Part Number Hot Search : 
010LF BUV50 TS1102 BUW133A BADXCF A35BD BR301 P100M1
Product Description
Full Text Search
 

To Download AD7305 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 a
FEATURES Four 8-Bit DACs in One Package +3 V, +5 V and 5 V Operation Rail-to-Rail REF-Input to Voltage Output Swing 2.6 MHz Reference Multiplying Bandwidth Compact 1.1 mm Height TSSOP 16-/20-Lead Package Internal Power ON Reset SPI Serial Interface Compatible--AD7304 Fast Parallel Interface--AD7305 40 A Power Shutdown APPLICATIONS Automotive Output Span Voltage Instrumentation, Digitally Controlled Calibration Pin-Compatible AD7226 Replacement when V DD < 5.5 V
VDD PWR ON RESET
+3 V/+5 V, Rail-to-Rail Quad, 8-Bit DAC AD7304/AD7305*
FUNCTIONAL BLOCK DIAGRAMS
VREFB VREFA INPUT 8 REG A 8 INPUT 8 REG B CS SDI/SHDN CLK SERIAL REG INPUT 8 REG C INPUT 8 REG D DAC B 8 REG DAC C 8 REG DAC D 8 REG DAC B VOUTB DAC A REG 8 DAC A VOUTA
DAC C
VOUTC
DAC D
VOUTD
AD7304
VSS GND VDD CLR LDAC VREFC VREFD VREF INPUT 8 REG A INPUT 8 REG B INPUT 8 REG C 8 INPUT 8 REG D WR A0/SHDN A1 DECODE DAC D 8 REG DAC D VOUTD DAC A 8 REG DAC B 8 REG DAC C 8 REG
GENERAL DESCRIPTION
The AD7304/AD7305 are quad, 8-bit DACs that operate from a single +3 V to +5 V supply or 5 V supplies. The AD7304 has a serial interface, while the AD7305 has a parallel interface. Internal precision buffers swing rail-to-rail. The reference input range includes both supply rails allowing for positive or negative fullscale output voltages. Operation is guaranteed over the supply voltage range of +2.7 V to +5.5 V, consuming less than 9 mW from a +3 V supply. The full-scale voltage output is determined by the external reference input voltage applied. The rail-to-rail VREF input to DAC VOUT allows for a full-scale voltage set equal the positive supply VDD, the negative supply VSS or any value in between. The AD7304's doubled-buffered serial-data interface offers high speed, three-wire, SPI and microcontroller compatible inputs using data in (SDI), clock (CLK) and chip select (CS) pins. Additionally, an internal power-on reset sets the output to zero scale. The parallel input AD7305 uses a standard address decode along with the WR control line to load data into the input registers. The double buffered architecture allows all four input registers to be preloaded with new values, followed by a LDAC control strobe which copies all the new data into the DAC registers thereby updating the analog output values. When operating from less than +5.5 V, the AD7305 is pin-compatible with the popular industry standard AD7226.
PWR ON RESET DB0 DB1 DB2 DB3 DB4 DB5 DB6
DAC A
VOUTA VOUTB
DAC B
DAC C
VOUTC
AD7305
LDAC VSS GND
An internal power ON reset places both parts in the zero-scale state at turn ON. A 40 A power shutdown (SHDN) feature is activated on both parts by tristating the SDI/SHDN pin on the AD7304, and tristating the A0/SHDN address pin on the AD7305. The AD7304/AD7305 are specified over the extended industrial (-40C to +85C), and the automotive (-40C to +125C) temperature ranges. AD7304s are available in 16-lead plastic DIP (N-16), and wide-body SOL-16 (R-16) packages. The parallel input AD7305 is available in the 20-lead plastic DIP (N-20), and the SOL-20 (R-20) surface mount package. For ultracompact applications the thin 1.1 mm TSSOP-16 (RU-16) package will be available for the AD7304, while the TSSOP-20 (RU-20) will house the AD7305.
*Protected under Patent Number 5684481.
REV. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 1998
AD7304/AD7305-SPECIFICATIONS V
Parameter STATIC PERFORMANCE Resolution1 Integral Nonlinearity2 Differential Nonlinearity Zero-Scale Error Full-Scale Voltage Error Full-Scale Tempco3 REFERENCE INPUT VREFIN Range Input Resistance (AD7304) Input Resistance (AD7305) Input Capacitance3 ANALOG OUTPUTS Output Voltage Range Output Current Drive Shutdown Resistance Capacitive Load3 LOGIC INPUTS Logic Input Low Voltage Logic Input High Voltage Input Leakage Current5 Input Capacitance3 AC CHARACTERISTICS3 Output Slew Rate Reference Multiplying Total Harmonic Distortion Settling Time6 Shutdown Recovery Time Time to Shutdown DAC Glitch Digital Feedthrough Feedthrough SUPPLY CHARACTERISTICS Positive Supply Current Negative Supply Current Power Dissipation Power Down Power Supply Sensitivity Symbol N INL DNL VZSE VFSE TCVFS VREFIN RREFIN RREFIN CREFIN VOUT IOUT ROUT CL VIL VIH IIL CIL SR BW THD tS tSDR tSDN Q Q VOUT/VREF IDD ISS PDISS IDD_SD PSS Condition
(@ VDD = +3 V or +5 V, VSS = 0 V; or VDD = +5 V and VSS = -5 V, VSS REF VDD, -40 C < TA < +85 C/+125 C, unless otherwise noted.)
3V 8 1 1 15 4 5 VSS/VDD 28 7.5 5 10% 5 V 8 1 1 15 4 5 VSS/VDD 28 7.5 5 VSS/VDD 3 120 200 0.8 2.4 10 8 1/3.6 10% 5V 8 1 1 15 4 5 VSS/VDD 28 7.5 5 VSS/VDD 3 120 200 0.8 2.4 10 8 1/3.6 2.6 0.025 1.0/2 2 15 15 2 -65 6 6 60 40 0.004 10% Units Bits LSB max LSB max mV max LSB max ppm/C typ4 V min/max k typ k typ pF typ V min/max mA typ k typ pF typ V min V max A max pF max V/s min/typ MHz typ % s typ/max s max s typ nVs typ nVs typ dB mA max mA max mW max A typ %/%
Monotonic, All Codes 0 to FFH Data = 00H Data = FFH
Code = 55H All DACs at Code = 55H
VSS/VDD Code = 80H, VOUT < 1 LSB 3 DAC Outputs Placed in Shutdown State 120 No Oscillation 200 0.6 2.1 10 8 Code = 00H to FFH to 00H Small Signal, VSS = -5 V VREF = 4 V p-p, VSS = -5 V, f = 1 kHz To 0.1% of Full Scale To 0.1% of Full Scale 1/2.7
1.1/2 2 15 15 2
1.0/2 2 15 15 2
Code = 00H, VREF =1 V p-p, f = 100 kHz VLOGIC = 0 V or VDD, No Load VSS = -5 V VLOGIC = 0 V or VDD, No Load SDI/SHDN = Floating VDD = 10% 6 15 40 0.004 6 30 40 0.004
NOTES 1 One LSB = V REF/256. 2 The first three codes (00 H, 01H, 10H) are excluded from the integral nonlinearity error measurement in single supply operation +3 V or +5 V. 3 These parameters are guaranteed by design and not subject to production testing. 4 Typicals represent average readings measured at +25C. 5 SDI/SHDN and A0/SHDN pins have 30 A maximum IIL input leakage current. 6 The settling time specification does not apply for negative going transitions within the last 3 LSBs of ground in single supply operation. Specifications subject to change without notice.
5V VREF = 10V p-p f = 20kHz 5V 0V
0V -5V VOUT = 10V p-p -5V (OUT) (IN)
Figure 1. AD7304/AD7305 Rail-to-Rail Reference Input to Output at 20 kHz -2-
REV. A
AD7304/AD7305 TIMING SPECIFICATIONS +85 C/125 C, unless otherwise noted.)
Parameter Symbol
1, 2
(@ VDD = +3 V or +5 V, VSS = 0 V; or VDD = +5 V and VSS = -5 V, VSS VREF VDD, -40 C < TA <
3V 10% 5V 10% 5V 10% Units
INTERFACE TIMING SPECIFICATIONS AD7304 Only Clock Width High tCH Clock Width Low tCL Data Setup tDS Data Hold tDH Load Pulsewidth tLDW Load Setup tLD1 Load Hold tLD2 Clear Pulsewidth tCLWR Select tCSS Deselect tCSH AD7305 Only Data Setup tDS Data Hold tDH Address Setup tAS Address Hold tAH Write Width tWR Load Pulsewidth tLDW Load Setup tLS Load Hold tLH
70 70 50 30 70 40 40 60 30 60 60 30 60 30 60 60 60 30
55 55 40 20 60 30 30 60 20 40 40 20 40 20 50 50 40 20
55 55 40 20 60 30 30 60 20 40 40 20 40 20 50 50 40 20
ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min
NOTES 1 These parameters are guaranteed by design and not subject to production testing. 2 All input control signals are specified with t R = tF = 2 ns (10% to 90% of V DD) and timed from a voltage level of 1.6 V.
ABSOLUTE MAXIMUM RATINGS*
ORDERING GUIDE
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V, +8 V VSS to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V, -8 V VREFX to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSS, VDD Logic Inputs to GND . . . . . . . . . . . . . . . -0.3 V, VDD + 0.3 V VOUTX to GND . . . . . . . . . . . . . . . . . . . . -0.3 V, VDD + 0.3 V IOUT Short Circuit to GND . . . . . . . . . . . . . . . . . . . . . 50 mA Package Power Dissipation . . . . . . . . . . . . . . (TJ MAX-TA)/JA Thermal Resistance JA 16-Lead Plastic DIP Package (N-16) . . . . . . . . . . 103C/W 16-Lead SOIC Package (R-16) . . . . . . . . . . . . . . . 73C/W TSSOP-16 Package (RU-16) . . . . . . . . . . . . . . . . 180C/W 20-Lead Plastic DIP Package (N-20) . . . . . . . . . . 120C/W 20-Lead SOIC Package (R-20) . . . . . . . . . . . . . . . 74C/W TSSOP-20 Package (RU-20) . . . . . . . . . . . . . . . . 155C/W Maximum Junction Temperature (TJ MAX) . . . . . . . . . +150C Operating Temperature Range . . . . . . . . . . . -40C to +85C Storage Temperature Range . . . . . . . . . . . . -65C to +150C Lead Temperature N-16 and N-20 (Soldering, 10 secs) . . . . . . . . . . . . +300C R-16, R-20, RU-16, RU-20 (Vapor Phase, 60 secs) . . +215C R-16, R-20, RU-16, RU-20 (Infrared, 15 secs) . . . . +220C
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Model AD7304BN AD7304BR AD7304YR AD7304BRU AD7305BN AD7305BR AD7305YR AD7305BRU
Temperature Range -40C/+85C -40C/+85C -40C/+125C -40C/+85C -40C/+85C -40C/+85C -40C/+125C -40C/+85C
Package Description 16-Lead P-DIP 16-Lead SOIC 16-Lead SOIC TSSOP-16 20-Lead P-DIP 20-Lead SOIC 20-Lead SOIC TSSOP-20
Package Options N-16 R-16 R-16 RU-16 N-20 R-20 R-20 RU-20
The AD7304/AD7305 contains 2759 transistors. Die size: 103 mil x 102 mil, 10,506 sq mil.
CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD7304/AD7305 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. A
-3-
AD7304/AD7305
SDI SA SI A1 A0 D7 D6 D5 D4 D3 D2 D1 D0
CLK
tCSS
CS
tCSH tLD2
LDAC
tLD1
SDI
tDS
CLK
tDH tCH tLDW tCLRW
1 LSB ERROR BAND
tCL
LDAC CLR FS VOUT ZS
tS
tS
Figure 2. AD7304 Timing Diagram
tSDN
SDI/SHDN
tSDR
IDD
Figure 3. AD7304 Timing Diagram
Table I. AD7304 Control Logic Truth Table CS H L + H H H CLK X + L X X X LDAC CLR H H H L H H H H H H - + Serial Shift Register Function No Effect Data Advanced 1 Bit No Effect No Effect No Effect No Effect Input REG Function No Effect No Effect Updated with SR Contents2 Latched with SR Contents 2 Loaded with 00H Latched with 00H DAC Register Function No Effect No Effect No Effect All Input Register Contents Transferred3 Loaded with 00H Latched with 00H
NOTES 1 + positive logic transition; - negative logic transition; X Don't Care. 2 One Input Register receives the data bits D7-D0 decoded from the SR address bits (A1, A0); where REG A = (0, 0); B = (0, 1); C = (1, 0); D = (1, 1). 3 LDAC is a level-sensitive input.
Table II. AD7304 Serial Input Register Data Format, Data Is Loaded in the MSB-First Format
MSB B11 AD7304 SAC
B10 SDC
B9 A1
B8 A0
B7 D7
B6 D6
B5 D5
B4 D4
B3 D3
B2 D2
B1 D1
LSB B0 D0
If B11 (SAC), Shutdown All Channels, is set to logic LOW, all DACs are placed in a power shutdown mode, all output voltages become high resistance. If B10 (SDC), Shutdown Decoded Channel, is set to logic LOW, only the DAC decoded by address bits A1 and A0 is placed in the shutdown mode.
-4-
REV. A
AD7304/AD7305
Table III. AD7305 Control Logic Truth Table
WR L + L + L + L + H L H H
A1 L L L L H H H H X X X X
A0 L L H H L L H H X X X X
LDAC Input Register Function H H H H H H H H L L + H REG A Loaded with DB0-DB7 REG A Latched with DB0-DB7 REG B Loaded with DB0-DB7 REG B Latched with DB0-DB7 REG C Loaded with DB0-DB7 REG C Latched with DB0-DB7 REG D Loaded with DB0-DB7 REG D Latched with DB0-DB7 No Effect Input REG x Transparent to DB0-DB7 No Effect No Effect, Device Not Selected
DAC Register Function Latched with Previous Contents, No Change Latched with Previous Contents, No Change Latched with Previous Contents, No Change Latched with Previous Contents, No Change Latched with Previous Contents, No Change Latched with Previous Contents, No Change Latched with Previous Contents, No Change Latched with Previous Contents, No Change All Input Register Contents Loaded, Register Transparent Register Transparent All Input Register Contents Latched No Effect, Device Not Selected
PIN CONFIGURATIONS
NOTES 1 + positive logic transition; - negative logic transition; X Don't Care. 2 LDAC is a level sensitive input.
tWR
WR
VOUTB 1 VOUTB 1
16 15 14
20 19 18 17
VOUTC VOUTD VDD A0/SHDN A1
VOUTC VOUTD VDD VREFC
VOUTA 2 VSS 3 VREF 4 GND 5 LDAC 6
tAS
A0, A1
tAH
VOUTA 2 VSS 3 VREFA 4
AD7304
13
AD7305
16
tDS
D0-D7
tDH
TOP VIEW VREFB 5 (Not to Scale) 12 VREFD GND 6 LDAC 7
11 10 9
SDI/SHDN CLK CS
TOP VIEW 15 WR (Not to Scale) 14 DB0 DB7 7 DB6 8 DB5 9 DB4 10
13 12 11
DB1 DB2 DB3
tLS
LDAC
tLH
tLDW
CLR 8
tS
VOUT 1 LSB ERROR BAND
Figure 4. AD7305 Timing Diagram
tSDN
A0/SHDN
tSDR
IDD
Figure 5. AD7305 Timing Diagram
REV. A
-5-
AD7304/AD7305
AD7304 PIN FUNCTION DESCRIPTIONS Pin # Name 1 2 3 4 5 6 7 8 9 10 11 VOUTB VOUTA VSS VREFA VREFB GND LDAC CLR CS CLK SDI/SHDN Function Channel B rail-to-rail buffered DAC voltage output. Full scale set by reference voltage applied to V REFB pin. Output is open circuit when SHDN is enabled. Channel A rail-to-rail buffered DAC voltage output. Full scale set by reference voltage applied to V REFA pin. Output is open circuit when SHDN is enabled. Negative Power Supply Input. Specified range of operation 0 V to -5.5 V. Channel A Reference Input. Establishes VOUTA full-scale voltage. Specified range of operation VSS < VREFA < VDD. Channel B Reference Input. Establishes V OUTB full-scale voltage. Specified range of operation VSS < VREFB < VDD. Common Analog and Digital Ground. Load DAC register strobe, active low. Transfers all four Input Register data into their DAC registers. Asynchronous active low input. DAC Register is transparent when LDAC = 0. See Control Logic Truth Table for operation. Clears all Input and DAC registers to the zero condition. Asynchronous active low input. The serial register is not effected. Chip Select, Active Low Input. Disables shift register loading when high. Transfers Serial Input Register Data to the decoded Input Register when CS returns HIGH. Does not effect LDAC operation. Clock input, positive edge clocks data into shift register. Disabled by chip select CS. Serial Data-Input loads directly into the shift register, MSB first. Hardware shutdown (SHDN) control input, active when pin is left floating by a three-state logic driver. Does not effect DAC register contents as long as power is present on VDD. Channel D Reference Input. Establishes VOUTD full-scale voltage. Specified range of operation VSS < VREFD < VDD. Channel C Reference Input. Establishes VOUTC full-scale voltage. Specified range of operation V SS < VREFC < VDD. Positive power supply input. Specified range of operation +2.7 V to +5.5 V. Channel D rail-to-rail buffered DAC voltage output. Full-scale set by reference voltage applied to V REFD pin. Output is open circuit when SHDN is enabled. Channel C rail-to-rail buffered DAC voltage output. Full-scale set by reference voltage applied to V REFC pin. Output is open circuit when SHDN is enabled. AD7305 PIN FUNCTION DESCRIPTIONS Pin # Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 VOUTB VOUTA VSS VREF GND LDAC DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 WR A1 A0/SHDN VDD VOUTD VOUTC Function Channel B rail-to-rail buffered DAC voltage output. Full scale set by reference voltage applied to V REFB pin. Output is open circuit when SHDN is enabled. Channel A rail-to-rail buffered DAC voltage output. Full scale set by reference voltage applied to V REFA pin. Output is open circuit when SHDN is enabled. Negative Power Supply Input. Specified range of operation 0 V to -5.5 V. Channel B Reference Input. Establishes V OUT full-scale voltage. Specified range of operation V SS < VREF < VDD. Common Analog and Digital Ground. Load DAC register strobe, active low. Transfers all four Input Register data into their DAC registers. Asynchronous active low input. DAC Register is transparent when LDAC = 0. See Control Logic Truth Table for operation. MSB Digital Input Data Bit. Data Bit 6. Data Bit 5. Data Bit 4. Data Bit 3. Data Bit 2. Data Bit 1. LSB Digital Input Data Bit. Write data into Input Register control line, active low. See Control Logic Truth Table for operation. Address Bit 1. Address Bit 0/Hardware shutdown (SHDN) control input, active when pin is left floating by a three-state logic driver. Does not effect DAC register contents as long as power is present on V DD. Positive Power Supply Input. Specified range of operation +2.7 V to +5.5 V. Channel D rail-to-rail buffered DAC voltage output. Full scale set by reference voltage applied to V REFD pin. Output is open circuit when SHDN is enabled. Channel C rail-to-rail buffered DAC voltage output. Full scale set by reference voltage applied to V REFC pin. Output is open circuit when SHDN is enabled.
12 13 14 15 16
VREFD VREFC VDD VOUTD VOUTC
-6-
REV. A
Typical Performance Characteristics-AD7304/AD7305
144 VDD = +5V VSS = -5V VREF = VDD DATA = 00H 96
INL - LSB
1.0
120
IOUT SINK CURRENT - mA
0.6 DAC D 0.2
72
-0.2 DAC B VDD = +5V VSS = -5V DATA = 80H TA = +25 C
DAC C DAC A
48 -0.6
24
0
0
3
6 VOUT - mV
9
12
15
-1.0 -5.0
-3.0 -1.0 1.0 3.0 REFERENCE INPUT VOLTAGE - Volts
5.0
Figure 6. IOUTSINK vs. VOUT Rail-to-Rail Performance
Figure 9. INL vs. Reference Input Voltage
-35 VDD = +5V VSS = -5V VREF = VDD DATA = FFH
0.500 0.375 0.250 0.125 0.000 -0.125 -0.250 VDD = +5V VSS = -5V VREF = 2.5V
IOUT SOURCE CURRENT - mA
-28
-14
-7
DNL - LSB
-21
-0.375
0 4.0
4.2
4.4 4.6 4.8 VOUT OUTPUT VOLTAGE - Volts
5.0
-0.500
0
32
64
96 128 160 CODE - Decimal
192
224
256
Figure 7. IOUTSOURCE vs. VOUT Rail-to-Rail Performance
Figure 10. DNL vs. Code
1 0 DAC A 1 0
INL - LSB
4.0 VDD = +5.5V VSS = 0V VREF = +5.45V
ZERO SCALE VOLTAGE - mV
256
-1
3.6
DAC B -1 1 0 -1 1 0 -1 0 32 DAC D 64 96 128 160 CODE - Decimal 192 224 DAC C VDD = +5V VSS = -5V VREF = +2.5V TA = +25 C
3.2
2.8
2.4
2.0 -55
-35
-15
5
25 45 65 TEMPERATURE - C
85
105
125
Figure 8. INL vs. Code, All DAC Channels
Figure 11. Zero Scale Voltage vs. Temperature
REV. A
-7-
AD7304/AD7305
CS
VOUT
VDD = +5V VREF = +4V DATA = 00H FFH
NO LOAD RL = 70k RL = 10k
VDD = +5V CL = 150pF
0V 5V 0V
VOUT
CS
2 s/DIV
5 s/DIV
Figure 12. Large-Signal Settling Time
Figure 15. Time to Shutdown
CS
5V VREFIN ( 5V @ 50kHz) DATA = FFH 0V -5V 5V 0V VOUTA -5V
IDD 1mA/V
VDD = +5V VOUT
2 s/DIV
Figure 13. Multiplying Mode Step Response and Output Slew Rate
Figure 16. Shutdown Recovery Time (Wakeup)
6 VDD = +5V VSS = -5V DATA = FFH VREF = 100mV rms
10 VDD = +5V VSS = -5V 1
A
4
GAIN - dB
THD - %
10M
0
0.1
-4
f-3dB = 2.6MHz
0.010
-6
-8 10k
100k 1M FREQUENCY - Hz
0.001 10m
1
2
3 4 5 6 7 VREF AMPLITUDE - V p-p
8
9
10
Figure 14. Multiplying Mode Gain vs. Frequency
Figure 17. THD vs. Reference Input Amplitude
-8-
REV. A
AD7304/AD7305
1 VDD = +5V VSS = -5V
A
VDD = +5V VSS = -5V VREF = 2.5V F = 1MHz DATA = 80H
0.1
THD - %
VOUT
7FH
0.010
CS
0.001 20
100
1k FREQUENCY - Hz
10k
100k
Figure 18. THD vs. Frequency
Figure 21. Midscale Transition Glitch
3.0 VDD = +5V VSS = -5V VREF = 4V DATA = FFH
CROSS TALK - dB
40 20 0 -20 -40 -60 -80 -100 -120 -140 CT = 20 LOG V
OUTB REF
2.4
NOISE DENSITY - V/ Hz
VDD = +5V VSS = -5V VREF = 50mV rms DAC A DATA = FFH DAC B, C, D DATA = 00H
1.8
1.2
0.6
V
0 1 10 100 1k FREQUENCY - Hz 10k 100k
-160 100
1k
10k 100k FREQUENCY - Hz
1M
10M
Figure 19. Output Noise Voltage Density vs. Frequency
Figure 22. Crosstalk vs. Frequency
60 -PSRR, VSS = -5V 50 10% +PSRR, VDD = +5V 10%
40
VOUTB VDD = +5V VSS = -5V VREF = 2.5V DAC A = FFH DAC B = OOH F = 2MHz CLK
PSRR - dB
-PSRR, VSS = -3V 30 +PSRR, VDD = +3V 10%
10%
20
10
DATA = 80H TA = +25 C 100 1k FREQUENCY - Hz 10k 100k
0 10
50ns/DIV
Figure 20. Digital Feedthrough
Figure 23. Power Supply Rejection vs. Frequency
REV. A
-9-
AD7304/AD7305
12 VDD = +5V VSS = -5V VREF = 2.5V A0 = 5V ALL OTHER DIGITAL PINS VARYING 80 VDD = +5.5V VSS = -5.5V VREF = 2.5V PIN A0 FLOATING 10 SUPPLY CURRENT - mA 70
8
SHUTDOWN SUPPLY - A
5
60
6
IDD
50
4 ISS 2
40
30
0
0
1 2 3 DIGITAL INPUT VOLTAGE - Volts
4
20 -55
-35
-15
5 25 45 65 TEMPERATURE - C
85
105
125
Figure 24. Supply Current vs. Digital Input Voltage
Figure 27. Shutdown Supply Current vs. Temperature
10.0000
0.08 READING MADE AT TA = +25 C SAMPLE SIZE = 924 UNITS 0.04
1.0000
0.1000
VDD = +5V VSS = -5V VREF = 2.5V ALL DIGITAL PINS VARY, EXCEPT A0 = 5V IDD
NORMALIZED TOTAL UNADJUSTED ERROR DRIFT - LSB
SUPPLY CURRENT - mA
VDD = 2.7V 0
0.0100
0.0010
ISS
-0.04
VDD = 5.5V
0.0001 0 1 2 3 4 DIGITAL INPUT VOLTAGE - Volts 5
-0.08
0
84
168 252 336 DEGREES CELCIUS
420
504
Figure 25. Shutdown Supply Current vs. Digital Input Voltage (A0 Only)
Figure 28. Normalized TUE Drift Accelerated by Burn-In Hours of Operation @ 150C
5.0 VDD = +5V VSS = -5V VREF = 2.5V IDD AND ISS 3.8
4.4
SUPPLY CURRENT - mA
3.2
2.6
2.0 -55
-35
-15
5 25 45 65 TEMPERATURE - C
85
105
125
Figure 26. Supply Current vs. Temperature
-10-
REV. A
AD7304/AD7305
CIRCUIT OPERATION
The AD7304/AD7305 are a set of four-channel, 8-bit, voltageoutput, digital-to-analog converters differing primarily in digital logic interface and number of reference inputs. Both parts share the same internal DAC design and true rail-to-rail output buffers. The AD7304 contains four independent multiplying reference inputs, while the AD7305 has one common reference input. The AD7304 uses a 3-wire SPI compatible serial data interface, while the AD7305 offers a 8-bit parallel data interface.
D/A Converter Section
directly to the same supply as the VDD or VSS pin (Figure 30). Under these conditions clean power supply voltages (low ripple, avoid switching supplies) appropriate for the application should be used.
VDD Q1 VOUTX Q2 120k
Each part contains four voltage-switched R-2R ladder DACs. Figure A shows a typical equivalent DAC. These DACs are designed to operate both single-supply or dual supply, depending on whether the user supplies a negative voltage on the VSS pin. In a single-supply application the VSS is tied to ground. In either mode the DAC output voltage is determined by the VREF input voltage and the digital data (D) loaded into the corresponding DAC register according to Equation 1. VOUT = VREF x D/256 (1) Note that the output full-scale polarity is the same as the VREF polarity for dc reference voltages.
VDD VREF DB7
VSS
Figure 30. Equivalent DAC Amplifier Output Circuit
AD7304 SERIAL DATA INTERFACE
2R R 2R VSS
VOUT
DB6
The AD7304 uses a 3-wire (CS, SDI, CLK) SPI compatible serial data interface. New serial data is clocked into the serial input register in a 12-bit data-word format. MSB bits are loaded first. Table II defines the 12 data-word bits. Data is placed on the SDI/SHDN pin and clocked into the register on the positive clock edge of CLK subject to the data setup and data hold time requirements specified in the TIMING SPECIFICATIONS. Data can only be clocked in while the CS chip select pin is active low. Only the last 12-bits clocked into the serial register will be interrogated when the CS pin returns to the logic high state, extra data bits are ignored. Since most microcontrollers output serial data in 8-bit bytes, two right justified data bytes can be written to the AD7304. Keeping the CS line low between the first and second byte transfer will result in a successful serial register update. Once the data is properly aligned in the shift register the positive edge of the CS initiates either the transfer of new data to the target DAC register, determined by the decoding of address bits A1 and A0, or the shutdown features will be activated based on the SAC or SDC bits. When either SAC or SDC pins are set (Logic = 0) the loading of new data determined by Bits B9 to B0 are still loaded, but the results do not appear on the buffer outputs until the device is brought out of the shutdown state. The selected DAC output voltages become high impedance with a nominal resistance of 120 k to ground, Figure 30. If both SAC and SDC pins are set, all channels are still placed in the shutdown mode. When the AD7304 has been programmed into the power shutdown state, the present DAC register data is maintained as long as VDD remains greater than 2.7 volts. The remaining characteristics of the software serial interface are defined by Tables I, II and Figure 3 timing diagram. Two additional pins CLR and LDAC on the AD7304 provide hardware control over the clear function and the DAC Register loading. If these functions are not needed the CLR pin can be tied to logic high, and the LDAC pin can be tied to logic low. The asynchronous input CLR pin forces all input and DAC registers to the zero-code state. The asynchronous LDAC pin can be strobed to active low when all DAC Registers need to be updated simultaneously from their respective Input Registers. The LDAC pin places the DAC Register in a transparent mode while in the logic low state.
DB0
2R 2R
Figure 29. Typical Equivalent DAC Channel
These DACs are also designed to accommodate ac reference input signals. As long as the ac signals are maintained between VSS < VREF AD7305 allows the user to connect the reference inputs
REV. A
-11-
AD7304/AD7305
VREFA VREFB VREFC VREFD VDD
VREF VDD
CS CLK
EN
AD7304
D0 D1 D2 D3 D4 D5 D6 D7 A0 A1 SDC SAC VDD 640k 680k
INPUT REGISTER DAC C REGISTER DAC C
R OE
DATA DB0-DB7
DAC A
OE
8
AD7305
INPUT REGISTER R DAC A REGISTER R
SDI
INPUT REGISTER R
DAC A REGISTER R
VOUTA
WR
DAC A
OE
VOUTA
8
g
DQ DACA
INPUT REGISTER R DAC B REGISTER R
B 2:4 C DECODE D
DAC B
OE
VOUTB
A1 A0/SHDN
DAC A B 2:4 C DECODE D
INPUT REGISTER R
DAC B REGISTER R
DAC B
OE
VOUTB
g
DQ
R
VOUTC
VDD 640k 680k
INPUT REGISTER
R
DAC C REGISTER
DAC C
R OE
VOUTC
g
DQ
INPUT REGISTER R DAC D REGISTER R DAC D
OE
VOUTD
80k
INPUT REGISTER R
DAC D REGISTER R
DAC D
OE
VOUTD
80k
g
DQ 320k POWERON RESET
280k
280k
320k
POWERON RESET
GND
LDAC
CLR
VSS
GND
LDAC
VSS
Figure 31. AD7304 Equivalent Logic Interface
AD7304 Hardware Shutdown SHDN
Figure 32. AD7305 Equivalent Logic Interface
If a three-state driver is used on the SDI/SHDN pin, the AD7304 can be placed into a power shutdown mode when the SDI/ SHDN pin is placed in a high impedance state. For proper operation no other termination voltages should be present on this pin. An internal window comparator will detect when the logic voltage on the SHDN pin is between 28% and 36% of VDD. A high impedance internal bias generator provides this voltage on the SHDN pin. The four DAC output voltages become high impedance with a nominal resistance of 120 k to ground. See Figure 30 for an equivalent circuit.
AD7304/AD7305 POWER ON RESET
the same time. This will result in the analog outputs all changing to their new values at the same time. The LDAC pin is a level-sensitive input. If the simultaneous update feature is not required the LDAC pin can be tied to logic low. When the LDAC is tied to logic low, the DAC Registers become transparent and the Input Register data determines the DAC output voltage. See Figure 32 for an equivalent interface logic diagram.
AD7226 Pin Compatibility
By tying the LDAC pin to ground, the AD7305 has the same pin out and functionality as the AD7226, with the exception of a lower power supply operating voltage.
AD7305 Hardware Shutdown SHDN
When the VDD power supply is turned on, an internal reset strobe forces all the Input and DAC registers to the zero-code state. The VDD power supply should have a monotonically increasing ramp in order to have consistent results, especially in the region of VDD = 1.5 V to 2.3 V. The VSS supply has no effect on the power ON reset performance. The DAC register data will stay at zero until a valid serial register software load takes place. In the case of the double buffered AD7305 the output DAC register can only be changed once the LDAC strobe is initiated.
AD7305 PARALLEL DATA INTERFACE
If a three state driver is used on the A0/SHDN pin, the AD7305 can be placed into a power shutdown mode when the A0/SHDN pin is placed in a high impedance state. For proper operation no other termination voltages should be present on this pin. An internal window comparator will detect when the logic voltage on the SHDN pin is between 28% and 36% of VDD. A high impedance internal bias generator provides this voltage on the SHDN pin. The four DAC output voltages become high impedance with a nominal resistance of 120 k to ground.
ESD Protection Circuits
The AD7305 has an 8-bit parallel interface DB7 = MSB, DB0 = LSB. Two address Bits A1 and A0 are decoded when an active low write strobe is placed on the WR pin, see Table III. The WR is a level-sensitive input pin, therefore the data setup and data hold times defined in the TIMING SPECIFICATIONS need to be adhered to. The LDAC pin provides the capability of simultaneously updating all DAC registers with new data from the Input Registers at
All logic input pins contain back-biased ESD protection Zeners connected to ground (GND). The VREF pins also contain a back-biased ESD protection Zener connected to VDD (see Figure 33).
DIGITAL INPUTS VDD
VREFX GND
Figure 33. Equivalent ESD Protection Circuits
-12-
REV. A
AD7304/AD7305
APPLICATIONS
+5V 10k 10k
The AD7304/AD7305 is inherently a 2-quadrant multiplying D/A converter. That is, it can easily be set up for unipolar output operation. The full-scale output polarity is the same as the reference input voltage polarity. In some applications it may be necessary to generate the full 4-quadrant multiplying capability or a bipolar output swing. This is easily accomplished using an external true rail-to-rail op amp, such as the OP295. Connecting the external amplifier with two equal value resistors as shown in Figure 34 results in a full 4-quadrant multiplying circuit. In this circuit the amplifier provides a gain of two, which increases the output span magnitude to 10 volts. The transfer equation of this circuit shows that both negative and positive output voltages are created as the input data (D) is incremented from code zero (VOUT = -5 V) to midscale (VOUT = 0 V) to full scale (VOUT = +5 V). VOUT = (D/128 -1) x VREF (2)
-5V < VOUT < +5V REF
AD7304
Figure 34. Four-Quadrant Multiplying Application Circuit
REV. A
-13-
AD7304/AD7305
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
16-Lead Wide SOIC (R-16)
0.4133 (10.50) 0.3977 (10.00)
16 9
20
20-Lead SOIC (R-20)
0.5118 (13.00) 0.4961 (12.60)
11
0.4193 (10.65) 0.3937 (10.00)
0.4193 (10.65) 0.3937 (10.00)
0.2992 (7.60) 0.2914 (7.40)
0.2992 (7.60) 0.2914 (7.40)
1
8
1
10
PIN 1 0.0118 (0.30) 0.0040 (0.10)
0.1043 (2.65) 0.0926 (2.35)
0.0291 (0.74) x 45 0.0098 (0.25)
PIN 1
0.1043 (2.65) 0.0926 (2.35)
0.0291 (0.74) x 45 0.0098 (0.25)
0.0500 (1.27) BSC
0.0192 (0.49) SEATING 0.0138 (0.35) PLANE
8 0.0125 (0.32) 0 0.0091 (0.23)
0.0500 (1.27) 0.0157 (0.40)
0.0118 (0.30) 0.0040 (0.10)
8 0.0500 0.0192 (0.49) 0 (1.27) 0.0138 (0.35) SEATING 0.0125 (0.32) PLANE 0.0091 (0.23) BSC
0.0500 (1.27) 0.0157 (0.40)
16-Lead Plastic DIP (N-16)
0.840 (21.33) 0.745 (18.93)
16 1 9 8
20-Lead Plastic DIP (N-20)
1.060 (26.90) 0.925 (23.50)
20 11 10
0.280 (7.11) 0.240 (6.10) 0.060 (1.52) 0.015 (0.38) 0.130 (3.30) MIN
PIN 1 0.210 (5.33) MAX 0.160 (4.06) 0.115 (2.93) 0.022 (0.558) 0.014 (0.356) 0.100 (2.54) BSC
0.325 (8.25) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93)
1
0.280 (7.11) 0.240 (6.10) 0.060 (1.52) 0.015 (0.38) 0.130 (3.30) MIN
PIN 1 0.210 (5.33) MAX
0.325 (8.25) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93)
0.070 (1.77) SEATING 0.045 (1.15) PLANE
0.015 (0.381) 0.008 (0.204)
0.160 (4.06) 0.115 (2.93) 0.022 (0.558) 0.014 (0.356) 0.100 (2.54) BSC
0.070 (1.77) SEATING 0.045 (1.15) PLANE
0.015 (0.381) 0.008 (0.204)
16-Lead TSSOP (RU-16)
0.201 (5.10) 0.193 (4.90)
16 9
20-Lead Thin Surface Mount (TSSOP) (RU-20)
0.260 (6.60) 0.252 (6.40)
20 11
0.177 (4.50) 0.169 (4.30)
0.177 (4.50) 0.169 (4.30)
0.256 (6.50) 0.246 (6.25)
0.256 (6.50) 0.246 (6.25)
1
8
1
10
0.006 (0.15) 0.002 (0.05)
PIN 1 0.0433 (1.10) MAX 0.0118 (0.30) 0.0075 (0.19)
0.006 (0.15) 0.002 (0.05) 8 0 0.028 (0.70) 0.020 (0.50)
PIN 1 0.0433 (1.10) MAX 0.0256 (0.65) 0.0118 (0.30) BSC 0.0075 (0.19)
0.0256 SEATING (0.65) PLANE BSC
0.0079 (0.20) 0.0035 (0.090)
SEATING PLANE
8 0 0.0079 (0.20) 0.0035 (0.090)
0.028 (0.70) 0.020 (0.50)
-14-
REV. A
PRINTED IN U.S.A.
C3252a-2-2/98


▲Up To Search▲   

 
Price & Availability of AD7305

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X