View AN3672NFBP_163528.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ICs for VCR
AN3672NFBP
Audio signal processor IC for HiFi VCR incorporating EIAJ sound multiplex system
Unit: mm
s Overview
The AN3672NFBP is a HiFi audio signal processor IC (NTSC) incorporating EIAJ sound multiplex decoder and pre/recording amplifier. An adjustment-free sound multiplex decoder is realized through both of fO automatic adjustment of high precision VCO by a reference signal (fSC) and an SIF (4.5 MHz inter-carrier sound intermediate frequency) signal input.
48 49
17.20.4 14.00.3 33 32 (1.00) 17 1.30.1 2.850.20 1 (1.00) 16 0.80 0.35 +0.10 - 0.05 14.00.3 17.20.4 64
(1.60)
+0.10 0.20 - 0.05
s Features
* Built-in EIAJ sound multiplex decoder * Full adjustment-free by SIF signal input * fO automatic adjustment of high precision VCO * Built-in pre/recording amplifier
0.10 Seating plane
QFH064-P-1414A
s Applications
* HiFi VCR
1.30.1 0.10.1
0 to 10 (0.80)
1
2
Main REF Mute CTL Rec. AGC adj. GND1 (R) PE VCC1 (5 V) N.R. REF (R) Logic GND I2C clock I2C data Logic VCC REG fSC MTS mute CTL (H1 = Mute on) N.R. det. 1 (R) N.R. det. 2 (R) 37 38 39 40 41 42 43 44 45 46 36 35 34 33 32
Logic S/H SW noise SW21 PNR R-ch. SW9 Audio limit R-ch. VCO SW12 ZZ-PROM Mute VCO-fO CTL adj. Logic 952 Hz BPF COMP INSW mute
AN3672NFBP
s Block Diagram
SIF / base band in
Rec. PB
SW31 PC Matrix SW19 Amp. Normal Normal Mix. HiFi BS PC Audio limit SW4 SW noise PNR R-ch. SW30 R Input SW (L) L Input SW (R) VREF1 R S/H PB LPF SW10 SW14 Det. Mix. SW13 Rec.LPF L-ch. VCO AGC L-ch.BPF Cut amp. HA2 SW16 From pin 3 FM lim. Mix. HOLD timing H SW11 L HiFi R-ch.BPF Mute R SW18 BS Liner SW From pin 1 Noise det. PB LPF HPF Rec.LPF
DEM REF
48
47
Sub-level det.
49
DEM block
Main out
50
MTS VCC (5 V)
51
4.5fH trap
CUE BPF
AM demod.
DC out
52
Sub BPF
Sub det.
3.5fH VCO
Logic
Main deem
FM demod.
Sub deem
CCA out (R) 31 Noise det./ Rec. AGC det. 30 FM in 29 HA out (fO / BPF monitor) 28 Forced normal (Normal = L) common use for ENV-det. output 27 Audio FF input 26 Rec. DC2 25 P/R VCC 24 SW15 HA1 HEAD1 23
Line out (R)
L Mute SW17 L R L Amp.
53
LOG amp.
Amp.
54
Output SW LR
P/R GND
55
22
HEAD2 21
GND2 LED PORT 56 (Multi-value output) 57 Line out (L) 58 VCC2 (12 V) 59 RFC AGC out
RFC SW2 Det. INSW mute L SW22 Mix.
COMMON 20
RFC AGC det.
60
Rec. DC1 19 18 17
Normal out
61
Normal in
62
CCA out (L) N.R. REF (L) N.R. det. 2 (L) 13 14 Ext.1-IN (L) 16 N.R. det. 1 (L) 15 Ext.2-IN (L) Sound multiplex output L
Comp.
63
Sub REF
64
12 11 10 9 8 7 6
5 4 3 2 1
CUE det. Ext.3-IN (L) BS-IN (L) Ext.3-IN (R) BS-IN (R)
IN-REF (L) GND1 (L) Ext.2-IN (R) Ext.1-IN (R) Sound multiplex output R IN-REF (R) VREF
ICs for VCR
ICs for VCR
s Pin Descriptions
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 BS-IN (R) Ext.3-IN (R) BS-IN (L) Ext.3-IN (L) CUE det. 1/2 VCC1-VREF IN-REF (R) Sound multiplex output R Ext.1-IN (R) Ext.2-IN (R) GND1 (L) IN-REF (L) Sound multiplex output L Ext.1-IN (L) Ext.2-IN (L) N.R. det. 1 (L-channel: Weighting) N.R. det. 2 (L-channel) N.R. REF (L-channel) CCA out (L) (+) Rec. amp. DCFB pin (+) Rec. amp. output and PB common pin (-) Rec. amp. output and PB-channel 2 input pin 23 24 Pre/rec.-GND (-) Rec. amp. output and PB-channel 1 input pin 25 26 27 28 29 Pre/rec.-VCC (-) Recording amplifier DCFB pin Head switching pulse input for FM audio Envelope detector and forced normal output Pre-amp. output / monitor output Rec.-mute CTL pin 30 31 Playback FM input Normal identification noise detection and rec.-AGC det. pin 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Description Pin No. 32 33 34 35 36 37 38 39 40 41 42 43 44 45 CCA out (R)
AN3672NFBP
Description
N.R. REF (R-channel) N.R. det. 2 (R-channel) N.R. det. 1 (R-channel: Weighting) Mute-CTL pin Rec.-AGC adj. pin GND1 (R) PE pin VCC (VCC1 = 5 V) Logic-GND Serial clock input Serial data input Logic-REG pin Reference signal input pin for fO automatic adjustment Sound multiplex mute-CTL pin Main REF DEM REF SIF / base band input Sub level det. Main out MTS VCC (typ. = 5 V) DC out Line out (R-channel) N.C. GND2 LED PORT Line out (L-channel) VCC2 (typ. = 12 V) RFC out RFC-AGC det. Normal out Normal in Comp. Sub REF
3
AN3672NFBP
s Absolute Maximum Ratings
Parameter Supply voltage
*1, 2 *1
ICs for VCR
Symbol VCC1 VCC2
Rating 5.5 13.0 798 -20 to +75 -55 to +150
Unit V
Power dissipation
PD Topr Tstg
mW C C
Operating ambient temperature Storage temperature
*1
Note) 1. The reverse insertion of this IC will cause its breakdown. 2. Use this IC paying attention to its surge breakdown. (Refer to "s Usage Note" in detail.) 3. *1: Except for the power dissipation, operating ambient temperature and storage temperature, all ratings are for Ta = 25C. *2: The power dissipation shown is the value for Ta = 75C. (Refer to "s Application Notes" in detail.)
s Recommended Operating Range
Parameter Supply voltage Symbol VCC1 VCC2 Range 4.5 to 5.3 8.0 to 12.5 Unit V
s Electrical Characteristics at VCC1 = 5 V, VCC2 = 12 V, Ta = 25C
Parameter Circuit current (5 V) at recording Circuit current (12 V) at recording Circuit current (5 V) at playback Circuit current (12 V) at playback ENC out level 1-L ENC out level 1-R ENC out level 3-L ENC out level 3-R Normal recording out level Line out level L Gain = mode (0) Line out level R Gain = mode (0) Line out THD L Line out THD R Line out VO-max L Line out VO-max R 4 Symbol ICCR1 ICCR2 ICCP1 ICCP2 VHRO1L VHRO1R VHRO3L VHRO3R VNRO VG2L VG2R THRML THRMR VMLOL VMLOR Conditions Recording mode Measurement after adjusting fO Recording mode Measurement after adjusting fO Playback mode Measurement after adjusting fO Playback mode Measurement after adjusting fO Min 104 5 70 5 Typ 130 9 95 9 -9.5 -9.5 -30 -30 Max 156 13 120 13 -7.5 -7.5 -27 -27 Unit mA mA mA mA dBS dBS dB dB dBS dBS dBS % % dBS dBS
VIN = -26.8 dBS, 1 kHz, DIN audio -11.5 VIN = -26.8 dBS, 1 kHz, DIN audio -11.5 VIN = -86.8 dBS, 1 kHz DIN audio, VHRO3L /VHRO1L VIN = -86.8 dBS, 1 kHz DIN audio, VHRO3R /VHRO1R VIN = -26.8 dBS, 1 kHz Gain = High VIN = -26.8 dBS, 1 kHz Gain = High VIN = -26.8 dBS, 1 kHz VIN = -26.8 dBS, 1 kHz fIN = 1 kHz, at output THD 3% fIN = 1 kHz, at output THD 3% -33 -33
VIN = -26.8 dBS, 1 kHz, Normal out -21.5 -20.0 -18.5 -7.5 -7.5 8.2 8.2 -6.0 -6.0 0.05 0.05 10.5 10.5 -4.5 -4.5 0.1 0.1
ICs for VCR
s Electrical Characteristics at VCC1 = 5 V, VCC2 = 12 V, Ta = 25C (continued)
Parameter ENC out VO-max L ENC out VO-max R RF conv. out level Line out S/N L Line out S/N R Crosstalk between inputs 1 (Select the sound multiplex)
*1
AN3672NFBP
Symbol VMFEL VMFER VRFC NHLOL NHLOR CTIT CTIE1
Conditions fIN = 1 kHz, at output THD 3% fIN = 1 kHz, at output THD 3% VIN = -26.8 dBS, 1 kHz BS monitor mode RG = 6.8 k, DIN audio RG = 6.8 k, DIN audio Ext.1 Ext.3 in = -16.8 dBS 1 kHz, DIN audio Sound multiplex Ext.2 Ext.3 in = -16.8 dBS 1 kHz, DIN audio Sound multiplex Ext.1, Ext.3 in = -16.8 dBS 1 kHz, DIN audio Sound multiplex Ext.1, Ext.2 in = -16.8 dBS 1 kHz, DIN audio Ext.1 in R-ch. = -16.8 dBS, 1 kHz DIN audio Ext.1 in L-ch. = -16.8 dBS, 1 kHz DIN audio HiFi, BS in = -16.8 dBS 1 kHz, DIN audio HiFi, BS in = -16.8 dBS 1 kHz, DIN audio HiFi, NOR in = -16.8 dBS 1 kHz, DIN audio Ext.1 in R-ch. = -16.8 dBS, 1 kHz DIN audio Ext.1 in L-ch. = -16.8 dBS, 1 kHz DIN audio TV in = -16.8 dBS, 1 kHz, Gain = 1 DIN audio TV in = -16.8 dBS, 1 kHz, Gain = 1 DIN audio NTSC mode, non-modulation, after adjustment NTSC mode, non-modulation, after adjustment NTSC mode, mode = (0, 1)
Min -4 -4 -8 75 75
Typ 0.3 0.3 -5 80 80 -60 -75
Max -2 -55 -65
Unit dBS dBS dBS dB dB dB dB
Crosstalk between inputs 2 *1 (Ext.1-IN select) Crosstalk between inputs 3 *1 (Ext.2-IN select) Crosstalk between inputs 4 *1 (Ext.3-IN select) Crosstalk between channels RL *1 Crosstalk between channels LR *1 Crosstalk between output mode 1 *1 (Normal select) Crosstalk between output mode 2 *1 (HiFi select) Crosstalk between output mode 3 *1 (BS monitor mode) Crosstalk between ENC out channels (RL) Crosstalk between ENC out channels (LR) Output muting ratio L *1 Output muting ratio R *1 VCO output frequency L (NTSC) VCO output frequency R (NTSC) VCO output L/R mix. ratio L
CTIE2
-75
-65
dB
CTIE3
-75
-65
dB
CTTRL CTTLR CTHN CTNH CTNH CTENRL CTENLR MuteL MuteR fNL fNR FNLN

-80 -80 -75 -75 -60 -40 -40 -60 -60
-65 -65 -60 -60 -55 -30 -30 -45 -45
dB dB dB dB dB dB dB dB dB kHz kHz dB
1 292 1 300 1 308 1 692 1 700 1 708 8.5 10 11.5
Note) *1: 10 dB should be reduced from the calculation result because of +10 dB increased input.
5
AN3672NFBP
s Electrical Characteristics at VCC1 = 5 V, VCC2 = 12 V, Ta = 25C (continued)
Parameter FM deviation L FM deviation R FM deviation L/R ratio FM modulation distortion L FM modulation distortion R FM modulation S/N L FM modulation S/N R 1.3 MHz BPF frequency characteristics 1 *2 1.3 MHz BPF frequency characteristics 2 *2 1.3 MHz BPF frequency characteristics 3 *2 1.3 MHz BPF frequency characteristics 5 *2 1.7 MHz BPF frequency characteristics 1 *2 1.7 MHz BPF frequency characteristics 2 *2 1.7 MHz BPF frequency characteristics 3 *2 PB out level 1-L *2 PB out level 1-R
*2
ICs for VCR
Symbol DEVL DEVR DEVLR THFEL THFER NHFEL NHFER BPF11 BPF12 BPF13 BPF15 BPF21 BPF22 BPF23 VHPO1L VHPO1R BHP VHPO3L VHPO3R NHPOL NHPOR
Conditions VIN = -26.8 dBS, 1 kHz VIN = -26.8 dBS, 1 kHz DEVR - DEVL VIN = -26.8 dBS, 1 kHz, FM RF out VIN = -26.8 dBS, 1 kHz, FM RF out RG = 6.8 k, DIN audio, FM RF out RG = 6.8 k, DIN audio, FM RF out BPF monitor (L-ch.), fC = 1.3 MHz fC = 1.45 MHz fC = 1.15 MHz V(1.05M) / V(1.45M) BPF monitor (R-ch.), NTSC mode fC = 1.7 MHz fC = 1.85 MHz fC = 1.55 MHz
Min 44 44 -6 33 33 70 -10.0 -4.0 -13 70 -6.0 -7.0
Typ 50 50 0 0.5 0.5 40 40 140 -5.0 - 0.5 -1.5 140 0 -1.6 -6.0 -6.0 0 -60 -60 80 80 0.2 0.2 -80 -80 15 1.5
Max 56 56 6 1.0 1.0
Unit kHz kHz kHz % % dB dB
210 mV[p-p] 2.0 3.0 7.0 dB dB dB
210 mV[p-p] 3.5 3.0 -4.5 -4.5 1.5 -54 -54 0.8 0.8 -65 -65 30 6.0 dB dB dBS dBS dB dB dB dB dB % % dB dB mV[p-p] dB
VIN = 50 kHz Dev., 1 kHz, Line out -7.5 VIN = 50 kHz Dev., 1 kHz, Line out -7.5 -1.5 FMIN = 50 kHz -30 dB, DIN audio FMIN = 50 kHz -30 dB, DIN audio Non-modulation, Line out, DIN audio Non-modulation, Line out, DIN audio In: Dev = 100 kHz, f = 1 kHz Line out In: Dev = 100 kHz, f = 1 kHz Line out VIN = 50 kHz Dev, 1 kHz DIN audio VIN = 50 kHz Dev, 1 kHz DIN audio fCL = 1.3 MHz fCR = 1.7 MHz 50 kHz Dev. fCL = 1.3 MHz fCR = 1.7 MHz 50 kHz Dev. -66 -66 75 75 7 0.1
PB out level L/R ratio PB out level 3-L PB out level 3-R PB out S/N L PB out S/N R
*2 *2 *2 *2 *2
PB out distortion L
THPOL THPOR CTPRL CTPLR DOC1 DOC2
PB out distortion R *2 Crosstalk between PB out channels (RL) *2 Crosstalk between PB out channels (LR) *2 DOC on level DOC hysteresis
Note) *2: PB-FM input level: Single 140 mV[p-p], Mix. 280 mV[p-p]
6
ICs for VCR
s Electrical Characteristics at VCC1 = 5 V, VCC2 = 12 V, Ta = 25C (continued)
Parameter Forced normal on level 1 PB-ch.1 gain PB-ch.2 gain Gain ratio between PB-channels PB-ch.1 input referred noise PB-ch.2 input referred noise Rec. output level (1.3 MHz component) Rec. output level (1.7 MHz component) Rec. output 2nd harmonic distortion (2.6 MHz/1.3 MHz component ratio) Rec. output 2nd harmonic distortion (3.4 MHz/1.7 MHz component ratio)
*2
AN3672NFBP
Symbol ND1 G2429 G2229 G2422 N2429 N2229 I24L I24R I2fL I2fR
Conditions f = 150 kHz, ND mode = 0, 0 f = 1.5 MHz, 0.2 mV[p-p], AFF = High f = 1.5 MHz, 0.2 mV[p-p], AFF = Low Calculates the G2429 - G2229 Divide by gain after measuring noise level with 1 MHz BPF Divide by gain after measuring noise level with 1 MHz BPF Measure the 1.3 MHz component of current output, (Radj = 33k), NOR Measure the 1.7 MHz component of current output, (Radj = 33k), NOR Measure the 2.6 MHz/1.3 MHz component of current output Measure the 3.4 MHz/1.3 MHz component of current output
Min 30 70 70 -3 6 21
Typ 75 76 76 0 0.7 0.7 9 27 -40 -40
Max 120 82 82 3
Unit kHz Dev dB dB dB
1.2 V[rms] 1.2 V[rms] 12 33 -35 -35 mA[p-p] mA[p-p] dB dB
Television sound multiplex demodulation block Note) Input level at 100% modulation Mono, L+R: 106 mV[rms] ( = 0.3 V[p-p]) Sub (L-R) carrier: 63.6 mV[rms] (BIL), 84.8 mV[rms] (Stereo) Unless otherwise specified, pre-emphasis = off Mono output level Mono frequency characteristics (10 kHz) Mono distortion Mono S/N Channel balance Sub output level Sub frequency characteristics (10 kHz) Sub distortion Sub S/N Sub detection sensitivity Stereo output level V0(Mon) V1(Mon) f = 1 kHz, Mono, 100% modulation, -5.7 15 kHz LPF f = 1 kHz, Mono, 100% modulation, -18 15 kHz LPF 60 -1 -5.7 -20 54 -9 -5.7 -3.7 -14 0.3 67 0 -3.7 -16 1 60 -4.3 -3.7 -1.7 -10 1 1 -1.7 -12 2 -3 -1.7 dBS dB % dB dB dBS dB % dB dB dBS
THD(Mon) f = 1 kHz, Mono, 100% modulation, 15 kHz LPF S/N(Mon) Non-signal, 15 kHz LPF CB(Mon) V0(Sub) V1(Sub) f = 1 kHz, Mono, 100% modulation, 15 kHz LPF f = 1 kHz, BIL, 100% modulation, 15 kHz LPF f = 1 kHz, BIL, 100% modulation, 15 kHz LPF
THD(Sub) f = 1 kHz, BIL, 100% modulation, 15 kHz LPF S/N(Sub) SD V1(st) Sub carrier + Cue (BIL), 15 kHz LPF Sub carrier + Cue (BIL) f = 1 kHz, Stereo, 100% modulation, 15 kHz LPF
Note) *2: PB-FM input level: Single 140 mV[p-p], Mix. 280 mV[p-p] (30-pin)
7
AN3672NFBP
s Electrical Characteristics at VCC1 = 5 V, VCC2 = 12 V, Ta = 25C (continued)
Parameter Symbol Conditions f = 1 kHz (L-only), 100% modulation, 15 kHz LPF f = 1 kHz (R-only), 100% modulation, 15 kHz LPF f = 1 kHz (Stereo), 100% modulation Sub carrier + Cue (Stereo) 15 kHz LPF Sub carrier + Cue (BIL) f = 1 kHz (BIL main), 100% modulation, 15 kHz LPF f = 1 kHz (BIL sub), 100% modulation, 15 kHz LPF f = 1 kHz (BIL), 100% modulation f = 1 kHz (BIL), 100% modulation Non-signal Sub carrier signal, + Cue signal (Stereo) Sub carrier signal + Cue signal (BIL) Main Sub carrier signal + Cue signal (BIL) Sub f = 1 kHz (Mono), 100% modulation f = 1 kHz (Stereo), 100% modulation f = 1 kHz (BIL), 100% modulation f = 1 kHz (BIL), 100% modulation Non-signal Sub carrier signal, + Cue signal (Stereo) Sub carrier signal, + Cue signal (BIL) f = 440 Hz (Mono), 40% modulation f = 440 Hz (Mono), 10% modulation Vi (SIF) = 90 dBV, fm = 1 kHz Mono, 100% modulation, ratio to VO of base band Vi (SIF) = 90 dBV, fm = 1 kHz, 100% modulation Min Typ
ICs for VCR
Max 2 -4 20 30 100 100 100 100 0.4 1.9 4 1
Unit
Television sound multiplex demodulation block (continued) Stereo separation 1 Stereo separation 2 Stereo distortion Stereo S/N CUE detection sensitivity Crosstalk (MainSub) Crosstalk (SubMain) Residual carrier (Main) Residual carrier (Sub) DC offset (Monaural) DC offset (Stereo) DC offset (Main) DC offset (Sub) Mute attenuation amount (Monaural) Mute attenuation amount (Stereo) Mute attenuation amount (Main) Mute attenuation amount (Sub) LED-PORT voltage 1 (Mono) LED-PORT voltage 2 (Stereo) LED-PORT voltage 3 (BIL) LOG amp. output 1 LOG amp. output 2 SIF detection block Output ratio of SIF to base band VOSIF - 0.5 0 0.5 dB Sepr Sepl THD(st) Vn(st) CD CTMS CTSM LCM LCS OMO OST OMA OSB MMO MST MMA MSB LED1 LED2 LED3 VLOG1 VLOG2 30 30 54 -11 54 54 65 65 65 65 0 1.3 2.7 4 43 43 0.3 60 -6.6 60 60 10 15 20 20 20 20 80 80 80 80 0.1 1.6 3.1 dB dB % dB dB dB dB mV[rms] mV[rms] mV mV mV mV dB dB dB dB V V V V V
SIF total harmonic distortion
THDSIF
0.3
1.0
%
8
ICs for VCR
s Electrical Characteristics at VCC1 = 5 V, VCC2 = 12 V, Ta = 25C (continued)
* Design reference data
AN3672NFBP
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter Data input (high-level) Data input (low-level) Clock input (high-level) Clock input (low-level) Mute CTL input (high-level) Mute CTL input (low-level) Forced normal on level 2 RF conv. AGC level Normal rec. THD Normal input crosstalk 1 (Line in R select) Normal input crosstalk 2 (Line in L select) Carrier 3rd harmonics L Carrier 3rd harmonics R 1.3 MHz BPF frequency characteristics 4 1.3 MHz BPF frequency characteristics 6 1.7 MHz BPF frequency characteristics 4 1.7 MHz BPF frequency characteristics 5 1.7 MHz BPF frequency characteristics 6 BPF group delay difference (fO 100 kHz) VCO fO temperature dependency Normal off delay time ENC attack time ENC recovery time HOLD pulse width ENV out 1 ENV out 2 HiFi rec. PB crosstalk
Symbol VHDATA VLDATA VHCLOC VLCLOC VIHMUT VILMUT ND2
Conditions At VCC = 5 V At VCC = 5 V At VCC = 5 V At VCC = 5 V Mute on Mute off f = 150 kHz, Mode 01 Dev.
Min 2.25 0 2.25 0 3.5 0
Typ 60 1.0 0.02 -75 -75 -50 -50 -32 -15 -13 -26 -8 500 5 3 4 65 10 1.3 2.2 -79
Max 5 0.75 5 0.75 5 1.5
Unit V V V V V V kHz Dev dBS % dB dB dB dB dB dB dB dB dB ns kHz FF ms ms s V V dB
VRFCAG VIN = -16.8 dBS, f = 1 kHz TNRO CTNRR CTNLL 3HDL 3HDR BPF14 BPF16 BPF24 BPF25 BPF26 GDBPF TVCO MON ENAT ENRT HPUL ENV1 ENV2 CTRP VIN = -26.8 dBS, f = 1 kHz Ext.1 in L = -16.8 dBS DIN audio Ext.1 in R = -16.8 dBS DIN audio RF recording out RF recording out 1.7 MHz / 1.3 MHz 1.55 MHz / 1.15 MHz 2.1 MHz / 1.7 MHz 1.3 MHz / 1.7 MHz 1.45 MHz / 1385 MHz Difference of fO 100 kHz fO (T = -10C) - fO (T = 75C) Define with FF timing f = 5 kHz, VIN = typ.-20 dB f = 5 kHz, VIN = typ.-20 dB Test mode, PB 1.3 MHz + 1.7 MHz mix. 70 mV[p-p] x 2 1.3 MHz + 1.7 MHz mix. 280 mV[p-p] x 2 PB, VIN = -16.8 dBS, 1 kHz
9
AN3672NFBP
s Terminal Equivalent Circuits (continued)
Pin No. 1 Equivalent circuit Pin40 (VCC1) 6.8 k 6.8 k Description
ICs for VCR
Voltage (typ.) 2.5 V
BS-IN (R-channel): BS monitor-exclusive input pin Typical input level is 1 kHz, -26.8 dBS.
1 400 k To VREF 2
Pin40 (VCC1)
6.8 k Ext.3-IN (R-channel): Typical input level is 1 kHz, -26.8 dBS. 0V
6.8 k
6.8 k
2
600 59 k
3 4 5
Refer to pin 1 Refer to pin 2
Pin40 (VCC1) 5.1 k
BS-IN (L-channel) Ext.3-IN (L-channel) Cancel of DC offset for Cue signal
2.5 V 0V 2.5 V
5
600 4 k 1 k
3.06 k 5.1 k 5.1 k
6
Pin40 (VCC1) 50 k 200 50 k 40 k 200 60 k
VREF
2.5 V
6
10
ICs for VCR
s Terminal Equivalent Circuits (continued)
Pin No. 7 Equivalent circuit Pin40 (VCC1) 600 5.6 k 5 k Description IN-REF (R-channel):
AN3672NFBP
Voltage (typ.) 2.05 V
7
1.5 k
425 8
425
850 Sound multiplex output R: Tuner output pin 2.5 V
Pin51 (MTS VCC) 2 k 1 k
8
9 10 11 12 13 14 15 16
Refer to pin 2 Refer to pin 2 Refer to pin 7 Refer to pin 8 Refer to pin 2 Refer to pin 2
Ext.1-IN (R-channel) Ext.2-IN (R-channel) GND1 (L-channel) IN-REF (L-channel) Sound multiplex output L Ext.1-IN (L-channel) Ext.2-IN (L-channel) N.R. det. 1 (L-channel): Pin for connection of weighting filter externally attached.
0V 0V 0V 2.03 V 2.5 V 0V 0V 2.5 V
Pin40 (VCC1)
16
650
17
Pin40 (VCC1) 500 500 17
7.85 k 15 k
N.R. det. 2 (L-channel)
At non-signal: 0.4 V At typical input: 0.7 V
1 k 1 k
50
11
AN3672NFBP
s Terminal Equivalent Circuits (continued)
Pin No. 18 Equivalent circuit Description N.R. REF (L-channel)
ICs for VCR
Voltage (typ.) 2.5 V
Pin40 (VCC1) 17 k 200
17 k
18
8.5 k
500
7.5 k 7.5 k
500 20 k
26 k
6.5 VREG
20 k
47 k
340
19 20 Refer to pin 32
Pin25 (P/R VCC) 100 500 600 20 200 1 k 100 2 k 59 Pin21 5.75 k 59
CCA out (L-channel) Rec. DC1: Pin for DC feedback of rec. (+) amp.
2.5 V 2.5 V (Rec.)
21
Pin25 (P/R VCC) 7.7 21 7.7
COMMON: Output pin of rec. (+) amp. at recording. Termination SW pin of COMMON at playback.
480 51 k
2.5 V (Rec.) 0 V (PB)
12
ICs for VCR
s Terminal Equivalent Circuits (continued)
Pin No. 22 Equivalent circuit Description
AN3672NFBP
Voltage (typ.) 2.5 V (Rec.) 0.7 V (PB)
Pin25 (P/R VCC) 20 375 59 22 5.95 k 20 15 k
P/R term 1: Output pin of rec. (-) amp. at recording. Head amp. input pin at playback.
23 24 25 26 27 Refer to pin 20 Refer to pin 22
P/R GND P/R term 2
0V At rec.: 2.5 V At PB: 0.7 V 5V 2.5 V
P/R VCC Rec. DC2: Pin for DC feedback of rec. (-) amp. Pin25 2 k 47.6 k Audio FF: High: 3.5 V to 5 V Low: 0 V to 1.5 V
Pin40 (VCC1)
27
23 k 1.7 k 1.7 k
5V
0V
ENV-det.: 3.7 V or more at rec. fO adj. completion
28
Pin40 (VCC1) 1.7 k 28 200 102 k
29
Pin40 (VCC1)
500 30.6 k 10.2 k 1 k 10 k
HA out: Common use for rec.-mute control pin
1.8 V
29
30
30 200 20 k
FM in
0V
13
AN3672NFBP
s Terminal Equivalent Circuits (continued)
Pin No. 31 Equivalent circuit Description
ICs for VCR
Voltage (typ.)
VCC1 1.7 k 31 1.7 k
VCC1 3.4 k
P/R VCC 2 k
Noise det. : At playback: N-det. At recording: Rec. AGC-det.
102 k 1.7 k 61.2 k 3.4 k 1.75 k
68 k 1.7 k
32
CCA out (R-channel): Pin for connection of N.R.-emph. capacitor externally attached.
0V
32
3.9 k
200 12 k
NR-VREF
33 34 Refer to pin 18 Refer to pin 17 N.R. REF (R-channel) N.R. det. 2 (R-channel) 2.5 V At non-signal: 0.4 V At typical input: 0.7 V 2.5 V 0V
35 36
Refer to pin 16 Pin40 (VCC1) 13.6 k 2.55 k 600 3.4 k 500 k 6.25 k 2.55 k
N.R. det. 1 (R-channel) Mute CTL: Mute-on: 5 V Mute-off: 0 V or open
36
37
Pin25 (P/R VCC)
Pin40 (VCC1)
Rec. AGC adj.
1.7 V
85 k 10.2 k
1.75 k 37
200 200
38
10.2 k
GND1 (R-channel)
0V
14
ICs for VCR
s Terminal Equivalent Circuits (continued)
Pin No. 39 Equivalent circuit Description PE
AN3672NFBP
Voltage (typ.)
39
40 41 42
Pin40 (VCC1) 3.4 k 1.7 k 1.7 k
VCC1 Logic GND Clock: High: 2 V to 5 V Low: 0 V to 1 V
5V 0V
5V
42
0V
43
Pin40 (VCC1) 3.4 k 1.7 k 1.7 k
Data: High: 2 V to 5 V Low: 0 V to 1 V
5V
43
0V
44
Pin40 (VCC1)
Logic VCC REG
3.3 V
44 51 k 15 k
45
Pin40 (VCC1) 200 20 k 1 k
fSC
0V
45
46
Refer to pin 64
Main REF
2.5 V
15
AN3672NFBP
s Terminal Equivalent Circuits (continued)
Pin No. 47 Equivalent circuit
Pin51 (MTS VCC) 13.6 k 600 47 600 8 k 18 k
ICs for VCR
Description DEM REF
Voltage (typ.) 2.5 V
48
Pin51 (MTS VCC)
SIF / base band input
2.2 V
48
600 10.5 k 8 k
34 k
10.2 k
10.2 k
49
Pin51 (MTS VCC)
Sub level det.
2.5 V
600 49 600 10.2 k
50
Pin51 (MTS VCC)
Main out
2.5 V
50
20 k
51 52
Pin51 (MTS VCC) 200 52 600
MTS VCC DC out
5V 2.5 V
45 k
16
ICs for VCR
s Terminal Equivalent Circuits (continued)
Pin No. 53 Equivalent circuit
VCC2 50 53 100 k 50
AN3672NFBP
Description Line out (R-channel): Typical output level can be changed by serial setting.
Voltage (typ.) 6V
24 k 6.8 k
Same Same Same circuit circuit circuit as left as left as left
54 55 56
Pin51 (MTS VCC)
N.C. GND2 LED PORT
0V 0V
56
600
5.1 k 57 58 59 Refer to pin 53 Line out (L-channel) VCC2 6V 12 V 6V
VCC2 50 59 100 k 50
RFC AGC out: Typical output level can be changed by serial setting.
Same Same Same circuit circuit circuit 13.6 k as left as left as left
48 k
60
Pin40 (VCC1) 400 60 600 10.2 k 20 k 2 k
RFC AGC det.
Non fixed
17
AN3672NFBP
s Terminal Equivalent Circuits (continued)
Pin No. 61 Equivalent circuit Pin40 (VCC1) Description Normal out: Typical output level 1 kHz, -20 dBS
ICs for VCR
Voltage (typ.) 2.5 V
61 850 62 Normal in: Typical output level 1 kHz, -20 dBS 2.5 V
Pin40 (VCC1)
62
200 300 k VREF
63
Pin51 (MTS VCC) 5.1 k 600 63 600 5.1 k
Comp.
2.5 V
64
Sub REF
2.5 V
64 600
600
20 k 20 k
10.2 k
18
ICs for VCR
s Usage Note
When use this IC, note the following points. * Use paying attention to surge breakdown of this IC. (C = 200 pF, R = 0 ) Surge breakdown voltage 140 V to 200 V 200 V or more Corresponding pins 1, 3, 6, 17, 18, 20, 21 22, 24, 25, 33, 36, 53, 57 Except for above listed pins
AN3672NFBP
s Application Notes
1. PD Ta curves of QFH064-P-1414A PD T a
2200 2155 2000 1800 Glass epoxy board (50 x 50 x t0.8 mm3) Rth(j-a) = 58C/W PD = 2155 mW (25C)
Power dissipation PD (mW)
1600 1400 1330 1200 1000 800 600 400 200 0 0 Independent IC without a heat sink Rth(j-a) = 94C/W PD = 1330 mW (25C)
25
50
75
100
125
150
Ambient temperature Ta (C)
2. Rec. amp. output's dependence on resistance (Pin 37)
35 30
IOUT (mA[p-p])
25 20 15 10 5 0 10
20
30
40
50
60
70
Radj (k)
19
AN3672NFBP
s Application Notes (continued)
3. I2C bus of this IC 1) Serial control timing specification (1) Start and stop conditions
ICs for VCR
Data
tBUF
tLOW
tr
Clock tSU;STO Stop condition
Stop condition
tHD;STA Start condition
(2) Data recognition condition Data line Stable state: data is valid. Data (Pin43) tf tHIGH Clock (Pin42) Data is variable.
tSU;DAT (3) Recommended operation condition Parameter Bus free time between stop and start conditions
tHD;DAT
Symbol tBUF tHD;STA tLOW tr tSU;STO tSU;DAT tHIGH tf tHD;DAT fSCL
Min 4.7 4.0 4.7 4.0 250 4.0 5.0 0
Max 1 000 300 100
Unit s s s ns s ns s ns s kHz
Hold time start condition (The first clock pulse is generated after this period.) Low state hold time of clock Rise time of data and clock signal Setup time of stop condition Data setup time High state hold time of clock Fall time of data and clock signal Data hold time Clock frequency
20
ICs for VCR
s Application Notes (continued)
3. I2C bus of this IC (continued) 2) Data specification (1) Slave address: 1 1 1 0 1 01 0
AN3672NFBP
(2) Slave address format
S SLAVE ADDR A Sub ADDR A Data BYTE A P
Start condition
Acknowledge bit
Stop condition
(3) Sub-address byte and data byte format: The underlined figures stand for the initial state. AN3672FBP Serial mode
Sub D7 address (HEX) Rec. / PB 00 0 = PB 1 = Rec. D6 D5 D4 D3 D2 D1 D0
HiFi input select 0, 0 = Sound multiplex 0, 1 = Ext.1 1, 0 = Ext.2 1, 1 = Ext.3 Nor detection 0, 0 = High 0, 1 = MID 1, 0 = Low 1, 1 = Off Rec. FM mix. ratio 0, 0 = 11 dB 0, 1 = 10 dB 1, 0 = 9 dB 1, 1 = 8 dB Power save Rec. mode 0 = Off 0, 0 = NOR (0 dB) 1 = On 0, 1 = S-VHS (-2 dB) 1, 0 = Over rec. (2 dB) 1, 1 = xxxx Line out gain 0 = -6.0 dBS 1 = -7.5 dBS
NOR input select 0, 0 = xxxx 0, 1 = R-ch. 1, 0 = L-ch. 1, 1 = R/L-mix.
01
02
03
Output mode select Output channel select 0, 0 = HiFi 0, 0 = Stereo 0, 1 = Mix. 0, 1 = L-ch. 1, 0 = NOR 1, 0 = R-ch. 1, 1 = BS mon 1, 1 = xxxx DOC select ENV select VCC2 select 0 = On 0 = ENV 0=9V 1 = Off (linear) 1 = 12 V 1 = FORCE NOR (0/5 V) HSW polarity 0 = Normal 1 = Reverse
04 05 06 ZAP-mode 0 = DAC 1 = PROM fO monitor 0 = Off 1 = On fO-adj. start fSC-SEL 0 = Off 0, 0 = 3.58 MHz 0, 1 = 4.43 MHz 1 = On 1, 0 = 7.16 MHz 1, 1 = 8.86 MHz HOLD-TEST ENC/sound multiplex test 0 = Off 0, 0 = Off 1 = On 0, 1 = Sound multiplex 1, 0 = ENC 1, 1 = Off fO-check 0 = Off 1 = On FM-test 0 = Off 1 = On INSW-mute 0 = Off 1 = On
0 fixed
07
08 09 A B TEST1 0 = Off 1 = On Adj 0 = Off 1 = On Bilingual mode CTL 0, 0 = BOTH 1, 0 = Sub 0,1 = Main 1,1 = xxxx Forced MON Sound mute 0 = Off 0 = Off 1 = On 1 = On Input select 0 = 4.5 MHz 1 = Base band
21
AN3672NFBP
s Application Notes (continued)
3. I2C bus of this IC (continued) 3) Auto increment function S SLAVE ADDR A Sub ADDR * A Data 0 A Data 1 A Data 2
ICs for VCR
A
P
Start condition
Acknowledge bit Sub ADDR 10000000 (HEX: 80) 11000000 (HEX: C0)
Stop condition Contents 00 to 03 data of sub ADDR can be controlled by the above format. 00 to 05 data of sub ADDR can be controlled by the above format.
Once the data is inputted as shown above, the specified sub-address data is set to Data 0, one increment data to Data 1, further one increment data to Data 2. In this way, the plural data can be controlled at one time. 4) VCO fO auto adjusting manual 1. Power on 2. Setting 1 (INSW mute = On) IC mode setting: Rec. (*0 D7 = 1) Power save = Off (*3 Except for D6 and D7 = 1) INSW Mute
Wait 1.5 s or more
Serial
*6
D1 01
Ex. *6 0 0 0 0 0 0 1 0
3. Setting 2 (Selection of fSC frequency to be used.) Sub-address
*6
Ex. When you use fSC = 7.16 MHz, *6 0 0 1 0 0 0 1 0 fSC select INSW mute continues 4.43 MHz 7.16 MHz 8.86 MHz
D5 D4 fSC frequency 0 0 3.58 MHz
Wait 0.1 s or more
0 1 1
1 0 1
4. Adjustment start (fO adj. start = On) Ex. Serial
Max. within 0.5 s
fO adj. start
*6
D6 01
*6
01100010 Setting hitherto continues
5. Adjustment completion ENV det. output (pin 28) potential Informs of completion with low to high 6. Setting cancellation fO adj. start = Off INSW mute. = Off Serial Serial Approx. 4 V Approx. 0.5 V
*6 *6
D6 1 0 D1 1 0
7. Transmission of normal data
Note) Input level of fSC is 100 mV[p-p] to 500 mV[p-p].
22
ICs for VCR
s Application Notes (continued)
3. I2C bus of this IC (continued) 5) Serial mode of sound multiplex Broadcasting signal Bilingual Serial setting Sub address (B) D4 0 0 1 D3 0 1 0 D2 Forced monaural 0 0 0 1 0 1 L-ch. Main Main Sub Main L L+R L+R R-ch. Sub Main Sub Main R L+R L+R Contents Both Main Sub Mono Stereo Mono Mono Bilingual CTL Line out
AN3672NFBP
LED-PORT (Pin 56) min. 2.7 V to (typ. 3.1 V)
Stereo
Mono
* * * *
* * * *
min. 1.3 V to max. 1.9 V (typ. 1.6 V) max. 0.4 V (typ. 0.1 V)
*
6) Precautions on MTS application circuit (1) When an external input is selected with large amplitude noise into an input pin of television sound multiplex block, an appropriate signal to noise ratio is not always guaranteed. On use of SIF input, you can counter this problem by switching the setting from SIF to base band input through a serial control when using an external input. In this time, however, a timing control is required to return it to SIF in advance so as not to cause any shock noise which is likely to come out when HiFi input selector returns to television sound multiplex side. On use of a base band input, it is recommended that you perform muting outside to prevent from noise being inputted into television sound multiplex. (2) On use of television sound multiplex with a base band input, if you adjust an input level for 106 mV[rms] (= 300 mV[p-p]) with mono 100% modulation pre-emphasis off, the IC is in a state of an optimum separation. When you can not obtain an appropriate separation due to deviation of input signal frequency characteristics, however, you can adjust separation by fitting a volume of 100 k between pin 47 and GND. As the IC is already adjusted for an optimum separation with the above reference input, you can substitute the input level adjusting volume for a separation adjustment. In this case, do not forget to set pin 47 to open. (3) On use of sound multiplex with SIF input, an SIF input level from a tuner be set to 90 dBV 10 dBV against a typical RF electric field input. To get an appropriate separation without adjustment, you are required to use the flattest possible SIF-BPF band width that does not cause any delay time difference between main and sub in the range of 4.5 MHz 42 kHz. Likewise, use the gain band width which is broad enough not to attenuate cue signal carrier where a main component of 4.5 MHz 55 kHz. (4) In the tuner characteristics, a demodulation linearity must be set to 250% or more modulation to prevent the sub-carrier signal from being damaged by over-modulation of pre-emphasis in a higher band width. (5) The stereo modulator must be used with good characteristics and well-calibrated equipment at measurement of separation. When using SIF input, FM modulation factor must be tuned exactly so as to be 25 kHz at mono 100% modulation and pre-emphasis off. At the same time, measurement must be done by using the LPF which can attenuate 20 dB or more at 30 kHz between line-out and AC level-meter.
23
AN3672NFBP
s Application Notes (continued)
3. I2C bus of this IC (continued) 6) Precaution on MTS application circuit (continued) (6) The case without adjustment (SIF mode)
IC inside
ICs for VCR
Input signal selection 47 3.3 F
4.5 MHz BPF output Tuner 4.5 MHz BPF 0.1 F 48
SIFDEMO
VCA
To sound multiplex circuit
(7) The case adjustment is necessary (Base band mode)
Separation adjustment 100 k IC inside 47 Tuner SIF-DEM A point 4.5 MHz BPF Base band signal 1 F 48 Input signal selection
To separation adjustment
SIFDEMO
VCA
To sound multiplex circuit Input level adjustment "A point" 106 mV[rms] (at 1 kHz, mono 100% Mod.)
Note) Pin 47 must be open when separation is adjusted with the potentiometer of input level adjustment.
24
ICs for VCR
s Application Notes (continued)
3. I2C bus of this IC (continued) 7) Descriptions on data bit function (1) Sub address 00000000
Note) The underlined values are for the initial status at power on.
AN3672NFBP
Function Rec./PB changeover
Value 0 1 HiFi-PB Mode HiFi-EE (Rec.) Mode Sound multiplex select
Conditions
HiFi input changeover
00 01 10 11
Ext.1 select (pin 9, pin 14 input) Ext.2 select (pin 10, pin 15 input) Ext.3 select (pin 2, pin 4 input) Setting is disable. R-channel selection of HiFi input signal L-channel selection of HiFi input signal L+R mixed selection of HiFi input signal
NOR input changeover
00 01 10 11
(2) Sub address 00000001
Note) The underlined values are for the initial status at power on.
Function Output gain changeover
Value 0 1
Conditions Line output 1 (typ. -6.0 dBS for typical input) Line output 2 (typ. -7.5 dBS for typical input) High (Least to be NOR) MID Low Off HiFi select HiFi + NOR mix. select NOR select BS monitor select Stereo selection L-ch. BPF monitor selection at L-ch. selection and PB R-ch. BPF monitor selection at R-ch. selection and PB Setting is disable.
Noise det. threshold value (Normal det. level)
00 01 10 11
Output mode changeover
00 01 10 11
Output channel chengeover
00 01 10 11
25
AN3672NFBP
s Application Notes (continued)
3. I2C bus of this IC (continued) 7) Descriptions on data bit function (continued) (3) Sub address 00000010
Note) The underlined values are for the initial status at power on.
ICs for VCR
Function FM mix. ratio at recording
Value 00 01 10 11
Conditions FM carrier R/L = 11 dB FM carrier R/L = 10 dB FM carrier R/L = 9 dB FM carrier R/L = 8 dB DOC on DOC off ENV on Force NOR (0/5 V) Select at using VCC2 = 9 V (output DC = 4.5 V) Select at using VCC2 = 12 V (output DC = 6.0 V)
DOC select
0 1
ENV select
0 1
VCC2 selection
0 1
(4) Sub address 00000011
Note) The underlined values are for the initial status at power on.
Function Power save
Value 0 1 Power save off Power save on Normal mode (0 dB) S-VHS mode (-2 dB) Over rec. mode (2 dB) Prohibited
Conditions
Rec. amp. mode
00 01 10 11
HEAD SW mode
0 1
Normal mode AFF = H1, Ch.1 Turn over mode AFF = H1, Ch.2
26
ICs for VCR
s Application Notes (continued)
3. I2C bus of this IC (continued) 7) Descriptions on data bit function (continued) (5) Sub address 00000110
Note) The underlined values are for the initial status at power on.
AN3672NFBP
Function ZAP mode (use for the inspection) VCO fO-adj.
Value 0 1 0 1 DAC mode PROM mode fO-adj. off fO-adj. start on 3.58 MHz select 4.43 MHz select 7.16 MHz select 8.86 MHz select Check off Check on INSW-mute off INSW-mute on
Conditions
fSC select
00 01 10 11
VCO fO-check
0 1
INSW-mute (SW30, SW31) (6) Sub address 00000111
0 1
Note) The underlined values are for the initial status at power on.
Function fO monitor Pin 29 Hold-test (use for the inspection) ENC/sound multiplex-test (use for the inspection)
Value 0 1 0 1 00 01 10 11 Monitor off Monitor on Test mode off Test mode on Test mode off
Conditions
Sound multiplex test mode on ENC test mode on Test mode off Test mode off Test mode on
FM-test (use for the inspection)
0 1
27
AN3672NFBP
s Application Notes (continued)
3. I2C bus of this IC (continued) 7) Descriptions on data bit function (continued) (7) Sub address 00001011
Note) The underlined values are for the initial status at power on.
ICs for VCR
Function Sound multiplex test 1 (use for the inspection) Sound multiplex adj. test (use for the inspection) Bilingual mode select
Value 0 1 0 1 00 01 10 11 Test mode off
Conditions
Test mode on (L-ch.: SIFOUT, R-ch.: 3.5fH BPF) Test mode off Test mode on (L-ch.: 952 BPF, R-ch.: Sub De-emph.) Both Main Sub Setting is disable. Forced mono off Forced mono on Sound multiplex mute off Sound multiplex mute on SIF 4.5 MHz input Base band input
Forced mono
0 1
Sound multiplex mute
0 1
Sound multiplex input select
0 1
8) Usage notes of I2C bus * Serial data transmission When transmitting one line of data, it is necessary to send the Start and Stop conditions at each transmission. To change a serial mode setting, you can change it by sending one line of the changed data.
< Example: In case of sending all data of four lines >
Sub address
Sub address
Address
Address
ACK
ACK
ACK
ACK
ACK
ACK
Start
Start
Data
Data
Stop
1st line of data
2nd line of data
Sub address
Stop
Sub address
Address
Address
ACK
ACK
ACK
ACK
ACK
ACK
Start
Start
Data
Data
Stop
3rd line of data
28
4th line of data
Stop
Can be adjusted also at base-band input Open N.R. REF (R) N.R. det. 2 (R) Main REF DEM REF
ICs for VCR
(Serial setting at 33k: NOR25 mA[p-p]/ch. SVHS20 mA[p-p]/ch. Over-rec.30 mA[p-p]/ch.)
Rec. AGC adj. GND1 (R) PE VCC1 (5 V) Logic GND I2C clock I2C data Logic VCC REG 10 F fSC MTS mute CTL (H1 = Mute on)
10 F
10 F
Base band 47 37 38 39 40 41 42 43 44 45 35 34 33 46
SIF IN Base band IN
100 k 3.3 F 33 k 1 F SIF input
0.1 F
1 F
SIF input
N.R. det. 1 (R) 33 F Mute CTL (High = Mute on) 36
VCC (Pin 51) Sub-level det.
1 F
48
49
s Application Circuit Example
Main out
50
MTS VCC (5 V)
10 F
51
DC out
52
0.1 F
Line out (R)
100 10 F
32 0.015 F CCA out (R) 31 Noise det./ Rec. AGC det. Rec. mute (L) 30 0.22 F FM in (Mute-off H1) 29 HA out (fO / BPF monitor) 28 Force NOR(NOR = L) common use for ENV-det. output 27 0.01 F Audio FF input 26 Rec. DC2 25 0.1 F P/R VCC 0.01 F 24 23 P/R GND 22
0.01 F
HEAD1
GND2 LED PORT (Multi-values output) Line out (L) VCC2 (12 V)
HEAD2
RFC AGC out
53 N.C. 54 55 56 100 10 F 57 58 10 F 59
21 20 0.1 F 19 0.015 F 18 17
10 F
COMMON Rec. DC1
10 F
RFC AGC det.
22 F
60
Normal out
1 kHz, -20 dBS 10 F
61
Normal in
1 kHz, -20 dBS
62
Comp. 13 12 11 10 9 8 7 6
0.47 F
CCA out (L) N.R. REF (L) N.R. det. 2 (L) 14 16 15
33 F
63
Sub REF
4.7 F
1 F
64
Ext.1-IN (L)
5 0.1 F CUE det. 4 Ext.3-IN (L) 3 BS-IN (L) 2 Ext.3-IN R) 1 BS-IN (R)
N.R. det. 1 (L) Ext.2-IN (L)
Sound multiplex output L Zero bias input 1 kHz, -26.8 dBS
IN-REF (L) GND1 (L) Ext.2-IN (R) Ext.1-IN (R) Sound multiplex 4.7 F output R IN-REF (R) 10 F VREF
AN3672NFBP
Zero bias input 1 kHz, -26.8 dBS
29

▲Up To Search▲

Price & Availability of AN3672NFBP

	To Download AN3672NFBP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .