 0100: monitor receiver 5 = 0101: monitor receiver 6 = 0110: monitor receiver 7 = 0111: monitor receiver 8 = 1000: transmitter 1 is in normal operation without monitoring = 1001: monitor transmitter 2 = 1010: monitor transmitter 3 = 1011: monitor transmitter 4 = 1100: monitor transmitter 5 = 1101: monitor transmitter 6 = 1110: monitor transmitter 7 = 1111: monitor transmitter 8 Reserved
-
3-0
0000
Table-29 INTCH: Interrupt Channel Indication Register
(R, Address = 80H)
Symbol INT_CH[7:0] Bit 7-0 Default 00H Description INT_CH[n]=1 indicates that an interrupt was generated by channel [n+1] respectively.
Table-30 GPIO: General Purpose IO Pin Definition Register
(R/W, Address = A0H)
Symbol LEVEL1 Bit 7-4 3 Default 0000 Reserved. When GPIO1 is defined as an output port, this bit determines the output level on GPIO1 pin. = 0: low level output on port GPIO1 = 1: high level output on port GPIO1 When GPIO1 is defined as an input port, this bit reflects the input level of GPIO1 pin. = 0: low level input on port GPIO1 = 1: high level input on port GPIO1 When GPIO0 is defined as an output port, this bit determines the output level on GPIO0 pin. = 0: low level output on port GPIO0 = 1: high level output on port GPIO0 When GPIO0 is defined as an input port, this bit reflects the input level on GPIO0 pin = 0: low level input on port GPIO0 = 1: high level input on port GPIO0 = 0: port GPIO1 is configured as output port = 1: port GPIO1 is configured as input port = 0: port GPIO0 is configured as output port = 1: port GPIO0 is configured as input port Description
LEVEL0
2
-
DIR1 DIR0
1 0
1 1
40
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
4.2.2
JITTER ATTENUATION CONTROL REGISTER
Table-31 JACF: Jitter Attenuator Configuration Register
(R/W, Address = 01H,21H,41H,61H,81H,A1H,C1H,E1H)
Symbol JA_LIMIT Bit 7-6 5 Default 00 0 Reserved Wide Jitter Attenuation bandwidth = 0: normal mode = 1: JA limit mode Jitter Attenuator configuration = 00/10: JA not used = 01: JA in transmit path = 11: JA in receive path Jitter Attenuator depth selection = 00: 128 bits = 01: 64 bits = 10/11: 32 bits Jitter transfer function bandwidth selection JABW 0 1 T1/J1 5 Hz 1.25 Hz E1 6.8 Hz 0.9 Hz Description
JACF[1:0]
4-3
00
JADP[1:0]
2-1
00
JABW
0
0
4.2.3
TRANSMIT PATH CONTROL REGISTERS
Table-32 TCF0: Transmitter Configuration Register 0
(R/W, Address = 02H,22H,42H,62H,82H,A2H,C2H,E2H)
Symbol T_OFF Bit 7-5 4 Default 000 0 Reserved Transmitter power down enable = 0: Transmitter power up = 1: Transmitter power down and line driver high impedance Transmit data invert = 0: data on TDn or TDPn/TDNn is active high = 1: data on TDn or TDPn/TDNn is active low Transmit clock edge select = 0: data on TDn or TDPn/TDNn is sampled on the falling edges of TCLKn = 1: data on TDn or TDPn/TDNn is sampled on the rising edges of TCLKn Transmitter operation mode control bits which select different stages of transmit data path = 00: enable HDB3/B8ZS encoder and waveform shaper blocks, input on TDn is single rail NRZ data = 01: enable AMI encoder and waveform shaper blocks, input on pin TDn is single rail NRZ data = 1x: encoder is bypassed, dual rail NRZ transmit data input on pin TDPn/TDNn Description
TD_INV
3
0
TCLK_SEL
2
0
T_MD[1:0]
1-0
00
41
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-33 TCF1: Transmitter Configuration Register 1
(R/W, Address = 03H,23H,43H,63H,83H,A3H,C3H,E3H)
Symbol DFM_OFF Bit 7-6 5 Default 00 0 Transmit driver failure monitor disable = 0: DFM is enabled = 1: DFM is disabled Transmit line driver tri-state enable = 0: normal state = 1: transmit line driver tri-state (other transmit path still in normal state) These bits select the transmit template/LBO for short-haul/long-haul applications. T1/E1/J1 00001 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 11xx E1 E1 DSX1 DSX1 DSX1 DSX1 DSX1 J1 DS1 DS1 DS1 DS1 TCLK 2.048 MHz 2.048 MHz 1.544 MHz 1.544 MHz 1.544 MHz 1.544 MHz 1.544 MHz 1.544 MHz 1.544 MHz 1.544 MHz 1.544 MHz 1.544 MHz Cable Impedance 75 120 100 100 100 100 100 110 100 100 100 100 Cable Range or LBO 0~133 ft 133~266 ft 266~399 ft 399~533 ft 533~655 ft 0~655 ft 0 dB LBO -7.5 dB LBO -15 dB LBO -22.5 dB LBO Cable Loss 0~43 dB (default) 0~43 dB 0~0.6 dB 0.6~1.2 dB 1.2~1.8 dB 1.8~2.4 dB 2.4~3.0 dB 0~3.0 dB 0~36 dB 0~28.5 dB 0~21 dB 0~13.5 dB Description Reserved. This bit should be `0' for normal operation.
THZ
4
1
PULS[3:0]
3-0
0000
User programmable waveform setting
1. In internal impedance matching mode, for E1/75 cable impedance, the PULS[3:0] bits (TCF1, 03H...) should be set to `0000'. In external impedance matching mode, for E1/75 cable impedance, the PULS[3:0] bits should be set to `0001'.
Table-34 TCF2: Transmitter Configuration Register 2
(R/W, Address = 04H,24H,44H,64H,84H,A4H,C4H,E4H)
Symbol SCAL[5:0] Bit 7-6 5-0 Default 00 100001 Reserved SCAL specifies a scaling factor to be applied to the amplitude of the user-programmable arbitrary pulses which is to be transmitted if needed. The default value of SCAL[5:0] is `100001'. Refer to 3.2.3.3 User-Programmable Arbitrary Waveform. = 110110: default value for T1 0~133 ft, T1 133~266 ft, T1 266~399 ft, T1 399~533 ft, T1 533~655 ft, J1 0~655 ft, DS1 0dB LBO. One step change of this value results in 2% scaling up/down against the pulse amplitude. = 010001: default value for DS1 -7.5 dB LBO. One step change of this value results in 6.25% scaling up/down against the pulse amplitude. = 001000: default value for DS1 -15.0 dB LBO. One step change of this value results in 12.5% scaling up/down against the pulse amplitude. = 000100: default value for DS1 -22.5 dB LBO. One step change of this value results in 25% scaling up/down against the pulse amplitude. = 100001: default value for E1 75 and 120 . One step change of this value results in 3% scaling up/down against the pulse amplitude. Description
42
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-35 TCF3: Transmitter Configuration Register 3
(R/W, Address = 05H,25H,45H,65H,85H,A5H,C5H,E5H)
Symbol DONE RW Bit 7 6 Default 0 0 This bit selects read or write operation = 0: write to RAM = 1: read from RAM These bits specify the unit interval address. There are 4 unit intervals. = 00: UI address is 0 (The most left UI) = 01: UI address is 1 = 10: UI address is 2 = 11: UI address is 3 These bits specify the sample address. Each UI has 16 samples. = 0000: sample address is 0 (The most left Sample) = 0001: sample address is 1 = 0010: sample address is 2 ...... = 1110: sample address is 14 = 1111: sample address is 15 Description After `1' is written to this bit, a read or write operation is implemented.
UI[1:0]
5-4
00
SAMP[3:0]
3-0
0000
Table-36 TCF4: Transmitter Configuration Register 4
(R/W, Address = 06H,26H,46H,66H,86H,A6H,C6H,E6H)
Symbol WDAT[6:0] Bit 7 6-0 Default 0 0000000 Reserved In Indirect Write operation, the WDAT[6:0] will be loaded to the pulse template RAM, specifying the amplitude of the Sample. After an Indirect Read operation, the amplitude data of the Sample in the pulse template RAM will be output to the WDAT[6:0]. Description
4.2.4
RECEIVE PATH CONTROL REGISTERS
Table-37 RCF0: Receiver Configuration Register 0
(R/W, Address = 07H,27H,47H,67H,87H,A7H,C7H,E7H)
Symbol R_OFF Bit 7-5 4 Default 000 0 Reserved Receiver power down enable = 0: Receiver power up = 1: Receiver power down Receive data invert = 0: data on RDn or RDPn/RDNn is active high = 1: data on RDn or RDPn/RDNn is active low Receive clock edge select (this bit is ignored in slicer mode) = 0: data on RDn or RDPn/RDNn is updated on the rising edges of RCLKn = 1: data on RDn or RDPn/RDNn is updated on the falling edges of RCLKn Receiver path decoding selection = 00: receive data is HDB3 (E1) / B8ZS (T1/J1) decoded and output on RDn with single rail NRZ format = 01: receive data is AMI decoded and output on RDn with single rail NRZ format = 10: decoder is bypassed, re-timed dual rail data with NRZ format output on RDPn/RDNn (dual rail mode with clock recovery) = 11: both CDR and decoder blocks are bypassed, slicer data with RZ format output on RDPn/RDNn (slicer mode) Description
RD_INV
3
0
RCLK_SEL
2
0
R_MD[1:0]
1-0
00
43
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-38 RCF1: Receiver Configuration Register 1
(R/W, Address = 08H,28H,48H,68H,88H,A8H,C8H,E8H)
Symbol EQ_ON LOS[4:0] Bit 7 6 5 4-0 Default 0 0 0 10101 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 10001 10010 10011 10100 10101 10110-11111 Reserved = 0: receive equalizer off (short haul receiver) = 1: receive equalizer on (long haul receiver) Reserved. Should be 0 for normal operation. LOS Clear Level (dB) 0 >-2 >-4 >-6 >-8 >-10 >-12 >-14 >-16 >-18 >-20 >-22 >-24 >-26 >-28 >-30 >-32 >-34 >-36 >-38 >-40 >-42 >-44 LOS Declare Level (dB) <-4 <-6 <-8 <-10 <-12 <-14 <-16 <-18 <-20 <-22 <-24 <-26 <-28 <-30 <-32 <-34 <-36 <-38 <-40 <-42 <-44 <-46 <-48 Description
44
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-39 RCF2: Receiver Configuration Register 2
(R/W, Address = 09H,29H,49H,69H,89H,A9H,C9H,E9H)
Symbol SLICE[1:0] Bit 7-6 5-4 Default 00 01 Reserved Receive slicer threshold = 00: The receive slicer generates a mark if the voltage on RTIPn/RRINGn exceeds 40% of the peak amplitude. = 01: The receive slicer generates a mark if the voltage on RTIPn/RRINGn exceeds 50% of the peak amplitude. = 10: The receive slicer generates a mark if the voltage on RTIPn/RRINGn exceeds 60% of the peak amplitude. = 11: The receive slicer generates a mark if the voltage on RTIPn/RRINGn exceeds 70% of the peak amplitude. Equalizer observation window = 00: 32 bits = 01: 64 bits = 10: 128 bits = 11: 256 bits Monitor gain setting: these bits select the internal linear gain boost = 00: 0 dB = 01: 22 dB = 10: 26 dB = 11: 32 dB Description
UPDW[1:0]
3-2
10
MG[1:0]
1-0
00
4.2.5
NETWORK DIAGNOSTICS CONTROL REGISTERS
Table-40 MAINT0: Maintenance Function Control Register 0
(R/W, Address = 0AH,2AH,4AH,6AH,8AH,AAH,CAH,EAH)
Symbol PATT[1:0] Bit 7 6-5 Default 0 00 Reserved These bits select the internal pattern and insert it into the transmit data stream. = 00: normal operation (PATT_CLK = 0) / insert all zeros (PATT_CLK = 1) = 01: insert All Ones = 10: insert PRBS (E1: 215-1) or QRSS (T1/J1: 220-1) = 11: insert programmable Inband Loopback activate or deactivate code Selects reference clock for transmitting internal pattern = 0: uses TCLKn as the reference clock = 1: uses MCLK as the reference clock Inverts PRBS = 0: PRBS data is not inverted = 1: PRBS data is inverted before transmission and detection The LOS/AIS criterion is selected as below: = 0: G.775 (E1) / T1.231 (T1/J1) = 1: ETSI 300233 & I.431 (E1) / I.431 (T1/J1) AIS enable during LOS = 0: AIS insertion on RDPn/RDNn/RCLKn is disabled during LOS = 1: AIS insertion on RDPn/RDNn/RCLKn is enabled during LOS Automatically Transmit All Ones (enabled only when PATT[1:0] = 01) = 0: disabled = 1: Automatically Transmit All Ones pattern at TTIPn/TRINGn during LOS. Description
PATT_CLK
4
0
PRBS_INV
3
0
LAC
2
0
AISE
1
0
ATAO
0
0
45
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-41 MAINT1: Maintenance Function Control Register 1
(R/W, Address = 0BH,2BH,4BH,6BH,8BH,ABH,CBH,EBH)
Symbol ARLP Bit 7-4 3 Default 0000 0 Reserved Automatic Remote Loopback Control = 0: disables Automatic Remote Loopback (normal transmit and receive operation) = 1: enables Automatic Remote Loopback Remote loopback enable = 0: disables remote loopback (normal transmit and receive operation) = 1: enables remote loopback Analog loopback enable = 0: disables analog loopback (normal transmit and receive operation) = 1: enables analog loopback Digital loopback enable = 0: disables digital loopback (normal transmit and receive operation) = 1: enables digital loopback Description
RLP
2
0
ALP
1
0
DLP
0
0
Table-42 MAINT2: Maintenance Function Control Register 2
(R/W, Address = 0CH,2CH,4CH,6CH,8CH,ACH,CCH,ECH)
Symbol TIBLB_L[1:0] Bit 7-6 5-4 Default 00 00 Reserved. Defines the length of the user-programmable transmit Inband Loopback activate/deactivate code contained in TIBLB register. The default selection is 5 bits length. = 00: 5-bit activate code in TIBLB [4:0] = 01: 6-bit activate code in TIBLB [5:0] = 10: 7-bit activate code in TIBLB [6:0] = 11: 8-bit activate code in TIBLB [7:0] Defines the length of the user-programmable receive Inband Loopback activate code contained in RIBLBA register. = 00: 5-bit activate code in RIBLBA [4:0] = 01: 6-bit activate code in RIBLBA [5:0] = 10: 7-bit activate code in RIBLBA [6:0] = 11: 8-bit activate code in RIBLBA [7:0] Defines the length of the user-programmable receive Inband Loopback deactivate code contained in RIBLBD register. = 00: 5-bit deactivate code in RIBLBD [4:0] = 01: 6-bit deactivate code in RIBLBD [5:0] = 10: 7-bit deactivate code in RIBLBD [6:0] = 11: 8-bit deactivate code in RIBLBD [7:0] Description
RIBLBA_L[1:0]
3-2
00
RIBLBD_L[1:0]
1-0
01
Table-43 MAINT3: Maintenance Function Control Register 3
(R/W, Address = 0DH,2DH,4DH,6DH,8DH,ADH,CDH,EDH)
Symbol TIBLB[7:0] Bit 7-0 Default Description (000)00001 Defines the user-programmable transmit Inband Loopback activate/deactivate code. The default selection is 00001. TIBLB[7:0] form the 8-bit repeating code TIBLB[6:0] form the 7-bit repeating code TIBLB[5:0] form the 6-bit repeating code TIBLB[4:0] form the 5-bit repeating code
46
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-44 MAINT4: Maintenance Function Control Register 4
(R/W, Address = 0EH,2EH,4EH,6EH,8EH,AEH,CEH,EEH)
Symbol RIBLBA[7:0] Bit 7-0 Default Description (000)00001 Defines the user-programmable receive Inband Loopback activate code. The default selection is 00001. RIBLBA[7:0] form the 8-bit repeating code RIBLBA[6:0] form the 7-bit repeating code RIBLBA[5:0] form the 6-bit repeating code RIBLBA[4:0] form the 5-bit repeating code
Table-45 MAINT5: Maintenance Function Control Register 5
(R/W, Address = 0FH,2FH,4FH,6FH,8FH,AFH,CFH,EFH)
Symbol RIBLBD[7:0] Bit 7-0 Default Description (00)001001 Defines the user-programmable receive Inband Loopback deactivate code. The default selection is 001001. RIBLBD[7:0] form the 8-bit repeating code RIBLBD[6:0] form the 7-bit repeating code RIBLBD[5:0] form the 6-bit repeating code RIBLBD[4:0] form the 5-bit repeating code
Table-46 MAINT6: Maintenance Function Control Register 6
(R/W, Address = 10H,30H,50H,70H,90H,B0H,D0H,F0H)
Symbol BPV_INS Bit 7 6 Default 0 0 Reserved. BPV error insertion A `0' to `1' transition on this bit will cause a single bipolar violation error to be inserted into the transmit data stream. This bit must be cleared and set again for a subsequent error to be inserted. PRBS/QRSS logic error insertion A `0' to `1' transition on this bit will cause a single PRBS/QRSS logic error to be inserted into the transmit PRBS/ QRSS data stream. This bit must be cleared and set again for subsequent error to be inserted. EXZ definition select = 0: ANSI = 1: FCC These bits choose which type of error will be counted = 00: the PRBS logic error is counted by a 16-bit error counter. = 01: the EXZ error is counted by a 16-bit error counter. = 10: the Received CV (BPV) error is counted by a 16-bit error counter. = 11: both CV (BPV) and EXZ errors are counted by a 16-bit error counter. Counter operation mode select = 0: Manual Report Mode = 1: Auto Report Mode = 0: Clear this bit for the next `0' to `1' transition on this bit. = 1: Error counting result is transferred to CNT0 and CNT1 and the error counter is reset. Description
ERR_INS
5
0
EXZ_DEF
4
0
ERR_SEL
3-2
00
CNT_MD
1
0
CNT_TRF
0
0
47
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
4.2.6
INTERRUPT CONTROL REGISTERS
Table-47 INTM0: Interrupt Mask Register 0
(R/W, Address = 11H,31H,51H,71H,91H,B1H,D1H,F1H)
Symbol EQ_IM Bit 7 Default 1 Equalizer out of range interrupt mask = 0: Equalizer out of range interrupt enabled = 1: Equalizer out of range interrupt masked In-band Loopback activate code detect interrupt mask = 0: In-band Loopback activate code detect interrupt enabled = 1: In-band Loopback activate code detect interrupt masked In-band Loopback deactivate code detect interrupt mask = 0: In-band Loopback deactivate code detect interrupt enabled = 1: In-band Loopback deactivate code detect interrupt masked PRBS synchronic signal detect interrupt mask = 0: PRBS synchronic signal detect interrupt enabled = 1: PRBS synchronic signal detect interrupt masked TCLK loss detect interrupt mask = 0: TCLK loss detect interrupt enabled = 1: TCLK loss detect interrupt masked Driver failure interrupt mask = 0: Driver failure interrupt enabled = 1: Driver failure interrupt masked Alarm Indication Signal interrupt mask = 0: Alarm Indication Signal interrupt enabled = 1: Alarm Indication Signal interrupt masked Loss Of Signal interrupt mask = 0: Loss Of Signal interrupt enabled = 1: Loss Of Signal interrupt masked Description
IBLBA_IM
6
1
IBLBD_IM
5
1
PRBS_IM
4
1
TCLK_IM
3
1
DF_IM
2
1
AIS_IM
1
1
LOS_IM
0
1
48
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-48 INTM1: Interrupt Mask Register 1
(R/W, Address = 12H,32H,52H,72H,92H,B2H,D2H,F2H)
Symbol DAC_OV_IM Bit 7 Default 1 DAC arithmetic overflow interrupt mask = 0: DAC arithmetic overflow interrupt enabled = 1: DAC arithmetic overflow interrupt masked JA overflow interrupt mask = 0: JA overflow interrupt enabled = 1: JA overflow interrupt masked JA underflow interrupt mask = 0: JA underflow interrupt enabled = 1: JA underflow interrupt masked PRBS/QRSS logic error detect interrupt mask = 0: PRBS/QRSS logic error detect interrupt enabled = 1: PRBS/QRSS logic error detect interrupt masked Receive excess zeros interrupt mask = 0: Receive excess zeros interrupt enabled = 1: Receive excess zeros interrupt masked Receive error interrupt mask = 0: Receive error interrupt enabled = 1: Receive error interrupt masked One-Second Timer expiration interrupt mask = 0: One-Second Timer expiration interrupt enabled = 1: One-Second Timer expiration interrupt masked Counter overflow interrupt mask = 0: Counter overflow interrupt enabled = 1: Counter overflow interrupt masked Description
JAOV_IM
6
1
JAUD_IM
5
1
ERR_IM
4
1
EXZ_IM
3
1
CV_IM
2
1
TIMER_IM
1
1
CNT_IM
0
1
49
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-49 INTES: Interrupt Trigger Edges Select Register
(R/W, Address = 13H,33H, 53H,73H,93H,B3H,D3H,F3H)
Symbol EQ_IES Bit 7 Default 0 Description This bit determines the Equalizer out of range interrupt event. = 0: interrupt event is defined as a `0' to `1' transition of the EQ_S bit in the STAT0 status register = 1: interrupt event is defined as either a `0' to `1' transition or a `1' to `0' transition of the EQ_S bit in the STAT0 status register. This bit determines the Inband Loopback Activate Code interrupt event. = 0: interrupt event is defined as a `0' to `1' transition of the IBLBA_S bit in the STAT0 status register = 1: interrupt event is defined as either a `0' to `1' transition or a `1' to `0' transition of the IBLBA_S bit in the STAT0 status register. This bit determines the Inband Loopback Deactivate Code interrupt event. = 0: interrupt event is defined as a `0' to `1' transition of the IBLBD_S bit in the STAT0 status register = 1: interrupt event is defined as either a `0' to `1' transition or a `1' to `0' transition of the IBLBD_S bit in the STAT0 status register. This bit determines the PRBS/QRSS synchronization status interrupt event. = 0: interrupt event is defined as a `0' to `1' transition of the PRBS_S bit in the STAT0 status register = 1: interrupt event is defined as either a `0' to `1' transition or a `1' to `0' transition of the PRBS_S bit in the STAT0 status register. This bit determines the TCLK Loss interrupt event. = 0: interrupt event is defined as a `0' to `1' transition of the TCLK_LOS bit in the STAT0 status register = 1: interrupt event is defined as either a `0' to `1' transition or a `1' to `0' transition of the TCLK_LOS bit in the STAT0 status register. This bit determines the Driver Failure interrupt event. = 0: interrupt event is defined as a `0' to `1' transition of the DF_S bit in the STAT0 status register = 1: interrupt event is defined as either a `0' to `1' transition or a `1' to `0' transition of the DF_S bit in the STAT0 status register. This bit determines the AIS interrupt event. = 0: interrupt event is defined as a `0' to `1' transition of the AIS_S bit in the STAT0 status register = 1: interrupt event is defined as either a `0' to `1' transition or a `1' to `0' transition of the AIS_S bit in the STAT0 status register. This bit determines the LOS interrupt event. = 0: interrupt event is defined as a `0' to `1' transition of the LOS_S bit in the STAT0 status register = 1: interrupt event is defined as either a `0' to `1' transition or a `1' to `0' transition of the LOS_S bit in the STAT0 status register.
IBLBA_IES
6
0
IBLBD_IES
5
0
PRBS_IES
4
0
TCLK_IES
3
0
DF_IES
2
0
AIS_IES
1
0
LOS_IES
0
0
50
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
4.2.7
LINE STATUS REGISTERS
Table-50 STAT0: Line Status Register 0 (real time status monitor)
(R, Address = 14H,34H,54H,74H,94H,B4H,D4H,F4H)
Symbol EQ_S Bit 7 Default 0 Equalizer status indication = 0: In range = 1: out of range Inband Loopback activate code receive status indication = 0: no Inband Loopback activate code is detected = 1: activate code has been detected for more than t ms. Even there is bit error, this bit remains set as long as the bit error rate is less than 10-2. Note1: Automatic remote loopback switching is disabled (ARLP = 0), t = 40 ms. If automatic remote loopback switching is enabled (ARLP = 1), t = 5.1 s. The rising edge of this bit activates the remote loopback operation in local end. Note2: If IBLBA_IM=0 and IBLBA_IES=0, a `0' to `1' transition on this bit will cause an activate code detect interrupt. If IBLBA_IM=0 and IBLBA_IES=1, any changes on this bit will cause an activate code detect interrupt. IBLBD_S 5 0 Inband Loopback deactivate code receive status indication = 0: no Inband Loopback deactivate code is detected = 1: the Inband Loopback deactivate code has been detected for more than t. Even there is a bit error, this bit remains set as long as the bit error rate is less than 10-2. Note1: Automatic remote loopback switching is disabled (ARLP = 0), t = 40 ms.If automatic remote loopback switching is enabled (ARLP = 1), t= 5.1 s. The rising edge of this bit disables the remote loopback operation. Note2: If IBLBD_IM=0 and IBLBD_IES=0, a `0' to `1' transition on this bit will cause a deactivate code detect interrupt. If IBLBD_IM=0 and IBLBD_IES=1, any changes on this bit will cause a deactivate code detect interrupt. PRBS_S 4 0 Synchronous status indication of PRBS/QRSS (real time) = 0: 215-1 (E1) PRBS or 220-1 (T1/J1) QRSS is not detected = 1: 215-1 (E1) PRBS or 220-1 (T1/J1) QRSS is detected. Note: If PRBS_IM=0 and PRBS_IES=0, a `0' to `1' transition on this bit will cause a synchronous status detect interrupt. If PRBS_IM=0 and PRBS_IES=1, any changes on this bit will cause a synchronous status detect interrupt. TCLK_LOS 3 0 TCLKn loss indication = 0: normal = 1: TCLKn pin has not toggled for more than 70 MCLK cycles. Note: If TCLK_IM=0 and TCLK_IES=0, a `0' to `1' transition on this bit will cause an interrupt. If TCLK_IM=0 and TCLK_IES=1, any changes on this bit will cause an interrupt. Description
IBLBA_S
6
0
51
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-50 STAT0: Line Status Register 0 (real time status monitor) (Continued)
(R, Address = 14H,34H,54H,74H,94H,B4H,D4H,F4H)
Symbol DF_S Bit 2 Default 0 Line driver status indication = 0: normal operation = 1: line driver short circuit is detected. Note: If DF_IM=0 and DF_IES=0, a `0' to `1' transition on this bit will cause an interrupt. If DF_IM=0 and DF_IES=1, any changes on this bit will cause an interrupt. AIS_S 1 0 Alarm Indication Signal status detection = 0: no AIS signal is detected in the receive path = 1: AIS signal is detected in the receive path Note: If AIS_IM=0 and AIS_IES=0, a `0' to `1' transition on this bit will cause an interrupt. If AIS_IM=0 and AIS_IES=1, any changes on this bit will cause an interrupt. LOS_S 0 0 Loss of Signal status detection = 0: Loss of signal on RTIP/RRING is not detected = 1: Loss of signal on RTIP/RRING is detected Note: IF LOS_IM=0 and LOS_IES=0, a `0' to `1' transition on this bit will cause an interrupt. IF LOS_IM=0 and LOS_IES=1, any changes on this bit will cause an interrupt. Description
52
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-51 STAT1: Line Status Register 1 (real time status monitor)
(R, Address = 15H,35H, 55H,75H,95H,B5H, D5H, F5H)
Symbol RLP_S Bit 7-6 5 Default 00 0 Reserved Indicating the status of Remote Loopback = 0: The remote loopback is inactive. = 1: The remote loopback is active (closed). Line Attenuation Indication in dB relative to a 3 V peak pulse level 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 10001 10010 10011 10100 10101 10110-11111 0 to 2 dB 2 to 4 dB 4 to 6 dB 6 to 8 dB 8 to 10 dB 10 to 12 dB 12 to 14 dB 14 to 16 dB 16 to 18 dB 18 to 20 dB 20 to 22 dB 22 to 24 dB 24 to 26 dB 26 to 28 dB 28 to 30 dB 30 to 32 dB 32 to 34 dB 34 to 36 dB 36 to 38 dB 38 to 40 dB 40 to 42 dB 42 to 44 dB >44 dB Description
LATT[4:0]
4-0
00000
53
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
4.2.8
INTERRUPT STATUS REGISTERS
Table-52 INTS0: Interrupt Status Register 0
(this register is reset after a read operation) (R, Address = 16H,36H, 56H,76H,96H,B6H, D6H, F6H)
Symbol EQ_IS Bit 7 Default 0 Description This bit indicates the occurrence of Equalizer out of range interrupt event. = 0: no interrupt event from the Equalizer out of range occurred = 1: interrupt event from the Equalizer out of range occurred This bit indicates the occurrence of the Inband Loopback Activate Code interrupt event. = 0: no Inband Loopback Activate Code interrupt event occurred = 1: Inband Loopback Activate Code Interrupt event occurred This bit indicates the occurrence of the Inband Loopback Deactivate Code interrupt event. = 0: no Inband Loopback Deactivate Code interrupt event occurred = 1: interrupt event of the received inband loopback deactivate code occurred. This bit indicates the occurrence of the interrupt event generated by the PRBS/QRSS synchronization status. = 0: no PRBS/QRSS synchronization status interrupt event occurred = 1: PRBS/QRSS synchronization status interrupt event occurred This bit indicates the occurrence of the interrupt event generated by the TCLKn loss detection. = 0: no TCLKn loss interrupt event. = 1:TCLKn loss interrupt event occurred. This bit indicates the occurrence of the interrupt event generated by the Driver Failure. = 0: no Driver Failure interrupt event occurred = 1: Driver Failure interrupt event occurred This bit indicates the occurrence of the AIS (Alarm Indication Signal) interrupt event. = 0: no AIS interrupt event occurred = 1: AIS interrupt event occurred This bit indicates the occurrence of the LOS (Loss of signal) interrupt event. = 0: no LOS interrupt event occurred = 1: LOS interrupt event occurred
IBLBA_IS
6
0
IBLBD_IS
5
0
PRBS_IS
4
0
TCLK_LOS_IS
3
0
DF_IS
2
0
AIS_IS
1
0
LOS_IS
0
0
54
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-53 INTS1: Interrupt Status Register 1
(this register is reset and relevant interrupt request is cleared after a read) (R, Address = 17H,37H, 57H,77H,97H,B7H, D7H, F7H)
Symbol DAC_OV_IS Bit 7 Default 0 Description This bit indicates the occurrence of the pulse amplitude overflow of Arbitrary Waveform Generator interrupt event. = 0: no pulse amplitude overflow of Arbitrary Waveform Generator interrupt event occurred = 1: the pulse amplitude overflow of Arbitrary Waveform Generator interrupt event occurred This bit indicates the occurrence of the Jitter Attenuator Overflow interrupt event. = 0: no JA overflow interrupt event occurred = 1: A overflow interrupt event occurred This bit indicates the occurrence of the Jitter Attenuator Underflow interrupt event. = 0: no JA underflow interrupt event occurred = 1: JA underflow interrupt event occurred This bit indicates the occurrence of the interrupt event generated by the detected PRBS/QRSS logic error. = 0: no PRBS/QRSS logic error interrupt event occurred = 1: PRBS/QRSS logic error interrupt event occurred This bit indicates the occurrence of the Excessive Zeros interrupt event. = 0: no excessive zeros interrupt event occurred = 1: EXZ interrupt event occurred This bit indicates the occurrence of the Code Violation interrupt event. = 0: no code violation interrupt event occurred = 1: code violation interrupt event occurred This bit indicates the occurrence of the One-Second Timer Expiration interrupt event. = 0: no one-second timer expiration interrupt event occurred = 1: one-second timer expiration interrupt event occurred This bit indicates the occurrence of the Counter Overflow interrupt event. = 0: no counter overflow interrupt event occurred = 1: counter overflow interrupt event occurred
JAOV_IS
6
0
JAUD_IS
5
0
ERR_IS
4
0
EXZ_IS
3
0
CV_IS
2
0
TMOV_IS
1
0
CNT_OV_IS
0
0
4.2.9
COUNTER REGISTERS
Table-54 CNT0: Error Counter L-byte Register 0
(R, Address = 18H,38H, 58H,78H,98H,B8H, D8H, F8H)
Symbol CNT_L[7:0] Bit 7-0 Default 00H Description This register contains the lower eight bits of the 16-bit error counter. CNT_L[0] is the LSB.
Table-55 CNT1: Error Counter H-byte Register 1
(R, Address = 19H,39H, 59H,79H,99H,B9H,D9H,F9H)
Symbol CNT_H[7:0] Bit 7-0 Default 00H Description This register contains the upper eight bits of the 16-bit error counter. CNT_H[7] is the MSB.
55
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
4.2.10 TRANSMIT AND RECEIVE TERMINATION REGISTER
Table-56 TERM: Transmit and Receive Termination Configuration Register
(R/W, Address = 1AH,3AH, 5AH,7AH,9AH,BAH,DAH,FAH)
Symbol T_TERM[2:0] Bit 7-6 5-3 Default 00 000 Reserved These bits select the internal termination for transmit line impedance matching. = 000: internal 75 impedance matching = 001: internal 120 impedance matching = 010: internal 100 impedance matching = 011: internal 110 impedance matching =1xx: Selects external impedance matching resistors for E1 mode only. T1/J1 does not require external impedance resistors (see Table-14). These bits select the internal termination for receive line impedance matching. = 000: internal 75 impedance matching = 001: internal 120 impedance matching = 010: internal 100 impedance matching = 011: internal 110 impedance matching = 1xx: Selects external impedance matching resistors (see Table-15). Description
R_TERM[2:0]
2-0
000
56
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
5 IEEE STD 1149.1 JTAG TEST ACCESS PORT
The IDT82V2088 supports the digital Boundary Scan Specification as described in the IEEE 1149.1 standards. The boundary scan architecture consists of data and instruction registers plus a Test Access Port (TAP) controller. Control of the TAP is performed through signals applied to the Test Mode Select (TMS) and Test
Clock (TCK) pins. Data is shifted into the registers via the Test Data Input (TDI) pin, and shifted out of the registers via the Test Data Output (TDO) pin. Both TDI and TDO are clocked at a rate determined by TCK. The JTAG boundary scan registers include BSR (Boundary Scan Register), IDR (Device Identification Register), BR (Bypass Register) and IR (Instruction Register). These will be described in the following pages. Refer to for architecture.
Digital output pins
Digital input pins
parallel latched output
BSR (Boundary Scan Register)
IDR (Device Identification Register) TDI BR (Bypass Register)
MUX
MUX
IR (Instruction Register)
TDO
Control<6:0> TMS TRST TCK TAP (Test Access Port) Controller Select Tristate Enable
Figure-22 JTAG Architecture
57
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
5.1 JTAG INSTRUCTIONS AND INSTRUCTION REGISTER
The IR (Instruction Register) with instruction decode block is used to select the test to be executed or the data register to be accessed or both. The instructions are shifted in LSB first to this 3-bit register. See Table57 for details of the codes and the instructions related.
Table-57 Instruction Register Description
IR CODE 000 INSTRUCTION Extest COMMENTS The external test instruction allows testing of the interconnection to other devices. When the current instruction is the EXTEST instruction, the boundary scan register is placed between TDI and TDO. The signal on the input pins can be sampled by loading the boundary scan register using the Capture-DR state. The sampled values can then be viewed by shifting the boundary scan register using the Shift-DR state. The signal on the output pins can be controlled by loading patterns shifted in through input TDI into the boundary scan register using the Update-DR state.
100
Sample / Preload The sample instruction samples all the device inputs and outputs. For this instruction, the boundary scan register is placed between TDI and TDO. The normal path between IDT82V2088 logic and the I/O pins is maintained. Primary device inputs and outputs can be sampled by loading the boundary scan register using the Capture-DR state. The sampled values can then be viewed by shifting the boundary scan register using the Shift-DR state. Idcode Bypass The identification instruction is used to connect the identification register between TDI and TDO. The device's identification code can then be shifted out using the Shift-DR state. The bypass instruction shifts data from input TDI to output TDO with one TCK clock period delay. The instruction is used to bypass the device.
110 111
5.2
5.2.1
JTAG DATA REGISTER
DEVICE IDENTIFICATION REGISTER (IDR)
5.2.2
BYPASS REGISTER (BR)
The IDR can be set to define the producer number, part number and the device revision, which can be used to verify the proper version or revision number that has been used in the system under test. The IDR is 32 bits long and is partitioned as in Table-58. Data from the IDR is shifted out to TDO LSB first.
The BR consists of a single bit. It can provide a serial path between the TDI input and TDO output, bypassing the BSR to reduce test access times. 5.2.3 BOUNDARY SCAN REGISTER (BSR) The BSR can apply and read test patterns in parallel to or from all the digital I/O pins. The BSR is a 98 bits long shift register and is initialized and read using the instruction EXTEST or SAMPLE/PRELOAD. Each pin is related to one or more bits in the BSR. For details, please refer to the BSDL file.
Table-58 Device Identification Register Description
Bit No. 0 1-11 12-27 28-31
Comments
Set to `1' Producer Number Part Number Device Revision
58
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
5.2.4
TEST ACCESS PORT CONTROLLER
The TAP controller is a 16-state synchronous state machine. Figure-23 shows its state diagram following the description of each state. Note that the figure contains two main branches to access either the data or instruc-
tion registers. The value shown next to each state transition in this figure states the value present at TMS at each rising edge of TCK. Please refer to Table-59 for details of the state description.
Table-59 TAP Controller State Description
STATE Test Logic Reset DESCRIPTION In this state, the test logic is disabled. The device is set to normal operation. During initialization, the device initializes the instruction register with the IDCODE instruction. Regardless of the original state of the controller, the controller enters the Test-Logic-Reset state when the TMS input is held high for at least 5 rising edges of TCK. The controller remains in this state while TMS is high. The device processor automatically enters this state at power-up. This is a controller state between scan operations. Once in this state, the controller remains in the state as long as TMS is held low. The instruction register and all test data registers retain their previous state. When TMS is high and a rising edge is applied to TCK, the controller moves to the Select-DR state. This is a temporary controller state and the instruction does not change in this state. The test data register selected by the current instruction retains its previous state. If TMS is held low and a rising edge is applied to TCK when in this state, the controller moves into the Capture-DR state and a scan sequence for the selected test data register is initiated. If TMS is held high and a rising edge applied to TCK, the controller moves to the Select-IR-Scan state. In this state, the Boundary Scan Register captures input pin data if the current instruction is EXTEST or SAMPLE/PRELOAD. The instruction does not change in this state. The other test data registers, which do not have parallel input, are not changed. When the TAP controller is in this state and a rising edge is applied to TCK, the controller enters the Exit1-DR state if TMS is high or the Shift-DR state if TMS is low. In this controller state, the test data register connected between TDI and TDO as a result of the current instruction shifts data on stage toward its serial output on each rising edge of TCK. The instruction does not change in this state. When the TAP controller is in this state and a rising edge is applied to TCK, the controller enters the Exit1-DR state if TMS is high or remains in the Shift-DR state if TMS is low. This is a temporary state. While in this state, if TMS is held high, a rising edge applied to TCK causes the controller to enter the Update-DR state, which terminates the scanning process. If TMS is held low and a rising edge is applied to TCK, the controller enters the Pause-DR state. The test data register selected by the current instruction retains its previous value and the instruction does not change during this state. The pause state allows the test controller to temporarily halt the shifting of data through the test data register in the serial path between TDI and TDO. For example, this state could be used to allow the tester to reload its pin memory from disk during application of a long test sequence. The test data register selected by the current instruction retains its previous value and the instruction does not change during this state. The controller remains in this state as long as TMS is low. When TMS goes high and a rising edge is applied to TCK, the controller moves to the Exit2-DR state. This is a temporary state. While in this state, if TMS is held high, a rising edge applied to TCK causes the controller to enter the Update-DR state, which terminates the scanning process. If TMS is held low and a rising edge is applied to TCK, the controller enters the Shift-DR state. The test data register selected by the current instruction retains its previous value and the instruction does not change during this state. The Boundary Scan Register is provided with a latched parallel output to prevent changes while data is shifted in response to the EXTEST and SAMPLE/PRELOAD instructions. When the TAP controller is in this state and the Boundary Scan Register is selected, data is latched into the parallel output of this register from the shift-register path on the falling edge of TCK. The data held at the latched parallel output changes only in this state. All shift-register stages in the test data register selected by the current instruction retain their previous value and the instruction does not change during this state. This is a temporary controller state. The test data register selected by the current instruction retains its previous state. If TMS is held low and a rising edge is applied to TCK when in this state, the controller moves into the Capture-IR state, and a scan sequence for the instruction register is initiated. If TMS is held high and a rising edge is applied to TCK, the controller moves to the Test-Logic-Reset state. The instruction does not change during this state. In this controller state, the shift register contained in the instruction register loads a fixed value of '100' on the rising edge of TCK. This supports fault-isolation of the board-level serial test data path. Data registers selected by the current instruction retain their value and the instruction does not change during this state. When the controller is in this state and a rising edge is applied to TCK, the controller enters the Exit1-IR state if TMS is held high, or the Shift-IR state if TMS is held low. In this state, the shift register contained in the instruction register is connected between TDI and TDO and shifts data one stage towards its serial output on each rising edge of TCK. The test data register selected by the current instruction retains its previous value and the instruction does not change during this state. When the controller is in this state and a rising edge is applied to TCK, the controller enters the Exit1IR state if TMS is held high, or remains in the Shift-IR state if TMS is held low. This is a temporary state. While in this state, if TMS is held high, a rising edge applied to TCK causes the controller to enter the Update-IR state, which terminates the scanning process. If TMS is held low and a rising edge is applied to TCK, the controller enters the Pause-IR state. The test data register selected by the current instruction retains its previous value and the instruction does not change during this state. 59
Run-Test/Idle
Select-DR-Scan
Capture-DR
Shift-DR
Exit1-DR
Pause-DR
Exit2-DR
Update-DR
Select-IR-Scan
Capture-IR
Shift-IR
Exit1-IR
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-59 TAP Controller State Description (Continued)
STATE Pause-IR DESCRIPTION The pause state allows the test controller to temporarily halt the shifting of data through the instruction register. The test data register selected by the current instruction retains its previous value and the instruction does not change during this state. The controller remains in this state as long as TMS is low. When TMS goes high and a rising edge is applied to TCK, the controller moves to the Exit2-IR state. This is a temporary state. While in this state, if TMS is held high, a rising edge applied to TCK causes the controller to enter the Update-IR state, which terminates the scanning process. If TMS is held low and a rising edge is applied to TCK, the controller enters the Shift-IR state. The test data register selected by the current instruction retains its previous value and the instruction does not change during this state. The instruction shifted into the instruction register is latched into the parallel output from the shift-register path on the falling edge of TCK. When the new instruction has been latched, it becomes the current instruction. The test data registers selected by the current instruction retain their previous value.
Exit2-IR
Update-IR
1
Test-logic Reset 0
0 Run Test/Idle
1
Select-DR 0 1 Capture-DR 0
1
Select-IR 0 1 Capture-IR 0
1
0 Shift-DR 1 Exit1-DR 0 0 Pause-DR 1 0 Exit2-DR 1 Update-DR 1 0 0 Pause-IR 1 Exit2-IR 1 Update-IR 1 0 1 Shift-IR 1 Exit1-IR 0
0
1
0
Figure-23 JTAG State Diagram
60
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
6
TEST SPECIFICATIONS
Table-60 Absolute Maximum Rating
Symbol VDDA, VDDD VDDIO VDDT1-8 VDDR1-8 Core Power Supply I/O Power Supply Transmit Power Supply Receive Power Supply Input Voltage, Any Digital Pin Vin Input Voltage, Any RTIP and RRING pin1 ESD Voltage, any pin Transient latch-up current, any pin Iin Input current, any digital pin
4
Parameter
Min -0.5 -0.5 -0.5 -0.5 GND-0.5 GND-0.5 2000 2 500 3
Max 4.6 4.6 4.6 4.6 5.5 VDDR+0.5
Unit V V V V V V V
100 -10 10 100 3.35 2.63 120 -65 +150
mA mA mA W W C C
DC Input current, any analog pin 4 Pd Tc Ts Maximum power dissipation in package DR208 Maximum power dissipation in package BB208 Case Temperature Storage Temperature
CAUTION: Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 1.Reference to ground 2.Human body model 3.Charge device model 4.Constant input current
Table-61 Recommended Operation Conditions
Symbol VDDA,VDDD VDDIO VDDT VDDR TA Core Power Supply I/O Power Supply Transmitter Power Supply Receive Power Supply Ambient operating temperature E1, 75 Load 50% ones density data 100% ones density data E1, 120 Load Total current dissipation1,2,3 50% ones density data 100% ones density data T1, 100 Load 50% ones density data 100% ones density data J1, 110 Load 50% ones density data 100% ones density data 440 560 460 580 mA 510 710 530 730 mA 450 540 470 560 mA 460 570 480 590 mA Parameter Min 3.13 3.13 3.13 3.13 -40 Typ 3.3 3.3 3.3 3.3 25 Max 3.47 3.47 3.47 3.47 85 Unit V V V V C
1.Power consumption includes power consumption on device and load. Digital levels are 10% of the supply rails and digital outputs driving a 50 pF capacitive load. 2.Maximum power consumption over the full operating temperature and power supply voltage range. 3.In short haul mode, if internal impedance matching is chosen, E1 75 power dissipation values are measured with template PULS[3:0] = 0000; E1 120 power dissipation values are measured with template PULS[3:0] = 0001; T1 power dissipation values are measured with template PULS[3:0] = 0110; J1 power dissipation values are measured with template PULS[3:0] = 0111. 61
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-62 Power Consumption
Symbol E1, 3.3 V, 75 Load 50% ones density data: 100% ones density data: E1, 3.3 V, 120 Load 50% ones density data: 100% ones density data: T1, 3.3 V, 100 Load3 50% ones density data: 100% ones density data: J1, 3.3 V, 110 Load 50% ones density data: 100% ones density data: 1450 1850 mW 2020 1490 1780 1680 2340 1950 2540 mW 1520 1880 2050 mW Parameter Min Typ Max1,2 Unit
mW
1.Maximum power and current consumption over the full operating temperature and power supply voltage range. Includes all channels. 2.Power consumption includes power absorbed by line load and external transmitter components. 3.T1 is measured with maximum cable length.
Table-63 DC Characteristics
Symbol VIL VIH VOL VOH VMA II Input High Voltage Output Low level Voltage (Iout=1.6mA) Output High level Voltage (Iout=400A) Analog Input Quiescent Voltage (RTIP, RRING pin while floating) Input Leakage Current TMS, TDI, TRST All other digital input pins Tri-state Leakage Current Input capacitance Output load capacitance Output load capacitance (bus pins) Parameter Input Low Level Voltage Min 2.0 2.4 Typ 1.5 Max 0.8 0.4 VDDIO Unit V V V V V
-10 -10
50 10 10 15 50 100
A A A pF pF pF
IZL Ci Co Co
62
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-64 E1 Receiver Electrical Characteristics
Symbol Parameter Receiver sensitivity Short haul with cable loss@1024kHz: Long haul with cable loss@1024kHz: Analog LOS level Short haul Long haul Allowable consecutive zeros before LOS G.775: I.431/ETSI300233: LOS reset Receive Intrinsic Jitter 20Hz - 100kHz Input Jitter Tolerance 1 Hz - 20 Hz 20 Hz - 2.4 KHz 18 KHz - 100 KHz ZDM Receiver Differential Input Impedance Input termination resistor tolerance RRX Receive Return Loss 51 KHz - 102 KHz 102 KHz - 2.048 MHz 2.048 MHz - 3.072 MHz Receive path delay Single rail Dual rail 20 20 20 7 2 37 5 2 20 1% dB dB dB U.I. U.I. G.703 Internal termination 12.5 0.05 800 -4 32 2048 % ones U.I. U.I. U.I. U.I. K G.775, ETSI 300 233 JA enabled G.823, with 6 dB cable attenuation -48 Min Typ Max -10 -43 Unit dB Test conditions
mVp-p dB
A LOS level is programmable for Long Haul
Internal mode
RPD
JA disabled
63
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-65 T1/J1 Receiver Electrical Characteristics
Symbol Parameter receiver sensitivity Short haul with cable loss@772kHz: Long haul with cable loss@772kHz: Analog LOS level Short haul Long haul Allowable consecutive zeros before LOS T1.231-1993 I.431 LOS reset Receive Intrinsic Jitter 10 Hz - 8 KHz 10 Hz - 40 KHz 8 KHz - 40 KHz Wide band Input Jitter Tolerance 0.1 Hz - 1 Hz 4.9 Hz - 300 Hz 10 KHz - 100 KHz ZDM RRX Receiver Differential Input Impedance Input termination resistor tolerance Receive Return Loss 39 KHz - 77 KHz 77 KHz - 1.544 MHz 1.544 MHz - 2.316 MHz Receive path delay Single rail Dual rail 20 20 20 7 2 138.0 28.0 0.4 20 1% dB dB dB U.I. U.I. G.703 Internal termination JA disabled 12.5 0.02 0.025 0.025 0.050 800 -4 175 1544 % ones U.I. U.I. U.I. U.I. U.I. U.I. U.I. K AT&T62411 G.775, ETSI 300 233 JA enabled ( in receive path) -48 Min Typ Max -10 -36 Unit dB Test conditions
mVp-p dB
A LOS level is programmable for Long Haul
Internal mode
RPD
64
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-66 E1 Transmitter Electrical Characteristics
Symbol Vo-p Output pulse amplitudes E1, 75 load E1, 120 load Zero (space) level E1, 75 load E1, 120 load Transmit amplitude variation with supply Difference between pulse sequences for 17 consecutive pulses (T1.102) Tpw Output Pulse Width at 50% of nominal amplitude Ratio of the amplitudes of Positive and Negative Pulses at the center of the pulse interval (G.703) Ratio of the width of Positive and Negative Pulses at the center of the pulse interval (G.703) RTX Transmit Return Loss (G.703) 51 KHz - 102 KHz 102 KHz - 2.048 MHz 2.048 MHz - 3.072 MHz JTXp-p Td Intrinsic Transmit Jitter (TCLK is jitter free) 20 Hz - 100 KHz Transmit path delay (JA is disabled) Single rail Dual rail Isc Line short circuit current 8.5 4.5 100 U.I. U.I. mA Ip-p 0.050 U.I. 20 15 12 dB dB dB 232 0.95 0.95 244 Parameter Min 2.14 2.7 -0.237 -0.3 -1 Typ 2.37 3.0 Max 2.60 3.3 0.237 0.3 +1 200 256 1.05 1.05 Unit V V V V % mV ns
Vo-s
65
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-67 T1/J1 Transmitter Electrical Characteristics
Symbol Vo-p Vo-s Output pulse amplitudes Zero (space) level Transmit amplitude variation with supply Difference between pulse sequences for 17 consecutive pulses(T1.102) TPW Output Pulse Width at 50% of nominal amplitude Pulse width variation at the half amplitude (T1.102) Imbalance between Positive and Negative Pulses amplitude (T1.102) Output power level (T1.102) @772kHz @1544kHz (referenced to power at 772kHz) RTX Transmit Return Loss 39 KHz - 77 KHz 77 KHz - 1.544 MHz 1.544 MHz - 2.316 MHz JTXP-P Intrinsic Transmit Jitter (TCLK is jitter free) 10 Hz - 8 KHz 8 KHz - 40 KHz 10 Hz - 40 KHz wide band Td Transmit path delay (JA is disabled) Single rail Dual rail ISC Line short circuit current 8.5 4.5 100 U.I. U.I. mA Ip-p 0.020 0.025 0.025 0.050 U.I.p-p U.I.p-p U.I.p-p U.I.p-p 20 15 12 dB dB dB 0.95 338 350 Parameter Min 2.4 -0.15 -1 Typ 3.0 Max 3.6 0.15 +1 200 362 20 1.05 Unit V V % mV ns ns
12.6 -29
17.9
dBm dBm
66
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-68 Transmitter and Receiver Timing Characteristics
Symbol MCLK frequency E1: T1/J1: MCLK tolerance MCLK duty cycle Transmit path TCLK frequency E1: T1/J1: TCLK tolerance TCLK Duty Cycle t1 t2 Transmit Data Setup Time Transmit Data Hold Time Delay time of THZ low to driver high impedance Delay time of TCLK low to driver high impedance Receive path Clock recovery capture E1 range 1 T1/J1 RCLK duty cycle 2 t4 RCLK pulse width 2 E1: T1/J1: t5 RCLK pulse width low time E1: T1/J1: t6 RCLK pulse width high time E1: T1/J1: Rise/fall time 3 t7 Receive Data Setup Time E1: T1/J1: t8 Receive Data Hold Time E1: T1/J1: 200 200 244 324 ns 200 200 244 324 ns 203 259 244 324 285 389 20 ns ns 203 259 244 324 285 389 ns 457 607 488 648 519 689 ns 40 80 180 50 60 % ppm 75 -50 10 40 40 10 2.048 1.544 +50 90 MHz ppm % ns ns us U.I. -100 30 2.048/49.152 1.544/37.056 100 70 MHz ppm % Parameter Min Typ Max Unit
1.Relative to nominal frequency, MCLK= 100 ppm 2.RCLK duty cycle widths will vary depending on extent of received pulse jitter displacement. Maximum and minimum RCLK duty cycles are for worst case jitter conditions (0.2UI displacement for E1 per ITU G.823). 3.For all digital outputs. C load = 15pF
67
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
TCLKn
t1
t2
TDn/TDPn TDNn
Figure-24 Transmit System Interface Timing
t4 RCLKn t6 t5
t7 RDPn/RDn (RCLK_SEL = 0) RDNn/CVn
t8
t7 RDPn/RDn (RCLK_SEL = 1) RDNn/CVn
t8
Figure-25 Receive System Interface Timing
Table-69 Jitter Tolerance
Jitter Tolerance E1: 1 Hz 20 Hz - 2.4 KHz 18 KHz - 100 KHz T1/J1: 1 Hz 4.9 Hz - 300 Hz 10 KHz - 100 KHz Min 37 1.5 0.2 138.0 28.0 0.4 Typ Max Unit U.I. U.I. U.I. U.I. U.I. U.I. Standard G.823 Cable attenuation is 6dB AT&T 62411
68
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Figure-26 E1 Jitter Tolerance Performance
Figure-27 T1/J1 Jitter Tolerance Performance
69
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-70 Jitter Attenuator Characteristics
Parameter Jitter Transfer Function Corner (-3dB) Frequency E1, 32/64/128 bits FIFO JABW = 0: JABW = 1: T1/J1, 32/64/128 bits FIFO JABW = 0: JABW = 1: Jitter Attenuator E1: (G.736) @ 3 Hz @ 40 Hz @ 400 Hz @ 100 kHz T1/J1: (Per AT&T pub.62411) @ 1 Hz @ 20 Hz @ 1 kHz @ 1.4 kHz @ 70 kHz Jitter Attenuator Latency Delay 32 bits FIFO: 64 bits FIFO: 128 bits FIFO: Input jitter tolerance before FIFO overflow or underflow 32 bits FIFO: 64 bits FIFO: 128 bits FIFO: 16 32 64 28 58 120 U.I. U.I. U.I. U.I. U.I. U.I. -0.5 -0.5 +19.5 +19.5 0 0 +33.3 40 40 6.8 0.9 5 1.25 Hz Hz Hz Hz Min Typ Max Unit
dB
70
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Figure-28 E1 Jitter Transfer Performance
Figure-29 T1/J1 Jitter Transfer Performance
71
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-71 JTAG Timing Characteristics
Symbol t1 t2 t3 t4 TCK Period TMS to TCK Setup Time TDI to TCK Setup Time TCK to TMS Hold Time TCK to TDI Hold Time TCK to TDO Delay Time Parameter Min 100 25 25 50 Typ Max Unit ns ns ns ns
t1 TCK
t2 TMS TDI
t3
t4
TDO
Figure-30 JTAG Interface Timing
72
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
7
7.1
MICROCONTROLLER INTERFACE TIMING CHARACTERISTICS
SERIAL INTERFACE TIMING
Table-72 Serial Interface Timing Characteristics
Symbol t1 t2 t3 t4 t5 t6 t7 t10 t11 SCLK High Time SCLK Low Time Active CS to SCLK Setup Time Last SCLK Hold Time to Inactive CS Time CS Idle Time SDI to SCLK Setup Time SCLK to SDI Hold Time SCLK to SDO Valid Delay Time Inactive CS to SDO tri-state Hold Time Parameter Min 82 82 5 41 41 0 62 75 70 Typ Max Unit ns ns ns ns ns ns ns ns ns Comments
CS t3 SCLK t6 SDI LSB t7 LSB t7 MSB t1 t2 t4 t5
Figure-31 Serial Interface Write Timing
1 SCLK CS SDO
t10 t4
2
3
4
5
15
16
17
18
19
20
21
22
23
24
0
1
2
3
4
5
6
t11 7
Figure-32 Serial Interface Read Timing with SCLKE=1
1 SCLK CS SDO t10 0 1 2 3 4 5 6 t4 t11 7 2 3 4 5 15 16 17 18 19 20 21 22 23 24
Figure-33 Serial Interface Read Timing with SCLKE=0
73
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
7.2
PARALLEL INTERFACE TIMING
Table-73 Non_multiplexed Motorola Read Timing Characteristics
Symbol tRC tDW tRWV tRWH tAV tADH tPRD tDAZ tRecovery Read Cycle Time Valid DS Width Delay from DS to Valid Read Signal R/W to DS Hold Time Delay from DS to Valid Address Address to DS Hold Time DS to Valid Read Data Propagation Delay Delay from DS inactive to data bus High Impedance Recovery Time from Read Cycle 5 5 65 175 20 65 15 Parameter Min 190 180 15 Max Unit ns ns ns ns ns ns ns ns ns
tRC tDW DS+CS tRWH tRWV R/W tADH tAV
tRecovery
A[x:0]
tPRD READ D[7:0]
Valid Address tDAZ Valid Data
Figure-34 Non_multiplexed Motorola Read Timing
74
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-74 Non_multiplexed Motorola Write Timing Characteristics
Symbol tWC tDW tRWV tRWH tAV tAH tDV tDHW tRecovery Write Cycle Time Valid DS Width Delay from DS to Valid Write Signal R/W to DS Hold Time Delay from DS to Valid Address Address to DS Hold Time Delay from DS to Valid Write Data Write Data to DS Hold Time Recovery Time from Write Cycle 65 5 65 15 65 15 Parameter Min 120 100 15 Max Unit ns ns ns ns ns ns ns ns ns
tWC DS+CS tDW tRWH R/W tRWV
tRecovery
tAV A[x:0]
tAH Valid Address tDHW Valid Data
tDV Write D[7:0]
Figure-35 Non_multiplexed Motorola Write Timing
75
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-75 Non_multiplexed Intel Read Timing Characteristics
Symbol tRC tRDW tAV tAH tPRD tDAZ tRecovery Read Cycle Time Valid RD Width Delay from RD to Valid Address Address to RD Hold Time RD to Valid Read Data Propagation Delay Delay from RD inactive to data bus High Impedance Recovery Time from Read Cycle 5 5 65 175 20 Parameter Min 190 180 15 Max Unit ns ns ns ns ns ns ns
tRC tRDW
tRecovery
CS+RD tAH tAV A[x:0] tPRD READ D[7:0] Valid Data Valid Address tDAZ
Note: WR should be tied to high
Figure-36 Non_multiplexed Intel Read Timing
76
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
Table-76 Non_multiplexed Intel Write Timing Characteristics
Symbol tWC tWRW tAV tAH tDV tDHW tRecovery Write Cycle Time Valid WR Width Delay from WR to Valid Address Address to WR Hold Time Delay from WR to Valid Write Data Write Data to WR Hold Time Recovery Time from Write Cycle 65 5 65 15 Parameter Min 120 100 15 Max Unit ns ns ns ns ns ns ns
tWC tWRW
tRecovery
WR+CS
tAH tAV A[x:0] Valid Address tDHW tDV Write D[7:0] Valid Data
Note: RD should be tied to high
Figure-37 Non_multiplexed Intel Write Timing
77
OCTAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL TEMPERATURE RANGES
ORDERING INFORMATION
IDT XXXXXXX Device Type XX X Process/ Temperature Range
Blank
Industrial (-40 C to +85 C)
DR BB
Plastic Quad Flatpack (PQFP, DR208) Plastic Ball Grid Array (PBGA, BB208)
82V2088
Long Haul/Short Haul LIU
DATASHEET DOCUMENT HISTORY
06/26/2003 pgs. 18, 19, 30, 31, 35, 43, 61, 62.
CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054
for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com*
for Tech Support: 408-330-1753 email:TELECOMhelp@idt.com
To search for sales office near you, please click the sales button found on our home page or dial the 800# above and press 2. The IDT logo is a registered trademark of Integrated Device Technology, Inc.
78


▲Up To Search▲   

 
Price & Availability of IDT82V2088

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X