|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
(R) SP3223EH/3243EH High Speed Intelligent +3.0V to +5.5V RS-232 Transceivers s Meets true EIA/TIA-232-F Standards from a +3.0V to +5.5V power supply s Interoperable with EIA/TIA-232 and adheres to EIA/TIA-562 down to a +2.7V power source s Auto-OnlineTM circuitry automatically wakes up from a 1A shutdown s Regulated Charge Pump Yields Stable RS-232 Outputs Regardless of VCC Variations s Enhanced ESD Specifications: +15KV Human Body Model +15KV IEC1000-4-2 Air Discharge +8KV IEC1000-4-2 Contact Discharge s 460 Kbps minimum transmission rate s Ideal for High Speed RS-232 Applications DESCRIPTION The SP3223EH and 3243EH products are RS-232 transceiver solutions intended for portable or hand-held applications such as notebook and palmtop computers. The "H" series is based on Sipex's SP3223E/3243E series and has been enhanced for high speed. The data rate is improved to 460Kbps, easily meeting the demands of high speed RS-232 applications. The SP3223EH and 3243EH use an internal high-efficiency, charge-pump power supply that requires only 0.1F capacitors in 3.3V operation. This charge pump and Sipex's driver architecture allow the SP3223EH/3243EH series to deliver compliant RS-232 performance from a single power supply ranging from +3.3V to +5.0V. The SP3223EH is a 2-driver/2-receiver device, and the SP3243EH is a 3-driver/5-receiver device, ideal for laptop/notebook computer and PDA applications. The SP3243EH includes one complementary receiver that remains alert to monitor an external device's Ring Indicate signal while the device is shutdown. The Auto-Online feature allows the device to automatically "wake-up" during a shutdown state when an RS-232 cable is connected and a connected peripheral is turned on. Otherwise, the device automatically shuts itself down drawing less than 1A. SELECTION TABLE Device SP3223EH SP3243EH Power Supplies +3.0V to +5.5V +3.0V to +5.5V RS-232 Drivers 2 3 RS-232 Receivers 2 5 External Components 4 capacitors 4 capacitors Auto-Online Circuitry YES YES TTL 3-State YES YES No. of Pins 20 28 Applicable U.S. Patents - 5,306,954; and other patents pending. SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 1 ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability and cause permanent damage to the device. VCC.......................................................-0.3V to +6.0V V+ (NOTE 1).......................................-0.3V to +7.0V V- (NOTE 1)........................................+0.3V to -7.0V V+ + |V-| (NOTE 1)...........................................+13V ICC (DC VCC or GND current).........................+100mA Input Voltages TxIN, ONLINE, SHUTDOWN, EN (SP3223EH).................-0.3V to +6.0V RxIN...................................................................+15V Output Voltages TxOUT...............................................................+15V RxOUT, STATUS.......................-0.3V to (VCC + 0.3V) Short-Circuit Duration TxOUT.....................................................Continuous Storage Temperature......................-65C to +150C Power Dissipation per package 20-pin PDIP (derate 16.0mW/oC above+70oC).....1300mW 20-pin SSOP (derate 9.25mW/oC above +70oC)....750mW 20-pin TSSOP (derate 11.1mW/oC above +70oC)..900mW 28-pin SOIC (derate 12.7mW/oC above +70oC)....1000mW 28-pin SSOP (derate 11.2mW/oC above +70oC).....900mW NOTE 1: V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V. SPECIFICATIONS Unless otherwise noted, the following specifications apply for VCC = +3.0V to +5.5V with TAMB = TMIN to TMAX. Typical values apply at VCC = +3.3V or +5.0V and TAMB = 25C. PARAMETER DC CHARACTERISTICS Supply Current, Auto-Online 1.0 10 A All RxIN open, ONLINE = GND, SHUTDOWN = VCC, VCC = +3.3V, TAMB = +25 C SHUTDOWN = GND, VCC = +3.3V, TAMB = +25 C ONLINE = SHUTDOWN = VCC, no load, VCC = +3.3V, TAMB = +25 C MIN. TYP. MAX. UNITS CONDITIONS Supply Current, Shutdown Supply Current, Auto-Online Disabled LOGIC INPUTS AND RECEIVER OUTPUTS Input Logic Threshold LOW HIGH Input Leakage Current Output Leakage Current Output Voltage LOW Output Voltage HIGH VCC - 0.6 1.0 0.3 10 1.0 A mA 0.8 2.0 +0.01 +0.05 +1.0 +10 0.4 VCC - 0.1 V A A V V VCC = +3.3V or +5.0V, TxIN, EN (SP3223EH), ONLINE, SHUTDOWN TxIN, EN, ONLINE, SHUTDOWN, TAMB = +25 C Receivers disabled IOUT = 1.6mA IOUT = -1.0mA SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 2 Unless otherwise noted, the following specifications apply for VCC = +3.0V to +5.5V with TAMB = TMIN to TMAX. Typical values apply at VCC = +3.3V or +5.0V and TAMB = 25C. SPECIFICATIONS (continued) PARAMETER DRIVER OUTPUTS Output Voltage Swing Output Resistance Output Short-Circuit Current Output Leakage Current MIN. TYP. MAX. UNITS CONDITIONS +5.0 300 +5.4 V All driver outputs loaded with 3K to GND, TAMB = +25 C VCC = V+ = V- = 0V, VOUT = 2V VOUT = 0V VOUT = 15V VCC = 0V or 3.0V to 5.5V, VOUT = +12V, Drivers disabled +35 +70 +60 +100 25 mA A RECEIVER INPUTS Input Voltage Range Input Threshold LOW Input Threshold LOW Input Threshold HIGH Input Threshold HIGH Input Hysteresis Input Resistance 3 -15 0.6 0.8 1.2 1.5 1.5 1.8 0.3 5 7 2.4 2.4 15 V V V V V V k VCC = 3.3V VCC = 5.0V VCC = 3.3V VCC = 5.0V Auto-Online CIRCUITRY CHARACTERISTICS (ONLINE = GND, SHUTDOWN = VCC) STATUS Output Voltage LOW STATUS Output Voltage HIGH Receiver Threshold to Drivers Enabled (tONLINE) Receiver Positive or Negative Threshold to STATUS HIGH (tSTSH) Receiver Positive or Negative Threshold to STATUS LOW (tSTSL) VCC - 0.6 200 0.5 0.4 V V S S IOUT = 1.6mA IOUT = -1.0mA Figure 15 Figure 15 20 S Figure 15 SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 3 SPECIFICATIONS (continued) Unless otherwise noted, the following specifications apply for VCC = +3.0V to +5.5V with TAMB = TMIN to TMAX. Typical values apply at VCC = +3.3V or +5.0V and TAMB = 25C. PARAMETER TIMING CHARACTERISTICS Maximum Data Rate Receiver Propagation Delay tPHL tPLH Receiver Output Enable Time Receiver Output Disable Time Driver Skew Receiver Skew Transition-Region Slew Rate MIN. TYP. MAX. UNITS CONDITIONS 460 Kbps s ns ns 100 1000 ns ns V/s RL = 3K, CL = 1000pF, one driver active Receiver input to Receiver output, CL = 150pF Normal operation Normal operation | tPHL - tPLH | | tPHL - tPLH | VCC= 3.3V, RL = 3K, TAMB = 25oC, measurements taken from -3.0V to +3.0V or +3.0V to -3.0V 0.3 0.3 200 200 50 200 60 TYPICAL PERFORMANCE CHARACTERISTICS Unless otherwise noted, the following performance characteristics apply for VCC = +3.3V, 235Kbps data rate, all drivers loaded with 3k, 0.1F charge pump capacitors, and TAMB = +25C. 14 6 12 10 Transmitter Output Voltage [V] 4 2 0 0 -2 -4 -6 Load Capacitance [pF] 500 1000 1500 Vout+ VoutSlew Rate [V/s] 8 6 4 2 0 0 500 1000 1500 Load Capacitance [pF] 2000 +Slew -Slew Figure 1. Transmitter Output Voltage VS. Load Capacitance for the SP3223EH Figure 2. Slew Rate VS. Load Capacitance for the SP3223EH SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 4 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise noted, the following performance characteristics apply for VCC = +3.3V, 235Kbps data rate, all drivers loaded with 3k, 0.1F charge pump capacitors, and TAMB = +25C. 40 35 30 25 20 15 10 5 118KHz 60KHz 10KHz 6 Transmitter Output Voltage [V] Supply Current [mA] 4 2 0 0 -2 -4 -6 500 1000 1500 2000 2500 Vout+ Vout- 0 0 500 1000 1500 Load Capacitance [pF] 2000 Load Capacitance [pF] Figure 3. Supply Current VS. Load Capacitance when Transmitting Data for the SP3223EH Figure 4. Transmitter Output Voltage VS. Load Capacitance for the SP3243EH 16 14 12 10 8 6 4 2 0 0 500 1000 1500 2000 2500 3000 Load Capacitance [pF] + Slew - Slew 80 70 60 50 40 30 20 10 0 0 500 1000 1500 2000 2500 3000 Load Capacitance [pF] 118KHz 60KHz 10KHz Figure 5. Slew Rate VS. Load Capacitance for the SP3243EH Figure 6. Supply Current VS. Load Capacitance when Transmitting Data for the SP3243EH SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers Supply Current [mA] Slew Rate [V/s] (c) Copyright 2000 Sipex Corporation 5 PIN NUMBER NAME FUNCTION SP3223EH SP3243EH EN C1+ V+ C1C2+ C2VR1IN R2IN R3IN R4IN R5IN R1OUT R2OUT R2OUT R3OUT R4OUT R5OUT STATUS T1IN T2IN T3IN ONLINE T1OUT T2OUT T3OUT GND VCC SHUTDOWN Receiver Enable. Apply logic LOW for normal operation. Apply logic HIGH to disable the receiver outputs (high-Z state). Positive terminal of the voltage doubler charge-pump capacitor. Regulated +5.5V output generated by the charge pump. Negative terminal of the voltage doubler charge-pump capacitor. Positive terminal of the inverting charge-pump capacitor. Negative terminal of the inverting charge-pump capacitor. Regulated -5.5V output generated by the charge pump. RS-232 receiver input. RS-232 receiver input. RS-232 receiver input. RS-232 receiver input. RS-232 receiver input. TTL/CMOS receiver output. TTL/CMOS receiver output. Non-inverting receiver-2 output, active in shutdown. TTL/CMOS receiver output. TTL/CMOS receiver output. TTL/CMOS receiver output. TTL/CMOS Output indicating online and shutdown status. TTL/CMOS driver input. TTL/CMOS driver input. TTL/CMOS driver input. Apply logic HIGH to override Auto-Online circuitry keeping drivers active (SHUTDOWN must also be logic HIGH, refer to Table 2). RS-232 driver output. RS-232 driver output. RS-232 driver output. Ground. +3.0V to +5.5V supply voltage. Apply logic LOW to shut down drivers and charge pump. This overrides all Auto-Online circuitry and ONLINE (refer to Table 2). 1 2 3 4 5 6 7 16 9 15 10 11 13 12 14 17 8 18 19 20 28 27 24 1 2 3 4 5 6 7 8 19 18 20 17 16 15 21 14 13 12 23 9 10 11 25 26 22 Table 1. Device Pin Description SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 6 EN 1 20 SHUTDOWN 19 VCC 18 GND 17 SP3223EH 16 T1OUT R1IN C1+ 2 V+ C1C2+ C2VT2OUT R2IN 3 4 5 6 7 8 9 15 R1OUT 14 ONLINE 13 T1IN 12 T2IN 11 STATUS R2OUT 10 Figure 7. SP3223EH Pinout Configuration C2+ 1 C2- 2 VR1IN R2IN R3IN R4IN 3 4 5 6 7 28 C1+ 27 26 25 24 V+ VCC GND C1- SP3243EH 23 ONLINE 22 SHUTDOWN 21 STATUS 20 19 18 17 16 15 R2OUT R1OUT R2OUT R3OUT R4OUT R5OUT R5IN 8 T1OUT 9 T2OUT 10 T3OUT 11 T3IN 12 T2IN 13 T1IN 14 Figure 8. SP3243EH Pinout Configuration SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 7 +3V to +5V C5 + 0.1F 2 C1+ 0.1F 4 C15 C2+ 19 VCC V+ 3 C3 + 0.1F C1 + C2 + SP3223EH V- 7 C4 + 0.1F 0.1F 6 C213 T1IN T1OUT 17 T2OUT 8 TTL/CMOS INPUTS 12 T2IN RS-232 OUTPUTS 15 R1OUT TTL/CMOS OUTPUTS 10 R2OUT 5K 1 VCC 20 14 To P Supervisor Circuit R1IN 5K R2IN 16 RS-232 INPUTS 9 EN SHUTDOWN ONLINE STATUS GND 18 11 Figure 9. SP3223EH Typical Operating Circuit SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 8 C5 + VCC 0.1F 28 C1+ 0.1F 24 C11 C2+ 26 VCC V+ 27 C3 + 0.1F C1 + C2 + SP3243EH V- 3 C4 + 0.1F 0.1F 2 C214 T1IN T1OUT 9 RS-232 OUTPUTS TTL/CMOS INPUTS 13 T2IN 12 T3IN 20 R2OUT 19 R1OUT 5K 18 R2OUT T2OUT 10 T3OUT 11 R1IN R2IN 4 5 6 7 8 RS-232 INPUTS TTL/CMOS OUTPUTS 5K 17 R3OUT 5K 16 R4OUT 5K 15 VCC R3IN R4IN R5IN R5OUT 22 23 5K SHUTDOWN ONLINE To P Supervisor Circuit 21 STATUS GND 25 Figure 10. SP3243EH Typical Operating Circuit SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 9 DESCRIPTION The SP3223EH and SP3243EH transceivers meet the EIA/TIA-232 and ITU-T V.28/V.24 communication protocols and can be implemented in battery-powered, portable, or hand-held applications such as notebook or palmtop computers. The SP3223EH and SP3243EH devices feature Sipex's proprietary and patented (U.S.-- 5,306,954) on-board charge pump circuitry that generates +5.5V RS-232 voltage levels from a single +3.0V to +5.5V power supply. The SP3223EH and SP3243EH devices can operate at a data rate of 460Kbps fully loaded. The SP3223EH is a 2-driver/2-receiver device, and the SP3243EH is a 3-driver/5-receiver device, ideal for portable or hand-held applications. The SP3243EH includes one complementary always-active receiver that can monitor an external device (such as a modem) in shutdown. This aids in protecting the UART or serial controller IC by preventing forward biasing of the protection diodes where VCC may be disconnected. The SP3223EH and SP3243EH series is an ideal choice for power sensitive designs. The SP3223EH and SP3243EH devices feature Auto-Online circuitry which reduces the power supply drain to a 1A supply current. In many portable or hand-held applications, an RS-232 cable can be disconnected or a connected peripheral can be turned off. Under these conditions, the internal charge pump and the drivers will be shut down. Otherwise, the system automatically comes online. This feature allows design engineers to address power saving concerns without major design changes. THEORY OF OPERATION The SP3223EH and SP3243EH series is made up of four basic circuit blocks: 1. Drivers, 2. Receivers, 3. the Sipex proprietary charge pump, and 4. Auto-Online circuitry. Drivers The drivers are inverting level transmitters that convert TTL or CMOS logic levels to 5.0V EIA/ TIA-232 levels with an inverted sense relative to the input logic levels. Typically, the RS-232 output voltage swing is +5.4V with no load and +5V minimum fully loaded. The driver outputs are protected against infinite short-circuits to ground without degradation in reliability. These drivers comply with the EIA-TIA-232-F and all previous RS-232 versions. The drivers can guarantee a data rate over 460Kbps fully loaded with 3K in parallel with 1000pF, ensuring compatibility with PC-to-PC communication software. The slew rate of the driver output is internally limited to a maximum of 30V/s in order to meet the EIA standards (EIA RS-232D 2.1.7, Paragraph 5). The transition of the loaded output from HIGH to LOW also meets the monotonicity requirements of the standard. VCC + 0.1F 28 C1+ 0.1F 24 C11 C2+ C2 + 0.1F 2 C214 T1IN 13 T2IN 12 T3IN 20 R2OUT T1OUT C5 26 VCC V+ 27 C3 + 0.1F C1 + SP3243EH V- 3 C4 9 RS-232 OUTPUTS + 0.1F TxD RTS DTR T2OUT 10 T3OUT 11 UART or Serial C RxD CTS DSR DCD RI VCC 19 R1OUT 5K 18 R2OUT 5K 17 R3OUT 5K 16 R4OUT 5K 15 R5OUT 22 23 5K SHUTDOWN ONLINE R1IN 4 R2IN R3IN R4IN R5IN 5 6 7 8 RS-232 INPUTS 21 STATUS GND 25 RESET P Supervisor IC VIN Figure 11. Interface Circuitry Controlled by Microprocessor Supervisory Circuit SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 10 DEVICE: SP3223EH SHUTDOWN 0 0 1 1 EN 0 1 0 1 TXOUT High Z High Z Active Active RXOUT Active C2 + 0.1F C5 + 0.1F 2 C1+ 0.1F 4 C15 C2+ 6 C2T1IN +3V to +5V 19 VCC V+ 3 C3 + 0.1F C1 + SP3223EH SP3243EH V- 7 C4 + 0.1F High Z Active High Z TTL/CMOS INPUTS T1OUT TXIN TXOUT R1OUT TTL/CMOS OUTPUTS RXOUT VCC 1 EN 20 14 SHUTDOWN ONLINE STATUS GND 18 5K 5K R1IN DEVICE: SP3243EH SHUTDOWN 0 1 TXOUT High Z Active RXOUT High Z Active R2OUT Active Active To P Supervisor Circuit RXIN 1000pF 1000pF 11 Table 2. SHUTDOWN and EN Truth Tables Note: In Auto-Online Mode where ONLINE = GND and SHUTDOWN = VCC, the device will shut down if there is no activity present at the Receiver inputs. Figure 12. Loopback Test Circuit for RS-232 Driver Data Transmission Rates The SP3223EH and SP3243EH drivers can maintain high data rates over 460Kbps fully loaded. Figure 12 shows a loopback test circuit used to test the RS-232 Drivers. Figure 13 shows the test results of the loopback circuit with all three drivers active at 120Kbps with typical RS-232 loads in parallel with 1000pF capacitors. Figure 14 shows the test results where one driver was active at 1Mbps and all three drivers loaded with an RS-232 receiver in parallel with a 1000pF capacitor. A superior RS-232 data transmission rate of 1Mbps makes the SP3223EH/3243EH series an ideal match for high speed LAN and personal computer peripheral applications. Receivers The receivers convert +5.0V EIA/TIA-232 levels to TTL or CMOS logic output levels. All receivers have an inverting output that can be disabled by using the EN pin. Figure 13. Loopback Test Circuit 1 Driver Fully Loaded SP3223EHDS/11 Figure 14. Loopback Test Circuit (All Drivers Fully Loaded) (c) Copyright 2000 Sipex Corporation SP3223EH +3.0V to +5.5V RS-232 Transceivers 11 Receivers are active when the Auto-Online circuitry is enabled or when in shutdown. During the shutdown, the receivers will continue to be active. If there is no activity present at the receivers for a period longer than 100s or when SHUTDOWN is enabled, the device goes into a standby mode where the circuit draws 1A. Driving EN to a logic HIGH forces the outputs of the receivers into high-impedance. The truth table logic of the SP3223EH and SP3243EH driver and receiver outputs can be found in Table 2. The SP3243EH includes an additional noninverting receiver with an output R2OUT. R2OUT is an extra output that remains active and monitors activity while the other receiver outputs are forced into high impedance. This allows Ring Indicator (RI) from a peripheral to be monitored without forward biasing the TTL/CMOS inputs of the other devices connected to the receiver outputs. Since receiver input is usually from a transmission line where long cable lengths and system interference can degrade the signal, the inputs have a typical hysteresis margin of 300mV. This ensures that the receiver is virtually immune to noisy transmission lines. Should an input be left unconnected, an internal 5K pulldown resistor to ground will commit the output of the receiver to a HIGH state. Charge Pump The charge pump is a Sipex-patented design (U.S. 5,306,954) and uses a unique approach compared to older less-efficient designs. The charge pump still requires four external capacitors, but uses a four-phase voltage shifting technique to attain symmetrical 5.5V power supplies. The internal power supply consists of a regulated dual charge pump that provides output voltages 5.5V regardless of the input voltage (VCC) over the +3.0V to +5.5V range. This is important to maintain compliant RS-232 levels regardless of power supply fluctuations. The charge pump operates in a discontinuous mode using an internal oscillator. If the output voltages are less than a magnitude of 5.5V, the charge pump is enabled. If the output voltages exceed a magnitude of 5.5V, the charge pump is disabled. This oscillator controls the four phases of the voltage shifting. A description of each phase follows. Phase 1 -- VSS charge storage -- During this phase of the clock cycle, the positive side of capacitors C1 and C2 are initially charged to VCC. Cl+ is then switched to GND and the charge in C1- is transferred to C2-. Since C2+ is connected to VCC, the voltage potential across capacitor C2 is now 2 times VCC. Phase 2 -- VSS transfer -- Phase two of the clock connects the negative terminal of C2 to the VSS storage capacitor and the positive terminal of C2 to GND. This transfers a negative generated voltage to C 3 . This generated voltage is regulated to a minimum voltage of -5.5V. Simultaneous with the transfer of the voltage to C3, the positive side of capacitor C1 is switched to VCC and the negative side is connected to GND. Phase 3 -- VDD charge storage -- The third phase of the clock is identical to the first phase -- the charge transferred in C1 produces -VCC in the negative terminal of C1, which is applied to the negative side of capacitor C2. Since C2+ is at VCC, the voltage potential across C2 is 2 times VCC. Phase 4 -- VDD transfer -- The fourth phase of the clock connects the negative terminal of C2 to GND, and transfers this positive generated voltage across C2 to C4, the VDD storage capacitor. This voltage is regulated to +5.5V. At this voltage, the internal oscillator is disabled. Simultaneous with the transfer of the voltage to C4, the positive side of capacitor C1 is switched to VCC and the negative side is connected to GND, allowing the charge pump cycle to begin again. The charge pump cycle will continue as long as the operational conditions for the internal oscillator are present. SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 12 Since both V+ and V- are separately generated from VCC, in a no-load condition V+ and V- will be symmetrical. Older charge pump approaches that generate V- from V+ will show a decrease in the magnitude of V- compared to V+ due to the inherent inefficiencies in the design. The clock rate for the charge pump typically operates at 250kHz. The external capacitors can be as low as 0.1F with a 16V breakdown voltage rating. RECEIVER +2.7V 0V RS-232 INPUT VOLTAGES -2.7V VCC STATUS 0V S H U T D O W N tSTSL tSTSH tONLINE +5V DRIVER RS-232 OUTPUT VOLTAGES 0V -5V Figure 15. Auto-Online Timing Waveforms SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 13 VCC = +5V +5V C1 + - C4 + - + C2 + - - VDD Storage Capacitor VSS Storage Capacitor -5V -5V C3 Figure 16. Charge Pump -- Phase 1 VCC = +5V C4 + - + C1 + - C2 + - - VDD Storage Capacitor VSS Storage Capacitor -10V C3 Figure 17. Charge Pump -- Phase 2 [ T ] +6V a) C2+ 1 2 2 T 0V 0V b) C2T -6V Ch1 2.00V Ch2 2.00V M 1.00s Ch1 1.96V Figure 18. Charge Pump Waveforms VCC = +5V +5V C1 + - C4 + - + C2 + - - VDD Storage Capacitor VSS Storage Capacitor -5V -5V C3 Figure 19. Charge Pump -- Phase 3 VCC = +5V +10V C1 + - C4 + - + C2 + - - VDD Storage Capacitor VSS Storage Capacitor C3 Figure 20. Charge Pump -- Phase 4 SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 14 6 Transmitter Output Voltage [V] 4 2 0 -2 -4 -6 Load Current Per Transmitter [mA] Vout+ Vout0.62 0.869 0.939 1.02 1.12 1.23 1.38 1.57 1.82 2.67 3.46 4.93 8.6 Figure 21. SP3243EH Driver Output Voltages vs. Load Current per Transmitter C5 + VCC 0.1F 28 C1+ 0.1F 24 C11 C2+ 26 VCC V+ 27 C3 + 0.1F C1 + SP3243EH C2 + V- 3 C4 + 0.1F 0.1F 2 C214 T1IN 13 T2IN 12 T3IN 20 R2OUT 19 R1OUT 5K 18 R2OUT 5K 17 R3OUT 5K 16 R4OUT 5K 15 R5OUT R5IN R4IN 7 R3IN R2IN 5 R1IN 4 T1OUT 9 T2OUT 10 T3OUT 11 6 8 VCC 22 23 5K SHUTDOWN ONLINE DB-9 Connector 6 7 8 9 1 2 3 4 5 To P Supervisor Circuit 21 STATUS GND 25 DB-9 Connector Pins: 1. Received Line Signal Detector 2. Received Data 3. Transmitted Data 4. Data Terminal Ready 5. Signal Ground (Common) 6. 7. 8. 9. DCE Ready Request to Send Clear to Send Ring Indicator Figure 22. Circuit for the connectivity of the SP3243EH with a DB-9 connector SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 15 RS-232 SIGNAL AT RECEIVER INPUT SHUTDOWN INPUT ONLINE INPUT STATUS OUTPUT TRANSCEIVER STATUS Normal Operation Normal Operation Shutdown (Auto-Online) Shutdown Shutdown YES NO NO YES NO Table 3. Auto-Online Logic HIGH HIGH HIGH LOW LOW HIGH LOW - HIGH LOW LOW HIGH LOW Inactive Detection Block RXINACT RXIN RS-232 Receiver Block RXOUT Figure 23. Stage I of Auto-Online Circuitry Delay Stage Delay Stage Delay Stage Delay Stage Delay Stage STATUS R1INACT R2INACT R3INACT R4INACT R5INACT SHUTDOWN Figure 24. Stage II of Auto-Online Circuitry SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 16 Auto-Online Circuitry The SP3223EH and SP3243EH devices have a patent pending Auto-Online circuitry on board that saves power in applications such as laptop computers, palmtop (PDA) computers and other portable systems. The SP3223EH and SP3243EH devices incorporate an Auto-Online circuit that automatically enables itself when the external transmitters are enabled and the cable is connected. Conversely, the Auto-Online circuit also disables most of the internal circuitry when the device is not being used and goes into a standby mode where the device typically draws 1A. This function can also be externally controlled by the ONLINE pin. When this pin is tied to a logic LOW, the Auto-Online function is active. Once active, the device is enabled until there is no activity on the receiver inputs. The receiver input typically sees at least +3V, which are generated from the transmitters at the other end of the cable with a +5V minimum. When the external transmitters are disabled or the cable is disconnected, the receiver inputs will be pulled down by their internal 5k resistors to ground. When this occurs over a period of time, the internal transmitters will be disabled and the device goes into a shutdown or standy mode. When ONLINE is HIGH, the Auto-Online mode is disabled. The Auto-Online circuit has two stages: 1) Inactive Detection 2) Accumulated Delay The first stage, shown in Figure 23, detects an inactive input. A logic HIGH is asserted on RXINACT if the cable is disconnected or the external transmitters are disabled. Otherwise, RXINACT will be at a logic LOW. This circuit is duplicated for each of the other receivers. The second stage of the Auto-Online circuitry, shown in Figure 24, processes all the receiver's RXINACT signals with an accumulated delay that disables the device to a 1A supply current. The STATUS pin goes to a logic LOW when the cable is disconnected, the external transmitters are disabled, or the SHUTDOWN pin is invoked. The typical accumulated delay is around 20s. When the SP3223EH and SP3243EH drivers or internal charge pump are disabled, the supply current is reduced to 1A. This can commonly occur in hand-held or portable applications where the RS-232 cable is disconnected or the RS-232 drivers of the connected peripheral are turned off. The Auto-Online mode can be disabled by the SHUTDOWN pin. If this pin is a logic LOW, the Auto-Online function will not operate regardless of the logic state of the ONLINE pin. Table 3 summarizes the logic of the Auto-Online operating modes. The truth table logic of the SP3223EH and SP3243EH driver and receiver outputs can be found in Table 2. The STATUS pin outputs a logic LOW signal if the device is shutdown. This pin goes to a logic HIGH when the external transmitters are enabled and the cable is connected. When the SP3223EH and SP3243EH devices are shut down, the charge pumps are turned off. V+ charge pump output decays to VCC, the V- output decays to GND. The decay time will depend on the size of capacitors used for the charge pump. Once in shutdown, the time required to exit the shut down state and have valid V+ and V- levels is typically 200s. For easy programming, the STATUS can be used to indicate DTR or a Ring Indicator signal. Tying ONLINE and SHUTDOWN together will bypass the Auto-Online circuitry so this connection acts like a shutdown input pin. SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 17 ESD TOLERANCE The SP3223EH/3243EH series incorporates ruggedized ESD cells on all driver output and receiver input pins. The ESD structure is improved over our previous family for more rugged applications and environments sensitive to electro-static discharges and associated transients. The improved ESD tolerance is at least +15kV without damage nor latch-up. There are different methods of ESD testing applied: a) MIL-STD-883, Method 3015.7 b) IEC1000-4-2 Air-Discharge c) IEC1000-4-2 Direct Contact normal usage. The transceiver IC receives most of the ESD current when the ESD source is applied to the connector pins. The test circuit for IEC1000-4-2 is shown on Figure 26. There are two methods within IEC1000-4-2, the Air Discharge method and the Contact Discharge method. With the Air Discharge Method, an ESD voltage is applied to the equipment under test (EUT) through air. This simulates an electrically charged person ready to connect a cable onto the rear of the system only to find an unpleasant zap just before the person touches the back panel. The high energy potential on the person discharges through an arcing path to the rear panel of the system before he or she even touches the system. This energy, whether discharged directly or through air, is predominantly a function of the discharge current rather than the discharge voltage. Variables with an air discharge such as approach speed of the object carrying the ESD potential to the system and humidity will tend to change the discharge current. For example, the rise time of the discharge current varies with the approach speed. The Contact Discharge Method applies the ESD current directly to the EUT. This method was devised to reduce the unpredictability of the ESD arc. The discharge current rise time is constant since the energy is directly transferred without the air-gap arc. In situations such as hand held systems, the ESD charge can be directly discharged to the equipment from a person already holding the equipment. The current is transferred on to the keypad or the serial port of the equipment directly and then travels through the PCB and finally to the IC. The Human Body Model has been the generally accepted ESD testing method for semiconductors. This method is also specified in MIL-STD-883, Method 3015.7 for ESD testing. The premise of this ESD test is to simulate the human body's potential to store electro-static energy and discharge it to an integrated circuit. The simulation is performed by using a test model as shown in Figure 25. This method will test the IC's capability to withstand an ESD transient during normal handling such as in manufacturing areas where the ICs tend to be handled frequently. The IEC-1000-4-2, formerly IEC801-2, is generally used for testing ESD on equipment and systems. For system manufacturers, they must guarantee a certain amount of ESD protection since the system itself is exposed to the outside environment and human presence. The premise with IEC1000-4-2 is that the system is required to withstand an amount of static electricity when ESD is applied to points and surfaces of the equipment that are accessible to personnel during RC C SW1 SW1 DC Power Source RS RS SW2 SW2 CS S Device Under Test Figure 25. ESD Test Circuit for Human Body Model SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 18 Contact-Discharge Module RC RC SW1 DC Power Source RS S RV SW2 CS S Device Under Test RS and RV add up to 330 for IEC1000-4-2. 330 for Figure 26. ESD Test Circuit for IEC1000-4-2 The circuit models in Figures 25 and 26 represent the typical ESD testing circuit used for all three methods. The CS is initially charged with the DC power supply when the first switch (SW1) is on. Now that the capacitor is charged, the second switch (SW2) is on while SW1 switches off. The voltage stored in the capacitor is then applied through RS, the current limiting resistor, onto the device under test (DUT). In ESD tests, the SW2 switch is pulsed so that the device under test receives a duration of voltage. For the Human Body Model, the current limiting resistor (RS) and the source capacitor (CS) are 1.5k an 100pF, respectively. For IEC-1000-42, the current limiting resistor (RS) and the source capacitor (CS) are 330 an 150pF, respectively. The higher CS value and lower RS value in the IEC1000-4-2 model are more stringent than the Human Body Model. The larger storage capacitor injects a higher voltage to the test point when SW2 is switched on. The lower current limiting resistor increases the current charge onto the test point. DEVICE PIN TESTED Driver Outputs Receiver Inputs 30A 15A 0A t=0ns t Figure 27. ESD Test Waveform for IEC1000-4-2 t=30ns HUMAN BODY MODEL +15kV +15kV i Air Discharge +15kV +15kV IEC1000-4-2 Direct Contact +8kV +8kV Level 4 4 Table 4. Transceiver ESD Tolerance Levels SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 19 PACKAGE: PLASTIC DUAL-IN-LINE (NARROW) E1 E D1 = 0.005" min. (0.127 min.) D A1 = 0.015" min. (0.381min.) A = 0.210" max. (5.334 max). A2 C O eA = 0.300 BSC (7.620 BSC) L e = 0.100 BSC (2.540 BSC) B1 B ALTERNATE END PINS (BOTH ENDS) DIMENSIONS (Inches) Minimum/Maximum (mm) A2 B B1 C D E E1 L O 16-PIN 0.115/0.195 (2.921/4.953) 0.014/0.022 (0.356/0.559) 0.045/0.070 (1.143/1.778) 0.008/0.014 (0.203/0.356) 20-PIN 0.115/0.195 (2.921/4.953) 0.014/0.022 (0.356/0.559) 0.045/0.070 (1.143/1.778) 0.008/0.014 (0.203/0.356) 28-PIN 0.068/0.078 (1.73/1.99) 0.002/0.008 (0.05/0.21) 0.010/0.015 (0.25/0.38) 0.397/0.407 (10.07/10.33) 0.205/0.212 (5.20/5.38) 0.0256 BSC (0.65 BSC) 0.301/0.311 (7.65/7.90) 0.022/0.037 (0.55/0.95) 0/8 (0/8) 0.980/1.060 0.780/0.800 (19.812/20.320) (24.892/26.924) 0.300/0.325 (7.620/8.255) 0.240/0.280 (6.096/7.112) 0.115/0.150 (2.921/3.810) 0/ 15 (0/15) 0.300/0.325 (7.620/8.255) 0.240/0.280 (6.096/7.112) 0.115/0.150 (2.921/3.810) 0/ 15 (0/15) SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 20 PACKAGE: PLASTIC SHRINK SMALL OUTLINE (SSOP) E H D A O e B A1 L DIMENSIONS (Inches) Minimum/Maximum (mm) A A1 B D E e H L O 16-PIN 0.068/0.078 (1.73/1.99) 0.002/0.008 (0.05/0.21) 0.010/0.015 (0.25/0.38) 0.239/0.249 (6.07/6.33) 0.205/0.212 (5.20/5.38) 0.0256 BSC (0.65 BSC) 0.301/0.311 (7.65/7.90) 0.022/0.037 (0.55/0.95) 0/8 (0/8) 20-PIN 0.068/0.078 (1.73/1.99) 0.002/0.008 (0.05/0.21) 0.010/0.015 (0.25/0.38) 0.278/0.289 (7.07/7.33) 0.205/0.212 (5.20/5.38) 0.0256 BSC (0.65 BSC) 0.301/0.311 (7.65/7.90) 0.022/0.037 (0.55/0.95) 0/8 (0/8) 24-PIN 0.068/0.078 (1.73/1.99) 0.002/0.008 (0.05/0.21) 0.010/0.015 (0.25/0.38) 0.317/0.328 (8.07/8.33) 0.205/0.212 (5.20/5.38) 0.0256 BSC (0.65 BSC) 0.301/0.311 (7.65/7.90) 0.022/0.037 (0.55/0.95) 0/8 (0/8) 28-PIN 0.068/0.078 (1.73/1.99) 0.002/0.008 (0.05/0.21) 0.010/0.015 (0.25/0.38) 0.397/0.407 (10.07/10.33) 0.205/0.212 (5.20/5.38) 0.0256 BSC (0.65 BSC) 0.301/0.311 (7.65/7.90) 0.022/0.037 (0.55/0.95) 0/8 (0/8) SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 21 PACKAGE: PLASTIC SMALL OUTLINE (SOIC) (WIDE) E H D A O e B A1 L DIMENSIONS (Inches) Minimum/Maximum (mm) A A1 B D E e H L O 28-PIN 0.093/0.104 (2.352/2.649) 0.004/0.012 (0.102/0.300) 0.013/0.020 (0.330/0.508) 0.697/0.713 (17.70/18.09) 0.291/0.299 (7.402/7.600) 0.050 BSC (1.270 BSC) 0.394/0.419 (10.00/10.64) 0.016/0.050 (0.406/1.270) 0/8 (0/8) SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 22 PACKAGE: PLASTIC THIN SMALL OUTLINE (TSSOP) E2 E D A O e B A1 L DIMENSIONS in inches (mm) Minimum/Maximum A A1 B D E e E2 L O 20-PIN - /0.043 (- /1.10) 0.002/0.006 (0.05/0.15) 0.007/0.012 (0.19/0.30) 0.252/0.260 (6.40/6.60) 0.169/0.177 (4.30/4.50) 0.026 BSC (0.65 BSC) 0.126 BSC (3.20 BSC) 0.020/0.030 (0.50/0.75) 0/8 SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 23 ORDERING INFORMATION Please consult the factory for pricing and availability on a Tape-On-Reel option. Corporation SIGNAL PROCESSING EXCELLENCE Sipex Corporation Headquarters and Sales Office 22 Linnell Circle Billerica, MA 01821 TEL: (978) 667-8700 FAX: (978) 670-9001 e-mail: sales@sipex.com Sales Office 233 South Hillview Drive Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) 935-7600 Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. SP3223EHDS/11 SP3223EH +3.0V to +5.5V RS-232 Transceivers (c) Copyright 2000 Sipex Corporation 24 SP3243EHCT SP3243EHCA 0C to +70C 0C to +70C Model SP3223EHCP SP3223EHCA SP3223EHCY Temperature Range 0C to +70C 0C to +70C 0C to +70C Package Types 20-pin PDIP 20-pin SSOP 20-pin TSSOP 28-pin Wide SOIC 28-pin SSOP |
Price & Availability of SP3223EH |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |