| |
|
 |
MAXIM - Dallas Semiconductor
|
| Part No. |
DS5000TK 5000TK
|
| OCR Text |
...S
When KIT.EXE is invoked from MS-DOS, communication is automatically established with the DS5000T via its on-chip Serial Loader. KIT.EXE a...9600 bps). If no response is detected, then an error message to this effect is displayed to the user... |
| Description |
From old datasheet system
Microcontroller Evaluation Kit
|
| File Size |
47.20K /
5 Page |
 View
it Online |
Download Datasheet
|
| |
|
|
SUNYUAN
|
| Part No. |
ISOADA08
|
| OCR Text |
... Baud rate, 0~255 address. <100 ms 8~50VDC <1W - 45 ~ +85 10 ~ 90% (non-condensing) - 45 ~ +85 10 ~ 95% (non-condensing) 3KVDC,1 minute,le...9600 baud 19200 baud 38400 baud
Table 4 Data format,checksum
Bit7Not used(set to 0) Bit6checks... |
| Description |
Isolated 4-20mA to RS485 Converter
|
| File Size |
511.45K /
13 Page |
View
it Online |
Download Datasheet |
| |
|
|
http://
|
| Part No. |
CY7C67200 CY7C67200-48BAXI CY7C6720006 CY7C67200-BAXIT
|
| OCR Text |
...hould be noted that for up to 3 ms after bios starts executing, gpio[24:19] and gpio[15:8] will be driven as outputs for a test mode. if these pins need to be used as inputs, a series resistor is require d (10 ohm to 48 ohm is recom- mende... |
| Description |
EZ-OTG?/a> Programmable USB On-The-Go
|
| File Size |
796.16K /
78 Page |
View
it Online |
Download Datasheet |
| |
|
|
Vishay Semiconductors
|
| Part No. |
TOIM4232-TR1
|
| OCR Text |
... piezo resonators) and above 2 ms with high q quartzes. (2) all vishay semiconductor sir transceivers fulfill this condition. pin descript...9600 bit/s, sets pulse width to 1.627 s. the v cc _sd output is simply an inverted reset signal wh... |
| Description |
TOIM4232 SIR Endec for IrDA® Applications Integrated Interface Circuit
|
| File Size |
571.30K /
17 Page |
View
it Online |
Download Datasheet |
| |
|
|
Cypress Semiconductor Corp.
|
| Part No. |
CY7C67200
|
| OCR Text |
...hould be noted that for up to 3 ms after bios starts executing, gpio[24:19] and gpio[15:8] will be driven as outputs for a test mode. if these pins need to be used as inputs, a series resistor is required (10 ohm - 48 ohm is recom- mended)... |
| Description |
EZ-OTG Programmable USB On-The-Go Host/Peripheral Controller(EZ-OTG可编程USB On-The-Go主机/外围设备控制
|
| File Size |
873.14K /
82 Page |
View
it Online |
Download Datasheet |
| |
|
|
ETC[ETC]
|
| Part No. |
EDE702
|
| OCR Text |
...rammed to wait approximately 50 mS for the LCD to initialize. Following this, the display is ready to accept data for display. Before the fi...9600 Baud OPEN "com1:9600,n,8,1,cd0,cs0,ds0,op0,rs" FOR OUTPUT AS #1 REM Clear Display GOSUB 999 OUT... |
| Description |
Serial LCD Interface IC
|
| File Size |
198.82K /
9 Page |
View
it Online |
Download Datasheet |
|
Price and Availability
|
