Part Number Hot Search : 
SSI3522 WSBM8518 EM871 BZX79 V7477Z QS3390 H5PS1G SFW9624
Product Description
Full Text Search
 

To Download M655P1555200MHZ Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 Integrated Circuit Systems
M655 Series
Voltage Controlled SAW Oscillators
M655 Series
Performance Specifications
DESCRIPTION
The M655 Series of Voltage Controlled SAW Oscillators is a low cost solution for many Telecom applications. An internal SAW filter provides jitter performance of less than 0.5psec (rms).
9mm
14mm
FEATURES
This device is specified for an operating temperature range of -40C to +85C. A disable feature forces the output into a static condition by applying a logic "0" to the clock enable input. The oscillator is housed in a hermetically-sealed, leadless surface mount package. The M655 Series of VCOs is available over an output frequency range of 155MHz to 900MHz. The device is most suited for phase-locked loop applications as well as clock and data recovery circuits.
Output Frequencies at 155MHz to 900MHz Low Phase Jitter, 0.5psec (rms) typical 3.3 Volt Supply Operation Complementary Outputs Output Disable Feature LCC Surface Mount Package (9 x 14mm)
APPLICATION
ABSOLUTE MAX RATINGS Operating Temp. Range (Case): ........................ -40C to +85C Storage Temp. Range (Ambient): .................... -55C to +125C Control Voltage Range: ................................................. 0 to VCC Output Current: ................................................................ 20 mA Power Supply Voltage (Vcc): ................................ 0 to +3.6 Vdc
Clock Smoothing for OC192/OC48/ OC12/OC3 Clock Smoothing for STS96/STS48/ STS12/STS3/STS1 Frequency Translation Clock and Data Retiming
ISO 9001 Registered
Integrated Circuit Systems, Inc.
Communications Modules
1
www.icst.com/Comm-Modules
tel: 508-852-5400
Integrated Circuit Systems
SPECIFICATIONS
M655 Series
Performance Specifications
Specifications @ Vcc = +3.3 Volts, Vee = 0 Volts, and Ta = +25C unless otherwise specified PARAMETER Output Frequency Absolute Pull Range Frequency Stability (-40C to 85C) Duty Cycle Spurious Suppression-50 Linearity Logic Levels Vol1 Voh2 Input Control Voltage (Vc) Range VCO Gain Vc Input Impedance Vc Modulation BW Clock/Output Enable (Pin 2) Clock/Output Disable (Pin 2) Output Rise Time Output Fall Time Jitter @ 155.520MHz offset from carrier 12kHz to 20MHz Jitter @ 622.080MHz offset from carrier 12kHz to 80MHz Phase Noise (offset from carrier) 100Hz 1kHz 10kHz 100kHz Operating Temperature Supply Current Icc Supply Voltage Vcc
Min Typ Max Units
155 50 +25/-150 45 -60 6 Vcc - 1.95 Vcc - 0.98 0 200 8 500 2.0 -0.3 250 250 0.230 0.458 -65 -95 -120 -140 25 80 3.3
900
55 dBc Vcc - 1.63 Vcc - 0.75 Vcc 12 Vcc +0.3 0.8 400 400
MHz ppm ppm % % Volts Volts Volts ppm/V K kHz Volts Volts psec psec psec rms psec rms dBc/Hz dBc/Hz dBc/Hz dBc/Hz C mA V
-40 3.2
+85 95 3.4
Notes: 1. Output levels are standard 10K ECL and are fully 100K ECL compatible. 2. Transition times are measured from 20% to 80% of a full 10K ECL level swing.
Phase Noise
-90 -100 -110
SSB Phase Noise dBc/Hz
-120 -130 -140 -150 -160 -170 1E+03
1E+04
1E+05 Frequency in Hz
1E+0
Integrated Circuit Systems, Inc.
Communications Modules
2
www.icst.com/Comm-Modules
tel: 508-852-5400
Integrated Circuit Systems
SPECIFICATIONS Jitter
M655 Series
Performance Specifications
Output
Typical Linearity
622310000 622280000 622250000 622220000 622190000 622160000 622130000 622100000 622070000
Typical Frequency Pushing
10
5
Deviation (PPM)
0 PPM Deviation -5
-10
622040000 622010000 621980000 0.2 0.4 0.6 08 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2
-15 3.15
Typical linearity of a M655 operating at 622.08 MHz over the input range of .3 to 3.0 volts
3.2
3.25
3.3 Vcc (V)
3.35
3.4
3.45
Integrated Circuit Systems, Inc.
Communications Modules
3
www.icst.com/Comm-Modules
tel: 508-852-5400
Integrated Circuit Systems
IR REFLOW PROFILE
M655 Series
Performance Specifications
IR Reflow Profile
(Vendor Recommendation) 220
Temperature (C)
180 150
100
50
Micro Networks has subjected their VCSO component to various reflow profiles and test conditions for optimum substrate mounting performance. The conditions suggested here are recommended temperature settings for the VCSO device during the reflow processes. The best case condition for the device is a slow ramp up to prevent thermal shock before reaching reflow temperatures of Sn/Pb flux activated solder with a melting point of 183 degree Celsius. The M655 device should not see temperatures above 183 degrees Celsius for an extended periods beyond 60 seconds. Maximum peak temperature for the device should not exceed 220 degrees Celsius for longer then 20 seconds.
105-150
60
60-90 Time (seconds)
Micro Networks has designed the M655 device as a sealed unit. The package is 100% tested for seal defects. Aqueous, solvent, or other wash type cleaning methods is acceptable for this device.
TAPE & REEL
G
J
C B A
D F N I L
M
E O K H
TAPE & REEL DIMENSIONS TAPE A B C D E M N O MM REEL MM 24 F 1.78 11.5 G 21 1.5 H 13 4 I 100 12 J 5 9.2 K 25 14.5 L 330 3.7 No. per Reel: 300 Max Communications Modules
4
Integrated Circuit Systems, Inc.
www.icst.com/Comm-Modules
tel: 508-852-5400
Integrated Circuit Systems
APPLICATIONS
M655 Series
Performance Specifications
Jitter Attenuator
155.52MHz and Frequency Detector Loop Filter M655 155.520MHz 155.52MHz
Frequency Translator
19.44MHz and Frequency Detector Loop Filter Divide by 32 M655 622.080MHz 622.080MHz
Multi-rate FEC Clock Generator
M655 622.080MHz Fin and Frequency Detector Loop Filter M655 666.514MHz M655 669.13MHz Programmable Divider Fout MUX
Integrated Circuit Systems, Inc.
Communications Modules
5
www.icst.com/Comm-Modules
tel: 508-852-5400
Integrated Circuit Systems
MECHANICAL DIMENSIONS & PIN CONFIGURATION
.145 [3.28] MAX
M655 Series
Performance Specifications
.550 [13.97] 6 5 4
Pin No. 1 2 3 4 5 6
Function Vt CE GND Cout nCout Vcc
2 1 ORIENTATION KEY 1
3
8X .040 [1.02] 3 2
6 .100 [2.54]
4
.200 [5.08]
ORDERING INFORMATION
Part Number M655P 622.0800
.350 [8.89]
8X .066 [1.68]
BLOCK DIAGRAM
Vcc
P for PECL Operation Specify frequency in MHz xxx.xxxx (eg. 155.5200MHz, 311.0400MHz, 622.0800MHz, 666.5140MHz) Absolute Pull Range Blank = 50ppm 100ppm available for certain frequencies. Consult factory.
6 Control Voltage Clock Enable 1 2 M655 Series 4 5 50 3 GND Vt = Vcc-2V 50 Output Output
Vt
ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate.
Integrated Circuit Systems, Inc.
Communications Modules 324 Clark Street Worcester, MA 01606 tel: 508-852-5400 fax: 508-852-8456
European Sales Headquarters Hertogsingel 20 6214 AD Maastricht The Netherlands tel: +31-43-32-70912 fax: +31-43-32-70715 Integrated Circuit Systems, Inc.
www.icst.com/Comm-Modules Communications Modules www.icst.com/Comm-Modules
6
tel: 508-852-5400
Rev. 9.0


▲Up To Search▲   

 
Price & Availability of M655P1555200MHZ

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X