View DS1810_183150.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DS1810 5V EconoReset with Push-Pull Output
www.dalsemi.com
FEATURES
Automatically restarts a microprocessor after power failure Maintains reset for 150 ms after VCC returns to an in-tolerance condition Reduces need for discrete components Precision temperature-compensated voltage reference and voltage sensor Low-cost TO-92 or space saving surface mount SOT-23 packages available Push-Pull output for low current operation Operating temperature -40C to +85C
PIN ASSIGNMENT
3
1 2 SOT-23 PACKAGE
123
123 TO-92 PACKAGE See Mech. Drawings Section
PIN DESCRIPTION TO-92
1 2 3
RST
VCC GND
Active Low Reset Output Power Supply Ground
SOT-23
1 2 3
RST
VCC GND
Active Low Reset Output Power Supply Ground
DESCRIPTION
The DS1810 EconoReset uses a precision temperature reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to an in-tolerance condition, the reset signal is kept in the active state for approximately 150 ms to allow the power supply and processor to stabilize.
1 of 5
111999
DS1810
OPERATION - POWER MONITOR
The DS1810 provides the function of detecting out-of-tolerance power supply conditions and warning a processor-based system of impending power failure. When VCC is detected as out-of-tolerance, the RST signal is asserted. On power-up, RST is kept active for approximately 150 ms after the power supply has reached the selected tolerance. This allows the power supply and microprocessor to stabilize before RST is released.
BLOCK DIAGRAM (PUSH-PULL OUTPUT) Figure 1
APPLICATION EXAMPLE Figure 2
OUTPUT VALID CONDITIONS
All versions of the DS1810 can maintain a valid output as long as VCC remains above 1.2 volt. However, the RST outputs on the DS1810 use a push-pull structure which can maintain a valid output below 1.2 volts on an input. To sink current below 1.2 volts, a resistor can be connected from RST to Ground (see Figure 3). This arrangement will maintain a valid value on the RST outputs even it VCC approaches 0 volts. During both power-up and -down this arrangement will draw current when RST is in the high state. A value of about 100 k should be adequate to maintain a valid condition.
2 of 5
DS1810
APPLICATION DIAGRAM: RST VALID TO 0 VOLTS VCC ON THE DS1810 Figure 3
TIMING DIAGRAM: POWER-UP Figure 4
TIMING DIAGRAM: POWER-DOWN Figure 5
3 of 5
DS1810
ABSOLUTE MAXIMUM RATINGS*
Voltage on VCC Pin Relative to Ground Voltage on RST Relative to Ground Operating Temperature Storage Temperature Soldering Temperature * -0.5V to +7.0V -0.5V to VCC +0.5V -40C to +85C -55C to +125C 260C for 10 seconds
This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS
PARAMETER Supply Voltage SYMBOL VCC MIN 1.2 TYP MAX 5.5
(-40C to +85C)
UNITS V NOTES 1
DC ELECTRICAL CHARACTERISTICS
PARAMETER Output Voltage @ 0-500 A Output Current @ 2.4V Output Current @ 0.4V Operating Current VCC < 5.5 VCC Trip Point (DS1810-5) VCC Trip Point (DS1810-10) VCC Trip Point (DS1810-15) Output Capacitance SYMBOL VOH IOH IOL ICC VCCTP VCCTP VCCTP COUT 4.50 4.25 4.00 +10 MIN
(-40C to +85C; VCC=1.2V to 5.5V)
TYP 350 30 4.62 4.37 4.12 40 4.75 4.49 4.24 10 MAX UNITS V A mA A V V V pF NOTES 1 2 2 3 1 1 1
VCC-0.5V VCC-0.1V
AC ELECTRICAL CHARACTERISTICS
PARAMETER RESET Active Time VCC Detect to RST VCC Slew Rate (VCCTP (MAX) to VCCTP (MIN)) VCC Slew Rate (VCCTP (MIN) to VCCTP (MAX)) VCC Detect to RST SYMBOL tRST tRPD tF tR tRPU 300 0 100 MIN 100
(-40C to +85C; VCC=1.2V to 5.5V)
TYP 150 2 MAX 300 5 UNITS ms s s ns 150 300 ms 4 NOTES
4 of 5
DS1810
NOTES:
1. All voltages are referenced to ground. 2. Measured with VCC 2.7 volts. 3. Measured with RST output open. 4. tR = 5 s.
PART MARKING CODES
SOT-23 PACKAGE
"A", "B", &"C" represent the device type. 810 DS1810 811 DS1811 812 DS1812 813 DS1813 815 DS1815 816 DS1816 817 DS1817 818 DS1818
"D" represents the device tolerance. A 5% B 10% C 15% D 20%
5 of 5

▲Up To Search▲

Price & Availability of DS1810

	To Download DS1810 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .